Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model BD2130J5050A00
Rev A
Ultra Low Profile 0805 Balun
50Ω to 50Ω Balanced
Description
The BD2130J5050A00 is a low profile sub-miniature balanced to unbalanced
transformer designed for differential inputs and output locations on next generation
wireless chipsets in an easy to use surface mount package covering 802.11b+g+n.
The BD2130J5050A00 is ideal for high volume manufacturing and is higher
performance than traditional ceramic and lumped element baluns. The
BD2130J5050A00 has an unbalanced port impedance of 50Ω and a 50Ω balanced
port impedance. This transformation enables single ended signals to be applied to
differential ports on modern semiconductors. The output ports have equal amplitude
(-3dB) with 180 degree phase differential. The BD2130J5050A00 is available on
tape and reel for pick and place high volume manufacturing.
Detailed Electrical Specifications*: Specifications subject to change without notice.
ROOM (25°C)
Parameter Min. Typ. Max Min. Typ. Max Unit
Frequency 2.4 2.5 2.1 3.0 GHz
Unbalanced Port Imp. 50 50 Ω
Balanced Port Imp.** 50 50 Ω
Return Loss 12 17 10 12 dB
Insertion Loss*** 0.75 0.9 1.0 1.2 dB
Amplitude Balance 0.45 0.65 0.7 1.0 dB
Phase Balance 2 5 2 5 Degrees
Power Handling 2 2 Watts
Features:
• 2.1 – 3.0 GHz
• 0.7mm Height Profile
• 50 Ohm to 2 x 25 Ohm
• 802.11 b & g +n Compliant
• Low Insertion Loss
• DCS, PCS & UMTS
• Input to Output DC Isolation
• Surface Mountable
• Tape & Reel
• Non-conductive Surface
• RoHS Compliant
Operating Temperature -55 +85 -55 +85 ºC
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
Outline Drawing
Mechanical Outline
Dimensions are in Inches [Millimeters]
Tolerances are Non-Cumulative
.049±.004
[1.25±0.10]
.079±.004
[2.00±0.10]
1 2 3
6 5 4
Bottom View (Far-side)Side ViewTop View (Near-side)
.027±.002
[0.70±0.05]
6X .012
[0.30]
+ RF GND
Pin
3
6
1
2
4
5
Designation
Unbalanced Port
GND / DC Feed
Balanced Port
Balanced Port
GND
NC
Orientation
Marker Denotes
Pin Location
Orientation
Marker Denotes
Pin Location
.026 [0.65]
6X .009
[0.22]
.039 [0.98]
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model BD2130J5050A00
Rev A
Typical Broadband Performance: 0 GHz. to 6.0 GHz.
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model BD2130J5050A00
Rev A
Typical Performance: 2400 MHz. to 2500 MHz.
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model BD2130J5050A00
Rev A
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be
used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet
published specifications.
All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical
and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC.
An example of the PCB footprint used in the testing of these parts is shown below. An example of a DC-biased
footprint is also shown below. In specific designs, the transmission line widths need to be adjusted to the unique
dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances.
No Bias Footprint
0805 Standard Mounting Footprint
Dimensions are in Inches [Millimeters]
.029
[0.73]
6X .002
[0.05]
6X .011
[0.27]
4X .012
[0.30]
Plated thru
hole to
ground
3X Transmission
Line
Circuit Pattern
Footprint Pad (s)
Solder Resist
6X .014
[0.35]
Part Orientation (Top View)
DC Bias Footprint
DC Bias
.026
[0.66]
4X .012
[0.30]
6X .013
[0.33]
6X .016
[0.35]
Part Orientation (Top View)
0805 DC Bias Mounting Footprint
Dimensions are in Inches [Millimeters]
6X .002
[0.05]
Plated thru
hole to
ground
3X Transmission
Line
Circuit Pattern
Footprint Pad (s)
Solder Resist
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Model BD2130J5050A00
Rev A
Packaging and Ordering Information
Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order
quantities are 4000 per reel. See Model Numbers below for further ordering information.
B
ØA ØC
REEL DIMENSIONS (inches [mm])
ØA
B
ØC
0.32 [8.0]
2.0 [50.8]
7.00 [177.8]
4000
QUANTITY/REEL
TABLE 1
ØD
0.512 [13.0]
ØD
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model BD2130J5050A00
Rev A
