FES DC-DC Series Data Sheet Single-Output, 300 Watts Features * * * * * * * * 60A "full-brick" Very high efficiency Open-frame packaging 100C baseplate operation Planar magnetics Excellent transient response 1500V isolation Synchronous rectification Description FES single output dc-dc converters provide up to 300 watts of output power and up to 60 amperes of output current in a full-brick package. The FES converters feature open-frame packaging, along with planar magnetics and a high efficiency topology, to provide maximum useable power density. The FES converters use 100% surface-mount construction and are fully compatible with production board washing processes. Technical Specifications Input Voltage Range 48 VDC Nominal Undervoltage Lockout - Turn on / Turn off 36 - 75 VDC 34 / 32 VDC Output 1% 0.2% Vout 0.2% Vout 0.5 VDC 10 % Iout Rated 25% Iout 4% Vout 500 s 10% 110 - 140% 120 - 140% Vout Nom. Self Recovering Shutdown/Hiccup Switching Frequency Isolation Input - Output Input - Case Output - Case Temperature Coefficient Case Temperature Operating Range Storage Range Thermal Shutdown Range Vibration, 3 Axes, 5 Min Each MTBF (Bellcore TR-NWT-000332) Safety Weight (Approx.) 95 90 85 80 FES200ZE-A 75 EFF. (36V) EFF. (48V) 70 General Turn-On Time Remote Shutdown Remote Shutdown Reference Efficiency vs. Load (48V Input) EFFICIENCY % Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Remote Sense Headroom Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Voltage Trim Range Current Limit Threshold Range, % of Iout Rated OVP Trip Range OVP Type Short Circuit/Over Current Protection EFF. (75V) 10 ms Positive Logic Vin Negative 200 or 300 kHz 1500 VDC 1050 VDC 500 VDC 0.03%/C -40 To +100C -40 To +125C 105 To 125C 5 g, 10 - 55 Hz Consult Factory UL, cUL, TUV 4.4 oz REV. JUN 03, 2004 Page 1 of 3 65 60 10 20 30 40 50 60 70 80 90 100 LOAD % Notes MTBF predictions may vary slightly from model to model. Specifications typically at 25C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. FES DC-DC Series Data Sheet Single-Output, 300 Watts Model Selection MODEL INPUT VOLTAGE (VOLTS) INPUT VOLTAGE RANGE (VOLTS) MAXIMUM INPUT CURRENT (AMPS)* OUTPUT VOLTAGE (VOLTS) RATED OUTPUT CURRENT (AMPS) 48 48 48 48 36 - 75 36 - 75 36 - 75 36 - 75 4.5 6.5 7.0 10.5 3.3 5.0 3.3 5.0 40 40 60 60 FES132ZE-A FES200ZG-A FES200ZE-A FES300ZG-A RIPPLE & NOISE pk-pk (mV) TYPICAL EFFICIENCY** 100 100 100 100 87% 80% 81% 84% * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. Model numbers highlighted in yellow or shaded are not recommended for new designs. Mechanical Drawing "" " ! #$ ! #$ ! Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 5.4 C/W 3.8 C/W 2.5 C/W 1.7 C/W 1.6 C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. Pin Function 1 -Vin 2 3 4 Case Enable +Vin Inches: .XX 0.020 .XXX .010 5 -Vout 6 -Vout Pin: 0.002 7 8 9 10 -Sense Trim +Sense +Vout 11 +Vout REV. JUN 03, 2004 Page 2 of 3 Tolerances (Millimeters) .X 0.5 .XX 0.25 0.05 (Dimensions as listed unless otherwise specified.) OPTIONS This page is offered as a reference. Consult factory for actual availability of options. When ordering equipment options, use the following suffix information. Select preferred option(s) and add the suffix to the model number. Ordering option examples are located below the options table. OPTION SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, HLS, HLD, LES, QBS, QES, QLS, TES, TQD Lucent-Compatible Trim T HAS, HBD, HBS, HES, HLS, QBS, QES, QLS Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Pin Length and Heat Sink Options REMARKS TTL "Low" Turns Module ON TTL "High" Turns Module OFF Standard Pin Length is 0.180" (4.6mm) 0.110" (2.8mm) Pin Length 8 All Leaded Models 0.150" (3.8mm) Pin Length 9 All Leaded Models 0.24" (6.1mm) Horizontal Heat Sink 1H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.24" (6.1mm) Vertical Heat Sink 1V All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.45" (11.4mm) Horizontal Heat Sink 2H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.45" (11.4mm) Vertical Heat Sink 2V All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.95" (24.1mm) Horizontal Heat Sink 3H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.95" (24.1mm) Vertical Heat Sink 3V All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad Example Options: HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95" vertical heat sink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent-compatible trim and 0.110" pin length. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. REV. JUN 03, 2004 Page 3 of 3