REV. JUN 03, 2004
FES DC-DC Series Data Sheet
Single-Output, 300 Watts
Page 1 of 3
FES200ZE-A
60
65
70
75
80
85
90
95
10 20 30 40 50 60 70 80 90 100
LOAD %
EFFICIENCY %
EFF. (36 V)
EFF. (48 V)
EFF. (75 V)
Setpoint Accuracy ±1%
Line Regulation VinMin. - VinMax., IoutRated 0.2% Vout
Load Regulation IoutMin. - IoutMax., VinNom. 0.2% Vout
Remote Sense Headroom 0.5 VDC
Minimum Output Current 10 % IoutRated
Dynamic Regulation, Loadstep 25% Iout
Pk Deviation 4% Vout
Settling Time 500 µs
Voltage Trim Range ±10%
Current Limit Threshold Range, % of IoutRated 110 - 140%
OVP Trip Range 120 - 140% VoutNom.
OVP Type Self Recovering
Short Circuit/Over Current Protection Shutdown/Hiccup
Technical Specifications
FES single output dc-dc converters provide up to 300 watts of output power and up to 60 amperes of output current in
a full-brick package. The FES converters feature open-frame packaging, along with planar magnetics and a high
efficiency topology, to provide maximum useable power density. The FES converters use 100% surface-mount
construction and are fully compatible with production board washing processes.
• 60A “full-brick”
• Very high efficiency
• Open-frame packaging
• 100°C baseplate operation
• Planar magnetics
• Excellent transient response
• 1500V isolation
• Synchronous rectification
Description
Features
General
Turn-On Time 10 ms
Remote Shutdown Positive Logic
Remote Shutdown Reference VinNegative
Switching Frequency 200 or 300 kHz
Isolation
Input - Output 1500 VDC
Input - Case 1050 VDC
Output - Case 500 VDC
Temperature Coefficient 0.03%/°C
Case Temperature
Operating Range -40 To +100°C
Storage Range -40 To +125°C
Thermal Shutdown Range 105 To 125°C
Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz
MTBF†(Bellcore TR-NWT-000332) Consult Factory
Safety UL, cUL, TUV
Weight (Approx.) 4.4 oz
Output
Voltage Range
48 VDC Nominal 36 - 75 VDC
Undervoltage Lockout - Turn on / Turn off 34 / 32 VDC
Input
Efficiency vs. Load (48V Input)
Notes
†MTBF predictions may vary slightly from model to model.
Specifications typically at 25°C, normal line, and full load, unless otherwise stated.
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with
commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please consult factory
for specific model information.
REV. JUN 03, 2004
FES DC-DC Series Data Sheet
Single-Output, 300 Watts
Page 2 of 3
Mechanical Drawing
Thermal Impedance
Natural Convection 5.4 °C/W
100 LFM 3.8 °C/W
200 LFM 2.5 °C/W
300 LFM 1.7 °C/W
400 LFM 1.6 °C/W
Tolerances
Note:
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated
for specific application.
Pin Function
1-V
in
2 Case
3 Enable
4+V
in
5-V
out
6-V
out
7 -Sense
8 Trim
9 +Sense
10 +Vout
11 +Vout
Inches: (Millimeters)
.XX ± 0.020 .X ± 0.5
.XXX ± .010 .XX ± 0.25
Pin:
± 0.002 ± 0.05
(Dimensions as listed unless otherwise
specified.)
Model Selection
!
"" "
#$
#$
!
!
MODEL INPUT VOLTAGE INPUT VOLTAGE MAXIMUM INPUT OUTPUT RATED OUTPUT RIPPLE & NOISE TYPICAL
(VOLTS) RANGE (VOLTS) CURRENT (AMPS)* VOLTAGE (VOLTS) CURRENT (AMPS) pk-pk (mV) EFFICIENCY**
FES132ZE-A 48 36 - 75 4.5 3.3 40 100 87%
FES200ZG-A 48 36 - 75 6.5 5.0 40 100 80%
FES200ZE-A 48 36 - 75 7.0 3.3 60 100 81%
FES300ZG-A 48 36 - 75 10.5 5.0 60 100 84%
* Maximum input current at minimum input voltage, maximum rated output power.
** At nominal Vin, rated output.
Model numbers highlighted in yellow or shaded are not recommended for new designs.
REV. JUN 03, 2004
OPTIONS
Page 3 of 3
This page is offered as a reference. Consult factory for actual availability of options. When ordering
equipment options, use the following suffix information. Select preferred option(s) and add the suffix to the
model number. Ordering option examples are located below the options table.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president
of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
OPTION SUFFIX APPLICABLE SERIES REMARKS
Negative Logic N HAS, HBD, HBS, HES, HLS, HLD, LES, TTL "Low" Turns Module ON
QBS, QES, QLS, TES, TQD TTL "High" Turns Module OFF
Lucent-Compatible Trim T HAS, HBD, HBS, HES, HLS, QBS, QES,
QLS
Trim 1 IAS, LES
Enable 2 IAD, IAS, LES, SMS
Trim and Enable 3 IAS, LES
Pin Length and Heat Sink Options Standard Pin Length is 0.180" (4.6mm)
0.110" (2.8mm) Pin Length 8 All Leaded Models
0.150" (3.8mm) Pin Length 9 All Leaded Models
0.24" (6.1mm) Horizontal Heat Sink 1H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks Includes Thermal Pad
(Except HLS, HLD, QLS, TLD, and TKD Packages)
0.24" (6.1mm) Vertical Heat Sink 1V All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks Includes Thermal Pad
(Except HLS, HLD, QLS, TLD, and TKD Packages)
0.45" (11.4mm) Horizontal Heat Sink 2H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks Includes Thermal Pad
(Except HLS, HLD, QLS, TLD, and TKD Packages)
0.45" (11.4mm) Vertical Heat Sink 2V All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks Includes Thermal Pad
(Except HLS, HLD, QLS, TLD, and TKD Packages)
0.95" (24.1mm) Horizontal Heat Sink 3H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks Includes Thermal Pad
(Except HLS, HLD, QLS, TLD, and TKD Packages)
0.95" (24.1mm) Vertical Heat Sink 3V All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks Includes Thermal Pad
(Except HLS, HLD, QLS, TLD, and TKD Packages)
Example Options:
HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95” vertical heat sink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent-compatible trim and 0.110” pin length.
