AUIRFZ44V
HEXFET® Power MOSFET
11/1/11
www.irf.com 1
S
D
G
Features
lAdvanced Planar Technology
lLow On-Resistance
lDynamic dV/dT Rating
l175°C Operating Temperature
lFast Switching
lFully Avalanche Rated
lRepetitive Avalanche Allowed up to Tjmax
lLead-Free, RoHS Compliant
lAutomotive Qualified *
Specifically designed for Automotive applications, this
stripe planar design of HEXFET® Power MOSFETs
utilizes the latest processing techniques to achieve low
on-resistance per silicon area. This benefit combined with
the fast switching speed and ruggedized device design
that HEXFET power MOSFETs are well known for,
provides the designer with an extremely efficient and
reliable device for use in Automotive and a wide variety
of other applications.
Description
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These
are stress ratings only; and functional operation of the device at these or any other condition beyond those indicated
in the specifications is not implied.Exposure to absolute-maximum-rated conditions for extended periods may affect
device reliability. The thermal resistance and power dissipation ratings are measured under board mounted and still
air conditions. Ambient temperature (TA) is 25°C, unless otherwise specified.
GDS
Gate Drain Source
TO-220AB
AUIRFZ44V
D
S
D
G
V
(BR)DSS
60V
R
DS(on)
max. 16.5mΩ
I
D
55A
AUTOMOTIVE GRADE
Parameter
Units
I
D
@ T
C
= 25°C Continuous Drain Current, V
GS
@ 10V
I
D
@ T
C
= 100°C Continuous Drain Current, V
GS
@ 10V A
I
DM
Pulsed Drain Current
c
P
D
@T
C
= 25°C Power Dissipation
Linear Derating Factor W/°C
V
GS
Gate-to-Source Voltage V
E
AS
Single Pulse Avalanche Energy
d
mJ
I
AR
Avalanche Current
c
A
E
AR
Repetitive Avalanche Energy
c
mJ
dv/dt Peak Diode Recovery dv/dt
e
V/ns
T
J
Operating Junction and
T
STG
Storage Temperature Range °C
Soldering Temperature, for 10 seconds
Mounting Torque, 6-32 or M3 screw
Thermal Resistance
Parameter Typ. Max. Units
R
θ
Junction-to-Case ––– 1.3
R
θ
CS
Case-to-Sink, Flat, Greased Surface 0.50 –––
R
θ
JA
Junction-to-Ambient (PCB mounted) ––– 62
55
11
10 lbf
y
in (1.1N
y
m)
-55 to + 175
°C/W
300 (1.6mm from case )
0.77
±20
4.5
W
115
115
Max.
55
39
220
HEXFET® is a registered trademark of International Rectifier.
*Qualification standards can be found at http://www.irf.com/
PD - 96415
AUIRFZ44V
2www.irf.com
S
D
G
S
D
G
Repetitive rating; pulse width limited by max. junction temperature. ( See fig. 11 )
Starting TJ = 25°C, L = 89μH, RG = 25Ω, IAS = 51A. (See Figure 12)
ISD 51A, di/dt 227A/μs, VDD V(BR)DSS, TJ 175°C
Pulse width 300μs; duty cycle 2%.
Notes:
Static Electrical Characteristics @ T
J
= 25°C (unless otherwise specified)
Parameter Min. Typ. Max. Units
V
(BR)DSS Drain-to-Source Breakdown Voltage 60 ––– ––– V
Δ
V
(BR)DSS
/
Δ
T
J Breakdown Voltage Temp. Coefficient ––– 0.062 –– V/°C
RDS(on) Static Drain-to-Source On-Resistance –– –– 16.5
V
GS(th) Gate Threshold Voltage 2.0 ––– 4.0 V
gfs Forward Transconductance 24 ––– ––– S
I
DSS Drain-to-Source Leakage Current ––– –– 25 μA
––– ––– 250
I
GSS Gate-to-Source Forward Leakage ––– –– 100 nA
Gate-to-Source Reverse Leakage ––– –– -100
Dynamic Electrical Characteristics @ T
J
= 25°C (unless otherwise specified)
Q
gTotal Gate Charge ––– ––– 67
Q
gs Gate-to-Source Charge ––– –– 18 nC
Q
gd Gate-to-Drain ("Miller") Charge ––– ––– 25
t
d(on) Turn-On Delay Time ––– 13 –––
t
rRise Time –97–
t
d(off) Turn-Off Delay Time ––– 40 ––– ns
t
fFall Time ––– 57 –––
L
DInternal Drain Inductance Between lead,
nH 6mm (0.25in.)
L
SInternal Source Inductance Between lead,
and center of die contact
C
iss Input Capacitance ––– 1812 ––
C
oss Output Capacitance ––– 393 –––
C
rss Reverse Transfer Capacitance ––– 103 ––– ƒ = 1.0MHz, See Fig.5
Diode Characteristics
Parameter Min. Typ. Max. Units
I
S
Continuous Source Current
(Body Diode) A
I
SM
Pulsed Source Current
(Body Diode)
c
V
SD
Diode Forward Voltage ––– –– 2.5 V
t
rr
Reverse Recovery Time ––– 70 105 ns
Q
rr
Reverse Recovery Charge ––– 146 219 nC
t
on
Forward Turn-On Time
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
pF
––– MOSFET symbol
showing the
–––
–––
–––
55
220
––– ––
––––––
4.5
7.5
VGS = 10V, See Fig.6 and 13
f
VDD = 30V
ID = 51A
RG = 9.1Ω
T
J
= 25°C, I
S
= 51A, V
GS
= 0V
f
T
J
= 25°C, I
F
= 51A
di/dt = 100A/μs
f
Conditions
VGS = 0V, ID = 250μA
Reference to 25°C, ID = 1mA
VGS = 10V, ID = 31A
f
VDS = VGS, ID = 250μA
VDS = 60V, VGS = 0V
VDS = 48V, VGS = 0V, TJ = 150°C
integral reverse
p-n junction diode.
VDS = 25V, ID = 31A
f
ID = 51A
VDS = 48V
Conditions
RD = 0.6Ω, See Fig.10
f
VGS = 0V
VDS = 25V
VGS = 20V
VGS = -20V
mΩ
AUIRFZ44V
www.irf.com 3
Qualification Information
Moisture Sensitivity Level
3L-TO-220
N/A
Qualification Level
Automotive
(per AEC-Q101)
††
Comments: This part number(s) passed Automotive qualification.
IR’s Industrial and Consumer qualification level is granted by
extension of the higher Automotive level.
Charged Device Model Class C5(+/- 2000V )
†††
(per AEC-Q101-005)
RoHS Compliant Yes
ESD
Machine Model Class M3(+/- 400V )
†††
(per AEC-Q101-002)
Human Body Model Class H1B(+/- 1000V )
†††
(per AEC-Q101-001)
Qualification standards can be found at International Rectifier’s web site: http//www.irf.com/
Exceptions (if any) to AEC-Q101 requirements are noted in the qualification report.
††† Highest passing voltage
AUIRFZ44V
4www.irf.com
Fig 2. Typical Output Characteristics
Fig 1. Typical Output Characteristics
Fig 3. Typical Transfer Characteristics Fig 4. Normalized On-Resistance
Vs. Temperature
0.1
1
10
100
1000
0.1 1 10 100
20μs PULSE WIDTH
T = 25 C
J°
TOP
BOTTOM
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
V , Drain-to-Source Voltage (V)
I , Drain-to-Source Current (A)
DS
D
4.5V
1
10
100
1000
0.1 1 10 100
20μs PULSE WIDTH
T = 175 C
J°
TOP
BOTTOM
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
V , Drain-to-Source Voltage (V)
I , Drain-to-Source Current (A)
DS
D
4.5V
-60 -40 -20 020 40 60 80 100 120 140 160 180
0.0
0.5
1.0
1.5
2.0
2.5
3.0
T , Junction Temperature ( C)
R , Drain-to-Source On Resistance
(Normalized)
J
DS(on)
°
V =
I =
GS
D
10V
55A
1
10
100
1000
45678910 11 12
V = 25V
20μs PULSE WIDTH
DS
V , Gate-to-Source Voltage (V)
I , Drain-to-Source Current (A)
GS
D
T = 25 C
J°
T = 175 C
J°
AUIRFZ44V
www.irf.com 5
Fig 7. Typical Source-Drain Diode
Forward Voltage
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
Fig 8. Maximum Safe Operating Area
110 100
VDS, Drain-to-Source Voltage (V)
0
1000
2000
3000
4000
C, Capacitance(pF)
Coss
Crss
Ciss
VGS = 0V, f = 1 MHZ
Cis = Cgs + Cgd, Cds SHORTED
Crss = Cgd
Coss = Cds + Cgd
020 40 60 80 100
0
4
8
12
16
20
Q , Total Gate Charge (nC)
V , Gate-to-Source Voltage (V)
G
GS
I =
D51A
V = 12V
DS
V = 30V
DS
V = 48V
DS
1
10
100
1000
1 10 100 1000
OPERATION IN THIS AREA LIMITED
BY RDS(on)
Single Pulse
T
T
= 175 C
= 25 C
°
°
J
C
V , Drain-to-Source Voltage (V)
I , Drain Current (A)I , Drain Current (A)
DS
D
10us
100us
1ms
10ms
0.1
1
10
100
1000
0.2 0.7 1.2 1.7 2.2
V ,Source-to-Drain Voltage (V)
I , Reverse Drain Current (A)
SD
SD
V = 0 V
GS
T = 25 C
J°
T = 175 C
J°
AUIRFZ44V
6www.irf.com
25 50 75 100 125 150 175
0
10
20
30
40
50
60
T , Case Temperature ( C)
I , Drain Current (A)
°
C
D
Fig 9. Maximum Drain Current Vs.
Case Temperature
Fig 10a. Switching Time Test Circuit
VDS
90%
10%
VGS
t
d(on)
t
r
t
d(off)
t
f
Fig 10b. Switching Time Waveforms
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
0.01
0.1
1
10
0.00001 0.0001 0.001 0.01 0.1 1
Notes:
1. Duty factor D = t / t
2. Peak T = P x Z + T
1 2
JDM thJC C
P
t
t
DM
1
2
t , Rectangular Pulse Duration (sec)
Thermal Response(Z )
1
thJC
0.01
0.02
0.05
0.10
0.20
D = 0.50
SINGLE PULSE
(THERMAL RESPONSE)
RD
VDS
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
VGS
RG
D.U.T.
10V
+
-
VDS
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
VGS
RG
D.U.T.
10V
VDD
AUIRFZ44V
www.irf.com 7
D.U.T. V
DS
I
D
I
G
3mA
V
GS
.3μF
50KΩ
.2μF
12V
Current Regulator
Same Type as D.U.T.
Current Sampling Resistors
+
-
Fig 13b. Gate Charge Test Circuit
Fig 13a. Basic Gate Charge Waveform
Fig 12b. Unclamped Inductive Waveforms
Fig 12a. Unclamped Inductive Test Circuit
tp
V
(BR)DSS
I
AS
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
R
G
I
AS
0.01
Ω
t
p
D.U.T
L
VDS
+
-V
DD
DRIVER
A
15V
20V
25 50 75 100 125 150 175
0
50
100
150
200
250
Starting T , Junction Temperature ( C)
E , Single Pulse Avalanche Energy (mJ)
J
AS
°
ID
TOP
BOTTOM
21A
36A
51A
Q
G
Q
GS
Q
GD
V
G
Charge
10 V
AUIRFZ44V
8www.irf.com
Fig 14. For N-Channel HEXFETS
Peak Diode Recovery dv/dt Test Circuit
+
-
+
+
+
-
-
-
RG
VDD
dv/dt controlled by RG
Driver same type as D.U.T.
ISD controlled by Duty Factor "D"
D.U.T. - Device Under Test
D.U.T Circuit Layout Considerations
Low Stray Inductance
Ground Plane
Low Leakage Inductance
Current Transformer
P.W. Period
di/dt
Diode Recovery
dv/dt
Ripple 5%
Body Diode Forward Drop
Re-Applied
Voltage
Reverse
Recovery
Current
Body Diode Forward
Current
VGS=10V
VDD
ISD
Driver Gate Drive
D.U.T. ISD Waveform
D.U.T. VDS Waveform
Inductor Curent
D = P. W .
Period
* V
GS = 5V for Logic Level Devices
*
AUIRFZ44V
www.irf.com 9
TO-220AB Package Outline
Dimensions are shown in millimeters (inches)
TO-220AB Part Marking Information
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
YWWA
XX or XX
Part Number
IR Logo
Lot Code
AUFZ44V
Date Code
Y= Year
WW= Work Week
A= Automotive, Lead Free
AUIRFZ44V
10 www.irf.com
Ordering Information
Base part Package Type Standard Pack Complete Part Number
Form Quantity
AUIRFZ44V TO-220 Tube 50 AUIRFZ44V
AUIRFZ44V
www.irf.com 11
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR)
reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products
and services at any time and to discontinue any product or services without notice. Part numbers designated with the
“AU” prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance
and process change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time
of order acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance
with IR’s standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary
to support this warranty. Except where mandated by government requirements, testing of all parameters of each
product is not necessarily performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their
products and applications using IR components. To minimize the risks with customer products and applications,
customers should provide adequate design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information
with alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that
product or service voids all express and any implied warranties for the associated IR product or service and is an
unfair and deceptive business practice. IR is not responsible or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant
into the body, or in other applications intended to support or sustain life, or in any other application in which the failure
of the IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR
products for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the
design or manufacture of the product.
Only products certified as military grade by the Defense Logistics Agency (DLA) of the US Department of Defense,
are designed and manufactured to meet DLA military specifications required by certain military, aerospace or other
applications. Buyers acknowledge and agree that any use of IR products not certified by DLA as military-grade, in
applications requiring military grade products, is solely at the Buyer’s own risk and that they are solely responsible for
compliance with all legal and regulatory requirements in connection with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific
IR products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the
designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive
applications, IR will not be responsible for any failure to meet such requirements.
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
101 N. Sepulveda Blvd., El Segundo, California 90245
Tel: (310) 252-7105
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
International Rectifier:
AUIRFZ44V