AC-DC 5-30 Watts ECL Series xppower.com * Ultra Compact Size * Single, Dual & Triple Outputs * Open Frame PCB & Chassis Mount * Encapsulated PCB Mount Versions * <0.3 W No Load Input Power * Peak Load Capability * 3 Year Warranty Specification Input * 85-264 VAC (120-370 VDC) * 47-63 Hz * ECL05: 0.1 A rms, ECL10: 0.2 A rms ECL15: 0.3 A rms, ECL25: 0.4 A rms ECL30: 0.8 A rms at 230 VAC Inrush Current * 20 A at 115 VAC, 40 A at 230 VAC, cold start at 25 C Earth Leakage Current * Class II construction no earth Power Factor * EN61000-3-2, class A No Load Input Power * <0.3 W Input Protection * ECL05/10: Internal T1 A/250 VAC fuse ECL15/25/30: Internal T2 A/250 VAC fuse Input Voltage Input Frequency Input Current Output * See tables * 5% on output 1 only, on multiple output versions, V2 & V3 will track by same percentage, (not `-E' or `-S' versions) Initial Set Accuracy * 1% for output 1, 1% for output 2 of UD01 & UD02 versions, 5% for output 2 & output 3 of other versions Minimum Load * Single output versions: none, Multi output versions: UD01 & UD02: 10% V1 & V2 UD03: 10% V1, 20% V2 UT02 & UT03: 10% V1, 20% V2 & V3 to meet regulation specifications Start Up Delay * 3 s max Start Up Rise Time * 14 ms max Hold Up Time * 16 ms typical for single output versions, 12 ms typical for multiple output versions, at full load & 115 VAC Line Regulation * 0.5% max for single output versions and output 1 of multiple output versions, 0.9% max for output 2 & output 3 of multiple output versions Load Regulation * 1% max for single output versions, for multiple output versions (see note 5) Cross Regulation * Multi output versions only (see note 5) Transient Response * 4% max deviation, recovery to within 1% in 500 s for a 25% load change Ripple & Noise * Single output versions: 3.3-5 V versions: 50 mV pk-pk, 12-15 V versions: 120 mV pk-pk, 24-48 V versions: 200 mV pk-pk, Multiple output versions: 1% pk-pk on any output, 20 MHz bandwidth Overvoltage Protection * 115-140% Vnom, 195-216% Vnom ECL05/10/15/25 with 3.3 V Overload Protection * Single output versions: ECL05/10/15: 120-150%, ECL25: 120-170% of total power Multiple output versions: 140-200% of total power Short Circuit Protection * Trip and restart (hiccup mode) Temperature * 0.05%/C Coefficient Output Voltage Output Voltage Trim General Efficiency Isolation Switching Frequency Power Density MTBF * * * * See tables 3000 VAC Input to Output 70 kHz typical ECL05: 2.25 W/In3 (PCB Mount version) ECL10: 5.50 W/In3 (PCB Mount version) ECL15: 5.30 W/In3 (PCB Mount version) ECL25: 5.90 W/In3 (PCB Mount version) ECL30: 7.10 W/In3 (PCB Mount version) * ECL05/10: >450 kHrs, ECL15/25/30: >400 kHrs, to MIL-HDBK-217F at 25 C, GB Environmental Operating Temperature * -20 C to +70 C, derate linearly from 100% at +50 C to 50% at +70 C Cooling * Convection-cooled Operating Humidity * 95% RH, non-condensing Storage Temperature * -40 C to +85 C Operating Altitude * 3000 m Vibration * 2 g, 10 Hz to 500 Hz, 10 mins/cycle, 60 mins each cycle EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity * * * * * EFT/Burst Surge * * Conducted Immunity Magnetic Fields Dips & Interruptions * * * Safety Approvals * EN55022, level B conducted & radiated EN61000-3-2, class A EN61000-3-3 EN61000-4-2, level 3 Perf Criteria A EN61000-4-3, 10 V/m 80% mod Perf Criteria A EN61000-4-4, level 3, Perf Criteria A EN61000-4-5, installation class 3, Perf Criteria A EN61000-4-6, 10 Vrms Perf Criteria A EN61000-4-8, 10 A/m, Perf Criteria A EN61000-4-11, 30% for 10 ms, 60% for 100 ms, 100% for 5000 ms Perf Criteria A, B, B IEC60950-1, EN60950-1, UL60950-1, CSA22.2 No. 234 per cUL Output Power Output Current Output Voltage 4.3 W 5.0 W 5.0 W 5.0 W 5.0 W 5.0 W 5.0 W 8.6 W 10.0 W 10.0 W 10.0 W 10.0 W 10.0 W 10.0 W Nominal 1.30 A 1.00 A 0.55 A 0.41 A 0.33 A 0.21 A 0.10 A 2.60 A 2.00 A 1.10 A 0.83 A 0.67 A 0.42 A 0.21 A 3.3 VDC 5.0 VDC 9.0 VDC 12.0 VDC 15.0 VDC 24.0 VDC 48.0 VDC 3.3 VDC 5.0 VDC 9.0 VDC 12.0 VDC 15.0 VDC 24.0 VDC 48.0 VDC Peak(1) 1.69 A 1.30 A 0.71 A 0.54 A 0.44 A 0.27 A 0.13 A 3.38 A 2.60 A 1.43 A 1.08 A 0.87 A 0.55 A 0.27 A Efficiency Model Number(2) 72% 75% 78% 78% 80% 82% 82% 72% 75% 78% 78% 80% 82% 82% ECL05US03 ECL05US05 ECL05US09 ECL05US12 ECL05US15 ECL05US24 ECL05US48 ECL10US03 ECL10US05 ECL10US09 ECL10US12 ECL10US15 ECL10US24 ECL10US48 Notes 1. Peak load lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal. 2. Add suffix to model number to define type: mount, add `-T' for chassis mount, add `-E' for encapsulated. O add `-P' for PCB (-P) Mechanical Details Open Frame - PCB Mount (-P) 0.80 (20.3) (-P) Encapsulated (-E) (-E) (-P) 1.95 (49.5) 0.075 (1.91) -Vo ACL V Adj. 0.10 (2.5) 0 0.075 (1.91) 0.91 (23.0) (-E) +Vo ACN 1.00 (25.4) (-E) 0.40 (10.1) 4 x o 0.04 (o1.0) 1.80 (45.7) 0.39 (10.0) 1.07 (27.2) 0.90 (22.9) 0 0.15 (3.8) 0.80 0.01 (20.32 0.3) 0.13 (3.4) 0.73 (18.5) ACL o 0.07 (o1.8) 1.80 0.01 (45.72 0.3) 0.17 (4.4) (-T) o 0.04 (o1.0) 2.06 (52.4) Open Frame - Chassis Mount (-T) T T ACN TOP VIEW -Vo +Vo 2.56 (65.0) 4-o0.126 (o3.20) V 1.00 (25.4) 0.15 (4.0) ACL 0.14 (3.5) 0.40 0.01 (10.16 0.3) +Vo -Vo ACN 0.68 (17.4) 0.13 (3.40) 2.28 (58.0) 0.73 (18.5) V Adj. 0.85 (21.6) Notes 1. All dimensions in inches (mm). 2. Weight: ECL05/10 P Version: 0.057 lbs (26 g) ECL05/10 T Version: 0.057 lbs (26 g) ECL05/10 E Version: 0.13 lbs (60 g) 3. Tolerances: x.xx = 0.02 (x.x = 0.5) x.xxx = 0.01 (x.xx = 0.25) Mating Connectors (-T version only) Input Connector: JST PHR-3 Output Connector: JST PHR-2 Crimps: SPH-002T-P0.5S Cable harness with 300 mm wire available, order part no. ECL10 LOOM KIT AC-DC ECL05/10 Models and Ratings AC-DC ECL15 Models and Ratings Output Power 10 W 15 W 15 W 15 W 15 W 15 W 15 W Output Current Output Voltage 3.3 VDC 5.0 VDC 9.0 VDC 12.0 VDC 15.0 VDC 24.0 VDC 48.0 VDC Nominal 3.00 A 3.00 A 1.67 A 1.25 A 1.00 A 0.63 A 0.32 A Peak(1) 3.90 A 3.90 A 2.17 A 1.62 A 1.30 A 0.82 A 0.41 A Efficiency Model Number(2,3) 75% 78% 80% 80% 80% 82% 82% ECL15US03 ECL15US05 ECL15US09 ECL15US12 ECL15US15 ECL15US24 ECL15US48 Notes 1. Peak load lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal. 2. Add suffix to model number to define type: add `-P' for PCB mount, add `-T' for chassis mount, add `-E' for encapsulated, add `-S' for screw terminals. 3. A screw terminal version (-S) is available with DIN clip attached, add suffix `D', e.g. ECL15US24-SD, DIN rail mounting kit is available as a separate item, order code ECL15 DIN CLIP. 4. For medically-approved 15 W power supplies contact sales or see www.xppower.com for details of CU15-M series and VCP15 series. Mechanical Details Open Frame - PCB Mount (-P) Encapsulated (-E) 0.50 (12.6) 2.44 (62.0) -Vo -Vo ACN 1.21 (30.7) +Vo 0.69 (17.5) ACL 2.13 (54.1) 0.21 (5.4) 0.96 (24.4) 0.78 (20.0) max 4x o 0.04 (o1.0) o 0.07 (o1.8) o 0.04 (o1.0) 0.39 (10.0) Open Frame - Chassis Mount (-T) Screw Terminal (-S) 3.10 (78.7) 2.95 (75.0) 4-0.12 (3.2) 1.36 (34.5) -Vo 0.95 ACN (24.1) ACL 1.25 (31.7) 0.79 (20.1) 2.56 (65.0) 0.36 (9.1) 0.17 (4.4) 0.15 (3.8) +Vo ACL 0.69 (17.5) 2.13 (54.1) 0.11 (2.9) TOP VIEW V Adj. 0.15 (3.9) 0.06 (1.6) 1.31 (33.3) 0.79 (20.1) ACN +Vo TOP VIEW ACN 1.00 ACL (25.4) 4x o 0.14 (4x o 3.5) -Vo +Vo 0.44 (11.1) 0.15 (3.8) 0.15 (3.8) 2.80 (71.1) V Adj. 2.54 (64.5) 0.39 (10.0) 1 0.78 (20.0) max 0.91 (23.1) 1.04 (26.4) 0.27 0.09 (6.8) (2.5) 3.30 (84.0) Optional DIN clip Notes 1. All dimensions in inches (mm). 2. Weight: ECL15 P Version: 0.07 lbs (35 g) T Version: 0.07 lbs (35 g) E Version: 0.20 lbs (90 g) S Version: 0.24 lbs (110 g) 3. Tolerances: x.xx = 0.02 (x.x = 0.5) x.xxx = 0.01 (x.xx = 0.25) Mating Connectors (-T version only) Input Connector: JST PHR-3 Output Connector: JST PHR-4 Crimps: SPH-002T-P0.5S Cable harness with 300 mm wire available, order part no. ECL15 LOOM KIT Output 1 Voltage Current(2) +12.0 V 0.65 A +15.0 V 0.50 A 5.0 V(1) 1.50 A 5.0 V(1) 2.00 A 5.0 V(1) 2.00 A Output Power 15 W 15 W 15 W 15 W 15 W Output 2 Voltage Current(2) -12.0 V 0.650 A -15.0 V 0.500 A 12.0 V(1) 0.625 A +12.0 V 0.200 A +15.0 V 0.150 A Voltage Output 3 Current(2) -12.0 V -15.0 V Efficiency 82% 82% 81% 81% 81% 0.200 A 0.150 A Model Number(3,4) ECL15UD01 ECL15UD02 ECL15UD03 ECL15UT02 ECL15UT03 Notes 5. UD01/UD02: Load regulation <3%, 10-100% load. Cross regulation <3%, one output fixed, the other varied from 10-100% load Load regulation <1% V1, <10% V2 UD03: Cross regulation <10% V2, V1 varied from 10-100% load UT02/UT03: Load regulation <1% V1, <10% V2 & V3 Cross regulation <10% V2 & V3, V2 & V3 at 50% load & V1 varied from 20-100% load 1. Isolated output 2. Peak load of 130% lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal. 3. Add suffix to model number to define type: add `-P' for PCB mount, add `-T' for chassis mount, add `-E' for encapsulated, add `-S' for screw terminals. 4. A screw terminal version (-S) is available with DIN clip attached, add suffix `D' e.g. ECL15UT02-SD, DIN rail mounting kit is available as a separate item, order code ECL15 DIN CLIP. Mechanical Details Open Frame - PCB Mount (-P) 2.44 (62.0) 0.79 (20.0) max Pin1 Pin2 0.155 (3.9) 2.13 (54.1) 0.25 (6.3) Pin5 0.29 (7.4) ACL 0.17 (4.4) 0.29 (7.4) 0.25 (6.3) Pin4 VAdj 0.15 (3.8) Pin3 0.07 (1.8) 0.96 (17.5) 0.06 (1.6) 1.20 (30.7) ACN 7 Pin 1 2 3 4 5 UD01/02 V2 NP COM V1 NP UD03 NP V2 RTN V2 V1 V1 RTN UT02/03 V3 COM V2 V1 V1 RTN UD03 NC V2 RTN V2 V1 V1 RTN UT02/03 V3 COM V2 V1 V1 RTN 7-o0.04 (o1.0) NP = No pin. 7-o0.07 (o1.8) Open Frame - Chassis Mount (-T) Pin 1 2 3 4 5 0.15 (3.81) 0 1.25 (31.8) ACL 0.95 (24.1) NP 0.15 (3.8) Pin1 Pin2 Pin3 Pin4 Pin5 ACN 0.79 (20.0)Max A 0.91 (23.1) 4-o0.13 (o3.20) A NC = No connection. VAdj 2.80 (71.1) UD01/02 V2 COM COM COM V1 3.10 (78.7) Encapsulated (-E) Pin3 Pin4 A ACL Pin5 4-o0.04 (o1.0) 0.54 (13.7) C1 0.21 (5.4) 2-o0.14 (o3.5) 1.03 (26.3) Pin4 ACL 0.44 (11.2) Pin5 1.04 (26.4) Pin3 0.10 (2.5) 2.56 (65.1) 0.18 (4.5) 0.10 (2.5) P 0.10 (2.5) UT02/03 V3 COM V2 V1 V1 RTN UD03 NC V2 RTN V2 +V1 V1 RTN UT02/03 V3 COM V2 V1 V1 RTN 0.39 (10.0) 1.36 (34.5) Top View 1.18 (30.0) Pin2 UD03 NP V2 RTN V2 V1 V1 RTN 4 Pin1 2 ACN A UD01/02 V2 NP COM V1 NP NP = No pin. 2.13 (54.1) Screw Terminal (-S) 0.18 (4.6) Pin 1 2 3 4 5 0.96 (24.4) T View Top Pin2 1.31 (33.5) 0.12 (3.1) 0 0.69 (17.5) ACN Pin1 0.25 (6.3) 2 0.39 (10.0) 0.25 (6.3) 0.54 (13.7) 2.56 (65.0) 0.27 (6.8) Optional DIN clip Pin 1 2 3 4 5 UD01/02 V2 COM COM COM V1 NC = No connection. 2.95 (75.0) 3.31 (84.0) Notes 1. All dimensions in inches (mm). 2. Tolerances: x.xx = 0.02 (x.x = 0.5) x.xxx = 0.01 (x.xx = 0.25) 3. Weight: ECL15 UD/UT: P Version: 0.09 lbs (40 g) T Version: 0.09 lbs (40 g) E Version: 0.21 lbs(95 g) S Version: 0.26 lbs (120 g) Mating Connectors (-T version only) Input Connector: JST PHR-3 Output Connector: JST XHP-5 AC-DC ECL15UD/UT Models and Ratings AC-DC ECL25 Models and Ratings Output Power 20 W 25 W 25 W 25 W 25 W 25 W 25 W Output Current Output Voltage 3.3 VDC 5.0 VDC 9.0 VDC 12.0 VDC 15.0 VDC 24.0 VDC 48.0 VDC Nominal 6.00 A 5.00 A 2.80 A 2.10 A 1.67 A 1.04 A 0.52 A Peak(1) 7.80 A 6.50 A 3.64 A 2.73 A 2.17 A 1.35 A 0.68 A Efficiency Model Number(2,3) 75% 78% 80% 80% 80% 82% 82% ECL25US03 ECL25US05 ECL25US09 ECL25US12 ECL25US15 ECL25US24 ECL25US48 Notes 1. Peak load lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal. 2. Add suffix to model number to define type: add `-P' for PCB mount, add `-T' for chassis mount, add `-E' for encapsulated, add `-S' for screw terminals. 3. A screw terminal version (-S) is available with DIN clip attached, add suffix `D', e.g. ECL25US24-SD, DIN rail mounting kit is available as a separate item, order code ECL25/30 DIN CLIP. Mechanical Details (-P) (-P) Open Frame - PCB Mount (-P) EncapsulatedE E(-E) 2.96 (75.2) 0.125 (3.2) ACN ACN -Vo 1.18 (30.0) 1.36 (34.6) (-E) (-E) 3.10 (78.7) ACL 1.18 (30.0) 0.59 (15.0) +Vo 0.59 (15.0) TOP VIEW -Vo 0.16 (4.1) +Vo ACL 0.09 (2.3) 0 0.15 (3.8) 0.17 (4.4) 2.85 (72.4) 0.05 (1.4) V Adj. 1.50 (38.1) 2.85 (72.4) 0.09 (2.3) 0.88 (22.3) MAX 1 1.10 (27.9) 4x o 0.039 (o1.0) o0.04 (o1.0) 0.39 (10.0) o0.07 (o 1.8) Open Frame - Chassis Mount (-T) Screw Terminal (-S) 3.46 (87.9) 3.43 (87.0) 4- 0.15 (3.81) 0.44 (11.2) -Vo 1.10 ACN 1.36 (34.6) (27.9) ACL TOP VIEW ACN +Vo ACL 1.57 (40.0) 0.13 (3.3) 0.13 (3.3) 3.20 (81.3) 0.88 (22.4) MAX (-S) (-S) 4x o0.14 (4x o3.5) -Vo 0.84 (21.3) 1.20 +Vo (30.5) V Adj. 3.01 (76.4) 0.39 (10.0) 1.00 (25.4) 1 1.12 (28.5) 0.27 (6.8) 0.10 (2.5) 3.78 (96.0) Optional DIN clip Notes 1. All dimensions in inches (mm). 2. Weight: ECL25: P Version: 0.14 lbs (66 g) T Version: 0.14 lbs (66 g) E Version: 0.33 lbs (150 g) S Version: 0.37 lbs (170 g) 3. Tolerances: x.xx = 0.02 (x.x = 0.5) x.xxx = 0.01 (x.xx = 0.25) Mating Connectors (-T version only) Input Connector: JST XHP-3 Output Connector: JST XHP-6 Crimps: SXH-002T-P0.6 Cable harness with 300 mm wire available, order part no. ECL25 LOOM KIT Output 1 Voltage Current(2) +12.0 V 1.3 A +15.0 V 1.0 A 5.0 V(1) 3.0 A 5.0 V(1) 3.0 A 5.0 V(1) 3.0 A Output Power 30 W 30 W 30 W 30 W 30 W Output 2 Voltage Current(2) -12.0 V 1.30 A -15.0 V 1.00 A 12.0 V(1) 1.30 A +12.0 V 0.63 A +15.0 V 0.50 A Voltage Output 3 Current(2) -12.0 V -15.0 V 0.63 A 0.50 A Efficiency 84% 83% 81% 83% 81% Model Number(3,4) ECL30UD01 ECL30UD02 ECL30UD03 ECL30UT02 ECL30UT03 Notes 1. Isolated output 2. Peak load of 130% lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal. 3. Add suffix to model number to define type: add `-P' for PCB mount, add `-T' for chassis mount, add `-E' for encapsulated, add `-S' for screw terminals. 4. A screw terminal version (-S) is available with DIN clip attached, add suffix `D' e.g. ECL30UT02-SD, DIN rail mounting kit is available as a separate item, order code ECL25/30 DIN CLIP. 5. UD01/UD02: Load regulation <3%, 10-100% load. Cross regulation <3%, one output fixed, the other varied from 10-100% load Load regulation <1% V1, <10% V2 UD03: Cross regulation <10% V2, V1 varied from 10-100% load UT02/UT03: Load regulation <1% V1, <10% V2 & V3 Cross regulation <10% V2 & V3, V2 & V3 at 50% load & V1 varied from 20-100% load Mechanical Details Open Frame - PCB Mount (-P) 2 2.96 (75.2) Vadj Pin 1 2 3 4 5 0.29 (7.5) Pin5 0.09 (2.3) 0.09 (2.3) 0.05 (1.4) 2.85 (72.4) 0.29 (7.5) 1.05 (26.7) 0.29 (7.5) 0.15 (3.8) Pin4 ACL 0.29 (7.5) 1 1.18 (29.9) Pin3 0.17 (4.4) Pin2 ACN 1.36 (34.6) 0.88 (22.3) Max Pin1 o 0.04 (o1.0) UD01/02 NP NP V2 COM V1 UD03 V1 RTN V1 NP V2 RTN V2 UT02/03 -V1 +V1 V3 COM V2 UD03 V1 RTN V1 NC V2 RTN V2 UT02/03 -V1 +V1 V3 COM V2 NP = No pin. o 0.07(o1.8) Open Frame - Chassis Mount (-T) 3.46 (87.9) Pin 1 2 3 4 5 3.20 (81.3) UD01/02 V2 COM COM COM V1 NC = No connection. 0.12 (3.0) ACL 1.00 (25.4) NP 1.36 (34.6) Pin1 Pin2 P Pin3 Pin4 Pin5 ACN 0.88 (22.4) Max 4-o0.15 (o3.8) 1.10 (27.9) Vadj 0.13 (3.3) 0.13 (3.3) Encapsulated (-E) P Pin4 Pin 1 2 3 4 5 1.10 (28.0) 0.39 (10.0) Pin3 1.50 (38.1) 0.16 (4.1) 1.18 (29.9) Pin2 Top View 0.59 (14.9) ACN 0.59 (14.9) 0.29 (7.5) 0.29 (7.5) 0 Pin1 Pin5 ACL 7-o0.04 (o1.00) 0.12 (3.2) UD01/02 NP NP V2 COM V1 UD03 V1 RTN V1 NP V2 RTN V2 UT02/03 -V1 +V1 V3 COM V2 UD03 V1 RTN V1 NC V2 RTN V2 UT02/03 -V1 +V1 V3 COM V2 NP = No pin. C0.04 (1.0) 2.85 (72.4) 3.10 (78.7) Screw Terminal (-S) 0.19 (4.8) 2-o0.14(o3.5) 0.39 (10.0) 0 Pin4 T 1.12 (28.5) 0.10 (2.5) Pin5 Optional DIN clip 0.10 (4.5) 3.03 (77.0) 0.18 (4.5) 1.39 (35.2) Pin3 3.43 (87.0) 0.27 (6.8) 0.10 (4.5) 0.44 (11.2) ACL Top View 1.57 (40.0) Pin2 ACN 1.21 (30.7) Pin1 Pin 1 2 3 4 5 UD01/02 V2 COM COM COM V1 NC = No connection. 3.78 (96.0) Notes 1. All dimensions in inches (mm). 2. Tolerances: x.xx = 0.02 (x.x = 0.5) x.xxx = 0.01 (x.xx = 0.25) 3. Weight: ECL30 UD/UT: P Version: 0.13 lbs (60 g) T Version: 0.13 lbs (60 g) E Version: 0.34 lbs (155 g) S Version: 0.39 lbs (175 g) Mating Connectors (-T version only) Input Connector: JST XHP-3 Output Connector: JST XHP-5 15 Jan 19 AC-DC ECL30UD/UT Models and Ratings