Ceramic Chip Capacitors Multilayer chip capacitors have a low residual inductance, an excellent frequency response and minimal stray capacitance since there are no leads. These characteristics enable design to be very close to the theoretical values of the capacitors. NP0/C0G: SPECIFICATIONS: Typical Capacitance Change vs. Temperature 15% 10% 5% AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS: 0% -5% -10% -15% OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: TEMPERATURE VOLTAGE COEFFICIENT: DISSIPATION FACTOR: INSULATION RESISTANCE: -55C -25C 0C X7R: 25C 50C 75C 100C 125C SPECIFICATIONS: Typical Capacitance Change vs. Temperature 15% 10% CAPACITANCE TOLERANCE: OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: TEMPERATURE VOLTAGE COEFFICIENT: DISSIPATION FACTOR: 5% 0% INSULATION RESISTANCE: -5% -10% -15% -55C -25C 0C X5R: 25C 50C 75C 100C 125C SPECIFICATIONS: Typical Capacitance Change vs. Temperature 15% 10% AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS:* CAPACITANCE TOLERANCE: OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: TEMPERATURE VOLTAGE COEFFICIENT: DISSIPATION FACTOR: AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS:* CAPACITANCE TOLERANCE: OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: DISSIPATION FACTOR: INSULATION RESISTANCE: AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS: CAPACITANCE TOLERANCE: +10C to +85C +22% - 56%C MAX. 4.0% MAX. >100 ohms F or 10 G ohms, whichever is less at 25C, VDCW. 5% per decade hour, typical >2.5 times VDCW 1KHz 100Hz at 0.5 0.1 Vrms, 25C M,Z,P OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: DISSIPATION FACTOR: -30C to +85C +22% - 82%C MAX. For 25 volts and 50 volts: 5% MAX.; For 16 volts: 7% MAX.; For 10 volts: 9% MAX.; For 6.3 volts: 11% MAX. For higher Cap values > 10F, the D.F. is 20% MAX. >100 ohms F or 10 G ohms, whichever is less at 25C, VDCW. 7% per decade hour, typical >2.5 times VDCW 1KHz 100Hz at 1.0 0.2 Vrms, 25C M,Z 0% INSULATION RESISTANCE: -10% -15% -55nC -25nC 0nC Z5U: 25nC 50nC 75nC 100nC 125nC SPECIFICATIONS: Typical Capacitance Change vs. Temperature 20% 0% -20% -40% -60% -80% -55C -25C 0C Y5V: 25C 50C 75C 100C 125C SPECIFICATIONS: Typical Capacitance Change vs. Temperature 40% 20% 0% -20% -40% -60% -80% -100% -55C -25C 0C 25C 50C 75C 100C 125C INSULATION RESISTANCE: AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS:* CAPACITANCE TOLERANCE: * -55C to +125C 0 15%C MAX. X7R not applicable For 50 volts and 100 volts: 2.5% MAX.; For 25 volts: 3.0% MAX.; For 16 volts: 3.5% MAX.; For 10 volts: 5.0% MAX.; For 6.3 volts: 10% MAX. For values > 10F and voltages 10V, the D.F. is 10% MAX. >1000 ohms F or 100 G ohms, whichever is less at 25C, VDCW. (The IR at 125C is 10% of the value at 25C) 2.5% per decade hour, typical >2.5 times VDCW 1KHz 100Hz at 1.0 0.2 Vrms > 100 pF, 25C J,K,M -55C to +85C 0 15%C MAX. X5R not applicable For 50 volts and 100 volts: 2.5% MAX.; For 25 volts: 3.0% MAX.; For 16 volts: 3.5% MAX.; For 10 volts: 5.0% MAX.; For 4.0 volts and 6.3 volts: 10% MAX. For values > 10F and voltages 10V, the D.F. is 10% MAX. >1000 ohms F or 100 G ohms, whichever is less at 25C, VDCW. (10,000 ohms at 125C) 2.5% per decade hour, typical >2.5 times VDCW 1KHZ 100Hz at 1.0 0.2 Vrms > 100 pF, 25C K,M 5% -5% -55C to +125C 0 30PPM/C 0 30PPM/C 0.1% MAX. >1000 ohms F or 100 G ohms, whichever is less at 25C, VDCW. (The IR at 125C is 10% of the value at 25C) None >2.5 times VDCW 1MHz 100KHz at 1.0 0.2 Vrms 100 pF, 25C 1KHz 100Hz at 1.0 0.2 Vrms > 100 pF, 25C B,C,D,F,G,J,K Test parameters for Hi-Caps: X7R, X5R and Y5V 1KHz 100Hz at 1.0 0.2 Vrms 10uF (10 V min.) 1KHz 100Hz at 0.5 0.1 Vrms 10uF (6.3V max.) 120Hz 24Hz at 0.5 0.1 Vrms > 10uF All components in this section are RoHS compliant per the EU directives and definitions. Reel Dimensions G All tape and reel specifications must be adhered to per EIA-481-1-A as noted and stated in the Chip Resistor section on page 61. B D A T T 10 PITCHES CUMULATIVE TOLERANCE 0.008 ( 0.2 ) D Po Pz E A F W B t PAPER EMBOSSED TOP TAPE P C A (7") A (13") D min N min G T max 8mm 0.3 (.012) 0.3 (.012) 13 .05 (.512 .02) 13 .05 (.512 .02) 178 2.0 (7 .079) 178 2.0 (7 .079) 330 2.0 (13 .08) 330 2.0 (13 .08) 20.2 (.795) 20.2 (.795) 50 (1.97) 50 (1.97) 10 1.5 (.394 .059) 10 1.5 (.394 .059) 14.9 (.587) 14.9 (.587) 7 in. Reel Quantities** Taping Specifications To B min 12mm N C FULL RADIUS Unit: mm (inch) TAPE SIZE 01005 0201* 0402* 0603 0805 1206 1210 1812 2221 TAPE SIZE 8mm 8mm 8mm 8mm 8mm 8mm 8mm 12mm 12mm MIN QTY PER REEL 20,000 15,000 5000 3000 2000 2000 1000 1000 1000 MAX QTY PER REEL 20,000 15,000 10,000 4000 5000 5000 5000 3000 1000 ** Quantity dependent on Chip Thickness * 0201 and 0402 Pitch ("P") is .079" .004" (2.0 0.1mm) Smaller quantities may be available. Please contact your sales person. CENTER OF CAVITY DIRECTION OF FEED Paper Tape Carrier Dimensions Unit: mm (inch) SIZE A B W F E Po Pz D t P 0.25 0.05 0.45 0.05 8.0 0.2 3.5 0.1 1.75 0.1 4.0 0.1 2.0 0.05 1.15 max 2.0 0.05 (0.010 .002) (0.018 .002) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.039 .002) 1.5 + 0.1 - 0.0 .064 + .004 - .000 (.045 max) (.079 .002) 0.37 0.05 0.67 0.05 8.0 0.2 3.5 0.1 1.75 0.1 4.0 0.1 2.0 0.05 1.15 max 2.0 0.05 (0.014 .002) (0.026 .002) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.039 .002) (.045 max) (.079 .002) 0.65 0.1 1.10 0.2 8.0 0.2 3.5 0.1 1.75 0.1 4.0 0.1 2.0 0.05 1.15 max 2.0 0.05 (.026 .004) (.043 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.039 .002) (.045 max) (.079 .002) 1.10 0.2 1.90 0.2 8.0 0.2 3.5 0.1 1.75 0.1 4.0 0.1 2.0 0.05 1.15 max 4.0 0.1 (.043 .008) (.075 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.079 .002) (.045 max) (.157 .004) 1.16 0.2 2.4 0.2 8.0 0.2 3.5 0.1 1.75 0.1 4.0 0.1 2.0 0.05 1.15 max 4.0 0.1 (.046 .008) (.095 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.079 .002) (.045 max) (.157 .004) 2.0 0.2 3.6 0.2 8.0 0.2 3.5 0.1 1.75 0.1 4.0 0.1 2.0 0.05 1.15 max 4.0 0.1 (.079 .008) (.142 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.079 .002) (.045 max) (.157 .004) 01005 ( 0201 (8mm) ( 0402 ( ( 0805 ( 1206 (8mm & 12mm) SIZE 0805 1206 1210 1812 C0805 C0G Series Temperature See Chart Characteristic 500 1.5 + 0.1 - 0.0 .064 + .004 - .000 1.5 + 0.1 - 0.0 .064 + .004 - .000 0603 Embossed Carrier Dimensions 1.5 + 0.1 - 0.0 .064 + .004 - .000 ( 1.5 + 0.1 - 0.0 .064 + .004 - .000 1.5 + 0.1 - 0.0 .064 + .004 - .000 ) ) ) ) ) ) A B W F E Po Pz D To T P 1.48 0.2 2.3 0.2 8.0 0.2 3.5 .0.1 1.75 0.1 4.0 0.1 2.0 0.05 1.5 + 0.1 - 0.0 + .004) (.06 - .000 1.5 + 0.1 - 0.0 + .004) (.06 - .000 1.5 + 0.1 - 0.0 + .004) (.06 - .000 1.5 + 0.1 - 0.0 + .004) (.06 - .000 2.5 max 0.6 max 4.0 0.1 (.058 .008) (.091 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.079 .002) 2.0 0.2 3.6 0.2 8.0 0.2 3.5 .0.1 1.75 0.1 4.0 0.1 2.0 0.05 (.079 .008) (.142 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.079 .002) 2.9 0.2 3.6 0.2 8.0 0.2 3.5 .0.1 1.75 0.1 4.0 0.1 2.0 0.05 (.114 .008) (.142 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.079 .002) 3.6 0.2 4.9 0.2 12.0 0.3 5.6 .0.1 1.75 0.1 4.0 0.1 2.0 0.05 (.142 .008) (.193 .008) (.472 .012) (.221 .004) (.069 .004) (.157 .004) (.079 .002) -- 101 J How To Order N h (.098 max) (.024 max) (.157 .004) 2.5 max 0.6 max 4.0 0.1 (.098 max) (.024 max) (.157 .004) 2.5 max 0.6 max 4.0 0.1 (.098 max) (.024 max) (.157 .004) 3.8 max 0.6 max 8.0 0.1 (.150 max) (.024 max) (.315 .004) P -- * Rated Voltage Capacitance Tolerance Code: Termination Marking** Packaging Optional Identifier 1st two digits (pico - Farads) *B = 0.1 pF N = Nickel Barrier, 6 = EIA "J" Code D = Paper Tape (10" Reel ) are significant 1st two digits *C = 0.25 pF Tinned Termination "Leave blank if E = Embossed Tape ( 7" Reel ) followed by are significant, *D = 0.5 pF Composition is No Marking" P = Paper Tape (7" Reel ) number of zeroes. followed by F = 1% 100% matte Tin (Sn) R = Paper Tape (13" Reel ) 4R0 = 4.0 VDCW number of zeroes. G = 2% P = Palladium Silver U = Embossed Tape ( 13" Reel ) 6R3 = 6.3 VDCW 101 = 100 pF J = 5% G = Gold over Nickel 100 = 10 VDCW R denotes decimal K = 10% Pb: 90% Tin (Sn)/10% Lead (Pb) Termination 160 = 16 VDCW 6R8 = 6.8 pF M = 20% ** 0201 and 0402 250 = 25 VDCW N = 30% Standard termination finish for this product is size capacitors 500 = 50 VDCW Z = +80 - 20% 100% matte Tin (Sn). If a 100% Tin designation is cannot be marked 630 = 63 VDCW P = +100 - 0% required, replace the N with Sn. 101 = 100 VDCW * For capacitance values below 201 = 200 VDCW Pd/Ag & Gold terminations have limited values 251 = 250 VDCW 10 pF only. available. Please consult your salesperson. See pages 20-21 for our standard High Voltage Ceramic Chip Capacitors. - * OPTIONAL IDENTIFIER Min./Max. thickness The following letters define thickness as signified below: CODE: B C D E F G H I J K L M N O P Q R S 6 DIMENSION: .010 .015 .020 .026 .030 .035 .040 .045 .050 .055 .060 .065 .070 .075 .080 .085 .090 .095 .023 - designates minimum thickness * designates maximum thickness Please Note: Venkel offers Engineering Kits for this product. See page 117 for details. NOTE: See the Web site for soldering information. 0603 size and smaller are not recommended for wave soldering. Ceramic Chip Capacitors NP0/C0G Dielectric Values that are typically available. L END BAND W 25V Available in 25V only. T (All measurements in inches) Size 01005 ( 0.0008) 0504 ( 0.008) 0603 ( 0.006) 0805 ( 0.008) 1206 ( 0.008) 1210 (0.008) 1812 (0.012) .024 .040 .053 .063 .080 .126 .126 .177 W .008 .012 .020 .040 .032 .050 .063 .098 .126 T (max)* .008 .012 .025 .040 .033 .055 .070 .075 .085 Min E/B .002 .002 .004 .005 .008 .020 .010 .020 .010 .020 .010 .024 .015 1R8 2R2 2R7 3R3 3R9 4R7 5R6 6R8 8R2 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10pF 12 15 2.0 1R5 100V 50V 100V 0.5pF 1.0pF 3.0 1R2 50V 0.4pF 9.0 8.0 7.0 6.0 5.0 4.0 1R0 50V * Va l u e s s h o w n t o t h e l e f t a re a l s o a v a i l a b l e f o r 0 2 0 1 s i z e 0R5 25V 0.3pF 2.0 0R4 50V 0.2pF 3.0 0R3 25V 9.0 8.0 7.0 6.0 5.0 4.0 0R2 16V 0.1pF * Va l u e s s h o w n t o t h e l e f t a re a v a i l a b l e f o r 0 1 0 0 5 s i z e 0R1 <--------------------------------------------------------------------------------------------------------CAP. VALUE-------------------------------------------------------------------------------------------------------> <--------------------------------------------------------------------------------------------------------CAP. CODE--------------------------------------------------------------------------------------------------------> 0402 ( 0.004) .016 VDCW (MAX) 0201 ( 0.002) L 18 22 27 33 39 47 56 68 82 100pF 120 150 180 220 270 330 390 470 560 680 820 1000pF 1200 1500 1800 2200 2700 3300 Note: * For additional values that may be available, please consult your salesperson. 25V 50V 100V 50V 100V 50V 100V 50V 100V Ceramic Chip Capacitors NP0/C0G Dielectric Values that are typically available. L END BAND W 25V Available in 25V only. T (All measurements in inches) Size 0201 ( 0.002) 0504 ( 0.008) 0603 ( 0.006) 0805 ( 0.008) 1206 ( 0.008) 1210 (0.008) 1812 (0.012) 2220 / 2221 (0.016) .024 .040 .053 .063 .080 .126 .126 .177 .225 / .225 W .012 .020 .040 .032 .050 .063 .098 .126 .200 / .210 T (max)* .012 .025 .040 .033 .055 .070 .075 .085 .108 /.108 Min E/B .002 .004 .005 .008 .020 .010 .020 .010 .020 .010 .024 .015 .025 .015 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 335 395 475 685 106 156 226 476 107 <--------------------------------------------------------------------------------------------CAP. VALUE-------------------------------------------------------------------------------------------> VDCW (MAX) <--------------------------------------------------------------------------------------------CAP. CODE--------------------------------------------------------------------------------------------> 0402 ( 0.004) L 25V 25V 50V 50V 100V 25V 50V 25V 50V 100V 50V 100V 50V 100V 50V 100V 50V 100V 3900 4700 5600 6800 8200 .01F .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100F 25V .120 .150 .180 .220 .270 .330 .390 .470 .560 .680 .820 1.00F 1.20 1.50 1.80 2.20 3.30 3.90 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. * For values above 1uF, thickness may be greater than specified above. Ceramic Chip Capacitors X7R Dielectric Values that are typically available. L END BAND W X5R T Available in X5R only. See X5R chart on page 14, for all values 1F and above (All measurements in inches) Size 01005 ( 0.0008) 0402 ( 0.004) 0504 ( 0.008) 0603 ( 0.006) 0805 ( 0.008) .016 .024 .040 .053 .063 .080 W .008 .012 .020 .040 .032 .050 T (max)* .008 .012 .025 .040 .033 .055 Min E/B .002 .002 .004 .005 .008 .020 .010 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 <----------------------------------------------------------------------------------------------CAP. VALUE---------------------------------------------------------------------------------------------> VDCW (MAX) <----------------------------------------------------------------------------------------------CAP. CODE----------------------------------------------------------------------------------------------> 0201 ( 0.002) L 6.3V 6.3V 10V 16V 25V 16V 25V 50V 25V 50V 100V 10V 16V 25V 50V 100V 25V 50V 100pF 120 150 180 220 270 330 390 470 560 680 820 1000pF X5R 1200 1500 X5R 1800 2200 X5R 2700 3300 X5R 3900 4700 X5R 5600 6800 X5R 8200 .01F X5R .012 .015 X5R .018 .022 X5R .027 .033 X5R * For values above 1uF, thickness may be greater than specified above. T(max): 0603 - 0.048" 0805 - 0.075" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. 10 All components manufactured with the X7R dielectric are also available as an X5R dielectric. 100V Ceramic Chip Capacitors X7R Dielectric Values that are typically available. L END BAND W X5R T Available in X5R only. See X5R chart on page 14, for all values 1F and above (All measurements in inches) Size 0201 ( 0.002) 0603 ( 0.006) 0805 ( 0.008) .024 .040 .063 .080 W .012 .020 .032 .050 T (max)* .012 .025 .033 .055 Min E/B .002 .004 .008 .020 .010 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 335 475 685 106 156 226 476 107 <----------------------------------------------------------------------------------------------CAP. VALUE------------------------------------------------------------------------------------------> VDCW (MAX) <----------------------------------------------------------------------------------------------CAP. CODE------------------------------------------------------------------------------------------> 0402 ( 0.004) L 4V 6.3V .039 X5R .047 X5R 10V 4V 6.3V 10V 16V 25V 6.3V 10V 16V 25V 50V 100V 6.3V 10V 16V 25V 50V 100V .056 .068 .082 .100F X5R .120 .150 .180 .220 X5R X5R X5R .270 .330 X5R .390 .470 .560 .680 X5R X5R .820 1.00F X5R X5R X5R 1.20 1.50 1.80 2.20 X5R X5R X5R X5R X5R X5R X5R 3.30 X5R 4.70 X5R X5R 6.80 10.0F X5R X5R 15.0F 22.0F 47.0F 100.0F * For values above 1uF, thickness may be greater than specified above. T(max): 0603 - 0.048" 0805 - 0.075" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. All components manufactured with the X7R dielectric are also available as an X5R dielectric. 11 Ceramic Chip Capacitors X7R Dielectric L W Values that are typically available. END BAND X5R T Available in X5R only. See X5R chart on page 14, for all values 1F and above (All measurements in inches) Size 1206 ( 0.008) 1812 (0.012) 2220 / 2221 (0.016) .126 .126 .177 .225 / .225 W .063 .098 .126 .200 / .210 T (max)* .070 .075 .085 .108 /.108 Min E/B .020 .010 .020 .010 .024 .015 .025 .015 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 <----------------------------------------------------------------------------------------------CAP. VALUE---------------------------------------------------------------------------------------------> VDCW (MAX) <----------------------------------------------------------------------------------------------CAP. CODE----------------------------------------------------------------------------------------------> 1210 (0.008) L 10V 16V 25V 50V 100V 10V 16V 25V 50V 100V 6.3V 10V 16V 25V 50V 100V 16V 25V 50V 1000pF 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .01F .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100F .120 .150 .180 .220 .270 .330 * For values above 1uF, thickness may be greater than specified above. T(max): 1206 - 0.110" 1812 - 0.130" 1210 - 0.125" 2220 - 0.135" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. All components manufactured with the X7R dielectric are also available as an X5R dielectric. 12 100V Ceramic Chip Capacitors X7R Dielectric L W Values that are typically available. END BAND X5R T Available in X5R only. See X5R chart on page 14, for all values 1F and above (All measurements in inches) Size 1206 ( 0.008) 1812 (0.012) 2220 / 2221 (0.016) .126 .126 .177 .225 / .225 W .063 .098 .126 .200 / .210 T (max)* .070 .075 .085 .108 /.108 Min E/B .020 .010 .020 .010 .024 .015 .025 .015 394 474 564 684 824 105 125 155 185 225 335 475 685 106 156 226 476 107 <-----------------------------------------------------CAP. VALUE--------------------------------------------------> VDCW (MAX) <-----------------------------------------------------CAP. CODE--------------------------------------------------> 1210 (0.008) L 10V 16V 25V 50V 100V 10V 16V 25V 50V 100V 6.3V 10V 16V 25V 50V 100V 16V 25V 50V 100V .390 .470 .560 .680 .820 1.00F 1.20 1.50 1.80 2.20 3.30 4.70 6.80 10.0F X5R X5R X5R 15.0F 22.0F X5R X5R X5R X5R X5R 47.0F X5R X5R X5R X5R 100.0F * For values above 1uF, thickness may be greater than specified above. T(max): 1206 - 0.110" 1812 - 0.130" 1210 - 0.125" 2220 - 0.135" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. All components manufactured with the X7R dielectric are also available as an X5R dielectric. 13 Ceramic Chip Capacitors X5R Dielectric (1F and above) Values that are typically available. L For values less than 1F, see X7R chart on pages 10-13. END BAND W T (All measurements in inches) 0402 ( 0.004) Size 0805 ( 0.008) 1206 ( 0.008) 1812 (0.012) 1210 (0.008) L .040 .063 .080 .126 .126 .177 W .020 .032 .050 .063 .098 .126 T (max)* .025 .033 .055 .070 .075 .085 Min E/B .004 .008 .020 .010 .020 .010 .020 .010 .024 .015 105 125 155 185 225 335 <------------CAP. VALUE-----------> VDCW (MAX) <------------CAP. CODE-----------> 0603 ( 0.006) 4V 6.3V 10V 4V 6.3V 10V 16V 25V 6.3V 10V 16V 25V 6.3V 10V 16V 25V 6.3V 10V 16V 25V 6.3V 1.00F 1.20 1.50 1.80 2.20 3.30 * For values above 1uF, thickness may be greater than specified above. T(max): 0603 - 0.048" 1206 - 0.110" 1812 - 0.130" 0805 - 0.075" 1210 - 0.125" 2220 - 0.135" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. All components manufactured with the X7R dielectric are also available as an X5R dielectric. 14 10V 16V Ceramic Chip Capacitors X5R Dielectric (1F and above) Values that are typically available. L For values less than 1F, see X7R chart on pages 10-13. END BAND W T (All measurements in inches) 0402 ( 0.004) Size 0805 ( 0.008) 1206 ( 0.008) 1812 (0.012) 1210 (0.008) 2220 / 2221 (0.016) L .040 .063 .080 .126 .126 .177 .225 / .225 W .020 .032 .050 .063 .098 .126 .200 / .210 T (max)* .025 .033 .055 .070 .075 .085 .108 /.108 Min E/B .004 .008 .020 .010 .020 .010 .020 .010 .024 .015 .025 .015 395 475 685 106 156 226 476 107 <-----------------CAP. VALUE-----------------> VDCW (MAX) <-----------------CAP. CODE-----------------> 0603 ( 0.006) 6.3V 4V 6.3V 10V 4V 6.3V 10V 16V 25V 6.3V 10V 16V 25V 6.3V 10V 16V 25V 6.3V 10V 16V 25V 6.3V 10V 25V 50V 3.90 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F * For values above 1uF, thickness may be greater than specified above. T(max): 0603 - 0.048" 1206 - 0.110" 1812 - 0.130" 0805 - 0.075" 1210 - 0.125" 2220 - 0.135" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. All components manufactured with the X7R dielectric are also available as an X5R dielectric. 15 Ceramic Chip Capacitors Z5U Dielectric Values that are typically available. L END BAND W T (All measurements in inches) Size 0504 ( 0.008) 0805 ( 0.008) 1206 ( 0.008) 1210 (0.008) 1812 (0.012) 2220 / 2221 (0.016) .050 .063 .080 .126 .126 .177 .225 / .225 W .040 .032 .050 .063 .098 .126 .200 / .210 T (max)* .040 .033 .055 .070 .075 .085 .108 /.108 Min E/B .005 .008 .020 .010 .020 .010 .020 .010 .024 .015 .025 .015 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 <----------------------------------------------------------------------------------------------CAP. VALUE---------------------------------------------------------------------------------------------> VDCW (MAX) <----------------------------------------------------------------------------------------------CAP. CODE----------------------------------------------------------------------------------------------> 0603 ( 0.006) L 25V 50V 25V 50V 25V 50V 25V 50V 25V 50V 25V 50V 25V 1000pF 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .01F .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100F .120 .150 .180 .220 .270 .330 Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. * For values above 1uF, thickness may be greater than specified above. 16 50V Ceramic Chip Capacitors Z5U Dielectric Values that are typically available. L END BAND W T (All measurements in inches) Size 0504 ( 0.008) 0805 ( 0.008) 1206 ( 0.008) 1210 (0.008) 1812 (0.012) 2220 / 2221 (0.016) .050 .063 .080 .126 .126 .177 .225 / .225 W .040 .032 .050 .063 .098 .126 .200 / .210 T (max)* .040 .033 .055 .070 .075 .085 .108 /.108 Min E/B .005 .008 .020 .010 .020 .010 .020 .010 .024 .015 .025 .015 394 474 564 684 824 105 125 155 185 225 335 395 475 685 106 156 226 476 107 <-------------------------------------------------------CAP. VALUE-----------------------------------------------------> VDCW (MAX) <-------------------------------------------------------CAP. CODE-----------------------------------------------------> 0603 ( 0.006) L 25V 50V 25V 50V 25V 50V 25V 50V 25V 50V 25V 50V 25V 50V .390 .470 .560 .680 .820 1.00F 1.20 1.50 1.80 2.20 3.30 3.90 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. * For values above 1uF, thickness may be greater than specified above. 17 Ceramic Chip Capacitors Y5V Dielectric Values that are typically available. L END BAND W T (All measurements in inches) 0201 ( 0.002) 0402 ( 0.004) 0603 ( 0.006) 0805 ( 0.008) 1206 ( 0.008) 1210 (0.008) 1812 (0.012) L .024 .040 .063 .080 .126 .126 .177 W .012 .020 .032 .050 .063 .098 .126 T (max)* .012 .025 .033 .055 .070 .075 .085 Min E/B .002 .004 .008 .020 .010 .020 .010 .020 .010 .024 .015 VDCW (MAX) 10V 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 <----------------------------------------------------------------------------------------------CAP. VALUE---------------------------------------------------------------------------------------------> <----------------------------------------------------------------------------------------------CAP. CODE---------------------------------------------------------------------------------------------> Size 6.3V 10V 16V 25V 50V 6.3V 10V 16V 25V 50V 6.3V 10V 16V 25V 50V 10V 16V 25V 50V 6.3V 10V 16V 25V 6.3V 1000pF 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .01F .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100F .120 .150 .180 .220 .270 .330 Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. * For values above 1uF, thickness may be greater than specified above. 18 10V 25V Ceramic Chip Capacitors Y5V Dielectric Values that are typically available. L END BAND W T (All measurements in inches) 0201 ( 0.002) 0402 ( 0.004) 0603 ( 0.006) 0805 ( 0.008) 1206 ( 0.008) 1210 (0.008) 1812 (0.012) L .024 .040 .063 .080 .126 .126 .177 W .012 .020 .032 .050 .063 .098 .126 T (max)* .012 .025 .033 .055 .070 .075 .085 Min E/B .002 .004 .008 .020 .010 .020 .010 .020 .010 .024 .015 VDCW (MAX) 10V 394 474 564 684 824 105 125 155 185 225 335 395 475 685 106 156 226 476 107 <------------------------------------------------------CAP. VALUE------------------------------------------------------> <------------------------------------------------------CAP. CODE------------------------------------------------------> Size 6.3V 10V 16V 25V 50V 6.3V 10V 16V 25V 50V 6.3V 10V 16V 25V 50V 10V 16V 25V 50V 6.3V 10V 16V 25V 6.3V 10V 25V .390 .470 .560 .680 .820 1.00F 1.20 1.50 1.80 2.20 3.30 3.90 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply. * For values above 1uF, thickness may be greater than specified above. All components in this section are RoHS compliant per the EU directives and definitions. 19