FEATURES BENEFITS
HOW TO ORDER
MLT S
ERIES
SMALL
DIAMETER
LINEAR
POSITION
TRANSDUCER
Electrical
Travel*
Unit of
Measure
Termination
Shaft
Linearity
Note: Not all combinations are available. Minimum quantity orders apply. Contact the factory for more details.
* Note: The Electrical Travel correlates to the Total Resistance (Ohms).
MLT 0R5 N 0750 F 5 C
Model
N = Inches
5 = 4-40 Thread
C = Cable
B =0.1%
F = 1.0% (Best possible on 0.5 in. device)
D =0.25% (Best possible on 1.0 in. device)
APPLICATIONS
•
MEDICAL EQUIPMENT
•
HOSPITAL BEDS
•
LINEAR ACTUATORS
•
ANIMATED
CHARACTERS
•
GAUGING
•
WOODWORKING
GUIDES
•
FLUID FLOW METERS
•
SEISMOLOGY
•
SEMI CONDUCTOR
PROCESSING
• 0.375 inch diameter • Fits into tight spaces, clamps easily to cylinders
• Dual wiper design • Improves shock and vibration performance
• Extruded wiper block guides • Smooth quiet motion; extends operating life
• MystR® plastic element • Tested up to one billion operations
• Internal spring loaded ball joint • Less error from shaft misalignment
• Anodized extruded aluminum housing • Tolerates clamping loads
• Stainless steel shaft • Full performance in hostile environments
• Precious metal contact • Low noise level over entire life
• Absolute continuous measurement • Accurate position at power up
MLT • 3/8 INCH DIAMETER LINEAR POSITION TRANSDUCER
The Models MLT are small diameter linear position transducers rugged
enough to withstand the hostile environment of the factory. Using a
proprietary dual wiper, internal ball joint and the MystR® conductive plastic
film the MLT provides usable output at high vibration levels for long periods.
MLT Transducers use precious metal wipers to further enhance reliability.
Intrinsically Safe for Class I, II, and III Division 1, Groups A, B, C, D,
E, F and G for Hazardous (indoor/outdoor) NEMA 4 locations. V max
= 30 V, I max = 100 mA, Ci = 0, uF, Li, = 0 mH.
Total
Resistance* 0750, 1500, 3000, 4500, 6000, 7500, 9000
0R5 = 750
001 = 1500
002 = 3000
003 = 4500
004 = 6000
005 = 7500
006 = 9000
www.honeywell.com/sensing/products/di
MLT S
ERIES
•
SMALL
DIAMETER
LINEAR
POSITION
TRANSDUCER
TECHNICAL SPECIFICATIONS
Sensing and Control
Honeywell
100 Discovery W ay
Acton, MA 01720 USA
T el: (877) 384-1300; Fax: (978) 263-0630
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local
sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell
will repair or replace without charge those items it finds defective. The foregoing is Buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of merchantability and fitness for a particular purpose.
Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer
to determine the suitability of the product in the application.
Item # 1124900 M.G. 10/01 Rev. A
DIMENSIONS
xx.xx = inches
(xx.x) = mm
MECHANICAL
Total Mechanical Travel 0.55 to 6.05 in. (min)
13.9 to 153.7 mm (min)
Starting Force 1.0 oz (max)
Shock 50 g 11 ms half sine
Vibration 20 g rms 5 Hz to 2 KHz
Life One Billion dither operations
ELECTRICAL
Theoretical Electrical 0.5 to 6 in.
Travel (1 inch increments) (12.7 to 152.4 mm)
Independent Linearity See How to Order
Total Resistance 1500 Ohms per inch
electrical travel
Resistance Tolerance ±20%
Operating Temperature -40° to 80°C
(-40° to 176°F)
Resolution Infinite
Insulation Resistance 500 M Ohms @ 500 Vdc
Dielectric Strength 1000 V rms
Max. Applied Voltage 30 Vdc
Backlash 0.0005 in. max
Recommended Wiper Current <1 µA
Caution: Do not test on an Ohm Meter on the Rx 1 scale or other current devices.
Caution: Excessive Wiper Current can cause Output errors or damage.
Caution: Zero shaft side load is recommended to achieve maximum life.
(Retracted)
#4-40 UNC-2A
Thd x .50 [12.7] long
3/4"
[19.05]
1/8" x .063
[4.75 x 1.6]
1/8"
[3.18]
3/8"
[9.53]
3 - conductor cable
#26 AWG [65/44] 12.0 [305] long min.
(color coded per schematic)
(Electrical Travel +1.2 [30.48])
(Red)
V-in
Shaft
Extended
(Black)
Ground
(Orange)
V-out
Connect to High Impedance Circuit
Housing length 'X'
SPECIALS AND ACCESSORIES
• Other Mechanical Travels
• Other Electrical Travels
• Other Resistance Values
• Rod-end bearing
• Metric Shaft Adapter
Model Electrical Travel Total Resistance Housing Length Weight
in inches Ohms ‘X’ in inches in grams
MLT0R5 0.5 750 1.7 11
MLT001 1.0 1500 2.2 14
MLT002 2.0 3000 3.2 20
MLT003 3.0 4500 4.2 23
MLT004 4.0 6000 5.2 28
MLT005 5.0 7500 6.2 30
MLT006 6.0 9000 7.2 31
