Products and specifications discussed herein are subject to change by Micron without notice.
256Mb: x4, x8, x16 DDR SDRAM
Features
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D1.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 1©2003 Micron Technology, Inc. All rights reserved.
Double Data Rate (DDR) SDRAM
MT46V64M4 – 16 Meg x 4 x 4 banks
MT46V32M8 – 8 Meg x 8 x 4 banks
MT46V16M16 – 4 Meg x 16 x 4 banks
Features
•V
DD = 2.5V ±0.2V; VDDQ = 2.5V ±0.2V
VDD = 2.6V ±0.1V; VDDQ = 2.6V ±0.1V (DDR400)1
Bidirectional data strobe (DQS) transmitted/
received with data, that is, source-synchronous data
capture (x16 has two – one per byte)
Internal, pi pelined double data rate (DDR)
architecture; two data accesses per clock cycle
Differential clock inputs (CK and CK#)
Commands entered on each positive CK edge
DQS edge-aligned with data for READs; center-
aligned with data for WRITEs
DLL to align DQ and DQS transitions with CK
Four internal banks for concurrent operation
Data mask (DM) for masking write data
(x16 has two – one per by te)
Programmable burst lengths (BL): 2, 4, or 8
•Auto refresh
64ms, 8192-cycle
Longer-lead TSOP for improved reliability (OCPL)
2.5V I/O (SSTL_2-compatible)
Concurrent auto precharge option supported
tRAS lockout supported (tRAP = tRCD)
Notes: 1. DDR400 devices operating at < DDR333
conditions can use VDD/VDDQ = 2.5V +0.2V.
2. Available only on Revision K.
3. Available only on Revision M.
4. Not recommended for new designs.
Options Marking
Configuration
64 Meg x 4 (16 Meg x 4 x 4 banks) 64M4
32 Meg x 8 (8 Meg x 8 x 4 banks) 32M8
16 Meg x 16 (4 M eg x 16 x 4 banks) 16M16
•Plastic package OCPL
66-pin TSOP TG
66-pin TSOP (Pb-free) P
•Plastic package
60-ball FBGA (8mm x 12.5mm) CV
60-ball FBGA (8mm x 12.5mm)
(Pb-free) CY
Timing – cycle time
5ns @ CL = 3 (DDR400) -5B
6ns @ CL = 2.5 (DDR333) FBGA only -62
6ns @ CL = 2.5 (DDR333) TSOP only -6T2
Self refresh
Standard None
Low-power self refresh L
Tempe ratu re rati ng
Commercial (0C to +70C) None
Industrial (–40C to +85C) IT
Revision
x4, x8, x16 :K4
x4, x8, x16 :M
Table 1: Key Timing Parameters
CL = CAS (READ) latency; MIN clock rate with 50% duty cycle at CL = 2 (-75E, -75Z), CL = 2.5 (-6, -6T, -75), and
CL = 3 (-5B)
Speed Grade
Clock Rate (MHz)
Data-Out Window Access
Window DQS–DQ
SkewCL = 2 CL = 2.5 CL = 3
-5B 133 167 200 1.6ns ±0.70ns 0.40ns
-6 133 167 n/a 2.1ns ±0.70ns 0.40ns
6T 133 167 n/a 2.0ns ±0.70ns 0.45ns
-75E/-75Z 133 133 n/a 2.5ns ±0.75ns 0.50ns
-75 100 133 n/a 2.5ns ±0.75ns 0.50ns
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D1.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 2©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Features
Notes: 1. The -5B device is backward compat ible with all slower speed grades. The voltage range of
-5B device operating at slower speed grades is VDD = VDDQ = 2.5V ± 0.2V.
Figure 1: 256Mb DDR SDRAM Part Numbers
Table 2: Addressing
Parameter 64 Meg x 4 32 Meg x 8 16 Meg x 16
Configuration 16 Meg x 4 x 4 banks 8 Meg x 8 x 4 banks 4 Meg x 16 x 4 banks
Refresh count 8K 8K 8K
Row address 8K (A[12:0]) 8K (A[12:0]) 8K (A[12:0])
Bank address 4 (BA[1:0]) 4 (BA[1:0]) 4 (BA[1:0])
Column address 2K (A[9:0], A11) 1K (A[9:0]) 512 (A[8:0])
Table 3: Speed Grade Compatibility
Marking PC3200 (3-3-3) PC2700 (2.5-3-3) PC2100 (2-2-2) PC2100 (2-3-3) PC2100 (2.5-3-3) PC1600(2-2-2)
-5B1Yes Yes Yes Yes Yes Yes
-6 Yes Yes Yes Yes Yes
-6T Yes Yes Yes Yes Yes
-75E Yes Yes Yes Yes
-75Z Yes Yes Yes
-75 –––YesYes
-5B -6/-6T -75E -75Z -75 -75
Example Part Number: MT46V16M16P-6T:M
L
Special Options
Standard
Low power
Configuration
64 Meg x 4
32 Meg x 8
16 Meg x 16
64M4
32M8
16M16
Package
400-mil TSOP
400-mil TSOP (Pb-free)
TG
P
Speed Grade
tCK = 5ns, CL = 3
tCK = 6ns, CL = 2.5
tCK = 6ns, CL = 2.5
-5B
-6
-6T
IT
Operating Temp.
Commercial
Industrial
-
ConfigurationMT46V Package Speed
:
Revision
Sp.
Op. Temp.
Revision
x4, x8, x16
x4, x8, x16
:K
:M
8mm x 12.5mm FBGA
8mm x 12.5mm FBGA (Pb-free)
CV
CY
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D1.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 3©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Features
FBGA Part Marking System
Due to space limitations, FBGA-packaged components have an abbreviated part
marking that is differ ent from the part num ber. For a quick conversion of an FBGA code,
see the FBGA Part Marking Decoder on Microns Web site: www.micron.com.
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDRTOC.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 4©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Table of Contents
Table of Contents
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
State Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Functional Block Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Pin and Ball Assignments and Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Electrical Specifications – IDD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Electrical Specifications – DC and AC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
DESELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
NO OPERATION (NOP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
LOAD MODE REGISTER (LMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
ACTIVE (ACT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
READ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
WRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
PRECHARGE (PRE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
BURST TERMINATE (BST). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
AUTO REFRESH (AR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
SELF REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
INITIALIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
REGISTER DEFINITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
ACTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
READ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
WRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
AUTO REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
SELF REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Power-down (CKE Not Active) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDRLOF.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 5©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
List of Figur es
List of Figures
Figure 1: 256Mb DDR SDRAM Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Figure 2: Simplified State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 6: 66-Pin TSOP Pin Assignments (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Figure 9: 60-Ball FBGA (8mm x 12.5mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 10: Input Voltage Waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 11: SSTL_2 Clock Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Figure 12: Derating Data Valid Window (tQH – tDQSQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Figure 13: Full Drive Pull-Down Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Figure 14: Full Drive Pull-Up Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Figure 15: Reduced Drive Pull-Down Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Figure 16: Reduced Drive Pull-Up Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Figure 17: Activating a Specific Row in a Specific Bank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Figure 18: READ Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Figure 19: WRITE Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Figure 20: PRECHARGE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Figure 21: INITIALIZATION Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Figure 22: INITIALIZATION Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Figure 23: Mode Register D efinition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Figure 24: CAS Latency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Figure 25: Extended Mode Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Figure 26: Example: Meeting tRCD (tRRD) MIN When 2 < tRCD (tRRD) MIN/tCK 3. . . . . . . . . . . . . . . . . . . . . .60
Figure 29: Nonconsecutive READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Figure 30: Random READ Accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Figure 31: Terminating a READ Burst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Figure 32: READ-to-WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Figure 33: READ-to-PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Figure 34: Bank READ – Without Auto Precharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Figure 35: x4, x8 Data Output Timing – tDQSQ, tQH, and Data Valid Window . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Figure 36: x16 Data Output Timing – tDQSQ, tQH, and Data Valid Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Figure 37: Data Output Timing – tAC and tDQSCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Figure 38: WRITE Burst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Figure 39: Consecutive WRITE-to-WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Figure 41: Random WRITE Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Figure 42: WRITE-to-READ – Uninterrupting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Figure 43: WRITE-to-READ – Interrupting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Figure 44: WRITE-to -READ – Odd Number of Data, Interrupting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Figure 45: WRITE-to-PRECHARGE – Uninterrupting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Figure 46: WRITE-to-PRECHARGE – Interrupting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Figure 47: WRITE-to-PRECHARGE – Odd Number of Data, Interrupting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Figure 48: Bank WRITE – Without Auto Precharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Figure 49: WRITE – DM Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Figure 50: D ata Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Figure 51: Bank READ – with Auto Precharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Figure 52: Bank WRITE – with Auto Precharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Figure 53: Auto Refresh Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Figure 54: Self Refresh Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDRLOT.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 6©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
List of Tables
List of Tables
Table 1: Key Timing Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Table 2: Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Table 3: Speed Grade Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Table 4: Pin and Ball Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Table 5: IDD Specifications and Conditions (x4, x8, x16: -5B, -6, -6T) – Die Revision K . . . . . . . . . . . . . . . . . . .16
Table 6: IDD Specifications and Conditions (x4, x8, x16: -5B, -6, -6T) – Die Revision M. . . . . . . . . . . . . . . . . . .17
Table 7: Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Table 8: DC Electrical Characteristics and Operating Conditions (-5B). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Table 9: DC Electrical Characteristics and Operating Conditions (-6, -6T, -75E, -75Z, -75) . . . . . . . . . . . . . . .19
Table 10: AC Input Operating Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Table 11: Clock Input Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Table 12: Capacitance (x4, x8 TSOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Table 13: Capacitance (x4, x8 FBGA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Table 14: Capacitance (x16 TSOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Table 15: Capacitance (x16 FBGA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Table 16: Electrical Characteristics and Recommended AC Operating Conditions (-5B) . . . . . . . . . . . . . . . . . .23
Table 17: Electrical Characteristics and Recommended AC Operating Conditions (-6). . . . . . . . . . . . . . . . . . . .25
Table 18: Electrical Characteristics and Recommended AC Operating Conditions (-6T) . . . . . . . . . . . . . . . . . .27
Table 19: Electrical Characteristics and Recommended AC Operating Conditions (-75E) . . . . . . . . . . . . . . . . .29
Table 20: Electrical Characteristics and Recommended AC Operating Conditions (-75Z) . . . . . . . . . . . . . . . . .31
Table 21: Electrical Characteristics and Recommended AC Operating Conditions (-75) . . . . . . . . . . . . . . . . . .33
Table 22: Input Slew Rate Derating Values for Addresses and Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Table 23: Input Slew Rate Derating Values for DQ, DQS, and DM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Table 24: Normal Output Drive Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Table 25: Reduced Output Drive Characte ri s tics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Table 26: Truth Table 1 – Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Table 27: Truth Table 2 – DM Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Table 28: Truth Table 3 – Current State Bank n – Command to Bank n. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Table 29: Truth Table 4 – Current State Bank n – Command to Bank m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Table 30: Command Delays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Table 31: Truth Table 5 – CKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Table 32: Burst Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Table 33: CAS Latency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core1.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 7©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
State Diagram
State Diagram
Figure 1: Simplified State Diagram
Note: This diagram represents operations within a single bank only and does not capture concur-
rent operations in other banks.
Power
on
Power
applied
REFS
LMR REFA
REFSX
ACT
CKE LOW
CKEL
CKE HIGH
CKEH
PRE
Precharge
all banks
MR
EMR
Self
refresh
Idle
all banks
precharged
Row
active Burst
stop
Read
Read A
Automatic sequence
Command sequence
Write
WRITE
WRITE
Write A
WRITE A
Precharge
PREALL
Active
power-
down
Precharge
power-
down
Auto
refresh
PRE
WRITE A READ A
READ A
PRE
PRE
READ A
READ
READ
READ BST
ACT = ACTIVE
BST = BURST TERMINATE
CKEH = Exit power-down
CKEL = Enter power-down
EMR = Extended mode register
LMR = LOAD MODE REGISTER
MR = Mode register
PRE = PRECHARGE
PREALL = PRECHARGE all banks
READ A = READ with auto precharge
REFA = AUTO REFRESH
REFS = Enter self refresh
REFSX = Exit self refresh
WRITE A = WRITE with auto precharge
PRE
LMR
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core1.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 8©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Functional Description
Functional Description
The DDR SDRAM uses a double data rate architecture to achieve high-speed operation.
The double data rate architecture is essentially a 2n-prefetch architecture with an inter-
face designed to transfer two data words per clock cycle at the I/O pins. A single read or
write acce ss for th e DD R SD RA M effe c ti vel y cons is ts of a sing le 2 n-bit-wide, one-clock-
cycle data transfer at the internal DRAM core and two corresponding n-bit-wide, one-
half-clock-cycle data transfers at the I/O pins.
A bidirectional data strobe (DQS) is transmitted externally, along with data, for use in
data capture at the receiver. DQS is a strobe transmitted by the DDR SDRAM during
READs and by the memory controller during WRITEs. DQS is edge-aligned with data for
READs and center-aligned with data for WRITEs. The x16 offering has two data strobes,
one for the lower byte and one for the upper byte.
The DDR SDRAM operates from a differential clock (CK and CK#); the crossing of CK
going HIGH and CK# going LOW will be referred to as the positive edge of CK.
Commands (addre ss and control signals) are registered at every positive edge of CK.
Input data is registered on both edges of DQS, and output data is referenced to both
edges of DQS, as well as to both edges of CK.
Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a
selected location and continue for a pr ogramme d number of locations in a progr ammed
sequence . A ccesses be gin with the r egi strati on of an ACTIVE command, which may then
be followed by a READ or WRITE command. The add ress bits registered coincident with
the ACTIVE command are use d to select the bank and row to be accessed. The address
bits re gistere d coincident with the READ or WRITE command are used to select the bank
and the starting column location for the burst access.
The DDR SDRAM provides for programmable READ or WRITE burst lengths of 2, 4, or 8
locations. An auto precharge function may be enabled to provide a self-timed row
precharge that is initiated at the end of the burst access.
As with standard SDR SDRAMs, the pipelined, multibank architecture of DDR SDRAMs
allows for concurrent operation, thereby providing high effective bandwidth by hiding
row precharge and activation time.
An auto refresh mode is provided, along with a power-saving power-down mode . All
inputs are compatible with the JEDEC standard for SSTL_2. All full-drive option outputs
are SSTL_2, Class II compatible.
General Notes The functionality and the timing specifications discussed in this data sheet are for the
DLL-enabled mode of operation.
Throughout the data sheet, the various figures and text refer to DQs as “DQ.” The DQ
term is to be interpreted as any and all DQ collectively, unless specifically stated
otherwise. Additionally, the x16 is divided into two bytes, the lower byte and upper
byte. For the lower byte (DQ[7:0]) DM refers to LDM and DQS refers to LDQS. For the
upper byte (DQ[15:8]) DM refers to UDM and DQS refers to UDQS.
Complete functionality is described throughout the document and any page or
diagram may have been simplified to convey a topic and may not be inclusive of all
requirements.
Any specific requirement takes precedence over a general statement.
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 9©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Functional Block Diagrams
Functional Block Diagrams
The 256Mb DDR SDRAM is a high-speed CMOS, dynamic random-access memory
containing 268,435,456 bits. It is internally configured as a 4-bank DRAM.
Figure 1: 64 Meg x 4 Functional Block Diagram
13
RAS#
CAS#
Row-
address
MUX
CK
CS#
WE#
CK#
11
A[12:0],
BA[1:0]
CKE
13
15
1024
(x8)
8192
8192
15
13
10
1
2
2
4
4
4
1
1
1
1
11
8
8
2
8
CK
out
DQS
CK
CK
in
MUX
4
4
4
44
8
DQ[3:0]
DQS
DM
1
WRITE
FIFO
and
drivers
Control
logic
Mode registers
Command
decode
Refresh
counter
Address
register Bank
control
logic
Column-
address
counter/
latch
Column
decoder
I/O gating
DM mask logic
Bank 0
row-
address
latch
and
decoder
Bank 0
memory
array
(8192 x 1024 x 8)
Sense amplifiers
Bank 1 Bank 2 Bank 3
READ
latch
Data
CK
DLL
Drivers
DQS
generator
Input
registers
Rcvrs
Data
Mask
Column 0
Column 0
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 10 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Functional Block Diagrams
Figure 2: 32 Meg x 8 Functional Block Diagram
Figure 3: 16 Meg x 16 Functional Block Diagram
13
RAS#
CAS#
ROW-
ADDRESS
MUX
CK
CS#
WE#
CK#
CONTROL
LOGIC
COLUMN-
ADDRESS
COUNTER/
LATCH
MODE REGISTERS
10
COMMAND
DECODE
A[12:0],
BA[1:0]
CKE
13
ADDRESS
REGISTER
15
512
(x16)
8192
I/O GATING
DM MASK LOGIC
COLUMN
DECODER
BANK0
MEMORY
ARRAY
(8192 x 512 x 16)
BANK0
ROW-
ADDRESS
LATCH
&
DECODER
8192
SENSE AMPLIFIERS
BANK
CONTROL
LOGIC
15
BANK1BANK2 BANK3
13
9
2
2
REFRESH
COUNTER
8
8
8
1
INPUT
REGISTERS
1
1
1
1
RCVRS
1
16
16
2
16
CK
Out
DATA
DQS
MASK
DATA
CK
CK
CK
In
DRVRS
DLL
MUX
DQS
GENERATOR
8
8
8
88
16
DQ[7:0]
DQS
1
READ
LATCH
WRITE
FIFO
&
DRIVERS
1
COL0
COL0
DM
13
RAS#
CAS#
ROW-
ADDRESS
MUX
CK
CS#
WE#
CK#
CONTROL
LOGIC
COLUMN-
ADDRESS
COUNTER/
LATCH
MODE REGISTERS
9
COMMAND
DECODE
A[12:0],
BA[1:0]
CKE
13
ADDRESS
REGISTER
15
256
(x32)
8192
I/O GATING
DM MASK LOGIC
COLUMN
DECODER
BANK0
MEMORY
ARRAY
(8192 x 256 x 32)
BANK0
ROW-
ADDRESS
LATCH
&
DECODER
8192
SENSE AMPLIFIERS
BANK
CONTROL
LOGIC
15
BANK1BANK2 BANK3
13
8
2
2
REFRESH
COUNTER
16
16
16
2
INPUT
REGISTERS
2
2
2
2
RCVRS
2
32
32
4
32
CK
Out
DATA
DQS
MASK
DATA
CK
CK
CK
In
DRVRS
DLL
MUX
DQS
GENERATOR
16
16
16
16 16
32
DQ[15:0]
LDQS
UDQS
2
READ
LATCH
WRITE
FIFO
&
DRIVERS
1
COL0
COL0
LDM,
UDM
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 11 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Pin and Ball Assignments and Descriptions
Pin and Ball Assignments and Descriptions
Figure 4: 66-Pin TSOP Pin Assignments (Top View)
x4 x16 x4x8x16
VSS
DQ15
VSSQ
DQ14
DQ13
VDDQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
NC
VSSQ
UDQS
DNU
VREF
VSS
UDM
CK#
CK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
VSS
VSS
DQ7
VSSQ
NC
DQ6
VDDQ
NC
DQ5
VSSQ
NC
DQ4
VDDQ
NC
NC
VSSQ
DQS
DNU
VREF
VSS
DM
CK#
CK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
VSS
VSS
NF
VSSQ
NC
DQ3
VDDQ
NC
NF
VSSQ
NC
DQ2
VDDQ
NC
NC
VSSQ
DQS
DNU
VREF
VSS
DM
CK#
CK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
VSS
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
VDD
DQ0
VDDQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VDDQ
DQ5
DQ6
VSSQ
DQ7
NC
VDDQ
LDQS
NC
VDD
DNU
LDM
WE#
CAS#
RAS#
CS#
NC
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
x8
VDD
DQ0
VDDQ
NC
DQ1
VSSQ
NC
DQ2
VDDQ
NC
DQ3
VSSQ
NC
NC
VDDQ
NC
NC
VDD
DNU
NC
WE#
CAS#
RAS#
CS#
NC
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
VDD
NF
VDDQ
NC
DQ0
VSSQ
NC
NF
VDDQ
NC
DQ1
VSSQ
NC
NC
VDDQ
NC
NC
VDD
DNU
NC
WE#
CAS#
RAS#
CS#
NC
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 12 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Pin and Ball Assignments and Descriptions
Figure 5: 60-Ball FBGA Ball Assignments (Top View)
VSSQ
DQ14
DQ12
DQ10
DQ8
V
REF
DQ15
VDDQ
VSSQ
VDDQ
VSSQ
V
SS
CK
A12
A11
A8
A6
A4
V
SS
DQ13
DQ11
DQ9
UDQS
UDM
CK#
CKE
A9
A7
A5
V
SS
V
DD
DQ2
DQ4
DQ6
LDQS
LDM
WE#
RAS#
BA1
A0
A2
V
DD
DQ0
VSSQ
VDDQ
VSSQ
VDDQ
V
DD
CAS#
CS#
BA0
A10
A1
A3
VDDQ
DQ1
DQ3
DQ5
DQ7
DNU
x16 (Top View)
VSSQ
NC
NC
NC
NC
V
REF
NF
VDDQ
VSSQ
VDDQ
VSSQ
V
SS
CK
A12
A11
A8
A6
A4
V
SS
DQ3
NF
DQ2
DQS
DM
CK#
CKE
A9
A7
A5
V
SS
V
DD
DQ0
NF
DQ1
NC
NC
WE#
RAS#
BA1
A0
A2
V
DD
NF
VSSQ
VDDQ
VSSQ
VDDQ
V
DD
CAS#
CS#
BA0
A10
A1
A3
VDDQ
NC
NC
NC
NC
DNU
x4 (Top View)
VSSQ
NC
NC
NC
NC
V
REF
DQ7
VDDQ
VSSQ
VDDQ
VSSQ
V
SS
CK
A12
A11
A8
A6
A4
V
SS
DQ6
DQ5
DQ4
DQS
DM
CK#
CKE
A9
A7
A5
V
SS
V
DD
DQ1
DQ2
DQ3
NC
NC
WE#
RAS#
BA1
A0
A2
V
DD
DQ0
VSSQ
VDDQ
VSSQ
VDDQ
V
DD
CAS#
CS#
BA0
A10
A1
A3
VDDQ
NC
NC
NC
NC
DNU
x8 (Top View)
A
123456789
B
C
D
E
F
G
H
J
K
L
M
A
123456789
B
C
D
E
F
G
H
J
K
L
M
A
123456789
B
C
D
E
F
G
H
J
K
L
M
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 13 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Pin and Ball Assignments and Descriptions
Table 1: Pin and Ball Descriptions
Symbol Type Description
A[12:0] Input Address inputs: Provide the row address for ACTIVE commands, and the column address and
auto precharge bit (A10) for READ/WRITE commands, to select one location out of the memory
array in the respective bank. A10 sampled during a PRECHARGE command determines whether
the PRECHARGE applies to one bank (A10 LOW, bank sel ected by BA[1:0]) or all banks (A10
HIGH). The address inputs also provide the op -code during a LOAD MODE REGISTER command.
BA[1:0] Input Bank address inputs: BA[1:0] define to whic h bank an ACTIVE, READ, WRI TE, or PRECHARGE
command is being appli ed . BA [1:0] also define which mode register (mode register or extended
mode register) is loaded during the LOAD MODE REGISTER (LMR) command.
CK, CK# Input Clock: CK and CK# are differential clock inpu ts. All address and control input signal s are
sampled on the crossing of the pos itive edge of CK and the nega tive edge of CK#. Output data
(DQ and DQS) is referenced to the crossings of CK and CK#.
CKE Input Clock enable: CKE HIGH activates and CKE LOW deactivates the internal cl oc k, input buffers,
and output drivers. Taking CKE LOW provides PRECHARGE POWER-DOWN and SELF REFRESH
operations (all banks idle) or ACTIVE POWER-DOWN (row ACTIVE in any bank). CKE is
synchronous for POWER-DOWN entry and exit and for SELF REFRESH entry. CKE is asynchronous
for SELF REFRESH exit and for disabling the outputs. CKE must be maintained HIGH throughout
read and write accesses. Input buffers (excluding CK, CK#, and CKE) are disabled during POWER-
DOWN. Input buf fers (exclu din g CKE) are disabled during SELF REFRESH. CKE is an SSTL_2 input
but will dete ct an LVCMO S LOW level after VDD is applied and until CKE is first bro ught HIGH,
after which it becomes a SST L_2 input only.
CS# Input Chip select: CS# enables (registered LOW) and disables (registered HIGH) the command
decoder. All commands are masked when CS# is registered HIGH. CS# provides for external bank
selection on systems with multiple banks. CS# is considere d part of the command code.
DM
LDM, UDM Input Input data mask: DM is an input mask signal for write data. Input data is masked when DM is
sampled HIGH along with that input data duri n g a WRITE access. DM is sampled on both edges
of DQS. Although DM pins are input-only, the DM loading is designed to match that of DQ and
DQS pins. For x16 devices, LDM is DM for DQ[7:0], and UDM is DM for DQ[15:8]. Pin 20 is NC on
x4 and x8 devices.
RAS#, CAS#,
WE# Input Command inputs: RAS#, CAS#, and WE# (along with CS#) define the command being entered.
DQ[15:0] I/O Data input/output: Data bus for x16 devices.
DQ[7:0] I/O Data input/output: Data bus for x8 devices.
DQ[3:0] I/O Data input/output: Data bus for x4 devices.
DQS
LDQS, UDQS I/O Data strobe: Output with read data; input with write data. DQS is edge-aligned with read
data; centered in write data. It is used to capture data. For x16 devices, LDQS is DQS for DQ[7:0],
and UDQS is DQS for DQ[15:8]. Pin 16 (E7) is NC for x4 and x8 devices.
VDD Supply Power supply.
VDDQ Supply DQ power supply: Isolated on the die for improved noise immunity.
VSS Supply Ground.
VSSQSupply DQ ground: Isolated on the die for improved noise immunity.
VREF Supply SSTL_2 reference voltage.
NC No connect for x16, x8, x4: These pins should be left unconnected.
DNU Do not use: Must float to minimize noise on VREF.
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 14 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Package Dimensions
Package Dimensions
Figure 6: 66-Pin Plastic TSOP (400 mil)
Notes: 1. All dimensions in millimeters.
2. Package width and length do not inclu de mold protrusio n; allowable mol d protru sio n is
0.25mm per side.
SEE DETAIL A
0.10
0.65 TYP 0.71
10.16 ±0.08
0.15
0.50 ±0.10
PIN #1 ID
DETAIL A
22.22 ± 0.08
0.32 ±0.075TYP
+0.03
–0.02
+0.10
–0.05
1.20 MAX 0.10
0.25
0.80 TYP
0.10 (2X)
GAGE PLANE
11.76 ± 0.20
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 15 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Package Dimensions
Figure 7: 60-Ball FBGA (8mm x 12.5mm)
Notes: 1. All dimensions are in millimeters.
2. Topside part marking decoder can be found on Micro n’s Web site.
Ball A1 ID
1.20 MAX
8 ±0.15
Ball A1 ID
60X Ø0.45
Solder ball material:
eutectic or SAC305.
Dimensions apply
to solder balls post-
reflow on Ø0.33
NSMD ball pads.
1 TYP
11 CTR 12.5 ±0.15
0.8 ±0.1
0.12 A A
Seating
plane
6.4 CTR
0.8 TYP
0.25 MIN
9 8 7 3 2 1
A
B
C
D
E
F
G
H
J
K
L
M
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 16 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – I
DD
Electrical Specifications – IDD
Table 2: IDD Specifications and Conditions (x4, x8, x16: -5B, -6, -6T) – Die Revision K
VDDQ = 2.6V ±0.1V, VDD = 2.6V ±0.1V (-5B); VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V (-6, -6T);
0°C TA 70°C; Notes: 1–5, 11, 13, 15, 47; Notes appear on pages 35–40; See also Table 1 on page 18
Parameter/Condition Symbol -5B -6/6T Units Notes
Operating one-bank precharge current: tRC = tRC (MIN);
tCK = tCK (MIN); DQ, DM, and DQS inputs changing once per
clock cycle; Address and control inputs changing once every
two clock cycles
IDD0 100 90 mA 23, 48
Operating one-bank active-read-precharge current:
Burst = 4; tRC = tRC (MIN); tCK = tCK (MIN); IOUT =0mA;
Address and control inputs changing once per clock cycle
IDD1 120 115 mA 23, 48
Precharge power-down standby current: All banks idle;
Power-down mode; tCK = tCK (MIN); CKE = LOW IDD2P 44mA24, 33
Idle standby current: CS# = HIGH; All banks are idle;
tCK = tCK (MIN); CKE = HIGH; Address and other control
inputs changing once per clock cycle; VIN =V
REF for DQ, DQS,
and DM
IDD2F 50 50 mA 51
Active power-down standby current: One bank active;
Power-down mode; tCK = tCK (MIN); CKE = LOW IDD3P 35 30 mA 24, 33
Active standby current: CS# = HIGH; CKE = HIGH; One bank
active; tRC = tRAS (MAX); tCK = tCK (MIN); DQ, DM, and DQS
inputs changing twice per clock cycle; Address and other
control inputs chan gi ng once per clock cycle
IDD3N 60 55 mA 23
Operating burst r ead curren t: Burst = 2; Continuous
burst reads; One bank active; Address and control inputs
changing once per clock cycle; tCK = tCK (MIN); IOUT =0mA
IDD4R 180 160 mA 23, 48
Operating burst write current: Burst = 2; Continuous burst
writes; One bank active; Address and control inputs changing
once per clock cycle; tCK = tCK (MIN); DQ, DM, and DQS inputs
changing twice pe r clock cycle
IDD4W 180 160 mA 23
Auto refresh burst current: tREFC = tRFC (MIN) IDD5 160 160 mA 50
tREFC =7.8µs IDD5A 66mA28, 50
Self refresh current: CKE 0.2V Standard IDD6 44mA 12
Low power (L) IDD6A 22mA 12
Operating bank interleave read current: Four-bank
interleaving READs (burst = 4) with auto precharge;
tRC = minimum tRC allowed; tCK = tCK (MIN); Address and
control inputs change only during ACTIVE, READ, or WRITE
commands
IDD7 290 270 mA 23, 49
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
256Mb_DDR_x4x8x16_D2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 17 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – I
DD
Table 3: IDD Specifications and Conditions (x4, x8, x16: -5B, -6, -6T) – Die Revision M
VDDQ = 2.6V ±0.1V, VDD = 2.6V ±0.1V (-5B); VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V (-6, -6T);
0°C TA 70°C; Notes: 1–5, 11, 13, 15, 47; Notes appear on pages 35–40; See also Table 1 on page 18
Parameter/Condition Symbol -5B -6/6T Units Notes
Operating one-bank precharge current: tRC = tRC (MIN);
tCK = tCK (MIN); DQ, DM, and DQS inputs changing once per clock
cycle; Address and control inputs changing on ce every two clock cycles
IDD0 75 65 mA 23, 48
Operating one-bank active-read-precharge current: Burst = 4;
tRC = tRC (MIN); tCK = tCK (MIN); IOUT = 0mA; Address and control
inputs changing once per clock cycle
IDD1 85 75 mA 23, 48
Precharge power-down standby current: All banks idle; Power-
down mode; tCK = tCK (MIN); CKE = LOW IDD2P 4 4 mA 24, 33
Idle standby current: CS# = HIGH; All banks are idle; tCK = tCK (MIN);
CKE = HIGH; Address and other control inputs changing once per clock
cycle; VIN =V
REF for DQ, DQS, and DM
IDD2F 23 23 mA 51
Active power-down standby current: One bank active; Power-
down mode; tCK = tCK (MIN); CKE = LOW IDD3P 14 14 mA 24, 33
Active standby current: CS# = HIGH; CKE = HIGH; One bank active;
tRC = tRAS (MAX); tCK = tCK (MIN); DQ, DM, and DQS inputs changin g
twice per clock cycle; Address and other control inputs changing once
per clock cycle
IDD3N 30 30 mA 23
Operating burst r ead curren t: Burst = 2; Continuous burst reads;
One bank active; Address and control inputs changing once per clock
cycle; tCK = tCK (MIN); IOUT =0mA
IDD4R 105 95 mA 23, 48
Operating burst write current: Burst = 2; Continuous burst writes;
One bank active; Address and control inputs changing once per clock
cycle; tCK = tCK (MIN); DQ, DM, and DQS inputs changing twice per
clock cycle
IDD4W 105 95 mA 23
Auto refresh burst current: tREFC = tRFC (MIN) IDD5 115 105 mA 50
tREFC = 7.8µs IDD5A 6 6 mA 28, 50
Self refresh current: CKE 0.2V Standard IDD6 44mA12
Low power (L) IDD6A 22mA12
Operating bank interleave read current: Four-bank interleaving
READs (burst = 4) with auto precharge; tRC = minimum tRC allowed;
tCK = tCK (MIN); Address and control inputs change only during
ACTIVE, READ, or WRITE commands
IDD7 175 175 mA 23, 49
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 18 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Electrical Specifications – DC and AC
S tresses greater than those listed in Table 1 may cause permanent damage to the d evice.
This is a stress rating only, and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may
affect reli ability.
Table 1: Absolute Maximum Ratings
Parameter Min Max Units
VDD supply voltage relative to VSS –1V 3.6V V
VDDQ supply voltage relative to VSS –1V 3.6V V
VREF and inputs voltage relative to VSS –1V 3.6V V
I/O pins voltage relative to VSS –0.5V VDDQ + 0.5V V
Storage temperature (plastic) –55 150 °C
Short circuit output cur r e nt –50mA
Table 2: DC Electrical Characteristics and Operating Conditions (-5B)
Notes: 1–5 and 17 apply to the entire table; Notes appear on page 35; VDDQ = 2.6V ±0.1V, VDD = 2.6V ±0.1V
Parameter/Condition Symbol Min Max Units Notes
Supply voltage VDD 2.5 2.7 V 37, 42
I/O supply voltage VDDQ 2.5 2.7 V 37, 42, 45
I/O reference voltage VREF 0.49 × VDDQ 0.51 × VDDQ V7, 45
I/O termination voltage (system) VTT VREF - 0.04 VREF + 0.04 V 8, 45
Input high (logi c 1) vol tag e VIH(DC) VREF + 0.15 VDD + 0.3 V 29
Input low (logic 0) voltage VIL(DC) –0.3 VREF - 0.15 V 29
Input leakage current:
Any input 0V VIN VDD, VREF pin 0V VIN 1.35V
(All other pins not under test = 0V)
II–2 2 µA
Output leakage current:
(DQ are disabled; 0V VOUT VDDQ)IOZ –5 5 µA
Full-drive option output
levels (x4, x8, x16): High current (VOUT =
VDDQ - 0.373V, minimum
VREF, minimum VTT)
IOH –16.8 mA 38, 40
Low current (VOUT =
0.373V, maximum VREF,
maximum VTT)
IOL 16.8 mA
Reduced-drive option
output levels (Design
Revision F and K only):
High current (VOUT =
VDDQ - 0.373V, minimum
VREF, minimum VTT)
IOHR –9 mA 39, 40
Low current (VOUT =
0.373V, maximum VREF,
maximum VTT)
IOLR 9–mA
Ambient operating
temperatures Commercial TA070°C
Industrial TA–40 85 °C
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 19 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 3: DC Electrical Characteristics and Operating Conditions (-6, -6T, -75E, -75Z, - 75)
Notes: 1–5 and 17 apply to the entire table; Notes appear on page 35; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
Parameter/Condition Symbol Min Max Units Notes
Supply voltage VDD 2.3 2.7 V 37, 42
I/O supply voltage VDDQ 2.3 2.7 V 37, 42, 45
I/O reference voltage VREF 0.49 × VDDQ 0.51 × VDDQ V7, 45
I/O termination voltage (system) VTT VREF - 0.04 VREF + 0.04 V 8, 45
Input high (logi c 1) vol tag e VIH(DC) VREF + 0.15 VDD + 0.3 V 29
Input low (logic 0) voltage VIL(DC) –0.3 VREF - 0.15 V 29
Input leakage current:
Any input 0V VIN VDD, VREF pin 0V VIN 1.35V
(All other pins not under test = 0V)
II–2 2 µA
Output leakage current:
(DQ are disabled; 0V VOUT VDDQ)IOZ –5 5 µA
Full-drive option output
levels (x4, x8, x16): High current (VOUT =
VDDQ - 0.373V, minimum
VREF, minimum VTT)
IOH –16.8 mA 38, 40
Low current (VOUT =
0.373V, maximum VREF,
maximum VTT)
IOL 16.8 mA
Reduced-drive option
output levels (Design
Revision F and K only):
High current (VOUT =
VDDQ - 0.373V, minimum
VREF, minimum VTT)
IOHR –9 mA 39, 40
Low current (VOUT =
0.373V, maximum VREF,
maximum VTT)
IOLR 9–mA
Ambient operating
temperatures Commercial TA070°C
Industrial TA–40 85 °C
Table 4: AC Input Operating Conditions
Notes: 1–5 and 17 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0 .2V (VDDQ = 2.6V ±0.1V, VDD = 2.6V ±0.1V for -5B)
Parameter/Condition Symbol Min Max Units Notes
Input high (logi c 1) vol tag e VIH(AC) VREF + 0.310 V 15, 29, 41
Input low (logic 0) voltage VIL(AC) –V
REF - 0.310 V 15, 29, 41
I/O reference voltage VREF(AC) 0.49 × VDDQ 0.51 × VDDQ V7
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 20 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Figure 1: Input Voltage Waveform
Notes: 1. VOH,min with test load is 1.927V.
2. VOL,max with test load is 0.373V.
3. Numbers in diagram reflect nominal values utilizing circuit below for all devi ces oth er than
-5B.
0.940V
1.100V
1.200V
1.225V
1.250V
1.275V
1.300V
1.400V
1.560V
VIL(AC)
VIL(DC)
VREF - AC noise
VREF - DC error
VREF + DC error
VREF + AC noise
Receiver
Transmitter
VIH(DC)
VIH(AC)
VOH,min (1.670V1 for SSTL_2 termination)
VIN(AC) - provides margin
between VOL,max
and VIL(AC)
VSSQ
VDDQ,min (2.3V)
VOL,max (0.83V2 for SSTL_2
termination)
System noise margin (power/ground,
crosstalk, signal integrity attenuation)
Reference
point
25Ω
25Ω
V
TT
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 21 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Figure 2: SSTL_2 Clock Input
Notes: 1. CK or CK# may not be more positive than VDDQ + 0.3V or more negative than VSS - 0.3V.
2. This provides a minimum of 1.1 5V to a maximum of 1.35V an d is al wa ys ha l f of VDDQ.
3. CK and CK# must cross in this region.
4. CK and CK# must meet at least VID(DC),min when static and is centered around VMP(DC).
5. CK and CK# must have a minimum 700mV peak-to-peak swing.
6. For AC operation, al l DC clock requirements must also be satisfied.
7. Numbers in diagram reflect nominal values for all device s other than -5B.
Table 5: Clock Input Operating Conditions
Notes: 1–5, 16, 17, and 31 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0 .2V (VDDQ = 2.6V ±0.1V, VDD = 2.6V ±0.1V for -5B)
Parameter/Condition Symbol Min Max Units Notes
Clock input mi d-p oi nt voltage: CK and CK# VMP(DC) 1.15 1.35 V 7, 10
Clock input vol tage level: CK and CK# VIN(DC) –0.3 VDDQ + 0.3 V 7
Clock input differential voltage: CK and CK# VID(DC) 0.36 VDDQ + 0.6 V 7, 9
Clock input differential voltage: CK and CK# VID(AC) 0.7 VDDQ + 0.6 V 9
Clock input crossing point voltage: CK and CK# VIX(AC) 0.5 × VDDQ - 0.2 0.5 × VDDQ + 0.2 V 10
CK
CK#
2.80V Maximum clock level
1
Minimum clock level
1
–0.30V
1.25V
1.45V
1.05V V
ID(AC)5
V
ID(DC)4
X
V
MP(DC)2
V
IX(AC)3
X
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 22 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 6: Capacitance (x4, x8 TSOP)
Note: 14 applies to the entire table; Notes appear on page 35
Parameter Symbol Min Max Units Notes
Delta input/output capacitance: DQ[3:0] (x4), DQ[7:0] (x8) DCIO –0.50pF 25
Delta input cap a citance: Command and address DCI1 –0.50pF 30
Delta input capacitance: CK, CK# DCI2 –0.25pF 30
Input/outp ut ca paci tance: DQ, DQS, DM CIO 4.0 5.0 pF
Input capacitance: Command and address CI1 2.0 3.0 pF
Input capacitance: CK, CK# CI2 2.0 3.0 pF
Input capacitance: CKE CI3 2.0 3.0 pF
Table 7: Capacitance (x4, x8 FBGA)
Note: 14 applies to the entire table; Notes appear on page 35
Parameter Symbol Min Max Units Notes
Delta input/output capacitance: DQ, DQS, DM DCIO –0.50pF 25
Delta input cap a citance: Command and address DCI1 –0.50pF 30
Delta input capacitance: CK, CK# DCI2 –0.25pF 30
Input/outp ut ca paci tance: DQ, DQS, DM CIO 3.5 4.5 pF
Input capacitance: Command and address CI1 1.5 2.5 pF
Input capacitance: CK, CK# CI2 1.5 2.5 pF
Input capacitance: CKE CI3 1.5 2.5 pF
Table 8: Capacitance (x16 TSOP)
Note: 14 applies to the entire table; Notes appear on page 35
Parameter Symbol Min Max Units Notes
Delta input/output capacitance: DQ[7:0], LDQS, LDM DCIOL –0.50pF 25
Delta input/output capacitance: DQ[15:8], UDQS, UDM DCIOU –0.50pF 25
Delta input cap a citance: Command and address DCI1 –0.50pF 30
Delta input capacitance: CK, CK# DCI2 –0.25pF 30
Input/outp ut ca paci tan ce: DQ , LDQS, UDQS, LDM, UDM CIO 4.0 5.0 pF
Input capacitance: Command and address CI1 2.0 3.0 pF
Input capacitance: CK, CK# CI2 2.0 3.0 pF
Input capacitance: CKE CI3 2.0 3.0 pF
Table 9: Capacitance (x16 FBGA)
Note: 14 applies to the entire table; Notes appear on page 35
Parameter Symbol Min Max Units Notes
Delta input/output capacitance: DQ[7:0], LDQS, LDM DCIOL –0.50pF 25
Delta input/output capacitance: DQ[15:8], UDQS, UDM DCIOU –0.50pF 25
Delta input cap a citance: Command and address DCI1 –0.50pF 30
Delta input capacitance: CK, CK# DCI2 –0.25pF 30
Input/outp ut ca paci tan ce: DQ , LDQS, UDQS, LDM, UDM CIO 3.5 4.5 pF
Input capacitance: Command and address CI1 1.5 2.5 pF
Input capacitance: CK, CK# CI2 1.5 2.5 pF
Input capacitance: CKE CI3 1.5 2.5 pF
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 23 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 10: Electrical Characteristics and Recommended AC Operating Conditions (-5B)
Notes 1–6, 16–18, and 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.6V ±0.1V, VDD = 2.6V ±0.1V
AC Characteristics -5B
Units NotesParameter Symbol Min Max
Access window of DQ from CK/CK# tAC –0.70 0.70 ns
CK high-level width tCH 0.45 0.55 tCK 31
Clock cycle time CL = 3 tCK (3) 5 7.5 ns 52
CL = 2.5 tCK (2.5) 6 13 ns 46, 52
CL = 2 tCK (2) 7.5 13 ns 46, 52
CK low-level width tCL 0.45 0.55 tCK 31
DQ and DM input hold time relative to DQS tDH 0.40 ns 27, 32
DQ and DM input pu lse width (for eac h input) tDIPW 1.75 ns 32
Access window of DQS from CK/CK# tDQSCK –0.60 0.60 ns
DQS input high pulse width tDQSH 0.35 tCK
DQS input low pulse width tDQSL 0.35 tCK
DQS–DQ skew, DQS to last DQ valid, per group, per access tDQSQ 0.40 ns 26, 27
WRITE command to first DQS latching transition tDQSS 0.72 1.28 tCK
DQ and DM input setup time relative to DQS tDS 0.40 ns 27, 32
DQS falling edge from CK rising – hold time tDSH 0.2 – tCK
DQS falling edge to CK rising – setup time tDSS 0.2 – tCK
Half-clock period tHP tCH,tCL ns 35
Data-out High-Z window from CK/CK# tHZ 0.70 ns 19, 43
Address and control input hold time (slew rate 0.5 V/n s) tIHF0.60 ns 15
Address and control input pulse width (for each input) tIPW 2.2 ns
Address and control input setup time (slew rate 0.5 V/ns) tISF0.60 ns 15
Data-out Low-Z window from CK/CK# tLZ –0.70 ns 19, 43
LOAD MODE REGISTER command cycle time tMRD 10 ns
DQ–DQS hold, DQS to first DQ to go non-valid, per access tQH tHP -tQHS ns 26, 27
Data hold skew factor tQHS 0.50 ns
ACTIVE-to-READ with auto precharge command tRAP 15 ns
ACTIVE-to-PRECHARGE command tRAS 40 70,000 ns 36
ACTIVE-to-ACTIVE/AUTO REFRESH command period tRC 55 ns 55
ACTIVE-to-READ or WRITE delay tRCD 15 ns
REFRESH-to-REFRESH command interval tREFC 70.3 µs 24
Average periodic refresh interval tREFI 7.8 µs 24
AUTO REFRESH command period tRFC 70 ns 50
PRECHARGE command period tRP 15 ns
DQS read preamble tRPRE 0.9 1.1 tCK 44
DQS read postamble tRPST 0.4 0.6 tCK 44
ACTIVE bank a to ACTIVE bank b command tRRD 10 ns
Terminating voltage delay to VDD tVTD 0 ns
DQS write preamble tWPRE 0.25 tCK
DQS write preamble setup time tWPRES 0 ns 21, 22
DQS write postamble tWPST 0.4 0.6 tCK 20
Write recovery time tWR 15 ns
Internal WRITE-to-READ command delay tWTR 2 tCK
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 24 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Exit SELF REFRESH-to-non-READ command tXSNR 70 ns
Exit SELF REFRESH-to-READ command tXSRD 200 tCK
Data valid output window n/a tQH - tDQSQ ns 26
Table 10: Electrical Characteristics and Recommended AC Operating Conditions (-5B) (continued)
Notes 1–6, 16–18, and 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.6V ±0.1V, VDD = 2.6V ±0.1V
AC Characteristics -5B
Units NotesParameter Symbol Min Max
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 25 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 11: Electrical Characteristics and Recommended AC Operating Conditions (-6)
Notes: 1–6, 16–18, 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -6 (FBGA)
Units NotesParameter Symbol Min Max
Access window of DQ from CK/CK# tAC –0.70 0.70 ns
CK high-level width tCH 0.45 0.55 tCK 31
Clock cycle time CL = 2.5 tCK (2.5) 6 13 ns 46, 52
CL = 2 tCK (2) 7.5 13 ns 46, 52
CK low-level width tCL 0.45 0.55 tCK 31
DQ and DM input hold time relative to DQS tDH 0.45 ns 27, 32
DQ and DM input pu lse width (for eac h input) tDIPW 1.75 ns 32
Access window of DQS from CK/CK# tDQSCK –0.6 0.6 ns
DQS input high pulse width tDQSH 0.35 tCK
DQS input low pulse width tDQSL 0.35 tCK
DQS–DQ skew, DQS to last DQ valid, per group, per access tDQSQ 0.4 ns 26, 27
WRITE command to first DQS latching transition tDQSS 0.75 1.25 tCK
DQ and DM input setup time relative to DQS tDS 0.45 ns 27, 32
DQS falling edge from CK rising - hold time tDSH 0.2 tCK
DQS falling edge to CK rising - setup time tDSS 0.2 tCK
Half-clock period tHP tCH, tCL ns 35
Data-out High-Z window from CK/CK# tHZ 0.7 ns 19, 43
Address and control input hold time (fast slew rate) tIHF0.75 ns
Address and control input hold time (slow slew rate) tIHS0.8 ns 15
Address and control input pulse width (for each input) tIPW 2.2 ns
Address and control input setup time (fast slew rate) tISF0.75 ns
Address and control input setup time (slow slew rate) tISS0.8 ns 15
Data-out Low-Z window from CK/CK# tLZ –0.7 ns 19, 43
LOAD MODE REGISTER command cycle time tMRD 12 ns
DQ-DQS hold, DQS to first DQ to go non-valid, per access tQH tHP -tQHS ns 26, 27
Data hold skew factor tQHS 0.50 ns
ACTIVE-to-READ with auto precharge command tRAP 15 ns
ACTIVE-to-PRECHARGE command tRAS 42 7 0,000 ns 36, 54
ACTIVE-to-ACTIVE/AUTO REFRESH command period tRC 60 ns 55
ACTIVE-to-READ or WRITE delay tRCD 15 ns
REFRESH-to-REFRESH command interval tREFC 70.3 µs 24
Average periodic refresh interval tREFI 7.8 µs 24
AUTO REFRESH command period tRFC 72 ns 50
PRECHARGE command period tRP 15 ns
DQS read preamble tRPRE 0.9 1.1 tCK 44
DQS read postamble tRPST 0.4 0.6 tCK 44
ACTIVE bank a to ACTIVE bank b command tRRD 12 ns
Terminating voltage delay to VSS tVTD 0 ns
DQS write preamble tWPRE 0.25 tCK
DQS write preamble setup time tWPRES 0 ns 21, 22
DQS write postamble tWPST 0.4 0.6 tCK 20
Write recovery time tWR 15 ns
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 26 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Internal WRITE-to-READ command delay tWTR 1 tCK
Exit SELF REFRESH-to-non-READ command tXSNR 75 ns
Exit SELF REFRESH-to-READ command tXSRD 200 tCK
Data valid output window n/a tQH - tDQSQ ns 26
Table 11: Electrical Characteristics and Recommended AC Operating Conditions (-6) (continued)
Notes: 1–6, 16–18, 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -6 (FBGA)
Units NotesParameter Symbol Min Max
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 27 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 12: Electrical Characteristics and Recommended AC Operating Conditions (-6T)
Notes: 1–6, 16–18, and 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -6T (TSOP)
Units NotesParameter Symbol Min Max
Access window of DQ from CK/CK# tAC –0.70 0.70 ns
CK high-level width tCH 0.45 0.55 tCK 31
Clock cycle time CL = 2.5 tCK (2.5) 6 13 ns 46, 52
CL = 2 tCK (2) 7.5 13 ns 46, 52
CK low-level width tCL 0.45 0.55 tCK 31
DQ and DM input hold time relative to DQS tDH 0.45 ns 27, 32
DQ and DM input pu lse width (for eac h input) tDIPW 1.75 ns 32
Access window of DQS from CK/CK# tDQSCK –0.6 0.6 ns
DQS input high pulse width tDQSH 0.35 tCK
DQS input low pulse width tDQSL 0.35 tCK
DQS–DQ skew, DQS to last DQ valid, per group, per access tDQSQ 0.45 ns 26, 27
WRITE command to first DQS latching transition tDQSS 0.75 1.25 tCK
DQ and DM input setup time relative to DQS tDS 0.45 ns 27, 32
DQS falling edge from CK rising - hold time tDSH 0.2 tCK
DQS falling edge to CK rising - setup time tDSS 0.2 tCK
Half-clock period tHP tCH,
tCL –ns35
Data-out High-Z window from CK/CK# tHZ 0.7 ns 19, 43
Address and control input hold time (fast slew rate) tIHF0.75 ns
Address and control input hold time (slow slew rate) tIHS0.8 ns 15
Address and control input pulse width (for each input) tIPW 2.2 ns
Address and control input setup time (fast slew rate) tISF0.75 ns
Address and control input setup time (slow slew rate) tISS0.8 ns 15
Data-out Low-Z window from CK/CK# tLZ –0.7 ns 19, 43
LOAD MODE REGISTER command cycle time tMRD 12 ns
DQ-DQS hold, DQS to first DQ to go non-valid, per access tQH tHP -tQHS ns 26, 27
Data hold skew factor tQHS 0.55 ns
ACTIVE-to-READ with auto precharge command tRAP 15 ns
ACTIVE-to-PRECHARGE command tRAS 42 7 0,000 ns 36, 54
ACTIVE-to-ACTIVE/AUTO REFRESH command period tRC 60 ns 55
ACTIVE-to-READ or WRITE delay tRCD 15 ns
REFRESH-to-REFRESH command interval tREFC 70.3 µs 24
Average periodic refresh interval tREFI 7.8 µs 24
AUTO REFRESH command period tRFC 72 ns 50
PRECHARGE command period tRP 15 ns
DQS read preamble tRPRE 0.9 1.1 tCK 44
DQS read postamble tRPST 0.4 0.6 tCK 44
ACTIVE bank a to ACTIVE bank b command tRRD 12 ns
Terminating voltage delay to VSS tVTD 0 ns
DQS write preamble tWPRE 0.25 tCK
DQS write preamble setup time tWPRES 0 ns 21, 22
DQS write postamble tWPST 0.4 0.6 tCK 20
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 28 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Write recovery time tWR 15 ns
Internal WRITE-to-READ command delay tWTR 1 tCK
Exit SELF REFRESH-to-non-READ command tXSNR 75 ns
Exit SELF REFRESH-to-READ command tXSRD 200 tCK
Data valid output window n/a tQH - tDQSQ ns 26
Table 12: Electrical Characteristics and Recommended AC Operating Conditions (-6T) (continued)
Notes: 1–6, 16–18, and 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -6T (TSOP)
Units NotesParameter Symbol Min Max
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 29 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 13: Electrical Characteristics and Recommended AC Operating Conditions (-75E)
Notes: 1–6, 16–18, 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -75E
Units NotesParameter Symbol Min Max
Access window of DQ from CK/CK# tAC –0.75 0.75 ns
CK high-level width tCH 0.45 0.55 tCK 31
Clock cycle time CL = 2.5 tCK (2.5) 7.5 13 ns 46, 52
CL = 2 tCK (2) 7.5 13 ns 46, 52
CK low-level width tCL 0.45 0.55 tCK 31
DQ and DM input hold time relative to DQS tDH 0.5 ns 27, 32
DQ and DM input pu lse width (for eac h input) tDIPW 1.75 ns 32
Access window of DQS from CK/CK# tDQSCK –0.75 0.75 ns
DQS input high pulse width tDQSH 0.35 tCK
DQS input low pulse width tDQSL 0.35 tCK
DQS–DQ skew, DQS to last DQ valid, per group, per access tDQSQ 0.5 ns 26, 27
WRITE command to first DQS latching transition tDQSS 0.75 1.25 tCK
DQ and DM input setup time relative to DQS tDS 0.5 ns 27, 32
DQS falling edge from CK rising - hold time tDSH 0.2 tCK
DQS falling edge to CK rising - setup time tDSS 0.2 tCK
Half-clock period tHP tCH,
tCL –ns35
Data-out High-Z window from CK/CK# tHZ 0.75 ns 19, 43
Address and control input hold time (fast slew rate) tIHF0.90 ns
Address and control input hold time (slow slew rate) tIHS1–ns15
Address and control input pulse width (for each input) tIPW 2.2 ns
Address and control input setup time (fast slew rate) tISF0.90 ns
Address and control input setup time (slow slew rate) tISS1–ns15
Data-out Low-Z window from CK/CK# tLZ –0.75 ns 19, 43
LOAD MODE REGISTER command cycle time tMRD 15 ns
DQ-DQS hold, DQS to first DQ to go non-valid, per access tQH tHP -tQHS ns 26, 27
Data hold skew factor tQHS 0.75 ns
ACTIVE-to-READ with auto precharge command tRAP 15 ns
ACTIVE-to-PRECHARGE command tRAS 40 120,000 ns 36, 54
ACTIVE-to-ACTIVE/AUTO REFRESH command period tRC 60 ns 55
ACTIVE-to-READ or WRITE delay tRCD 15 ns
REFRESH-to-REFRESH command interval tREFC 70.3 µs 24
Average periodic refresh interval tREFI 7.8 µs 24
AUTO REFRESH command period tRFC 75 ns 50
PRECHARGE command period tRP 15 ns
DQS read preamble tRPRE 0.9 1.1 tCK 44
DQS read postamble tRPST 0.4 0.6 tCK 44
ACTIVE bank a to ACTIVE bank b command tRRD 15 ns
Terminating voltage delay to VSS tVTD 0 ns
DQS write preamble tWPRE 0.25 tCK
DQS write preamble setup time tWPRES 0 ns 21, 22
DQS write postamble tWPST 0.4 0.6 tCK 20
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 30 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Write recovery time tWR 15 ns
Internal WRITE-to-READ command delay tWTR 1 tCK
Exit SELF REFRESH-to-non-READ command tXSNR 75 ns
Exit SELF REFRESH-to-READ command tXSRD 200 tCK
Data valid output window n/a tQH - tDQSQ ns 26
Table 13: Electrical Characteristics and Recommended AC Operating Conditions (-75E) (continued)
Notes: 1–6, 16–18, 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -75E
Units NotesParameter Symbol Min Max
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 31 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 14: Electrical Characteristics and Recommended AC Operating Conditions (-75Z)
Notes: 1–6, 16–18, 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -75Z
Units NotesParameter Symbol Min Max
Access window of DQ from CK/CK# tAC –0.75 0.75 ns
CK high-level width tCH 0.45 0.55 tCK 31
Clock cycle time CL = 2.5 tCK (2.5) 7.5 13 ns 46
CL = 2 tCK (2) 7.5 13 ns 46
CK low-level width tCL 0.45 0.55 tCK 31
DQ and DM input hold time relative to DQS tDH 0.5 ns 27, 32
DQ and DM input pu lse width (for eac h input) tDIPW 1.75 ns 32
Access window of DQS from CK/CK# tDQSCK –0.75 0.75 ns
DQS input high pulse width tDQSH 0.35 tCK
DQS input low pulse width tDQSL 0.35 tCK
DQS–DQ skew, DQS to last DQ valid, per group, per access tDQSQ 0.5 ns 26, 27
WRITE command-to-first DQS latching transition tDQSS 0.75 1.25 tCK
DQ and DM input setup time relative to DQS tDS 0.5 ns 27, 32
DQS falling edge from CK rising – hold time tDSH 0.2 tCK
DQS falling edge to CK rising – setup time tDSS 0.2 tCK
Half-clock period tHP tCH,tCL ns 35
Data-out High-Z window from CK/CK# tHZ 0.75 ns 19, 43
Address and control input hold time (fast slew rate) tIHF0.90 ns
Address and control input hold time (slow slew rate) tIHS1–ns15
Address and control input pulse width (for each input) tIPW 2.2 ns
Address and control input setup time (fast slew rate) tISF0.90 ns
Address and control input setup time (slow slew rate) tISS1–ns15
Data-out Low-Z window from CK/CK# tLZ –0.75 ns 19, 43
LOAD MODE REGISTER command cycle time tMRD 15 ns
DQ–DQS hold, DQS to first DQ to go non-valid, per access tQH tHP -tQHS ns 26, 27
Data hold skew factor tQHS 0.75 ns
ACTIVE-to-READ with auto precharge command tRAP 20 ns
ACTIVE-to-PRECHARGE command tRAS 40 120,000 ns 36
ACTIVE-to-ACTIVE/AUTO REFRESH command period tRC 65 ns 55
ACTIVE-to-READ or WRITE delay tRCD 20 ns
REFRESH-to-REFRESH command interval tREFC 70.3 µs 24
Average periodic refresh interval tREFI 7.8 µs 24
AUTO REFRESH command period tRFC 75 ns 50
PRECHARGE command period tRP 20 ns
DQS read preamble tRPRE 0.9 1.1 tCK 44
DQS read postamble tRPST 0.4 0.6 tCK 44
ACTIVE bank a to ACTIVE bank b command tRRD 15 ns
Terminating voltage delay to VDD tVTD 0 ns
DQS write preamble tWPRE 0.25 tCK
DQS write preamble setup time tWPRES 0 ns 21, 22
DQS write postamble tWPST 0.4 0.6 tCK 20
Write recovery time tWR 15 ns
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 32 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Internal WRITE-to-READ command delay tWTR 1 tCK
Exit SELF REFRESH-to-non-READ command tXSNR 75 ns
Exit SELF REFRESH-to-READ command tXSRD 200 tCK
Data valid output window n/a tQH - tDQSQ ns 26
Table 14: Electrical Characteristics and Recommended AC Operating Conditions (-75Z) (continued)
Notes: 1–6, 16–18, 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -75Z
Units NotesParameter Symbol Min Max
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 33 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 15: Electrical Characteristics and Recommended AC Operating Conditions (-75)
Notes: 1–6, 16–18, and 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -75
Units NotesParameter Symbol Min Max
Access window of DQ from CK/CK# tAC –0.75 0.75 ns
CK high-level width tCH 0.45 0.55 tCK 31
Clock cycle time CL = 2.5 tCK (2.5) 7.5 13 ns 46
CL = 2 tCK (2) 10 13 ns 46
CK low-level width tCL 0.45 0.55 tCK 31
DQ and DM input hold time relative to DQS tDH 0.5 ns 27, 32
DQ and DM input pu lse width (for eac h input) tDIPW 1.75 ns 32
Access window of DQS from CK/CK# tDQSCK –0.75 0.75 ns
DQS input high pulse width tDQSH 0.35 tCK
DQS input low pulse width tDQSL 0.35 tCK
DQS–DQ skew, DQS to last DQ valid, per group, per access tDQSQ 0.5 ns 26, 27
WRITE command-to-first DQS latching transition tDQSS 0.75 1.25 tCK
DQ and DM input setup time relative to DQS tDS 0.5 ns 27, 32
DQS falling edge from CK rising – hold time tDSH 0.2 tCK
DQS falling edge to CK rising – setup time tDSS 0.2 tCK
Half-clock period tHP tCH,tCL ns 35
Data-out High-Z window from CK/CK# tHZ 0.75 ns 19, 43
Address and control input hold time (fast slew rate) tIHF0.90 ns
Address and control input hold time (slow slew rate) tIHS1–ns15
Address and control input pulse width (for each input) tIPW 2.2 ns
Address and control input setup time (fast slew rate) tISF0.90 ns
Address and control input setup time (slow slew rate) tISS1–ns15
Data-out Low-Z window from CK/CK# tLZ –0.75 ns 19, 43
LOAD MODE REGISTER command cycle time tMRD 15 ns
DQ–DQS hold, DQS to first DQ to go non-valid, per access tQH tHP -tQHS ns 26, 27
Data hold skew factor tQHS 0.75 ns
ACTIVE-to-READ with auto precharge command tRAP 20 ns
ACTIVE-to-PRECHARGE command tRAS 40 120,000 ns 36
ACTIVE-to-ACTIVE/AUTO REFRESH command period tRC 65 ns 55
ACTIVE-to-READ or WRITE delay tRCD 20 ns
REFRESH-to-REFRESH command interval tREFC 70.3 µs 24
Average periodic refresh interval tREFI 7.8 µs 24
AUTO REFRESH command period trFC 75 ns 50
PRECHARGE command period tRP 20 ns
DQS read preamble tRPRE 0.9 1.1 tCK 44
DQS read postamble tRPST 0.4 0.6 tCK 44
ACTIVE bank a to ACTIVE ban k b command tRRD 15 ns
Terminating voltage delay to VDD tVTD 0 ns
DQS write preamble tWPRE 0.25 tCK
DQS write preamble setup time tWPRES 0 ns 21, 22
DQS write postamble tWPST 0.4 0.6 tCK 20
Write recovery time tWR 15 ns
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 34 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Internal WRITE-to-READ command delay tWTR 1 tCK
Exit SELF REFRESH-to-non-READ command tXSNR 75 ns
Exit SELF REFRESH-to-READ command tXSRD 200 tCK
Data valid output window n/a tQH - tDQSQ ns 26
Table 16: Input Slew Rate Derating Values for Addresses and Commands
Note: 15 applies to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
Speed Slew Rate tIS tIH Units
-75Z/-75E 0.500 V/ns 1.00 1 ns
-75Z/-75E 0.400 V/ns 1.05 1 ns
-75Z/-75E 0.300 V/ns 1.10 1 ns
Table 17: Input Slew Rate Derating Values for DQ, DQS, and DM
Note: 32 applies to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
Speed Slew Rate tDS tDH Units
-75Z/-75E 0.500 V/ns 0.50 0.50 ns
-75Z/-75E 0.400 V/ns 0.55 0.55 ns
-75Z/-75E 0.300 V/ns 0.60 0.60 ns
Table 15: Electrical Characteristics and Recommended AC Operating Conditions (-75) (continued)
Notes: 1–6, 16–18, and 34 apply to the entire table; Notes appear on page 35;
0°C TA 70°C; VDDQ = 2.5V ±0.2V, VDD = 2.5V ±0.2V
AC Characteristics -75
Units NotesParameter Symbol Min Max
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 35 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Notes 1. All v o ltages referenced to VSS.
2. Tests for AC timing, IDD, and electrical AC and DC characteristics may be conducted
at nominal reference/supply voltage levels, but the related specifications and the
device operation are guaranteed for the full voltage range spec ified.
3. Outputs (except for IDD measurements) measured with equivalent load:
4. AC timing and IDD tests may use a VIL-to-VIH swing of up to 1.5V in the test environ-
ment, but input timing is still refer enced to VREF(or to the crossing point fo r CK/CK#),
and parameter specifications are guaranteed for the specified AC input levels under
normal use conditions. The minimum slew rate for the input signals used to test the
device is 1 V/ns in th e range be twe e n VIL(AC) and VIH(AC).
5. The AC and DC input level specifications are as defined in the SSTL_2 standard (that
is, the receiver will effectively switch as a result of the signal crossing the AC input
level and will remain in that state as long as the signal does not ring back above
[below] the DC input LOW [HIGH] level).
6. All speed grades are not offered on all densities. R efer to page 1 for availability.
7. VREF is expected to equal VDDQ/2 of the transmitting device and to track variations in
the DC level of the same. Peak-to-peak noise (noncommon mode) on VREF may not
exceed ±2% of the DC value. Thus, from VDDQ/2, VREF is allowed ±25mV for DC error
and an additional ±25mV for AC noise . This measur ement is to be taken at the nearest
VREF bypass capacitor.
8. VTT is not applied directly to the device. VTT is a system supply for signal termination
resistors, it is expected to be set equal to VREF
, and it must track variations in the DC
level of VREF
.
9. VID is the magnitude of the difference between the input level on CK and the input
level on CK#.
10. The value of VIX and VMP is expected to equal VDDQ/2 of the transmitting device and
must track variations in the DC level of th e sam e.
11. IDD is dependent on output loading and cycle ra tes. Specified values are obtained
with minimum cycle times at CL = 3 for -5B; CL = 2.5, -6/-6T/-75; and CL = 2,
-75E/-75Z speeds with the outputs open.
12. Enables on-chip refresh and address counters.
13. IDD specifications are tested after the device is properly initialized and is averaged at
the defined cycle rate.
14. This parameter is sampled. VDD = 2.5V ±0.2V, VDDQ = 2.5V ±0.2V, VREF =V
SS,
f=100MHz, T
A=25°C, V
OUT(DC) =V
DDQ/2, VOUT (peak-to-peak) = 0.2V. DM input is
grouped with I/O pins, reflecting the fact that they are matched in loading.
15. For slew rates le ss than 1 V/ns and greater than or equal to 0.5 V/ns. If the slew rate is
less than 0.5 V/ns, timing must be derated: tIS has an additional 50ps per each
100 mV/ns reduction in slew rate from the 500 mV/ns. tIH has 0ps added, that is, it
remai ns constant. If the slew rate ex ceeds 4.5 V/ns , functionality is uncertain. F or -5B ,
-6, and -6T, slew rates must be gr eater than or equal to 0.5 V/ns.
Output
(VOUT)Reference
point
50
VTT
30pF
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 36 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
16. The CK/CK# input reference level (for timing refere nced to CK/CK#) is the point at
which CK and CK# cross; the input reference level for signals other than CK/CK# is
VREF
.
17. I nputs ar e not r e cognized as valid until VREF stabilizes. Once initialized, including self
refresh mode, VREF must be powered within specified range. Exception: during the
period before VREF stabilizes, CKE < 0.3 × VDD is recognized as LOW.
18. The output timing reference level, as measured at the timing refere nc e point (indi-
cated in Note 3), is VTT.
19. tHZ and tLZ transitions occur in the same access time windows as data valid transi-
tions. These parameters are not referenced to a specific voltage level, but specify
when the device output is no longer driving (High-Z) or begins driving (Low-Z).
20. The intent of the “Dont Care” state after completion of the postamble is the DQS-
driven signal should either be HIGH, LOW, or High-Z, and that any signal transition
within the input switch ing region must follow valid input requirements. That is, if
DQS transitions HIGH (above VIH(DC)min) then it must not transition LOW (below
VIH(DC) prior to tDQSH [MIN]).
21. This is not a device limit. The device will operate with a negative value, but system
performance could be degraded due to bus turnaround.
22. It is r ecommended that DQS be valid (HIGH or LOW) on or before the WRITE com-
mand. The case shown (DQS going from High-Z to logic LOW) applies when no
WRITEs were previously in progress on the bus. If a previous WRITE was in progress,
DQS could be HIGH during this time, depending on tDQSS.
23. MIN (tRC or tRFC) for IDD measurements is the smallest multiple of tCK that meets
the minimum absolute value for the respectiv e parameter. tRAS (MAX) for IDD mea-
surem ents is the largest multiple of tCK that meets the maximum absolute value for
tRAS.
24. The refresh period is 64ms. This equates to an average re fresh rate of 7.8125µs. How-
ever, an AUTO REFRESH command must be asserted at least once every 70.3µs; burst
refreshing or posting by the DRAM contro ller greater than 8 REFRESH cycles is not
allowed.
25. The I/O capacitance per DQS and DQ byte/group will not differ by more than this
maximum amount for any given device.
26. The data valid window is derived by achieving other specifications: tHP (tCK/2),
tDQSQ, and tQH (tQH = tHP- tQHS). The data valid window derates in direct propor-
tion to the clock duty cycle and a practical data valid window can be derived. The
clock is allowed a maximum duty cycle variation of 45/55, because functiona lity is
uncertain when operating beyond a 45/55 ratio. The data valid window derating
curves are provided in Figure 3 on page 37 for duty cycles ranging betwe en 50/50 and
45/55.
27. Referenced to each output group: x4= DQS with DQ[3:0]; x8 = DQS with DQ[7:0];
x16 = LDQS with DQ[7:0] and UDQS with DQ[15:8].
28. This limit is actually a nominal value and does not result in a fail value. CKE is HIGH
during the REFRESH command period (tRFC [MIN]), else CKE is LOW (that is, during
standby).
29. To maintain a valid level, the transitionin g e dg e of the input mus t:
29a. Sustain a constant slew rate from the current AC level through to the target AC
level, VIL(AC) or VIH(AC).
29b. Reach at least the target AC level.
29c. After the AC target level is reached, continue to maintain at least the target DC
level, VIL(DC) or VIH(DC).
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 37 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
30. The input capacitance per pin group will not differ by more than thi s maximum
amount for any given device.
31. CK and CK# input slew rate must be 1V/ns (2 V/ns if measured differentially).
Figure 3: Derating Data Va lid Window (tQH – tDQSQ)
32. DQ and DM input slew r ates must not deviate from DQS b y mor e than 10%. If the DQ/
DM/DQS slew rate is less than 0.5 V/ns, timing must be derated: 50ps must be added
to tDS and tDH for each 100 mV/ns reduction in slew rate. For -5B, -6, and
-6T speed grades, the slew rate must be 0.5V/ns. If the slew rate exceeds 4 V/ns,
functionality is uncertain.
33. VDD must not vary more than 4% if CKE is not active while any bank is active.
34. The clock is allowed up to ±150ps of jitter. Each timing parameter is allowed to vary by
the same amount.
35. tHP (MIN) is the lesser of tCL (MIN) and tCH (MIN) actually applied to the device CK
and CK# inputs, collectively, during bank active.
36. READs and WRITEs with auto pr echar ge ar e not all o wed to be issued until tRAS (MIN)
can be satisfied prior to the internal PRECHARGE command being issued.
37. Any positive glitch must be less than 1/3 of the clock cycle and not more than 400mV
or 2.9V (300mV or 2.9V maximum for -5B), whi chever is l ess . Any neg ativ e glitch must
be less than 1/3 of the clock cy cle and not ex ceed either 300mV or 2.2V (2.4V for -5B),
whichever is more positive. The average cann ot be below the 2.5V (2.6V for -5B) mini-
mum.
38. Nor mal outp ut dr ive curves:
38a. The full driver pull-down current variation from MIN to MAX process; tempera-
ture and voltage will lie within the outer bounding lines of the V-I curve of
Figure 4 on page 38.
38b. The driver pull-down current variation, within nominal voltage and temperature
limits, is expected, but not guaranteed, to lie within the inner bounding lines of
the V-I curve of Figure 4 on page 38.
3.0ns
2.5ns
2.0ns
1.5ns
1.0ns 50/50 49/51 48/53 46/54 47/53 45/55
-6T @ tCK = 7.5ns
-75E / -75 @ tCK = 7.5ns
-6 @ tCK = 6ns
-6T @ tCK = 6ns
-5B @ tCK = 5ns
1.48 1.45 1.43 1.40 1.38 1.35
2.75
2.60 2.56 2.53 2.45 2.41 2.38
2.68
2.35 2.31 2.28
2.13
2.20 2.16
2.43
2.10 2.07 2.04
1.89 1.86 1.83 1.80
1.98 1.95
2.00 1.97 1.94 1.91 1.88
1.73 1.70
1.82 1.79
1.58 1.55
Clock Dut
y
C
y
cle
Data Valid Window
2.71
2.46
1.53
2.64
2.39
1.92
1.76
1.85
1.60
1.50
2.49
2.50
2.24
2.01
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 38 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
38c. The full driver pull-up current variation from MIN to MAX process; temperature
and voltage will lie within the outer bounding lines of the V-I curve of Figure5 on
page 38.
38d. The driver pull-up current variation within nominal limits of voltage and temper-
ature is expected, but not guaranteed, to lie within the inner bounding lines of the
V-I curve of Figure5 on page 38.
38e. The full ratio variation of MAX to MIN pull-up and pull-down current should be
between 0.71 and 1.4 for drain-to-source voltages from 0.1V to 1.0V at the same
voltage and temperature.
38f. The full ratio variation of the nominal pull-up to pull-down current should be
unity ±10% for device drain-to-source voltages from 0.1V to 1.0V.
Figure 4: Full Drive Pull-Down Characteristics
Figure 5: Full Drive Pull-Up Characteristics
39. Reduced output drive curves:
39a. The full driver pull-down current variation from MIN to MAX process; tempera-
ture and voltage will lie within the outer bounding lines of the V-I curve of
Figure 6 on page 39.
39b. The driver pull-down current variation, within nominal voltage and temperature
limits, is expected, but not guaranteed, to lie within the inner bounding lines of
the V-I curve of Figure 6 on page 39.
39c. The full driver pull-up current variation from MIN to MAX process; temperature
and voltage will lie within the outer bounding lines of the V-I curve of Figure 7.
-200
-180
-160
-140
-120
-100
-80
-60
-40
-20
0
0.0 0.5 1.0 1.5 2.0 2.5
I
OUT
(mA)
V
DDQ
- V
OUT
(V)
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 39 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
39d. The driver pull-up current variation, within nominal voltage and temperature
limits, is expected, but not guaranteed, to lie within the inner bounding lines of
the V-I curve of Figure 7 on page 39.
39e. The full ratio variation of the MAX-to-MIN pull- up and pull-down current should
be between 0.71 and 1.4 for device drain-to-source voltages from 0.1V to 1.0V at
the same voltage and temperature.
39f. The full ratio variation of the nominal pull-up to pull-down current should be
unity ±10%, for device drain-to-source voltages from 0.1V to 1.0V.
Figure 6: Reduced Drive Pull-Down Characteristics
Figure 7: Reduced Drive Pull-Up Characteristics
40. The voltage levels used are derived from a minimum VDD level and the refer enced test
load. In practice, the voltage levels obtained from a properly terminated bus will pro-
vide significantly different voltage values.
41. VIH overshoot: VIH,max =V
DDQ+1.5V for a pulse width 3ns, and the pulse width
can not be greater than 1/3 of the cycle rate . VIL undershoot: VIL,min =1.5V for a pulse
width 3ns, and the pulse width can not be greater than 1/3 of the cycle rate.
42. VDD and VDDQ must track each other.
43. tHZ (MAX) will prevail over tDQSCK (MAX) + tRPST (MAX) condition. tLZ (MIN) will
prevail over tDQSCK (MIN) + tRPRE (MAX) condition.
0
10
20
30
40
50
60
70
80
0.00.51.01.5
2.0 2.5
I
OUT
(mA)
V
OUT
(V)
-80
-70
-60
-50
-40
-30
-20
-10
0
0.0 0.5 1.0 1.5 2.0 2.5
I
OUT
(mA)
V
DDQ
- V
OUT
(V)
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 40 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
44. tRPST end point and tRPRE begin point are not re ferenced to a specific voltage level
but specify when the device output is no longer driving (tRPST) or begins driving
(tRPRE).
45. During initialization, VDDQ, VTT, and VREF must be equal to or less than VDD + 0.3V.
Alternatively, VTT may be 1.35V maximum during power -up, even if VDD/VDDQ are 0V,
provided a minimum of 42 of series resistance is used between the VTT supply and
the input pin.
46. The current Micron part operates below 83 MHz (slowest specified JEDEC operating
frequency). As such, future die may not reflect this option.
47. When an input signal is HIGH or LOW, it is defined as a steady state logic HIGH or
LOW.
48. Random address is changing; 50% of data is changing at every transfer.
49. Random address is changing; 100% of data is changing at every transfer.
50. CKE must be active (HIGH) during the entire time a REFRESH command is executed.
That is, from the time the AUTO REFRESH command is regi stered, CKE must be
active at each rising clock edge, until tRFC has been satisfied.
51. IDD2N specifies the DQ, DQS, and DM to be driven to a val id HIGH or LOW logic level.
IDD2Q is similar to IDD2F except IDD2Q specifies the address and control inputs to
remain stable. Although IDD2F
, IDD2N, and IDD2Q are similar, IDD2F is “worst case.
52. Whenever the operating frequency is altered, not including jitter, the DLL is required
to be reset followed by 200 clock cycles before any READ command.
53. This is the DC voltage supplied at the DRAM and is inclusive of all noise up to 20 MHz.
Any noise above 20 MHz at the DRAM generated from any source other than that of
the DRAM itself may not exceed the DC voltage range of 2.6V ±100mV.
54. The -6/-6T speed grades will operate with tRAS (MIN) = 40ns and
tRAS ( MAX) = 120,000ns at any slower frequency.
55. DRAM devices should be evenly addressed when being acces se d. Disproportio nate
accesses to a particular row addr ess may result in reduction of the product lifetime.
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 41 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 18: Normal Output Dri ve Characteristics
Characteristics are specified under best, worst, and nominal process variation/conditions
Voltage
(V)
Pull-Down Current (mA) Pull-Up Current (mA)
Nominal
Low Nominal
High Min Max Nominal
Low Nominal
High Min Max
0.1 6.0 6.8 4.6 9.6 –6.1 –7.6 –4.6 –10.0
0.2 12.2 13.5 9.2 18.2 –12.2 14.5 –9.2 –20.0
0.3 18.1 20.1 13.8 26.0 –18.1 –21.2 –13.8 –29.8
0.4 24.1 26.6 18.4 33.9 –24.0 –27.7 –18.4 –38.8
0.5 29.8 33.0 23.0 41.8 –29.8 –34.1 –23.0 –46.8
0.6 34.6 39.1 27.7 49.4 –34.3 –40.5 –27.7 –54.4
0.7 39.4 44.2 32.2 56.8 –38.1 –46.9 –32.2 –61.8
0.8 43.7 49.8 36.8 63.2 –41.1 –53.1 –36.0 –69.5
0.9 47.5 55.2 39.6 69.9 –43.8 –59.4 –38.2 –77.3
1.0 51.3 60.3 42.6 76.3 –46.0 –65.5 –38.7 –85.2
1.1 54.1 65.2 44.8 82.5 –47.8 –71.6 –39.0 –93.0
1.2 56.2 69.9 46.2 88.3 –49.2 –77.6 –39.2 –100.6
1.3 57.9 74.2 47.1 93.8 –50.0 –83.6 –39.4 –108.1
1.4 59.3 78.4 47.4 99.1 –50.5 –89.7 –39.6 –115.5
1.5 60.1 82.3 47.7 103.8 –50.7 –95.5 –39.9 –123.0
1.6 60.5 85.9 48.0 108.4 51.0 –101.3 –40.1 –130.4
1.7 61.0 89.1 48.4 112.1 51.1 –107.1 –40.2 –136.7
1.8 61.5 92.2 48.9 115.9 51.3 –112.4 –40.3 –144.2
1.9 62.0 95.3 49.1 119.6 51.5 –118.7 –40.4 –150.5
2.0 62.5 97.2 49.4 123.3 51.6 –124.0 –40.5 –156.9
2.1 62.8 99.1 49.6 126.5 51.8 –129.3 –40.6 –163.2
2.2 63.3 100.9 49.8 129.5 –52.0 –134.6 –40.7 –169.6
2.3 63.8 101.9 49.9 132.4 –52.2 –139.9 –40.8 –176.0
2.4 64.1 102.8 50.0 135.0 –52.3 –145.2 –40.9 –181.3
2.5 64.6 103.8 50.2 137.3 –52.5 –150.5 –41.0 –187.6
2.6 64.8 104.6 50.4 139.2 –52.7 –155.3 –41.1 –192.9
2.7 65.0 105.4 50.5 140.8 –52.8 –160.1 –41.2 –198.2
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 42 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Electrical Specifications – DC and AC
Table 19: Reduced Output Drive Characteristics
Characteristics are specified under best, worst, and nominal process variation/conditions
Voltage
(V)
Pull-Down Current (mA) Pull-Up Current (mA)
Nominal
Low Nominal
High Min Max Nominal
Low Nominal
High Min Max
0.1 3.4 3.8 2.6 5.0 –3.5 –4.3 –2.6 –5.0
0.2 6.9 7.6 5.2 9.9 –6.9 –7.8 –5.2 –9.9
0.3 10.3 11.4 7.8 14.6 –10.3 12.0 –7.8 –14.6
0.4 13.6 15.1 10.4 19.2 –13.6 –15.7 –10.4 –19.2
0.5 16.9 18.7 13.0 23.6 –16.9 –19.3 –13.0 –23.6
0.6 19.9 22.1 15.7 28.0 –19.4 –22.9 –15.7 –28.0
0.7 22.3 25.0 18.2 32.2 –21.5 –26.5 –18.2 –32.2
0.8 24.7 28.2 20.8 35.8 –23.3 –30.1 –20.4 –35.8
0.9 26.9 31.3 22.4 39.5 –24.8 –33.6 –21.6 –39.5
1.0 29.0 34.1 24.1 43.2 –26.0 –37.1 –21.9 –43.2
1.1 30.6 36.9 25.4 46.7 –27.1 –40.3 –22.1 –46.7
1.2 31.8 39.5 26.2 50.0 –27.8 –43.1 –22.2 –50.0
1.3 32.8 42.0 26.6 53.1 –28.3 –45.8 –22.3 –53.1
1.4 33.5 44.4 26.8 56.1 –28.6 –48.4 –22.4 –56.1
1.5 34.0 46.6 27.0 58.7 –28.7 –50.7 –22.6 –58.7
1.6 34.3 48.6 27.2 61.4 –28.9 –52.9 –22.7 –61.4
1.7 34.5 50.5 27.4 63.5 –28.9 –55.0 –22.7 –63.5
1.8 34.8 52.2 27.7 65.6 –29.0 –56.8 –22.8 –65.6
1.9 35.1 53.9 27.8 67.7 –29.2 –58.7 –22.9 –67.7
2.0 35.4 55.0 28.0 69.8 –29.2 –60.0 –22.9 –69.8
2.1 35.6 56.1 28.1 71.6 –29.3 –61.2 –23.0 –71.6
2.2 35.8 57.1 28.2 73.3 –29.5 –62.4 –23.0 –73.3
2.3 36.1 57.7 28.3 74.9 –29.5 –63.1 –23.1 –74.9
2.4 36.3 58.2 28.3 76.4 –29.6 –63.8 –23.2 –76.4
2.5 36.5 58.7 28.4 77.7 –29.7 –64.4 –23.2 –77.7
2.6 36.7 59.2 28.5 78.8 –29.8 –65.1 –23.3 –78.8
2.7 36.8 59.6 28.6 79.7 –29.9 –65.8 –23.3 –79.7
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 43 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
Commands Tables 20 and 21 provide a quick r e fer ence of available commands. Two additional Truth
Tables—Table 22 on page 44 and Table 23 on page 45—provide current state/next state
information.
Notes: 1. DESELECT and NOP are functionally intercha ngeabl e.
2. BA[1:0] provide bank address and A[n:0] (128Mb: n = 11; 256Mb and 512Mb: n = 12; 1Gb: n
= 13) provide row address.
3. BA[1:0] provide bank address; A[i:0] provide column address, (where Ai is the most signifi-
cant column address bit for a given density and configuration, see Table 2 on page 2) A10
HIGH enables the auto precharge feature (non persistent), and A10 LOW disables the auto
precharge feature.
4. Applies only to READ bursts with auto pre charg e di sable d; th is com mand is und efine d (an d
should not be used) for READ bursts with auto precharge enabled and for WRITE bursts.
5. A10 LOW : BA[1:0] determine which bank is precharged. A10 HIGH: all banks are precharged
and BA[1:0] are “Don’t Care.”
6. This command is AUTO REFRESH if CKE is HIGH; SELF REFRESH if CKE is LOW.
7. Internal refresh counter controls row addressing while in self refresh mode, all inputs and
I/Os are “Don’t Care” except for CKE.
8. BA[1:0] select either the mode register or the extended mode register (BA0 = 0, BA1 = 0
select the mode register; BA0 = 1, BA1 = 0 select extended mode register; other combina-
tions of BA[1:0] are reserved). A[n:0] provide the op-code to be written to the selected
mode register.
Table 20: Truth Table 1 – Commands
CKE is HIGH for all commands shown except SELF REFRESH; All states and sequences not shown are illegal or
reserved
Function CS# RAS# CAS# WE# Address Notes
DESELECT HXXX X 1
NO OPERATION (NOP) LHHH X 1
ACTIVE (select bank and activate row) L L H H Bank/row 2
READ (select bank and column and start READ burst) L H L H Bank/col 3
WRITE (select bank and column and start WRITE burst) L H L L Bank/col 3
BURST TERMINATE LHHL X 4
PRECHARGE (deactivate row in bank or banks) L L H L Code 5
AUTO REFRESH or SELF REFRESH
(enter self refresh mode) LLLH X6, 7
LOAD MODE REGISTER LLLLOp-code8
Table 21: Truth Table 2 – DM Operation
Used to mask write data, provided coincident wit h the correspond ing data
Name (Function) DM DQ
Write enable L Valid
Write inhibit H X
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 44 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
Notes: 1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Table 25 on page 47) and
after tXSNR has been met (if the previous state was self refresh).
2. This table is bank-specific, except where noted (that is, the current state is for a specific
bank and the commands shown are those allowed to be issued to that bank when in that
state). Exceptions are covered in the notes below.
3. Current state definitions:
Idle: The bank has been precharged, and tRP has been met.
Row active: A row in the bank has been activated, and tRCD has been met. No data
bursts/accesses and no register accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabl ed , an d has no t yet
terminated or been terminated.
Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet
terminated or been terminated.
4. The following states must not be interrupted by a command issued to the same bank. COM-
MAND INHIBIT or NOP commands, or allowable commands to the other bank should be
issued on any clock edge occurring during these states. Allowable commands to the other
bank are determi ned by its current st ate and Table 22 and according to Table 23 on
page 45.
Precharging: Starts with registration of a PRECHARGE command and ends when tRP is
met. Once tRP is met, the bank will be in the idle state.
Row activating: Starts with registration of an ACTIVE command and ends when tRCD is
met. Once tRCD is met, the bank will be in the “row active” state.
Read with aut o pr e ch ar ge enabled : Starts with registration of a READ command with
auto precharge enabled an d ends when tRP has been met. Once tRP is met, the bank
will be in the idle state.
Write with auto precharge enabled: Starts with registration of a WRITE command with
auto precharge enabled an d ends when tRP has been met. Once tRP is met, the bank
will be in the idle state.
5. The following states must not be interrupted by any executable command; COMMAND
INHIBIT or NOP commands must be applied on each positive clock edge during these states.
Table 22: Truth Table 3 – Current State Bank n – Command to Bank n
Notes: 1–6 apply to the entire table; Notes appear below
Current State CS# RAS# CAS# WE# Command/Action Notes
Any HXXX
DESELECT (NOP/continue previo us operation)
LHHH
NO OPERATION (N OP/continue previous operati on)
Idle LLHH
ACTIVE (select and activate row)
LLLH
AUTO REFRESH 7
LLLL
LOAD MODE REGISTER 7
Row active LHLH
READ (select column and start READ burst) 10
LHLL
WRITE (select column and start WRITE burst) 10
LLHL
PRECHARGE (deactivate row in bank or banks) 8
Read
(auto precharge
disabled)
LHLH
READ (select column and start new READ burst) 10
LHLL
WRITE (select column and start WRITE burst) 10, 12
LLHL
PRECHARGE (truncate READ burst, start PRECHARGE) 8
LHHL
BURST TER MINATE 9
Write
(auto precharge
disabled)
LHLH
READ (select column and start READ burst) 10, 11
LHLL
WRITE (select column and start new WRITE burst) 10
LLHL
PRECHARGE (truncate WRITE burst, start
PRECHARGE) 8, 11
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 45 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRFC
is met. After tRFC is met, the DDR SDRAM will be in the all banks idle state.
Accessing mode register: Starts with registration of an LMR command and ends wh en
tMRD has been met. After tMRD is met, the DDR SDRAM will be in the all banks idle
state.
Precharging all: Starts with registration of a PRECHARGE ALL command and ends when
tRP is met. After tRP is met, all banks will be in the idle state.
6. All states and sequences not shown are illegal or reserved.
7. Not bank-specific; requires that all banks are idle, and bursts are not in progress.
8. May or may not be bank-specific; if multiple banks are to be precharged, each must be in a
valid state for precharging.
9. Not bank-specific; BURST TERMINATE affects the most recent READ burst, regardless of
bank.
10. READs or WRITEs listed in the Command/Actio n column include READs or WRITEs with auto
precharge enabled and READs or WRITEs with auto precharge disabled.
11. Requires appropriate DM masking.
12. A WRITE command may be applied after the completion of the READ burst; otherwise, a
BURST TERMINATE must be used to end the READ burst prior to asserting a WRITE com-
mand.
Notes: 1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Table 25 on page 47) and
after tXSNR has been met (if the previous state was self refresh).
Table 23: Truth Table 4 – Current State Bank n – Command to Bank m
Notes: 1–6 apply to the entire table; Notes ap pear on page 45
Current State CS# RAS# CAS# WE# Command/Action Notes
Any HXXX
DESELECT (NOP/continue previo us operation)
LHHH
NO OPERATION (N OP/continue previous operati on)
Idle XXXX
Any command otherw ise allowed to bank m
Row activating, active,
or precharging LLHH
ACTIVE (select and activate row)
LHLH
READ (select column and start READ burst) 7
LHLL
WRITE (select column and start WRITE burst) 7
LLHL
PRECHARGE
Read (auto precharge
disabled) LLHH
ACTIVE (select and activate row)
LHLH
READ (select column and start new READ burst) 7
LHLL
WRITE (select column and start WRITE burst) 7, 9
LLHL
PRECHARGE
Write (auto precharge
disabled) LLHH
ACTIVE (select and activate row)
LHLH
READ (select column and start READ burst) 7, 8
LHLL
WRITE (select column and start new WRITE burst) 7
LLHL
PRECHARGE
Read (with auto-
precharge) LLHH
ACTIVE (select and activate row)
LHLH
READ (select column and start new READ burst) 7
LHLL
WRITE (select column and start WRITE burst) 7, 9
LLHL
PRECHARGE
Write (with auto-
precharge) LLHH
ACTIVE (select and activate row)
LHLH
READ (select column and start READ burst) 7
LHLL
WRITE (select column and start new WRITE burst) 7
LLHL
PRECHARGE
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 46 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
2. This table describes alternate bank operation, except where noted (that is, the current state
is for bank n, and the commands shown are those allowed to be issued to bank m, assuming
that bank m is in such a state that the given command is allowable). Exceptions are covered
in the notes below.
3. Current state definitions:
Idle: The bank has been precharged, and tRP has been met.
Row active: A row in the bank has been activated, and tRCD has been met. No data
bursts/accesses and no register accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabl ed , an d has no t yet
terminated or been terminated.
Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet
terminated or been terminated.
Read with auto precharge enabled: See note 3a below.
Write with auto precharge enabled: See note 3a below.
a. The read with auto precharge enabled or write with auto precharge enabled states
can each be broken into two parts: the access period and the precharge period. For
read with auto precharge, the precharge period is defined as if the same burst was
executed with auto precharge disabled and then followed with the earliest possible
PRECHARGE command that still accesses all of the data in the burst. For write with
auto precharge, the precharge period begins when tWR ends, with tWR measured as
if auto precharge was disabled. The access period starts with registration of the com-
mand and ends where the precharge period (or tRP) beg ins. This device supports
concurrent auto precharge such that when a read with auto precharge is enabled or
a write with auto precharge is enabled, any command to other banks is allowed, as
long as that command does not interrupt the read or write data transfer already in
process. In either case, all other related limitations apply (for example, contention
between read data and write data must be avoided).
b. The minimum delay from a READ or WRITE command with auto precharge enabled,
to a command to a different bank is summarized in Table 24.
4. AUTO REFRESH and LMR commands may only be issued when all banks are idle.
5. A BURST TERMINATE command cannot be issued to another bank; it applies to the bank
represented by the current state only.
6. All states and sequences not shown are illegal or reserved.
7. READs or WRITEs listed in the “Command/Action” column include READs or WRITEs with
auto precharge enabled and READs or WRITEs with auto precharge disabled.
8. Requires appropriate DM masking.
9. A WRITE command may be applied after the completion of the READ burst; otherwise , a
BURST TERMINATE must be used to end the READ burst prior to asserting a WRITE com-
mand.
Table 24: Command Delays
CLRU = CL rounded up to the next integer
From
Command To Command Minimum Delay
with Concurrent Auto Precharge
WRITE with auto
precharge READ or READ with auto precharge [1 + (BL/2)] × tCK + tWTR
WRITE or WRITE with auto precharge (BL/2) × tCK
PRECHARGE 1 tCK
ACTIVE 1 tCK
READ with auto
precharge READ or READ with aut o precharge (BL/2) × tCK
WRITE or WRITE with auto precharge [CLRU + (BL/2)] × tCK
PRECHARGE 1 tCK
ACTIVE 1 tCK
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 47 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
Notes: 1. CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous
clock edge.
2. Current state is the state of the DDR SDRAM immediately prior to clock edge n.
3. COMMANDn is the command registered at clock edge n, and ACTIONn is a result of COM-
MANDn.
4. All states and sequences not shown are illegal or reserved.
5. CKE must not drop LOW during a column access. For a READ, this means CKE must stay
HIGH until after the read postamble time (tRPST); for a WRITE, CKE must stay HIGH until the
write recovery time (tWR) has been met.
6. Once initialized, including during self refresh mode, VREF must be powered within the spec-
ified range.
7. Upon exit of the self refresh mode, the DLL is automatically enabled. A minimum of 200
clock cycles is needed before applying a READ command for the DLL to lock. DESELECT or
NOP commands should be issued on any clock edges occurr ing during the tXSNR period.
DESELECT
The DESELECT function (CS# HIGH) prevents new commands from being executed by
the DDR SDRAM. The DDR SDRAM is effectivel y deselected. O per ations already in prog-
ress are not affected.
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to instruct the selected DDR SDRAM to
perform a NOP (CS# is LOW with RAS#, CAS#, and WE# are HIGH). This prevents
unwanted commands from be ing registered during id le or wait states. Operations
already in progress are not affected.
LOAD MODE REGISTER (LMR)
The mode registers are loaded via inputs A0–An (see "REGISTER DEFINITION" on page
55). The LMR command can only be issued when all banks are idle, and a subsequent
executable command cannot be issued until tMRD is met.
Table 25: Truth Table 5 – CKE
Notes 1–6 apply to the entire table; Notes appear below
CKEn-1 CKEnCurrent State CommandnActionnNotes
L L Power-down X Maintain power-down
Self refresh X Maintain self refres h
L H Power-down DESELECT or NOP Exit power-down
Self refresh DESELECT or NOP Exit self refresh 7
H L All banks idle DESELECT or NOP Precharge power-down entry
Bank(s) active DESELECT or NOP Active power-down entry
All banks idle AUTO REFRESH Self refresh entry
H H See Table 20 on page 43
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 48 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
ACTIVE (ACT)
The ACTIVE command is used to open (or activate) a row in a particular bank for a
subsequent access, like a read or a write, as shown in Figure8. The value on the BA0, BA1
inputs selects the bank, and the address provided on inputs A[n:0] selects the row.
Figure 8: Activating a Specific Row in a Specific Bank
CS#
WE#
CAS#
RAS#
CKE
Address Row
HIGH
BA0, BA1 Bank
CK
CK#
Dont Care
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 49 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
READ
The READ command is used to initiate a burst read access to an active row, as shown in
Figure 9 on page 49. The value on the BA0, BA1 inputs selects the bank, and the address
pro vided on inputs A[i:0] (where Ai is the most signi ficant c olumn add r ess bit for a giv en
density and config uration, se e Table 2 on page 2) selects the starting column location.
Figure 9: READ Command
Note: EN AP = enable auto precharge; DISAP=disableautoprecharge.
CS#
WE#
CAS#
RAS#
CKE
Address
A10
BA0, BA1
HIGH
CK
CK#
Dont Care
Col
DIS AP
EN AP
Bank
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 50 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
WRITE
The WRITE command is used to initiate a burst write access to an active ro w as shown in
Figure 10. The value on the BA0, BA1 inputs selects the bank, and the address provided
on inputs A[i:0] (where Ai is the most significant column address bit for a given density
and configuration, see Table 2 on page 2) selects the starting column location.
Figure 10: WRITE Command
Note: EN AP = enable auto precharge; and DIS AP = disable auto precharge.
CS#
WE#
CAS#
RAS#
CKE
A10
BA0, BA1
HIGH
CK
CK#
Dont Care
Address Col
EN AP
DIS AP
Bank
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 51 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Commands
PRECHARGE (PRE)
The PRECHARGE command is used to deactivate the open row in a particular bank or
the open ro w in all b anks as sho wn in F igure11. The value on the BA0, BA1 i nputs selects
the bank, and the A10 input selects whether a single bank is precharged or whether all
banks are precharged.
Figure 11: PRECHARGE Command
Notes: 1. If A10 is HIGH, bank address becomes “Don’t Care.”
BURST TERMINATE (BST)
The BURST TERMINATE command is used to truncate READ bursts (with auto
precharge disabled). The most recently registered READ command pr ior to the BURST
TERMINATE command will be truncated, as shown in “Operations” on page 52. The
open page from which the READ burst was terminated remain s open.
AUTO REFRESH (AR)
AUTO REFRESH is used during normal operation of the DDR SDRAM and is analogous
to CAS#-before-RAS# (CBR) refresh in FPM/EDO DRAMs. This command is nonpersis-
tent, so it must be issued each time a refresh is required. All banks must be idle before an
AUTO REFRESH command is issued.
SELF REFRESH
The SELF REFRESH command can be used to retain data in the DDR SDRAM, even if the
rest of the system is powered down. The SELF REFRESH command is initiated like an
AUTO REFRESH command except CKE is disabled (LOW).
CS#
WE#
CAS#
RAS#
CKE
A10
BA0, BA1
HIGH
Address
CK
CK#
Dont Care
Bank1
All banks
One bank
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 52 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Operations
INITIALIZATION
Prior to normal operation, DDR SDRAMs must be powered up and initialized in a
predefined manner. Operational procedures, other than those specified, may result in
undefined operation.
To ensure device operation, the DRAM must be initialized as desc ribed in the following
steps:
1. S i multaneously apply power to VDD and VDDQ.
2. Apply VREF and then VTT po wer. VTT must be applied after VDDQ to avoid device latch-
up , whi ch may cause permanent damage to the devic e . Ex cept fo r CKE, i nputs are not
recognized as valid until after VREF is applied.
3. Assert and hold CKE at a LVCMOS logic LOW. Maintaining an LVCMOS LOW level on
CKE during power-up is required to ensure that the DQ and DQS outputs will be in
the High-Z state, where they will remain until driven in normal operation (by a read
access).
4. Provid e s tab le clock signals.
5. Wait at least 200µs.
6. Bring CKE HIGH, and provide at least one NOP or DESELECT command. At this
point, the CKE input changes from a LVCMOS input to a SSTL_2 input only and will
remain a SSTL_2 input unless a po wer cycle occurs.
7. Perform a PRECHARGE ALL command.
8. Wait at least tRP time; during this time NOPs or DESELECT commands must be given.
9. Usin g the LMR command, program the extended mode register (E0 = 0 to enable the
DLL and E1 = 0 for normal drive; or E1 = 1 for reduced drive and E2–En must be set to
0 [where n = most significant bit]).
10. Wa it at least tMRD time; only NOPs or DESELECT commands are allowed.
11. Using the LMR command, program the mode register to set operating parameters
and to reset the DLL. At least 200 clock cycles are required between a DLL reset and
any READ command.
12. Wa it at least tMRD time; only NOPs or DESELECT commands are allowed.
13. Issue a PRECHARGE ALL command.
14. Wa it at least tRP time; only NOPs or DESELECT commands are allowed.
15. Issue an AUTO REFRESH command. This may be moved prior to step 13.
16. Wa it at least tRFC time; only NOPs or DESELECT commands are allowed.
17. Issue an AUTO REFRESH command. This may be moved prior to step 13.
18. Wa it at least tRFC time; only NOPs or DESELECT commands are allowed.
19. Although not required by the Micron device, JEDEC requires an LMR command to
clear the DLL bit (set M8 = 0). If an LMR command is issued, the same operating
parameters should be utilized as in step 11.
20. Wa it at least tMRD time; only NOPs or DESELECT commands are supported.
21. At this point the DRAM is ready for any valid command. At least 200 clock cycles with
CKE HIGH are required between step 11 (DLL RESET) and any READ command.
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 53 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 12: INITIALIZATION Flow Diagram
V
DD
and V
DDQ
ramp
Apply V
REF
and V
TT
CKE must be LVCMOS LOW
Apply stable clocks
Bring CKE HIGH with a NOP command
Wait at least 200µs
PRECHARGE ALL
Assert NOP or DESELECT for
t
RP time
Configure extended mode register
Configure load mode register and reset DLL
Assert NOP or DESELECT for
t
MRD time
Assert NOP or DESELECT for
t
MRD time
PRECHARGE ALL
Issue AUTO REFRESH command
Assert NOP or DESELECT for
t
RFC time
Optional LMR command to clear DLL bit
Assert NOP or DESELECT for
t
MRD time
DRAM is ready for any valid command
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Assert NOP or DESELECT commands for
t
RFC
Issue AUTO REFRESH command
Assert NOP or DESELECT for
t
RP time
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 54 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 13: INITIALIZATION Timing Diagram
Notes: 1. VTT is not applied directly to the device; however, tVTD 0 to avoid device latch-up. VDDQ,
VTT, and VREF VDD + 0.3V. Alternatively, VTT may be 1.35V maximum during power-up,
even if VDD/VDDQ are 0V, provided a minimum of 42of series resistance is used between
the VTT supply and the input pin. Once in itialized , VREF must always be powered within the
specified range.
2. Although not required by the Mic ron device, JEDEC specifies issuing another LMR command
(A8 = 0) prior to activating any bank. If another LMR command is issued, the same, previ-
ously issued operating parameters must be used.
3. The two AUTO REFRESH commands at Td0 and Te0 may be applied following the LMR com-
mand at Ta0.
4. tMRD is required before any command can be applied (during MRD time only NOPs or
DESELECTs are allowed), and 200 cycles of CK are required before a READ command can be
issued.
5. While programming th e op erating para meters, reset the DLL with A8 = 1.
tVTD1
CKE LVCMOS
LOW level
DQ
BA0, BA1
200 cycles of CK4
Load extended
mode register Load mode
register5
tMRD tMRD tRP tRFC tRFC
tIS
Power-up: V
DD
and CK stable
T = 200µs
High-Z
tIH
DM
DQS High-Z
Address RA
A10 All banks
CK
CK#
tCH tCL
tCK
V
TT
1
V
REF
V
DD
V
DD
Q
Command LMRNOP PRELMR AR AR ACT2
tIS tIH
BA0 = 1
BA1 = 0
tIS tIH tIS tIH
BA0 = 0
BA1 = 0
tIS tIH
()()
()(
)
()(
)
(
)()
Code Code
tIS tIH
Code Code3
PRE
All banks
tIS tIH
T0 T1 Ta0 Tb0 Tc0 Td0 Te0 Tf0
()(
)
Don’t Care
BA
(
)(
)
()(
)
()(
)
(
)(
)
(
)(
)
(
)(
)
(
)()
(
)()
()()
()()
()(
)
()(
)
(
)(
)
(
)(
)
tRP
(
)()
()()
()()
()(
)
()()
()(
)
()()
()(
)
()()
()(
)
()()
()(
)
()()
()(
)
()()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
(
)()
()(
)
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
(
)()
()()
(
)()
()()
(
)()
()()
(
)()
()()
(
)()
()()
RA
Indicates A Break in
Time Scale
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 55 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
REGISTER DEFINITION
Mode Register
The mode register is used to define the specific DDR SDRAM mode of operation. This
definition includes the selection of a burst length, a burst type, a CAS latency, and an
operating mode, as shown in Figure 14. The mode register is progr a mmed via the LMR
command (with BA0=0 and BA1=0) and will retain the stored information until it is
programmed again or until the device loses power (ex cept for bit A8, which is self-
clearing).
Repr og r ammi ng the mode r e gister wil l not alter the contents of the memory, provi ded it
is performed correctly. The mode reg ister must be loaded (reloaded) when all banks are
idle and no bursts are in progress, and the controller m ust wai t the specifi ed tim e before
initiating the subsequent operation. Violating either of these requirements will result in
unspecified operation.
Mode r egister bits A[2:0] specify the burst length, A3 specifies the type of burst (sequen-
tial or interleaved), A[6:4] specify the CAS latency, and A[n:7] specify the operating
mode.
Figure 14: Mode Register Definition
Notes: 1. n is the most significant row address bit from Table 2 on page 2.
Burst Type
Sequential
Interleaved
CAS Latency
Reserved
Reserved
2
3 (-5B only)
Reserved
Reserved
2.5
Reserved
Burst lengthCAS Latency BT0
A9 A7 A6 A5 A4 A3A8 A2 A1 A0
Mode register
(Mx)
Address bus
9765438210
M3
0
1
M4
0
1
0
1
0
1
0
1
M5
0
0
1
1
0
0
1
1
M6
0
0
0
0
1
1
1
1
Operating mode
. . .AnBA0BA1
. . .
n1
n + 1
0
n + 2
Operating Mode
Normal operation
Normal operation/reset DLL
All other states reserved
M8
0
1
M9
0
0
. . .
0
0
Mn
0
0
M7
0
0
M6–M0
Valid
Valid
Burst Length
Reserved
2
4
8
Reserved
Reserved
Reserved
Reserved
M0
0
1
0
1
0
1
0
1
M1
0
0
1
1
0
0
1
1
M2
0
0
0
0
1
1
1
1
Mn + 1
0
1
0
1
Mode Register Definition
Base mode register
Extended mode register
Reserved
Reserved
Mn + 2
0
0
1
1
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 56 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Burst Length (BL)
Read and write accesses to the DDR SDRAM are burst oriented, with the burst length
being programmable for both READ and WRITE bursts, as shown in Figure 14 on
page 55 . The burst lengt h determines the maximum number of column locations that
can be accessed for a given READ or WRITE command. BL = 2, BL = 4, or BL = 8 locations
are available for both the sequential and the interleaved burst types . Reserved states
should not be used, as unknown operation or incompatibility with future versions may
result.
When a READ or WRITE comm and is issu ed , a block of col u m n s eq ual to the bu rst
length is effectively se lected. All accesses for that burs t take place within this block—
meaning that the burst will wrap within the block if a boundary is reached. The block is
uniquely selected by A[i:1] when BL = 2, by A[i:2] when BL = 4, and by A[i:3] when BL = 8
(where Ai is the most significant colum n address bit for a given configuration). The
remaining (least significant) address bit(s) is (are) used to select the starting location
within the block. For example: for BL = 8, A[i:3]select the eight-data-element block;
A[2:0] select the first access within the block.
Burst Type
Accesse s within a given b urst may be progr ammed to be eithe r sequential or interleaved;
this is referred to as the burst type and is selected via bit M3.
The ordering of accesses within a burst is determined b y the burst lengt h, the burst t ype ,
and the starting column address, as shown in Table 26.
Table 26: Burst Definition
Burst Length Starting Column Address
Order of Accesses Within a Burst
Type = Sequential Type = Interleaved
2–A0 ––
––0 0-1 0-1
––1 1-0 1-0
4–A1 A0 ––
0 0 0-1-2-3 0-1-2-3
0 1 1-2-3-0 1-0-3-2
1 0 2-3-0-1 2-3-0-1
1 1 3-0-1-2 3-2-1-0
8A2 A1 A0 ––
0 0 0 0-1-2-3-4-5-6-7 0-1-2-3-4-5-6-7
0 0 1 1-2-3-4-5-6-7-0 1-0-3-2-5-4-7-6
0 1 0 2-3-4-5-6-7-0-1 2-3-0-1-6-7-4-5
0 1 1 3-4-5-6-7-0-1-2 3-2-1-0-7-6-5-4
1 0 0 4-5-6-7-0-1-2-3 4-5-6-7-0-1-2-3
1 0 1 5-6-7-0-1-2-3-4 5-4-7-6-1-0-3-2
1 1 0 6-7-0-1-2-3-4-5 6-7-4-5-2-3-0-1
1 1 1 7-0-1-2-3-4-5-6 7-6-5-4-3-2-1-0
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 57 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
CAS Latency (CL)
The CL is the delay, in clock cycles, between the registration of a READ command and
the availability of the first bit of output data. The latency can be set to 2, 2.5, or 3 (-5B
only) clocks, as shown in Figure 15. Reserved states should not be used, as unknow n
operation or incompatibilit y with future versions may result.
If a READ command is registered at clock edge n, and the latency is m clocks, the data
will be available nomina ll y co i nci dent with clock edge n + m. Table 27 on page 58 indi-
cates the operating frequencies at which each CL setting can be used.
Figure 15: CAS Latency
Note: BL = 4 in the cases shown; shown with nominal tAC, tDQSCK, and tDQSQ.
CK
CK#
Command
DQ
DQS
CL = 2
READ NOP NOP NOP
READ NOP NOP NOP
CK
CK#
Command
DQ
DQS
CL = 2.5
T0 T1 T2 T2n T3 T3n
T0 T1 T2 T2n T3 T3n
Dont CareTransitioning Data
READ NOP NOP NOP
CK
CK#
Command
DQ
DQS
CL = 3
T0 T1 T2 T3 T3n
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 58 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Operating Mode
The normal operating mode is selected by issuing an LMR command with bits A7–An
each set to zero and bits A[6:0] set to the desired values. A DLL reset is initiated by
issuing an LMR command with bits A7 and A[n:9] each set to zero, bit A8 set to one, and
bits A[6:0] set to the desired values. Although not required by the Micron device, JEDEC
specifications recommend that an LMR command resetting the DLL should always be
followed by an LMR command selecting normal operating mode.
All other combinations of values for A[ n:7] are r eserved for future use and/or test modes.
Test modes and reserved states should not be used, as unkno wn operation or incompat-
ibility with future versions may result.
Extended Mode Register
The extended mode register controls functions beyond those controlled by the mode
r egister; these additional functions ar e DLL enable/disable and output drive strength.
These functions ar e controlled via the bits shown in Figure 16 on page 59. The extended
mode reg ister is progra mmed via the LMR command to the mode register (with BA0 = 1
and BA1 = 0) and will retain the stored information until it is programmed again or until
the device loses power. The enabling of the DLL should always be followed by an LMR
command to the mode register (BA0/BA1 = 0) to reset the DLL. The extended mode
register must be loaded when all banks are idle and no bursts are in progress, and the
controller must wait the specified time before initiating any subsequent operation.
Violating ei the r requirement could result in an unspecified operatio n.
Output Drive Strength
The normal drive strength for all outputs is specified to be SSTL_2, Class II. The Design
Revision F and K devices support a programmable option for reduced drive. This option
is intended for the support of the lighte r load and/or point-to-point envi ronm ent s. The
selection of the reduced drive strength will alter the DQ and DQS pins from SSTL_2,
Class II drive strength to a reduced drive strength, whic h is approximately 54% of the
SSTL_2, Class II drive strength.
DLL Enable/Disable
When the part is running without the DLL enabled, device functionality may be altered.
The DLL must be enabled for normal operation. DLL enable is required during power-
up initialization and upon returning to normal operation after having disabled the DLL
for the purpose of debug or evaluati on (when the devi ce exits sel f refresh mode, the DLL
is enabled automatically). Anytime the DLL is enabled, 200 clock cycles with CKE HIGH
must occur befor e a READ command can be issued.
Table 27: CAS Latency
Speed
Allowable Operating Clock Frequency (MHz)
CL = 2 CL = 2.5 CL = 3
-5B 75 f 133 75 f 167 133 f 200
-6/-6T 75 f 133 75 f 167
-75E 75 f 133 75 f 133
-75Z 75 f 133 75 f 133
-75 75 f 100 75 f 133
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 59 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 16: Extended Mode Register Definition
Notes: 1. n is the most significant row address bit from Table 2 on page 2.
2. The QFC# option is not supported.
ACTIVE
After a row is opened with an ACTIVE command, a READ or WRITE command may be
issued to that row, subject to the tRCD specification. tRCD (MIN) should be divided by
the clock period and rounded up to the next whole number to determine the earliest
clock edge after the ACTIVE command on which a READ or WRITE command can be
entered. For example, a tRCD specification of 20ns with a 133 MHz clock (7.5ns period)
results in 2.7 clocks rounded to 3. This is reflected in Figu re 1 7 on page 60, which covers
any case wher e 2 < tR CD (MIN)/tCK 3 (Figur e 17 also sho ws the same case for tRRD; the
same procedure is used to convert other specification limits from time units to clock
cycles).
A row remains active (or open) for accesses until a PRECHARGE command is issued to
that bank. A PRECHARGE command must be issued before opening a different row in
the same bank.
A subsequent ACTIVE command to a differ ent row in the same bank can only be issued
after the previous active row has been closed” (precharged). The minimum time
interval between successive ACTIVE commands to the same bank is defined by tRC.
A subsequent ACTIVE command to another bank can be issued while the first bank is
being accessed, which resul ts in a r eduction of total r o w-access o verhead. The minimum
time interval between successive ACTIVE commands to different banks is defined by
tRRD.
Operating Mode
Reserved
Reserved
E3
0
E4
0
E1, E0
Valid
DLL
Enable
Disable
A9 A7 A6 A5 A4 A3A8 A2 A1 A0
Extended mode
register (Ex)
Address bus
976543821
0
1
E0
0
1
Drive Strength
Normal
Reduced
E1
Operating Mode
. . .AnBA1 BA0
. . .n1
n + 1n + 2
E6
0
E7
0
E8
0
E9
0
E5
0
. . .
0
En
0
DS
E22
0
Mn + 1
0
1
0
1
Mode Register Definition
Base mode register
Extended mode register
Reserved
Reserved
Mn + 2
0
0
1
1
DLL
0
10
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 60 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 17: Example: Meeting tRCD (tRRD) MIN When 2 < tRCD (tRRD) MIN/tCK 3
READ
During the READ command, the value on input A10 determines whether or not auto
precharge is used. If auto precharge is selected, the row being accessed will be
precharged at the end of the READ burst; if auto precharge is not selected, the row will
remain open for subsequent accesses.
Note: For the READ com m a nd s use d in the following illustrations, auto precharge is dis-
abled.
During READ bursts, the valid data-out element from the starting column address will
be available following the CL after the READ command. Each subsequent data-out
element will be v a lid nominally at the next positive or negative clock edge (that is, at the
next crossing of CK and CK#). Figure 18 on page 62 shows the general timing for each
possible CL setting. DQS is driven by the DDR SDRAM along with output data. The
initial LOW state on DQS is know n as the read preamble; the LOW state coincident with
the last data-out element is known as the read postamble.
Upon completion of a burst, assuming no other commands have been initiated, the DQ
will go High-Z. Detailed explanations of tDQSQ (valid data-out skew), tQH (data-out
window hold), and the valid data window are depicted in Figure 26 on page 70 and
Figure 27 on page 71. Detailed explanations of tDQSCK (DQS transition skew to CK) and
tAC (data-out transition skew to CK) are depicted in Figure 28 on page 72.
Data from any READ burst may be concatenated or truncated with data from a subse-
quent READ command. In either case , a continuous flo w of data can be maintained. The
first data element from the new burst follows either the last element of a completed
burst or the last desired data element of a longer burst which is being truncated. The
new READ command should be issued x cycl es afte r the firs t RE AD com mand, where x
equals the number of desired data element pairs (pairs are required by the 2n-prefetch
architecture). This is shown in Figure 19 on page 63. A READ command can be initiated
on any clock cycle following a previous READ command. Nonconsecutive read data is
illustrated in Figure 20 on page 64. Full-speed random read accesses within a page (or
pages) can be performed, as shown in Figure 21 on page 65.
Command
BA0, BA1
ACTACT
NOP
tRRD tRCD
CK
CK#
Bank xBank y
Address Row Row
NOP
RD/WR
NOP
Bank y
Col
NOP
T0 T1 T2 T3 T4 T5 T6T7
Dont Care
NOP
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 61 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Data from any READ burst may be truncated with a BURST TERMINATE command, as
shown in Figure 22 on page 66. The BURST TERMINATE latency is equal to the CL, that
is, the BURST TERMINATE command should be issued x cycles after the READ
command where x equals the number of desired data element pairs (pairs are required
by the 2n-p refetch archit ec tu re) .
Data from any READ burst must be completed or truncated before a subsequent WRITE
command can be issued. If truncation is necessary, the BURST TERMINATE command
must be used, as shown in Figure 23 on page 67. The tDQSS (NOM) case is shown; the
tDQSS (MAX) case has a longer bus idle time. (tDQSS [MIN] and tDQSS [MAX] are
defined in the section on WRITEs.) A READ burst may be follo wed by, or truncated with,
a PRECHARGE command to the same bank provided that auto precharge was not acti-
vated.
The PRECHARGE command should be issued x cycles after the READ command, where
x equals the number of desir ed data element pairs (pairs are requir ed by the 2n-prefetch
architectur e). This is shown in Figur e24 on page 68. Following the PRECHARGE
command, a subsequent command to the same bank cannot be issued until both tRAS
and tRP hav e been met. Part of the row pr echarg e time is hidden during the access of the
last data elements.
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 62 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 18: READ Burst
Notes: 1. DO n = data-out from column n.
2. BL = 4.
3. Three subsequent elements of data-out appear in the programmed order following DO n.
4. Shown with nominal tAC, tDQSCK, and tDQSQ.
READ NOP NOP NOP NOP NOP
READ NOP NOP NOP NOP NOP
CL = 2
CL = 2.5
DO
n
DO
n
T0 T1 T2 T3T2n T3n T4 T5
T0 T1 T2 T3T2n T3n T4 T5
READ NOP NOP NOP NOP NOP
CL = 3
DO
n
T0 T1 T2 T3 T4nT3n T4 T5
Bank a,
Col n
Bank a,
Col n
Bank a,
Col n
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Transitioning Data Don’t Care
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 63 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 19: Consecutive READ Bursts
Notes: 1. DO n (or b) = data-out from column n (or column b).
2. BL = 4 or BL = 8 (if BL = 4, the bursts are concatenated; if BL = 8, the second burst interrupts
the first).
3. Three subsequent elements of data-out appear in the programmed order following DO n.
4. Three (or seven) subsequent elements of data-out appear in the programmed order follow-
ing DO b.
5. Shown with nominal tAC, tDQSCK, and tDQSQ.
6. Example applies only when READ commands are issued to same device.
READ NOP READ NOP NOP NOP
READ NOP READ NOP NOP NOP
CL = 2
CL = 2.5
DO
nDO
b
DO
nDO
b
T0 T1 T2 T3T2n T3n T4 T5T4n T5n
T0 T1 T2 T3T2n T3n T4 T5T4n T5n
READ NOP READ NOP NOP NOP
CL = 3
DO
nDO
b
T0 T1 T2 T3 T3n T4 T5T4n T5n
Bank,
Col nBank,
Col b
Bank,
Col nBank,
Col b
Bank,
Col nBank,
Col b
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Transitioning Data Don’t Care
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 64 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 20: Nonconsecutive READ Bursts
Notes: 1. DO n (or b) = data-out from column n (or column b).
2. BL = 4 or BL = 8 (if BL = 4, the bursts are concatenated; if BL = 8, the second burst interrupts
the first).
3. Three subsequent elements of data-out appear in the programmed order following DO n.
4. Three (or seven) subsequent elements of data-out appear in the programmed order follow-
ing DO b.
5. Shown with nominal tAC, tDQSCK, and tDQSQ.
READ NOP NOP NOP NOP NOPREAD
CL = 2
CL = 2.5
DO
n
T0 T1 T2 T3T2n T3n T4 T5 T5n T6
READ NOP NOP NOP NOP NOPREAD
T0 T1 T2 T3T2n T3n T4 T5 T5n T6
DO
b
DO
nDO
b
CL = 3
READ NOP NOP NOP NOP NOPREAD
T0 T1 T2 T3 T3n T4 T5 T6
DO
nDO
b
T4n
Bank,
Col nBank,
Col b
Bank,
Col nBank,
Col b
Bank,
Col nBank,
Col b
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Transitioning Data Dont Care
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 65 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 21: Random READ Accesses
Notes: 1. DO n (or x or b or g) = data-out from column n (or column x or column b or column g).
2. BL = 2, BL = 4, or BL = 8 (if BL = 4 or BL = 8, the following burst interrupts the previous).
3. n', x', b', or g' indicate the next data-out following DO n, DO x, DO b, or DO g, respectively.
4. READs are to an active row in any bank.
5. Shown with nominal tAC, tDQSCK, and tDQSQ.
READ READ READ NOP NOPREAD
CL = 2
CL = 2.5
DO
nDO
x' DO
g
DO
n' DO
b
DO
xDO
b'
DO
nDO
x'
DO
n' DO
b
DO
xDO
b'
T0 T1 T2 T3T2n T3n T4 T5T4n T5n
READ READ READ NOP NOPREAD
T0 T1 T2 T3T2n T3n T4 T5T4n T5n
CL = 3
DO
nDO
x'
DO
n' DO
b
DO
xDO
b'
READ READ READ NOP NOPREAD
T0 T1 T2 T3 T3n T4 T5T4n T5n
Bank,
Col nBank,
Col b
Bank,
Col xBank,
Col g
Bank,
Col nBank,
Col b
Bank,
Col xBank,
Col g
Bank,
Col nBank,
Col b
Bank,
Col xBank,
Col g
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Transitioning Data Dont Care
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 66 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 22: Terminating a READ Burst
Notes: 1. Page remains open.
2. DO n = data-out from column n.
3. BL = 4.
4. Subsequent element of data-out appears in the programmed order following DO n.
5. Shown with nominal tAC, tDQSCK, and tDQSQ.
READ NOP NOP NOP NOP
Bank a,
Col n
READ NOP NOP NOP NOP
Bank a,
Col n
CL = 2
CL = 2.5
DO
n
DO
n
T0 T1 T2 T3T2n T4 T5
T0 T1 T2 T3T2n T4 T5
READ NOP NOP NOP NOP
Bank a,
Col n
CL = 3
DO
n
T0 T1 T2 T3 T3n T4 T5
BST1
BST1
BST1
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Transitioning Data Don’t Care
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 67 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 23: READ-to-WRITE
Notes: 1. Page remains open.
2. DO n = data-out from column n; DI b = data-in from column b.
3. BL = 4 (applies for burst s of 8 as well; if BL = 2, the BURST command shown can be NOP).
4. One subsequent element of data-out appears in the programmed order following DO n.
5. Data-in elements are applied following DI b in the programmed order.
6. Shown with nominal tAC, tDQSCK, and tDQSQ.
READ BST1NOP NOP NOP
Bank,
Col n
WRITE
Bank,
Col b
T0 T1 T2 T3T2n T4 T5T4n T5n
t
(NOM)
DQSS
DI
b
READ BST1NOP WRITE NOP
Bank a,
Col n
NOP
T0 T1 T2 T3 T3n T4 T5 T5n
DO
n
DO
n
t
(NOM)
DQSS
READ NOP NOP
Bank,
Col n
WRITE
Bank,
Col b
T0 T1 T2 T3T2n T4 T5 T5n
t
(NOM)
DQSS
DI
b
DO
n
NOP
CL = 2.5
CL = 2
T3n
CL = 3
DI
b
BST1
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Transitioning Data Dont Care
DM
DM
DM
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 68 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 24: READ-to-PRECHARGE
Notes: 1. Provided tRAS (MIN) is met, a READ command with auto precharge enabled would cause a
precharge to be performed at x number of clock cycles after the READ command, where
x=BL/2.
2. DO n = data-out from column n.
3. BL = 4 or an interrupted burst of 8.
4. Three subsequent elements of data-out appear in the programmed order following DO n.
5. Shown with nominal tAC, tDQSCK, and tDQSQ.
6. READ-to-PRECHARGE equals two clocks, which allows two data pairs of data-out; it is also
assumed that tRAS (MIN) is met.
7. An ACTIVE command to the same bank is only allowed if tRC (MIN) is met.
READ NOP PRE NOP NOP ACT
Bank a,
Col nBank a,
(a or all)Bank a,
Row
READ NOP PRE NOP NOP ACT
Bank a,
Col n
CL = 2 tRP
tRP
CL = 2.5
DO
n
DO
n
T0 T1 T2 T3T2n T3n T4 T5
T0 T1 T2 T3T2n T3n T4 T5
Bank a,
(a or all)Bank a,
Row
READ NOP PRE NOP NOP ACT
Bank a,
Col n
tRP
CL = 3
DO
n
T0 T1 T2 T3 T4nT3n T4 T5
Bank a,
(a or all)Bank a,
Row
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Command
Address
DQS
DQ
CK#
CK
Transitioning Data Dont Care
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 69 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 25: Bank READ – Without Auto Precharge
Notes: 1. NOP commands are shown for ease of illustration; other commands may be valid at these
times.
2. BL = 4.
3. The PRECHARGE command ca n onl y be applied at T5 if tRAS (MIN) is met.
4. Disable auto precharge.
5. “Don’t Care” if A10 is HIGH at T5.
6. DO n (or b) = data-out from column n (or column b); subseque nt elements ar e pr o v ide d in
the programmed order.
7. Refer to Figure 26 on page 70, Figure 27 on page 71, and Figure 28 on page 72 for detailed
DQS and DQ timing.
CK
CK#
CKE
A10
BA0, BA1
tCK tCH tCL
tIS
tIS
tIH
tIS
tIS
tIH
tIH
tIH
tIS tIH
tRCD
tRC
tRP
CL = 2
DM
T0 T1 T2 T3 T4 T5 T5n T6nT6 T7 T8
DQS
Case 1: tAC
(
MIN)
and tDQSCK
(
MIN)
Case 2: tAC
(
MAX)
and tDQSCK
(
MAX)
DQS
t
RPRE
tRPRE
tRPST
tRPST
t
DQSCK
(
MIN)
t
LZ
(
MIN)
t
AC
(
MIN)
t
LZ
(
MIN)
DO
n
t
HZ
(
MAX)
t
AC
(
MAX)
DO
n
ACT
Col n
Bank xBank x
ACT
Bank x
t
DQSCK (MAX)
NOP1NOP1NOP1NOP1NOP1
READ2PRE3
4
Bank x5
tRAS3
Row
Row
Row
Row
DQ
DQ
Command
Address
Transitioning Data Don’t Care
All banks
One bank
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 70 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 26: x4, x8 Data Output Timing – tDQSQ, tQH, and Data Valid Window
Notes: 1. tHP is the lesser of tCL or tCH clock transition collectively when a bank is active.
2. tDQSQ is derive d at each DQS clock edge, is not cumulative over time, begins with DQS
transition, and ends w ith the last valid DQ transition.
3. DQ transitioning after DQS transition define the tDQSQ window. DQS transitions at T2 and
T2n are an “early DQS”; at T3, a “nominal DQS”; and at T3n, a “late DQS”.
4. For a x4, only two DQ apply.
5. tQH is derived from tHP: tQH = tHP - tQHS.
6. The data valid window is derived for each DQS transitions and is defined as tQH - tDQSQ.
DQ (last data valid)
DQ4
DQ4
DQ4
DQ4
DQ4
DQ4
DQS3
DQ (last data valid)
DQ (first data no longer valid)
DQ (first data no longer valid)
All DQ and DQS collectively6
Earliest signal transition
Latest signal transition
T2
T2
T2
T2n
T2n
T2n
T3
T3
T3
T3n
T3n
T3n
CK
CK#
T1 T2 T3 T4T2n T3n
tQH5
tHP
1
tHP
1
tHP
1
tQH5tQH5
tHP
1
tHP
1
tHP
1
tQH5
tDQSQ
2
tDQSQ
2
tDQSQ
2
tDQSQ
2
Data
valid
window
Data
valid
window
Data
valid
window
Data
valid
window
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 71 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 27: x16 Data Output Timing – tDQSQ, tQH, and Data Valid Window
Notes: 1. tHP is the lesser of tCL or tCH clock transition collectively when a bank is active.
2. tDQSQ is derive d at each DQS clock edge, is not cumulative over time, begins with DQS
transition, and ends w ith the last valid DQ transition.
3. DQ transitioning after DQS transition define the tDQSQ window . LDQS defines the lower
byte, and UDQS defines the upper byte.
4. DQ0, DQ1, DQ2, DQ3, DQ4, DQ5, DQ6, or DQ7.
5. tQH is derived from tHP: tQH = tHP - tQHS.
6. The data valid window is derived for each DQS transition and is tQH - tDQSQ.
7. DQ8, DQ9, DQ10, D11, DQ12, DQ13, DQ14, or DQ15.
DQ (last data valid)4
DQ4
DQ4
DQ4
DQ4
DQ4
DQ4
LDQS3
DQ (last data valid)4
DQ (first data no longer valid)4
DQ (first data no longer valid)4
DQ0–DQ7 and LDQS collectively6
T2
T2
T2
T2n
T2n
T2n
T3
T3
T3
T3n
T3n
T3n
CK
CK#
T1 T2 T3 T4T2n T3n
tQH5tQH5
tDQSQ
2
tDQSQ
2
tDQSQ
2
tDQSQ
2
Data valid
window Data valid
window
DQ (last data valid)7
DQ7
DQ7
DQ7
DQ7
DQ7
DQ7
UDQS3
DQ (last data valid)7
DQ (first data no longer valid)7
DQ (first data no longer valid)7
DQ8–DQ15 and UDQS collectively6
T2
T2
T2
T2n
T2n
T2n
T3
T3
T3
T3n
T3n
T3n
tQH5tQH5tQH5tQH5
tDQSQ2tDQSQ2tDQSQ2
tDQSQ2
tHP
1
tHP
1
tHP
1
tHP
1
tHP
1
tHP
1
tQH5
tQH5
Data valid
window
Data valid
window Data valid
window Data valid
window Data valid
window
Upper byte
Lower byte
Data valid
window
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 72 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 28: Data Output Timing – tAC and tDQSCK
Notes: 1. READ command with CL = 2 issued at T0.
2. tDQSCK is the DQS output window relative to CK and is the “long term” component of the
DQS skew.
3. DQ transitioning after DQS transition define the tDQSQ window .
4. All DQ must transition by tDQSQ after DQS transitions, regardless of tAC.
5. tAC is the DQ output window relative to CK and is the “long term” component of DQ skew.
6. tLZ (MIN) and tAC (MIN) are the first valid signal transitions.
7. tHZ (MAX) and tAC (MAX) are the latest valid signal transitions.
WRITE
During a WRITE command, the value on input A10 determines whether or not auto
precharge is used. If auto precharge is selected, the row being accessed will be
precharged at the end of the WRITE burst (after tWR time); if auto precharge is not
selected, the row will remain open for subsequent accesses.
Input data appearing on the DQ is written to the memory array subject to the DM input
logic level appearing coincident with the data. If a given DM signal i s re gister ed L O W, the
corresponding data will be written to memory. If the DM signal is registered HIGH, the
corresponding data inputs will be ignored, and a WRITE will not be executed to that
byte/column location.
Note: For the WRITE commands used in the following illustrations, auto precharge is dis-
abled.
During WRITE bursts, the first valid data-in element will be registered on the first rising
edge of DQS following the WRITE command, and subsequent data elements will be
registered on successive edges of DQS. The LOW state on DQS between the WRITE
command and the first rising edge is known as the write preamble; the LOW state on
DQS following the last data-in element is known as the write postamble.
The time betwe en the WRIT E command and the first corr esponding rising edge of DQS
(tDQSS) is specified with a relatively wide range (from 75% to 125% of one clock cycle).
All of the WRITE diagrams show the nominal case, and where the two extreme cases
(that is, tDQSS [MIN] and tDQSS [MAX]) might not be intuitive; they have also been
included. F igur e29 on page 74 shows the nominal case and the extremes of tDQSS for
BL = 4. Upon completion of a burst, assuming no other commands have been initiated,
the DQ will remain High-Z and any additional input data will be ignored.
CK
CK#
DQS or LDQS/UDQS3
T1 T2 T3 T4 T5
T2n T3n T4n T5n T6
tRPST
tLZ (MIN)
tDQSCK2 (MAX)
tDQSCK2 (MIN) tDQSCK2 (MAX)
tDQSCK2 (MIN)
tHZ (MAX)
All DQ values collectively4
tAC5
(MIN) tAC5
(MAX)
tLZ (MIN) tHZ (MAX)
T2
T2
T2n T3n T4n T5n
T2n
T2n
T3n
T3n
T4n
T4n
T5n
T5n
T3
T4
T4
T5
T5
T2 T3 T4 T5
T3
DQ (last data valid)
DQ (first data valid)
T01
tRPRE
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 73 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Data for any WRITE burst may be concatenated with or truncated with a subsequent
WRITE command. In either case, a continuous flow of input d ata can b e main tai ne d.
The new WRITE command can be issued on any positive edge of clock following the
previous WRITE command. The first data element from the new burst is applied after
either the last element of a completed burst or the last desired data element of a longer
burst which is being truncated. The new WRITE command should be issued x cycles
after the first WRITE command, where x equals the number of desired data element
pairs (pairs are required by the 2n-prefetch architecture).
Figure 30 on page 75 shows concatenated bursts of 4. An example of nonconsecutive
WRITEs is shown in Figure 31 on page 76. Full-speed ra ndom write accesses within a
page or pages can be performed as shown in Figure 32 on page 76.
Data for any WRITE burst may be followed by a subsequent READ command. To follow a
WRITE without truncating the WRITE burst, tWTR should be met, as shown in Figure 33
on page 77.
Data for any WRITE burst may be truncated b y a subsequent READ command, as shown
in Figure 34 on page 78.
Note that only the data-in pairs that are r egistered prior to the tWTR period are written
to the internal array, and any subsequent data-in should be masked with DM, as shown
in Figure 35 on page 79.
Data for any WRITE burst may be followed by a subsequent PRECHARGE command. To
follow a WRITE without truncating the WRITE burst, tWR should be met, as shown in
Figure 36 on page80.
Data for any WRITE burst may be truncated by a subsequent PRECHARGE command, as
shown in Figure 37 on page 81 and Figure 38 on page 82. Only the data-in pairs regis-
tered prior to the tWR per io d are written to the internal array; any subsequent data-in
should be masked with DM, as show n in F igures 37 and 38. After the PRECHARGE
command, a subsequent command to the same bank cannot be issued until tRP is met.
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 74 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 29: WRITE Burst
Notes: 1. DI b = data-in for column b.
2. Three subsequent elements of data-in are applied in the programmed order following DI b.
3. An uninterrupted burst of 4 is shown.
4. A10 is LOW with the WRITE command (auto precharge i s disabled).
DQS
tDQSS (MAX)
tDQSS (NOM)
tDQSS (MIN)
tDQSS
DM
DQ
CK
CK#
Command WRITE NOP NOP
Address Bank a,
Col b
NOP
T0 T1 T2 T3T2n
DQS tDQSS
DM
DQ
DQS
DM
DQ DI
b
DI
b
DI
b
Don’t CareTransitioning Data
tDQSS
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 75 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 30: Consecutive WRITE-to-WRITE
Notes: 1. DI b (or n) = data-in from column b (or column n).
2. Three subsequent elements of data-in are applied in the programmed order following DI b.
3. Three subsequent elements of data-in are applied in the programmed order following DI n.
4. An uninterrupted burst of 4 is shown.
5. Each WRITE command may be to any bank.
Address
tDQSS (NOM)
CK
CK#
Command WRITE NOP WRITE NOP NOP
Bank,
Col b
NOP
Bank,
Col n
T0 T1 T2 T3T2n T4 T5T4nT3nT1n
DQ
DQS
DM
DI
n
DI
b
Don’t CareTransitioning Data
tDQSS
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 76 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 31: Nonconsecutive WRITE-to-WRITE
Notes: 1. DI b (or n) = data-in from column b (or column n).
2. Three subsequent elements of data-in are applied in the programmed order following DI b.
3. Three subsequent elements of data-in are applied in the programmed order following DI n.
4. An uninterrupted burst of 4 is shown.
5. Each WRITE command may be to any bank.
Figure 32: Random WRITE Cycles
Notes: 1. DI b (or x or n or a or g) = data-in from column b (or co lumn x, or column n, or column a, or
column g).
2. b', x', n', a' or g' indicate the next data-in following DO b, DO x, DO n, DO a, or DO g,
respectively.
3. Programmed BL = 2, BL = 4, or BL = 8 in cases shown.
4. Each WRITE command may be to any bank.
CK
Command WRITE NOP NOP NOP NOP
Address Bank,
Col b
WRITE
Bank,
Col n
T0 T1 T2 T3T2n T4 T5T4nT1n T5n
DQ
DQS
DM
DI
n
DI
b
tDQSS (NOM) tDQSS
Don’t CareTransitioning Data
CK#
tDQSS (NOM)
CK
CK#
Command WRITE WRITE WRITE WRITE NOP
Address Bank,
Col bBank,
Col xBank,
Col nBank,
Col g
WRITE
Bank,
Col a
T0 T1 T2 T3T2n T4 T5T4nT1n T3n T5n
DQ
DQS
DM
DI
bDI
b'DI
xDI
x'DI
nDI
n'DI
aDI
a'DI
gDI
g'
Don’t CareTransitioning Data
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 77 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 33: WRITE-to-READ – Uninterrupting
Notes: 1. DI b = data-in for column b; DO n = data-out for column n.
2. Three subsequent elements of data-in are applied in the programmed order following DI b.
3. An uninterrupted burst of 4 is shown.
4. tWTR is referenced from the first positive CK edge after the last data-in pair.
5. The READ and WRITE commands are to the same device. However, the READ and WRITE
commands may be to different devices, in which case tWTR is not required, and the READ
command could be applied earlier.
6. A10 is LOW with the WRITE command (auto precharge i s disabled).
tDQSS (NOM)
CK
CK#
Command WRITE NOP NOP READ NOP NOP
Address Bank a,
Col bBank a,
Col n
NOP
T0 T1 T2 T3T2n T4 T5T1n T6 T6n
tWTR
CL = 2
DQ
DQS
DM
DI
bDO
n
tDQSS
tDQSS (MIN) CL = 2
DQ
DQS
DM
DI
bDO
n
tDQSS
tDQSS (MAX) CL = 2
DQ
DQS
DM
DI
bDO
n
tDQSS
Don’t CareTransitioning Data
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 78 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 34: WRITE-to-READ – Interrupting
Notes: 1. DI b = data-in for column b; DO n = data-out for column n.
2. An interrupted burst of 4 is shown; two data elements are written.
3. One subsequent element of data-in is applied in the programmed order following DI b.
4. tWTR is referenced from the first positive CK edge after the last data-in pair.
5. A10 is LOW with the WRITE command (auto precharge i s disabled).
6. DQS is required at T2 and T2n (nominal case) to register DM.
7. If the burst of 8 is used, DM and DQS are required at T3 and T3n because the READ com-
mand will not mask these two data ele ments.
tDQSS (NOM)
CK
CK#
Command WRITE NOP NOP NOP NOP NOP
Address Bank a,
Col bBank a,
Col n
READ
T0 T1 T2 T3T2n T4 T5 T5nT1n T6 T6n
tWTR
CL = 2
DQ
DQS
DM
DI
bDO
n
tDQSS (MIN) CL = 2
DQ
DQS
DM
DI
b
tDQSS (MAX) CL = 2
DQ
DQS
DM
DI
bDO
n
DO
n
Don’t CareTransitioning Data
tDQSS
tDQSS
tDQSS
T3n
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 79 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 35: WRITE-to-READ – Odd Number of Data, Interrupting
Notes: 1. DI b = data-in for column b; DO n = data-out for column n.
2. An interrupted burst of 4 is shown; one data element is written.
3. tWTR is refere n ced from the fir st positive CK edge after the last desired data-in pair (not
the last two data elements).
4. A10 is LOW with the WRITE command (auto precharge i s disabled).
5. DQS is required at T1n, T2, and T2n (nominal case) to register DM.
6. If the burst of 8 is used, DM and DQS are required at T3–T3n because the READ command
will not mask these data elements.
tDQSS (NOM)
CK
CK#
Command WRITE NOP NOP NOP NOP NOP
Address Bank a,
Col bBank a,
Col n
READ
T0 T1 T2 T3T2n T4 T5T1n T6 T6nT5n
tWTR
CL = 2
DQ
DQS
DM
DI
bDO
n
tDQSS (MIN) CL = 2
DQ
DQS
DM
DI
bDO
n
tDQSS (MAX) CL = 2
DQ
DQS
DM
DI
bDO
n
Don’t CareTransitioning Data
tDQSS
tDQSS
tDQSS
T3n
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 80 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 36: WRITE-to-PRECHARGE – Uninterrupting
Notes: 1. DI b = data-in for column b.
2. Three subsequent elements of data-in are applied in the programmed order following DI b.
3. An uninterrupted burst of 4 is shown.
4. tWR is referenced from the first positive CK edge after the last data-in pair.
5. The PRECHARGE and WRITE commands are to the same device. However, the PRECHARGE
and WRITE commands may be to different devices, in which case tWR is not required, and
the PRECHARGE command could be applied earlier.
6. A10 is LOW with the WRITE command (auto precharge i s disabled).
tDQSS (NOM)
CK
CK#
Command WRITE NOP NOP NOP NOP
Address Bank a,
Col bBank,
(a or all)
NOP
T0 T1 T2 T3T2n T4 T5T1n T6
tWR tRP
DQ
DQS
DM
DI
b
tDQSS (MIN)
DQ
DQS
DM
DI
b
tDQSS (MAX)
DQ
DQS
DM
DI
b
Don’t CareTransitioning Data
tDQSS
tDQSS
tDQSS
PRE
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 81 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 37: WRITE-to-PRECHARGE – Interrupting
Notes: 1. DI b = data-in for column b.
2. Subsequent element of data-in is applied in the programmed order following DI b.
3. An interrupted burst of 8 is shown; two data elements are written.
4. tWR is referenced from the first positive CK edge after the last data-in pair.
5. A10 is LOW with the WRITE command (auto precharge i s disabled).
6. DQS is required at T4 and T4n (nominal case) to register DM.
7. If the burst of 4 is used, DQS and DM are not required at T3, T3n, T4, and T4n.
tDQSS
tDQSS (NOM)
CK
CK#
Command WRITE NOP NOP NOP NOP
Address Bank a,
Col bBank,
(a or all)
NOP
T0 T1 T2 T3T2n T4 T5T1n T6
tWR tRP
DQ
DQS
DM
DI
b
tDQSS
tDQSS (MIN)
DQ
DQS
DM
DI
b
tDQSS
tDQSS (MAX)
DQ
DQS
DM
DI
b
Don’t CareTransitioning Data
T3n T4n
PRE
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 82 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 38: WRITE-to-PRECHARGE – Odd Number of Data, Interrupting
Notes: 1. DI b = data-in for column b.
2. An interrupted burst of 8 is shown; one data element is written.
3. tWR is referenced from the first positive CK edge after the last data-in pair.
4. A10 is LOW with the WRITE command (auto precharge i s disabled).
5. DQS is required at T4 and T4n (nominal case) to register DM.
6. If the burst of 4 is used, DQS and DM are not required at T3, T3n, T4, and T4n.
tDQSS
tDQSS (NOM)
CK
CK#
Command WRITE NOP NOP NOP NOP
Address Bank a,
Col bBank,
(a or all)
NOP
T0 T1 T2 T3T2n T4 T5T1n T6
tWR tRP
DQ
DQS
DM
DI
b
tDQSS
tDQSS (MIN)
DQ
DQS
DM
tDQSS
tDQSS (MAX)
DQ
DQS
DM
DI
b
DI
b
Don’t CareTransitioning Data
T3n T4n
PRE
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 83 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 39: Bank WRITE – Without Auto Precharge
Notes: 1. NOP commands are shown for ease of illustration; other commands may be valid at these
times.
2. BL = 4.
3. Disable auto precharge.
4. “Don’t Care” if A10 is HIGH at T8.
5. DI b = data-in from column b; subsequent elements are provided in the programmed order.
6. See Figure 41 on page 85 for detailed DQ timing.
Command NOP1NOP1NOP1NOP1NOP1NOP1
WRITE2
3
Bank x4
DQ5
Address
Row
Row
CK
CK#
CKE
A10
BA0, BA1
tCK tCH tCL
tIS
tIS
tIH
tIS
tIS
tIH
tIH
tIH
tIS tIH
tRCD
tRAS tRP
tWR
T0 T1 T2 T3 T4 T5 T5n T6 T7 T8T4n
ACT
Col n
One bank
All banks
Bank x
PRE
Bank x
tDQSL tDQSH tWPST
DQS
DM
DI
b
tDS tDH
tDQSS (NOM)
tWPRE
tWPRES
Don’t CareTransitioning Data
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 84 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 40: WRITE – DM Operation
Notes: 1. NOP commands are shown for ease of illustration; other commands may be valid at these
times.
2. BL = 4.
3. Disable auto precharge.
4. “Don’t Care” if A10 is HIGH at T8.
5. DI b = data-in from column b; subsequent elements are provided in the programmed order.
6. See Figure 41 on page 85 for detailed DQ timing.
Command NOP1NOP1NOP1NOP1NOP1NOP1
3
Bank x4
DQ5
WRITE2
Address Row
Row
CK
CK#
CKE
A10
BA0, BA1
tCK tCH tCL
tIS
tIS
tIH
tIS
tIS
tIH
tIH
tIH
tIS tIH
tRCD
tRAS tRP
tWR
T0 T1 T2 T3 T4 T5 T5n T6 T7 T8T4n
ACT
Col n
One bank
All banks
Bank x
PRE
Bank x
tDQSL tDQSH tWPST
DQS
DM
DI
b
tDS tDH
Don’t CareTransitioning Data
tDQSS (NOM)
tWPRES tWPRE
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 85 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 41: Data Input Timing
Notes: 1. WRITE command issued at T0.
2. tDSH (MIN) generally oc curs during tDQSS (MIN).
3. tDSS (MIN) gener a lly occurs during tDQSS (MAX).
4. For x16, LDQS controls the lower byte and UDQS controls the upper byte.
5. DI b = data-in from column b.
PRECHARGE
The bank(s) will be available for a subsequent row access a specified time (tRP) after the
PRECHAR GE command is issued, except in the case of concurrent auto precharge. With
concurrent auto precharge, a READ or WRITE command to a different bank is allowed as
long as it does not interrupt the data transfer in the current bank and does not violate
any other timing parameters. I nput A10 determines whether one or all banks are to be
precharged, and in the case where only one bank is to be precharged, inputs BA0, BA1
select the bank. When all banks are to be precharged, BA0, BA1 are treated as “Dont
Care.” Once a bank has been precharged, it is in the idle state and must be activated
prior to any READ or WRITE commands being issued to that bank. A PRECHARGE
command will be treated as a NOP if there is no open row in that bank (idle state), or if
the previously open row is already in the process of precharging.
Auto Precharge
Auto precharge is a feature which performs the same individual-bank pr echarge func-
tion described above, but without requiring an explicit command. This is acc o m pli s h ed
by using A10 to enable auto precharge in conjunction with a specific READ or WRITE
command. A precharge of the bank/ row that is addressed with the READ or WRITE
command is automatically performed upon completion of the READ or WRITE burst.
Auto precharge is either enabled or disabled for each individual READ or WRITE
command. This device supports concurrent auto precharge if the command to the other
bank does not interrupt the data transfer to the current bank.
Auto precharge ensures that the precharge is initiated at the earliest valid stage within a
burst. This “earliest valid stage” is determined as if an explicit PRECHARGE command
was issued at the earliest possible time, without violating tRAS (MIN), as described for
each burst type in “Operations” on page 52. The user must not issue another command
to the same bank until the precharge time (tRP) is completed.
T01
tDSH2tDSH2
tDSS3tDSS3
DI
b
DQS
tDQSS
tDQSH tWPST
tDH
tDS
tDQSL
DM
DQ
CK
CK# T1 T1n T2 T2n T3
Don’t CareTransitioning Data
tWPRE
tWPRES
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 86 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 42: Bank READ – with Auto Precharge
Notes: 1. NOP commands are shown for ease of illustration; other commands may be valid at these
times.
2. BL = 4.
3. The READ command can only be applied at T3 if tRAP is satisfied at T3.
4. Enable auto precharge.
5. tRP starts only after tRAS has been satisfied.
6. DO n = data-out from column n; subsequent elements are provided in the programmed
order.
7. Refer to Figure 26 on page 70, Figure 27 on page 71, and Figure 28 on page 72 for detailed
DQS and DQ timing.
NOP1NOP1NOP1NOP1NOP1NOP1
READ2,3
4
tRCD, tRAP3
DQ6
DQ6
Command
tRP5
Address
tLZ (MIN)
Row
Row
Row
Row
CK
CK#
CKE
A10
BA0, BA1
tCKtCHtCL
tIS
tIS
tIH
tIS
tIS
tIH
tIH
tIH
ISIH
tRC
CL = 2
DM
T0 T1 T2 T3 T4 T5 T5n T6nT6T7 T8
DQS
Case 1: tAC (MIN) and tDQSCK (MIN)
Case 2: tAC (MAX) and tDQSCK (MAX)
DQS
tRPRE
tRPRE tRPST
tDQSCK (MIN)
tDQSCK (MAX)
tAC (MIN)
tLZ (MIN)
DO
n
tHZ (MAX)
tAC (MAX)
DO
n
ACT
Col n
Bank xBank x
ACT
Bank x
tRAS
Dont CareTransitioning Data
tRPST
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 87 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Figure 43: Bank WRITE – with Auto Precharge
Notes: 1. NOP commands are shown for ease of illustration; other commands may be valid at these
times.
2. BL = 4.
3. Enable auto precharge.
4. DI n = data-out from column n; subsequent elements are provided in the programmed
order.
5. See Figure 41 on page 85 for detailed DQ timing.
AUTO REFRESH
During au to refresh, the addressing is generated by the internal refresh controller. This
makes the address bits a “Dont Care” during an AUTO REFRESH command. The DDR
SDRAM requires AU TO REFRESH cycles at an average interval of tREFI (MAX).
To allow for improved efficiency in scheduling and switching between tasks, some flexi-
bility in the absolute r efresh interval is provided. A maximum of eight AUTO REFRESH
commands can be posted to any giv en DDR SDRAM, meaning that the maximum abso-
lute interval betw een any AUTO REFRESH command and the next AUTO REFRESH
command is 9 × tREFI(= tREFC). JEDEC specifications only support 8 × tREFI; Micron
specifications exceed the JEDEC requirement by one clock. This maximum ab solute
interval is to allow future support for DLL updates, internal to the DDR SDRAM, to be
restricted to AUTO REFRESH cycles, without allowing excessi ve drift in tAC betwee n
updates.
Command NOP1NOP1NOP1NOP1NOP1NOP1NOP1
WRITE2
3
DQ4
Address Row
Row
CK
CK#
CKE
A10
BA0, BA1
tCK tCH tCL
tIS
tIS
tIH
tIS
tIS
tIH
tIH
tIH
tIS tIH
tRCD
tRAS tRP
tWR
T0 T1 T2 T3 T4 T5 T5n T6 T7 T8T4n
ACT
Col n
Bank xBank x
tDQSL tDQSH tWPST
DQS
DM
DI
b
tDS tDH
tDQSS (NOM)
Don’t CareTransitioning Data
tWPRES tWPRE
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 88 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Although not a JEDEC r eq uirement, to provide for future functionality feat ures, CKE
must be active (HIGH) during the AUTO REFRESH period. The AUTO REFRESH period
begins when the AUTO REFRESH command is registered and ends tRFC later.
Figure 44: Auto Refresh Mode
Notes: 1. NOP commands are shown for ease of illustration; other valid commands may be possible at
these times. CKE must be active during clock-positive transitions.
2. NOP or COMMAND INHIBIT are the only commands allowed until after tRFC time; CKE must
be active during clock-positive transitions.
3. The second AUTO REFRESH is not required and is only shown as an exampl e of two b ack-to -
back AUTO REFRESH commands.
4. “Don’t Care” if A10 is HIGH at this point; A10 must be HIGH if more than one bank is active
(that is, must precharge all active banks).
5. DM, DQ, and DQS signals are all “Don’t Care”/High-Z for the operations shown.
SELF REFRESH
When in the self refresh mode, the DDR SDRAM retains data without external clocking.
The DLL is automatically disabled upon entering SELF REFRESH and is automatically
enabled upon exiting SELF REFRESH (a DLL reset and 200 clock cycles must then occur
before a READ command can be issued). Input signals except CKE are “Dont Care
during SELF REFRESH. VREF voltage is also r equired for the full duration of SELF
REFRESH.
The procedure for exiting SELF REFRESH requires a sequence of commands. First, CK
and CK# must be stable prior to CKE going back HIGH. Once CKE is HIGH, the DDR
SDRAM must have NOP comm ands issued for tXSNR because time is required for the
completion of any internal refresh in progress. A simple algorithm for meeting both
refresh and DLL requirements is to apply NOPs for tXSRD time, then a DLL RESET (via
CK
CK#
CommandNOP1
ValidValid
NOP1NOP1
PRE
CKE
RA
Address
A10
BA0, BA1
Bank(s)4
BA
AR NOP1,2 AR3NOP1,2 ACTNOP1
One bank
All banks
CK
t
CH
t
CL
t
IS
t
IS
t
IH
t
IH
t
IS
t
IH
RA
DQ5
DM5
DQS5
tRFC
tRP tRFC
T0 T1 T2 T3 T4 Ta0 Tb0
Ta1 Tb1Tb2
Dont Care
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 89 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
the extended mode register) and NOPs for 200 additional clock cycles before applying a
READ. Any command other than a READ can be performed tXSNR (MIN) after the DLL
reset. NOP or DESELECT commands must be issued during the tXSNR (MIN) time.
Figure 45: Self Refresh Mode
Notes: 1. Clock must be stable until after the SELF REFRESH command has been registered. A change
in clock frequency is allowed before Ta0, provided it is within the specified tCK limits.
Regardless, the clock must be stable before exiting self refresh mode—that is, the clock
must be cycling within specifications by Ta0.
2. NOPs are interchangeable with DESELECT commands.
3. AUTO REFRESH is not required at this point but is highly recommended.
4. Device must be in the all banks idle state prior to entering self refresh mode.
5. tXSNR is required before any non-READ command can be applied; that is only NOP or DESE-
LECT commands are allowed until Tb1.
6. tXSRD (200 cycles of a valid clock with CKE = HIGH) is required before any READ command
can be applied.
7. As a general rule, any time self refresh mode is exited, the DRAM may not re-enter the self
refresh mode until all rows have been refreshed via the AUTO REFRESH command at the
distributed refresh rate, tREFI, or faster. However, the self refresh mode may be re-entered
anytime after exiting if each of the following conditions is met:
7a. The DRAM had been in the self refresh mode for a minimum of 200ms prior to exiting.
7b. tXSNR and tXSRD are not violated.
7c. At least two AUTO REFRESH commands are performed during each tREFI interval while
the DRAM remains out of self refresh mode.
8. If the clock frequency is changed during self refresh mode, a DLL reset is required upon exit .
9. Once the device is initialized, VREF must always be powered within specified range.
CK1
CK#
Command2NOP AR
Address
CKE
DQ
DM
DQS
NOP
tRP4
tCHtCLtCK
tIS
tIS
tIH
tIStIH tIS
Enter self refresh mode7Exit self refresh mode7
T0 T11Ta1
Dont Care
Ta01
tXSRD6
()()
()()
()()
()()
NOP Valid3Valid
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
tXSNR5
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
()()
Ta2 Tb1Tb2Tc1
ValidValid
Valid
tIStIH ()()
()()
Valid
()()
()()
()()
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 90 ©2003 Micron Technology, Inc. All rights reserved.
256Mb: x4, x8, x16 DDR SDRAM
Operations
Power-down (CKE Not Active)
Unlike SDR SDRAMs, DDR SDRAMs requi re CKE to be active at all times an access is in
progress, from the issuing of a READ or WRITE command, until completion of the
access. Thus a clock suspend is not supported. For READs, an access complet ion is
defined when the read postamble is satisfied; for WRITEs, when the write recovery time
(tWR) is satisfied.
Po wer-down, as shown in Figure 46 on page 91, is entered when CKE is registered LOW
and all criteria in Table 25 on page 47 are met. If power-down occurs when all banks are
idle, this mode is referred to as precharge power -down; if power-down occurs when a
ro w is active in any bank, this mode is referred to as active power-down. Entering power-
down deactivates the input and output buffers, excluding CK, CK#, and CKE. Fo r
maximum po wer savings, the DLL is frozen during pr echarge po wer -do wn mode. Exiting
power-down requires the device to be at the same voltage and frequency as when it
entered power-dow n . However, power-down duration is limited by the refresh require-
ments of the device (tREFC).
While in power-down, CKE LOW and a stable clock signal must be maintained at the
inputs of the DDR SDRAM, while all other input signals are “ Dont Care.” The pow er-
down state is synchronously exited when CKE is registered HIGH (in conjunction with a
NOP or DESELECT command). A valid executable command may be applied one clock
cycle later.
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900
www.micron.com/productsupport Customer Comment Line: 800-932-4992
Micron, the M logo, and the Micron logo are trademarks of Micron Technology, Inc.All other trademarks are the property of their respec-
tive owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth
herein. Although considered final, these specifications are subject to change, as further product development and data characterization
sometimes occur.
256Mb: x4, x8, x16 DDR SDRAM
Operations
PDF: 09005aef80768abb/Source: 09005aef82a95a3a Micron Technology, Inc., reserves the right to change products or specifica tions without notice.
DDR_x4x8x16_Core2.fm - 256Mb DDR: Rev. S, Core DDR: Rev. E 9/12 EN 91 ©2003 Micron Technology, Inc. All rights reserved.
Figure 46: Power-Down Mode
Notes: 1. Once initialized, VREF must always be powere d within the specified range.
2. If this command is a PRECHARGE (or if the device is already in the idle state), then the
power-down mode shown is precharge power-down. If this command is an ACTIVE (or if at
least one row is already active), then the power-down mode shown is active power-down.
3. No column accesses are allowed to be in progress at the time power-down is entered.
CK
CK#
CommandValid2NOP
Address
CKE
DQ
DM
DQS
Valid
tCK tCHtCL
tIS
tIS
tIH
tIS
tIS tIH
tIH tIS
Enter 3
power-down
mode
Exit
power-down
mode
tREFC
(
) (
)
(
) (
)
(
) (
)
(
) (
)
(
) (
)
(
) (
)
(
) (
)
(
) (
)
(
) (
)
(
) (
)
(
) (
)
T0 T1 Ta0 Ta1 Ta2 T2
NOP
Dont Care
(
) (
)
(
) (
)
ValidValid
1