ALUMINUM ELECTROLYTIC CAPACITORS ZT 4.5mmL Chip Type, Wide Temperature Range series WT Chip type with 4.5mm height, operating over wide temperature range of - 40 to +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). Smaller ZT Smaller ZG Specifications Item Performance Characteristics Category Temperature Range -40 to +105C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 100F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (A) , whichever is greater. Measurement frequency : 120Hz at 20C 6.3 0.38 Rated voltage (V) tan (MAX.) Tangent of loss angle (tan ) 10 0.32 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Stability at Low Temperature 6.3 6 10 Rated voltage (V) Z- 25C / Z+20C Impedance ratio ZT / Z20 (MAX.) Z- 40C / Z+20C 10 5 10 Resistance to soldering heat Marking Type numbering system (Example : 16V 10F) 1 Positive Voltage mark for 6.3V is 6V . E D0.5 4.5 +0.1 -0.2 3 4 5 6 7 8 9 10 11 12 13 14 Taping code A0.3 A 0.3 C0.2 B0.2 Plastic platform 0.3 MAX. Voltage 2 U Z T 1 C 1 0 0 MC L 1 GB 0.5 MAX. 105C Marking A2P 10 16V 50 3 4 Within 25% of the initial capacitance value (16V or less) Within 20% of the initial capacitance value (25V or more) tan 300% or less than initial specified value Leakage current Less than or equal to the initial specified value Chip Type Lot No. 35 3 4 After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Capacitance change Within 10% of the initial capacitance value is maintained at 250C. The capacitors shall meet the Less than or equal to the initial specified value tan characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20C. Black print on the case top. Shelf Life Capacitance 25 3 6 Capacitance change The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 105C. Endurance 16 3 6 D A B C E 4 1.8 4.3 4.3 1.0 (mm) 5 6.3 2.1 2.4 5.3 6.6 5.3 6.6 1.3 2.2 Configuration Capacitance tolerance (20%) Rated capacitance (10F) Rated voltage (16V) Series name Negative 0.5 to 0.8 Type Dimensions 6.3 0J V Cap. (F) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 4 5 5 6.3 10 1A 19 26 32 52 5 5 6.3 16 1C 24 30 40 4 5 6.3 6.3 25 1E 16 26 35 44 4 5 6.3 6.3 35 1V 11 20 33 42 4 5 6.3 50 1H 13 22 36 4 4 4 4 4 4 4 5 6.3 Case size D (mm) 0.9 2.2 2.8 3.3 5.4 9.6 12 16 26 Rated ripple Rated ripple current (mArms) at 105C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UX(p.154), UJ(p.160) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100D Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Nichicon: UZT1C100MCR1GB