0.36 (0.014") Xtreme-GuardTM ESD Suppressors 0.84 +/- 0.05 (0.033" +/- 0.002") Surface Mount Polymeric Electrostatic Discharge Suppressors 0.43 +/- 0.18 AXGD1 Series (0.017" +/- 0.007") Description Wave Solder Reflow Solder 0.51 (0.020") 0.76 (0.030") 3.30 (0.130") 3.05 (0.120") 1.27 (0.050") 1.27 (0.050") 0.76 (0.030") Features 0.76 (0.030") * AEC-Q200 Qualified * High ESD Rating up to 30kV Contact/Air Discharge * RoHS compliant, lead-free and halogen-free * Ultra-low capacitance * Low leakage current * Fast response time * Bi-directional * Withstands multiple Equivalent Circuits Equivalent Circuit 0402 and 0603 Components 2 1 Life Support Note: * Infotainment * High Speed Interface * High Frequency (i.e. RF, Antenna System, Ethernet, USB, DVI, LVDS) * Satellite Navigation Product Characteristics Lines Protected Component Package Available as Halogen-Free AXGD10402 1 0402 Yes AXGD10603 1 0603 Yes ESD strikes * Compatible with pick-and-place processes * Available in 1000, 5000, and 10000 piece reels (EIA-RS481) * High rated voltage up to 32V maximum * High operating temperature at 125C Applications Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. Part Number XTREME-GUARDTM ESD Suppressors protect sensitive electronic equipment against extreme ESD conditions, in very small 0402 and 0603 footprints. This product series is specifically designed to suppress fast-rising ESD transients up to 30kV while adding virtually no capacitance to the circuit, which helps preserve signal integrity and minimize data loss. It is RoHS compliant, halogen free and Pb free ESD Suppressor. * GPS Tracker * Car TV * Telematics Box * IVN (In Vehicle Navigation) * Portable Navigation Electrical Characteristics Specification AXGD10402 AXGD10603 30kV 30kV 30kV 30kV Trigger Voltage (typical) Clamping Voltage (typical) Trigger Voltage (typical) Clamping Voltage (typical) Rated Voltage (maximum) 250V 40V 150V 40V 24V max 400V 40V 300V 28V 32V max Capacitance (typical) 0.04 pF 0.09 pF <1nS <1nS ESD Capability: IEC 61000-4-2 Contact Discharge (typical) IEC 61000-4-2 Air Discharge (typical) Response Time Notes The ESD capability measured by direct and air discharge method is subject to testing equipment and conditions. Numerous factors could affect the reliability and reproducibility of the direct and air discharge test results. Measured per IEC 61000-4-2 8kV Direct Discharge Method Measured using 500V TLP Direct Discharge Method Measured at 250MHz Leakage Current (typical) <1nA @24V <1nA @24V 1000 1000 Some shifting in characteristics may occur when tested over multiple pulses min pulses min pulses at a very rapid rate Note: Testing performed on Littelfuse test setup as described in Typical Test Setup Section on page 4 of this document. ESD Pulse Withstand (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/21/20 Xtreme-GuardTM ESD Suppressors Surface Mount Polymeric Electrostatic Discharge Suppressors Signal Integrity: USB3.0 5Gbps Without AXGD Component Signal Integrity : USB3.0 5GbpsSignal Integrity : USB3.0 5Gbps Without XGD With AXGD Component Without XGD With XGD Device With XGD Device Signal Integrity : USB3.0 5Gbps Without XGD With XGD Device Signal Integrity : USB3.0 5Gbps Without XGD With XGD Device Signal Integrity : USB3.1 10Gbps Signal Integrity : USB3.1 10Gbps XGD SignalWithout Integrity: USB3.1Without 10Gbps XGD Without AXGD Component Signal Integrity : USB3.1 10Gbps Without XGD With XGD Device With XGD Device With AXGD Component Signal Integrity : USB3.1 10Gbps Without XGD With XGD Device Typical Component Capacitance With XGD Device Typical ESD Response Capacitance (pF) 1.00 AXGD10603 AXGD10402 0.10 AXGD10603 AXGD10402 0.01 100 1,000 10,000 Frequency (MHz) (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/21/20 Xtreme-GuardTM ESD Suppressors Surface Mount Polymeric Electrostatic Discharge Suppressors Physical Specifications Environmental Specifications Materials Body: Glass Epoxy Terminations: Copper/Nickel/Tin Solderability MIL-STD-202, Method 208 Soldering Parameters Wave solder - 260C, 10 seconds maximum Reflow solder - 260C, 30 seconds maximum AEC-Q200 AEC-Q200 RevD Table 10 Operating and Storage Temperature -65C to +125C 0402 and 0603 series: 85C, 85% RH, 1000 hours 40C, 95% RH, 1000 hours MIL-STD-202, Method 107, -65C to 125C, 30 min. cycle, 10 cycles MIL-STD-202, Method 201, (10 to 55 to 10 Hz, 1 min. cycle, 2 hrs each in X-Y-Z) MIL-STD-202, Method 215 Moisture Resistance Design Consideration Thermal Shock Because of the fast rise-time of the ESD transient, proper placement of XTREME-GUARDTM suppressors are a key design consideration to achieving optimal ESD suppression. The components should be placed on the circuit board as close to the source of the ESD transient as possible. Install XTREME-GUARDTM suppressors (connected from signal/ data line to ground) directly behind the connector so that they are the first board-level circuit component encountered by the ESD transient. Caution: This device should not be used in Power Bus applications. Vibration Chemical Resistance Soldering Parameters Pb - Free assembly Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 seconds Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow tP TP - Temperature (TL) (Liquidus) 217C - Temperature (tL) 60 - 150 seconds Peak Temperature (TP) 260C Time within 5C of actual peak Temperature (tp) 10 - 30 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes max Ramp-up TL tL T S(max) Temperature Reflow Condition Ramp-dow Ramp-down Preheat T S(min) tS 25 time to peak temperature Time Based on IPC/JEDEC J-STD-020 Packaging Part Number Quantity & Packaging Code Quantity Packaging Option Packaging Specification AXGD10402 KR 10000 Tape & Reel (7" reel) EIA RS-481-1 (IEC 286, part 3) AXGD10603 MR 1000 Tape & Reel (7" reel) EIA RS-481-1 (IEC 286, part 3) AXGD10603 NR 5000 Tape & Reel (7" reel) EIA RS-481-1 (IEC 286, part 3) (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/21/20 Xtreme-GuardTM ESD Suppressors Surface Mount Polymeric Electrostatic Discharge Suppressors Dimensions 0402 Component 0603 Component Dimensions: mm (inch) Reference Dimensions: 1.02 0.05 (0.040" 0.002") Dimensions: mm (inch) Reference Dimensions: 1.68 0.08 (0.066" 0.003") 0.46 0.05 (0.018" 0.002") 0.46 0.05 (0.018" 0.002") 0.51 0.05 (0.020" 0.002") 0.23 0.10 (0.009" 0.004") 0.84 0.05 (0.033" 0.002") 0.43 0.18 (0.017" 0.007") Reflow Solder Only Reflow Solder Only Wave Solder Reflow Solder 0.381 (0.015") 0.381 (0.015") 1.55 (0.061") 1.55 (0.061") 3.05 (0.120") .584 (0.023") 0.51 (0.020") 0.76 (0.030") 3.30 (0.130") .584 (0.023") 1.27 (0.050") 0.559 (0.022") 1.27 (0.050") 0.559 (0.022") 0.76 (0.030") Recommended Pad Layout Recommended Pad Layout 0.76 (0.030") Tape and Reel Specifications Tt Description Ds Dd Pd Ph Ps Ct Tw Pw Typical Test Setup 0402 Series (mm) 0603 Series (mm) Ct - Cover tape thickness 0.05 0.05 Dd - Drive hole diameter 1.50 1.50 Ds - Drive hole spacing 4.00 4.00 Pd - Pocket depth 0.56 0.58 Ph - Pocket height 1.14 1.85 Ps - Pocket spacing 2.00 4.00 Pw - Pocket width 0.62 1.02 Tt - Carrier tape thickness 0.65 0.65 Tw - Carrier tape width 8.00 8.00 FARADAY CAGE COMPUTER AGILENT INFINIIUM 1.5 GHz 8 GS/s 30dB PASTERNAK ATTENUATOR PE7025-30 TEKTRONIX LOW CAP PROBE 6158 (20x TIP) QUADTECH 1865 RESISTANCE METER Part Numbering System AXGD Lead-Free Auto Grade Xtreme GuardTM ESD Suppressors Lines Protected: 1 = 1 line RESISTANCE TEST FIXTURE 1 0603 NR Quantity & Packaging Code: MR = 1000 pieces, tape & reel NR = 5000 pieces, tape & reel KR = 10,000 pieces, tape & reel Device Size Code: 0402 = 0402 (1005) 0603 = 0603 (1608) ESD TEST FIXTURE TEST BOARD W/ DUT ESD PULSE GENERATOR Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/21/20