W9725G6JB-25I - Winbond - Datasheet.Live

W9725G6JB

4M × 4 BANKS × 16 BIT DDR2 SDRAM

Publication Release Date: Mar. 10, 2010

- 1 - Revision A01

Table of Contents-

1. GENERAL DESCRIPTION ...................................................................................................................4

2. FEATURES...........................................................................................................................................4

3. KEY PARAMETERS .............................................................................................................................5

4. BALL CONFIGURATION ......................................................................................................................6

5. BALL DESCRIPTION............................................................................................................................7

6. BLOCK DIAGRAM ................................................................................................................................8

7. FUNCTIONAL DESCRIPTION..............................................................................................................9

7.1 Power-up and Initialization Sequence ...................................................................................................9

7.2 Mode Register and Extended Mode Registers Operation ...................................................................10

7.2.1 Mode Register Set Command (MRS)...............................................................................10

7.2.2 Extend Mode Register Set Commands (EMRS) ..............................................................11

7.2.2.1 Extend Mode Register Set Command (1), EMR (1)................................................11

7.2.2.2 DLL Enable/Disable................................................................................................12

7.2.2.3 Extend Mode Register Set Command (2), EMR (2)................................................13

7.2.2.4 Extend Mode Register Set Command (3), EMR (3)................................................14

7.2.3 Off-Chip Driver (OCD) Impedance Adjustment ................................................................15

7.2.3.1 Extended Mode Register for OCD Impedance Adjustment ....................................16

7.2.3.2 OCD Impedance Adjust ..........................................................................................16

7.2.3.3 Drive Mode .............................................................................................................17

7.2.4 On-Die Termination (ODT)...............................................................................................18

7.2.5 ODT related timings .........................................................................................................18

7.2.5.1 MRS command to ODT update delay.....................................................................18

7.3 Command Function.............................................................................................................................20

7.3.1 Bank Activate Command..................................................................................................20

7.3.2 Read Command...............................................................................................................20

7.3.3 Write Command ...............................................................................................................21

7.3.4 Burst Read with Auto-precharge Command.....................................................................21

7.3.5 Burst Write with Auto-precharge Command.....................................................................21

7.3.6 Precharge All Command ..................................................................................................21

7.3.7 Self Refresh Entry Command ..........................................................................................21

7.3.8 Self Refresh Exit Command.............................................................................................22

7.3.9 Refresh Command ...........................................................................................................22

7.3.10 No-Operation Command ..................................................................................................23

7.3.11 Device Deselect Command..............................................................................................23

7.4 Read and Write access modes ...........................................................................................................23

7.4.1 Posted CAS ....................................................................................................................23

7.4.1.1 Examples of posted CAS operation......................................................................23

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 2 - Revision A01

7.4.2 Burst mode operation.......................................................................................................24

7.4.3 Burst read mode operation...............................................................................................25

7.4.4 Burst write mode operation ..............................................................................................25

7.4.5 Write data mask ...............................................................................................................26

7.5 Burst Interrupt .....................................................................................................................................26

7.6 Precharge operation............................................................................................................................27

7.6.1 Burst read operation followed by precharge.....................................................................27

7.6.2 Burst write operation followed by precharge ....................................................................27

7.7 Auto-precharge operation ...................................................................................................................27

7.7.1 Burst read with Auto-precharge........................................................................................28

7.7.2 Burst write with Auto-precharge .......................................................................................28

7.8 Refresh Operation...............................................................................................................................29

7.9 Power Down Mode..............................................................................................................................29

7.9.1 Power Down Entry ...........................................................................................................30

7.9.2 Power Down Exit..............................................................................................................30

7.10 Input clock frequency change during precharge power down .............................................................30

8. OPERATION MODE ...........................................................................................................................31

8.1 Command Truth Table ........................................................................................................................31

8.2 Clock Enable (CKE) Truth Table for Synchronous Transitions............................................................32

8.3 Data Mask (DM) Truth Table...............................................................................................................32

8.4 Function Truth Table ...........................................................................................................................33

8.5 Simplified Stated Diagram...................................................................................................................36

9. ELECTRICAL CHARACTERISTICS ...................................................................................................37

9.1 Absolute Maximum Ratings.................................................................................................................37

9.2 Operating Temperature Condition.......................................................................................................37

9.3 Recommended DC Operating Conditions ...........................................................................................37

9.4 ODT DC Electrical Characteristics ......................................................................................................38

9.5 Input DC Logic Level...........................................................................................................................38

9.6 Input AC Logic Level ...........................................................................................................................38

9.7 Capacitance ........................................................................................................................................39

9.8 Leakage and Output Buffer Characteristics ........................................................................................39

9.9 DC Characteristics ..............................................................................................................................40

9.10 IDD Measurement Test Parameters....................................................................................................42

9.11 AC Characteristics ..............................................................................................................................43

9.11.1 AC Characteristics and Operating Condition for -18 speed grade ...................................43

9.11.2 AC Characteristics and Operating Condition for -25/25I/25A/-3 speed grade ..................45

9.12 AC Input Test Conditions ....................................................................................................................65

9.13 Differential Input/Output AC Logic Levels ...........................................................................................65

9.14 AC Overshoot / Undershoot Specification...........................................................................................66

9.14.1 AC Overshoot / Undershoot Specification for Address and Control Pins: ........................66

9.14.2 AC Overshoot / Undershoot Specification for Clock, Data, Strobe and Mask pins:..........66

10. TIMING WAVEFORMS .......................................................................................................................67

10.1 Command Input Timing.......................................................................................................................67

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 3 - Revision A01

10.2 Timing of the CLK Signals...................................................................................................................67

10.3 ODT Timing for Active/Standby Mode.................................................................................................68

10.4 ODT Timing for Power Down Mode ....................................................................................................68

10.5 ODT Timing mode switch at entering power down mode....................................................................69

10.6 ODT Timing mode switch at exiting power down mode ......................................................................70

10.7 Data output (read) timing ....................................................................................................................71

10.8 Burst read operation: RL=5 (AL=2, CL=3, BL=4) ................................................................................71

10.9 Data input (write) timing ......................................................................................................................72

10.10 Burst write operation: RL=5 (AL=2, CL=3, WL=4, BL=4)...........................................................72

10.11 Seamless burst read operation: RL = 5 ( AL = 2, and CL = 3, BL = 4) ......................................73

10.12 Seamless burst write operation: RL = 5 ( WL = 4, BL = 4).........................................................73

10.13 Burst read interrupt timing: RL =3 (CL=3, AL=0, BL=8).............................................................74

10.14 Burst write interrupt timing: RL=3 (CL=3, AL=0, WL=2, BL=8) ..................................................74

10.15 Write operation with Data Mask: WL=3, AL=0, BL=4) ...............................................................75

10.16 Burst read operation followed by precharge: RL=4 (AL=1, CL=3, BL=4, tRTP ≤ 2clks) ............76

10.17 Burst read operation followed by precharge: RL=4 (AL=1, CL=3, BL=8, tRTP ≤ 2clks) ............76

10.18 Burst read operation followed by precharge: RL=5 (AL=2, CL=3, BL=4, tRTP ≤ 2clks) ............77

10.19 Burst read operation followed by precharge: RL=6 (AL=2, CL=4, BL=4, tRTP ≤ 2clks) ............77

10.20 Burst read operation followed by precharge: RL=4 (AL=0, CL=4, BL=8, tRTP > 2clks) ............78

10.21 Burst write operation followed by precharge: WL = (RL-1) = 3 ..................................................78

10.22 Burst write operation followed by precharge: WL = (RL-1) = 4 ..................................................79

10.23 Burst read operation with Auto-precharge: RL=4 (AL=1, CL=3, BL=8, tRTP ≤ 2clks) ...............79

10.24 Burst read operation with Auto-precharge: RL=4 (AL=1, CL=3, BL=4, tRTP > 2clks) ...............80

10.25 Burst read with Auto-precharge followed by an activation to the same bank (tRC Limit): RL=5

(AL=2, CL=3, internal tRCD=3, BL=4, tRTP ≤ 2clks).......................................................................................80

10.26 Burst read with Auto-precharge followed by an activation to the same bank (tRP Limit): RL=5

(AL=2, CL=3, internal tRCD=3, BL=4, tRTP ≤ 2clks).......................................................................................81

10.27 Burst write with Auto-precharge (tRC Limit): WL=2, WR=2, BL=4, tRP=3.................................81

10.28 Burst write with Auto-precharge (WR + tRP Limit): WL=4, WR=2, BL=4, tRP=3.......................82

10.29 Self Refresh Timing ...................................................................................................................82

10.30 Active Power Down Mode Entry and Exit Timing.......................................................................83

10.31 Precharged Power Down Mode Entry and Exit Timing ..............................................................83

10.32 Clock frequency change in precharge Power Down mode ........................................................84

11. PACKAGE SPECIFICATION ..............................................................................................................85

Package Outline WBGA-84 (8x12.5 mm2).......................................................................................................85

12. REVISION HISTORY ..........................................................................................................................86

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 4 - Revision A01

1. GENERAL DESCRIPTION

The W9725G6JB is a 256M bits DDR2 SDRAM, organized as 4,194,304 words × 4 banks × 16 bits.

This device achieves high speed transfer rates up to 1066Mb/sec/pin (DDR2-1066) for general

applications. W9725G6JB is sorted into the following speed grades: -18, -25, 25I, 25A and -3. The -18

is compliant to the DDR2-1066 (7-7-7) specification. The -25/25I/25A are compliant to the DDR2-800

(5-5-5) or DDR2-800 (6-6-6) specification (the 25I industrial grade and 25A automotive grade which is

guaranteed to support -40°C ≤ T

CASE ≤ 95°C). The -3 is compliant to the DDR2-667 (5-5-5)

specification.

All of the control and address inputs are synchronized with a pair of externally supplied differential

clocks. Inputs are latched at the cross point of differential clocks (CLK rising and CLK falling). All

I/Os are synchronized with a single ended DQS or differential DQS- DQS pair in a source

synchronous fashion.

2. FEATURES

z Power Supply: VDD, VDDQ = 1.8 V ± 0.1 V

z Double Data Rate architecture: two data transfers per clock cycle

z CAS Latency: 3, 4, 5, 6 and 7

z Burst Length: 4 and 8

z Bi-directional, differential data strobes (DQS and DQS ) are transmitted / received with data

z Edge-aligned with Read data and center-aligned with Write data

z DLL aligns DQ and DQS transitions with clock

z Differential clock inputs (CLK and CLK )

z Data masks (DM) for write data

z Commands entered on each positive CLK edge, data and data mask are referenced to both edges

of DQS

z Posted CAS programmable additive latency supported to make command and data bus efficiency

z Read Latency = Additive Latency plus CAS Latency (RL = AL + CL)

z Off-Chip-Driver impedance adjustment (OCD) and On-Die-Termination (ODT) for better signal

quality

z Auto-precharge operation for read and write bursts

z Auto Refresh and Self Refresh modes

z Precharged Power Down and Active Power Down

z Write Data Mask

z Write Latency = Read Latency - 1 (WL = RL - 1)

z Interface: SSTL_18

z Packaged in WBGA 84 Ball (8X12.5 mm2), using Lead free materials with RoHS compliant

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 5 - Revision A01

3. KEY PARAMETERS

SPEED GRADE DDR2-1066 DDR2-800 DDR2-667

Bin(CL-tRCD-tRP) 7-7-7 5-5-5/6-6-6 5-5-5

SYM.

Part Number Extension -18 -25/25I/25A -3

Min. 1.875 nS − −

@CL = 7 Max. 7.5 nS − −

Min. 2.5 nS 2.5 nS −

@CL = 6 Max. 7.5 nS 8 nS −

Min. 3 nS 2.5 nS 3 nS

@CL = 5 Max. 7.5 nS 8 nS 8 nS

Min. 3.75 nS 3.75 nS 3.75 nS

@CL = 4 Max. 7.5 nS 8 nS 8 nS

Min. − 5 nS 5 nS

tCK(avg) Average clock period

@CL = 3 Max. − 8 nS 8 nS

tRCD Active to Read/Write Command Delay Time Min. 13.125 nS 12.5 nS 15 nS

tRP Precharge to Active Command Period Min. 13.125 nS 12.5 nS 15 nS

tRC Active to Ref/Active Command Period Min. 53.125 nS 52.5 nS 55 nS

tRAS Active to Precharge Command Period Min. 40 nS 40 nS 40 nS

IDD0 Operating current Max. 70 mA 60 mA 55 mA

IDD1 Operation current (Single bank) Max. 80 mA 70 mA 65 mA

IDD4R Operating burst read current Max. 125 mA 105 mA 95 mA

IDD4W Operating burst write current Max. 130 mA 110 mA 100 mA

IDD5B Burst refresh current Max. 75 mA 70 mA 65 mA

IDD6 Self refresh current Max. 6 mA 6 mA 6 mA

IDD7 Operating bank interleave read current Max. 160 mA 135 mA 115 mA

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 6 - Revision A01

4. BALL CONFIGURATION

123456789

VSSQ

UDQS

VDDQ

LDQS

VDDQ

CAS

UDQS

VSSQ

DQ8

VSSQ

DQ0

CLK

VDDQ

DQ7

VDD

ODT

VDD

DQ14

VDDQ

DQ12

VDDL

VSSQ

DQ9

VSSQ

CKE

BA0 BA1

DQ3

LDM

VSS

DQ11

VDDQ

VSS

UDM

VDD

DQ6

VDDQ

DQ4

VSS

VDD A12 NC NCNC

A11 A8A9A7

A10/AP

VSSVREF

DQ1

VSSQ

VDDQ

VSSQ

NC VSSQ LDQS

VSSQDQ10

DQ15

DQ13

VDDQ

DQ5

VDD

VSS

VSSQ

DQ2

VSSDL

RAS

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 7 - Revision A01

5. BALL DESCRIPTION

BALL NUMBER SYMBOL FUNCTION DESCRIPTION

M8,M3,M7,N2,N8,N3

,N7,P2,P8,P3,M2,P7

,R2

A0−A12 Address

Provide the row address for active commands, and the column

address and Auto-precharge bit for Read/Write commands to select

one location out of the memory array in the respective bank.

Row address: A0−A12.

Column address: A0−A8. (A10 is used for Auto-precharge)

L2,L3 BA0−BA1 Bank Select

BA0−BA1 define to which bank an ACTIVE, READ, WRITE or

PRECHARGE command is being applied.

G8,G2,H7,H3,H1,H9

,F1,F9,C8,C2,D7,D3,

D1,D9,B1,B9

DQ0−DQ15 Data Input

/ Output Bi-directional data bus.

K9 ODT

On Die Termination

Control

ODT (registered HIGH) enables termination resistance internal to the

DDR2 SDRAM.

F7,E8

LDQS,

LDQS LOW Data Strobe

Data Strobe for Lower Byte: Output with read data, input with write

data for source synchronous operation. Edge-aligned with read data,

center-aligned with write data. LDQS corresponds to the data on

DQ0−DQ7. LDQS is only used when differential data strobe mode

is enabled via the control bit at EMR (1)[A10 EMRS command].

B7,A8

UDQS,

UDQS UP Data Strobe

Data Strobe for Upper Byte: Output with read data, input with write

data for source synchronous operation. Edge-aligned with read data,

center-aligned with write data. UDQS corresponds to the data on

DQ8−DQ15. UDQS is only used when differential data strobe mode

is enabled via the control bit at EMR (1)[A10 EMRS command].

L8 CS Chip Select

All commands are masked when CS is registered

HIGH.CS provides for external bank selection on systems with

multiple ranks. CS is considered part of the command code.

K7,L7,K3 RAS , CAS ,

Command Inputs RAS ,CAS and WE (along with CS ) define the command being

entered.

B3,F3

UDM

LDM Input Data Mask

DM is an input mask signal for write data. Input data is masked when

DM is sampled high coincident with that input data during a Write

access. DM is sampled on both edges of DQS. Although DM pins are

input only, the DM loading matches the DQ and DQS loading.

J8,K8 CLK,

CLK

Differential Clock

Inputs

CLK and CLK are differential clock inputs. All address and control

input signals are sampled on the crossing of the positive edge of CLK

and negative edge of CLK . Output (read) data is referenced to the

crossings of CLK and CLK (both directions of crossing).

K2 CKE Clock Enable

CKE (registered HIGH) activates and CKE (registered LOW)

deactivates clocking circuitry on the DDR2 SDRAM.

J2 VREF Reference Voltage VREF is reference voltage for inputs.

A1,E1,J9,M9,R1 VDD Power Supply

Power Supply: 1.8V ± 0.1V.

A3,E3,J3,N1,P9 VSS Ground Ground.

A9,C1,C3,C7,C9,E9,

G1,G3,G7,G9 VDDQ DQ Power Supply DQ Power Supply: 1.8V ± 0.1V.

A7,B2,B8,D2,D8,E7,

F2,F8,H2,H8 VSSQ DQ Ground DQ Ground. Isolated on the device for improved noise immunity.

A2,E2,L1,R3,R7,R8 NC No Connection No connection.

J7 VSSDL DLL Ground DLL Ground.

J1 VDDL DLL Power Supply DLL Power Supply: 1.8V ± 0.1V.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 8 - Revision A01

6. BLOCK DIAGRAM

CKE

A10

DLL

CLOCK

BUFFER

COMMAND

DECODER

ADDRESS

BUFFER

REFRESH

COUNTER

COLUMN

COUNTER

CONTROL

SIGNAL

GENERATOR

MODE

COLUMN DECODER

SENSE AMPLIFIER

CELL ARRAY

BANK #2

COLUMN DECODER

SENSE AMPLIFIER

CELL ARRAY

BANK #0

COLUMN DECODER

SENSE AMPLIFIER

CELL ARRAY

BANK #3

DATA CONTROL

CIRCUIT

BUFFER

COLUMN DECODER

SENSE AMPLIFIER

CELL ARRAY

BANK #1

NOTE: The cell array configuration is 8192 * 512 * 16

ROW DECODER ROW DECODER

ROW DECODERROW DECODER

A11

A12

BA1

BA0

RAS

CAS

CLK

PREFETCH REGISTER

ODT

CONTROL

DQ0

DQ15

LDQS

UDQS

LDM

UDM

ODT

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 9 - Revision A01

7. FUNCTIONAL DESCRIPTION

7.1 Power-up and Initialization Sequence

DDR2 SDRAMs must be powered up and initialized in a predefined manner. Operational procedures

other than those specified may result in undefined operation. The following sequence is required for

Power-up and Initialization.

1. Apply power and attempt to maintain CKE below 0.2 × VDDQ and ODT*1 at a LOW state (all other

inputs may be undefined.) Either one of the following sequence is required for Power-up.

A. The VDD voltage ramp time must be no greater than 200 mS from when VDD ramps from 300

mV to VDD min; and during the VDD voltage ramp, |VDD -VDDQ| ≦ 0.3 volts.

z VDD, VDDL and VDDQ are driven from a single power converter output

z VTT is limited to 0.95V max

z VREF*2 tracks VDDQ/2

z VDDQ ≧ VREF must be met at all times

B. Voltage levels at I/Os and outputs must be less than VDDQ during voltage ramp time to avoid

DRAM latch-up. During the ramping of the supply voltages, VDD ≧ VDDL ≧ VDDQ must be

maintained and is applicable to both AC and DC levels until the ramping of the supply voltages

is complete.

z Apply VDD/VDDL*3 before or at the same time as VDDQ

z Apply VDDQ*4 before or at the same time as VTT

z VREF*2 tracks VDDQ/2

z VDDQ ≧ VREF must be met at all times.

2. Start Clock and maintain stable condition for 200 µS (min.).

3. After stable power and clock (CLK, CLK ), apply NOP or Deselect and take CKE HIGH.

4. Wait minimum of 400 nS then issue precharge all command. NOP or Deselect applied during 400

nS period.

5. Issue an EMRS command to EMR (2). (To issue EMRS command to EMR (2), provide LOW to

BA0, HIGH to BA1.)

6. Issue an EMRS command to EMR (3). (To issue EMRS command to EMR (3), provide HIGH to

BA0 and BA1.)

7. Issue EMRS to enable DLL. (To issue DLL Enable command, provide LOW to A0, HIGH to BA0

and LOW to BA1. And A9=A8=A7=LOW must be used when issuing this command.)

8. Issue a Mode Register Set command for DLL reset. (To issue DLL Reset command, provide HIGH

to A8 and LOW to BA0 and BA1.)

9. Issue a precharge all command.

10. Issue 2 or more Auto Refresh commands.

11. Issue a MRS command with LOW to A8 to initialize device operation. (i.e. to program operating

parameters without resetting the DLL.)

12. At least 200 clocks after step 8, execute OCD Calibration (Off Chip Driver impedance adjustment).

If OCD calibration is not used, EMRS to EMR (1) to set OCD Calibration Default

(A9=A8=A7=HIGH) followed by EMRS to EMR (1) to exit OCD Calibration Mode

(A9=A8=A7=LOW) must be issued with other operating parameters of EMR(1).

13. The DDR2 SDRAM is now ready for normal operation.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 10 - Revision A01

Notes:

1. To guarantee ODT off, VREF must be valid and a LOW level must be applied to the ODT pin.

2. VREF must be within ± 300 mV with respect to VDDQ/2 during supply ramp time.

3. VDD/VDDL voltage ramp time must be no greater than 200 mS from when VDD ramps from 300 mV to VDD min.

4. The VDDQ voltage ramp time from when VDD min is achieved on VDD to when VDDQ min is achieved on VDDQ must be no

greater than 500 mS

tCH tCL

tIS

400nS

NOP PRE

ALL EMRS MRS PRE

ALL REF MRSREF EMRS EMRS ANY

CMD

tRP tMRD tMRD

tRP tRFC tRFC tOIT

Follow OCD

Flow chart

OCD

CAL. Mode

Exit

OCD

Default

min 200 Cycle

DLL

Reset

DLL

Enable

CLK

CKE

Command

ODT

tMRD

Figure 1—Initialization sequence after power-up

7.2 Mode Register and Extended Mode Registers Operation

For application flexibility, burst length, burst type, CAS Latency, DLL reset function, write recovery

time (WR) are user defined variables and must be programmed with a Mode Register Set (MRS)

command. Additionally, DLL disable function, driver impedance, additive CAS Latency, ODT (On Die

Termination), single-ended strobe and OCD (off chip driver impedance adjustment) are also user

defined variables and must be programmed with an Extended Mode Register Set (EMRS) command.

Contents of the Mode Register (MR) or Extended Mode Registers EMR (1), EMR (2) and EMR (3) can

be altered by re-executing the MRS or EMRS Commands. Even if the user chooses to modify only a

subset of the MR or EMR (1), EMR (2) and EMR (3) variables, all variables within the addressed

MRS, EMRS and Reset DLL do not affect array contents, which mean re-initialization including those

can be executed at any time after power-up without affecting array contents.

7.2.1 Mode Register Set Command (MRS)

(CS = "L", RAS = "L", CAS = "L", WE = "L", BA0 = "L", BA1 = "L", A0 to A12 = Register Data)

The mode register stores the data for controlling the various operating modes of DDR2 SDRAM. It

programs CAS Latency, burst length, burst sequence, test mode, DLL reset, Write Recovery (WR) and

various vendor specific options to make DDR2 SDRAM useful for various applications. The default

value in the Mode Register after power-up is not defined, therefore the Mode Register must be

programmed during initialization for proper operation.

The DDR2 SDRAM should be in all bank precharge state with CKE already HIGH prior to writing into

the mode register. The mode register set command cycle time (tMRD) is required to complete the write

operation to the mode register. The mode register contents can be changed using the same command

and clock cycle requirements during normal operation as long as all banks are in the precharge state.

The mode register is divided into various fields depending on functionality. Burst length is defined by

A[2:0] with options of 4 and 8 bit burst lengths. The burst length decodes are compatible with DDR

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 11 - Revision A01

SDRAM. Burst address sequence type is defined by A3, CAS Latency is defined by A[6:4]. The DDR2

does not support half clock latency mode. A7 is used for test mode. A8 is used for DLL reset. A7 must

be set to LOW for normal MRS operation. Write recovery time WR is defined by A[11:9]. Refer to the

table for specific codes.

DDR2-667

DDR2-800

DDR2-1066

DDR2-800

DDR2-1066

DDR2-667

Note:

1. WR (write recovery for Auto-precharge) min is determined by tCK(avg) max and WR max is determined by tCK(avg) min.

WR[cycles] = RU{ tWR[nS] / tCK(avg)[nS] }, where RU stands for round up. The mode register must be programmed to this

value. This is also used with tRP to determine tDAL.

Figure 2—Mode Register Set (MRS)

7.2.2 Extend Mode Register Set Commands (EMRS)

7.2.2.1 Extend Mode Register Set Command (1), EMR (1)

(CS = "L", RAS = "L", CAS = "L", WE = "L", BA0 = "H", BA1 = "L", A0 to A12 = Register data)

The extended mode register (1) stores the data for enabling or disabling the DLL, output driver

strength, additive latency, ODT, DQS disable, OCD program. The default value of the extended

mode register (1) is not defined, therefore the extended mode register (1) must be programmed during

initialization for proper operation. The DDR2 SDRAM should be in all bank precharge with CKE

already high prior to writing into the extended mode register (1). The mode register set command

cycle time (tMRD) must be satisfied to complete the write operation to the extended mode register (1).

Extended mode register (1) contents can be changed using the same command and clock cycle

requirements during normal operation as long as all banks are in the precharge state. A0 is used for

DLL enable or disable. A1 is used for enabling a reduced strength output driver. A[5:3] determines the

additive latency, A[9:7] are used for OCD control, A10 is used for DQS disable. A2 and A6 are used

for ODT setting.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 12 - Revision A01

7.2.2.2 DLL Enable/Disable

The DLL must be enabled for normal operation. DLL enable is required during power-up initialization,

and upon returning to normal operation after having the DLL disabled. The DLL is automatically

disabled when entering Self Refresh operation and is automatically re-enabled and reset upon exit of

Self Refresh operation. Any time the DLL is enabled (and subsequently reset), 200 clock cycles must

occur before a Read command can be issued to allow time for the internal clock to be synchronized

with the external clock. Failing to wait for synchronization to occur may result in a violation of the tAC

or tDQSCK parameters.

BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0

0 1 OCD program BTRtt

Address Field

Extended Mode Register (1)

BA1 BA0 MRS mode

EMR (1)

EMR (2)

EMR (3)

A6 A2

Additive Latency

Qoff 0*1DQS Rtt D.I.C DLL

Rtt (nominal)

ODT Disabled

75 ohm

150 ohm

50 ohm*2

DLL Enable

Enable

Disable

OCD Calibration Program

OCD calibration mode exit; matain setting

Adjust mode*3

OCD Calibration default*4

Drive (1)

Drive (0)

A9 A8 A7

000

100

Driver impedance adjustment

A12

0 Output buffer enabled

Qoff (Optional)*5

Output buffer disabled

A10

DQS

Enable

Disable

A10

(DQS Enable)

0 (Enable)

1 (Disable)

Strobe Function Matrix

DQS

Hi-z

Output driver

impedance control

Reduced

Normal

Latency

Reserved

Output Driver Impedance Control

Driver

size

100%

60%

Additive Latency

DDR2-/667/800

DDR2-1066

Notes:

1. A11 default is “0 “ RDQS disabled.

2. Optional for DDR2-667, mandatory for DDR2-800 and DDR2-1066.

3. When Adjust mode is issued, AL from previously set value must be applied.

4. After setting to default, OCD calibration mode needs to be exited by setting A9-A7 to 000. Refer to the section 7.2.3 for

detailed information.

5. Output disabled - DQs, LDQS, LDQS , UDQS, UDQS . This feature is used in conjunction with DIMM IDD measurements

when IDDQ is not desired to be included.

Figure 3—EMR (1)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 13 - Revision A01

7.2.2.3 Extend Mode Register Set Command (2), EMR (2)

(CS = "L", RAS = "L", CAS = "L", WE = "L", BA0 = "L", BA1 = "H", A0 to A12 = Register data)

The extended mode register (2) controls refresh related features. The default value of the extended

mode register (2) is not defined, therefore the extended mode register (2) must be programmed during

initialization for proper operation.

The DDR2 SDRAM should be in all bank precharge state with CKE already high prior to writing into

the extended mode register (2). The mode register set command cycle time (tMRD) must be satisfied to

complete the write operation to the extended mode register (2). Mode register contents can be

changed using the same command and clock cycle requirements during normal operation as long as

all banks are in the precharge state.

A12A11A10A9A8A7A6A5A4A3A2A1A0

0 SELF

0*1

Address Field

Extended Mode Register (2)

0*1

0Disable

High Temperature Self Refresh Rate Enable

Enable*2

BA0

BA1 BA0 MRS mode

MRS

EMR (1)

EMR (2)

EMR (3)

BA1

Notes:

1. The rest bits in EMR (2) is reserved for future use and all bits in EMR (2) except A7, BA0 and BA1 must be programmed to 0

when setting the extended mode register (2) during initialization.

2. When DRAM is operated at 85 °C < TCASE ≤ 95 °C the extended Self Refresh rate must be enabled by setting bit A7 to "1"

before the Self Refresh mode can be entered.

Figure 4—EMR (2)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 14 - Revision A01

7.2.2.4 Extend Mode Register Set Command (3), EMR (3)

(CS = "L", RAS = "L", CAS = "L", WE = "L", BA0 = "H", BA1 = "H", A0 to A12 = Register data)

No function is defined in extended mode register (3). The default value of the EMR (3) is not defined,

therefore the EMR (3) must be programmed during initialization for proper operation.

BA1BA0A12A11A10A9A8A7A6A5A4A3A2A1A0

Address Field

Extended Mode Register (3)

0*1

Note:

1. All bits in EMR (3) except BA0 and BA1 are reserved for future use and must be set to 0 when programming the EMR (3).

Figure 5—EMR (3)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 15 - Revision A01

7.2.3 Off-Chip Driver (OCD) Impedance Adjustment

DDR2 SDRAM supports driver calibration feature and the flow chart in Figure 6 is an example of the

sequence. Every calibration mode command should be followed by “OCD calibration mode exit”

before any other command being issued. MRS should be set before entering OCD impedance

adjustment and On Die Termination (ODT) should be carefully controlled depending on system

environment.

Start

ALL OK

All MR shoud be programmed before entering OCD impedance adjustment and ODT should

be carefully controlled depending on system environment

EMRS: Drive(0)

DQ &DQS Low; DQS High

EMRS: OCD calibration mode exit

Test

Need Calibration

EMRS: OCD calibration mode exit

EMRS:

Enter Adjust Mode

BL=4 code input to all DQs

Inc, Dec or NOP

EMRS: OCD calibration mode exit

ALL OK

EMRS: Drive(1)

DQ &DQS High; DQS Low

Test

Need Calibration

EMRS: OCD calibration mode exit

EMRS:

Enter Adjust Mode

BL=4 code input to all DQs

Inc, Dec or NOP

EMRS: OCD calibration mode exit

End

Figure 6—OCD Impedance Adjustment Flow Chart

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 16 - Revision A01

7.2.3.1 Extended Mode Register for OCD Impedance Adjustment

OCD impedance adjustment can be done using the following EMRS mode. In drive mode all outputs

are driven out by DDR2 SDRAM. In Drive (1) mode, all DQ, DQS signals are driven HIGH and all

DQS signals are driven LOW. In Drive (0) mode, all DQ, DQS signals are driven LOW and all DQS

signals are driven HIGH. In adjust mode, BL = 4 of operation code data must be used. In case of OCD

calibration default, output driver characteristics have a nominal impedance value of 18 Ohms during

nominal temperature and voltage conditions. OCD applies only to normal full strength output drive

setting defined by EMR (1) and if reduced strength is set, OCD default driver characteristics are not

applicable. When OCD calibration adjust mode is used, OCD default output driver characteristics are

not applicable. After OCD calibration is completed or driver strength is set to default, subsequent

EMRS commands not intended to adjust OCD characteristics must specify A[9:7] as ’000’ in order to

maintain the default or calibrated value.

Table 1—OCD Drive Mode Program

A9 A8 A7 Operation

0 0 0 OCD calibration mode exit

0 0 1

Drive (1) DQ, DQS HIGH and DQS LOW

0 1 0

Drive (0) DQ, DQS LOW and DQS HIGH

1 0 0 Adjust mode

1 1 1 OCD calibration default

7.2.3.2 OCD Impedance Adjust

To adjust output driver impedance, controllers must issue the ADJUST EMRS command along with a

4 bit burst code to DDR2 SDRAM as in table 2. For this operation, Burst Length has to be set to BL =

4 via MRS command before activating OCD and controllers must drive the burst code to all DQs at the

same time. DT0 in table 2 means all DQ bits at bit time 0, DT1 at bit time 1, and so forth. The driver

output impedance is adjusted for all DDR2 SDRAM DQs simultaneously and after OCD calibration, all

DQs and DQS’s of a given DDR2 SDRAM will be adjusted to the same driver strength setting. The

maximum step count for adjustment is 16 and when the limit is reached, further increment or

decrement code has no effect. The default setting may be any step within the 16 step range. When

Adjust mode command is issued, AL from previously set value must be applied.

Table 2—OCD Adjust Mode Program

4 bit burst code inputs to all DQs Operation

DT0 DT1 DT2 DT3 Pull-up driver strength Pull-down driver strength

0 0 0 0 NOP (No operation) NOP (No operation)

0 0 0 1 Increase by 1 step NOP

0 0 1 0 Decrease by 1 step NOP

0 1 0 0 NOP Increase by 1 step

1 0 0 0 NOP Decrease by 1 step

0 1 0 1 Increase by 1 step Increase by 1 step

0 1 1 0 Decrease by 1 step Increase by 1 step

1 0 0 1 Increase by 1 step Decrease by 1 step

1 0 1 0 Decrease by 1 step Decrease by 1 step

Other Combinations Reserved

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 17 - Revision A01

For proper operation of adjust mode, WL = RL - 1 = AL + CL - 1 clocks and tDS/tDH should be met as

shown in Figure 7. For input data pattern for adjustment, DT0 - DT3 is a fixed order and is not affected

by burst type (i.e., sequential or interleave).

OCD adjust mode OCD calibration mode exit

WL DQS

tDS tDH

DT0

EMRS(1) NOPNOPNOPNOPNOPNOP

CLK

DQS_in

CMD

DQ_in

NOP

EMRSNOP

NOP

NOPEMRS

CLK

DT1 DT2 DT3

Figure 7—OCD Adjust Mode

7.2.3.3 Drive Mode

Drive mode, both Drive (1) and Drive (0), is used for controllers to measure DDR2 SDRAM Driver

impedance. In this mode, all outputs are driven out tOIT after “enter drive mode” command and all

output drivers are turned-off tOIT after “OCD calibration mode exit” command as shown in Figure 8.

Enter Drive mode OCD calibration mode exit

EMRSEMRS NOP NOP NOP NOP NOPNOP NOP

CLK

DQS

CMD

tOIT tOIT

DQs high for Drive (1)

DQs low for Drive (0)

DQS high & DQS low for Drive (1), DQS low & DQS high for Drive (0)

CLK

HI-Z

Figure 8—OCD Drive Mode

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 18 - Revision A01

7.2.4 On-Die Termination (ODT)

On-Die Termination (ODT) is a new feature on DDR2 components that allows a DRAM to turn on/off

termination resistance for each DQ, UDQS/UDQS , LDQS/LDQS , UDM and LDM signal via the ODT

control pin. UDQS and LDQS are terminated only when enabled in the EMR (1) by address bit A10 =

0. The ODT feature is designed to improve signal integrity of the memory channel by allowing the

DRAM controller to independently turn on/off termination resistance for any or all DRAM devices.

The ODT function can be used for all active and standby modes. ODT is turned off and not supported

in Self Refresh mode. (Example timing waveforms refer to 10.3, 10.4 ODT Timing for

Active/Standby/Power Down Mode and 10.5, 10.6 ODT timing mode switch at entering/exiting power

down mode diagram in Chapter 10)

DRAM

Input

Buffer

Input

VDDQ

sw1

Rval3

VDDQ VDDQ

sw2 sw3

Rval1 Rval2

Rval1 Rval2 Rval3

sw1 sw2 sw3

VSSQ VSSQ VSSQ

Switch (sw1, sw2, sw3) is enabled by ODT pin.

Selection among sw1, sw2, and sw3 is determined by “Rtt (nominal)” in EMR (1).

Termination included on all DQs, DM, DQS, DQS pins.

Figure 9—Functional Representation of ODT

7.2.5 ODT related timings

7.2.5.1 MRS command to ODT update delay

During normal operation the value of the effective termination resistance can be changed with an

EMRS command. The update of the Rtt setting is done between tMOD,min and tMOD,max, and CKE

must remain HIGH for the entire duration of tMOD window for proper operation. The timings are shown

in the following timing diagram.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 19 - Revision A01

CMD

CLK

ODT

Rtt Updating New setting

tIS

tMOD,min

tMOD,max

tAOFD

EMRS NOP NOP NOP NOP NOP

Old setting

1) EMRS command directed to EMR(1), which updates the information in EMR(1)[A6,A2], i.e. Rtt (Nominal).

2) “setting” in this diagram is the Register and I/O setting, not what is measured from outside.

Figure 10—ODT update delay timing - tMOD

However, to prevent any impedance glitch on the channel, the following conditions must be met.

z tAOFD must be met before issuing the EMRS command.

z ODT must remain LOW for the entire duration of tMOD window, until tMOD,max is met.

Now the ODT is ready for normal operation with the new setting, and the ODT signal may be raised

again to turned on the ODT. Following timing diagram shows the proper Rtt update procedure.

CLK

CMD

ODT

Rtt Old setting New setting

tAOND

tIS

tMOD,max

tAOFD

EMRS NOP NOP NOP NOP NOP

1) EMRS command directed to EMR(1), which updates the information in EMR(1)[A6,A2], i.e. Rtt (Nominal).

2)“setting＂in this diagram is what is measured from outside.

Figure 11—ODT update delay timing - tMOD, as measured from outside

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 20 - Revision A01

7.3 Command Function

7.3.1 Bank Activate Command

(CS = "L", RAS = "L", CAS = "H", WE = "H", BA0, BA1 = Bank, A0 to A12 be row address)

The Bank Activate command must be applied before any Read or Write operation can be executed.

Immediately after the bank active command, the DDR2 SDRAM can accept a read or write command

on the following clock cycle. If a Read/Write command is issued to a bank that has not satisfied the

tRCDmin specification, then additive latency must be programmed into the device to delay when the

Read/Write command is internally issued to the device. The additive latency value must be chosen to

assure tRCDmin is satisfied. Additive latencies of 0, 1, 2, 3, 4, 5 and 6 are supported. Once a bank has

been activated it must be precharged before another Bank Activate command can be applied to the

same bank. The bank active and precharge times are defined as tRAS and tRP, respectively. The

minimum time interval between successive Bank Activate commands to the same bank is determined

by the RAS cycle time of the device (tRC). The minimum time interval between Bank Activate

commands is tRRD.

Figure 12—Bank activate command cycle: tRCD = 3, AL = 2, tRP = 3, tRRD = 2, tCCD = 2

7.3.2 Read Command

(CS = "L", RAS = "H", CAS = "L", WE = "H", BA0, BA1 = Bank, A10 = "L", A0 to A8 = Column

Address)

The READ command is used to initiate a burst read access to an active row. The value on BA0, BA1

inputs selects the bank, and the A0 to A8 address inputs determine the starting column address. The

address input A10 determines whether or not Auto-precharge is used. If Auto-precharge is selected,

the row being accessed will be precharged at the end of the READ burst; if Auto-precharge is not

selected, the row will remain open for subsequent accesses.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 21 - Revision A01

7.3.3 Write Command

(CS = "L", RAS = "H", CAS = "L", WE = "L", BA0, BA1 = Bank, A10 = "L", A0 to A8 = Column

Address)

The WRITE command is used to initiate a burst write access to an active row. The value on BA0, BA1

inputs selects the bank, and the A0 to A8 address inputs determine the starting column address. The

address input A10 determines whether or not Auto-precharge is used. If Auto-precharge is selected,

the row being accessed will be precharged at the end of the WRITE burst; if Auto-precharge is not

selected, the row will remain open for subsequent accesses.

7.3.4 Burst Read with Auto-precharge Command

(CS = "L", RAS = "H", CAS ="L", WE = "H", BA0, BA1 = Bank, A10 = "H", A0 to A8 = Column

Address)

If A10 is HIGH when a Read Command is issued, the Read with Auto-precharge function is engaged.

The DDR2 SDRAM starts an Auto-precharge operation on the rising edge which is (AL + BL/2) cycles

later than the read with AP command if tRAS(min) and tRTP(min) are satisfied.

7.3.5 Burst Write with Auto-precharge Command

(CS = "L", RAS = "H", CAS = "L", WE = "L", BA0, BA1 = Bank, A10 = "H", A0 to A8 = Column

Address)

If A10 is HIGH when a Write Command is issued, the Write with Auto-precharge function is engaged.

The DDR2 SDRAM automatically begins precharge operation after the completion of the burst write

plus write recovery time (WR) programmed in the mode register.

7.3.6 Precharge All Command

(CS = "L", RAS = "L", CAS = "H", WE = "L", BA0, BA1 = Don’t Care, A10 = "H", A0 to A9 and

A11 to A12 = Don’t Care)

The Precharge All command precharge all banks simultaneously. Then all banks are switched to the

idle state.

7.3.7 Self Refresh Entry Command

(CS = "L", RAS = "L", CAS = "L", WE = "H", CKE = "L", BA0, BA1, A0 to A12 = Don’t Care)

The Self Refresh command can be used to retain data, even if the rest of the system is powered

down. When in the Self Refresh mode, the DDR2 SDRAM retains data without external clocking. The

DDR2 SDRAM device has a built-in timer to accommodate Self Refresh operation. ODT must be

turned off before issuing Self Refresh command, by either driving ODT pin LOW or using an EMRS

command. Once the command is registered, CKE must be held LOW to keep the device in Self

Refresh mode. The DLL is automatically disabled upon entering Self Refresh and is automatically

enabled upon exiting Self Refresh. When the DDR2 SDRAM has entered Self Refresh mode, all of the

external signals except CKE, are ”Don’t Care”.

The clock is internally disabled during self refresh operation to save power. The user may change the

external clock frequency or halt the external clock one clock after Self Refresh entry is registered;

however, the clock must be restarted and stable before the device can exit self refresh operation.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 22 - Revision A01

7.3.8 Self Refresh Exit Command

(CKE = "H", CS = "H" or CKE = "H", CS = "L", RAS = "H", CAS = "H", WE = "H", BA0, BA1,

A0 to A12 = Don’t Care)

The procedure for exiting Self Refresh requires a sequence of commands. First, the clock must be

stable prior to CKE going back HIGH. Once Self Refresh Exit is registered, a delay of at least tXSNR

must be satisfied before a valid command can be issued to the device to allow for any internal refresh

in progress. CKE must remain HIGH for the entire Self Refresh exit period tXSRD for proper operation

except for self refresh re-entry.

Upon exit from Self Refresh, the DDR2 SDRAM can be put back into Self Refresh mode after waiting

at least tXSNR period and issuing one refresh command (refresh period of tRFC). NOP or Deselect

commands must be registered on each positive clock edge during the Self Refresh exit interval tXSNR.

ODT should be turned off during tXSRD.

The use of Self Refresh mode introduces the possibility that an internally timed refresh event can be

missed when CKE is raised for exit from Self Refresh mode. Upon exit from Self Refresh, the DDR2

SDRAM requires a minimum of one extra auto refresh command before it is put back into Self Refresh

mode.

7.3.9 Refresh Command

(CS = "L", RAS = "L", CAS = "L", WE = "H", CKE = "H", BA0, BA1, A0 to A12 = Don’t Care)

Refresh is used during normal operation of the DDR2 SDRAM. This command is non persistent, so it

must be issued each time a refresh is required.

The refresh addressing is generated by the internal refresh controller. This makes the address

bits ”Don’t Care” during an Auto Refresh command. The DDR2 SDRAM requires Auto Refresh cycles

at an average periodic interval of tREFI (max.).

When the refresh cycle has completed, all banks of the DDR2 SDRAM will be in the precharged (idle)

state. A delay between the auto refresh command (REF) and the next activate command or

subsequent auto refresh command must be greater than or equal to the auto refresh cycle time (tRFC).

To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the

absolute refresh interval is provided. A maximum of eight Refresh commands can be posted to any

given DDR2 SDRAM, meaning that the maximum absolute interval between any Refresh command

and the next Refresh command is 9 x tREFI.

T0 T1 T2 T3

CLK/CLK

CKE

CMD

≥ tRP ≥ tRFC ≥ tRFC

NOP NOP NOP ANY

REFREF

Precharge

"HIGH"

Tm Tn Tn + 1

Figure 13—Refresh command

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 23 - Revision A01

7.3.10 No-Operation Command

(CS = "L", RAS = "H", CAS = "H", WE = "H", CKE, BA0, BA1, A0 to A12 = Don’t Care)

The No-Operation command simply performs no operation (same command as Device Deselect).

7.3.11 Device Deselect Command

(CS = "H", RAS , CAS , WE , CKE, BA0, BA1, A0 to A12 = Don’t Care)

The Device Deselect command disables the command decoder so that the RAS ,CAS ,WE and

Address inputs are ignored. This command is similar to the No-Operation command.

7.4 Read and Write access modes

The DDR2 SDRAM provides a fast column access operation. A single Read or Write Command will

initiate a serial read or write operation on successive clock cycles. The boundary of the burst cycle is

strictly restricted to specific segments of the page length.

The 4 Mbit x 16 I/O x 4 Bank chip has a page length of 512 bits (defined by CA0 to CA8)*. The page

length of 512 is divided into 128 or 64 uniquely addressable boundary segments depending on burst

length, 128 for 4 bit burst, 64 for 8 bit burst respectively. A 4-bit or 8-bit burst operation will occur

entirely within one of the 128 or 64 groups beginning with the column address supplied to the device

during the Read or Write Command (CA0 to CA8). The second, third and fourth access will also occur

within this group segment. However, the burst order is a function of the starting address, and the burst

sequence.

A new burst access must not interrupt the previous 4 bit burst operation in case of BL = 4 setting.

However, in case of BL = 8 setting, two cases of interrupt by a new burst access are allowed, one

reads interrupted by a read, the other writes interrupted by a write with 4 bit burst boundary

respectively. The minimum CAS to CAS delay is defined by tCCD, and is a minimum of 2 clocks for

read or write cycles.

Note: Page length is a function of I/O organization and column addressing

4M bits × 16 organization (CA0 to CA8); Page Length = 512 bits

7.4.1 Posted

CAS

Posted CAS operation is supported to make command and data bus efficient for sustainable

bandwidths in DDR2 SDRAM. In this operation, the DDR2 SDRAM allows a CAS read or write

command to be issued immediately after the RAS bank activate command (or any time during the

RAS -CAS -delay time, tRCD, period). The command is held for the time of the Additive Latency (AL)

before it is issued inside the device. The Read Latency (RL) is controlled by the sum of AL and the

CAS Latency (CL). Therefore if a user chooses to issue a Read/Write command before the tRCDmin,

then AL (greater than 0) must be written into the EMR (1). The Write Latency (WL) is always defined

as RL -1 (Read Latency -1) where Read Latency is defined as the sum of Additive Latency plus CAS

Latency (RL = AL + CL). Read or Write operations using AL allow seamless bursts. (Example timing

waveforms refer to 10.11 and 10.12 seamless burst read/write operation diagram in Chapter 10)

7.4.1.1 Examples of posted CAS operation

Examples of a read followed by a write to the same bank where AL = 2 and where AL = 0 are shown

in Figures 14 and 15, respectively.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 24 - Revision A01

CMD

123 45 67891011120

-1

CLK /CLK

DQS/DQS

AL=2 CL=3

WL=RL-1=4

≥ tRCD

RL=AL+CL=5

Dout0 Din0

Active

A-Bank

Read

A-Bank

Write

A-Bank

Din1 Din2 Din3

Dout1 Dout2 Dout3

[AL = 2 and CL = 3, RL = (AL + CL) = 5, WL = (RL - 1) = 4, BL = 4]

Figure 14—Example 1: Read followed by a write to the same bank,

where AL = 2 and CL = 3, RL = (AL + CL) = 5, WL = (RL - 1) = 4, BL = 4

123456 7891011

0-1

CL=3

WL=RL-1=2

≥ tRCD

RL=AL+CL=3

AL=0

CMD

CLK/CLK

DQ Dout0 Dout1 Dout2 Dout3 Din0 Din1 Din2 Din3

Write

A-Bank

Read

A-Bank

Active

A-Bank

DQS/DQS

AL = 0 and CL = 3, RL = (AL + CL) = 3, WL = (RL - 1) = 2, BL = 4]

Figure 15—Example 2: Read followed by a write to the same bank,

where AL = 0 and CL = 3, RL = (AL + CL) = 3, WL = (RL - 1) = 2, BL = 4

7.4.2 Burst mode operation

Burst mode operation is used to provide a constant flow of data to memory locations (write cycle), or

from memory locations (read cycle). The parameters that define how the burst mode will operate are

burst sequence and burst length. The DDR2 SDRAM supports 4 bit and 8 bit burst modes only. For 8

bit burst mode, full interleave address ordering is supported, however, sequential address ordering is

nibble based for ease of implementation. The burst length is programmable and defined by MR A[2:0].

The burst type, either sequential or interleaved, is programmable and defined by MR [A3]. Seamless

burst read or write operations are supported.

Unlike DDR1 devices, interruption of a burst read or writes cycle during BL = 4 mode operation is

prohibited. However in case of BL = 8 mode, interruption of a burst read or write operation is limited to

two cases, reads interrupted by a read, or writes interrupted by a write. (Example timing waveforms

refer to 10.13 and 10.14 Burst read and write interrupt timing diagram in Chapter 10)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 25 - Revision A01

Therefore the Burst Stop command is not supported on DDR2 SDRAM devices.

Table 3—Burst Length and Sequence

Burst Length Starting Address

(A2 A1 A0)

Sequential Addressing

(decimal)

Interleave Addressing

(decimal)

x00 0, 1, 2, 3 0, 1, 2, 3

x01 1, 2, 3, 0 1, 0, 3, 2

x10 2, 3, 0, 1 2, 3, 0, 1

x11 3, 0, 1, 2 3, 2, 1, 0

000 0, 1, 2, 3, 4, 5, 6, 7 0, 1, 2, 3, 4, 5, 6, 7

001 1, 2, 3, 0, 5, 6, 7, 4 1, 0, 3, 2, 5, 4, 7, 6

010 2, 3, 0, 1, 6, 7, 4, 5 2, 3, 0, 1, 6, 7, 4, 5

011 3, 0, 1, 2, 7, 4, 5, 6 3, 2, 1, 0, 7, 6, 5, 4

100 4, 5, 6, 7, 0, 1, 2, 3 4, 5, 6, 7, 0, 1, 2, 3

101 5, 6, 7, 4, 1, 2, 3, 0 5, 4, 7, 6, 1, 0, 3, 2

110 6, 7, 4, 5, 2, 3, 0, 1 6, 7, 4, 5, 2, 3, 0, 1

111 7, 4, 5, 6, 3, 0, 1, 2 7, 6, 5, 4, 3, 2, 1, 0

7.4.3 Burst read mode operation

Burst Read is initiated with a READ command. The address inputs determine the starting column

address for the burst. The delay from the start of the command to when the data from the first cell

appears on the outputs is equal to the value of the read latency (RL). The data strobe output (DQS) is

driven LOW one clock cycle before valid data (DQ) is driven onto the data bus. The first bit of the burst

is synchronized with the rising edge of the data strobe (DQS). Each subsequent data-out appears on

the DQ pin in phase with the DQS signal in a source synchronous manner. The RL is equal to an

additive latency (AL) plus CAS Latency (CL). The CL is defined by the Mode Register Set (MRS). The

AL is defined by the Extended Mode Register EMR (1). (Example timing waveforms refer to 10.7 and

10.8 Data output (read) timing and Burst read operation diagram in Chapter 10)

7.4.4 Burst write mode operation

Burst Write is initiated with a WRITE command. The address inputs determine the starting column

address for the burst. Write Latency (WL) is defined by a Read Latency (RL) minus one and is equal

to (AL + CL -1); and is the number of clocks of delay that are required from the time the write

command is registered to the clock edge associated to the first DQS strobe. A data strobe signal

(DQS) should be driven LOW (preamble) nominally half clock prior to the WL. The first data bit of the

burst cycle must be applied to the DQ pins at the first rising edge of the DQS following the preamble.

The tDQSS specification must be satisfied for each positive DQS transition to its associated clock edge

during write cycles. The subsequent burst bit data are issued on successive edges of the DQS until

the burst length is completed, which is 4 or 8 bit burst. When the burst has finished, any additional

data supplied to the DQ pins will be ignored. The DQ Signal is ignored after the burst write operation is

complete. The time from the completion of the burst write to bank precharge is the write recovery time

(WR). (Example timing waveforms refer to 10.9 and 10.10 Data input (write) timing and Burst write

operation diagram in Chapter 10)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 26 - Revision A01

7.4.5 Write data mask

One write data mask (DM) pin for each 8 data bits (DQ) will be supported on DDR2 SDRAM,

consistent with the implementation on DDR1 SDRAM. It has identical timings on write operations as

the data bits, and though used in a unidirectional manner, is internally loaded identically to data bits to

insure matched system timing. DM is not used during read cycles. (Example timing waveform refer to

10.15 Write operation with Data Mask diagram in Chapter 10)

7.5 Burst Interrupt

Read or Write burst interruption is prohibited for burst length of 4 and only allowed for burst length of 8

under the following conditions:

1. Read burst of 8 can only be interrupted by another Read command. Read burst interruption by

Write or Precharge Command is prohibited.

2. Write burst of 8 can only be interrupted by another Write command. Write burst interruption by

Read or Precharge Command is prohibited.

3. Read burst interrupt must occur exactly two clocks after the previous Read command. Any other

Read burst interrupt timings are prohibited.

4. Write burst interrupt must occur exactly two clocks after the previous Write command. Any other

Write burst interrupt timings are prohibited.

5. Read or Write burst interruption is allowed to any bank inside the DDR2 SDRAM.

6. Read or Write burst with Auto-precharge enabled is not allowed to interrupt.

7. Read burst interruption is allowed by a Read with Auto-precharge command.

8. Write burst interruption is allowed by a Write with Auto-precharge command.

9. All command timings are referenced to burst length set in the mode register. They are not

referenced to the actual burst. For example below:

z Minimum Read to Precharge timing is AL + BL/2 where BL is the burst length set in the

mode register and not the actual burst (which is shorter because of interrupt).

z Minimum Write to Precharge timing is WL + BL/ 2 + tWR, where tWR starts with the rising

clock after the un-interrupted burst end and not from the end of the actual burst end.

(Example timing waveforms refer to 10.13 and 10.14 Burst read and write interrupt timing diagram in

Chapter 10)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 27 - Revision A01

7.6 Precharge operation

The Precharge Command is used to precharge or close a bank that has been activated. The

Precharge Command can be used to precharge each bank independently or all banks simultaneously.

Three address bits A10, BA0 and BA1 are used to define which bank to precharge when the

command is issued.

Table 4—Bank selection for precharge by address bits

A10 BA1 BA0 Precharge Bank(s)

LOW LOW LOW Bank 0 only

LOW LOW HIGH Bank 1 only

LOW HIGH LOW Bank 2 only

LOW HIGH HIGH Bank 3 only

HIGH Don’t Care Don’t Care All Banks

7.6.1 Burst read operation followed by precharge

Minimum Read to Precharge command spacing to the same bank = AL + BL/2 + max(RTP, 2) - 2 clks

For the earliest possible precharge, the precharge command may be issued on the rising edge which

is “Additive Latency (AL) + BL/2 + max(RTP, 2) - 2 clocks” after a Read command. A new bank active

(command) may be issued to the same bank after the RAS precharge time (tRP). A precharge

command cannot be issued until tRAS is satisfied.

The minimum Read to Precharge spacing has also to satisfy a minimum analog time from the rising

clock edge that initiates the last 4-bit prefetch of a Read to Precharge command. This time is called

tRTP (Read to Precharge). For BL = 4 this is the time from the actual read (AL after the Read

command) to Precharge command. For BL = 8 this is the time from AL + 2 clocks after the Read to the

Precharge command. (Example timing waveforms refer to 10.16 to 10.20 Burst read operation

followed by precharge diagram in Chapter 10)

7.6.2 Burst write operation followed by precharge

Minimum Write to Precharge Command spacing to the same bank = WL + BL/2 clks + tWR

For write cycles, a delay must be satisfied from the completion of the last burst write cycle until the

Precharge Command can be issued. This delay is known as a write recovery time (tWR) referenced

from the completion of the burst write to the precharge command. No Precharge command should be

issued prior to the tWR delay. (Example timing waveforms refer to 10.21 to 10.22 Burst write operation

followed by precharge diagram in Chapter 10)

7.7 Auto-precharge operation

Before a new row in an active bank can be opened, the active bank must be precharged using either

the Precharge command or the Auto-precharge function. When a Read or a Write command is given

to the DDR2 SDRAM, the CAS timing accepts one extra address, column address A10, to allow the

active bank to automatically begin precharge at the earliest possible moment during the burst read or

write cycle. If A10 is LOW when the READ or WRITE command is issued, then normal Read or Write

burst operation is executed and the bank remains active at the completion of the burst sequence. If

A10 is HIGH when the Read or Write command is issued, then the Auto-precharge function is

engaged. During Auto-precharge, a Read command will execute as normal with the exception that the

active bank will begin to precharge on the rising edge which is CAS Latency (CL) clock cycles before

the end of the read burst.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 28 - Revision A01

Auto-precharge is also implemented during Write commands. The precharge operation engaged by

the Auto-precharge command will not begin until the last data of the burst write sequence is properly

stored in the memory array.

This feature allows the precharge operation to be partially or completely hidden during burst read

cycles (dependent upon CAS Latency) thus improving system performance for random data access.

The RAS lockout circuit internally delays the Precharge operation until the array restore operation

has been completed (tRAS satisfied) so that the Auto-precharge command may be issued with any

read or write command.

7.7.1 Burst read with Auto-precharge

If A10 is HIGH when a Read Command is issued, the Read with Auto-precharge function is engaged.

The DDR2 SDRAM starts an Auto-precharge operation on the rising edge which is (AL + BL/2) cycles

later from the Read with AP command if tRAS(min) and tRTP(min) are satisfied. (Example timing

waveform refer to 10.23 Burst read operation with Auto-precharge diagram in Chapter 10)

If tRAS(min) is not satisfied at the edge, the start point of Auto-precharge operation will be delayed until

tRAS(min) is satisfied.

If tRTP(min) is not satisfied at the edge, the start point of Auto-precharge operation will be delayed until

tRTP(min) is satisfied.

In case the internal precharge is pushed out by tRTP, tRP starts at the point where tRTP ends (not at the

next rising clock edge after this event). So for BL = 4 the minimum time from Read with Auto-

precharge to the next Activate command becomes AL + RU{ (tRTP + tRP) / tCK(avg) } (Example timing

waveform refer to 10.24 Burst read operation with Auto-precharge diagram in Chapter 10.), for BL = 8

the time from Read with Auto-precharge to the next Activate command is AL + 2 + RU{ (tRTP + tRP) /

tCK(avg) }, where RU stands for “rounded up to the next integer”. In any event internal precharge does

not start earlier than two clocks after the last 4-bit prefetch.

A new bank active command may be issued to the same bank if the following two conditions are

satisfied simultaneously.

z The RAS precharge time (tRP) has been satisfied from the clock at which the Auto-precharge

begins.

z The RAS cycle time (tRC) from the previous bank activation has been satisfied.

(Example timing waveforms refer to 10.25 to 10.26 Burst read with Auto-precharge followed by an

activation to the same bank (tRC Limit) and (tRP Limit) diagram in Chapter 10)

7.7.2 Burst write with Auto-precharge

If A10 is HIGH when a Write Command is issued, the Write with Auto-Precharge function is engaged.

The DDR2 SDRAM automatically begins precharge operation after the completion of the burst write

plus write recovery time (WR) programmed in the mode register. The bank undergoing Auto-

precharge from the completion of the write burst may be reactivated if the following two conditions are

satisfied.

z The data-in to bank activate delay time (WR + tRP) has been satisfied.

z The RAS cycle time (tRC) from the previous bank activation has been satisfied.

(Example timing waveforms refer to 10.27 to 10.28 Burst write with Auto-precharge (tRC Limit) and

(WR + tRP Limit) diagram in Chapter 10)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 29 - Revision A01

Table 5—Precharge & Auto-precharge clarifications

From

Command

To Command Minimum Delay between “From

Command” to “To Command”

Unit Notes

Precharge (to same Bank as Read) AL + BL/2 + max(RTP, 2) - 2 clks 1, 2 Read

Precharge All AL + BL/2 + max(RTP, 2) - 2 clks 1, 2

Precharge (to same Bank as Read w/AP) AL + BL/2 + max(RTP, 2) - 2 clks 1, 2 Read w/AP

Precharge All AL + BL/2 + max(RTP, 2) - 2 clks 1, 2

Precharge (to same Bank as Write) WL + BL/2 + tWR clks 2 Write

Precharge All WL + BL/2 + tWR clks 2

Precharge (to same Bank as Write w/AP) WL + BL/2 + WR clks 2 Write w/AP

Precharge All WL + BL/2 + WR clks 2

Precharge (to same Bank as Precharge) 1 clks 2 Precharge

Precharge All 1 clks 2

Precharge 1 clks 2 Precharge

All Precharge All 1 clks 2

Notes:

1. RTP[cycles] = RU{ tRTP[nS] / tCK(avg)[nS] }, where RU stands for round up.

2. For a given bank, the precharge period should be counted from the latest precharge command, either one bank precharge or

precharge all, issued to that bank. The precharge period is satisfied after tRP depending on the latest precharge command

issued to that bank.

7.8 Refresh Operation

Two types of Refresh operation can be performed on the device: Auto Refresh and Self Refresh. By

repeating the Auto Refresh cycle, each bank in turn refreshed automatically. The Refresh operation

must be performed 8192 times (rows) within 64mS. The period between the Auto Refresh command

and the next command is specified by tRFC.

Self Refresh mode enters issuing the Self Refresh command (CKE asserted "LOW") while all banks

are in the idle state. The device is in Self Refresh mode for as long as CKE held "LOW". In the case

of 8192 burst Auto Refresh commands, 8192 burst Auto Refresh commands must be performed within

7.8 µS before entering and after exiting the Self Refresh mode. In the case of distributed Auto Refresh

commands, distributed auto refresh commands must be issued every 7.8 µS and the last distributed

Auto Refresh commands must be performed within 7.8 µS before entering the self refresh mode. After

exiting from the Self Refresh mode, the refresh operation must be performed within 7.8 µS. In Self

Refresh mode, all input/output buffers are disable, resulting in lower power dissipation (except CKE

buffer). (Example timing waveform refer to 10.29 Self Refresh diagram in Chapter 10)

7.9 Power Down Mode

Power-down is synchronously entered when CKE is registered LOW, along with NOP or Deselect

command. CKE is not allowed to go LOW while mode register or extended mode register command

time, or read or write operation is in progress. CKE is allowed to go LOW while any other operation

such as row activation, Precharge or Auto-precharge or Auto Refresh is in progress, but power down

IDD specification will not be applied until finishing those operations.

The DLL should be in a locked state when power-down is entered. Otherwise DLL should be reset

after exiting power-down mode for proper read operation.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 30 - Revision A01

7.9.1 Power Down Entry

Two types of Power Down Mode can be performed on the device: Precharge Power Down Mode and

Active Power Down Mode.

If power down occurs when all banks are idle, this mode is referred to as Precharge Power Down; if

power down occurs when there is a row active in any bank, this mode is referred to as Active Power

Down. Entering power down deactivates the input and output buffers, excluding CLK, CLK , ODT and

CKE. Also the DLL is disabled upon entering Precharge Power Down or slow exit Active Power Down,

but the DLL is kept enabled during fast exit Active Power Down.

In power down mode, CKE LOW and a stable clock signal must be maintained at the inputs of the

DDR2 SDRAM, and ODT should be in a valid state but all other input signals are “Don’t Care”. CKE

LOW must be maintained until tCKE has been satisfied. Maximum power down duration is limited by

the refresh requirements of the device, which allows a maximum of 9 x tREFI if maximum posting of

REF is utilized immediately before entering power down. (Example timing waveforms refer to 10.30 to

10.31 Active and Precharged Power Down Mode Entry and Exit diagram in Chapter 10)

7.9.2 Power Down Exit

The power-down state is synchronously exited when CKE is registered HIGH (along with a NOP or

Deselect command). CKE high must be maintained until tCKE has been satisfied. A valid, executable

command can be applied with power-down exit latency, tXP, tXARD, or tXARDS, after CKE goes HIGH.

Power-down exit latency is defined at AC Characteristics table of this data sheet.

7.10 Input clock frequency change during precharge power down

DDR2 SDRAM input clock frequency can be changed under following condition:

DDR2 SDRAM is in precharged power down mode. ODT must be turned off and CKE must be at logic

LOW level. A minimum of 2 clocks must be waited after CKE goes LOW before clock frequency may

change. SDRAM input clock frequency is allowed to change only within minimum and maximum

operating frequency specified for the particular speed grade. During input clock frequency change,

ODT and CKE must be held at stable LOW levels.

Once input clock frequency is changed, stable new clocks must be provided to DRAM before

precharge power down may be exited and DLL must be RESET via MRS command after precharge

power down exit. Depending on new clock frequency an additional MRS or EMRS command may

need to be issued to appropriately set the WR, CL etc…

During DLL re-lock period, ODT must remain off. After the DLL lock time, the DRAM is ready to

operate with new clock frequency. (Example timing waveform refer to 10.32 Clock frequency change

in precharge Power Down mode diagram in Chapter 10)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 31 - Revision A01

8. OPERATION MODE

8.1 Command Truth Table

CKE

COMMAND Previous

Cycle

Current

Cycle

BA1

BA0

A12

A11 A10 A9-A0 CS RAS CAS WE NOTES

Bank Activate H H BA Row Address L L H H 1, 2

Single Bank

Precharge H H BA X L X L L H L 1, 2

Precharge All

Banks H H X X H X L L H L 1

Write H H BA Column L Column L H L L 1, 2, 3

Write with

Auto-precharge H H BA Column H Column L H L L 1, 2, 3

Read H H BA Column L Column L H L H 1, 2, 3

Read with

Auto-precharge H H BA Column H Column L H L H 1, 2, 3

(Extended)

Mode Register

Set

H H BA OP Code L L L L 1, 2

No Operation H X X X X X L H H H 1

Device

Deselect H X X X X X H X X X 1

Refresh H H X X X X L L L H 1

Self Refresh

Entry H L X X X X L L L H 1, 4

H X X X

Self Refresh

Exit L H X X X X L H H H

1, 4, 5

H X X X

Power Down

Mode Entry H L X X X X L H H H

1, 6

H X X X

Power Down

Mode Exit L H X X X X

L H H H

1, 6

Notes:

1. All DDR2 SDRAM commands are defined by states of CS , RAS , CAS , WE and CKE at the rising edge of the clock.

2. Bank addresses BA[1:0] determine which bank is to be operated upon. For (E)MRS BA selects an (Extended) Mode Register.

3. Burst reads or writes at BL = 4 can not be terminated or interrupted. See Burst Interrupt in section 7.5 for details.

4. VREF must be maintained during Self Refresh operation.

5. Self Refresh Exit is asynchronous.

6. The Power Down does not perform any refresh operations. The duration of Power Down Mode is therefore limited by the

refresh requirements outlined in section 7.9.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 32 - Revision A01

8.2 Clock Enable (CKE) Truth Table for Synchronous Transitions

CKE

CURRENT

STATE2 Previous Cycle 1

(N-1)

Current Cycle 1

(N)

COMMAND (N) 3

RAS ,CAS , WE , CS

ACTION (N) 3 NOTES

L L X Maintain Power Down 11, 13, 15

Power Down

L H DESELECT or NOP Power Down Exit 4, 8, 11, 13

L L X Maintain Power Down 11, 15, 16

Self Refresh

L H DESELECT or NOP Self Refresh Exit 4, 5, 9, 16

Bank(s) Active H L DESELECT or NOP Active Power Down

Entry

4, 8, 10, 11,

H L DESELECT or NOP

Precharge Power Down

Entry

4, 8, 10, 11,

All Banks Idle

H L REFRESH Self Refresh Entry 6, 9, 11, 13

H H Refer to the Command Truth Table 7

Notes:

1. CKE (N) is the logic state of CKE at clock edge N; CKE (N–1) was the state of CKE at the previous clock edge.

2. Current state is the state of the DDR2 SDRAM immediately prior to clock edge N.

3. COMMAND (N) is the command registered at clock edge N, and ACTION (N) is a result of COMMAND (N).

4. All states and sequences not shown are illegal or reserved unless explicitly described elsewhere in this document.

5. On Self Refresh Exit DESELECT or NOP commands must be issued on every clock edge occurring during the tXSNR period.

Read commands may be issued only after tXSRD (200 clocks) is satisfied.

6. Self Refresh mode can only be entered from the All Banks Idle state.

7. Must be a legal command as defined in the Command Truth Table.

8. Valid commands for Power Down Entry and Exit are NOP and DESELECT only.

9. Valid commands for Self Refresh Exit are NOP and DESELECT only.

10. Power Down and Self Refresh can not be entered while Read or Write operations, (Extended) Mode Register Set

operations or Precharge operations are in progress. See section 7.9 "Power Down Mode" and section 7.3.7/7.3.8 "Self

Refresh Entry/Exit Command" for a detailed list of restrictions.

11. tCKEmin of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the

valid input level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not

transition from its valid level during the time period of tIS + 2 x tCK + tIH.

12. The state of ODT does not affect the states described in this table. The ODT function is not available during Self Refresh.

See section 7.2.4.

13. The Power Down does not perform any refresh operations. The duration of Power Down Mode is therefore limited by the

refresh requirements outlined in section 7.9.

14. CKE must be maintained HIGH while the SDRAM is in OCD calibration mode.

15. ”X” means “don’t care (including floating around VREF)” in Self Refresh and Power Down. However ODT must be driven

high or low in Power Down if the ODT function is enabled (Bit A2 or A6 set to “1” in EMR (1)).

16. VREF must be maintained during Self Refresh operation.

8.3 Data Mask (DM) Truth Table

FUNCTION DM DQS NOTE

Write enable L Valid 1

Write inhibit H X 1

Note:

1. Used to mask write data, provided coincident with the corresponding data.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 33 - Revision A01

8.4 Function Truth Table

CURRENT

STATE CS RAS

CAS

ADDRESS COMMAND ACTION NOTES

H X X X X DSL NOP or Power down

L H H H X NOP NOP or Power down

L H L H BA, CA, A10 READ/READA ILLEGAL 1

L H L L BA, CA, A10 WRIT/WRITA ILLEGAL 1

L L H H BA, RA ACT Row activating

L L H L BA, A10 PRE/PREA Precharge/ Precharge all banks

L L L H X AREF/SELF Auto Refresh or Self Refresh 2

Idle

L L L L Op-Code MRS/EMRS Mode/Extended register

accessing 2

H X X X X DSL NOP

L H H H X NOP NOP

L H L H BA, CA, A10 READ/READA Begin read

L H L L BA, CA, A10 WRIT/WRITA Begin write

L L H H BA, RA ACT ILLEGAL 1

L L H L BA, A10 PRE/PREA Precharge/ Precharge all banks

L L L H X AREF/SELF ILLEGAL

Banks

Active

L L L L Op-Code MRS/EMRS ILLEGAL

H X X X X DSL Continue burst to end

L H H H X NOP Continue burst to end

L H L H BA, CA, A10 READ/READA Burst interrupt 1, 3

L H L L BA, CA, A10 WRIT/WRITA ILLEGAL 1

L L H H BA, RA ACT ILLEGAL 1

L L H L BA, A10 PRE/PREA ILLEGAL 1

L L L H X AREF/SELF ILLEGAL

Read

L L L L Op-Code MRS/EMRS ILLEGAL

H X X X X DSL Continue burst to end

L H H H X NOP Continue burst to end

L H L H BA, CA, A10 READ/READA ILLEGAL 1

L H L L BA, CA, A10 WRIT/WRITA Burst interrupt 1, 3

L L H H BA, RA ACT ILLEGAL 1

L L H L BA, A10 PRE/PREA ILLEGAL 1

L L L H X AREF/SELF ILLEGAL

Write

L L L L Op-Code MRS/EMRS ILLEGAL

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 34 - Revision A01

Function Truth Table, continued

CURRENT

STATE CS RAS

CAS

ADDRESS COMMAND ACTION NOTES

H X X X X DSL Continue burst to end

L H H H X NOP Continue burst to end

L H L H

BA, CA, A10 READ/READA ILLEGAL 1

L H L L

BA, CA, A10 WRIT/WRITA ILLEGAL 1

L L H H

BA, RA ACT ILLEGAL 1

L L H L

BA, A10 PRE/PREA ILLEGAL 1

L L L H X AREF/SELF ILLEGAL

Read with

Auto-

precharge

L L L L

Op-Code MRS/EMRS ILLEGAL

H X X X X DSL Continue burst to end

L H H H X NOP Continue burst to end

L H L H

BA, CA, A10 READ/READA ILLEGAL 1

L H L L

BA, CA, A10 WRIT/WRITA ILLEGAL 1

L L H H

BA, RA ACT ILLEGAL 1

L L H L

BA, A10 PRE/PREA ILLEGAL 1

L L L H X AREF/SELF ILLEGAL

Write with

Auto-

precharge

L L L L

Op-Code MRS/EMRS ILLEGAL

H X X X X DSL NOP-> Idle after tRP

L H H H X NOP NOP-> Idle after tRP

L H L H

BA, CA, A10 READ/READA ILLEGAL 1

L H L L

BA, CA, A10 WRIT/WRITA ILLEGAL 1

L L H H

BA, RA ACT ILLEGAL 1

L L H L

BA, A10 PRE/PREA NOP-> Idle after tRP 1

L L L H X AREF/SELF ILLEGAL

Precharge

L L L L

Op-Code MRS/EMRS ILLEGAL

H X X X X DSL NOP-> Row active after tRCD

L H H H X NOP NOP-> Row active after tRCD

L H L H

BA, CA, A10 READ/READA ILLEGAL 1

L H L L

BA, CA, A10 WRIT/WRITA ILLEGAL 1

L L H H

BA, RA ACT ILLEGAL 1

L L H L

BA, A10 PRE/PREA ILLEGAL 1

L L L H X AREF/SELF ILLEGAL

Row

Activating

L L L L

Op-Code MRS/EMRS ILLEGAL

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 35 - Revision A01

Function Truth Table, continued

CURRENT

STATE CS RAS

CAS

ADDRESS COMMAND ACTION NOTES

H X X X X DSL NOP-> Bank active after tWR

L H H H X NOP NOP-> Bank active after tWR

L H L H

BA, CA, A10 READ/READA ILLEGAL 1

L H L L

BA, CA, A10 WRIT/WRITA New write

L L H H

BA, RA ACT ILLEGAL 1

L L H L

BA, A10 PRE/PREA ILLEGAL 1

L L L H X AREF/SELF ILLEGAL

Write

Recovering

L L L L

Op-Code MRS/EMRS ILLEGAL

H X X X X DSL NOP-> Precharge after tWR

L H H H X NOP NOP-> Precharge after tWR

L H L H

BA, CA, A10 READ/READA ILLEGAL 1

L H L L

BA, CA, A10 WRIT/WRITA ILLEGAL 1

L L H H

BA, RA ACT ILLEGAL 1

L L H L

BA, A10 PRE/PREA ILLEGAL 1

L L L H X AREF/SELF ILLEGAL

Write

Recovering

with Auto-

precharge

L L L L

Op-Code MRS/EMRS ILLEGAL

H X X X X DSL NOP-> Idle after tRC

L H H H X NOP NOP-> Idle after tRC

L H L H

BA, CA, A10 READ/READA ILLEGAL

L H L L

BA, CA, A10 WRIT/WRITA ILLEGAL

L L H H BA, RA ACT ILLEGAL

L L H L BA, A10 PRE/PREA ILLEGAL

L L L H X AREF/SELF ILLEGAL

Refreshing

L L L L Op-Code MRS/EMRS ILLEGAL

H X X X X DSL NOP-> Idle after tMRD

L H H H X NOP NOP-> Idle after tMRD

L H L H BA, CA, A10 READ/READA ILLEGAL

L H L L BA, CA, A10 WRIT/WRITA ILLEGAL

L L H H BA, RA ACT ILLEGAL

L L H L BA, A10 PRE/PREA ILLEGAL

L L L H X AREF/SELF ILLEGAL

Mode

Accessing

L L L L Op-Code MRS/EMRS ILLEGAL

Notes:

1. This command may be issued for other banks, depending on the state of the banks.

2. All banks must be in "IDLE".

3. Read or Write burst interruption is prohibited for burst length of 4 and only allowed for burst length of 8. Burst read/write can

only be interrupted by another read/write with 4 bit burst boundary. Any other case of read/write interrupt is not allowed.

Remark: H = High level, L = Low level, X = High or Low level (Don’t Care), V = Valid data.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 36 - Revision A01

8.5 Simplified Stated Diagram

OCD

calibration

Initialization

Sequence

Self Refreshing

Refreshing

Precharge

Power

Down

Activating

Idle

All banks

Precharged

Setting

MR,EMR (1)

EMR (2)

EMR (3)

Active

Power

Down

Bank

Active

ReadingWriting

Writing

with

Auto-precharge

Precharging

Reading

with

Auto-precharge

(E)MRS REF

SELF

CKEH

CKEL

CKEH

ACT

PRE, PREA

Read

CKEL

CKEH

CKEL

Write

WRITA

WRITA READA

Write

READA

CKEL

Autoomatic Sequence

Command Sequence

Read

CKEL

PRE

CKEL

Write Read

CKEL

PRE, PREAPRE, PREA

WRITA

CKEL = CKE LOW, enter Power Down

CKEH = CKE HIGH, exit Power Down

CKEH = CKE HIGH, exit Self Refresh

ACT = Activate

WRITA = Write with Auto-precharge

READA = Read (with Auto-precharge

PREA = Precharge All

(E)MRS = (Extended) Mode Register Set

SELF = Enter Self Refresh

REF = Refresh

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 37 - Revision A01

9. ELECTRICAL CHARACTERISTICS

9.1 Absolute Maximum Ratings

PARAMETER SYMBOL RATING UNIT NOTES

Voltage on VDD pin relative to VSS VDD -1.0 ~ 2.3 V 1, 2

Voltage on VDDQ pin relative to VSS VDDQ -0.5 ~ 2.3 V 1, 2

Voltage on VDDL pin relative to VSS VDDL -0.5 ~ 2.3 V 1, 2

Voltage on any pin relative to VSS VIN, VOUT -0.5 ~ 2.3 V 1, 2

Storage Temperature TSTG -55 ~ 100 °C 1, 2, 3

Notes:

1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a

stress rating only and functional operation of the device at these or any other conditions above those indicated in the

operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended

periods may affect reliability.

2. When VDD and VDDQ and VDDL are less than 500mV; VREF may be equal to or less than 300mV.

3. Storage temperature is the case surface temperature on the center/top side of the DRAM.

9.2 Operating Temperature Condition

PARAMETER SYMBOL RATING UNIT NOTES

Operating Temperature (for -18/-25/-3) TOPR 0 ~ 85 °C 1, 2, 3

Operating Temperature (for 25I/25A) TOPR -40 ~ 95 °C 1, 2, 3, 4

Notes:

1. Operating Temperature is the case surface temperature on the center/top side of the DRAM.

2. Supporting 0 ~ 85°C with full JEDEC AC and DC specifications.

3. Supporting 0 ~ 85 °C and being able to extend to 95 °C with doubling Auto Refresh commands in frequency to a 32 mS

period ( tREFI = 3.9 µS) and to enter to Self Refresh mode at this high temperature range via A7 "1" on EMR (2).

4. During operation, the DRAM case temperature must be maintained between -40 to 95°C for Industrial and Automotive parts

under all specification parameters.

9.3 Recommended DC Operating Conditions

(0℃ ≤ TCASE ≤ 85℃ for -18/-25/-3, -40℃ ≤ TCASE ≤ 95℃ for 25I/25A, VDD, VDDQ = 1.8V ± 0.1V)

SYM. PARAMETER MIN. TYP. MAX. UNIT NOTES

VDD Supply Voltage 1.7 1.8 1.9 V 1

VDDL Supply Voltage for DLL 1.7 1.8 1.9 V 5

VDDQ Supply Voltage for Output 1.7 1.8 1.9 V 1, 5

VREF Input Reference Voltage 0.49 x VDDQ 0.5 x VDDQ 0.51 x VDDQ V 2, 3

VTT Termination Voltage (System) VREF - 0.04 VREF VREF + 0.04 V 4

Notes:

1. There is no specific device VDD supply voltage requirement for SSTL_18 compliance. However under all conditions VDDQ

must than or equal to VDD.

2. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically the value of VREF

is expected to be about 0.5 x VDDQ of the transmitting device and VREF is expected to track variations in VDDQ.

3. Peak to peak AC noise on VREF may not exceed +/-2 % VREF(dc).

4. VTT of transmitting device must track VREF of receiving device.

5. VDDQ tracks with VDD, VDDL tracks with VDD. AC parameters are measured with VDD, VDDQ and VDDDL tied together.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 38 - Revision A01

9.4 ODT DC Electrical Characteristics

(0℃ ≤ TCASE ≤ 85℃ for -18/-25/-3, -40℃ ≤ TCASE ≤ 95℃ for 25I/25A, VDD, VDDQ = 1.8V ± 0.1V)

PARAMETER/CONDITION SYM. MIN. NOM. MAX. UNIT NOTES

Rtt effective impedance value for EMRS(A6,A2)=0,1; 75 Ω Rtt1(eff) 60 75 90 Ω 1

Rtt effective impedance value for EMRS(A6,A2)=1,0; 150 ΩRtt2(eff) 120 150 180 Ω 1

Rtt effective impedance value for EMRS(A6,A2)=1,1; 50 Ω Rtt3(eff) 40 50 60 Ω 1, 2

Deviation of VM with respect to VDDQ/2 ΔVM -6 +6 % 1

Notes:

1. Test condition for Rtt measurements.

2. Optional for DDR2-667, mandatory for DDR2-800 and DDR2-1066.

Measurement Definition for Rtt(eff):

Apply VIH (ac) and VIL (ac) to test pin separately, then measure current I(VIH (ac)) and I(VIL (ac))

respectively. VIH (ac), VIL (ac), and VDDQ values defined in SSTL_18.

Rtt(eff) = (VIH(ac) – VIL(ac)) /(I(VIHac) – I(VILac))

Measurement Definition for ΔVM:

Measure voltage (VM) at test pin (midpoint) with no load.

ΔVM = ((2 x Vm / VDDQ) – 1) x 100%

9.5 Input DC Logic Level

(0℃ ≤ TCASE ≤ 85℃ for -18/-25/-3, -40℃ ≤ TCASE ≤ 95℃ for 25I/25A, VDD, VDDQ = 1.8V ± 0.1V)

PARAMETER SYM. MIN. MAX. UNIT

DC input logic HIGH VIH(dc) VREF + 0.125 VDDQ + 0.3 V

DC input logic LOW VIL(dc) -0.3 VREF - 0.125 V

9.6 Input AC Logic Level

(0℃ ≤ TCASE ≤ 85℃ for -18/-25/-3, -40℃ ≤ TCASE ≤ 95℃ for 25I/25A, VDD, VDDQ = 1.8V ± 0.1V)

-18 -25/25I/25A/-3

PARAMETER SYM. MIN. MAX. MIN. MAX.

UNIT

AC input logic HIGH VIH (ac) VREF + 0.200 − VREF + 0.200 VDDQ + VPEAK1V

AC input logic LOW VIL (ac) − VREF - 0.200 VSSQ - VPEAK1VREF - 0.200 V

Note:

1. Refer to the page 66 sections 9.14.1 and 9.14.2 AC Overshoot/Undershoot specification table for VPEAK value: maximum

peak amplitude allowed for Overshoot/Undershoot.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 39 - Revision A01

9.7 Capacitance

SYM. PARAMETER MIN. MAX. UNIT

CCK Input Capacitance , CLK and CLK 1.0 2.0 pF

CDCK Input Capacitance delta , CLK and CLK − 0.25 pF

CI input Capacitance, all other input-only pins 1.0 1.75 pF

CDI Input Capacitance delta, all other input-only pins − 0.25 pF

CIO Input/output Capacitance, DQ, LDM, UDM, LDQS,

LDQS , UDQS, UDQS 2.5 3.5 pF

CDIO Input/output Capacitance delta, DQ, LDM, UDM,

LDQS, LDQS , UDQS, UDQS − 0.5 pF

9.8 Leakage and Output Buffer Characteristics

SYM. PARAMETER MIN. MAX. UNIT NOTES

IIL Input Leakage Current

(0V≦VIN≦VDD) -2 2 µA 1

IOL Output Leakage Current

(Output disabled, 0V≦VOUT≦VDDQ) -5 5 µA 2

VOH Minimum Required Output Pull-up VTT + 0.603 − V

VOL Maximum Required Output Pull-down − VTT - 0.603 V

IOH(dc) Output Minimum Source DC Current -13.4 − mA 3, 5

IOL(dc) Output Minimum Sink DC Current 13.4 − mA 4, 5

Notes:

1. All other pins not under test = 0 V.

2. DQ, LDQS, LDQS , UDQS, UDQS are disabled and ODT is turned off.

3. VDDQ = 1.7 V; VOUT = 1.42 V. (VOUT - VDDQ)/IOH must be less than 21 Ω for values of VOUT between VDDQ and VDDQ -

0.28V.

4. VDDQ = 1.7 V; VOUT = 0.28V. VOUT/IOL must be less than 21 Ω for values of VOUT between 0 V and 0.28V.

5. The values of IOH(dc) and IOL(dc) are based on the conditions given in Notes 3 and 4. They are used to test drive current

capability to ensure VIHmin plus a noise margin and VILmax minus a noise margin are delivered to an SSTL_18 receiver.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 40 - Revision A01

9.9 DC Characteristics

(0℃ ≤ TCASE ≤ 85℃ for -18/-25/-3, -40℃ ≤ TCASE ≤ 95℃ for 25I/25A, VDD, VDDQ = 1.8V ± 0.1V)

-18

-25

25I

25A

-3

SYM. CONDITIONS

MAX. MAX. MAX.

UNIT NOTES

IDD0

Operating Current - One Bank Active-Precharge

tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRASmin(IDD);

CKE is HIGH, CS is HIGH between valid commands;

Address and control inputs are SWITCHING;

Databus inputs are SWITCHING.

70 60 55 mA 1, 2, 3, 4,

5, 6

IDD1

Operating Current - One Bank Active-Read-

Precharge

IOUT = 0 mA;

BL = 4, CL = CL(IDD), AL = 0;

tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRASmin(IDD), tRCD

= tRCD(IDD);

CKE is HIGH, CS is HIGH between valid commands;

Address and control inputs are SWITCHING;

Data bus inputs are SWITCHING.

80 70 65 mA 1, 2, 3, 4,

5, 6

IDD2P

Precharge Power-Down Current

All banks idle;

tCK = tCK(IDD);

CKE is LOW;

Other control and address inputs are STABLE;

Data Bus inputs are FLOATING.

6 6 6 mA

1, 2, 3, 4,

5, 6

IDD2N

Precharge Standby Current

All banks idle;

tCK = tCK(IDD);

CKE is HIGH, CS is HIGH;

Other control and address inputs are SWITCHING;

Data bus inputs are SWITCHING.

45 40 35 mA

1, 2, 3, 4,

5, 6

IDD2Q

Precharge Quiet Standby Current

All banks idle;

tCK = tCK(IDD);

CKE is HIGH, CS is HIGH;

Other control and address inputs are STABLE;

Data bus inputs are FLOATING.

35 35 30 mA

1, 2, 3, 4,

5, 6

IDD3PF Fast PDN Exit

MRS(12) = 0 15 15 15

IDD3PS

Active Power-Down Current

All banks open;

tCK = tCK(IDD);

CKE is LOW;

Other control and address inputs are

STABLE;

Data bus inputs are FLOATING.

Slow PDN Exit

MRS(12) = 1 10 10 10

mA 1, 2, 3, 4,

5, 6

IDD3N

Active Standby Current

All banks open;

tCK = tCK(IDD); tRAS = tRASmax(IDD), tRP = tRP(IDD);

CKE is HIGH, CS is HIGH between valid commands;

Other control and address inputs are SWITCHING;

Data bus inputs are SWITCHING.

60 50 45 mA

1, 2, 3, 4,

5, 6

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 41 - Revision A01

IDD4R

Operating Burst Read Current

All banks open, Continuous burst reads, IOUT = 0 mA;

BL = 4, CL = CL(IDD), AL = 0;

tCK = tCK(IDD); tRAS = tRASmax(IDD), tRP = tRP(IDD);

CKE is HIGH, CS is HIGH between valid commands;

Address inputs are SWITCHING;

Data Bus inputs are SWITCHING.

125 105 95 mA

1, 2, 3, 4,

5, 6

IDD4W

Operating Burst Write Current

All banks open, Continuous burst writes;

BL = 4, CL = CL(IDD), AL = 0;

tCK = tCK(IDD); tRAS = tRASmax(IDD), tRP = tRP(IDD);

CKE is HIGH, CS is HIGH between valid commands;

Address inputs are SWITCHING;

Data Bus inputs are SWITCHING.

130 110 100 mA

1, 2, 3, 4,

5, 6

IDD5B

Burst Refresh Current

tCK = tCK(IDD);

Refresh command every tRFC(IDD) interval;

CKE is HIGH, CS is HIGH between valid commands;

Other control and address inputs are SWITCHING;

Data bus inputs are SWITCHING.

75 70 65 mA

1, 2, 3, 4,

5, 6

IDD6

Self Refresh Current

CKE ≦ 0.2 V, external clock off, CLK and CLK at 0 V;

Other control and address inputs are FLOATING;

Data bus inputs are FLOATING.

6 6 6 mA

1, 2, 3, 4,

5, 6

IDD7

Operating Bank Interleave Read Current

All bank interleaving reads, IOUT = 0mA;

BL = 4, CL = CL(IDD), AL = tRCD(IDD) - 1 x tCK(IDD);

tCK = tCK(IDD), tRC = tRC(IDD), tRRD = tRRD(IDD), tRCD =

tRCD(IDD);

CKE is HIGH, CS is HIGH between valid commands;

Address bus inputs are STABLE during deselects;

Data Bus inputs are SWITCHING.

160 135 115 mA 1, 2, 3, 4,

5, 6

Notes:

1. VDD = 1.8 V± 0.1V; VDDQ = 1.8 V± 0.1V.

2. IDD specifications are tested after the device is properly initialized.

3. Input slew rate is specified by AC Parametric Test Condition.

4. IDD parameters are specified with ODT disabled.

5. Data Bus consists of DQ, LDM, UDM, LDQS, LDQS , UDQS and UDQS .

6. Definitions for IDD

LOW = Vin ≦ VIL (ac) (max)

HIGH = Vin ≧ VIH (ac) (min)

STABLE = inputs stable at a HIGH or LOW level

FLOATING = inputs at VREF = VDDQ/2

SWITCHING = inputs changing between HIGH and LOW every other clock cycle (once per two clocks) for address and

control signals, and inputs changing between HIGH and LOW every other data transfer (once per clock)

for DQ signals not including masks or strobes.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 42 - Revision A01

9.10 IDD Measurement Test Parameters

SPEED GRADE DDR2-1066

(-18)

DDR2-800

(-25/25I/25A)

DDR2-667

(-3)

Bin(CL-tRCD-tRP) 7-7-7 5-5-5/6-6-6 5-5-5

UNIT

CL(IDD) 7 5/6 5 tCK

tCK(IDD) 1.875 2.5 3 nS

tRCD(IDD) 13.125 12.5 15 nS

tRP(IDD) 13.125 12.5 15 nS

tRC(IDD) 53.125 52.5 55 nS

tRASmin(IDD) 40 40 40 nS

tRASmax(IDD) 70000 70000 70000 nS

tRRD(IDD)-1KB 7.5 7.5 7.5 nS

tFAW(IDD)-1KB 35 35 37.5 nS

tRFC(IDD) 75 75 75 nS

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 43 - Revision A01

9.11 AC Characteristics

9.11.1 AC Characteristics and Operating Condition for -18 speed grade

SPEED GRADE DDR2-1066 (-18)

Bin(CL-tRCD-tRP) 7-7-7

SYM.

PARAMETER MIN. MAX.

UNIT25 NOTES

tRCD Active to Read/Write Command Delay Time 13.125 − nS 23

tRP Precharge to Active Command Period 13.125 − nS 23

tRC Active to Ref/Active Command Period 53.125 − nS 23

tRAS Active to Precharge Command Period 40 70000 nS 4,23

tRFC Auto Refresh to Active/Auto Refresh command period 75 − nS 5

0°C ≦ TCASE ≦ 85°C − 7.8 μS 5

tREFI Average periodic

refresh Interval 85°C < TCASE ≦ 95°C − 3.9 μS 5,6

tCCD CAS to CAS command delay 2 − nCK

tCK(avg) @ CL=4 3.75 7.5 nS 30,31

tCK(avg) @ CL=5 3 7.5 nS 30,31

tCK(avg) @ CL=6 2.5 7.5 nS 30,31

tCK(avg) Average clock period

tCK(avg) @ CL=7 1.875 7.5 nS 30,31

tCH(avg) Average clock high pulse width 0.48 0.52 tCK(avg) 30,31

tCL(avg) Average clock low pulse width 0.48 0.52 tCK(avg) 30,31

tAC DQ output access time from CLK/ CLK -350 350 pS 35

tDQSCK DQS output access time from CLK / CLK -325 325 pS 35

tDQSQ DQS-DQ skew for DQS & associated DQ signals − 175 pS 13

tCKE CKE minimum high and low pulse width 3 − nCK 7

tRRD Active to active command period for 1KB page size 7.5 − nS 8,23

tFAW Four Activate Window for 1KB page size 35 nS 23

tWR Write recovery time 15 − nS 23

tDAL Auto-precharge write recovery + precharge time WR + tnRP − nCK 24

tWTR Internal Write to Read command delay 7.5 − nS 9,23

tRTP Internal Read to Precharge command delay 7.5 − nS 4,23

tIS (base) Address and control input setup time 125 − pS 10,26,

40,42,43

tIH (base) Address and control input hold time 200 − pS 11,26,

40,42,43

tIS (ref) Address and control input setup time 325 − pS 10,26,

40,42,43

tIH (ref) Address and control input hold time 325 − pS 11,26,

40,42,43

tIPW Address and control input pulse width for each input 0.6 − tCK(avg)

tDQSS DQS latching rising transitions to associated clock edges -0.25 0.25 tCK(avg) 28

tDSS DQS falling edge to CLK setup time 0.2 − tCK(avg) 28

tDSH DQS falling edge hold time from CLK 0.2 − tCK(avg) 28

tDQSH DQS input high pulse width 0.35 − tCK(avg)

tDQSL DQS input low pulse width 0.35 − tCK(avg)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 44 - Revision A01

AC Characteristics and Operating Condition for -18 speed grade, continued

SPEED GRADE DDR2-1066 (-18)

Bin(CL-tRCD-tRP) 7-7-7

SYM.

PARAMETER MIN. MAX.

UNITS25 NOTES

tWPRE Write preamble 0.35 − tCK(avg)

tWPST Write postamble 0.4 0.6 tCK(avg) 12

tRPRE Read preamble 0.9 1.1 tCK(avg) 14,36

tRPST Read postamble 0.4 0.6 tCK(avg) 14,37

tDS(base) DQ and DM input setup time 0 − pS 16,27,29,

41,42,44

tDH(base) DQ and DM input hold time 75 − pS 17,27,29,

41,42,44

tDS(ref) DQ and DM input setup time 200 − pS 16,27,29,

41,42,44

tDH(ref) DQ and DM input hold time 200 − pS 17,27,29,

41,42,44

tDIPW DQ and DM input pulse width for each input 0.35 − tCK(avg)

tHZ Data-out high-impedance time from CLK/ CLK − tAC,max pS 15,35

tLZ(DQS) DQS/ DQS -low-impedance time from CLK/ CLK tAC,min tAC,max pS 15,35

tLZ(DQ) DQ low-impedance time from CLK/ CLK 2 x tAC,min tAC,max pS 15,35

tHP Clock half pulse width Min. (tCH(abs),

tCL(abs)) − pS 32

tQHS Data hold skew factor − 250 pS 33

tQH DQ/DQS output hold time from DQS tHP - tQHS − pS 34

tXSNR Exit Self Refresh to a non-Read command tRFC + 10 − nS 23

tXSRD Exit Self Refresh to a Read command 200 − nCK

tXP Exit precharge power down to any command 3 − nCK

tXARD Exit active power down to Read command 3 − nCK 18

tXARDS Exit active power down to Read command

(slow exit, lower power) 10 - AL − nCK 18,19

tAOND ODT turn-on delay 2 2 nCK 20

tAON ODT turn-on tAC,min tAC,max + 2.575 nS 20,35

tAONPD ODT turn-on (Power Down mode) tAC,min + 2 3 x tCK(avg) +

tAC,max+1 nS

tAOFD ODT turn-off delay 2.5 2.5 nCK 21,39

tAOF ODT turn-off tAC,min tAC,max + 0.6 nS 21,38,39

tAOFPD ODT turn-off (Power Down mode) tAC,min + 2 2.5 x tCK(avg) +

tAC,max + 1 nS

tANPD ODT to power down Entry Latency 4 − nCK

tAXPD ODT Power Down Exit Latency 11 nCK

tMRD Mode Register Set command cycle time 2 − nCK

tMOD MRS command to ODT update delay 0 12 nS 23

tOIT OCD Drive mode output delay 0 12 nS 23

tDELAY Minimum time clocks remain ON after CKE

asynchronously drops LOW tIS+tCK(avg)+tIH − nS 22

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 45 - Revision A01

9.11.2 AC Characteristics and Operating Condition for -25/25I/25A/-3 speed grade

SPEED GRADE DDR2-800

(-25/25I/25A)

DDR2-667

(-3)

Bin(CL-tRCD-tRP) 5-5-5/6-6-6 5-5-5

SYM.

PARAMETER MIN. MAX. MIN. MAX.

UNITS25 NOTES

tRCD Active to Read/Write Command Delay Time 12.5 − 15 − nS 23

tRP Precharge to Active Command Period 12.5 − 15 − nS 23

tRC Active to Ref/Active Command Period 52.5 − 55 − nS 23

tRAS Active to Precharge Command Period 40 70000 40 70000 nS 4,23

tRFC Auto Refresh to Active/Auto Refresh command

period 75 − 75 − nS 5

0°C ≦ TCASE ≦ 85°C− 7.8 − 7.8 μS 5

tREFI Average periodic

refresh Interval 85°C < TCASE ≦ 95°C− 3.9 − 3.9 μS 5,6

tCCD CAS to CAS command delay 2 − 2 − nCK

tCK(avg) @ CL=3 5 8 5 8 nS 30,31

tCK(avg) @ CL=4 3.75 8 3.75 8 nS 30,31

tCK(avg) @ CL=5 2.5 8 3 8 nS 30,31

tCK(avg) Average clock period

tCK(avg) @ CL=6 2.5 8 − − nS 30,31

tCH(avg) Average clock high pulse width 0.48 0.52 0.48 0.52 tCK(avg) 30,31

tCL(avg) Average clock low pulse width 0.48 0.52 0.48 0.52 tCK(avg) 30,31

tAC DQ output access time from CLK/ CLK -400 400 -450 450 pS 35

tDQSCK DQS output access time from CLK / CLK -350 350 -400 400 pS 35

tDQSQ DQS-DQ skew for DQS & associated DQ signals − 200 − 240 pS 13

tCKE CKE minimum high and low pulse width 3 − 3 − nCK 7

tRRD Active to active command period for 1KB page

size 7.5 − 7.5 − nS 8,23

tFAW Four Activate Window for 1KB page size 35 − 37.5 − nS 23

tWR Write recovery time 15 − 15 − nS 23

tDAL Auto-precharge write recovery + precharge time WR + tnRP − WR + tnRP − nCK 24

tWTR Internal Write to Read command delay 7.5 − 7.5 − nS 9,23

tRTP Internal Read to Precharge command delay 7.5 − 7.5 − nS 4,23

tIS (base) Address and control input setup time 175 − 200 − pS 10,26,

40,42,43

tIH (base) Address and control input hold time 250 − 275 − pS 11,26,

40,42,43

tIS (ref) Address and control input setup time 375 − 400 − pS 10,26,

40,42,43

tIH (ref) Address and control input hold time 375 − 400 − pS 11,26,

40,42,43

tIPW Address and control input pulse width for each

input 0.6 − 0.6 − tCK(avg)

tDQSS DQS latching rising transitions to associated

clock edges -0.25 0.25 -0.25 0.25 tCK(avg) 28

tDSS DQS falling edge to CLK setup time 0.2 − 0.2 − tCK(avg) 28

tDSH DQS falling edge hold time from CLK 0.2 − 0.2 − tCK(avg) 28

tDQSH DQS input high pulse width 0.35 − 0.35 − tCK(avg)

tDQSL DQS input low pulse width 0.35 − 0.35 − tCK(avg)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 46 - Revision A01

AC Characteristics and Operating Condition for -25/25I/25A/-3 speed grades, continued

SPEED GRADE DDR2-800

(-25/25I/25A)

DDR2-667

(-3)

Bin(CL-tRCD-tRP) 5-5-5/6-6-6 5-5-5

SYM.

PARAMETER MIN. MAX. MIN. MAX.

UNITS25 NOTES

tWPRE Write preamble 0.35 − 0.35 − tCK(avg)

tWPST Write postamble 0.4 0.6 0.4 0.6 tCK(avg) 12

tRPRE Read preamble 0.9 1.1 0.9 1.1 tCK(avg) 14,36

tRPST Read postamble 0.4 0.6 0.4 0.6 tCK(avg) 14,37

tDS(base) DQ and DM input setup time 50 − 100 − pS 16,27,29,

41,42,44

tDH(base) DQ and DM input hold time 125 − 175 − pS 17,27,29,

41,42,44

tDS(ref) DQ and DM input setup time 250 − 300 − pS 16,27,29,

41,42,44

tDH(ref) DQ and DM input hold time 250 − 300 − pS 17,27,29,

41,42,44

tDIPW DQ and DM input pulse width for each

input 0.35 − 0.35 − tCK(avg)

tHZ Data-out high-impedance time from

CLK/ CLK − tAC,max − tAC,max pS 15,35

tLZ(DQS)

DQS/ DQS -low-impedance time from

CLK/ CLK

tAC,min tAC,max tAC,min tAC,max pS 15,35

tLZ(DQ) DQ low-impedance time from CLK/ CLK 2 x tAC,min tAC,max 2 x tAC,min tAC,max pS 15,35

tHP Clock half pulse width

Min.

(tCH(abs),

tCL(abs))

Min.

(tCH(abs),

tCL(abs))

pS 32

tQHS Data hold skew factor − 300 − 340 pS 33

tQH DQ/DQS output hold time from DQS tHP - tQHS − tHP - tQHS − pS 34

tXSNR Exit Self Refresh to a non-Read command tRFC + 10 − tRFC + 10 − nS 23

tXSRD Exit Self Refresh to a Read command 200 − 200 − nCK

tXP Exit precharge power down to any

command 2 − 2 − nCK

tXARD Exit active power down to Read command 2 − 2 − nCK 18

tXARDS Exit active power down to Read command

(slow exit, lower power) 8 - AL − 7 - AL − nCK 18,19

tAOND ODT turn-on delay 2 2 2 2 nCK 20

tAON ODT turn-on tAC,min tAC,max + 0.7 tAC,min tAC,max + 0.7 nS 20,35

tAONPD ODT turn-on (Power Down mode) tAC,min + 2 2 x tCK(avg) +

tAC,max + 1tAC,min + 2 2 x tCK(avg) +

tAC,max + 1 nS

tAOFD ODT turn-off delay 2.5 2.5 2.5 2.5 nCK 21,39

tAOF ODT turn-off tAC,min tAC,max + 0.6 tAC,min tAC,max + 0.6 nS 21,38,39

tAOFPD ODT turn-off (Power Down mode) tAC,min + 2 2.5 x tCK(avg)

+ tAC,max + 1tAC,min + 2 2.5 x tCK(avg)

+ tAC,max + 1 nS

tANPD ODT to power down Entry Latency 3 − 3 − nCK

tAXPD ODT Power Down Exit Latency 8 8 nCK

tMRD Mode Register Set command cycle time 2 − 2 − nCK

tMOD MRS command to ODT update delay 0 12 0 12 nS 23

tOIT OCD Drive mode output delay 0 12 0 12 nS 23

tDELAY Minimum time clocks remain ON after

CKE asynchronously drops LOW

tIS+tCK(avg)+

tIH − tIS+tCK(avg)+

tIH − nS 22

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 47 - Revision A01

Notes:

1. All voltages are referenced to VSS.

2. Tests for AC timing, IDD, and electrical AC and DC characteristics may be conducted at nominal reference/supply voltage

levels, but the related specifications and device operation are guaranteed for the full voltage range specified. ODT is

disabled for all measurements that are not ODT-specific.

3. AC timing reference load:

DQS

Output

Timing

reference

point

VTT = VDDQ/2

25Ω

VDDQ

DUT

Figure 16 — AC timing reference load

4. This is a minimum requirement. Minimum read to precharge timing is AL + BL / 2 provided that the tRTP and tRAS(min)

have been satisfied.

5. If refresh timing is violated, data corruption may occur and the data must be re-written with valid data before a valid READ

can be executed.

6. This is an optional feature. For detailed information, please refer to “operating temperature condition” section 9.2 in this data

sheet.

7. tCKE min of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the

valid input level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not

transition from its valid level during the time period of tIS + 2 x tCK + tIH.

8. A minimum of two clocks (2 *nCK) is required irrespective of operating frequency.

9. tWTR is at least two clocks (2 * nCK) independent of operation frequency.

10. There are two sets of values listed for Command/Address input setup time: tIS(base) and tIS(ref). The tIS(ref) value (for

reference only) is equivalent to the baseline value of tIS(base) at VREF when the slew rate is 1.0 V/nS. The baseline value

tIS(base) is the JEDEC defined value, referenced from the input signal crossing at the VIH(ac) level for a rising signal and

VIL(ac) for a falling signal applied to the device under test. See Figure 17. If the Command/Address slew rate is not equal to

1.0 V/nS, then the baseline values must be derated by adding the values from table of tIS/tIH derating values for DDR2-667,

DDR2-800 and DDR2-1066 (page 55).

CLK

tIS(base) tIH(base) tIS(base) tIH(base)

VDDQ

VIH(ac) min

VIH(dc) min

VREF(dc)

VIL(dc) max

VIL(ac) max

VSS

tIS(ref) tIH(ref) tIS(ref) tIH(ref)

Logic levels

VREF levels

Figure 17 — Differential input waveform timing – tIS and tIH

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 48 - Revision A01

11. There are two sets of values listed for Command/Address input hold time: tIH(base) and tIH(ref). The tIH(ref) value (for

reference only) is equivalent to the baseline value of tIH(base) at VREF when the slew rate is 1.0 V/nS. The baseline value

tIH(base) is the JEDEC defined value, referenced from the input signal crossing at the VIL(dc) level for a rising signal and

VIH(dc) for a falling signal applied to the device under test. See Figure 17. If the Command/Address slew rate is not equal to

1.0 V/nS, then the baseline values must be derated by adding the values from table tIS/tIH derating values for DDR2-667,

DDR2-800 and DDR2-1066 (page 55).

12. The maximum limit for the tWPST parameter is not a device limit. The device operates with a greater value for this

parameter, but system performance (bus turnaround) will degrades accordingly.

13. tDQSQ: Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as

well as output Slew Rate mismatch between DQS / DQS and associated DQ in any given cycle.

14. tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is

no longer driving (tRPST), or begins driving (tRPRE). Figure 18 shows a method to calculate these points when the device

is no longer driving (tRPST), or begins driving (tRPRE) by measuring the signal at two different voltages. The actual voltage

measurement points are not critical as long as the calculation is consistent.

15. tHZ and tLZ transitions occur in the same access time as valid data transitions. These parameters are referenced to a

specific voltage level which specifies when the device output is no longer driving (tHZ), or begins driving (tLZ). Figure 18

shows a method to calculate the point when device is no longer driving (tHZ), or begins driving (tLZ) by measuring the

signal at two different voltages. The actual voltage measurement points are not critical as long as the calculation is

consistent. tLZ(DQ) refers to tLZ of the DQ’s and tLZ(DQS) refers to tLZ of the (UDQS, LDQS, UDQS and LDQS ) each

treated as single-ended signal.

VOH - x mV

VTT - 2x mV

VTT - x mV

VOH - 2x mV

VOL + 2x mV

VOL + x mV

VTT + x mV

VTT + 2x mV

tRPST end point tRPRE begin point

tHZ,tRPST end point = 2 x T1 - T2 tLZ,tRPRE begin point = 2 x T1 - T2

tHZ

T1 T2

tLZ

T1 T2

Figure 18 — Method for calculating transitions and endpoints

16. Input waveform timing tDS with differential data strobe enabled MR[bit10]=0. There are two sets of values listed for DQ and

DM input setup time: tDS(base) and tDS(ref). The tDS(ref) value (for reference only) is equivalent to the baseline value

tDS(base) at VREF when the slew rate is 2.0 V/nS, differentially. The baseline value tDS(base) is the JEDEC defined value,

referenced from the input signal crossing at the VIH(ac) level to the differential data strobe crosspoint for a rising signal, and

from the input signal crossing at the VIL(ac) level to the differential data strobe crosspoint for a falling signal applied to the

device under test. DQS, DQS signals must be monotonic between VIL(dc)max and VIH(dc)min. See Figure 19. If the

differential DQS slew rate is not equal to 2.0 V/nS, then the baseline values must be derated by adding the values from

table of DDR2-667, DDR2-800 and DDR2-1066 tDS/tDH derating with differential data strobe (page 60).

17. Input waveform timing tDH with differential data strobe enabled MR[bit10]=0. There are two sets of values listed for DQ and

DM input hold time: tDH(base) and tDH(ref). The tDH(ref) value (for reference only) is equivalent to the baseline value

tDH(base) at VREF when the slew rate is 2.0 V/nS, differentially. The baseline value tDH(base) is the JEDEC defined value,

referenced from the differential data strobe crosspoint to the input signal crossing at the VIH(dc) level for a falling signal and

from the differential data strobe crosspoint to the input signal crossing at the VIL(dc) level for a rising signal applied to the

device under test. DQS, DQS signals must be monotonic between VIL(dc)max and VIH(dc)min. See Figure 19. If the

differential DQS slew rate is not equal to 2.0 V/nS, then the baseline values must be derated by adding the values from

table of DDR2-667, DDR2-800 and DDR2-1066 tDS/tDH derating with differential data strobe (page 60).

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 49 - Revision A01

DQS

tDS(base) tDH(base) tDS(base) tDH(base)

VDDQ

VIH(ac) min

VIH(dc) min

VREF(dc)

VIL(dc) max

VIL(ac) max

VSS

tDS(ref) tDH(ref) tDS(ref) tDH(ref)

Logic levels

VREF levels

Figure 19 — Differential input waveform timing – tDS and tDH

18. User can choose which active power down exit timing to use via MRS (bit 12). tXARD is expected to be used for fast active

power down exit timing. tXARDS is expected to be used for slow active power down exit timing.

19. AL = Additive Latency.

20. ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time

max is when the ODT resistance is fully on. Both are measure from tAOND, which is interpreted differently per speed bin.

For DDR2-667/800/1066, tAOND is 2 clock cycles after the clock edge that registered a first ODT HIGH counting the actual

input clock edges.

21. ODT turn off time min is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high

impedance. Both are measured from tAOFD.

For DDR2-667/800: This is interpreted differently per speed bin. If tCK(avg) = 3 nS is assumed, tAOFD is 1.5 nS (=

0.5 x 3 nS) after the second trailing clock edge counting from the clock edge that registered a first ODT LOW and by

counting the actual input clock edges.

For DDR2-1066: This is interpreted as 0.5 x tCK(avg) [nS] after the second trailing clock edge counting from the

clock edge that registered a first ODT LOW and by counting the actual input clock edges. tAOFD is 0.9375 [nS] (=

0.5 x 1.875 [nS]) after the second trailing clock edge counting from the clock edge that registered a first ODT LOW

and by counting the actual input clock edges.

22. The clock frequency is allowed to change during Self Refresh mode or precharge power-down mode. In case of clock

frequency change during precharge power-down, a specific procedure is required as described in section 7.10.

23. For these parameters, the DDR2 SDRAM device is characterized and verified to support tnPARAM = RU{tPARAM /

tCK(avg)}, which is in clock cycles, assuming all input clock jitter specifications are satisfied.

Examples:

The device will support tnRP = RU{tRP / tCK(avg)}, which is in clock cycles, if all input clock jitter specifications are

met. This means: For DDR2-667 5-5-5, of which tRP = 15nS, the device will support tnRP = RU{tRP / tCK(avg)} = 5,

i.e. as long as the input clock jitter specifications are met, Precharge command at Tm and Active command at Tm+5

is valid even if (Tm+5 - Tm) is less than 15nS due to input clock jitter. For DDR2-1066 7-7-7, of which tRP = 13.125

nS, the device will support tnRP = RU{tRP / tCK(avg)} = 7, i.e. as long as the input clock jitter specifications are met,

Precharge command at Tm and Active command at Tm+7 is valid even if (Tm+7 - Tm) is less than 13.125 nS due to

input clock jitter.

24. tDAL [nCK] = WR [nCK] + tnRP [nCK] = WR + RU {tRP [pS] / tCK(avg) [pS] }, where WR is the value programmed in the

mode register set and RU stands for round up.

Example:

For DDR2-1066 7-7-7 at tCK(avg) = 1.875 nS with WR programmed to 8 nCK, tDAL = 8 + RU{13.125 nS / 1.875

nS} [nCK] = 8 + 7 [nCK] = 15 [nCK].

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 50 - Revision A01

25. New units, ‘tCK(avg)’ and ‘nCK’, are introduced in DDR2-667, DDR2-800.

Unit ‘tCK(avg)’ represents the actual tCK(avg) of the input clock under operation.

Unit ‘nCK’ represents one clock cycle of the input clock, counting the actual clock edges.

Examples:

For DDR2-667/800: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command may be

registered at Tm+2, even if (Tm+2 - Tm) is 2 x tCK(avg) + tERR(2per),min.

For DDR2-1066: tXP = 3 [nCK] means; if Power Down exit is registered at Tm, an Active command may be

registered at Tm+3, even if (Tm+3 - Tm) is 3 x tCK(avg) + tERR(3per),min.

26. These parameters are measured from a command/address signal (CKE, CS , RAS , CAS , WE , ODT, BA0, A0, A1, etc.)

transition edge to its respective clock signal (CLK/ CLK ) crossing. The spec values are not affected by the amount of clock

jitter applied (i.e. tJIT(per), tJIT(cc), etc.), as the setup and hold are relative to the clock signal crossing that latches the

command/address. That is, these parameters should be met whether clock jitter is present or not.

27. If tDS or tDH is violated, data corruption may occur and the data must be re-written with valid data before a valid READ can

be executed.

28. These parameters are measured from a data strobe signal ((L/U)DQS/ DQS ) crossing to its respective clock signal

(CLK/ CLK ) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT(per), tJIT(cc), etc.), as

these are relative to the clock signal crossing. That is, these parameters should be met whether clock jitter is present or not.

29. These parameters are measured from a data signal ((L/U)DM, (L/U)DQ0, (L/U)DQ1, etc.) transition edge to its respective

data strobe signal ((L/U)DQS/ DQS ) crossing.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 51 - Revision A01

30. Input clock jitter spec parameter. These parameters and the ones in the table below are referred to as 'input clock jitter spec

parameters'. The jitter specified is a random jitter meeting a Gaussian distribution.

Input clock-Jitter specifications parameters for DDR2-667, DDR2-800 and DDR2-1066

DDR2-667 DDR2-800 DDR2-1066

PARAMETER SYMBOL

MIN. MAX. MIN. MAX. MIN. MAX. UNIT

Clock period jitter tJIT(per) -125 125 -100 100 -90 90 pS

Clock period jitter during DLL locking period tJIT(per,lck) -100 100 -80 80 -80 80 pS

Cycle to cycle clock period tJIT(cc) -250 250 -200 200 -180 180 pS

Cycle to cycle clock period jitter during DLL

locking period

tJIT(cc,lck) -200 200 -160 160 -160 160 pS

Cumulative error across 2 cycles tERR(2per) -175 175 -150 150 -132 132 pS

Cumulative error across 3 cycles tERR(3per) -225 225 -175 175 -157 157 pS

Cumulative error across 4 cycles tERR(4per) -250 250 -200 200 -175 175 pS

Cumulative error across 5 cycles tERR(5per) -250 250 -200 200 -188 188 pS

Cumulative error across n cycles,

n = 6 ... 10, inclusive

tERR(6-10per) -350 350 -300 300 -250 250 pS

Cumulative error across n cycles,

n = 11 ... 50, inclusive

tERR(10-50per) -450 450 -450 450 -425 425 pS

Duty cycle jitter tJIT(duty) -125 125 -100 100 -75 75 pS

Definitions:

- tCK(avg)

tCK(avg) is calculated as the average clock period across any consecutive 200 cycle window.

tCK(avg) = ⎥

⎦

⎤

⎢

⎣

⎡∑

tCK

/ N

where N = 200

- tCH(avg) and tCL(avg)

tCH(avg) is defined as the average HIGH pulse width, as calculated across any consecutive 200 HIGH pulses.

tCH(avg) = ⎥

⎦

⎤

⎢

⎣

⎡∑

tCH

/ (N × tCK(avg))

where N = 200

tCL(avg) is defined as the average LOW pulse width, as calculated across any consecutive 200 LOW pulses.

tCL(avg) = ⎥

⎦

⎤

⎢

⎣

⎡∑

tCL

/ (N × tCK(avg))

where N = 200

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 52 - Revision A01

- tJIT(duty)

tJIT(duty) is defined as the cumulative set of tCH jitter and tCL jitter. tCH jitter is the largest deviation of any single tCH from

tCH(avg). tCL jitter is the largest deviation of any single tCL from tCL(avg).

tJIT(duty) = Min/max of {tJIT(CH), tJIT(CL)}

where,

tJIT(CH) = {tCHi- tCH(avg) where i=1 to 200}

tJIT(CL) = {tCLi- tCL(avg) where i=1 to 200}

- tJIT(per), tJIT(per,lck)

tJIT(per) is defined as the largest deviation of any single tCK from tCK(avg).

tJIT(per) = Min/max of {tCKi- tCK(avg) where i=1 to 200}

tJIT(per) defines the single period jitter when the DLL is already locked.

tJIT(per,lck) uses the same definition for single period jitter, during the DLL locking period only.

tJIT(per) and tJIT(per,lck) are not guaranteed through final production testing.

- tJIT(cc), tJIT(cc,lck)

tJIT(cc) is defined as the difference in clock period between two consecutive clock cycles:

tJIT(cc) = Max of |tCKi+1 – tCKi|

tJIT(cc) defines the cycle to cycle jitter when the DLL is already locked.

tJIT(cc,lck) uses the same definition for cycle to cycle jitter, during the DLL locking period only.

tJIT(cc) and tJIT(cc,lck) are not guaranteed through final production testing.

- tERR(2per), tERR (3per), tERR (4per), tERR (5per), tERR (6-10per) and tERR (11-50per)

tERR is defined as the cumulative error across multiple consecutive cycles from tCK(avg).

tERR(nper) = ⎥

⎦

⎤

⎢

⎣

⎡∑

−+

tCK –n × tCK(avg)

Where

⎢

⎣

⎡

≤≤

50per)–R(11for tER 50 n 11

10per)–R(6for tER 10 n 6

R(5per)for tER 5 =n

R(4per)for tER 4 =n

R(3per)for tER 3 =n

R(2per)for tER 2 =n

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 53 - Revision A01

31. These parameters are specified per their average values, however it is understood that the following relationship between

the average timing and the absolute instantaneous timing holds at all times. (Min and max of SPEC values are to be used

for calculations in the table below.)

PARAMETER SYMBOL MIN MAX UNIT

Absolute clock period tCK(abs) tCK(avg),min + tJIT(per),min tCK(avg),max + tJIT(per),max pS

Absolute clock HIGH pulse width tCH(abs) tCH(avg),min x tCK(avg),min +

tJIT(duty),min

tCH(avg),max x tCK(avg),max +

tJIT(duty),max

Absolute clock LOW pulse width tCL(abs) tCL(avg),min x tCK(avg),min +

tJIT(duty),min

tCL(avg),max x tCK(avg),max +

tJIT(duty),max

Examples: 1) For DDR2-667, tCH(abs),min = ( 0.48 x 3000 pS ) - 125 pS = 1315 pS

2) For DDR2-1066, tCH(abs),min = ( 0.48 x 1875 pS ) - 75 pS = 825 pS

32. tHP is the minimum of the absolute half period of the actual input clock. tHP is an input parameter but not an input

specification parameter. It is used in conjunction with tQHS to derive the DRAM output timing tQH. The value to be used for

tQH calculation is determined by the following equation;

tHP = Min ( tCH(abs), tCL(abs) ),

where,

tCH(abs) is the minimum of the actual instantaneous clock HIGH time;

tCL(abs) is the minimum of the actual instantaneous clock LOW time;

33. tQHS accounts for:

1) The pulse duration distortion of on-chip clock circuits, which represents how well the actual tHP at the input is

transferred to the output; and

2) The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next transition,

both of which are independent of each other, due to data pin skew, output pattern effects, and p-channel to n-

channel variation of the output drivers

34. tQH = tHP – tQHS, where:

tHP is the minimum of the absolute half period of the actual input clock; and

tQHS is the specification value under the max column.

{The less half-pulse width distortion present, the larger the tQH value is; and the larger the valid data eye will be.}

Examples:

1) If the system provides tHP of 1315 pS into a DDR2-667 SDRAM, the DRAM provides tQH of 975 pS minimum.

2) If the system provides tHP of 1420 pS into a DDR2-667 SDRAM, the DRAM provides tQH of 1080 pS minimum.

3) If the system provides tHP of 825 pS into a DDR2-1066 SDRAM, the DRAM provides tQH of 575 pS minimum.

4) If the system provides tHP of 900 pS into a DDR2-1066 SDRAM, the DRAM provides tQH of 650 pS minimum.

35. When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(6-10per) of the

input clock. (output deratings are relative to the SDRAM input clock.)

Examples:

1) If the measured jitter into a DDR2-667 SDRAM has tERR(6-10per),min = - 272 pS and tERR(6-10per),max = +

293 pS, then tDQSCK,min(derated) = tDQSCK,min - tERR(6-10per),max = - 400 pS - 293 pS = - 693 pS and

tDQSCK,max(derated) = tDQSCK,max - tERR(6-10per),min = 400 pS + 272 pS = + 672 pS.

Similarly, tLZ(DQ) for DDR2-667 derates to tLZ(DQ),min(derated) = - 900 pS - 293 pS = - 1193 pS and

tLZ(DQ),max(derated) = 450 pS + 272 pS = + 722 pS. (Caution on the min/max usage!)

2) If the measured jitter into a DDR2-1066 SDRAM has tERR(6-10per),min = - 202 pS and tERR(6-10per),max = +

223 pS, then tDQSCK,min(derated) = tDQSCK,min - tERR(6-10per),max = - 300 pS - 223 pS = - 523 pS and

tDQSCK,max(derated) = tDQSCK,max - tERR(6-10per),min = 300 pS + 202 pS = + 502 pS.

Similarly, tLZ(DQ) for DDR2-1066 derates to tLZ(DQ),min(derated) = - 700 pS - 223 pS = - 923 pS and

tLZ(DQ),max(derated) = 350 pS + 202 pS = + 552 pS. (Caution on the min/max usage!)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 54 - Revision A01

36. When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT(per) of the input

clock. (output deratings are relative to the SDRAM input clock.)

Examples:

1) If the measured jitter into a DDR2-667 SDRAM has tJIT(per),min = - 72 pS and tJIT(per),max = + 93 pS, then

tRPRE,min(derated) = tRPRE,min + tJIT(per),min = 0.9 x tCK(avg) - 72 pS = + 2178 pS and tRPRE,max(derated) =

tRPRE,max + tJIT(per),max = 1.1 x tCK(avg) + 93 pS = + 2843 pS. (Caution on the min/max usage!)

2) If the measured jitter into a DDR2-1066 SDRAM has tJIT(per),min = - 72 pS and tJIT(per),max = + 63 pS, then

tRPRE,min(derated) = tRPRE,min + tJIT(per),min = 0.9 x tCK(avg) - 72 pS = + 1615.5 pS and tRPRE,max(derated)

= tRPRE,max + tJIT(per),max = 1.1 x tCK(avg) + 63 pS = + 2125.5 pS. (Caution on the min/max usage!)

37. When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT(duty) of the input

clock. (output deratings are relative to the SDRAM input clock.)

Examples:

1) If the measured jitter into a DDR2-667 SDRAM has tJIT(duty),min = - 72 pS and tJIT(duty),max = + 93 pS, then

tRPST,min(derated) = tRPST,min + tJIT(duty),min = 0.4 x tCK(avg) - 72 pS = + 928 pS and tRPST,max(derated) =

tRPST,max + tJIT(duty),max = 0.6 x tCK(avg) + 93 pS = + 1592 pS. (Caution on the min/max usage!)

2) If the measured jitter into a DDR2-1066 SDRAM has tJIT(duty),min = - 72 pS and tJIT(duty),max = + 63 pS, then

tRPST,min(derated) = tRPST,min + tJIT(duty),min = 0.4 x tCK(avg) - 72 pS = + 678 pS and tRPST,max(derated) =

tRPST,max + tJIT(duty),max = 0.6 x tCK(avg) + 63 pS = + 1188 pS. (Caution on the min/max usage!)

38. When the device is operated with input clock jitter, this parameter needs to be derated by { -tJIT(duty),max - tERR(6-

10per),max } and { - tJIT(duty),min - tERR(6-10per),min } of the actual input clock. (output deratings are relative to the

SDRAM input clock.)

Examples:

1) If the measured jitter into a DDR2-667 SDRAM has tERR(6-10per),min = - 272 pS, tERR(6-10per),max = + 293

pS, tJIT(duty),min = - 106 pS and tJIT(duty),max = + 94 pS, then tAOF,min(derated) = tAOF,min + { - tJIT(duty),max

- tERR(6-10per),max } = - 450 pS + { - 94 pS - 293 pS} = - 837 pS and tAOF,max(derated) = tAOF,max + { -

tJIT(duty),min - tERR(6-10per),min } = 1050 pS + { 106 pS + 272 pS } = + 1428 pS. (Caution on the min/max

usage!)

2) If the measured jitter into a DDR2-1066 SDRAM has tERR(6-10per),min = - 202 pS, tERR(6-10per),max = + 223

pS, tJIT(duty),min = - 66 pS and tJIT(duty),max = + 74 pS, then tAOF,min(derated) = tAOF,min + { - tJIT(duty),max -

tERR(6-10per),max } = - 350 pS + { - 74 pS - 223 pS} = - 647 pS and tAOF,max(derated) = tAOF,max + { -

tJIT(duty),min - tERR(6-10per),min } = 950 pS + { 66 pS + 202 pS } = + 1218 pS. (Caution on the min/max usage!)

39. For tAOFD of DDR2-667/800/1066, the 1/2 clock of nCK in the 2.5 x nCK assumes a tCH(avg), average input clock HIGH

pulse width of 0.5 relative to tCK(avg). tAOF,min and tAOF,max should each be derated by the same amount as the actual

amount of tCH(avg) offset present at the DRAM input with respect to 0.5.

Example:

If an input clock has a worst case tCH(avg) of 0.48, the tAOF,min should be derated by subtracting 0.02 x tCK(avg)

from it, whereas if an input clock has a worst case tCH(avg) of 0.52, the tAOF,max should be derated by adding

0.02 x tCK(avg) to it. Therefore, we have;

tAOF,min(derated) = tAC,min - [0.5 - Min(0.5, tCH(avg),min)] x tCK(avg)

tAOF,max(derated) = tAC,max + 0.6 + [Max(0.5, tCH(avg),max) - 0.5] x tCK(avg)

tAOF,min(derated) = Min(tAC,min, tAC,min - [0.5 - tCH(avg),min] x tCK(avg))

tAOF,max(derated) = 0.6 + Max(tAC,max, tAC,max + [tCH(avg),max - 0.5] x tCK(avg))

where tCH(avg),min and tCH(avg),max are the minimum and maximum of tCH(avg) actually measured at the DRAM

input balls.

Note that these deratings are in addition to the tAOF derating per input clock jitter, i.e. tJIT(duty) and tERR(6-10per). However

tAC values used in the equations shown above are from the timing parameter table and are not derated.

Thus the final derated values for tAOF are;

tAOF,min(derated_final) = tAOF,min(derated) + { - tJIT(duty),max - tERR(6-10per),max }

tAOF,max(derated_final) = tAOF,max(derated) + { - tJIT(duty),min - tERR(6-10per),min }

40. Timings are specified with command/address input slew rate of 1.0 V/nS.

41. Timings are specified with DQs and DM input slew rate of 1.0V/nS.

42. Timings are specified with CLK/ CLK differential slew rate of 2.0 V/nS. Timings are guaranteed for DQS signals with a

differential slew rate of 2.0 V/nS in differential strobe mode.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 55 - Revision A01

43. tIS and tIH (input setup and hold) derating.

tIS/tIH Derating values for DDR2-667, DDR2-800 and DDR2-1066

ΔtIS and ΔtIH Derating Values for DDR2-667, DDR2-800 and DDR2-1066

CLK/ CLK Differential Slew Rate

2.0 V/nS 1.5 V/nS 1.0 V/nS

Command/

Address

Slew Rate

(V/nS)

ΔtIS ΔtIH ΔtIS ΔtIH ΔtIS ΔtIH Unit

4.0 +150 +94 +180 +124 +210 +154 pS

3.5 +143 +89 +173 +119 +203 +149 pS

3.0 +133 +83 +163 +113 +193 +143 pS

2.5 +120 +75 +150 +105 +180 +135 pS

2.0 +100 +45 +130 +75 +160 +105 pS

1.5 +67 +21 +97 +51 +127 +81 pS

1.0 0 0 +30 +30 +60 +60 pS

0.9 -5 -14 +25 +16 +55 +46 pS

0.8 -13 -31 +17 -1 +47 +29 pS

0.7 -22 -54 +8 -24 +38 +6 pS

0.6 -34 -83 -4 -53 +26 -23 pS

0.5 -60 -125 -30 -95 0 -65 pS

0.4 -100 -188 -70 -158 -40 -128 pS

0.3 -168 -292 -138 -262 -108 -232 pS

0.25 -200 -375 -170 -345 -140 -315 pS

0.2 -325 -500 -295 -470 -265 -440 pS

0.15 -517 -708 -487 -678 -457 -648 pS

0.1 -1000 -1125 -970 -1095 -940 -1065 pS

For all input signals the total tIS (setup time) and tIH (hold time) required is calculated by adding the data sheet tIS(base) and

tIH(base) value to the ΔtIS and ΔtIH derating value respectively. Example: tIS (total setup time) = tIS(base) + ΔtIS.

Setup (tIS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF(dc) and the first

crossing of VIH(ac)min. Setup (tIS) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of

VREF(dc) and the first crossing of VIL(ac)max. If the actual signal is always earlier than the nominal slew rate line between

shaded ‘VREF(dc) to AC region’, use nominal slew rate for derating value. See Figure 20 Illustration of nominal slew rate for tIS.

If the actual signal is later than the nominal slew rate line anywhere between shaded ‘VREF(dc) to AC region’, the slew rate of a

tangent line to the actual signal from the AC level to DC level is used for derating value. See Figure 21 Illustration of tangent line

for tIS.

Hold (tIH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(dc)max and the first

crossing of VREF(dc). Hold (tIH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of

VIH(dc)min and the first crossing of VREF(dc). If the actual signal is always later than the nominal slew rate line between

shaded ‘DC to VREF(dc) region’, use nominal slew rate for derating value. See Figure 22 Illustration of nominal slew rate for tIH.

If the actual signal is earlier than the nominal slew rate line anywhere between shaded ‘DC to VREF(dc) region’, the slew rate of

a tangent line to the actual signal from the DC level to VREF(dc) level is used for derating value. See Figure 23 Illustration of

tangent line for tIH.

Although for slow slew rates the total setup time might be negative (i.e. a valid input signal will not have reached VIH/IL(ac) at

the time of the rising clock transition) a valid input signal is still required to complete the transition and reach VIH/IL(ac).

For slew rates in between the values listed in above tIS/tIH derating values for DDR2-667, DDR2-800 and DDR2-1066 table, the

derating values may obtained by linear interpolation.

These values are typically not subject to production test. They are verified by design and characterization.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 56 - Revision A01

CLK

tIS tIH tIS tIH

nominal

slew rate

nominal

slew rate

VREF to AC

region

VDDQ

VIH(ac)min

VIH(dc)min

VREF(dc)

VIL(dc)max

VIL(ac)max

VSS

ΔTF ΔTR

Setup Slew Rate

Falling Signal =

VREF(dc) -V

IL(ac)max Setup Slew Rate

Rising Signal =

VIH(ac)min -V

REF(dc)

VREF to AC

region

ΔTF ΔTR

Figure 20 —Illustration of nominal slew rate for tIS

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 57 - Revision A01

tIS tIH tIS tIH

tangent

line

tangent

line

VREF to AC

region

VDDQ

VIH(ac)min

VIH(dc)min

VREF(dc)

VIL(dc)max

VIL(ac)max

VSS

ΔTF

ΔTR

Setup Slew Rate

Falling Signal =tangent line[VREF(dc) -V

IL(ac)max]

VREF to AC

region

nominal

line

Setup Slew Rate

Rising Signal =

tangent line[VIH(ac)min -V

REF(dc)]

nominal

line

CLK

ΔTR

ΔTF

Figure 21 —Illustration of tangent line for tIS

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 58 - Revision A01

tIS tIH tIS tIH

nominal

slew rate

nominal

slew rate

DC to VREF

region

VDDQ

VIH(ac)min

VIH(dc)min

VREF(dc)

VIL(dc)max

VIL(ac)max

VSS

ΔTF

ΔTR

Hold Slew Rate

Rising Signal =VREF(dc) -V

IL(dc)max Hold Slew Rate

Falling Signal =

VIH(dc)min -V

REF(dc)

DC to VREF

region

CLK

ΔTR ΔTF

Figure 22 —Illustration of nominal slew rate for tIH

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 59 - Revision A01

tIS tIH tIS tIH

tangent

line

DC to VREF

region

VDDQ

VIH(ac)min

VIH(dc)min

VREF(dc)

VIL(dc)max

VIL(ac)max

VSS

ΔTFΔTR

DC to VREF

region

nominal

line

tangent

line

nominal

line

Hold Slew Rate

Rising Signal =tangent line[VREF(dc) -V

IL(ac)max]

Hold Slew Rate

Falling Signal =

tangent line[VIH(dc)min -V

REF(dc)]

CLK

ΔTR

ΔTF

Figure 23 —Illustration of tangent line for tIH

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 60 - Revision A01

44. Data setup and hold time derating.

DDR2-667, DDR2-800 and DDR2-1066 tDS/tDH derating with differential data strobe

ΔtDS, ΔtDH Derating Values for DDR2-667, DDR2-800 and DDR2-1066 (All units in ‘pS’; the note applies to

the entire table)

DQS/ DQS Differential Slew Rate

4.0 V/nS 3.0 V/nS 2.0 V/nS 1.8 V/nS 1.6 V/nS 1.4 V/nS 1.2 V/nS 1.0 V/nS 0.8 V/nS

Slew

Rate

(V/nS)

ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH

2.0 100 45 100 45 100 45 - - - - - - - - - - - -

1.5 67 21 67 21 67 21 79 33 - - - - - - - - - -

1.0 0 0 0 0 0 0 12 12 24 24 - - - - - - - -

0.9 - - -5 -14 -5 -14 7 -2 19 10 31 22 - - - - - -

0.8 - - - - -13 -31 -1 -19 11 -7 23 5 35 17 - - - -

0.7 - - - - - - -10 -42 2 -30 14 -18 26 -6 38 6 - -

0.6 - - - - - - - - -10 -59 2 -47 14 -35 26 -23 38 -11

0.5 - - - - - - - - - - -24 -89 -12 -77 0 -65 12 -53

0.4 - - - - - - - - - - - - -52 -140 -40 -128 -28 -116

For all input signals the total tDS (setup time) and tDH (hold time) required is calculated by adding the data sheet tDS(base) and

tDH(base) value to the ΔtDS and ΔtDH derating value respectively. Example: tDS (total setup time) = tDS(base) + ΔtDS.

Setup (tDS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF(dc) and the first

crossing of VIH(ac)min. Setup (tDS) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of

VREF(dc) and the first crossing of VIL(ac)max. If the actual signal is always earlier than the nominal slew rate line between

shaded ‘VREF(dc) to AC region’, use nominal slew rate for derating value. See Figure 24 Illustration of nominal slew rate for

tDS (differential DQS, DQS ).

If the actual signal is later than the nominal slew rate line anywhere between shaded ‘VREF(dc) to AC region’, the slew rate of a

tangent line to the actual signal from the AC level to DC level is used for derating value. See Figure 25 Illustration of tangent line

for tDS (differential DQS, DQS ).

Hold (tDH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(dc)max and the first

crossing of VREF(dc). Hold (tDH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of

VIH(dc)min and the first crossing of VREF(dc). If the actual signal is always later than the nominal slew rate line between

shaded ‘DC level to VREF(dc) region’, use nominal slew rate for derating value. See Figure 26 Illustration of nominal slew rate

for tDH (differential DQS, DQS ).

If the actual signal is earlier than the nominal slew rate line anywhere between shaded ‘DC to VREF(dc) region’, the slew rate of

a tangent line to the actual signal from the DC level to VREF(dc) level is used for derating value. See Figure 27 Illustration of

tangent line for tDH (differential DQS, DQS ).

Although for slow slew rates the total setup time might be negative (i.e. a valid input signal will not have reached VIH/IL(ac) at

the time of the rising clock transition) a valid input signal is still required to complete the transition and reach VIH/IL(ac).

For slew rates in between the values listed in above DDR2-667, DDR2-800 and DDR2-1066 tDS/tDH derating with differential

data strobe table, the derating values may be obtained by linear interpolation.

These values are typically not subject to production test. They are verified by design and characterization.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 61 - Revision A01

tDS tDH tDS tDH

nominal

slew rate

nominal

slew rate

VREF to AC

region

VDDQ

VIH(ac)min

VIH(dc)min

VREF(dc)

VIL(dc)max

VIL(ac)max

VSS

ΔTF ΔTR

Setup Slew Rate

Falling Signal =VREF(dc) -V

IL(ac)max Setup Slew Rate

Rising Signal =VIH(ac)min -V

REF(dc)

VREF to AC

region

DQS

ΔTR

ΔTF

Figure 24 —Illustration of nominal slew rate for tDS (differential DQS, DQS )

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 62 - Revision A01

DQS

tDS tDH tDS tDH

tangent

line

tangent

line

VREF to AC

region

VDDQ

VIH(ac)min

VIH(dc)min

VREF(dc)

VIL(dc)max

VIL(ac)max

VSS

ΔTF

ΔTR

Setup Slew Rate

Falling Signal =tangent line[VREF(dc) -V

IL(ac)max]

VREF to AC

region

nominal

line

Setup Slew Rate

Rising Signal =tangent line[VIH(ac)min -V

REF(dc)]

nominal

line

ΔTF

ΔTR

Figure 25 —Illustration of tangent line for tDS (differential DQS, DQS )

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 63 - Revision A01

DQS

tDS tDH tDS tDH

nominal

slew rate

nominal

slew rate

DC to VREF

region

VDDQ

VIH(ac)min

VIH(dc)min

VREF(dc)

VIL(dc)max

VIL(ac)max

VSS

ΔTFΔTR

Hold Slew Rate

Rising Signal =VREF(dc) -V

IL(dc)max Hold Slew Rate

Falling Signal =VIH(dc)min -V

REF(dc)

DC to VREF

region

ΔTR ΔTF

Figure 26 —Illustration of nominal slew rate for tDH (differential DQS,DQS )

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 64 - Revision A01

DQS

tDS tDH tDS tDH

tangent

line

DC to VREF

region

VDDQ

VIH(ac)min

VIH(dc)min

VREF(dc)

VIL(dc)max

VIL(ac)max

VSS

ΔTFΔTR

DC to VREF

region

nominal

line

tangent

line

nominal

line

Hold Slew Rate

Rising Signal =

tangent line[VREF(dc) -V

IL(ac)max]

Hold Slew Rate

Falling Signal =

tangent line [VIH(dc)min -V

REF(dc)]

ΔTF

ΔTR

Figure 27 —Illustration tangent line for tDH (differential DQS,DQS )

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 65 - Revision A01

9.12 AC Input Test Conditions

(0℃ ≤ TCASE ≤ 85℃ for -18/-25/-3, -40℃ ≤ TCASE ≤ 95℃ for 25I/25A, VDD, VDDQ = 1.8V ± 0.1V)

CONDITION SYMBOL VALUE UNIT NOTES

Input reference voltage VREF 0.5 x VDDQ V 1

Input signal maximum peak to peak swing VSWING(MAX) 1.0 V 1

Input signal minimum slew rate SLEW 1.0 V/nS 2, 3

Notes:

1. Input waveform timing is referenced to the input signal crossing through the VIH/IL(ac) level applied to the device under test.

2. The input signal minimum slew rate is to be maintained over the range from VREF to VIH(ac) min for rising edges and the

range from VREF to VIL(ac) max for falling edges as shown in the below figure.

3. AC timings are referenced with input waveforms switching from VIL(ac) to VIH(ac) on the positive transitions and VIH(ac) to

VIL(ac) on the negative transitions.

9.13 Differential Input/Output AC Logic Levels

(0℃ ≤ TCASE ≤ 85℃ for -18/-25/-3, -40℃ ≤ TCASE ≤ 95℃ for 25I/25A, VDD, VDDQ = 1.8V ± 0.1V)

PARAMETER SYM. MIN. MAX. UNIT NOTES

AC differential input voltage VID (ac) 0.5 VDDQ + 0.6

V 1

AC differential cross point input voltage VIX (ac) 0.5 x VDDQ - 0.175 0.5 x VDDQ + 0.175 V 2

AC differential cross point output voltage VOX (ac) 0.5 x VDDQ - 0.125 0.5 x VDDQ + 0.125 V 3

Notes:

1. VID (ac) specifies the input differential voltage |VTR -VCP | required for switching, where VTR is the true input signal (such

as CLK, LDQS or UDQS) and VCP is the complementary input signal (such as CLK , LDQS or UDQS ). The minimum

value is equal to VIH (ac) - VIL (ac).

2. The typical value of VIX (ac) is expected to be about 0.5 x VDDQ of the transmitting device and VIX (ac) is expected to track

variations in VDDQ. VIX (ac) indicates the voltage at which differential input signals must cross.

3. The typical value of VOX (ac) is expected to be about 0.5 x VDDQ of the transmitting device and VOX (ac) is expected to

track variations in VDDQ. VOX (ac) indicates the voltage at which differential output signals must cross.

△TF △TR

VDDQ

VIH(ac) min

Falling Slew = Rising Slew =

VIH(dc) min

VREF

VIL(dc) max

VIL(ac) max

VSS

VSWING(MAX)

VREF - VIL(ac) max

△TF

VIH(ac) min - VREF

△TR

VDDQ

VSSQ

VIX or VOX

VID

VTR

Crossing point

VCP

Figure 28—AC input test signal and Differential signal levels waveform

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 66 - Revision A01

9.14 AC Overshoot / Undershoot Specification

9.14.1 AC Overshoot / Undershoot Specification for Address and Control Pins:

Applies to A0-A12, BA0-BA1, /CS, /RAS, /CAS, /WE, CKE, ODT

PARAMETER −18 −25/25I/25A −3 UNIT

Maximum peak amplitude allowed for overshoot area 0.5 0.5 0.5 V

Maximum peak amplitude allowed for undershoot area 0.5 0.5 0.5 V

Maximum overshoot area above VDD 0.5 0.66 0.8 V-nS

Maximum undershoot area below VSS 0.5 0.66 0.8 V-nS

9.14.2 AC Overshoot / Undershoot Specification for Clock, Data, Strobe and Mask pins:

Applies to DQ, LDQS, /LDQS, UDQS, /UDQS, LDM, UDM, CLK, /CLK

PARAMETER −18 −25/25I/25A −3 UNIT

Maximum peak amplitude allowed for overshoot area 0.5 0.5 0.5 V

Maximum peak amplitude allowed for undershoot area 0.5 0.5 0.5 V

Maximum overshoot area above VDDQ 0.19 0.23 0.23 V-nS

Maximum undershoot area below VSSQ 0.19 0.23 0.23 V-nS

Maximum Amplitude

Overshoot Area

Undershoot Area

VDD/VDDQ

Volts (V)

Time (nS)

VSS/VSSQ

Figure 29—AC overshoot and undershoot definition

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 67 - Revision A01

10. TIMING WAVEFORMS

10.1 Command Input Timing

CLK

tCK

tCLtCH

tIS tIH

RAS

CAS

A0~A12

BA0,1

Refer to the Command Truth Table

10.2 Timing of the CLK Signals

IH(AC)

IL(AC)

CLK

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 68 - Revision A01

10.3 ODT Timing for Active/Standby Mode

10.4 ODT Timing for Power Down Mode

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 69 - Revision A01

10.5 ODT Timing mode switch at entering power down mode

CLK

T-5 T0

CKE

RTT

tAONPD(max)

tAOND

tAOFPD(max)

tAOFD

tANPD

tIS

CLK

Entering Slow Exit Active Power Down

Mode or Precharge Power Down Mode

tIS

T-4 T-3 T-2 T-1 T1 T2

VIL(ac)

VIH(ac)

ODT

Internal

Term Res.

Internal

Term Res.

Internal

Term Res.

Internal

Term Res.

Active & Standby

mode timings to be

applied

Active & Standby

mode timings to be

applied

Power Down mode

timings to be applied

Power Down mode

timings to be applied

RTT

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 70 - Revision A01

10.6 ODT Timing mode switch at exiting power down mode

CLK

T0 T7 T8 T9 T10

CKE

RTT

ODT

Active & Standby mode

timings to be applied

Power Down mode

timings to be applied

tIS

CLK

Internal

Term Res.

tAXPD

Exiting from Slow Active Power Down Mode

or Precharge Power Down Mode

T1 T5 T6

tIS

tAOFD

tAOFPD(max)

tAONPD(max)

tAOND

VIL(ac)

VIH(ac)

Internal

Term Res.

Internal

Term Res.

Internal

Term Res.

ODT

Active & Standby mode

timings to be applied

Power Down mode

timings to be applied

VIH(ac)

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 71 - Revision A01

10.7 Data output (read) timing

CLK

DQS

tDQSmax tDQSmax

tQH

tRPST

tCLtCH

QQ Q

CLK

DQS

tQH

tRPRE

DQS

10.8 Burst read operation: RL=5 (AL=2, CL=3, BL=4)

NOP

NOPNOP

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

DQ's

NOP NOP NOP NOP

Dout

RL = 5

CL = 3

≤ tDQSCK

NOP

Dout

AL = 2

Posted CAS

READ A NOP NOP NOP NOP NOP NOP NOP NOP

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 72 - Revision A01

10.9 Data input (write) timing

VIH(ac)

VIL(ac)

DDDD

VIH(dc)

VIL(dc)

VIH(dc)

VIL(dc)

DMin

tDS

VIH(ac)

VIL(ac)

tWPRE

tDQSH tDQSL

DQS

tWPST

tDS tDH tDH

DMin

DQS

10.10 Burst write operation: RL=5 (AL=2, CL=3, WL=4, BL=4)

T0 T1 T2 T3 T4 T5 T6 T7 Tn

DIN

tDQSS tDQSS

tDSS

Completion of

The Burst Write

NOP NOPNOPNOPNOPNOPNOP

Posted CAS

WRITE A

tDQSS

tDSH

tDQSS

≥ tWR

Precharge

CLK

CMD

DQS

DQs

Case 1: with tDQSS(max)

Case 2: with tDQSS(min)

WL = RL 1= 4

tDSH

DQS

CLK

DQS

≥ tWR

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 73 - Revision A01

10.11 Seamless burst read operation: RL = 5 ( AL = 2, and CL = 3, BL = 4)

T0 T1 T2 T5T3 T6T4 T7 T8

Post CAS

READ A

Post CAS

READ B

NOP NOP NOP NOP NOP NOP NOP

DOUT

CLK

CMD

DQS

DQ's

AL = 2 CL = 3

RL = 5

Note:

The seamless burst read operation is supported by enabling a read command at every other clock for BL = 4 operation, and

every 4 clock for BL = 8 operation. This operation is allowed regardless of same or different banks as long as the banks are

activated.

10.12 Seamless burst write operation: RL = 5 ( WL = 4, BL = 4)

T0 T1 T2 T5

T3 T6

T4 T7 T8

Post CAS

Write A

Post CAS

Write B

NOP NOP NOP NOP NOP NOP NOP

DIN

CLK

CMD

DQS

DQ's DIN

WL = RL - 1 = 4

Note:

The seamless burst write operation is supported by enabling a write command every other clock for BL = 4 operation, every four

clocks for BL = 8 operation. This operation is allowed regardless of same or different banks as long as the banks are activated.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 74 - Revision A01

10.13 Burst read interrupt timing: RL =3 (CL=3, AL=0, BL=8)

NOPNOPNOPNOP

READ A

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

NOP

Dout

READ B NOP

NOP

DQ's

10.14 Burst write interrupt timing: RL=3 (CL=3, AL=0, WL=2, BL=8)

Write A NOPNOPWrite BNOP

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

NOPNOP NOPNOP

Din

DQ's

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 75 - Revision A01

10.15 Write operation with Data Mask: WL=3, AL=0, BL=4)

DQS/

DQS

VIH(ac) VIH(dc)

tDS tDH tDS tDH

WL + tDQSS (max)

tWR

WL + tDQSS (min)

Write

CLK

CMDMAND

DQS/DQS

Case 1: min tDQSS

Case 2: max tDQSS

CLK

DQS/DQS

VIL(dc)

VIL(ac)

VIH(ac)

VIL(ac)

VIH(dc)

VIL(dc)

Data Mask Timing

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 76 - Revision A01

10.16 Burst read operation followed by precharge: RL=4 (AL=1, CL=3, BL=4, tRTP

≤ 2clks)

Precharge NOP Bank A

Activate

NOPNOPNOP

Post CAS

READ A NOP

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

≥ tRAS

≥ tRTP

AL+BL/2 clks ≥ tRP

AL = 1 CL = 3

RL = 4

NOP

Dout

DQ's

10.17 Burst read operation followed by precharge: RL=4 (AL=1, CL=3, BL=8, tRTP

≤ 2clks)

NOP Precharge NOP NOPNOPNOPNOPNOP

Post CAS

READ A

T0 T1 T2 T3 T4 T5 T6 T7 T8

≥ tRTP

AL + BL/2 clks

AL = 1 CL = 3

RL = 4 Dout

Dout

first 4-bit prefetch second 4-bit prefetch

CLK/CLK

CMD

DQS,

DQS

DQ's

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 77 - Revision A01

10.18 Burst read operation followed by precharge: RL=5 (AL=2, CL=3, BL=4, tRTP

≤ 2clks)

10.19 Burst read operation followed by precharge: RL=6 (AL=2, CL=4, BL=4, tRTP

≤ 2clks)

Dout

NOP

NOPNOP

Precharge

NOPNOPNOP

Post CAS

READA

Bank A

Activate

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

DQ's

≥ tRAS

≥ tRTP

AL + BL/2 clks ≥ tRP

AL = 2 CL = 4

RL = 6

CL = 4

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 78 - Revision A01

10.20 Burst read operation followed by precharge: RL=4 (AL=0, CL=4, BL=8, tRTP

> 2clks)

10.21 Burst write operation followed by precharge: WL = (RL-1) = 3

NOPNOPNOPNOPNOPNOPNOP

Post CAS

WRITE A Precharge

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

DQ's

WL = 3

Completion of the Burst Write

DIN

≥ tWR

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 79 - Revision A01

10.22 Burst write operation followed by precharge: WL = (RL-1) = 4

10.23 Burst read operation with Auto-precharge: RL=4 (AL=1, CL=3, BL=8, tRTP ≤

2clks)

NOP NOP NOP Bank A

Activate

NOPNOPNOPNOP

Post CAS

READA

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

DQ's

≥ tRTP

AL + BL/2 clks ≥ tRP

AL = 1 CL = 3

RL = 4

Dout

first 4-bit prefetch second 4-bit prefetch

tRTP Precharge begins here

A10 = 1

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 80 - Revision A01

10.24 Burst read operation with Auto-precharge: RL=4 (AL=1, CL=3, BL=4, tRTP >

2clks)

NOP NOP Bank A

Activate

NOPNOPNOP

Post CAS

READA NOP

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

tRTP

≥ AL + tRTP + tRP

AL = 1 CL = 3

RL = 4

NOP

Dout

DQ's

4-bit prefetch

Precharge begins here

tRP

A10 = 1

10.25 Burst read with Auto-precharge followed by an activation to the same bank

(tRC Limit): RL=5 (AL=2, CL=3, internal tRCD=3, BL=4, tRTP ≤ 2clks)

NOP NOP NOPNOPNOPNOP

Post CAS

READA

Bank A

Activate

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

≥tRAS min. (AL + BL/2)

AL = 2 CL = 3

RL = 5

NOP

Dout

DQ's

Auto-precharge begins

A10 = 1

≥ tRP

tRC min.

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 81 - Revision A01

10.26 Burst read with Auto-precharge followed by an activation to the same bank

(tRP Limit): RL=5 (AL=2, CL=3, internal tRCD=3, BL=4, tRTP ≤ 2clks)

NOP NOP NOP

NOPNOPNOP

Post CAS

READA

Bank A

Activate

T0 T1 T2 T3 T4 T5 T6 T7

CLK/CLK

CMD

DQS,

DQS

≥tRAS min.

AL = 2 CL = 3

RL = 5

NOP

Dout

DQ's

Auto-precharge begins

A10 = 1

tRP min.

≥ tRC

10.27 Burst write with Auto-precharge (tRC Limit): WL=2, WR=2, BL=4, tRP=3

tRC min.

WL= RL- 1 = 2

≥ WR ≥ tRP

NOPNOPNOPNOPNOPNOPNOP

Post CAS

WRA Bank A

Bank A

Activate

T0 T1 T2 T3 T4 T5 T6 T7

Auto-precharge Begins

A10 = 1

CLK/CLK

CMD

DQS,

DQS

DQ's

Completion of the Burst Write

DIN

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 82 - Revision A01

10.28 Burst write with Auto-precharge (WR + tRP Limit): WL=4, WR=2, BL=4, tRP=3

10.29 Self Refresh Timing

T0 T1 T2 T3 T4 T5 T6 Tm Tn

Self

Refresh NOP Non-Read

Command NOP

≥tXSNR

≥ tXSRD

tIH

tIS

tIH

tIHtIS

tIS

tRP

tIS

tAOFD

tCK

tCH tCL

VIL(ac)

VIH(ac)

VIL(ac)

VIH(ac)

VIL(dc)

VIH(dc)

CLK

CMD

CKE

ODT

CLK

VIL(ac)

Read

Command

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 83 - Revision A01

10.30 Active Power Down Mode Entry and Exit Timing

CLK

T0 T1 T2 Tn Tn+1 Tn+2

Valid

Command

NOP

NOPNOPNOPActivate

tXARD or

tXARDS

Active

Power Down

Exit

Active

Power Down

Entry

tIS

CKE

CMD

tIS

10.31 Precharged Power Down Mode Entry and Exit Timing

CLK

CMD

T0 T1 T2 T3 Tn

CKE

Tn+1 Tn+2

NOP NOP

tIS

tRP

Precharge

Power Down

Entry

Precharge

Power Down

Exit

tXP

tIS

NOPNOP

NOP

NOPPrecharge Valid

Command

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 84 - Revision A01

10.32 Clock frequency change in precharge Power Down mode

NOP NOP NOP NOP NOP Valid

T0 T1 T2 T4 TXTX+1 TYTY+1 TY+2 TY+3 TY+4 Tz

CLK

tIS

DLL

RESET

Minimum 2 clocks

required before

changing frequency Stable new clock

before power down exit

Frequency change

Occurs here

200 Clocks

ODT is off during

DLL RESET

CLK

CMD

CKE

ODT

tIS

tIH tRP

tAOFD

tXP

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 85 - Revision A01

11. PACKAGE SPECIFICATION

Package Outline WBGA-84 (8x12.5 mm2)

84xψb

A1 A

SEATING PLANE

SYMBOL DIMENSION (MM)

MIN. NOM. MAX.

aaa

bbb

ccc

--- ---

--- --- 0.10

0.20

--- --- 0.15

0.80 BSC.

6.40 BSC.

11.20 BSC.

1.20

0.40

0.50

12.60

8.10

8.00

12.50

7.90

12.40

0.40

0.25

23789

---

------

ccc

aaa

bbb

PIN A1 INDEX PIN A1 INDEX

Ball Land

Ball Opening

Note: 1. Ball land : 0.5mm

2. Ball opening : 0.4mm

3. PCB Ball land suggested 0.4mm

SOLDER BALL DIAMETER REFERS.

TO POST REFLOW CONDITION.

THE WINDOW-SIDE

ENCAPSULANT

W9725G6JB

Publication Release Date: Mar. 10, 2010

- 86 - Revision A01

12. REVISION HISTORY

VERSION DATE PAGE DESCRIPTION

A01 Mar. 10, 2010 All Initial formal data sheet

Important Notice

Winbond products are not designed, intended, authorized or warranted for use as components

in systems or equipment intended for surgical implantation, atomic energy control

instruments, airplane or spaceship instruments, transportation instruments, traffic signal

instruments, combustion control instruments, or for other applications intended to support or

sustain life. Further more, Winbond products are not intended for applications wherein failure

of Winbond products could result or lead to a situation wherein personal injury, death or

severe property or environmental damage could occur.

Winbond customers using or selling these products for use in such applications do so at their

own risk and agree to fully indemnify Winbond for any damages resulting from such improper

use or sales.