LT3083 Adjustable 3A Single Resistor Low Dropout Regulator DESCRIPTION FEATURES n n n n n n n n n n n n n n Outputs May be Paralleled for Higher Current and Heat Spreading Output Current: 3A Single Resistor Programs Output Voltage 50A Set Pin Current: 1% Initial Accuracy Output Adjustable to 0V Low Output Noise: 40VRMS (10Hz to 100kHz) Wide Input Voltage Range: 1.2V to 23V (DD-Pak and TO-220 Packages) Low Dropout Voltage: 310mV <1mV Load Regulation <0.001%/V Line Regulation Minimum Load Current: 1mA Stable with Minimum 10F Ceramic Capacitor Current Limit with Foldback and Overtemperature Protection Available in 16-Lead TSSOP, 12-Lead 4mm x 4mm DFN, 5-Lead TO-220 and 5-Lead Surface Mount DD-PAK Packages APPLICATIONS n n n n n High Current All Surface Mount Supply High Efficiency Linear Regulator Post Regulator for Switching Supplies Low Parts Count Variable Voltage Supply Low Output Voltage Power Supplies The LT(R)3083 is a 3A low dropout linear regulator that can be paralleled to increase output current or spread heat on surface mounted boards. Architected as a precision current source and voltage follower, this new regulator finds use in many applications requiring high current, adjustability to zero, and no heat sink. The device also brings out the collector of the pass transistor to allow low dropout operation--down to 310mV--when used with multiple supplies. A key feature of the LT3083 is the capability to supply a wide output voltage range. By using a reference current through a single resistor, the output voltage is programmed to any level between zero and 23V (DD-PAK and TO-220 packages). The LT3083 is stable with 10F of capacitance on the output, and the IC is stable with small ceramic capacitors that do not require additional ESR as is common with other regulators. Internal protection circuitry includes current limiting and thermal limiting. The LT3083 is offered in the 16-lead TSSOP (with an exposed pad for better thermal characteristics), 12-lead 4mm x 4mm DFN (also with an exposed pad), 5-lead TO-220, and 5-lead surface mount DD-PAK packages. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Set Pin Current Distribution 1.5V to 0.9V at 3A Supply (Using 3.3V VCONTROL) VCONTROL 3.3V N = 1052 4.7F VCONTROL VIN 1.5V IN 10F LT3083 OUT 10F SET 3083 TA01a RSET 18.2k 1% 0.1F *RMIN 909 VOUT = 0.9V IMAX = 3A *OPTIONAL FOR MINIMUM 1mA LOAD REQUIREMENT 49 49.5 50 50.5 SET PIN CURRENT DISTRIBUTION (A) 51 3083 TA01b 3083fa 1 LT3083 ABSOLUTE MAXIMUM RATINGS (Note 1) All Voltages Relative to VOUT CONTROL Pin Voltage..............................................28V IN Pin Voltage (T5, Q Packages).....................18V, -0.3V No Overload or Short-Circuit......................23V, -0.3V IN Pin Voltage (DF, FE Packages)......................8V, -0.3V No Overload or Short-Circuit......................14V, -0.3V SET Pin Current (Note 7)......................................25mA SET Pin Voltage (Relative to OUT)........................... 10V Output Short-Circuit Duration........................... Indefinite Operating Junction Temperature Range (Notes 2, 10) E-, I-grades......................................... -40C to 125C MP-grade............................................ -55C to 125C Storage Temperature Range................... -65C to 150C Lead Temperature (Soldering, 10 sec) T, Q, FE Packages Only...................................... 300C PIN CONFIGURATION TOP VIEW OUT 1 16 OUT OUT 2 15 IN OUT 3 14 IN 10 IN OUT 4 9 IN OUT 5 TOP VIEW OUT 1 12 IN OUT 2 11 IN OUT 3 OUT 4 OUT 5 8 VCONTROL OUT 6 SET 6 7 VCONTROL 11 VCONTROL SET 7 10 VCONTROL OUT 8 9 13 OUT DF PACKAGE 12-LEAD (4mm x 4mm) PLASTIC DFN 17 OUT 13 IN 12 IN OUT FE PACKAGE 16-LEAD PLASTIC TSSOP TJMAX = 125C, JA = 37C/W, JC = 8C/W EXPOSED PAD (PIN 13) IS OUT, MUST BE SOLDERED TO PCB TJMAX = 125C, JA = 25C/W, JC = 8C/W EXPOSED PAD (PIN 17) IS OUT, MUST BE SOLDERED TO PCB FRONT VIEW TAB IS OUT FRONT VIEW 5 IN 5 4 VCONTROL 4 VCONTROL 3 OUT 3 OUT 2 SET 2 SET NC 1 NC 1 TAB IS OUT IN Q PACKAGE 5-LEAD PLASTIC DD-PAK T PACKAGE 5-LEAD PLASTIC TO-220 TJMAX = 125C, JA = 15C/W, JC = 3C/W TJMAX = 125C, JA = 40C/W, JC = 3C/W ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3083EDF#PBF LT3083EDF#TRPBF 3083 12-Lead (4mm x 4mm) Plastic DFN -40C to 125C LT3083EFE#PBF LT3083EFE#TRPBF 3083FE 16-Lead Plastic TSSOP -40C to 125C LT3083EQ#PBF LT3083EQ#TRPBF LT3083Q 5-Lead Plastic DD-PAK -40C to 125C LT3083ET#PBF LT3083ET#TRPBF LT3083T 5-Lead Plastic TO-220 -40C to 125C LT3083IDF#PBF LT3083IDF#TRPBF 3083 12-Lead (4mm x 4mm) Plastic DFN -40C to 125C LT3083IFE#PBF LT3083IFE#TRPBF 3083FE 16-Lead Plastic TSSOP -40C to 125C 3083fa 2 LT3083 ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3083IQ#PBF LT3083IQ#TRPBF LT3083Q 5-Lead Plastic DD-PAK -40C to 125C LT3083IT#PBF LT3083IT#TRPBF LT3083T 5-Lead Plastic TO-220 -40C to 125C LT3083MPDF#PBF LT3083MPDF#TRPBF 3083 12-Lead (4mm x 4mm) Plastic DFN -55C to 125C LT3083MPFE#PBF LT3083MPFE#TRPBF 3083FE 16-Lead Plastic TSSOP -55C to 125C LT3083MPQ#PBF LT3083MPQ#TRPBF LT3083Q 5-Lead Plastic DD-PAK -55C to 125C LT3083MPT#PBF LT3083MPT#TRPBF LT3083T 5-Lead Plastic TO-220 -55C to 125C LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3083EDF LT3083EDF#TR 3083 12-Lead (4mm x 4mm) Plastic DFN -40C to 125C LT3083EFE LT3083EFE#TR 3083FE 16-Lead Plastic TSSOP -40C to 125C LT3083EQ LT3083EQ#TR LT3083Q 5-Lead Plastic DD-PAK -40C to 125C LT3083ET LT3083ET#TR LT3083T 5-Lead Plastic TO-220 -40C to 125C LT3083IDF LT3083IDF#TR 3083 12-Lead (4mm x 4mm) Plastic DFN -40C to 125C LT3083IFE LT3083IFE#TR 3083FE 16-Lead Plastic TSSOP -40C to 125C LT3083IQ LT3083IQ#TR LT3083Q 5-Lead Plastic DD-PAK -40C to 125C LT3083IT LT3083IT#TR LT3083T 5-Lead Plastic TO-220 -40C to 125C LT3083MPDF LT3083MPDF#TR 3083 12-Lead (4mm x 4mm) Plastic DFN -55C to 125C LT3083MPFE LT3083MPFE#TR 3083FE 16-Lead Plastic TSSOP -55C to 125C LT3083MPQ LT3083MPQ#TR LT3083Q 5-Lead Plastic DD-PAK -55C to 125C LT3083MPT LT3083MPT#TR LT3083T 5-Lead Plastic TO-220 -55C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C (Note 2). PARAMETER SET Pin Current Output Offset Voltage (VOUT - VSET) VIN = 1V, VCONTROL = 2V, ILOAD = 1mA CONDITIONS ISET VOS VIN = 1V, VCONTROL = 2V, ILOAD = 1mA, TJ = 25C VIN 1V, VCONTROL 2V, 5mA ILOAD 3A (Note 9) MIN TYP MAX UNITS l 49.5 49 50 50 50.5 51 A A l -3 -4 0 0 3 4 mV mV l -4 -6 0 0 4 6 mV mV DF, FE Packages T, Q Packages ISET VOS ILOAD = 1mA to 3A ILOAD = 5mA to 3A (Note 8) l -10 -0.4 -1 nA mV ISET VOS ILOAD = 1mA to 3A ILOAD = 5mA to 3A (Note 8) l -10 -0.7 -4 nA mV Line Regulation (DF, FE Packages) ISET VOS VIN = 1V to 14V, VCONTROL = 2V to 25V, ILOAD = 1mA VIN = 1V to 14V, VCONTROL = 2V to 25V, ILOAD = 1mA 0.1 0.002 0.01 nA/V mV/V Line Regulation (T, Q Packages) ISET VOS VIN = 1V to 23V, VCONTROL = 2V to 25V, ILOAD = 1mA VIN = 1V to 23V, VCONTROL = 2V to 25V, ILOAD = 1mA 0.1 0.002 0.01 nA/V mV/V 500 1 A mA Load Regulation (DF, FE Packages) Load Regulation (T, Q Packages) Minimum Load Current (Notes 3, 9) VIN = 1V, VCONTROL = 2V VIN = 14V (DF/FE) or 23V (T/Q), VCONTROL = 25V l l 350 3083fa 3 LT3083 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C (Note 2). PARAMETER CONDITIONS VCONTROL Dropout Voltage (Note 4) ILOAD = 100mA ILOAD = 1A ILOAD = 3A TYP MAX UNITS l l 1.2 1.22 1.25 1.55 1.6 V V V ILOAD = 100mA l 10 25 mV ILOAD = 1A, Q, T Packages ILOAD = 1A, DF, FE Packages l l 120 90 190 160 mV mV ILOAD = 3A, Q, T Packages ILOAD = 3A, DF, FE Packages l l 310 240 510 420 mV mV VCONTROL Pin Current (Note 5) ILOAD = 100mA ILOAD = 1A ILOAD = 3A l l l 5.5 18 40 10 35 80 mA mA mA Current Limit VIN = 5V, VCONTROL = 5V, VSET = 0V, VOUT = -0.1V l Error Amplifier RMS Output Noise (Note 6) ILOAD = 500mA, 10Hz f 100kHz, COUT = 10F, CSET = 0.1F VIN Dropout Voltage (Note 4) MIN 3 3.7 A 40 VRMS Reference Current RMS Output Noise (Note 6) 10Hz f 100kHz 1 nARMS Ripple Rejection VRIPPLE = 0.5VP-P, IL = 0.1A, CSET = 0.1F, COUT = 10F f = 120Hz f = 10kHz f = 1MHz 85 75 20 dB dB dB Thermal Regulation, ISET 10ms Pulse Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Unless otherwise specified, all voltages are with respect to VOUT. The LT3083 is tested and specified under pulse load conditions such that TJ TA. The LT3083E is 100% tested at TA = 25C. Performance of the LT3083E over the full -40C to 125C operating junction temperature range is assured by design, characterization, and correlation with statistical process controls. The LT3083I regulators are guaranteed over the full -40C to 125C operating junction temperature range. The LT3083MP is 100% tested and guaranteed over the -55C to 125C operating junction temperature range. Note 3: Minimum load current is equivalent to the quiescent current of the part. Since all quiescent and drive current is delivered to the output of the part, the minimum load current is the minimum current required to maintain regulation. Note 4: For the LT3083, dropout is caused by either minimum control voltage (VCONTROL) or minimum input voltage (VIN). Both parameters are specified with respect to the output voltage. The specifications represent the minimum input-to-output differential voltage required to maintain regulation. 0.003 %/W Note 5: The VCONTROL pin current is the drive current required for the output transistor. This current will track output current with roughly a 1:60 ratio. The minimum value is equal to the quiescent current of the device. Note 6: Output noise is lowered by adding a small capacitor across the voltage setting resistor. Adding this capacitor bypasses the voltage setting resistor shot noise and reference current noise; output noise is then equal to error amplifier noise (see the Applications Information section). Note 7: The SET pin is clamped to the output with diodes through 1k resistors. These resistors and diodes will only carry current under transient overloads. Note 8: Load regulation is Kelvin sensed at the package. Note 9: Current limit includes foldback protection circuitry. Current limit decreases at higher input-to-output differential voltages. Note 10: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed the maximum operating junction temperature when overtemperature protection is active. Overtemperature protection (thermal limit) is typically active at junction temperatures of 165C. Continuous operation above the specified maximum operating junction temperature may impair device reliability. 3083fa 4 LT3083 TYPICAL PERFORMANCE CHARACTERISTICS SET Pin Current TA = 25C, unless otherwise noted. Set Pin Current Distribution 50.5 1.0 N = 1052 50.4 0.6 OFFSET VOLTAGE (mV) SET PIN CURRENT (A) 50.2 50.1 50.0 49.9 49.8 0.2 0 -0.2 -0.4 -0.6 49.6 -0.8 49.5 -50 -25 0 49.5 50 50.5 SET PIN CURRENT DISTRIBUTION (A) 49 25 50 75 100 125 150 TEMPERATURE (C) -1.0 -50 -25 51 Offset Voltage Distribution 1.00 Offset Voltage (VOUT - VSET) Offset Voltage (VOUT - VSET) 0.25 ILOAD = 5mA 0.75 0 0.50 -0.25 0.25 0 -0.25 -0.50 -0.75 -1 0 1 2 VOS DISTRIBUTION (mV) -1.00 3 10 15 20 5 INPUT-TO-OUTPUT VOLTAGE (V) 0 0 CHANGE IN REFERENCE CURRENT -50 -0.8 -100 -1.0 -150 -1.2 -200 -250 -1.4 ILOAD = 5mA TO 3A VIN = VCONTROL = VOUT + 2V -300 -1.6 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3083 G07 -1.00 -1.25 25 -1.75 0 0.5 1 1.5 2 LOAD CURRENT (A) 2.5 1.4 Dropout Voltage, T/Q Packages (Minimum IN Voltage) 400 VIN = VCONTROL 1.2 1.0 VIN,CONTROL - VOUT = 23V 0.8 0.6 VIN, CONTROL - VOUT = 1.5V 0.4 0.2 0 -50 -25 0 3 3083 G06 Minimum Load Current MINIMUM LOAD CURRENT (mA) 50 CHANGE IN REFERENCE CURRENT WITH LOAD (nA) 100 -0.4 -0.75 3083 G05 Load Regulation CHANGE IN OFFSET VOLTAGE (VOUT - VSET) TJ = 125C -1.50 3083 G04 0 TJ = 25C -0.50 MINIMUM VOLTAGE (VIN - VOUT) (mV) -2 25 50 75 100 125 150 TEMPERATURE (C) 3083 G03 OFFSET VOLTAGE (mV) OFFSET VOLTAGE (mV) N = 1052 -3 0 3083 G02 3083 G01 CHANGE IN OFFSET VOLTAGE WITH LOAD (mV) 0.4 49.7 -0.6 ILOAD = 5mA 0.8 50.3 -0.2 Offset Voltage (VOUT - VSET) 25 50 75 100 125 150 TEMPERATURE (C) 3083 G08 350 TJ = 125C 300 250 TJ = 25C 200 TJ = -50C 150 100 50 0 0 0.5 1 1.5 2 LOAD CURRENT (A) 2.5 3 3083 G09 3083fa 5 LT3083 TYPICAL PERFORMANCE CHARACTERISTICS Dropout Voltage, T/Q Packages (Minimum IN Voltage) Dropout Voltage, FE/DF Packages Dropout Voltage, FE/DF Packages (Minimum IN Voltage) 500 350 TJ = 125C 300 250 TJ = 25C 200 150 TJ = -50C 100 50 0 0.5 1 1.5 2 LOAD CURRENT (A) 2.5 450 400 ILOAD = 3A 350 300 250 ILOAD = 1.5A 200 150 ILOAD = 500mA 100 3 50 ILOAD = 100mA 0 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3083 G10 350 ILOAD = 3A 300 250 ILOAD = 1.5A 200 150 100 ILOAD = 500mA 50 ILOAD = 100mA 0 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3083 G12 1.6 1.4 TJ = -50C 1.2 1.0 MINIMUM VCONTROL PIN VOLTAGE (VCONTROL - VOUT) (V) MINIMUM VCONTROL PIN VOLTAGE (VCONTROL - VOUT) (V) 400 Dropout Voltage (Minimum VCONTROL Pin Voltage) 1.6 TJ = 25C TJ = 125C 0.8 0.6 0.4 0.2 0 0.5 1 1.5 2 LOAD CURRENT (A) 2.5 1.4 ILOAD = 3A 1.2 1.0 0.8 0.6 0.4 0.2 0 -50 -25 3 0 25 50 75 100 125 150 TEMPERATURE (C) 3083 G13 3083 G14 Current Limit Current Limit 5.0 4.0 4.5 3.5 4.0 TJ = 25C 3.0 3.5 CURRENT LIMIT (A) CURRENT LIMIT (A) 450 3083 G11 Dropout Voltage (Minimum VCONTROL Pin Voltage) 0 MINIMUM IN VOLTAGE (VIN - VOUT) (mV) 500 MINIMUM IN VOLTAGE (VIN - VOUT) (mV) MINIMUM VOLTAGE (VIN - VOUT) (mV) 400 0 TA = 25C, unless otherwise noted. 3.0 2.5 2.0 1.5 2.5 2.0 1.5 1.0 1.0 0.5 VIN = VCONTROL = 7V VOUT = 0V 0 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3083 G15 0.5 0 0 5 10 15 20 IN-TO-OUT DIFFERENTIAL (VIN - VOUT) (V) 3083 G16 3083fa 6 LT3083 TYPICAL PERFORMANCE CHARACTERISTICS 150 VIN = 2V 100 VCONTROL = 3V VOUT = 1V 50 CSET = 0.1F COUT = 22F CERAMIC 0 -50 LOAD CURRENT (A) Load Transient Response 250 LOAD CURRENT (A) OUTPUT VOLTAGE DEVIATION (mV) OUTPUT VOLTAGE DEVIATION (mV) Load Transient Response COUT = 10F CERAMIC -100 1.0 0.5 0 ILOAD = 100mA TO 1A 0 TA = 25C, unless otherwise noted. VIN = 2V VCONTROL = 3V VOUT = 1V CSET = 0.1F 150 50 COUT = 22F CERAMIC -50 -150 4 2 ILOAD = 500mA TO 3A 0 0 20 40 60 80 100 120 140 160 180 200 TIME (s) 20 40 60 80 100 120 140 160 180 200 TIME (s) 3083 G18 3083 G17 Line Transient Response Turn-On Response 2 3 1 10 0 0 -10 -20 0 RSET = 20k CSET = 0 RLOAD = 0.33 COUT = 10F CERAMIC 0.5 0 0 5 70 40 ILOAD = 3A 30 DEVICE IN CURRENT LIMIT 20 ILOAD = 1.5A 10 0 0 VCONTROL PIN CURRENT (mA) VCONTROL PIN CURRENT (mA) 70 50 3083 G22 RSET = 20k CSET = 0.1F RLOAD = 1 COUT = 10F CERAMIC 0 -0.5 10 15 20 25 30 35 40 45 50 TIME (s) 0 2 4 6 8 10 12 14 16 18 20 TIME (ms) Residual Output Voltage with Less Than Minimum Load 600 VCONTROL - VOUT = 2V VIN - VOUT = 1V 60 TJ = -50C 40 30 TJ = 25C 20 TJ = 125C 0 0.5 VIN = 20V 500 50 0 3083 G21 VCONTROL Pin Current 1 1.5 2 LOAD CURRENT (A) 2.5 VIN = 10V 400 VIN = 5V 300 ADD 1N4148 FOR RTEST < 1k SET PIN = 0V VIN VOUT 200 RTEST 100 10 2 4 6 8 10 12 14 16 18 IN-TO-OUT DIFFERENTIAL (VIN - VOUT) (V) 0.5 3083 G20 VCONTROL Pin Current 60 1 1.0 3083 G19 80 2 0 1.0 -0.5 20 40 60 80 100 120 140 160 180 200 TIME (s) IN/ VCONTROL VOLTAGE (V) 3 OUTPUT VOLTAGE (V) 4 3 4 OUTPUT VOLTAGE (mV) 5 4 5 IN/ VCONTROL VOLTAGE (V) VOUT = 1V ILOAD = 10mA COUT = 10F CERAMIC CSET = 0.1F 6 Turn-On Response 6 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE DEVIATION (mV) IN/ VCONTROL VOLTAGE (V) 7 3 3083 G23 0 0 500 1000 RSET () 1500 2000 3083 G24 3083fa 7 LT3083 TYPICAL PERFORMANCE CHARACTERISTICS Ripple Rejection, Dual Supply, VCONTROL Pin Ripple Rejection, Single Supply ILOAD = 0.1A RIPPLE REJECTION (dB) RIPPLE REJECTION (dB) 80 70 60 50 ILOAD = 1.5A ILOAD = 0.5A 40 30 COUT = 10F CERAMIC 20 CSET = 0.1F CERAMIC 10 RIPPLE = 50mVP-P VIN - VCONTROL = VOUT(NOMINAL) + 2V 0 10 100 1k 10k 100k 1M FREQUENCY (Hz) Ripple Rejection, Dual Supply, IN Pin 120 120 105 105 ILOAD = 0.1A 90 RIPPLE REJECTION (dB) 100 90 TA = 25C, unless otherwise noted. 75 60 I LOAD = 1.5A 45 30 15 10M 0 COUT = 10F CERAMIC CSET = 0.1F VIN = VOUT(NOMINAL) + 1V VCONTROL = VOUT(NOMINAL) + 2V 10 100 1M 75 60 3083 G25 ILOAD = 1.5A 45 30 0 10M ILOAD = 0.5A 90 15 1k 10k 100k FREQUENCY (Hz) ILOAD = 0.1A COUT = 10F CERAMIC CSET = 0.1F VIN = VOUT(NOMINAL) + 1V VCONTROL = VOUT(NOMINAL) + 2V 10 100 1k 10k 100k FREQUENCY (Hz) 3083 G26 Ripple Rejection (120Hz) 1M 10M 3083 G27 Noise Spectral Density 80 1000 100 100 10 79 ERROR AMPLIFIER NOISE SPECTRAL DENSITY (nV/Hz) RIPPLE REJECTOIN (dB) 77 76 75 74 73 72 71 VIN = VCONTROL = VOUT(NOMINAL) + 2V RIPPLE = 500mVP-P, = 120Hz ILOAD = 0.5A CSET = 0.1F, COUT = 10F 70 -50 -25 0 10 25 50 75 100 125 150 TEMPERATURE (C) 10 100 1 100k 1k 10k FREQUENCY (Hz) 3083 G28 3083 G29 Output Voltage Noise Error Amplifier Gain and Phase 21 36 18 0 GAIN (dB) 15 VOUT 100V/DIV PHASE -36 12 -72 9 -108 6 -144 3 -180 0 -3 -216 GAIN -252 -6 -288 ILOAD = 0.5A ILOAD = 1.5A ILOAD = 3A -9 -12 TIME 1ms/DIV VOUT = 1V, RSET = 20k CSET = 0.1F, COUT = 10F ILOAD = 3A REFERENCE CURRENT NOISE SPECTRAL DENSITY (pA/Hz) 78 3083 G30 -15 10 100 1k 10k FREQUENCY (Hz) -324 -360 100k -396 1M 3083 G31 3083fa 8 LT3083 PIN FUNCTIONS (DF/FE/Q/T Packages) OUT (Pins 1-5,13/Pins 1-6,8,9,16,17/ Pin 3, Tab/Pin 3, Tab): Output. The exposed pad of the DF package (Pin 13) and the FE package (Pin 17) and the Tab of the DD-PAK and TO-220 packages is an electrical connection to OUT. Connect the exposed pad of the DF and FE packages and the Tab of the DD-PAK package directly to OUT on the PCB and the respective OUT pins for each package. There must be a minimum load current of 1mA or the output may not regulate. VCONTROL (Pins 7,8/Pins 10,11/Pin 4/Pin 4): Bias Supply. This is the supply pin for the control circuitry of the device. Minimum input capacitance is 2.2F (see Input Capacitance and Stability in the Applications Information section). The current flow into this pin is about 1.7% of the output current. For the device to regulate, this voltage must be more than 1.2V to 1.4V greater than the output voltage (see dropout specifications in the Electrical Characteristics section). SET (Pin 6/Pin 7/Pin 2/Pin 2): Set Point. This pin is the non-inverting input to the error amplifier and the regulation set point. A fixed current of 50A flows out of this pin through a single external resistor, which programs the output voltage of the device. Output voltage range is zero to the VIN(MAX) - VDROPOUT. Transient performance can be improved by adding a small capacitor from the SET pin to ground. IN (Pins 9-12/Pins 12-15/Pin 5/Pin 5): Power Input. This is the collector to the power device of the LT3083. The output load current is supplied through this pin. Minimum IN capacitance is 10F (see Input Capacitance and Stability in Applications Information section). For the device to regulate, the voltage at this pin must be more than 0.1V to 0.5V greater than the output voltage (see dropout specifications in the Electrical Characteristics section). NC (NA/NA/Pin 1/Pin 1): No Connection. No Connect pins have no connection to internal circuitry and may be tied to VIN, VCONTROL, VOUT, GND, or floated. BLOCK DIAGRAM IN VCONTROL 50A + - 3083 BD SET OUT 3083fa 9 LT3083 APPLICATIONS INFORMATION The LT3083 regulator is easy to use and has all the protection features expected in high performance regulators. Included are short-circuit protection and safe operating area protection, as well as thermal shutdown with hysteresis. The LT3083 fits well in applications needing multiple rails. This new architecture adjusts down to zero with a single resistor, handling modern low voltage digital IC's as well as allowing easy parallel operation and thermal management without heat sinks. Adjusting to zero output allows shutting off the powered circuitry. When the input is pre-regulated, such as with a 5V or 3.3V input supply, external resistors can help spread the heat. A precision "0" TC 50A reference current source connects to the noninverting input of a power operational amplifier. The power operational amplifier provides a low impedance buffered output to the voltage on the noninverting input. A single resistor from the noninverting input to ground sets the output voltage. If this resistor is set to 0, zero output voltage results. Therefore, any output voltage can be obtained between zero and the maximum defined by the input power supply. The benefit of using a true internal current source as the reference, as opposed to a bootstrapped reference in older regulators, is not so obvious in this architecture. A true reference current source allows the regulator to have gain and frequency response independent of the impedance on the positive input. On older adjustable regulators, such as the LT1086, loop gain changes with output voltage and bandwidth changes if the adjustment pin is bypassed to ground. For the LT3083, the loop gain is unchanged with output voltage changes or bypassing. Output regulation is not a fixed percentage of output voltage, but is a fixed fraction of millivolts. Use of a true current source allows all of the gain in the buffer amplifier to provide regulation, and none of that gain is needed to amplify up the reference to a higher output voltage. The LT3083 has the collector of the output transistor connected to a separate pin from the control input. Since the dropout on the collector (IN pin) is typically only 310mV, two supplies can be used to power the LT3083 to reduce dissipation: a higher voltage supply for the control circuitry and a lower voltage supply for the collector. This increases efficiency and reduces dissipation. To further spread the heat, a resistor inserted in series with the collector moves some of the heat out of the IC to spread it on the PC board (see the section Reducing Power Dissipation). The LT3083 can be operated in two modes. Three terminal mode has the VCONTROL pin connected to the IN pin and gives a limitation of 1.25V dropout. Alternatively, the VCONTROL pin is separately tied to a higher voltage and the IN pin to a lower voltage giving 310mV dropout on the IN pin, minimizing total power dissipation. This allows for a 3A supply regulating from 2.5VIN to 1.8VOUT or 1.8VIN to 1.2VOUT with low power dissipation. Programming Output Voltage The LT3083 sources a 50A reference current that flows out of the SET pin. Connecting a resistor from SET to ground generates a voltage that becomes the reference point for the error amplifier (see Figure 1). The reference voltage equals 50A multiplied by the value of the SET pin resistor. Any voltage can be generated and there is no minimum output voltage for the regulator. LT3083 IN VCONTROL 50A + VIN + + - VCONTROL OUT SET RSET VOUT COUT CSET 3083 F01 VOUT = 50A * RSET Figure 1. Basic Adjustable Regulator 3083fa 10 LT3083 APPLICATIONS INFORMATION Table 1 lists many common output voltages and the closest standard 1% resistor values used to generate that output voltage. OUT Regulation of the output voltage requires a minimum load current of 1mA. For a true zero voltage output operation, return this 1mA load current to a negative supply voltage. Table 1. 1% Resistors for Common Output Voltages VOUT (V) RSET (k) 1 20 1.2 24.3 1.5 30.1 1.8 35.7 2.5 49.9 3.3 66.5 5 100 With the lower level current used to generate the reference voltage, leakage paths to or from the SET pin can create errors in the reference and output voltages. High quality insulation should be used (e.g., Teflon, Kel-F); cleaning of all insulating surfaces to remove fluxes and other residues will probably be required. Surface coating may be necessary to provide a moisture barrier in high humidity environments. Minimize board leakage by encircling the SET pin and circuitry with a guard ring operated at a potential close to itself. Tie the guard ring to the OUT pin. Guard rings on both sides of the circuit board are required. Bulk leakage reduction depends on the guard ring width. 50nA of leakage into or out of the SET pin and its associated circuitry creates a 0.1% reference voltage error. Leakages of this magnitude, coupled with other sources of leakage, can cause significant offset voltage and reference drift, especially over the possible operating temperature range. Figure 2 depicts an example of a guard ring layout. If guard ring techniques are used, this bootstraps any stray capacitance at the SET pin. Since the SET pin is a high impedance node, unwanted signals may couple into the SET pin and cause erratic behavior. This will be most noticeable when operating with minimum output capacitors at full load current. The easiest way GND SET PIN 3083 F02 Figure 2. Guard Ring Layout Example for DF Package to remedy this is to bypass the SET pin with a small amount of capacitance from SET to ground, 10pF to 20pF is sufficient. Stability and Input Capacitance Typical minimum input capacitance is 10F for IN and 2.2F for VCONTROL. These amounts of capacitance work well using low ESR ceramic capacitors when placed close to the LT3083 and the circuit is located in close proximity to the power source. Higher values of input capacitance may be necessary to maintain stability depending on the application. Oscillating regulator circuits are often viewed as a problem of phase margin and inadequate stability with the output capacitor used. More and more frequently, the problem is not the regulator operating without sufficient output capacitance, but instead with too little input capacitance. The entire circuit must be analyzed and debugged as a whole; conditions relating to the input of the regulator cannot be ignored. The LT3083 input presents a high impedance to its power source: the output voltage and load current are independent of input voltage variations. To maintain stability of the regulator circuit as a whole, the LT3083 must be powered from a low impedance supply. When using short supply lines or powering directly from a large switching supply, there is no issue--hundreds or thousands of microfarads of capacitance are available through a low impedance. 3083fa 11 LT3083 APPLICATIONS INFORMATION When longer supply lines, filters, current sense resistors, or other impedances exist between the supply and the input to the LT3083, input bypassing should be reviewed if stability concerns are seen. Just as output capacitance supplies the instantaneous changes in load current for output transients until the regulator is able to respond, input capacitance supplies local power to the regulator until the main supply responds. When impedance separates the LT3083 from its main supply, the local input can droop so that the output follows. The entire circuit may break into oscillations, usually characterized by larger amplitude oscillations on the input and coupling to the output. Low ESR, ceramic input bypass capacitors are acceptable for applications without long input leads. However, applications connecting a power supply to an LT3083 circuit's IN and GND pins with long input wires combined with low ESR, ceramic input capacitors are prone to voltage spikes, reliability concerns and application-specific board oscillations. The input wire inductance found in many battery powered applications, combined with the low ESR ceramic input capacitor, forms a high-Q LC resonant tank circuit. In some instances this resonant frequency beats against the output current dependent LDO bandwidth and interferes with proper operation. Simple circuit modifications/solutions are then required. This behavior is not indicative of LT3083 instability, but is a common ceramic input bypass capacitor application issue. The self-inductance, or isolated inductance, of a wire is directly proportional to its length. Wire diameter is not a major factor on its self-inductance. For example, the selfinductance of a 2-AWG isolated wire (diameter = 0.26") is about half the self-inductance of a 30-AWG wire (diameter = 0.01"). One foot of 30-AWG wire has about 465nH of self-inductance. One of two ways reduces a wire's self-inductance. One method divides the current flowing towards the LT3083 between two parallel conductors. In this case, the farther apart the wires are from each other, the more the self-inductance is reduced; up to a 50% reduction when placed a few inches apart. Splitting the wires basically connects two equal inductors in parallel, but placing them in close proximity gives the wires mutual inductance adding to the self-inductance. The second and most effective way to reduce overall inductance is to place both forward and return current conductors (the input and GND wires) in very close proximity. Two 30-AWG wires separated by only 0.02", used as forward- and return- current conductors, reduce the overall self-inductance to approximately onefifth that of a single isolated wire. If wiring modifications are not permissible for the applications, including series resistance between the power supply and the input of the LT3083 also stabilizes the application. As little as 0.1 to 0.5, often less, is effective in damping the LC resonance. If the added impedance between the power supply and the input is unacceptable, adding ESR to the input capacitor also provides the necessary damping of the LC resonance. However, the required ESR is generally higher than the series impedance required. Stability and Output Capacitance The LT3083 requires an output capacitor for stability. It is designed to be stable with most low ESR capacitors (typically ceramic, tantalum or low ESR electrolytic). A minimum output capacitor of 10F with an ESR of 0.5 or less is recommended to prevent oscillations. Larger values of output capacitance decrease peak deviations and provide improved transient response for larger load current changes. Bypass capacitors, used to decouple individual components powered by the LT3083, increase the effective output capacitor value. For improvement in transient performance, place a capacitor across the voltage setting resistor. Capacitors up to 1F can be used. This bypass capacitor reduces system noise as well, but start-up time is proportional to the time constant of the voltage setting resistor (RSET in Figure 1) and SET pin bypass capacitor. Give extra consideration to the use of ceramic capacitors. Ceramic capacitors are manufactured with a variety of dielectrics, each with different behavior across temperature and applied voltage. The most common dielectrics used are specified with EIA temperature characteristic codes of Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics are good for providing high capacitances in a small package, but they tend to have strong voltage and temperature coefficients as shown in Figures 3 and 4. When used with a 5V regulator, a 16V 10F Y5V capacitor can exhibit an 3083fa 12 LT3083 APPLICATIONS INFORMATION 20 effective value as low as 1F to 2F for the DC bias voltage applied and over the operating temperature range. The X5R and X7R dielectrics result in more stable characteristics and are more suitable for use as the output capacitor. The X7R type has better stability across temperature, while the X5R is less expensive and is available in higher values. Care still must be exercised when using X5R and X7R capacitors. The X5R and X7R codes only specify operating temperature range and maximum capacitance change over temperature. Capacitance change due to DC bias with X5R and X7R capacitors is better than Y5V and Z5U capacitors, but can still be significant enough to drop capacitor values below appropriate levels. Capacitor DC bias characteristics tend to improve as component case size increases, but expected capacitance at operating voltage should be verified. BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F 0 CHANGE IN VALUE (%) X5R -20 -40 -60 Y5V -80 -100 0 2 4 8 6 10 12 DC BIAS VOLTAGE (V) 14 16 3083 F03 Figure 3. Ceramic Capacitor DC Bias Characteristics 40 CHANGE IN VALUE (%) 20 X5R 0 Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress. In a ceramic capacitor, the stress can be induced by vibrations in the system or thermal transients. -20 -40 Y5V -60 -80 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F -100 -50 -25 50 25 75 0 TEMPERATURE (C) 100 Paralleling Devices 125 3083 F04 Figure 4. Ceramic Capacitor Temperature Characteristics VIN LT3083 VCONTROL + - OUT 10m Table 2. PC Board Trace Resistance SET VIN 4.8V TO 20V VIN LT3083 VCONTROL + - 10F Higher output current is obtained by paralleling multiple LT3083s together. Tie the individual SET pins together and tie the individual IN pins together. Connect the outputs in common using small pieces of PC trace as ballast resistors to promote equal current sharing. PC trace resistance in m/inch is shown in Table 2. Ballasting requires only a tiny area on the PCB. WEIGHT (oz) 10mil WIDTH 20mil WIDTH 1 54.3 27.1 2 27.1 13.6 Trace resistance is measured in m/in OUT 10m SET VOUT 3.3V 6A 10F 33k 3083 F05 Figure 5. Parallel Devices The worst-case room temperature offset, only 4mV (DD-PAK, T Packages) between the SET pin and the OUT pin, allows the use of very small ballast resistors. As shown in Figure 5, each LT3083 has a small 10m ballast resistor, which at full output current gives better than 80% equalized sharing of the current. The external 3083fa 13 LT3083 APPLICATIONS INFORMATION resistance of 10m (5m for the two devices in parallel) only adds about 30mV of output regulation drop at an output of 6A. With an output voltage of 3.3V, this only adds 1% to the regulation. Of course, paralleling more than two LT3083s yields even higher output current. Spreading the devices on the PC board also spreads the heat. Series input resistors can further spread the heat if the input-to-output difference is high. Quieting the Noise The LT3083 offers numerous noise performance advantages. Every linear regulator has its sources of noise. In general, a linear regulator's critical noise source is the reference. In addition, consider the error amplifier's noise contribution along with the resistor divider's noise gain. Many traditional low noise regulators bond out the voltage reference to an external pin (usually through a large value resistor) to allow for bypassing and noise reduction. The LT3083 does not use a traditional voltage reference like other linear regulators. Instead, it uses a 50A reference current. The 50A current source generates noise current levels of 3.16pA/Hz (1nARMS) over the 10Hz to 100kHz bandwidth). The equivalent voltage noise equals the RMS noise current multiplied by the resistor value. The SET pin resistor generates spot noise equal to 4kTR (k = Boltzmann's constant, 1.38 * 10-23J/K, and T is absolute temperature) which is RMS summed with the voltage noise. If the application requires lower noise performance, bypass the voltage setting resistor with a capacitor to GND. Note that this noise-reduction capacitor increases start-up time as a factor of the RC time constant. The LT3083 uses a unity-gain follower from the SET pin to the OUT pin. Therefore, multiple possibilities exist (besides a SET pin resistor) to set output voltage. For example, using a high accuracy voltage reference from SET to GND removes the errors in output voltage due to reference current tolerance and resistor tolerance. Active driving of the SET pin is acceptable. The typical noise scenario for a linear regulator is that the output voltage setting resistor divider gains up the noise reference, especially if VOUT is much greater than VREF. The LT3083's noise advantage is that the unity gain follower presents no noise gain whatsoever from the SET pin to the output. Thus, noise figures do not increase accordingly. Error amplifier noise is typically 126.5nV/Hz (40VRMS) over the 10Hz to 100kHz bandwidth). The error amplifier's noise is RMS summed with the other noise terms to give a final noise figure for the regulator. Curves in the Typical Performance Characteristics section show noise spectral density and peak-to-peak noise characteristics for both the reference current and error amplifier over the 10Hz to 100kHz bandwidth. Load Regulation The LT3083 is a floating device. No ground pin exists on the packages. Thus, the IC delivers all quiescent current and drive current to the load. Therefore, it is not possible to provide true remote load sensing. The connection resistance between the regulator and the load determines load regulation performance. The data sheet's load regulation specification is Kelvin sensed at the package's pins. Negative-side sensing is a true Kelvin connection by returning the bottom of the voltage setting resistor to the negative side of the load (see Figure 6). Connected as shown, system load regulation is the sum of the LT3083's load regulation and the parasitic line resistance multiplied by the output current. To minimize load regulation, keep the positive connection between the regulator and load as short as possible. If possible, use large diameter wire or wide PC board traces. IN LT3083 VCONTROL + - SET RSET PARASITIC RESISTANCE OUT RP RP LOAD RP 3080 F06 Figure 6. Connections for Best Load Regulation 3083fa 14 LT3083 APPLICATIONS INFORMATION Thermal Considerations Table 4. FE Package, 16-Lead TSSOP The LT3083's internal power and thermal limiting circuitry protects itself under overload conditions. For continuous normal load conditions, do not exceed the 125C maximum junction temperature. Carefully consider all sources of thermal resistance from junction-to-ambient. This includes (but is not limited to) junction-to-case, case-to-heat sink interface, heat sink resistance or circuit board-to-ambient as the application dictates. Consider all additional, adjacent heat generating sources in proximity on the PCB. Surface mount packages provide the necessary heat sinking by using the heat spreading capabilities of the PC board, copper traces, and planes. Surface mount heat sinks, plated through-holes and solder-filled vias can also spread the heat generated by power devices. Junction-to-case thermal resistance is specified from the IC junction to the bottom of the case directly, or the bottom of the pin most directly in the heat path. This is the lowest thermal resistance path for heat flow. Only proper device mounting ensures the best possible thermal flow from this area of the packages to the heat sinking material. Note that the exposed pad of the DFN and TSSOP packages and the tab of the DD-PAK and TO-220 packages are electrically connected to the output (VOUT). Tables 3 through 5 list thermal resistance as a function of copper areas on a fixed board size. All measurements were taken in still air on a 4-layer FR-4 board with 1oz solid internal planes and 2oz external trace planes with a total finished board thickness of 1.6mm. Layers are not connected electrically or thermally. Table 3. DF Package, 12-Lead DFN COPPER AREA THERMAL RESISTANCE BOARD AREA (JUNCTION-TO-AMBIENT) TOPSIDE* BACKSIDE 2500mm2 2500mm2 2500mm2 18C/W 1000mm2 2500mm2 2500mm2 22C/W 225mm2 2500mm2 2500mm2 29C/W 100mm2 2500mm2 2500mm2 35C/W COPPER AREA THERMAL RESISTANCE BOARD AREA (JUNCTION-TO-AMBIENT) TOPSIDE* BACKSIDE 2500mm2 2500mm2 2500mm2 16C/W 1000mm2 2500mm2 2500mm2 20C/W 225mm2 2500mm2 2500mm2 26C/W 100mm2 2500mm2 2500mm2 32C/W *Device is mounted on topside. Table 5. Q Package, 5-Lead DD-PAK COPPER AREA THERMAL RESISTANCE BOARD AREA (JUNCTION-TO-AMBIENT) TOPSIDE* BACKSIDE 2500mm2 2500mm2 2500mm2 13C/W 1000mm2 2500mm2 2500mm2 14C/W 125mm2 2500mm2 2500mm2 16C/W *Device is mounted on topside. T Package, 5-Lead TO-220 Thermal Resistance (Junction-to-Case) = 3C/W For further information on thermal resistance and using thermal information, refer to JEDEC standard JESD51, notably JESD51-12. PCB layers, copper weight, board layout and thermal vias affect the resultant thermal resistance. Tables 3 through 5 provide thermal resistance numbers for best-case 4-layer boards with 1oz internal and 2oz external copper. Modern, multilayer PCBs may not be able to achieve quite the same level performance as found in these tables. Calculating Junction Temperature Example: Given an output voltage of 0.9V, a VCONTROL voltage of 3.3V 10%, an IN voltage of 1.5V 5%, output current range from 10mA to 3A and a maximum ambient temperature of 50C, what will the maximum junction temperature be for the DD-PAK on a 2500mm2 board with topside copper of 1000mm2? *Device is mounted on topside. 3083fa 15 LT3083 APPLICATIONS INFORMATION The power in the drive circuit equals: PDRIVE = (VCONTROL - VOUT)(ICONTROL) where ICONTROL is equal to IOUT/60. ICONTROL is a function of output current. A curve of ICONTROL vs IOUT can be found in the Typical Performance Characteristics curves. The total power equals: PTOTAL = PDRIVE + POUTPUT The current delivered to the SET pin is negligible and can be ignored. VCONTROL(MAX_CONTINUOUS) = 3.630V (3.3V + 10%) VIN(MAX_CONTINUOUS) = 1.575V (1.5V + 5%) VOUT = 0.9V, IOUT = 3A, TA = 50C Power dissipation under these conditions is equal to: PDRIVE = (VCONTROL - VOUT)(ICONTROL) ICONTROL = IOUT 3A = = 50mA 60 60 PDRIVE = (3.630V - 0.9V)(50mA) = 137mW POUTPUT = (VIN - VOUT)(IOUT) As an example, assume: VIN = VCONTROL = 5V, VOUT = 3.3V and IOUT(MAX) = 2A. Use the formulas from the Calculating Junction Temperature section previously discussed. Without series resistor RS, power dissipation in the LT3083 equals: 2A PTOTAL = (5V - 3.3V ) * + (5V - 3.3V ) * 2A 60 = 3.46W If the voltage differential (VDIFF) across the NPN pass transistor is chosen as 0.5V, then RS equals: RS = 5V - 3.3V - 0.5V = 0.6 2A Power dissipation in the LT3083 now equals: 2A PTOTAL = (5V - 3.3V ) * + 0.5V * 2A = 1.06W 60 The LT3083's power dissipation is now only 30% compared to no series resistor. RS dissipates 2.4W of power. Choose appropriate wattage resistors or use multiple resistors in parallel to handle and dissipate the power properly. POUTPUT = (1.575V - 0.9V)(3A) = 2.03W Total Power Dissipation = 2.16W C1 VIN VCONTROL LT3083 IN RS VIN Junction Temperature will be equal to: TJ = TA + PTOTAL * JA (using tables) + - TJ = 50C + 2.16W * 16C/W = 84.6C In this case, the junction temperature is below the maximum rating, ensuring reliable operation. SET OUT 3083 F07 VOUT C2 RSET Reducing Power Dissipation In some applications it may be necessary to reduce the power dissipation in the LT3083 package without sacrificing output current capability. Two techniques are available. The first technique, illustrated in Figure 7, employs a resistor in series with the regulator's input. The voltage drop across RS decreases the LT3083's input-to-output differential voltage and correspondingly decreases the LT3083's power dissipation. Figure 7. Reducing Power Dissipation Using a Series Resistor 3083fa 16 LT3083 APPLICATIONS INFORMATION The second technique for reducing power dissipation, shown in Figure 8, uses a resistor in parallel with the LT3083. This resistor provides a parallel path for current flow, reducing the current flowing through the LT3083. This technique works well if input voltage is reasonably constant and output load current changes are small. This technique also increases the maximum available output current at the expense of minimum load requirements. C1 Calculating RP yields: 5.5V - 3.2V = 3.65 0.63A (5% Standard Value = 3.6) RP = VIN VCONTROL LT3083 The maximum total power dissipation is (5.5V - 3.2V) * 2A = 4.6W. However, the LT3083 supplies only: IN 2A - RP + - SET As an example, assume: VIN = VCONTROL = 5V, VIN(MAX) = 5.5V, VOUT = 3.3V, VOUT(MIN) = 3.2V, IOUT(MAX) = 2A and IOUT(MIN) = 0.7A. Also, assuming that RP carries no more than 90% of IOUT(MIN) = 630mA. OUT 3083 F08 VOUT C2 RSET Figure 8. Reducing Power Dissipation Using a Parallel Resistor 5.5V - 3.2V = 1.36A 3.6 Therefore, the LT3083's power dissipation is only: PDISS = (5.5V - 3.2V) * 1.36A = 3.13W RP dissipates 1.47W of power. As with the first technique, choose appropriate wattage resistors to handle and dissipate the power properly. With this configuration, the LT3083 supplies only 1.36A. Therefore, load current can increase by 1.64A to a total output current of 3.64A while keeping the LT3083 in its normal operating range. 3083fa 17 LT3083 TYPICAL APPLICATIONS Adding Shutdown LT3083 IN VIN Current Source VCONTROL VCONTROL + - + - 10F OUT Q1 VN2222LL OUT 0.33 VOUT SET ON OFF LT3083 IN VIN 10V SET 10F Q2* VN2222LL R1 SHUTDOWN IOUT 0A TO 3A 20k 3083 TA03 3083 TA02 *Q2 INSURES ZERO OUTPUT IN THE ABSENCE OF ANY OUTPUT LOAD. Low Dropout Voltage LED Driver C1 VIN VCONTROL LT3083 IN + - 1A D1 OUT SET R1 20k R2 1 3083 TA04 DAC-Controlled Regulator LT3083 IN VIN VCONTROL 150k SPI LTC2641 150k + - 450k - + SET OUT VOUT 10F 3083 TA05 LT1991 GAIN = 4 3083fa 18 LT3083 TYPICAL APPLICATIONS Coincident Tracking LT3083 IN VCONTROL LT3083 IN + - VCONTROL LT3083 IN VIN 7V TO 20V + - VCONTROL + - C1 10F SET SET R1 49.9k 34k OUT SET R2 16.2k OUT OUT VOUT3 5V 10F 3083 TA06 VOUT2 3.3V C3 10F VOUT1 2.5V C2 10F Adding Soft-Start LT3083 IN VIN 4.8V to 20V VCONTROL + - D1 1N4148 C1 10F OUT SET C2 0.01F VOUT 3.3V 3A COUT 10F R1 66.5k 3083 TA07 Lab Supply LT3083 IN VIN 12V TO 18V VCONTROL VCONTROL + LT3083 IN + - 15F + - OUT 0.33 + SET 20k 0A TO 3A 15F SET R4 200k OUT 10F + VOUT 0V TO 10V 100F 3083 TA08 3083fa 19 LT3083 TYPICAL APPLICATIONS High Voltage Regulator 6.1V 10k VIN 50V 1N4148 IN LT3083 BUZ11 VCONTROL + + - 10F 15F VOUT 3A OUT SET RSET 402k + VOUT = 20V VOUT = 50A * RSET 10F 3083 TA09 Ramp Generator LT3083 IN VIN 5V Reference Buffer VCONTROL VCONTROL + - 10F + - OUT VOUT SET VN2222LL LT3083 IN VIN 10F VN2222LL 10nF INPUT LT1019 OUTPUT SET C1 1F GND OUT VOUT* C2 10F 3083 TA11 *MIN LOAD 0.5mA 3083 TA10 Boosting Fixed Output Regulators LT3083 IN VCONTROL + - 10m SET 5V LT1963-3.3 10F OUT 20m 42* 3.3VOUT 4.5A 47F 3083 TA12 33k *4mV DROP ENSURES LT3083 IS OFF WITH NO LOAD MULTIPLE LT3083'S CAN BE USED 3083fa 20 LT3083 TYPICAL APPLICATIONS Low Voltage, High Current Adjustable High Efficiency Regulator* 0.47H PVIN 2.7V TO 5.5V 2x 100F + ITH SVIN 2.2MEG 100k 10k SW LTC3610 RT + 12.1k 470pF 294k PGOOD 2x 100F 2N3906 LT3083 IN VCONTROL RUN/SS + - VFB 1000pF OUT 78.7k SGND PGND 10m SET SYNC/MODE 124k LT3083 IN VCONTROL + - *DIFFERENTIAL VOLTAGE ON LT3083 IS 0.6V SET BY THE VBE OF THE 2N3906 PNP. OUT MAXIMUM OUTPUT VOLTAGE IS 1.5V BELOW INPUT VOLTAGE 10m SET 0V TO 4V 12A LT3083 IN VCONTROL + - OUT 10m SET LT3083 IN VCONTROL + - SET OUT 3083 TA13 100k 10m + 100F 3083fa 21 LT3083 TYPICAL APPLICATIONS Adjustable High Efficiency Regulator* 4.5V TO 25V VIN 10F 1F BOOST 0.47F BD LT3680 100k RUN/SS 4.7H 0.1F 68F B340A 680pF RT 63.4k GND VCONTROL TP0610L VCONTROL 15.4k LT3083 IN SW FB + - 200k OUT 10k SET 600kHz 3083 TA14 0V TO 10V 3A 4.7F 200k *DIFFERENTIAL VOLTAGE ON LT3083 1.4V SET BY THE TPO610L P-CHANNEL THRESHOLD. MAXIMUM OUTPUT VOLTAGE IS 2V BELOW INPUT VOLTAGE 10k 2 Terminal Current Source CCOMP* IN LT3083 VCONTROL + - SET *CCOMP R1 10 10F R1 10 2.2F R1 20k 3083 TA15 IOUT = 1V R1 3083fa 22 LT3083 PACKAGE DESCRIPTION FE Package 16-Lead Plastic TSSOP (4.4mm) FELTC Package (Reference DWG # 05-08-1663 Rev H) 16-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG #Pad 05-08-1663 Exposed VariationRev BB H) Exposed Pad Variation BB 4.90 - 5.10* (.193 - .201) 3.58 (.141) 3.58 (.141) 16 1514 13 12 1110 6.60 0.10 4.50 0.10 9 2.94 (.116) 2.94 6.40 (.116) (.252) BSC SEE NOTE 4 0.45 0.05 1.05 0.10 0.65 BSC 1 2 3 4 5 6 7 8 RECOMMENDED SOLDER PAD LAYOUT 4.30 - 4.50* (.169 - .177) 0.09 - 0.20 (.0035 - .0079) 0.50 - 0.75 (.020 - .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 0.25 REF 1.10 (.0433) MAX 0 - 8 0.65 (.0256) BSC 0.195 - 0.30 (.0077 - .0118) TYP 0.05 - 0.15 (.002 - .006) FE16 (BB) TSSOP REV G 0910 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 3083fa 23 LT3083 PACKAGE DESCRIPTION DF Package 12-Lead Plastic DFN (4mm x 4mm) (Reference LTC DWG # 05-08-1733 Rev O) 2.50 REF 0.70 0.05 3.38 0.05 4.50 0.05 3.10 0.05 2.65 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 4.00 0.10 (4 SIDES) 2.50 REF 7 12 0.40 0.10 3.38 0.10 2.65 0.10 PIN 1 NOTCH R = 0.20 TYP OR 0.35 x 45 CHAMFER PIN 1 TOP MARK (NOTE 6) 0.200 REF 6 R = 0.115 TYP 0.75 0.05 1 (DF12) DFN 0806 REV O 0.25 0.05 0.50 BSC BOTTOM VIEW--EXPOSED PAD 0.00 - 0.05 NOTE: 1. DRAWING IS PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)--TO BE APPROVED 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3083fa 24 LT3083 PACKAGE DESCRIPTION Q Package Q Package 5-Lead Plastic DDDD-PAK Pak 5-Lead Plastic (Reference LTCLTC DWG # 05-08-1461 Rev E)E) (Reference DWG # 05-08-1461 Rev .256 (6.502) .060 (1.524) TYP .060 (1.524) .390 - .415 (9.906 - 10.541) .165 - .180 (4.191 - 4.572) .045 - .055 (1.143 - 1.397) 15 TYP .060 (1.524) .183 (4.648) +.008 .004 -.004 +0.203 0.102 -0.102 .059 (1.499) TYP .330 - .370 (8.382 - 9.398) ( ) .095 - .115 (2.413 - 2.921) .075 (1.905) .300 (7.620) +.012 .143 -.020 +0.305 3.632 -0.508 ( BOTTOM VIEW OF DD PAK HATCHED AREA IS SOLDER PLATED COPPER HEAT SINK .067 (1.702) .028 - .038 BSC (0.711 - 0.965) TYP ) .420 .276 .080 .420 .050 .012 (1.270 0.305) .013 - .023 (0.330 - 0.584) .325 .350 .205 .585 .585 .320 .090 .090 .067 .042 RECOMMENDED SOLDER PAD LAYOUT NOTE: 1. DIMENSIONS IN INCH/(MILLIMETER) 2. DRAWING NOT TO SCALE .067 .042 RECOMMENDED SOLDER PAD LAYOUT FOR THICKER SOLDER PASTE APPLICATIONS Q(DD5) 0610 REV E 3083fa 25 LT3083 PACKAGE DESCRIPTION T Package 5-Lead Plastic TO-220 (Standard) (Reference LTC DWG # 05-08-1421) .390 - .415 (9.906 - 10.541) .165 - .180 (4.191 - 4.572) .147 - .155 (3.734 - 3.937) DIA .045 - .055 (1.143 - 1.397) .230 - .270 (5.842 - 6.858) .460 - .500 (11.684 - 12.700) .570 - .620 (14.478 - 15.748) .330 - .370 (8.382 - 9.398) .700 - .728 (17.78 - 18.491) .620 (15.75) TYP SEATING PLANE .152 - .202 .260 - .320 (3.861 - 5.131) (6.60 - 8.13) BSC .067 (1.70) .095 - .115 (2.413 - 2.921) .155 - .195* (3.937 - 4.953) .013 - .023 (0.330 - 0.584) .028 - .038 (0.711 - 0.965) .135 - .165 (3.429 - 4.191) * MEASURED AT THE SEATING PLANE T5 (TO-220) 0801 3083fa 26 LT3083 REVISION HISTORY REV DATE DESCRIPTION PAGE NUMBER A 4/11 Revised part markings in Order Information section 3 3083fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 27 LT3083 TYPICAL APPLICATION Paralleling Regulators IN LT3083 VCONTROL + - OUT 10m SET IN VIN 4.8V TO 28V LT3083 VCONTROL + - 10F OUT 10m VOUT 3.3V 6A SET 33.2k 22F 3083 TA16 RELATED PARTS PART NUMBER LT1185 LT1764/ LT1764A LT1963/A LT1965 LT3022 DESCRIPTION 3A Negative Low Dropout Regulator 3A, Fast Transient Response, Low Noise LDO 1.5A Low Noise, Fast Transient Response LDO 1.1A, Low Noise, Low Dropout Linear Regulator 1A, Low Voltage, VLDO Linear Regulator LT3070 5A, Low Noise, Programmable VOUT, 85mV Dropout Linear Regulator with Digital Margining LT3071 5A, Low Noise, Programmable Vout, 85mV Dropout Linear Regulator with Analog Margining LT3080/ LT3080-1 1.1A, Parallelable, Low Noise, Low Dropout Linear Regulator LT3082 200mA, Parallelable, Single Resistor, Low Dropout Linear Regulator LT3085 500mA, Parallelable, Low Noise, Low Dropout Linear Regulator LTC3026 1.5A, Low Input Voltage VLDO Linear Regulator COMMENTS VIN: -4.5V to -35V, 0.8V Dropout Voltage, DD-PAK and TO-220 Packages 340mV Dropout Voltage, Low Noise: 40VRMS, VIN = 2.7V to 20V, TO-220 and DD Packages. "A" Version Stable Also with Ceramic Capacitors 340mV Dropout Voltage, Low Noise: 40VRMS, VIN = 2.5V to 20V, "A" Version Stable with Ceramic Capacitors, TO-220, DD, SOT-223 and SO-8 Packages 290mV Dropout Voltage, Low Noise: 40VRMS, VIN: 1.8V to 20V, VOUT: 1.2V to 19.5V, Stable with Ceramic Capacitors, TO-220, DD-PAK, MSOP and 3mm x 3mm DFN Packages VIN: 0.9V to 10V, Dropout Voltage: 145mV Typical, Adjustable Output (VREF = VOUT(MIN) = 200mV), Stable with Low ESR, Ceramic Output Capacitors, 16-Pin DFN (5mm x 3mm) and 16-Lead MSOP Packages Dropout Voltage: 85mV, Digitally Programmable VOUT: 0.8V to 1.8V, Digital Output Margining: 1%, 3% or 5%, Low Output Noise: 25VRMS (10Hz to 100kHz), Parallelable: Use Two for a 10A Output, Stable with Low ESR Ceramic Output Capacitors (15F Minimum), 28-Lead 4mm x 5mm QFN Package Dropout Voltage: 85mV, Digitally Programmable VOUT: 0.8V to 1.8V, Analog Margining: 10%, Low Output Noise: 25VRMS (10Hz to 100kHz), Parallelable: Use Two for a 10A Output, IMON Output Current Monitor, Stable with Low ESR Ceramic Output Capacitors (15F Minimum), 28-Lead 4mm x 5mm QFN Package 300mV Dropout Voltage (2-Supply Operation), Low Noise: 40VRMS, VIN : 1.2V to 36V, VOUT: 0V to 35.7V, Current-Based Reference with 1-Resistor VOUT Set; Directly Parallelable (No Op Amp Required), Stable with Ceramic Capacitors, TO-220, DD-PAK, SOT-223, MS8E and 3mm x 3mm DFN-8 Packages; "-1" Version Has Integrated Internal Ballast Resistor Outputs May Be Paralleled for Higher Output, Current or Heat Spreading, Wide Input Voltage Range: 1.2V to 40V, Low Value Input/Output Capacitors Required: 0.22F, Single Resistor Sets Output Voltage, 8-Lead SOT-23, 3-Lead SOT-223 and 8-Lead 3mm x 3mm DFN Packages 275mV Dropout Voltage (2-Supply Operation), Low Noise: 40VRMS, VIN: 1.2V to 36V, VOUT: 0V to 35.7V, Current-Based Reference with 1-Resistor VOUT Set; Directly Parallelable (No Op Amp Required), Stable with Ceramic Capacitors, MS8E and 2mm x 3mm DFN-6 Packages VIN: 1.14V to 3.5V (Boost Enabled), 1.14V to 5.5V (with External 5V), VDO = 0.1V, IQ = 950A, Stable with 10F Ceramic Capacitors, 10-Lead MSOP-E and DFN-10 Packages 3083fa 28 Linear Technology Corporation LT 0411 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2011