E M C C o m p o n e n t s October 2013 3-terminal Filters, SMD Array For signal line (UHF band terrestrial digital broadcast / DVB-H band compatible) MEA-PE series MEA1210PE MEA1608PE MEA2010PE 1210[0504 inch]* 1608[0603 inch] 2010[0804 inch] * Dimensions Code JIS[EIA] (2/11) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20131004 / e9621_mea_signal_03.fm (3/11) E M C C o m p o n e n t s 3-terminal Filters, SMD Array Product compatible with RoHS directive Halogen-free Compatible with lead-free solders For signal line (UHF band terrestrial digital broadcast / DVB-H band compatible) Overview of the MEA-PE Series FEATURES Single chip for 2-line or 4-line filters, and compatible with high-density mounting. Compact with a low profile design. Effective as a desensitization countermeasure in information transmission terminals such as smart phones. Can be used for signal lines of mobile device displays. APPLICATION Noise removal from signal lines of smart phones, digital cameras, PCs, game machines, flat TVs, etc. PART NUMBER CONSTRUCTION MEA Series name 1210 LxWxT Dimensions (mm) 1210 1.2x1.0x0.5 1608 1.6x0.8x0.5 2010 2.0x1.0x0.7 PE 220 Product internal code PE Capacitance (pF) 220 22 360 36 T Packaging style Internal code T Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage Type temperature temperature C C MEA1210PE -40 to +85 -40 to +85 MEA1608PE -40 to +85 -40 to +85 MEA2010PE -40 to +85 -40 to +85 The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight pieces/reel 4,000 4,000 4,000 mg 3 3.5 7 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_signal_03.fm (4/11) E M C C o m p o n e n t s Overview of the MEA-PE Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s max. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_signal_03.fm (5/11) E M C C o m p o n e n t s MEA-PE series MEA1210PE Type SHAPE & DIMENSIONS GND CH1 CH2 1.00.15 GND 0.1min. 0.250.1 1.20.15 0.1min. 0.50.1 0.650.05 0.15min. 0.350.1 Dimensions in mm RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 0.65 GND 0.3 0.5 GND CH2 0.6 0.25 CH1 0.9 1.8 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_signal_03.fm (6/11) E M C C o m p o n e n t s MEA-PE series MEA1210PE Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Capacitance (pF) Cutoff frequency (MHz)typ. 40 36 22 210 220 250 Insertion loss 20dB frequency range (MHz) 470 to 3000 470 to 3000 470 to 3000 Measurement equipment Measurement item Product No. Capacitance 4294A Frequency characteristics N5230C Equivalent measurement equipment may be used. Rated voltage (V)max. Rated current (mA)max. Part No. 6.3 6.3 6.3 100 100 100 MEA1210PE400T MEA1210PE360T MEA1210PE220T Manufacturer Agilent Technologies Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 10 Insertion loss (dB) 20 30 40 50 220 60 400 70 10 100 1000 360 10000 Frequency (MHz) Measurement equipment Product No. Manufacturer N5230C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_signal_03.fm (7/11) E M C C o m p o n e n t s MEA-PE series MEA1608PE Type 0.20.1 CH1 CH2 CH3 CH4 GND GND 0.40.05 0.40.05 0.50.1 0.40.05 0.80.1 1.60.1 0.05min. SHAPE & DIMENSIONS 0.15min. 0.20.1 Dimensions in mm RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 2.0 CH1 0.15 to 0.2 CH3 CH4 0.15 GND 0.5 0.35 CH2 GND 0.025 0.2 to 0.25 0.4 0.04 0.35 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_signal_03.fm (8/11) E M C C o m p o n e n t s MEA-PE series MEA1608PE Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Capacitance (pF) Cutoff frequency (MHz)typ. 36 27 22 15 220 240 250 270 Insertion loss 20dB frequency range (MHz) 470 to 3000 470 to 3000 470 to 3000 -- Measurement equipment Measurement item Product No. Capacitance 4294A Frequency characteristics N5230C Equivalent measurement equipment may be used. Rated voltage (V)max. Rated current (mA)max. Part No. 6.3 6.3 6.3 6.3 100 100 100 100 MEA1608PE360T MEA1608PE270T MEA1608PE220T MEA1608PE150T Manufacturer Agilent Technologies Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 10 Insertion loss (dB) 20 30 40 50 150 270 60 360 220 70 80 10 100 1000 10000 Frequency (MHz) Measurement equipment Product No. Manufacturer N5230C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_signal_03.fm (9/11) E M C C o m p o n e n t s MEA-PE series MEA2010PE Type 2.00.15 0.250.1 CH1 CH2 CH3 CH4 GND GND 0.50.1 0.50.1 0.70.1 0.50.1 1.00.15 0.10min. SHAPE & DIMENSIONS 0.15min. 0.250.1 Dimensions in mm RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 2.80 1.60 CH1 CH3 CH4 GND 0.50 0.25 1.80 0.60 0.25 GND CH2 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_signal_03.fm (10/11) E M C C o m p o n e n t s MEA-PE series MEA2010PE Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Capacitance (pF) Cutoff frequency (MHz)typ. 40 36 22 15 210 220 250 270 Insertion loss 20dB frequency range (MHz) 470 to 3000 470 to 3000 470 to 3000 --- Measurement equipment Measurement item Product No. Capacitance 4294A Frequency characteristics N5230C Equivalent measurement equipment may be used. Rated voltage (V)max. Rated current (mA)max. Part No. 6.3 6.3 6.3 6.3 100 100 100 100 MEA2010PE400T MEA2010PE360T MEA2010PE220T MEA2010PE150T Manufacturer Agilent Technologies Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 Insertion loss (dB) 10 20 30 40 150 50 400 60 10 360 100 1000 220 10000 Frequency (MHz) Measurement equipment Product No. Manufacturer N5230C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_signal_03.fm (11/11) E M C C o m p o n e n t s MEA-PE series Packaging style REEL DIMENSIONS o60min. 2.00.5 1.0 8.4 +2.0 -0.0 o130.2 o210.8 14.4max. o1802.0 Dimensions in mm TAPE DIMENSIONS 1.750.1 t B 3.50.05 4.00.1 4.00.1 A MEA1608PE 8.00.3 2.00.05 1.5 +0.1 0 MEA1210PE, MEA2010PE K K Dimensions in mm Type MEA1210PE MEA1608PE MEA2010PE A 1.200.05 1.000.10 1.150.05 160min. Taping B 1.450.05 1.800.10 2.150.05 K 0.73max. 1.0max. 1.0max. t -- 0.250.05 -- 200min. 300min. Drawing direction MEA1210PE MEA1608PE MEA2010PE Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_signal_03.fm