Frequency coefficient of rated ripple current
Coefficient
Frequency 50 Hz
0.70
UBseries
Chip Type, High Reliability
Chip type, high temperature range, for +125°C use.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
Specifications Performance CharacteristicsItem
UB UX
Voltage
Capacitance
125°C Marking
Lot No.
Plastic platform
0.3MAX.
φD±0.5
B±0.2
A±0.2 A±0.2
C±0.2
0.5MAX.
E
H
H
Positive
Negative
Plastic platform
Pressure relief vent
0.3MAX.
φD±0.5
B±0.2
A±0.2 A±0.2
C±0.2
0.5MAX.
E
Positive
Negative
U
1U
2B
31
4A
51
60
71
8M
9C
10 L
11 1
12 G
13 S
14
Configuration
Taping code
Capacitance tolerance (±20%)
Rated capacitance
(
100µF
)
Rated voltage
(
10V
)
Series name
Type
φ
D × L
8 × 6.2
8 × 10
Code
CL
NL
10 × 10 NL
L±0.3
L±0.5
8 × 6.2
φD × L
A
B
C
E
3.3
8.3
8.3
2.3
8 × 10
2.9
8.3
8.3
3.1
10 × 10
3.2
10.3
10.3
4.5
L6.2 10 10
H
0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
(mm)
Voltage
Capacitance
Lot No.
Trade mark
Trade mark
125°C Marking
A2E
330
10V
A2E
100
10V
Chip Type
(φ8 × 6.2)
(φ8 × 10, φ10 × 10)
Type numbering system (Example : 10V 100
µ
F)
Rated ripple current (mArms) at 125°C 120Hz
Dimensions
010
022
033
047
100
220
330
100
220
330
470
101
221
331
8 × 6.2
8 × 10
10 × 10
8 × 10
10 × 10
8 × 6.2
8 × 10
10 × 10
8 × 6.2
8 × 10
10 × 10
8 × 6.2
8 × 6.2
8 × 10
10 × 10
58
90
112
66
102
48
74
116
44
52
80
24
38
46
58
1A 1C 1E 1V 1H
10 16 25 35 50
V
Code
Cap.(µF)
Rated
ripple
High
Temperature
ALUMINUM ELECTROLYTIC CAPACITORS
CJ
Added ESR specification
at
–
40
°C
WH
High
Temperature
Reflow
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in
page 18, 19.
Please select UH(p.116) series if high CV products are required.
Please refer to page 3 for the minimum order quantity.
Case size
φD × L (mm)
Category
Temperature Range
–40 to +125°C
Rated Voltage Range 10 to 400V
Rated Capacitance Range 1 to 330µF
±20% at 120Hz, 20°C
Capacitance Tolerance
Measurement frequency : 120Hz
The specifications listed at right shall be met when the
capacitors are restored to 20°Cafter the rated voltage is
applied for 2000 hours (1000 hours for φ8 × 6.2) at 125°C.
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
10
12
16
8
25
6
35
4
50
4
Rated voltage (V)
tan δ (MAX.)
10
0.32 16
0.24 25
0.21 35
0.18 50
0.18
Measurement frequency : 120Hz, Temperature : 20°C
Capacitance change
Leakage current
tan δ
Within ±30% of the initial capacitance value
Less than or equal to the initial specified value
300% or less than the intial specified value
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
The capacitors are kept on a hot plate for 30 seconds,
which is maintained at 250°C. The capacitors shall meet
the characteristic requirements listed at right when they
are removed from the plate and restored to 20°C.
Black print on the case top.
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
Capacitance change
Leakage current
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
Rated voltage (V) 10 to 50 160 to 400
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA).
I = 0.04CV+100(µA) max.(1 minute's)
Leakage Current
160
0.30 200
0.30 250
0.30 400
0.30
160
8
200
8
250
8
400
12
1
1.8
2.2
3.3
4.7
6.8
10
010
1R8
2R2
3R3
4R7
6R8
100 8× 10
10× 10 42
59
2C
Cap.(µF)
V160
Code
8× 10
10× 10
10× 10
2D
200
8× 10
8× 10
10× 10
10× 10
26
27
36
38
2G
400
8× 10
10× 10
36
59
59
28
59
2E
250
1.00 1.17 1.36 1.50
120 Hz 300 Hz 1 kHz
10 kHz or more
(Through 50V only)
CAT.8100A
