RP100-4815S - Recom International Power

www.recom-international.com 149

April-2005

100 Watt

Isolated

Single &&

Dual Output

INNOLINE

DC/DC-Converter

RP100-S_DI

Series

●Single Output up to 25A

Dual Outputs Total Power up to 100W

●Input/Output 1.6kVDC Isolation

●Adjustable Output Voltage

●Under-Voltage Lockout

●No Minimum Load

●Industry Standard Footprint

●Fixed Operating Frequency

●Halt Tested

●Compact 61.0 x 57.91 x 12.7mm Package

●High Efficiency to 90%

Features

Selection Guide

Notes:

Part Input Output Output Line Load Input Efficiency

Number Voltage Voltage Current Regulation Regulation Current(8) (9)

SSiinnggllee OOuuttppuutt(VDC) (VDC) (A) (mV) (mV) (A) %

RP100-481.8S 36 – 75 1.8 25 4 6 1.157 86

RP100-482.5S 36 – 75 2.5 25 5 8 1.608 87

RP100-483.3S 36 – 75 3.3 25 7 10 2.022 90

RP100-4805S 36 – 75 5 20 10 15 2.480 90

RP100-4815S 36 – 75 15 6.66 30 45 2.507 90

Part Input Output Output Line Load Input Efficiency

Number Voltage Voltage Current Regulation Regulation Current(8) (9)

V1 / V2 I1 / I2 V1 / V2 V1 / V2

DDuuaall OOuuttppuutt(VDC) (VDC) (A) (mV) (mV) (A) %

RP100-483.305DI 36 – 75 5 / 3.3 20 / 25 25 / 16.5 25 / 16.5 2.39 87

RP100-482.505DI 36 – 75 5 / 2.5 20 / 25 25 / 12.5 25 / 12.5 2.45 85

RP100-482.53.3DI 36 – 75 3.3 / 2.5 25 / 25 16.5 / 12.5 16.5 / 12.5 2.44 85

1. Maximum output deviation is 10% inclusive of remote sense. If remote sense is not being used,

the +Vsense should be connected to its corresponding +Vout and likewise the -Vsense should be connected

to its corresponding -Vout.

2. Single: Measured with a 1uF M/C and a 10uF T/C.

Dual: For each outputs.

3. An external filter capacitor is required for normal operation.

The capacitor should be capable of handing 1A ripple current for 48V models.

RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90mΩ.

4. Single: The negative / positive logic and length are optional ( see table ).

The pin voltage is referenced to negative input.

Dual: The ON/OFF control function. There are positive logic ( standard ) and negative logic ( option ).

The pin voltage is referenced to negative input.

To order negative logic ON/OFF control add the suffix-N. ( Ex:RP100-483.305I/N )

5. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40°C.

( Ground fixed and controlled environment )

6. Heat sink is optional and P/N: 7G-0021, 7G-0022, 7G-0023, 7G-0024.

7. The RP100 meets level A and level B conducted emissions only with external components connected before

the input pin to the converter.

8. Maximum value at nominal input voltage and full load.

9. Typical value at nominal input voltage and full load.

The dual efficiency test condition: RP100-483.305DI @ 5V/12A and 3.3V/12A

RP100-482.505DI @ 5V/12A and 2.5V/16A

RP100-482.53.3DI @ 3.3V/18A and 2.5V/16A

10. BASEPLATE GROUNDING: Base-plate should be grounded at one of four screw bolts prior to operation.

11. The converter is provided by basic insulation.

12. “NN” for Negative remote ON/OFF.

13. “PP” for Positive remote ON/OFF.

150 www.recom-international.comApril-2005

RP100-S_DI

Series

Specifications (refer to the standard application circuit, Ta: 25°C)

INNOLINE

DC/DC-Converter

Input Voltage Range 36-75VDC 48V nom.

Over-Voltage Lockout Start-up Voltage Dual 76.5V typ.

Over-Voltage Lockout Shuntdown Voltage Dual 78.5V typ.

Unde-Voltage Lockout Start-up Voltage Single 34V typ.

Dual 35V typ.

Unde-Voltage Lockout Shuntdown Voltage Single 32V typ.

Dual 33V typ.

Input Filter (Note 3) L-C type

Input voltage variation dv/dt 5V/ms max

(Complies with ETS300 132 part4.4)

Input Surge Voltage 100mS max Single 100VDC

Start up time Nominal Vin and constant resistive load Single 25mS typ.

Input Reflected-Ripple Current Single 20mAp-p

(5Hz to 20Hz, 12uH Source inpedance)

Remote ON/OFF (Note 4)

Single (Positive logic) ON=Open or 3.5V < Vr < 15V, IIN=50µA max.

OFF=Short or 0V < Vr < 1.2V, IIN=1mA max.

Single (Negative logic) ON=Short or 0V < Vr < 1.2V, IIN=1mA max.

OFF=Open or 3.5V < Vr < 15V, IIN=50µA max.

Dual (Positive logic) ON=Open or 3.5V < Vr < +Vin,

OFF=Short or Vr < 1.2V,

Dual (Negative logic) ON=Short or 3.5V < Vr < +Vin,

OFF=Open or Vr < 1.2V.

Continuous Output Power 100W max.

Output Voltage Accuracy (Full load and nominal Vin) Single ±1.5%

Dual ±1.0%

Output Voltage Adjustment (Note 1) Single +10%, -20%

Dual ±10%

Minimum Load 0%

Line Regulation LL to HL at FL See table

Load Regulation Single 0% to 100% FL

Dual 0% to 100% FL See table

Dual for each Outputs

Remote Sense (Note 1) 10% of Vout

Ripple and Noise 20MHz bandwidth (Note 2) 100mVp-p

Temperature Coefficient ±0.02%/ºC

Transient Response Recovery Time (25% load step change) 200us

Over Voltage Protection threshold (Hiccup) Single & Dual 115% ~ 130% of Vout

2.5V 3.0V

3.3V 3.9V

5V 6.2V

Over Current Protection threshold 110% ~ 140% of Iout Rated

Short Circuit Protection Hiccup, Automatic recovery

Efficiency (at nominal input voltage, full load) up to 90%

Continued next page

www.recom-international.com 151

April-2005

Isolation Voltage Input to Output 1.600VDC min.

Input to Case 1.000VDC min.

Output to Case 1.000VDC min.

Isolation Resistance Single 107ohms min.

Dual 109ohms min

Isolation Capacitance Single 2.500pF max.

Dual 1.500pF max.

Operating Frequency 300KHz typ.

Operating Base-plate Temperature Range ( Note 6 ) -40ºC to +100ºC

Over Temperature Protection Single 110°C

Dual for Base-plate 105°C

Storage Temperature Range -55°C to +125°C

Humidity max., Non-condensing 95%

Thermal Shock MIL-STD-810D

Vibration 10 ~ 55Hz 2G, 3minutes period, 30minutes analog X, Y and Z

Conducted Emissions EN55022 (Note 7) Level A

EN55022 (Note 7) Level B

Radiated Emisssions EN55022 Level A

ESD EN61000-4-2 Perf. Criteria2

Radiated Immunity EN61000-4-3 Perf. Criteria2

Fast Transient EN61000-4-4 Perf. Criteria2

Surge EN61000-4-5 Perf. Criteria2

Conducted Immunity EN61000-4-6 Perf. Criteria2

Case Material Dual Non-conductive black plastic

Base material Aluminum base-plate

Potting material Dual Silicon (UL94-V0)

Weight Single 55g

Dual 105g

MTBF ( Note 6 ) Single 2 x 106hrs

1.004 x 106hrs

Specifications (refer to the standard application circuit, Ta: 25°C)

INNOLINE

DC/DC-Converter RP100-S_DI

Series

152 April-2005

Characteristics

RP100-S_DI

Series

www.recom-international.com

Output Power (%) Ta=25°C

Efficiency (%)

100

30 60 80

10 100

20 40 50 70 90

Efficiency vs Output Load

Ambient Temperature (°C)

Output Power (%)

110

-40 100

-20 020 40 80

12 3 4

1.) LFM590

2.) LFM400

3.) LFM200

4.) LFM20

48V Input Without Heatsink

Ambient Temperature (°C)

Output Power (%)

110

-40 100

-20 020 40 80

12 34

1.) LFM590

2.) LFM400

3.) LFM200

4.) LFM20

48V Input With Heatsink (7G-0022)

INNOLINE

DC/DC-Converter

www.recom-international.com 153

April-2005

Trim Up

Trim Down

Product Options Table

External Output Trimming

Output can be externally trimmed by using the method

shown below.

See application notes for values.

Package Style and Pinning (mm)

INNOLINE

DC/DC-Converter

3rd angle

projection

60.96

57.91

Bottom View

50.80

35.56 15.24

10.16

12.70

5.08

48.26

Side View

17.78

25.40

4xM3 x 0.5 ( Note 10)

XX.X ± 0.5 mm

XX.XX ± 0.25 mm

Pin pitch tolerance 0.35mm

Pin Connections

Pin # Function Pin Ø

1 –Vin 1.016 mm

2 Case 1.016 mm

3 Remote ON/OFF 1.016 mm

4 +Vin 1.016 mm

5 –Vout 2.032 mm

6 –Vsense 1.016 mm

7 Trim 1.016 mm

8 +Vsense 1.016 mm

9 +Vout 2.032 mm

OOppttiioonnSSuuffffiixx

Negative remote ON/OFF logic, 0.20” pin length (standard)

Negative remote ON/OFF logic, 0.145” pin length L

Negative remote ON/OFF logic, 0.11” pin length K

Positive remote ON/OFF logic, 0.20” pin length P

Positive remote ON/OFF logic, 0.145” pin length S

Positive remote ON/OFF logic, 0.11” pin length M

EExxaammppllee:: RRPP110000--448833..33SS//PP

RP100-S_DI

Series

Single Output

154 www.recom-international.comApril-2005

60.96

57.91

Bottom View

50.80

35.56

15.24 10.16

25.40

40.64

12.70

5.08

48.26

Side View

4xM3 x 0.5 ( Note 10)

Trim Up

Trim Down

9(6)

10(7)

8(5)

Product Options Table

External Output Trimming

Output can be externally trimmed by using the method

shown below. See application notes for values.

( ) for V2 output trim

Package Style and Pinning (mm)

INNOLINE

DC/DC-Converter

3rd angle

projection

XX.X ± 0.5 mm

XX.XX ± 0.25 mm

Pin pitch tolerance 0.35mm

Pin Connections

Pin # Function Pin Ø

1 –Vin 1.016 mm

2 Case 1.016 mm

3 Remote ON/OFF 1.016 mm

4 +Vin 1.016 mm

5 +V2 2.032 mm

6 –V2 (Com) 2.032 mm

7 V2 Trim 1.016 mm

8 +V1 2.032 mm

9 +V1 (Com) 2.032 mm

10 V1 Trim 1.016 mm

OOppttiioonnSSuuffffiixx

Negative remote ON/OFF logic, 0.20” pin length (standard)

Negative remote ON/OFF logic, 0.145” pin length L

Negative remote ON/OFF logic, 0.11” pin length K

Positive remote ON/OFF logic, 0.20” pin length P

Positive remote ON/OFF logic, 0.145” pin length S

Positive remote ON/OFF logic, 0.11” pin length M

EExxaammppllee:: RRPP110000--448833..330055II//NN

RP100-S_DI

Series

Dual Output