The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. General-purpose Multi-Contact Circular Waterproof Connectors RM-W Series Plug _ straight O23 O21.5 57 Long backshell O21.5 48 Overview High performance waterproof circular connectors and cable assemblies used in variety of applications requiring high reliability, ease of assembly and small size. Short backshell Plug _ Right angle Features 41 Receptacles : Waterproof types with front, back or flange panel mounting. All types with 2, 3, 4, 8, 10, 12, 15, 20, 31, 40, 55 contacts. Contacts in 2 plating types: gold or silver. 2. Dust and water protection When fully mated, the connector meet requirements of IP67 (48 hours at depth of 1.8 m) (Single-body waterproof receptacles also meet requirements of IP67.) O23 360 Cable exit Cable : Available in 3 types - straight / long back shell, straight / short back shell, right angle back shell. 360 Plugs 40 1. Variety of types 3. Cable exit in 360 directions The right-angle plugs permit exiting of the cable over a 360-degree range in any direction. Applications Base stations, factory automation equipment, robotic equipment, exploration and construction equipment, research instrumentation, variety of industrial and measuring instruments. Any other applications requiring high reliability waterproof circular connectors. 2006.1 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Product Specifications (RM15WT size products) 600V AC, 840V DC (2 pos.) 500V AC, 700V DC (3, 4, 8 pos.) Voltage rating 350V AC, 490V DC (10 pos.) 350V AC, 490V DC (12 pos.) Rating 10A (2, 3, 4 pos.) Current rating 5A (8, 10, 12 pos.) Operating temperature range (Note 1) -25c to +85c Storage temperature range (Note 2) -25c to +85c Characteristic 1. Contact resistance 2. Insulation resistance Specification Conditions 2 m o max.(2, 3, 4 pos.) 4 m o max.(8, 10, 12 pos.) 1000 M o min 1A DC 500V DC 1800V AC/one minute (2 pos.) 2000V AC/one minute (3 pos.) 1500V AC/one minute (4, 8 pos.) 1000V AC/one minute (10, 12 pos.) Frequency: 10 to 55Hz, single amplitude of 0.75mm,for 3 hours in 3 axis. Acceleration of 490m/s 2 , 11ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. 3. Withstanding voltage No flashover or insulation breakdown. 4. Vibration No electrical discontinuity for 10s max. 5. Shock No electrical discontinuity for 10s max. 4 m o max.(2, 3, 4 pos.) 6. Durability (insertion/withdrawal) 8 m o max.(8, 10, 12 pos.) 2000 cycles 7. Temperature cycle Insulation resistance: 100 M o min. 8. Humidity Insulation resistance: 100 M o min. (Dray state) Temperature : -55c Room temperature +85c Room temperature Time : 30 10 to 15 30 10 to 15 (Minutes) 5 cycles 96 hours at temperature 0f 40c and humidity 0f 90% to 95%. Complete dust protection. No water penetration when submerged for 48 hours at the depth of 1.8 meter. 9. Water / dust protection 0When mated with corresponding connector. Note 1: Includes temperature rise caused by the current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating temperature range and humidity range Note 2: covers non-conducting condition of installed connectors in storage, shipment or during transportation. Materials Item Material Finish Remarks Body Zinc alloy, brass, pliable PVC Chrome plated or nickel plated ------------------- Insulator Diallyl phthalate, PBT Color: Black UL94V-0 Contacts Brass, phosphor bronze, or copper alloy Silver plated or gold plated ------------------- Gasket SIR (black or red), or NBR (gray) Color: black or red (SIR), color: gray (NBR) ------------------- Note: Do not mix different contact plating. Ordering Information * * - 2 P (* *) RM 15 W T P* 1 2 3 4 5 6 1 Series name : RM-W 5 Number of Contacts 2 Shell size 6 Contact type 3 Lock type T : Screw Lock 4 Connector type 2 1 7 P : Male contact S : Female contact 7 Plating P : Plug (71) : Silver plated R : Receptacle (72) : Gold plated The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Plugs - straight, long back shell Wrench opening dimension of 18 mm RM15WTPZA-10S(71) M200.75 13 O21.5 2 O15.2 M191 45.3 (shown one example) [Specification number] (**), -** (71) : Silver plated contacts (72) : Gold plated contacts Part Number CL No. Number of Contacts Weight RoHS Part Number CL No. Number of Contacts Weight RoHS RM15WTPZA-2P() 109-1734-5- 2 43g RM15WTPZA-2S() 109-1729-5- 2 45g RM15WTPZA-3P( 72 ) 109-1602-4- 72 3 45g RM15WTPZA-3S() 109-1601-1- 3 47g RM15WTPZA-4P() 109-1735-8- 4 44g RM15WTPZA-4S() 109-1730-4- 4 45g RM15WTPZA-8P() 109-1736-0- 8 43g RM15WTPZA-8S() 109-1731-7- 8 45g RM15WTPZA-10P() 109-1737-3- 10 44g RM15WTPZA-10S() 109-1732-0- 10 45g RM15WTPZA-12P() 109-1738-6- 12 44g RM15WTPZA-12S() 109-1733-2- 12 45g YES YES Applicable Strain reliefs External cable clamp + internal, self-tightening JR16WCC-10(72) M200.75 A O23 Wrench opening dimension of 21 mm Drive screw(2) 17.5 (shown one example) Part Number CL No. A Weight JR16WCC-4(72) 114-2052-6-72 4 17.5g JR16WCC-6(72) 114-2053-9-72 6 17.5g JR16WCC-8(72) 114-2054-1-72 8 17.5g RoHS YES Part Number CL No. A Weight JR16WCC-10(72) 114-2055-4-72 10 17.5g JR16WCC-11(72) 114-2154-6-72 11 17.5g JR16WCC-12(72) 114-2056-7-72 12 17.5g RoHS YES Internal, self tightening JR16WCCA-10(72) M200.75 A O23 Wrench opening dimension of 21 mm 8 (shown one example) Part Number CL No. A Weight JR16WCCA-4(72) 114-2076-4-72 4 16g JR16WCCA-6(72) 114-2077-7-72 6 16g JR16WCCA-8(72) 114-2078-0-72 8 16g RoHS YES Part Number CL No. A Weight JR16WCCA-10(72) 114-2079-2-72 10 16g JR16WCCA-11(72) 114-2155-9-72 11 16g JR16WCCA-12(72) 114-2080-1-72 12 16g RoHS YES Notes : 1. Cable jacket diameter:Use A 0.2mm 2. When using the self-tightening strain relief verify the cable pull force requirements. 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Plugs - Straight, short back shell Wrench opening dimension of 18 mm RM15WTPZ-10S M160.75 13 O15.2 2 O21.5 M191 36.3 (shown one example) [Specification number] (**), -** (71) : Silver plated contacts (72) : Gold plated contacts Part Number CL No. Number of Contacts Weight RoHS Part Number CL No. Number of Contacts Weight RoHS RM15WTPZ-2P() 109-1616-9- 2 32g RM15WTPZ-2S() 109-1611-5- 2 34g RM15WTPZ-3P() 109-1622-1- 3 34g RM15WTPZ-3S() 109-1621-9- 3 36g RM15WTPZ-4P() 109-1617-1- 4 33g RM15WTPZ-4S() 109-1612-8- 4 34g RM15WTPZ-8P() 109-1618-4- 8 32g RM15WTPZ-8S() 109-1613-0- 8 34g RM15WTPZ-10P() 109-1619-7- 10 33g RM15WTPZ-10S() 109-1614-3- 10 34g RM15WTPZ-12P() 109-1620-6- 12 33g RM15WTPZ-12S() 109-1615-6- 12 34g YES YES Applicable Strain reliefs External cable clamp + internal, self-tightening JR13WCC-10(72) M160.75 A O20 Wrench opening dimension of 17 mm Drive screw(2) 17 (shown one example) Part Number CL No. A Weight JR13WCC-4(72) 114-2045-0-72 4 17g JR13WCC-5(72) 114-2046-3-72 5 17g JR13WCC-6(72) 114-2047-6-72 6 17g RoHS YES Internal, self tightening Part Number CL No. A Weight JR13WCC-7(72) 114-2048-9-72 7 17g JR13WCC-8(72) 114-2049-1-72 8 17g JR13WCC-9(72) 114-2050-0-72 9 17g JR13WCC-10(72) 114-2051-3-72 10 17g RoHS YES JR13WCCA-10(72) M160.75 A O20 Wrench opening dimension of 17 mm 7.5 (shown one example) 4 Part Number CL No. A Weight JR13WCCA-4(72) 114-2069-9-72 4 12g JR13WCCA-5(72) 114-2070-8-72 5 12g JR13WCCA-6(72) 114-2071-0-72 6 12g RoHS Part Number CL No. A Weight JR13WCCA-7(72) 114-2072-3-72 7 12g JR13WCCA-8(72) 114-2073-6-72 8 12g JR13WCCA-9(72) 114-2074-9-72 9 12g JR13WCCA-10(72) Notes : 1. Cable jacket diameter: Use A 0.2mm 2. When using the self-tightening strain relief verify the cable pull force requirements. 114-2075-1-72 10 12g YES RoHS YES The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Plugs - right angle Wrench opening dimension of 21.8 mm RM15WTLP-10S M160.75 O23 O15.2 19.15 Set screw(2) Hexagonal hole opposite side 1.27 mm (1.27HEX) M191 39.5 (shown one example) Part Number CL No. RM15WTLP-12P(71) 109-0997-9-71 Number of Contacts Weight RoHS 12 62.3g YES Part Number CL No. RM15WTLP-10S(71) 109-0999-4-71 Number of Contacts Weight RoHS 10 63.1g YES Notes : 1 Gasket material: NBR, body plating: nickel 2 Recommended set screw tightening torque: 0.2 to 0.3 N*m. HRS recommended tool: PB205/1.27(CL 150-0066-3) Applicable Strain reliefs External cable clamp + internal, self-tightening JR13WCC-10(72) M160.75 A O20 Wrench opening dimension of 17 mm Drive screw(2) 17 (shown one example) Part Number CL No. A Weight JR13WCC-4(72) 114-2045-0-72 4 17g JR13WCC-5(72) 114-2046-3-72 5 17g JR13WCC-6(72) 114-2047-6-72 6 17g RoHS YES Part Number CL No. A Weight JR13WCC-7(72) 114-2048-9-72 7 17g JR13WCC-8(72) 114-2049-1-72 8 17g JR13WCC-9(72) 114-2050-0-72 9 17g JR13WCC-10(72) 114-2051-3-72 10 17g RoHS YES Internal, self tightening JR13WCCA-10(72) M160.75 A O20 Wrench opening dimension of 17 mm 7.5 (shown one example) Part Number CL No. A Weight JR13WCCA-4(72) 114-2069-9-72 4 12g JR13WCCA-5(72) 114-2070-8-72 5 12g JR13WCCA-6(72) 114-2071-0-72 6 12g RoHS YES Part Number CL No. A Weight JR13WCCA-7(72) 114-2072-3-72 7 12g JR13WCCA-8(72) 114-2073-6-72 8 12g JR13WCCA-9(72) 114-2074-9-72 9 12g JR13WCCA-10(72) 114-2075-1-72 10 12g RoHS YES Notes : 1 Cable jacket diameter: Use A 0.2mm 2 When using the self-tightening strain relief verify the cable pull force requirements. 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Receptacles Front panel mount RM15WTRZ-10S(71) A 6 9 Wrench opening dimension of 18 mm O22 2 1 1 2 2 M191 (shown one example) [Specification number] (**), -** (71) : Silver plated contacts (72) : Gold plated contacts Part Number CL No. Number of Contacts RM15WTRZ-2P() 109-1631-2- 2 21 13g RM15WTRZ-3P() 109-1632-5- 3 22.1 15g RM15WTRZ-4P() 109-1633-8- 4 21 14g RM15WTRZ-8P() 109-1634-0- 8 20.65 13g RM15WTRZ-10P() 109-1635-3- 10 12 RM15WTRZ-12P() 109-1636-6- A Weight RoHS CL No. Number of Contacts RM15WTRZ-2S() 109-1637-9- 2 21.75 15g RM15WTRZ-3S() 109-1638-1- 3 22.1 RM15WTRZ-4S() 109-1639-4- 4 21.75 15g RM15WTRZ-8S() 109-1640-3- 8 21.6 15g 20.65 14g RM15WTRZ-10S() 109-1641-6- 10 21.6 15g 20.65 14g RM15WTRZ-12S() 109-1642-9- 12 21.6 15g YES Part Number A Weight RoHS 17g YES Notes : Recommended nut tightening torque: 3N*m Rear panel mount RM15WTRZA-10S(71) A 2 O27 24(HEX) 13 6.5 M191 M211 (shown one example) [Specification number] (**), -** (71) : Silver plated contacts (72) : Gold plated contacts Part Number CL No. Number of Contacts Weight RoHS Part Number CL No. Number of Contacts A Weight RoHS RM15WTRZA-2P() 109-1651-0- 2 21 22g RM15WTRZA-2S() 109-1657-6- 2 21.75 24g RM15WTRZA-3P() 109-1652-2- 3 22.1 24g RM15WTRZA-3S() 109-1658-9- 3 22.1 RM15WTRZA-4P() 109-1653-5- 4 21 23g RM15WTRZA-4S() 109-1659-1- 4 21.75 24g RM15WTRZA-8P() 109-1654-8- 8 20.65 22g RM15WTRZA-8S() 109-1660-0- 8 21.6 24g RM15WTRZA-10P() 109-1655-0- 10 20.65 23g RM15WTRZA-10S() 109-1661-3- 10 21.6 24g RM15WTRZA-12P() 109-1656-3- 12 20.65 23g RM15WTRZA-12S() 109-1662-6- 12 21.6 24g Notes : Recommended nut tightening torque: 3N*m 6 A YES 26g YES The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. BPlug -- Disassembly / Assembly Clamp Bushing Tightening collar Insulator body (P) Contacts 3 min Screw Washer Cable jacket Conductors Wires A Cable B Coupling Back shell Strain relief clamp Cable Back shell Part Name Tightening ring RM15WTPZA- RM15WTPZ- RM15WTLP- Table 1 Number of Contacts 3 2,4,8,10,12 3 2,4,8,10,12 10,12 A B 6mm 3mm 6mm 3mm 3mm 21mm 21mm 12mm 12mm 25mm Set screw(2) Disassembly 1. 1 Fix the plug in the assembly fixture (RM15TP-T01 (CL150-0098-0)), then remove the insulator body (P) and the back shell. Right-angle plugs have set screws in the tightening ring at 2 locations. Loosen the set screws before removing the back shell. 2 Remove the 2 screws of the strain relief clamp, and then remove the clamp from the tightening collar. Wiring 1 Assure that the cable outer diameter will fit the strain relief clamp, and is prepared as recommended in Table 1. It is recommended that the exposed conductors be pre-soldered, to assure easier insertion in the soldering cup. 2. 2 Pass the parts over the cable in the order of: tightening collar, washer, bushing, back shell, and coupling. Refer to the drawings (above) for assembly orientation of all components. 3 Solder the wires to the contacts of the insulator body (P). Use of heat-shrink tubing or another insulating media between the soldered contacts is suggested. Connector Assembly Straight Plugs 1 Place the completely wired insulator body (P) in the assembly fixture secured in a vise. Insert in the coupling, then back shell. The back shell should be tightened to a torque of 3 N*m. Right-angle Plugs 3. 1 Place the completely wired insulator body (P) in an assembly fixture secured by a vise. Insert in the coupling, then back shell (with tightening ring). When attaching the back shell, orient the cable in the desired direction and fasten the tightening ring to the insulator body (P) with a torque of 3 N*m. After this, tighten and fix the 2 sets crews with a torque of 0.2 to 0.3 N*m. Additional assembly recommendations: In applications where continuous extremely high vibrations may be encountered it is recommended that a thread locking compound be applied to male threads prior to assembly (Loctite 271 manufactured by Henkel Japan K.K. or equivalent) Waterproof verification - plug assembly 4. Apply air pressure of 17.6 kPa for 30 seconds from the mating side of the plug assembly. There shall not be any air leakage from inside the connector when submerged in the water tank. Precautions 5. 1 Follow the correct assembly sequence, cable preparation and tightening torques. 2 Assure that the applicable cable outer surfaces are free of scratches, oil, grease or any other contamination. 3 Do not use excessive forces or improper tools when assembling or mounting the connectors. 8 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. BReceptacle - recommended panel cut-outs Rear mounting, front nut Square flange, screw mounting 20.60.05 +0.1 0 O24 +0.1 0 O7.6 +0.1 0 O19.65 +0.05 0 O21 20.60.05 .1 +0 0 O17 4-M30.5 O19.2 +0.1 0 Front mounting, rear nut 1.40.05 Panel thickness: 0.5 to 2 mm Panel thickness: 0.5 to 2.5 mm For RM15WTRZ receptacles For RM15WTRZA receptacles Panel thickness: 2.5 to 4 mm For RM15WTRZB receptacles Notes : 1. When attaching the receptacle to the panel, be certain to check that the gasket is in place in the groove. Do not pinch the gasket. Notes : 2. The view of the above diagrams is from the receptacle mating side. Notes : 3. The symbol in the above diagrams indicates the coupling guide position of the receptacles. BContact Position Arrangement and Specifications Shell size : 15 Contact configuration Number of contacts 2 3 4 8 10 12 Withstanding voltage 1800V AC / 1 minute 2000V AC / 1 minute 1500V AC / 1 minute 1500V AC / 1 minute 1000V AC / 1 minute 1000V AC / 1 minute Current rating 10A 10A 10A 5A 5A 5A Insulation resistance 1000Mo min. 1000Mo min. 1000Mo min. 1000Mo min. 1000Mo min. 1000Mo min. Contact resistance 2mo max. 2mo max. 2mo max. 4mo max. 4mo max. 4mo max. Solder pot inner diameter 1.7mm 2.8mm 1.7mm 1.1mm 1.1mm 1.1mm Notes : 1. The contact configuration as viewed from the wiring side. Notes : 2. The symbol in the above diagrams indicates the coupling guide position of the receptacles. Notes : 3. Withstanding voltages indicate test voltage values. BPrecautions 1. Switch off the power of the circuit before disconnecting or plugging- in the connectors. 2. Use a connectors with socket contacts at the power side of the circuit. 3. Make sure that the coupling is in completely cocked position. 4. Use correct plug / receptacle to assure dust and water protection. 9 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Product Specifications (RM21WT to RM31WT size products) 600V AC, 840V DC (40 pos.) Voltage rating 500V AC, 700V DC (15, 31, 55 pos.) 350V AC, 490V DC (20 pos.) Rating Current rating 5A Operating temperature range (Note 1) -25c to +85c Storage temperature range (Note 2) -25c to +85c Characteristic Specification 1. Contact resistance 2. Insulation resistance Conditions 4 m o max. 1000 M o min 1A DC 500V DC 1800V AC/one minute (4 pos.) 1500V AC/one minute (15, 31, 55 pos.) 1000V AC/one minute (20 pos.) Frequency: 10 to 55Hz, single amplitude of 0.75mm,for 3 hours in 3 axis. Acceleration of 490m/s 2 , 11ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. 3. Withstanding voltage No flashover or insulation breakdown. 4. Vibration No electrical discontinuity for 10s max. 5. Shock No electrical discontinuity for 10s max. 6. Durability 8 m o max. (insertion/withdrawal) 2000 cycles 7. Temperature cycle Insulation resistance: 100 M o min. 8. Humidity Insulation resistance: 100 M o min. (Dray state) Temperature : -55c Room temperature +85c Room temperature Time : 30 10 to 15 30 10 to 15 (Minutes) 5 cycles 96 hours at temperature 0f 40c and humidity 0f 90% to 95%. Complete dust protection. No water penetration when submerged for 48 hours at the depth of 1.8 meter. 9. Water / dust protection 0When mated with corresponding connector. Note 1: Includes temperature rise caused by the current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating temperature range and humidity range Note 2: covers non-conducting condition of installed connectors in storage, shipment or during transportation. Materials Item Material Finish Remarks Body Brass Chrome plated or nickel plated ------------------- Insulator Diallyl phthalate Color: Black UL94V-0 Contacts Brass, copper alloy Silver plated or gold plated ------------------- Gasket Chloroprene rubber or SIR Color: black ------------------- Note: Do not mix different contact plating. Ordering Information * * - 2 P (* *) RM 21 W T P* 1 2 1 4 5 6 1 Series name : RM-W 5 Number of Contacts 2 Shell size 6 Contact type 3 Lock type T : Screw Lock 4 Connector type 10 3 7 P : Male contact S : Female contact 7 Plating P : Plug (71) : Silver plated R : Receptacle (72) : Gold plated RM 21 W T P - CP (10) (* *) 8 8 CP: Strain relief 9 () with 9 : External cable clamp () without : Internal cable clamp 4~18 : Cable size The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Plugs - straight, long back shell RM21WTPS-15S(71) Wrench opening dimension D E F 8 9 7 10 1 OB OA Y 11 13 15 6 14 5 12 2 4 3 Z C (shown one example) Part Number RM21WTPS-15S(71) RM24WTPB-31S(71) RM24WTPB-31P(71) CL No. Number of Contacts 15 109-1860-0-71 31 109-1852-1-71 31 109-1855-0-71 OA 21 24.3 24.3 OB 32 36 36 C 49 54 54 D 23 26 26 E TM252 TM292 TM292 F Weight Remarks RoHS M200.75 104.5 Silver plated M240.75 144.6 YES only M240.75 140.0 Applicable Strain reliefs External cable clamp + internal, self-tightening RM24WTP-CP14(71) OA OB E Wrench opening dimension D C (shown one example) Part Number CL No. OA OB C D E Weight Remarks 04 JR16WCC-4(72) 23 17.5 21 M200.75 17.5g 114-2052-6-72 06 JR16WCC-6(72) 23 17.5 21 M200.75 17.5g 114-2053-9-72 08 JR16WCC-8(72) 23 17.5 21 M200.75 17.5g 114-2054-1-72 For RM21WT 10 JR16WCC-10(72) 23 17.5 21 M200.75 17.5g 114-2055-4-72 11 JR16WCC-11(72) 23 17.5 21 M200.75 17.5g 114-2154-6-72 12 JR16WCC-12(72) 23 17.5 21 M200.75 17.5g 114-2056-7-72 14 109-1851-9-71 RM24WTP-CP14(71) 29 17.5 26 M240.75 17.5g For RM24WT Notes : 1. Cable jacket diameter:Use A 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.3 to 0.4 N*m. HRS recommended tool : PB205/1.27(CL 150-0066-3) RoHS YES Internal, self tightening E RM21WTP-CP(8)(71) OB OA Set screw D C (shown one example) Part Number CL No. OA OB C D E Weight Remarks 23 38 7.5 M200.75 RM21WTP-CP(8)(71) 109-1405-3-71 08 22.5 For RM21WT 23 38 7.5 M200.75 RM21WTP-CP(10)(71) 109-1406-6-71 10 22.0 23 38 7.5 M200.75 RM21WTP-CP(12)(71) 109-1407-9-71 12 21.5 27 38.5 8 M240.75 RM24WTP-CP(10)(71) 109-1493-0-71 10 28.5 27 38.5 8 M240.75 RM24WTP-CP(12)(71) 109-1494-3-71 12 28.5 For RM24WT 27 38.5 8 M240.75 RM24WTP-CP(14)(71) 109-1495-6-71 14 28.0 RM24WTP-CP(16)(71) 109-1496-9-71 16 26.5 27 38.5 8 M240.75 Notes : 1. Cable jacket diameter:Use A 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.2 to 0.3 N*m. Notes : 3. When using the self-tightening strain relief verify the cable pull force requirements. RoHS YES 11 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Plugs - Straight, short back shell D RM21WTP-15S(71) Set screw E 8 9 7 10 1 OB OA Y 13 11 14 15 6 12 5 2 3 Z 4 C (shown one example) Part Number CL No. Number of Contacts 15 RM21WTP-15S(71) 109-1401-2-71 20 RM21WTP-20S(71) 109-1402-5-71 15 RM21WTP-15P(71) 109-1403-8-71 20 RM21WTP-20P(71) 109-1404-0-71 31 RM24WTP-31S(71) 109-1491-5-71 31 RM24WTP-31P(71) 109-1492-8-71 40 RM31WTP-40S(71) 109-1571-2-71 55 RM31WTP-55S(71) 109-1572-5-71 40 RM31WTP-40P(71) 109-1573-8-71 55 RM31WTP-55P(71) 109-1574-0-71 Notes : Recommended set screw tightening torque : 0.2 to 0.3 N*m. OA 21 21 21 21 24.3 24.3 30.8 30.8 30.8 30.8 OB 32 32 32 32 36 36 42 42 42 42 C 37.5 37.5 37.5 37.5 44 44 52 52 52 52 E TM252 TM252 TM252 TM252 TM292 TM292 TM352 TM352 TM352 TM352 F M200.75 M200.75 M200.75 M200.75 M240.75 M240.75 M280.75 M280.75 M280.75 M280.75 Weight 88.5 88.5 85 85 128 123 152 157 152 150 Applicable Strain reliefs External cable clamp + internal, self-tightening E OA OB RM24WTP-CP14(71) Wrench opening dimension D C (shown one example) Part Number CL No. OA OB C D E RoHS 10 109-1478-7-71 RM21WTP-CP10(71) 25 17 21 M200.75 12 109-1477-4-71 RM21WTP-CP12(71) 25 17 21 M200.75 YES 14 109-1851-9-71 RM24WTP-CP14(71) 29 17.5 26 M240.75 Notes : 1. Cable jacket diameter:Use A 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.3 to 0.4 N*m. HRS recommended tool : PB205/1.27(CL 150-0066-3) Internal, self tightening E RM21WTP-CP(8)(71) OB OA Set screw D C (shown one example) Part Number CL No. OA OB C D E Weight RoHS 08 RM21WTP-CP(8)(71) 23 38 7.5 M200.75 22.5 109-1405-3-71 10 RM21WTP-CP(10)(71) 23 38 7.5 M200.75 22 109-1406-6-71 12 RM21WTP-CP(12)(71) 23 38 7.5 M200.75 21.5 109-1407-9-71 10 RM24WTP-CP(10)(71) 27 38.5 8 M240.75 28.5 109-1493-0-71 12 RM24WTP-CP(12)(71) 27 38.5 8 M240.75 28.5 109-1494-3-71 14 RM24WTP-CP(14)(71) 27 38.5 8 M240.75 28.5 109-1495-6-71 YES 16 RM24WTP-CP(16)(71) 27 38.5 8 M240.75 28.5 109-1496-9-71 10 RM31WTP-CP(10)(71) 31 42 12 M280.75 46 109-1575-3-71 12 RM31WTP-CP(12)(71) 31 42 12 M280.75 46 109-1576-6-71 14 RM31WTP-CP(14)(71) 31 42 12 M280.75 45 109-1579-4-71 16 RM31WTP-CP(16)(71) 31 42 12 M280.75 43.5 109-1577-9-71 18 RM31WTP-CP(18)(71) 31 42 12 M280.75 42 109-1578-1-71 Notes : 1. Cable jacket diameter:Use A 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.2 to 0.3 N*m. Notes : 3. When using the self-tightening strain relief verify the cable pull force requirements. 12 Remarks Silver plated only RoHS YES The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Receptacles Front panel mount Z 2 10 14 15 7 9 Y Y 7 9 6 14 10 13 5 15 12 1 1 11 13 OA 5 12 11 4 2 4 6 Z 3 3 RM21WTR-15P(71) 8 8 F C D B E (shown one example) Part Number CL No. Number of Contacts OA B C D E E Weight RM21WTR-15P(71) 109-1445-8-71 15 31 21 6.5 2 23.5 TM252 28 RM21WTR-15S(71) 109-1447-3-71 15 31 21 6.5 2 23.5 TM252 31.5 RM21WTR-20P(71) 109-1446-0-71 20 31 21 6.5 2 23.5 TM252 31.5 RM21WTR-20S(71) 109-1448-6-71 20 31 21 6.5 2 23.5 TM252 31.5 RM24WTR-31P(71) 109-1483-7-71 31 35 21 6.5 2.5 28 TM292 41.5 RM24WTR-31S(71) 109-1484-0-71 31 35 21 6.5 2.5 28 TM292 42 RM31WTR-40P(71) 109-1525-5-71 40 41 21 6.5 2.5 34 TM352 50 RM31WTR-40S(71) 109-1527-0-71 40 41 21 6.5 2.5 34 TM352 52 RM31WTR-55P(71) 109-1526-8-71 55 41 21 6.5 2.5 34 TM352 53.5 RM31WTR-55S(71) 109-1528-3-71 55 41 21 6.5 2.5 34 TM352 54 32 24 4- Remarks Silver plated only RoHS YES Notes : Recommended nut tightening torque : 3 N*m Waterproof (single body) RM21WTRK-20P(71) .6 4 5 14 20 13 12 11 2 1 19 9 7 8 8 7 6 15 17 16 15 16 10 18 19 6 20 14 18 1 5 10 11 13 12 9 17 2 4 O23.7 3 TM252 3 32 24 20.62 6 O3 TM252 (shown one example) Part Number CL No. Number of Contacts Remarks RoHS RM21WTRK-20P(71) 109-1466-8-71 20 Gold plated only YES Notes : 1. Screw size : M3 2. Recommended nut tightening torque : 0.3 to 0.35 N*m 3. Use a 1.9 to 2.0 mm dia.thick O-ring for the waterproof gasket that is used in the connector mounting portion. 13 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. BReceptacle - recommended panel cut-out Front mounting, rear nut Square flange, screw mounting 240.05 OA O24 +0.1 0 O280.1 C 240.05 R 1.40.05 4-M30.5 B Panel thickness: 0.5 to 2 mm Panel thickness: 2.5 to 4 mm **WTR receptacles For RM* For RM21WTRK receptacles Part Number OA B RC For RM21WTR 22.1 13.3 0.8 For RM24WTR 26.1 15.1 0.8 For RM31WTR 32.1 18.3 0.85 Notes : Tolelance is +0.1/0. Notes : 1. When attaching the receptacle to the panel, be certain to check that the gasket is in place in the groove. Do not pinch the gasket. Notes : 2. The view of the above diagrams is from the receptacle mating side. Notes : 3. The symbol in the above diagrams indicates the coupling guide position of the receptacles. BContact Position Arrangement and Specifications Shell size : 21 10 Contact configuration 9 17 8 16 7 15 6 Number of contacts Withstanding voltage 15 Shell size : 24 18 19 1 11 2 12 3 20 14 1 12 11 24 13 14 13 4 5 20 23 10 22 9 30 Shell size : 31 2 25 15 17 3 16 26 27 17 4 18 5 20 19 7 6 29 21 28 8 37 14 28 13 4 22 34 5 23 35 29 36 27 26 11 10 12 6 24 7 25 8 9 18 34 36 35 19 1 20 37 38 48 40 55 1800V AC / 1 minute 1500V AC / 1 minute Current rating 5A 5A 5A 5A 5A Insulation resistance 1000Mo min. 1000Mo min. 1000Mo min. 1000Mo min. 1000Mo min. Contact resistance 4mo max. 4mo max. 4mo max. 4mo max. 4mo max. Solder pot inner diameter 1.1mm 1.1mm 1.1mm 1.1mm 1.1mm Notes : 1. The contact configuration as viewed from the wiring side. Notes : 2. The symbol in the above diagrams indicates the coupling guide position of the receptacles. Notes : 3. Withstanding voltages indicate test voltage values. BPrecautions 1. Switch off the power of the circuit before disconnecting or plugging- in the connectors. 2. Use a connectors with socket contacts at the power side of the circuit. 3. Make sure that the coupling is in completely cocked position. 4. Use correct plug / receptacle to assure dust and water protection. 14 40 38 15 31 1500V AC / 1 minute 1000V AC / 1 minute 1500V AC / 1 minute 33 39 17 2 3 21 22 15 4 49 39 47 23 50 33 54 55 5 14 46 40 24 32 51 53 6 13 41 52 45 44 42 25 31 26 30 43 27 29 12 7 28 11 8 9 10 16 3 21 31 30 2 20 32 16 31 1 19 18 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.