CAT.8100D
4
5
5
6.3
19
26
32
52
5
5
6.3
24
30
40
4
5
6.3
6.3
16
26
35
44
4
5
6.3
6.3
11
20
33
42
4
5
6.3
13
22
36
4
4
4
4
4
4
4
5
6.3
0.9
2.2
2.8
3.3
5.4
9.6
12
16
26
U
1
Z
2
T
3
1
4
C
5
1
6
0
7
0
8
M
9
C
10
L
11
1
12
G
13
B
14
Configuration
Taping code
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
Voltage mark for 6.3V is 6V .
φD
A
B
C
E
1.8
4.3
4.3
1.0
2.1
5.3
5.3
1.3
4
(mm)
5
2.4
6.6
6.6
2.2
6.3
105˚C Marking
Voltage
Capacitance
Lot No.
A2P
10
16V
Plastic platform
0.3 MAX.
4.5 +0.1
0.2
φD±0.5
B±0.2
C±0.2
0.5 MAX.
A±0.3 A±0.3
E
0.5 to 0.8
Positive
Negative
ZT series
4.5mmL Chip Type, Wide Temperature Range
Chip type with 4.5mm height, operating over wide temperature
range of –40 to +105
°C
.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Chip Type Type numbering system (Example : 16V 10
µ
F)
Specifications
Category
Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Shelf Life
Marking
Performance CharacteristicsItem
40 to +105°C
6.3 to 50V
0.1 to 100µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Black print on the case top.
Measurement frequency : 120Hz at 20°C
Measurement frequency : 120Hz
The specifications listed at right shall be
met when the capacitors are restored to
20°C after the rated voltage is applied for
1000 hours at 105°C.
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
Resistance to soldering
heat
The capacitors are kept on a hot plate for 30 seconds, which
is maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Rated voltage (V)
tan δ (MAX.)
6.3
0.38
10
0.32
16
0.20
25
0.16
35
0.14
50
0.14
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
6.3
6
10
10
5
10
16
3
6
25
3
6
35
3
4
50
3
4
Capacitance
change
Leakage current
tan δ
Within ±25% of the initial capacitance value (16V or less)
Within ±20% of the initial capacitance value (25V or more)
300% or less than initial specified value
Less than or equal to the initial specified value
Capacitance change
Leakage current
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
ZT
Dimensions
    0.1
    0.22
    0.33
    0.47
    1
    2.2
    3.3
    4.7
  10
  22
  33
  47
100
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
6.3
0J
10
1A
16
1C
25
1E
35
1V
50
1H
V
Code
Rated ripple current (mArms) at 105°C 120Hz
Cap. (µF)
Rated
ripple
ALUMINUM  ELECTROLYTIC  CAPACITORS
Case size
φD (mm)
ZG
Smaller
WT
Smaller
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UX(p.154), UJ(p.160) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
Frequency coefficient of rated ripple current
Coefficient
Frequency 50 Hz 120 Hz 300 Hz 1 kHz
10 kHz or more
0.70 1.00 1.17 1.36 1.50  
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Nichicon:
UZT1C100MCR1GB