austriamicrosystems AG is now ams AG The technical content of this austriamicrosystems datasheet is still valid. Contact information: Headquarters: ams AG Tobelbaderstrasse 30 8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 e-Mail: ams_sales@ams.com Please visit our website at www.ams.com Data sheet AS1337 2 0 0 m A , D C - D C St e p - U p C o n v e r t e r w i t h B u c k M o d e 1 General Description 2 Key Features Low Start-Up Voltage: 0.85V Output Voltage Range: 2.5V to 5.0V Delivers 200mA @ 3.3V (from two AA Cell) up to 97% Efficiency The AS1337A offers a shutdown mode where the battery is connected directly to the output enabling the supply of realtime-clocks or memories. Single-Cell Operation am lc s on A te G nt st il Internal PMOS Synchronous Rectifier In the shutdown mode of the AS1337B the battery is disconnected and the output is discharged. Table 1. Standard Products Model lv High-Speed Fixed-Frequency: 1.2MHz al id Input Voltage Range: 0.65V to 4.5V The AS1337 is a synchronous, fixed frequency, highefficiency DC-DC boost converter capable of supplying 3.3V @ 200mA from two AA Cells. Compact size and minimum external parts requirements make these devices perfect for modern portable devices. The AS1337 offers automatic powersave mode to increase efficiency at light loads. For input voltages higher than VOUT the AS1337 will switch in a step down mode, so that a Buck Boost function is realized. Automatic Powersave Operation Anti-Ringing Control Minimizes EMI Logic Controlled Shutdown (< 1A) Operation Mode TDFN (3x3mm) 8-pin Package AS1337A Battery Connected in Shutdown AS1337B Battery Disconnected in Shutdown and Output Discharged 3 Applications The AS1337 offers a POK (open-drain) feature which detects output power fail of 10%. The AS1337 is ideal for low-power applications where ultrasmall size is critical as in medical diagnostic equipment, handheld instruments, pagers, digital cameras, remote wireless transmitters, MP3 players, LCD bias supplies, cordless phones, GPS receivers, and PC cards. ca The AS1337 is available in a TDFN (3x3mm) 8-pin package. ch 3.6V ni Figure 1. AS1337 - Typical Application Diagram - Dual Cell to 3.3V Synchronous Boost Converter Buck Mode Te 2x AA Cell Range VOUT=3.3V VIN Curve L1 4.7H VOUT LX VIN = 2xAA 1.6V to 3.6V VIN CIN 10F Boost Mode VOUT = 3.3V On Off EN GND AS1337 COUT 22F FB POK PGND 1.6V www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 1 - 15 AS1337 Datasheet - P i n A s s i g n m e n t s 4 Pin Assignments Figure 2. Pin Assignments (Top View) 8 FB LX 2 7 VIN AS1337 PGND 3 9 GND 5 EN Pin Descriptions Table 2. Pin Descriptions am lc s on A te G nt st il lv GND 4 6 POK al id VOUT 1 Pin Name Pin Number VOUT 1 2 LX PGND GND 5 EN 6 ca POK 8 9 Te ch GND 7 ni VIN FB 3 4 Description Output Voltage. Bias is derived from VOUT when VOUT exceeds VIN. PCB trace length from VOUT to the output filter capacitor(s) should be as short and wide as is practical. Switch Pin. Connect an inductor between this pin and VIN. Keep the PCB trace lengths as short and wide as is practical to reduce EMI and voltage overshoot. If the inductor current falls to zero, or pin EN is low, an internal 100 anti-ringing switch is connected from this pin to VIN to minimize EMI. Note: An optional Schottky diode can be connected between this pin and VOUT. Power Ground. Provide a short, direct PCB path between this pin and the output capacitor(s). Ground Enable Pin. Logic controlled enable input. 1 = Normal operation 0 = Shutdown Note: In a typical application, EN should be connected to VIN through a 1M pull-up resistor. POK. High when VOUT is within regulation. Input Voltage. The AS1337 gets its start-up bias from VIN unless VOUT exceeds VIN, in which case the bias is derived from VOUT. Thus, once started, operation is completely independent from VIN. Operation is only limited by the output power level and the internal series resistance of the supply. Feedback Pin. Feedback input to the gm error amplifier. Connect a resistor divider tap to this pin. The output voltage can be adjusted from 2.5V to 5V by: VOUT = 1.23V[1 + (R1/R2)] Exposed Pad Ground www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 2 - 15 AS1337 Datasheet - A b s o l u t e M a x i m u m R a t i n g s 5 Absolute Maximum Ratings Stresses beyond those listed in Table 3 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Section 6 Electrical Characteristics on page 4 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 3. Absolute Maximum Ratings Max Units VIN to GND -0.3 5.5 V FB to GND -0.3 5 V All other pins to GND -0.3 6 V Input Current (latch-up immunity) -100 100 mA Norm: JEDEC 78 kV Norm: MIL 883 E method 3015 Electrical Parameters Electrostatic Discharge Human Body Model am lc s on A te G nt st il 2 Notes al id Min lv Parameter Temperature Ranges and Storage Conditions Storage Temperature Range -55 +150 Package Body Temperature Humidity non-condensing +260 C 85 % 1 The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/ JEDEC J-STD-020 "Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices". The lead finish for Pb-free leaded packages is matte tin (100% Sn). Represents a max. floor life time of unlimited Te ch ni ca Moisture Sensitive Level 5 C www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 3 - 15 AS1337 Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s 6 Electrical Characteristics VIN = VEN = +1.2V, VOUT = +3.3V, Typ values @ TAMB = +25C (unless otherwise specified); Table 4. Electrical Characteristics TAMB Parameter Conditions Operating Temperature Range Min Typ -45 Input ILOAD = 1mA Minimum Operating Voltage EN = VIN 0.85 0.85 V 4.5 V 5 V 1.268 V nA 1 0.65 VFB Feedback Voltage IFB Feedback Input Current 1.192 VFB = 1.25V Quiescent Current VFB = 1.4V ISHDN Shutdown Current EN = GND, VIN = 3.3V 20 35 A 0.01 1 A 0.01 1 A AS1337B only 0.01 1 A VOUT = 3.3V 0.35 VOUT = 5V 0.20 VOUT = 3.3V 0.45 VOUT = 5V 0.30 INMOSSWL NMOS Switch Leakage IPMOSSWL PMOS Switch Leakage RONNMOS NMOS Switch On Resistance RONPMOS PMOS Switch On Resistance NMOS Current Limit Max Duty Cycle fSW IEN mA 80 87 % 0.95 1.2 1.5 0.3 MHz V EN Input Current EN = 5.0V 0.01 1 A POK Voltage Low IPOK=1mA 0.1 0.4 V POK Leakage Current VPOK = VIN or VOUT 1 100 nA Power-OK Threshold Falling Edge 88 91 % ch Power-OK ca VIL 850 1 Enable Input Threshold ni VIH VFB = 1V Switching Frequency Shutdown 1.23 1 2 IQPWS lv 2.5 Regulation INMOS C V Output Voltage Adjust Range Switches +85 1.15 Maximum Input Voltage Operating Current Units am lc s on A te G nt st il VIN Minimum Start-Up Voltage Max al id Symbol 86 Te Thermal Protection TENM TENM Overtemperature Protection 145 C Overtemperature Protection Hysteresis 10 C 1. Minimum VIN operation after start-up is only limited by the battery's ability to provide the necessary power as it enters a deeply discharged state. 2. IQPWS is measured at VOUT. Multiply this value by VOUT/VIN to get the equivalent input (battery) current. Note: All limits are guaranteed. The parameters with min and max values are guaranteed with production tests or SQC (Statistical Quality Control) methods. www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 4 - 15 AS1337 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s 7 Typical Operating Characteristics VOUT = 3.3V, CIN = 10F, COUT = 22F, L1 = 4.7H, TAMB = +25C (unless otherwise specified). 100 90 90 80 80 60 50 70 60 lv 70 al id Figure 4. Efficiency vs. IOUT - Step-up Mode 100 Efficiency (%) Efficiency (%) Figure 3. Efficiency vs. IOUT - Down Conversion Mode 50 Vin = 1.5V Vin = 3.5V 40 Vin = 4.0V 30 Vin = 2.0V am lc s on A te G nt st il 40 Vin = 3.0V 30 0.1 1 10 100 1000 0.1 1 Output Current (mA) Figure 5. Efficiency vs. Input Voltage 100 1000 Figure 6. Output Current vs. Input Voltage 70 60 Output Current (mA) 80 Iout = 1mA 50 Iout = 10mA Iout = 30mA 40 400 300 200 100 Iout = 100mA Iout = 200mA 30 0.5 1.0 1.5 ca Efficiency (%) 100 500 90 2.0 2.5 3.0 3.5 4.0 0 4.5 0.5 1 1.5 Input Voltage (V) Switching Frequency (MHz) ch Te 0.65 0.55 0.45 0 15 30 45 3 3.5 4 4.5 75 90 1.5 0.75 0.35 -45 -30 -15 2.5 Figure 8. Switching Frequency vs. Temperature ni 0.85 2 Input Voltage (V) Figure 7. Min. Operating Voltage vs. Temperature Minimum Operating Voltage (V) 10 Output Current (mA) 60 75 90 1.4 1.3 1.2 1.1 1 0.9 -45 -30 -15 Temperature (C) www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 0 15 30 45 60 Temperature (C) Revision 1.05 5 - 15 AS1337 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s Figure 9. Output Voltage vs. Temp.; ILOAD = 1mA Figure 10. Load Transient Response; VIN = 1.8V 3.5 100mV/Div VOUT 3.4 3.35 100mA 3.25 al id 3.3 IOUT 10mA 3.2 15 30 45 60 75 90 1ms/Div am lc s on A te G nt st il 10mA IOUT 100mA VOUT IOUT VOUT Figure 12. Load Transient Response; VIN = 3.6V 100mV/Div Figure 11. Load Transient Response; VIN = 3.0V 1ms/Div Te ch ni ca 1ms/Div 100mV/Div 0 Temperature (C) 100mA 3.1 -45 -30 -15 lv 3.15 10mA Output Voltage (V) 3.45 www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 6 - 15 AS1337 Datasheet - D e t a i l e d D e s c r i p t i o n 8 Detailed Description The AS1337 can operate from a single-cell input voltage (VIN) below 1V, and features fixed frequency (1.2MHz) and current mode PWM control for exceptional line- and load-regulation. With low RDS(ON) and gate charge internal NMOS and PMOS switches, the device maintains high-efficiency from light to heavy loads. al id Modern portable devices frequently spend extended time in low-power or standby modes, switching to high power-drain only when certain functions are enabled. The AS1337 is ideal for portable devices since it maintains high-power conversion efficiency over a wide output power range, thus increasing battery life in these types of applications. In addition to high-efficiency at moderate and heavy loads, the AS1337 includes an automatic powersave mode that improves efficiency of the power converter at light loads. The powersave mode is initiated if the output load current falls below a factory programmed threshold. The Overtemperature protection circuitry turn-off both switches for a short time when the temperature reaches 145C in the device . L1 4.7H POK 1.5V Single Cell 7 VIN CIN 1F 2 LX am lc s on A te G nt st il 6 Start Up OSC A B PWM Control 1.2MHz Ramp Generator Slope Compensator + PWM - Comp - EN Shutdown Control Powersave Operation Control 3.3V Output VOUT 0.45 0.35 CFF* Current Sense 8 - gm Error Amp + R1 560k COUT 4.7F FB CP2 2.5pF 1.23V Ref R2 330k AS1337 4 GND 3 PGND Te ch * Optional RC 80k CC 150pF 1 ni ca Powersave Shutdown 2.3V - VOUT Good + A/B MUX Sync Drive Control 5 lv Figure 13. AS1337 - Block Diagram www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 7 - 15 AS1337 Datasheet - D e t a i l e d D e s c r i p t i o n Low-Voltage Start-Up and Soft Start The AS1337 requires a VIN of only 0.85V (typ) or higher to start up. The low-voltage start-up circuitry controls the internal switches and provides a soft start function, where the inductor current during start up is limited for a certain time. This soft start and in rush current limitation feature provides also a smooth curve of VOUT after start up and makes the overshoot of VOUT minimal. To achieve this, a 100pF capacitor as CFF is needed (see Figure 13 on page 7) to speed up the feedback loop. Low-Noise Fixed-Frequency Operation Oscillator The AS1337 switching frequency is internally fixed at 1.2MHz allowing the use of very small external components. Current Sensing al id After a certain time a bigger inductor current is allowed and the soft start is disabled. lv A signal representing the internal NMOS-switch current is summed with the slope compensator. The summed signal is compared to the error amplifier output to provide a peak current control command for the PWM. Peak switch current is limited to approximately 850mA independent of VIN or VOUT. am lc s on A te G nt st il Zero Current Comparator The zero current comparator monitors the inductor current to the output and shuts off the PMOS synchronous rectifier once this current drops to 20mA (approx.). This prevents the inductor current from reversing polarity and results in improved converter efficiency at light loads. Anti-Ringing Control Anti-ringing control circuitry prevents high-frequency ringing on pin LX as the inductor current approaches zero. This is accomplished by damping the resonant circuit formed by the inductor and the capacitance on pin LX. Setting Output Voltage A voltage divider from VOUT to GND programs the output voltage from 2.5V to 5V via pin FB as: VOUT = 1.23V(1 + (R1/R2)) (EQ 1) Powersave Operation In light load conditions, the integrated powersave feature removes power from all circuitry not required to monitor VOUT. When VOUT has dropped approximately 1% from nominal, the AS1337 powers up and begins normal PWM operation. ca COUT (see Figure 13 on page 7) recharges, causing the AS1337 to re-enter powersave mode as long as the output load remains below the powersave threshold. The frequency of this intermittent PWM is proportional to load current; i.e., as the load current drops further below the powersave threshold, the AS1337 turns on less frequently. When the load current increases above the powersave threshold, the AS1337 will resume continuous, seamless PWM operation. Buck Mode ni Note: An optional capacitor (CFF) between pins VOUT and FB in some applications can reduce VOUTp-p ripple and input quiescent current during powersave mode. Typical values for CFF range from 15pF to 220pF. ch Both devices, the AS1337A and the AS1337B, offer a low power buck mode for VIN > VOUT operation. The switching during buck mode is similar to boost mode, but with forced reduction of some energy internal to be able to provide a buck conversion. Te Shutdown When pin EN is low the AS1337 is switched off and <1A current is drawn from battery; when pin EN is high the device is switched on. If EN is driven from a logic-level output, the logic high-level (on) should be referenced to VOUT to avoid intermittently switching the device on. Note: If pin EN is not used, it should be connected directly to pin VOUT. Caution: Because of the feedthrough the output voltage is the same as the input voltage during shutdown. If VIN > VOUT the output voltage will jump to the value of the input voltage when the device switches into shutdown. During normal operation the device is in down conversion mode. www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 8 - 15 AS1337 Datasheet - D e t a i l e d D e s c r i p t i o n Shutdown Battery Feedthrough (AS1337A) In shutdown the battery input of the AS1337A is connected to the output through the inductor and the small internal synchronous rectifier P-FET. This allows the input battery to provide backup power for devices such as an idle microcontroller, memory, or real-time-clock, without the usual diode forward drop. In this way a separate backup battery is not needed. Shutdown Battery Disconnect (AS1337B) al id The AS1337B is designed to allow true output disconnect by opening both P-channel MOSFET rectifiers. During Shutdown VOUT is discharged via the internal NMOS transistor and connected to GND. POK Function lv The POK output indicates if the output voltage is within 88% (typ.) of the nominal voltage level. As long as the output voltage is within regulation the open-drain POK output is high impedance. The POK output can be tied to VIN or to VOUT or to any external voltage up to VIN or VOUT via a pull-up resistance (see Figure 1 on page 1). If the output voltage drops below 88% (typ.) of the nominal voltage the POK pin is pulled to GND. Te ch ni ca am lc s on A te G nt st il Note: It is important to consider that in shutdown mode the POK output is pulled to VIN in order to save current. www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 9 - 15 AS1337 Datasheet - A p p l i c a t i o n I n f o r m a t i o n 9 Application Information The AS1337 is perfectly suited for LED matrix displays, bar-graph displays, instrument-panel meters, dot matrix displays, set-top boxes, white goods, professional audio equipment, medical equipment, industrial controllers to name a few applications. Along with Figure 1 on page 1, Figure 14 and Figure 15 depict a few of the many applications for which the AS1337 converters are perfectly suited. L1 4.7H VOUT = 3.3V VOUT R1 560k FB R2 330k VIN = 1.5V VIN On Off AS1337 EN am lc s on A te G nt st il POK COUT 22F lv LX CIN 10F al id Figure 14. Single AA Cell to 3.3V Synchronous Boost Converter GND PGND Figure 15. Single Lithium Cell to 5V L1 4.7H VOUT = 5.0V LX Lithium-Ionen Cell CIN 10F VIN On Off EN R1 680k FB R2 220k AS1337 COUT 22F POK PGND Te ch ni ca GND VOUT www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 10 - 15 AS1337 Datasheet - A p p l i c a t i o n I n f o r m a t i o n Component Selection Only three power components are required to complete the design of the buck-boost converter, except the additional two resistors for the voltage divider to set VOUT. The high operating frequency and low peak currents of the AS1337 allow the use of low value, low profile inductors and tiny external ceramic capacitors. Inductor Selection al id The inductor should have low ESR to reduce the IR power losses, and must be able to handle the peak inductor current without saturating. High-frequency ferrite core inductor materials reduce frequency dependent power losses compared to less expensive powdered iron types, which result in improved converter efficiency. A 4.7H to 15H inductor value with a >850mA current rating and low DCR is recommended. For applications where radiated noise is a concern, a toroidal or shielded inductor can be used. lv Capacitor Selection A 10F capacitor is recommend for CIN as well as a 22F for COUT. Small-sized ceramic capacitors are recommended. X5R and X7R ceramic capacitors are recommend as they retain capacitance over wide ranges of voltages and temperatures. am lc s on A te G nt st il Output Capacitor Selection Low ESR capacitors should be used to minimize VOUT ripple. Multi-layer ceramic capacitors are recommended since they have extremely low ESR and are available in small footprints. A 1 to 10F output capacitor is sufficient for most applications. Larger values up to 22F may be used to obtain extremely low output voltage ripple and improve transient response. An additional phase lead capacitor may be required with output capacitors larger than 10F to maintain acceptable phase margin. X5R and X7R dielectric materials are recommended due to their ability to maintain capacitance over wide voltage and temperature ranges. Input Capacitor Selection Low ESR input capacitors reduce input switching noise and reduce the peak current drawn from the battery. Ceramic capacitors are recommended for input decoupling and should be located as close to the device as is practical. A 4.7F input capacitor is sufficient for most applications. Larger values may be used without limitations. Table 5. Recommended External Components Name Part Number Value Rating Type Size Manufacturer CIN GRM219R60J106KE19 10F 6.3V X5R 0805 COUT GRM21BR60J226ME39 22F 6.3V X5R 0805 Murata www.murata.com L1 MOS6020-472ML 4.7H 1.82A 50m 6.8x6.0x2.4mm ca Coilcraft www.coilcraft.com PCB Layout Guidelines ni The high-speed operation of the AS1337 requires proper layout for optimum performance. A large ground pin copper area will help to lower the device temperature. ch A multi-layer board with a separate ground plane is recommended. Traces carrying large currents should be direct. Te Trace area at pin FB should be as small as is practical. The lead-length to the battery should be as short as is practical. www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 11 - 15 AS1337 Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s 10 Package Drawings and Markings lv al id Figure 16. TDFN (3x3mm) 8-pin Marking YY am lc s on A te G nt st il Table 6. Packaging Code YYWWIZZ Q ZZ plant identifier free choice / traceability code Te ch ni ca last two digits of the current year WW manufacturing week www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 12 - 15 AS1337 Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s Te ch ni ca am lc s on A te G nt st il lv al id Figure 17. TDFN (3x3mm) 8-pin Package www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 13 - 15 AS1337 Datasheet - O r d e r i n g I n f o r m a t i o n 11 Ordering Information The device is available as the standard products listed in Table 7. Table 7. Ordering Information Marking Descriptiom Delivery Form Package AS1337A-BTDT ASSE 200mA, DC-DC Step-Up Converter with Buck Mode; Battery Connect in Shutdown Tape and Reel TDFN (3x3mm) 8-pin AS1337B-BTDT ASSF 200mA, DC-DC Step-Up Converter with Buck Mode; Battery Disconnect in Shutdown and Output Discharged Tape and Reel TDFN (3x3mm) 8-pin Te ch ni ca am lc s on A te G nt st il For further information and requests, please contact us mailto:sales@austriamicrosystems.com or find your local distributor at http://www.austriamicrosystems.com/distributor lv Note: All products are RoHS compliant and Pb-free. Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect al id Ordering Code www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 14 - 15 AS1337 Datasheet Copyrights Copyright (c) 1997-2010, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered (R). All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. al id Disclaimer lv Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. ca am lc s on A te G nt st il The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Headquarters ni Contact Information ch austriamicrosystems AG Tobelbaderstrasse 30 A-8141 Unterpremstaetten, Austria Te Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com/DC-DC_Step-Up/AS1337 Revision 1.05 15 - 15