96 MHz SAW Filter
20 MHz Bandwidth
Part Number: SF0096BA02458S
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0096BA02458S Rev A 22-Feb-2010
ECN 36650 Page 1 of 3
DESCRIPTION
• 96 MHz SAW bandpass filter with 20 MHz bandwidth.
• 5 x 7 mm SMP.
• RoHS compliant.
TYPICAL PERFORMANCE
Horizontal: Frequency : 10 MHz/div
Vertical from Top: Relative Magnitude : 10 dB/div
Relative magnitude : 1 dB/div
Phase Linearity : 5 deg/div
Group Delay Deviation : 100 ns/div
S11 S22
96 MHz SAW Filter
20 MHz Bandwidth
Part Number: SF0096BA02458S
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0096BA02458S Rev A 22-Feb-2010
ECN 36650 Page 2 of 3
SPECIFICATION
Parameter Min Typ Max Units
Center Frequency, FC 1 - 96.00 - MHz
Insertion Loss (86-106 MHz) 1,2 - 11.3 13 dB
1 dB Bandwidth 20.0 23.4 - MHz
Relative Attenuation to Ins Loss (0.3-68.4 MHz) 1,3 50 55 - dB
Relative Attenuation to Ins Loss (at 76.8 MHz) 1,3 45 50 - dB
Relative Attenuation to Ins Loss (123.6 to 162.8 MHz) 1,3 40 48 - dB
Relative Attenuation to Ins Loss (162.8 to 240 MHz) 1,3 35 53 - dB
Relative Attenuation to Ins Loss (240 to 1000 MHz) 1,3 25 35 - dB
Amplitude Ripple (86 to 106 MHz) 1,4 - 0.75 1 dB p-p
Group Delay Ripple (86 to 106 MHz) 1,5 50 60 ns/div
1 dB Compression Point (86 to 106 MHz) 12 15 - dBm
Input IP3 6 35 40 - dBm
Temperature Coefficient - 94 - ppm/˚C
Source/Load Impedance 50 ohms
Ambient Temperature - 25 - ˚C
Notes: 1. Measured with terminating impedance matched to 50Ω and with 50Ω analyzer.
2. Average Insertion Loss in indicated frequency range.
3. Measured as attenuation below the insertion loss point (Insertion loss is reference).
4. Amplitude ripple should be measured without smoothing.
5. Group delay ripple may be measured with a smoothing aperture of 250 KHz .
6. By design.
MAXIMUM RATINGS
Parameter Min Max Units
Storage Temperature Range -40 85 ˚C
Operating Temperature Range -25 85 ˚C
Input Power Level - 12 dBm
MATCHING CIRCUIT
Typical component values:
Notes:
1. Recommend use of 2% tolerance matching components.
2. Component values are for reference only and may change depending on board layout.
Ls1 = 220 nH Ls2 = 82 nH
Lp1 = 270 nH Rp2 = 680 Ω
10 4
All others
Input
50 Ω
Single-ended
Output
50 Ω
Single-ended
GND
96 MHz SAW Filter
20 MHz Bandwidth
Part Number: SF0096BA02458S
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0096BA02458S Rev A 22-Feb-2010
ECN 36650 Page 3 of 3
PACKAGE OUTLINE SUGGESTED FOOTPRINT
ISO 9001
Registered
All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice.
© 2010 All rights reserved.
Package Material:
Body: Al2O3 ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 1 µm min,
over a 1.3-8.9 µm Ni plating
Units: mm
Tolerances are ±0.15 mm except
for the overall length and width,
which are nominal values.
Pad Configuration:
Input: 10
Output: 4
Ground: All other pads
