PINS 4&5 | 1000pF ; CKV P6 P3 OO@ @Q/@ @|@ Pe Pl ELECTRICAL SPECIFICATIONS: 1.0 TURNS RATIO P8-P6-P7) + (J6-J3) CP2-P3-P1l) + CJe2-J1) 2.0 INDUCTANCE P7-P8) P1-P2) 3.0 LEAKAGE INDUCTANCE P8-P7 (WITH J6 AND J3 SHORT? Pe-P1 WITH Je AND Ji SHORT) ICT : 4.0 INTERWINDING CAPACITANCE P8,P6,P7>) TO (J6,J3) CP3,P2,P1l TO (J2,J1) 3.0 DC RESISTANCE (J1-J2> (P8-P7> + 1CT + 14 37% 1 1CT + 1 3% + 0.3 MAX, @ 1MHz + 0.3 MAX, @ 1MHz : 2Spf MAX @ 1MHz ' 25pf MAX, @ 1MHZ : L2 ohms Max, : 12 ohms Max. NOTES 1.0 PINS WITHOUT ELECTRICAL CONNECTION ARE OMITTED. + S3S0uUH MIN, @ O1V , 100KHz, 8mA DC Bias 1 350uH MIN, @ 0.1V, 100KHz, 8mA DC Bias InNet Technologies Inc. http://www.innettech.com Stewart Connector Systems http://www.stewartconnector.com SHEET 1 of 4 DRAWING NO. SI AQO C 9 046.0 RETURN LUSS: 1MHz TO 3O0MHz 60MHz TO 80MHz 7.0 VOLTAGE WITHSTAND: Jl, Je> TO P1, P2d (J3, J6> TO P8,P7) 8.0 INSERTION LOSS: 100KHz TO 100MHz 9.0 RISE TIME: OUTPUT VOLTAGE = 1 V peak PULSE WIDTH= 112enS 10.0 CROSS TALK: 1MHz TO 100MHz 11.0 COMMON TO COMMON MODE ATTENUATION: 1MHz TO 100MHz 180B MIN. 12cB MIN. 1500 VAC 1500 VAC 1.1 dB MAX 3.0 nS MAX 3.0 nS MAX 35 dB TYP 450B TYP InNet Technologies Inc. http://www.innettech.com Stewart Connector Systems http://www.stewartconnector.com DB of 4 DRAWING NO. SI _ A 0 0 eC 9 04BICOLOR LED POLARITY 01720091 /CT720074/240079 *2,354 [59.79] MAX t x< = # # io CAAA AA) q q r q q q q q } PRR ch LED GRN/YEL (4 PLCS) LED YEL (4 PLCS) 4.005 LED SPECIFICATION yettow GREEN POWER DISSIPATION: 105mW 105mW FORWARD VOLTAGE *: TYP: = 2.1V 2.2V MAX: 2.5V 2.6V INTENSITY @ 10ma : 2-8MCD 8-32MCD WAVELENGTH : 590nm 565nm #* 585 [14.86] (8) Ref. | #,148 [3.75] (12) Ref. NOTES: TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS DIMENSIONS SHOWN WITH * TO BE CENTRAL ABOUT CENTER LINE "**" ON DIMENSION INDICATES HIGHEST POINT OF BEAM DIMENSIONS SHOWN ARE SUBJECT TO CHANGE WITHOUT NOTICE a { Te PIN NOT ELECTRICALLY CONNECTED MAYBE OMITTED. 2 SEE ELECTRICAL DRAWING FOR OMITTED PINS. > | STANDARD 50 MICRO-INCH SELECTIVE GOLD PLATING. I TM tht = L 425 +.005 BOTTOM SURFACE OF JACK f 028 [0.64] (PCB SURFACE) ~ -- .550 [13.97] TYP 275 [6.99] Lt TOL NONACCUM .050 [1.27] TYP =o 550 [13.97] TYP + Zz | TOL NONACCUM le ||+.025 [0.64] 22 F 100 [2.54] TYP oe 9.035 ~\ FOL NON ACOUM <2 < 8 Ko} oO ws cD, a f = 6 oo 128 [325] eee Po goo tts dole PO sae 9 ik 125 [3.18] db bh a db a ab las ab a bh a ad | Y YY vO NY YY \ YY vy YY YY | PIN 1 9.066 [1.68](3) Lh Or 4 oOo ~~ bos YOO TE doer roo o 4 b de ro os 8 a D+ D+ >t o 2 9.040 [1.02](16) 2 *2.100 [53.34] 4 T LL *.309 [7.85] TYP. *.509 [12.93] TYP. P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM COMPONENT SIDE TOLERANCE +.003 [0.08] UNLESS OTHERWISE SPECIFIED http://www.innettech.com http://www.stewartconnector.com InNet Technologies Inc. Stewart Connector Systems SHEET 3 OF 4 DRAWING NO. SI=40029 REV. 0 |1300 Y 1200 1100 [ 1000 900 800 f 700 [ 600 [ 500 400 [ 300 y/ 200 100 GRAMS OF FORCE / GROUNDING BEAM No wNY PANEL GROUNDING BEAM DEFLECTION S.0.S. = SUGGESTED OPENING SIZE <n ( L 000 (TOP OF PCB TO BOTTOM OF OPENING) -010 MAX. RADIUS(4) SUGGESTED PANEL OPENING CT720035x1 /24-001701 POINT OF CONTACT WITH PANEL = .080 => e .2/5 MAX a L THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE THE USER THE ABILITY TO HAVE REASONABLE JACK / PANEL CLEARANCES YET MAINTAIN RELIABLE GROUNDING CAPABILITY. THESE VARIABLES CAN BE ADJUSTED IN EITHER DIRECTION BUT MAY CARRY SOME CONSEQUENCES IN THE FORM OF LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. FORCE VALUES ON THE GRAPH ARE GENERAL AVERAGES TAKEN AT THE POINT OF CONTACT SHOWN ABOVE. THE SUGGESTED PANEL OPENING INCLUDES APPROXIMATELY .020 CLEARANCE ON THE SIDES AND TOP AND .005 ON THE BOTTOM. InNet Technologies Inc. http://www.innettech.com Stewart Connector Systems http://www.stewartconnector.com SHEET DRAWING NO. REV. 0 | 4 OF 4 SI-40029