ASM1232LP, ASM1232LPS 5 V mP Power Supply Monitor and Reset Circuit Description * * * * * * * * * * 5 V Supply Monitor Selectable Watchdog Period Debounce Manual Push-button Reset Input Precision Temperature-compensated Voltage Reference and Comparator Power-up, Power-down and Brown Out Detection 250 ms Minimum Reset Time Active LOW Open Drain Reset Output and Active HIGH Push-pull Output Selectable Trip Point Tolerance: 5% or 10% Low-cost Surface Mount Packages: 8-pin/16-pin SO, 8-pin DIP and 8-pin Micro SO Packages Wide Operating Temperature -40C to +85C (N Suffixed Devices) Applications * * * * * * August, 2011 - Rev. 3 MICRO-8 U SUFFIX CASE 846AA SOIC-8 S SUFFIX CASE 751BD SOIC-16 S SUFFIX CASE 751BG PIN CONFIGURATIONS 1 VCC PBRST TD TOL GND NC DIP/SO/MicroSO (Top View) 1 NC TD NC TOL ST RESET RESET NC VCC PBRST NC Microprocessor Systems Computers Controllers Portable Equipment Intelligent Instruments Automotive Systems (c) Semiconductor Components Industries, LLC, 2011 PDIP-8 P SUFFIX CASE 646AA ASM1232LP ASM1232LPS-2 ASM1232LPU Features http://onsemi.com ASM1232LPS The ASM1232LP/LPS is a fully integrated microprocessor Supervisor. It can halt and restart a "hung-up" microprocessor, restart a microprocessor after a power failure. It has a watchdog timer and external reset override. A precision temperature-compensated reference and comparator circuits monitor the 5 V, VCC input voltage status. During power-up or when the VCC power supply falls outside selectable tolerance limits, both RESET and RESET become active. When VCC rises above the threshold voltage, the reset signals remain active for an additional 250 ms minimum, allowing the power supply and system microprocessor to stabilize. The trip point tolerance signal, TOL, selects the trip level tolerance to be either 5% or 10%. Each device has both a push-pull, active HIGH reset output and an open drain active LOW reset output. A debounced manual reset input, PBRST, activates the reset outputs for a minimum period of 250 ms. There is a watchdog timer to stop and restart a microprocessor that is "hung-up". The watchdog timeouts periods are selectable: 150 ms, 610 ms and 1200 ms. If the ST input is not strobed LOW before the time-out period expires, a reset is generated. Devices are available in 8-pin DIP, 16-pin SO and compact 8-pin MicroSO packages. NC ST NC RESET NC GND RESET SO (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet. 1 Publication Order Number: ASM1232LP/D ASM1232LP, ASM1232LPS Figure 1. Typical Operating Circuit Figure 2. Block Diagram http://onsemi.com 2 ASM1232LP, ASM1232LPS Table 1. PIN DESCRIPTION Pin # 8-Pin Package Pin # 16-Pin Package Pin Name 1 2 PBRST 2 4 TD Watchdog time delay selection. (tTD = 150 ms for TD = GND, tTD = 610 ms for TD = Open, and tTD = 1200 ms for TD = VCC). 3 6 TOL Selects 5% (TOL connected to GND) or 10% (TOL connected to VCC) trip point tolerance. 4 8 GND Ground. 5 9 RESET Active HIGH reset output. RESET is active: 1. If VCC falls below the reset voltage trip point. 2. If PBRST is LOW. 3. If ST is not strobed LOW before the timeout period set by TD expires. 4. During power-up. 6 11 RESET Active LOW reset output. (See RESET). 7 13 ST Strobe input. 8 15 VCC 5 V power. 1,3,5,7,10,12,14,16 NC No internal connection. Function Debounced manual pushbutton RESET input. Table 2. ABSOLUTE MAXIMUM RATINGS Parameter Min Max Unit Voltage on VCC (Note 1) -0.5 7 V Voltage on ST, TD (Note 1) -0.5 VCC + 0.5 V Voltage on PBRST, RESET, RESET (Note 1) -0.5 VCC + 0.5 V Operating Temperature Range (N suffixed devices) -40 +85 C Operating Temperature Range (others) 0 70 C +260 C +125 C HBM 2 KV MM 200 V Soldering Temperature (for 10 sec) Storage Temperature ESD rating -55 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Voltages are measured with respect to ground http://onsemi.com 3 ASM1232LP, ASM1232LPS Table 3. DC ELECTRICAL CHARACTERISTICS (Unless otherwise stated, 4.5 V VCC 5.5 V and over the operating temperature range of 0C to 70C (-40C to +85C. for N devices). All Voltages are referenced to ground.) Max Unit Supply Voltage VCC 4.5 5.5 V ST and PBRST Input High Level VIH 2 VCC + 0.3 V ST and PBRST Input Low Level VIL -0.3 0.8 V VCC Trip Point (TOL = GND) VCCTP 4.50 4.62 4.74 V VCC Trip Point (TOL = VCC) VCCTP 4.25 4.37 4.49 V Watchdog Timeout Period tTD TD = GND 62.5 150 250 ms Watchdog Timeout Period tTD TD = VCC 500 1200 2000 ms Watchdog Timeout Period tTD TD Floating 250 610 1000 ms Output Voltage VOH I = -500 mA (Note 4) VCC - 0.5 VCC - 0.1 V Output Current IOH Output = 2.4 V (Note 3) -8 -10 mA Output Current IOL Output = 0.4 V 10 Input Leakage IIL (Note 2) -1.0 VOL (Note 4) Parameter RESET Low Level Symbol Internal Pull-up Resistor Conditions Min (Note 2) Typ mA 1.0 mA 0.4 V 40 kW Operating Current (CMOS) ICC1 30 mA Input Capacitance CIN 5 pF COUT 10 pF Output Capacitance PBRST Manual Reset Minimum Low Time tPB Reset Active Time tRST ST Pulse Width tST VCC Fail Detect to RESET or RESET VCC Slew Rate PBRST = VIL ms 20 250 (Note 5) tPDLY VCC Detect to RESET or RESET inactive tRPU tRISE = 5 ms 250 tR 4.25 V to 4.75 V 0 VCC Slew Rate 8 300 PBRST Stable LOW to RESET and RESET Active ms ns 5 4.75 V to 4.25 V 1000 20 tRPD tF 610 ms ms 610 20 ms 1000 ms ns 2. PBRST is internally pulled HIGH to VCC through a nominal 40 kW resistor. 3. RESET is an open drain output. 4. RESET remains within 0.5 V of VCC on power-down until VCC falls below 2 V. RESET remains within 0.5 V of ground on power-down until VCC falls below 2.0 V. 5. Must not exceed the minimum watchdog time-out period (tTD). The watchdog circuit cannot be disabled. To avoid a reset, ST must be strobed. http://onsemi.com 4 ASM1232LP, ASM1232LPS Detailed Description Trip Point Tolerance Selection The ASM1232LP/LPS monitors the microprocessor or micro controller power supply and generates reset signal, both active HIGH and Active LOW, that halt processor operation whenever the power supply voltage levels are outside a predetermined tolerance. The TOL input is used to determine the level VCC can vary below 5 V without asserting a reset. With TOL connected to VCC, RESET and RESET become active whenever VCC falls below 4.5 V. RESET and RESET become active when the VCC falls below 4.75 V if TOL is connected to ground. After VCC has risen above the trip point set by TOL, RESET and RESET remain active for a minimum time period of 250 ms. On power-down, once VCC falls below the reset threshold RESET stays LOW and is guaranteed to be 0.4 V or less until VCC drops below 1.2 V. The active HIGH reset signal is valid down to a VCC level of 1.2 V also. RESET and RESET outputs RESET is an active HIGH signal developed by a CMOS push-pull output stage and is the logical opposite to RESET. RESET is an active LOW signal. It is developed with an open drain driver. A pull up resistor of typical value 10 kW to 50 kW is required to connect with the output. TRIP Point Voltage (V) Tolerance Min Nom Max TOL = VCC 10% 4.25 4.37 4.49 TOL = GND 5% 4.5 4.62 4.74 Tolerance Select Figure 3. Timing Diagram: Power Up Figure 4. Timing Diagram: Power Down http://onsemi.com 5 ASM1232LP, ASM1232LPS Application Information When PBRST is held LOW for the minimum time tPB, both resets become active and remain active for a minimum time period of 250 ms after PBRST returns HIGH. The debounced input is guaranteed to recognize pulses greater than 20 ms. No external pull-up resistor is required, since PBRST is pulled HIGH by an internal 40 kW resistor. The PBRST can be driven from a TTL or CMOS logic line or shorted to ground with a mechanical switch. Manual Reset Operation Push-button switch input, PBRST, allows the user to override the internal trip point detection circuits and issue reset signals. The pushbutton input is debounced and is pulled HIGH through an internal 40 kW resistor. Figure 5. Timing Diagram: Pushbutton Reset Figure 6. Application Circuit: Pushbutton Reset http://onsemi.com 6 ASM1232LP, ASM1232LPS Watchdog Timer and ST Input A watchdog timer stops and restarts a microprocessor that is "hung-up". The mP must toggle the ST input within a set period (as selectable through TD input) to verify proper software execution. If the ST is not toggled low within the minimum timeout period, reset signals become active. In power-up after the supply voltage returns to an in-tolerance condition, the reset signal remains active for 250 ms minimum, allowing the power supply and system microprocessor to stabilize. ST pulses as short as 20 ns can be detected. Figure 7. Timing Diagram: Strobe Input Timeouts periods of approximately 150 ms, 610 ms or 1,200 ms are selected through the TD pin. Watchdog Time-out Period (ms) Min Nom Max GND 62.5 150 250 Floating 250 610 1000 VCC 500 1200 2000 TD Voltage level The watchdog timer cannot be disabled. It must be strobed with a high-to-low transition to avoid watchdog timeout and reset. Figure 8. Application Circuit: Watchdog Timer http://onsemi.com 7 ASM1232LP, ASM1232LPS PACKAGE DIMENSIONS Micro8t/TSSOP8 3x3 CASE 846AA-01 ISSUE O D HE PIN 1 ID NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. 846A-01 OBSOLETE, NEW STANDARD 846A-02. E e b 8 PL 0.08 (0.003) T B M S A DIM A A1 b c D E e L HE S SEATING -T- PLANE 0.038 (0.0015) A A1 MILLIMETERS NOM MAX -- 1.10 0.08 0.15 0.33 0.40 0.18 0.23 3.00 3.10 3.00 3.10 0.65 BSC 0.40 0.55 0.70 4.75 4.90 5.05 MIN -- 0.05 0.25 0.13 2.90 2.90 L c SOLDERING FOOTPRINT* 8X 1.04 0.041 0.38 0.015 3.20 0.126 6X 8X 4.24 0.167 0.65 0.0256 5.28 0.208 SCALE 8:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 8 INCHES NOM -- 0.003 0.013 0.007 0.118 0.118 0.026 BSC 0.016 0.021 0.187 0.193 MIN -- 0.002 0.010 0.005 0.114 0.114 MAX 0.043 0.006 0.016 0.009 0.122 0.122 0.028 0.199 ASM1232LP, ASM1232LPS PACKAGE DIMENSIONS PDIP-8, 300 mils CASE 646AA-01 ISSUE A SYMBOL MIN NOM A E1 5.33 A1 0.38 A2 2.92 3.30 4.95 b 0.36 0.46 0.56 b2 1.14 1.52 1.78 c 0.20 0.25 0.36 D 9.02 9.27 10.16 E 7.62 7.87 8.25 E1 6.10 6.35 7.11 e PIN # 1 IDENTIFICATION MAX 2.54 BSC eB 7.87 L 2.92 10.92 3.30 3.80 D TOP VIEW E A2 A A1 c b2 L e eB b SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. http://onsemi.com 9 ASM1232LP, ASM1232LPS PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD-01 ISSUE O SYMBOL E1 E MIN MAX A 1.35 1.75 A1 0.10 0.25 b 0.33 0.51 c 0.19 0.25 D 4.80 5.00 E 5.80 6.20 E1 3.80 4.00 1.27 BSC e PIN # 1 IDENTIFICATION NOM h 0.25 0.50 L 0.40 1.27 0 8 TOP VIEW D h A1 A c e b L END VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. http://onsemi.com 10 ASM1232LP, ASM1232LPS PACKAGE DIMENSIONS SOIC-16, 150 mils CASE 751BG-01 ISSUE O SYMBOL E1 E MIN NOM MAX A 1.35 1.75 A1 0.10 0.25 b 0.33 0.51 c 0.19 D 9.80 9.90 10.00 E 5.80 6.00 6.20 E1 3.80 3.90 4.00 0.25 1.27 BSC e h 0.25 0.50 L 0.40 1.27 0 8 PIN#1 IDENTIFICATION TOP VIEW D h q A e b A1 c L END VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. http://onsemi.com 11 ASM1232LP, ASM1232LPS Table 4. ORDERING INFORMATION Package Operating Temperature Range Maximum Supply Current (mA) Voltage Monitoring Application Package Marking ASM1232LP 8L PDIP 0C to +70C 30 5V ASM1232LP ASM1232LPN 8L PDIP -40C to +85C 30 5V ASM1232LPN Part Number (Note 6) TIN-LEAD DEVICES ASM1232LPS 16L SOIC 0C to +70C 30 5V ASM1232LPS ASM1232LPS-2 8L SOIC 0C to +70C 30 5V ASM1232LPS-2 ASM1232LPSN 16L SOIC -40C to +85C 30 5V ASM1232LPSN ASM1232LPSN-2 8L SOIC -40C to +85C 30 5V ASM1232LPSN-2 ASM1232LPU 8L MSOP 0C to +70C 30 5V ASM1232LP ASM1232LPUN 8L MSOP -40C to +85C 30 5V ASM1232LPN ASM1232LPF 8L PDIP 0C to +70C 30 5V ASM1232LPF ASM1232LPNF 8L PDIP -40C to +85C 30 5V ASM1232LPNF ASM1232LPS-2F 8L SOIC 0C to +70C 30 5V ASM1232LPS-2F ASM1232LPSF 16L SOIC 0C to +70C 30 5V ASM1232LPSF ASM1232LPSN-2F 8L SOIC -40C to +85C 30 5V ASM1232LPSN-2F ASM1232LPSNF 16L SOIC -40C to +85C 30 5V ASM1232LPSNF ASM1232LPUF 8L MSOP 0C to +70C 30 5V ASM1232LPF ASM1232LPUNF 8L MSOP -40C to +85C 30 5V ASM1232LPNF LEAD FREE DEVICES 6. For parts to be packed in Tape and Reel, add "-T" at the end of the part number. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 12 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative ASM1232LP/D