1
Features
Low-voltage and Standard-voltage Operation
2.7 (VCC = 2.7V to 5.5V)
1.8 (VCC = 1.8V to 3.6V)
Internally Organized 16,384 x 8 and 32,768 x 8
Two-wire Serial Interface
Schmitt Trigger, Filtered Inputs for Noise Suppression
Bidirectional Data Transfer Protocol
1 MHz (5V), 400 kHz (2.7V, 2.5V) and 100 kHz (1.8V) Compatibility
Write Protect Pin for Hardware and Software Data Protection
64-byte Page Write Mode (Partial Page Writes Allowed)
Self-timed Write Cycle (5 ms Max)
High Reliability
Endurance: One Million Write Cycles
Data Retention: 40 Years
Extended Temperature and Lead-free/Halogen-free
Devices Available
8-lead JEDEC PDIP, 8-lead JEDEC and EIAJ SOIC, 8-lead MAP, 8-lead TSSOP, 8-lead
SAP and 8-ball dBGA2 Packages
Die Sales: Wafer Form, Waffle Pack, and Bumped Wafers
Description
The AT24C128/256 provides 131,072/262,144 bits of serial electrically erasable and
programmable read only memory (EEPROM) organized as 16,384/32,768 words of 8
bits each. The device’s cascadable feature allows up to 4 devices to share a common
Two-wire bus. The device is optimized for use in many industrial and commercial appli-
cations where low power and low voltage operation are essential. The devices are
available in space-saving 8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead EIAJ
SOIC, 8-lead MAP (24C128), 8-lead TSSOP, 8-lead SOIC Array Package and 8-ball
dBGA2 packages. In addition, the entire family is available in 2.7V (2.7V to 5.5V) and
1.8V (1.8V to 3.6V) versions.
Table 1. Pin Configuration
Pin Name Function
A0 - A1 Address Inputs
SDA Serial Data
SCL Serial Clock Input
WP Write Protect
NC No Connect
GND Ground
8-lead SAP
Bottom View
1
2
3
4
8
7
6
5
VCC
WP
SCL
SDA
A0
A1
NC
GND
Two-wire Serial
EEPROMs
128K (16,384 x 8)
256K (32,768 x 8)
AT24C128
AT24C256
Rev. 0670O–SEEPR–2/05
8-lead PDIP
1
2
3
4
8
7
6
5
A0
A1
NC
GND
VCC
WP
SCL
SDA
8-lead SOIC
1
2
3
4
8
7
6
5
A0
A1
NC
GND
VCC
WP
SCL
SDA
8-ball dBGA2
Bottom View
VCC
WP
SCL
SDA
A0
A1
NC
GND
1
2
3
4
8
7
6
5
8-lead TSSOP
1
2
3
4
8
7
6
5
A0
A1
NC
GND
VCC
WP
SCL
SDA
8-lead MAP
Bottom View
1
2
3
4
8
7
6
5
VCC
WP
SCL
SDA
A0
A1
NC
GND
2AT24C128/256
0670O–SEEPR–2/05
Figure 1. Block Diagram
Absolute Maximum Ratings*
Operating Temperature..................................–55°C to +125°C*NOTICE: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Storage Temperature.....................................–65°C to +150°C
Voltage on Any Pin
with Respect to Ground ....................................–1.0V to +7.0V
Maximum Operating Voltage .......................................... 6.25V
DC Output Current........................................................ 5.0 mA
3
AT24C128/256
0670O–SEEPR–2/05
Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each
EEPROM device and negative edge clock data out of each device.
SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-
drain driven and may be wire-ORed with any number of other open-drain or open collector
devices.
DEVICE/ADDRESSES (A1, A0): The A1 and A0 pins are device address inputs that are hard-
wired or left not connected for hardware compatibility with other AT24CXX devices. When the
pins are hardwired, as many as four 128K/256K devices may be addressed on a single bus
system (device addressing is discussed in detail under the Device Addressing section). If the
pins are left floating, the A1 and A0 pins will be internally pulled down to GND if the capacitive
coupling to the circuit board VCC plane is <3 pF. If coupling is >3 pF, Atmel recommends con-
necting the address pins to GND.
WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write
operations. When WP is connected high to VCC, all write operations to the memory are inhib-
ited. If the pin is left floating, the WP pin will be internally pulled down to GND if the capacitive
coupling to the circuit board VCC plane is <3 pF. If coupling is >3 pF, Atmel recommends con-
necting the pin to GND.
Memory
Organization
AT24C128/256, 128K/256K SERIAL EEPROM: The 128K/256K is internally organized as
256/512 pages of 64-bytes each. Random word addressing requires a 14/15-bit data word
address.
4AT24C128/256
0670O–SEEPR–2/05
Table 2. Pin Capacitance(1)
Note: 1. This parameter is characterized and is not 100% tested.
Table 3. DC Characteristics(1)
Notes: 1. VIL min and VIH max are reference only and are not tested.
2. The AT24C128/256 bearing the process letter “B” on the package (the mark is located in the lower right corner on the top-
side of the package) are approved for operation in the extended temperature range.
Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V.
Symbol Test Condition Max Units Conditions
CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V
CIN Input Capacitance (A0, A1, SCL) 6 pF VIN = 0V
Applicable over recommended operating range from: TAI = 40°C to +85°C, VCC = +1.8V to +5.5V; TAE= 40°C to +125°C(2),
VCC = +2.7V to +5.5V(unless otherwise noted).
Symbol Parameter Test Condition Min Typ Max Units
VCC1 Supply Voltage 1.8 3.6 V
VCC2 Supply Voltage 2.5 5.5 V
VCC3 Supply Voltage 4.5 5.5 V
ICC1 Supply Current VCC = 5.0V READ at 400 kHz 1.0 2.0 mA
ICC2 Supply Current VCC = 5.0V WRITE at 400 kHz 2.0 3.0 mA
ISB1
Standby Current
(1.8V option)
VCC = 1.8V VIN = VCC or VSS
0.2 µA
VCC = 3.6V 2.0
ISB2
Standby Current
(2.5V option)
VCC = 2.5V VIN = VCC or VSS
0.5 µA
VCC = 5.5V 6.0
ISB3
Standby Current
(5.0V option) VCC = 4.5 - 5.5V VIN = VCC or VSS 6.0 µA
ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 µA
ILO
Output Leakage
Current VOUT = VCC or VSS 0.05 3.0 µA
VIL Input Low Level(1) –0.6 VCC x 0.3 V
VIH Input High Level(1) VCC x 0.7 VCC + 0.5 V
VOL2 Output Low Level VCC = 3.0V IOL = 2.1 mA 0.4 V
VOL1 Output Low Level VCC = 1.8V IOL = 0.15 mA 0.2 V
5
AT24C128/256
0670O–SEEPR–2/05
AC Characteristics – Industrial Temperatures
Notes: 1. This parameter is characterized and is not 100% tested.
2. AC measurement conditions:
RL (connects to VCC): 1.3 k (2.5V, 5V), 10 k (1.8V)
Input pulse voltages: 0.3 VCC to 0.7 VCC
Input rise and fall times: 50 ns
Input and output timing reference voltages: 0.5 VCC
3. The Write Cycle Time of 5 ms only applies to the AT24C128/256 devices bearing the process letter “B” on the package (the
mark is located in the lower right corner on the top side of the package).
4. The AT24C128/256 bearing the process letter “B” in the package (the mark is located in the lower right corner on the top
side of the package), guarantees 1 million write cycle endurance (1.8 – 3.6V).
Applicable over recommended operating range from TAI = 40°C to +85°C, VCC = +1.8V to +5.5V, CL = 100 pF (unless oth-
erwise noted). Test conditions are listed in Note 2.
Symbol Parameter
1.8-volt 2.5-volt 5.0-volt
UnitsMin Max Min Max Min Max
fSCL Clock Frequency, SCL 100 400 1000 kHz
tLOW Clock Pulse Width Low 4.7 1.3 0.4 µs
tHIGH Clock Pulse Width High 4.0 0.6 0.4 µs
tAA Clock Low to Data Out Valid 0.1 4.5 0.05 0.9 0.05 0.55 µs
tBUF
Time the bus must be free before a
new transmission can start(1) 4.7 1.3 0.5 µs
tHD.STA Start Hold Time 4.0 0.6 0.25 µs
tSU.STA Start Set-up Time 4.7 0.6 0.25 µs
tHD.DAT Data In Hold Time 0 0 0 µs
tSU.DAT Data In Set-up Time 200 100 100 ns
tRInputs Rise Time(1) 1.0 0.3 0.3 µs
tFInputs Fall Time(1) 300 300 100 ns
tSU.STO Stop Set-up Time 4.7 0.6 0.25 µs
tDH Data Out Hold Time 100 50 50 ns
tWR Write Cycle Time 20 or 5(3) 10 or 5(3) 10 or 5(3) ms
Endurance(1) 25°C, Page Mode 100k or 1,000,000(4) Write
Cycles
6AT24C128/256
0670O–SEEPR–2/05
AC Characteristics(5) – Extended Temperatures
Notes: 1. This parameter is characterized and is not 100% tested.
2. AC measurement conditions:
RL (connects to VCC): 1.3 k (2.5V, 5V), 10 k (1.8V)
Input pulse voltages: 0.3 VCC to 0.7 VCC
Input rise and fall times: 50 ns
Input and output timing reference voltages: 0.5 VCC
3. The Write Cycle Time of 5 ms only applies to the AT24C128/256 devices bearing the process letter “B” on the package (the
mark is located in the lower right corner on the top side of the package).
4. The AT24C128/256 bearing the process letter “B” in the package (the mark is located in the lower right corner on the top
side of the package), guarantees 1 million write cycle endurance (1.8 – 3.6V).
5. The AT24C128/256 bearing the process letter “B” on the package (the mark is located in the lower right corner on the top-
side of the package) are approved for operation in the extended temperature range.
Applicable over recommended operating range from TAE = 40°C to +125°C, VCC = +2.7V to +5.5V, CL = 100 pF (unless
otherwise noted). Test conditions are listed in Note 2.
Symbol Parameter
2.7-volt 5.0-volt
UnitsMin Max Min Max
fSCL Clock Frequency, SCL 400 1000 kHz
tLOW Clock Pulse Width Low 1.3 0.4 µs
tHIGH Clock Pulse Width High 0.6 0.4 µs
tAA Clock Low to Data Out Valid 0.05 0.9 0.05 0.55 µs
tBUF
Time the bus must be free before a new
transmission can start(1) 1.3 0.5 µs
tHD.STA Start Hold Time 0.6 0.25 µs
tSU.STA Start Set-up Time 0.6 0.25 µs
tHD.DAT Data In Hold Time 0 0 µs
tSU.DAT Data In Set-up Time 100 100 ns
tRInputs Rise Time(1) 0.3 0.3 µs
tFInputs Fall Time(1) 300 100 ns
tSU.STO Stop Set-up Time 0.6 0.25 µs
tDH Data Out Hold Time 50 50 ns
tWR Write Cycle Time 10 or 5(3) 10 or 5(3) ms
Endurance(1) 25°C, Page Mode 100k or 1,000,000(4) Write
Cycles
7
AT24C128/256
0670O–SEEPR–2/05
Device
Operation
CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external
device. Data on the SDA pin may change only during SCL low time periods (see Figure 4 on
page 8). Data changes during SCL high periods will indicate a start or stop condition as
defined below.
START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which
must precede any other command (see Figure 5 on page 9).
STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a
read sequence, the stop command will place the EEPROM in a standby power mode (see Fig-
ure 5 on page 9).
ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the
EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowl-
edge that it has received each word.
STANDBY MODE: The AT24C128/256 features a low power standby mode which is enabled:
a) upon power-up and b) after the receipt of the STOP bit and the completion of any internal
operations.
MEMORY RESET: After an interruption in protocol, power loss or system reset, any two-wire
part can be reset by following these steps: (a) Clock up to 9 cycles, (b) look for SDA high in
each cycle while SCL is high and then (c) create a start condition as SDA is high.
8AT24C128/256
0670O–SEEPR–2/05
Figure 2. Bus Timing (SCL: Serial Clock, SDA: Serial Data I/O)
Figure 3. Write Cycle Timing (SCL: Serial Clock, SDA: Serial Data I/O)
Note: 1. The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle.
Figure 4. Data Validity
twr
(1)
STOP
CONDITION
START
CONDITION
WORDn
ACK
8th BIT
SCL
SDA
9
AT24C128/256
0670O–SEEPR–2/05
Figure 5. Start and Stop Definition
Figure 6. Output Acknowledge
Device
Addressing
The 128K/256K EEPROM requires an 8-bit device address word following a start condition to
enable the chip for a read or write operation (see Figure 7 on page 11). The device address
word consists of a mandatory one, zero sequence for the first five most significant bits as
shown. This is common to all two-wire EEPROM devices.
The 128K/256K uses the two device address bits A1, A0 to allow as many as four devices on
the same bus. These bits must compare to their corresponding hardwired input pins. The A1
and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the
pins are allowed to float.
The eighth bit of the device address is the read/write operation select bit. A read operation is
initiated if this bit is high and a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will output a zero. If a compare is not
made, the device will return to a standby state.
DATA SECURITY: The AT24C128/256 has a hardware data protection scheme that allows the
user to write protect the whole memory when the WP pin is at VCC.
10 AT24C128/256
0670O–SEEPR–2/05
Write
Operations
BYTE WRITE: A write operation requires two 8-bit data word addresses following the device
address word and acknowledgment. Upon receipt of this address, the EEPROM will again
respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit
data word, the EEPROM will output a zero. The addressing device, such as a microcontroller,
then must terminate the write sequence with a stop condition. At this time the EEPROM enters
an internally-timed write cycle, tWR, to the nonvolatile memory. All inputs are disabled during
this write cycle and the EEPROM will not respond until the write is complete (see Figure 8 on
page 11).
PAG E WRITE : The 128K/256K EEPROM is capable of 64-byte page writes.
A page write is initiated the same way as a byte write, but the microcontroller does not send a
stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges
receipt of the first data word, the microcontroller can transmit up to 63 more data words. The
EEPROM will respond with a zero after each data word received. The microcontroller must ter-
minate the page write sequence with a stop condition (see Figure 9 on page 12).
The data word address lower 6 bits are internally incremented following the receipt of each
data word. The higher data word address bits are not incremented, retaining the memory page
row location. When the word address, internally generated, reaches the page boundary, the
following byte is placed at the beginning of the same page. If more than 64 data words are
transmitted to the EEPROM, the data word address will “roll over” and previous data will be
overwritten. The address “roll over” during write is from the last byte of the current page to the
first byte of the same page.
ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the
EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a
start condition followed by the device address word. The read/write bit is representative of the
operation desired. Only if the internal write cycle has completed will the EEPROM respond
with a zero, allowing the read or write sequence to continue.
11
AT24C128/256
0670O–SEEPR–2/05
Read
Operations
Read operations are initiated the same way as write operations with the exception that the
read/write select bit in the device address word is set to one. There are three read operations:
current address read, random address read and sequential read.
CURRENT ADDRESS READ: The internal data word address counter maintains the last
address accessed during the last read or write operation, incremented by one. This address
stays valid between operations as long as the chip power is maintained. The address “roll
over” during read is from the last byte of the last memory page, to the first byte of the first
page.
Once the device address with the read/write select bit set to one is clocked in and acknowl-
edged by the EEPROM, the current address data word is serially clocked out. The
microcontroller does not respond with an input zero but does generate a following stop condi-
tion (see Figure 10 on page 12).
RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data
word address. Once the device address word and data word address are clocked in and
acknowledged by the EEPROM, the microcontroller must generate another start condition.
The microcontroller now initiates a current address read by sending a device address with the
read/write select bit high. The EEPROM acknowledges the device address and serially clocks
out the data word. The microcontroller does not respond with a zero but does generate a fol-
lowing stop condition (see Figure 11 on page 12).
SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a ran-
dom address read. After the microcontroller receives a data word, it responds with an
acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment
the data word address and serially clock out sequential data words. When the memory
address limit is reached, the data word address will “roll over” and the sequential read will con-
tinue. The sequential read operation is terminated when the microcontroller does not respond
with a zero but does generate a following stop condition (see Figure 12 on page 12).
Figure 7. Device Address
Figure 8. Byte Write
12 AT24C128/256
0670O–SEEPR–2/05
Figure 9. Page Write
Notes: (* = DON’T CARE bit)
(† = DON’T CARE bit for the 128K)
Figure 10. Current Address Read
Figure 11. Random Read
Notes: (* = DON’T CARE bit)
(† = DON’T CARE bit for the 128K)
Figure 12. Sequential Read
13
AT24C128/256
0670O–SEEPR–2/05
Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics tables.
2. “U” and “Q” designates Green package + RoHS compliant
3. Available in waffle pack and wafer form; order as SL719 for wafer form. Bumped die available upon request. Please contact
Serial EEPROM Marketing
AT24C128 Ordering Information(1)
Ordering Code Package Operation Range
AT24C128-10PI-2.7
AT24C128N-10SI-2.7
AT24C128W-10SI-2.7
AT24C128-10TI-2.7
8P3
8S1
8S2
8A2
Industrial Temperature
(–40°C to 85°C)
AT24C128-10PI-1.8
AT24C128N-10SI-1.8
AT24C128W-10SI-1.8
AT24C128-10TI-1.8
8P3
8S1
8S2
8A2
Industrial Temperature
(–40°C to 85°C)
AT24C128-10PE-2.7
AT24C128N-10SE-2.7
8P3
8S1
Extended Temperature
(–40°C to 125°C)
AT24C128-10PQ-2.7(2)
AT24C128-10TQ-2.7(2)
AT24C128N-10SQ-2.7(2)
8P3
8A2
8S1
Lead-free/Halogen-free/
Extended Temperature
(–40°C to 125°C)
AT24C128-10PU-2.7(2)
AT24C128-10PU-1.8(2)
AT24C128N-10SU-2.7(2)
AT24C128N-10SU-1.8(2)
AT24C128-10TU-2.7(2)
AT24C128-10TU-1.8(2)
AT24C128U2-10UU-2.7(2)
AT24C128U2-10UU-1.8(2)
AT24C128Y1-10YU-2.7(2)
AT24C128Y1-10YU-1.8(2)
AT24C128Y4-10YU-2.7(2)
AT24C128Y4-10YU-1.8(2)
8P3
8P3
8S1
8S1
8A2
8A2
8U2-1
8U2-1
8Y1
8Y1
8Y4
8Y4
Lead-free/Halogen-free/
Industrial Temperature
(–40°C to 85°C)
AT24C128-W2.7-11(3)
AT24C128-W1.8-11(3)
Die Sale
Die Sale
Industrial Temperature
(–40°C to 85°C)
Package Type
8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC)
8S2 8-lead, 0.200" Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC)
8U2-1 8-ball, die Ball Grid Array Package (dBGA2)
8Y1 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP)
8Y4 8-lead, 6.00 mm x 4.90 mm Body, Dual Footprint, Non-leaded, Small Array Package (SAP)
8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP)
Options
2.7 Low-voltage (2.7V to 5.5V)
1.8 Low-voltage (1.8V to 3.6V)
14 AT24C128/256
0670O–SEEPR–2/05
Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics tables.
2. U” and “Q” designates Green Package + RoHS compliant
3. Available in waffle pack and wafer form; order as SL719 for wafer form. Bumped die available upon request. Please contact
Serial EEPROM Marketing
.
AT24C256 Ordering Information(1)
Ordering Code Package Operation Range
AT24C256-10PI-2.7
AT24C256N-10SI-2.7
AT24C256W-10SI-2.7
AT24C256-10TI-2.7
8P3
8S1
8S2
8A2
Industrial Temperature
(–40°C to 85°C)
AT24C256-10PI-1.8
AT24C256N-10SI-1.8
AT24C256W-10SI-1.8
AT24C256-10TI-1.8
8P3
8S1
8S2
8A2
Industrial Temperature
(–40°C to 85°C)
AT24C256-10PE-2.7
AT24C256N-10SE-2.7
8P3
8S1
Extended Temperature
(–40°C to 125°C)
AT24C256-10PQ-2.7(2)
AT24C256-10TQ-2.7(2)
AT24C256N-10SQ-2.7(2)
8P3
8A2
8S1
Lead-free/Halogen-free/
Extended Temperature
(–40°C to 125°C)
AT24C256-10PU-2.7(2)
AT24C256-10PU-1.8(2)
AT24C256N-10SU-2.7(2)
AT24C256N-10SU-1.8(2)
AT24C256-10TU-2.7(2)
AT24C256-10TU-1.8(2)
AT24C256U2-10UU-2.7(2)
AT24C256U2-10UU-1.8(2)
AT24C256Y4-10YU-2.7(2)
AT24C256Y4-10YU-1.8(2)
8P3
8P3
8S1
8S1
8A2
8A2
8U2-1
8U2-1
8Y4
8Y4
Lead-free/Halogen-free/
Industrial Temperature
(–40°C to 85°C)
AT24C256-W2.7-11(3)
AT24C256-W1.8-11(3)
Die Sale
Die Sale
Industrial Temperature
(–40°C to 85°C)
Package Type
8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC)
8S2 8-lead, 0.200" Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC)
8U2-1 8-ball, die Ball Grid Array Package (dBGA2)
8Y4 8-lead, 6.00 mm x 4.90 mm Body, Dual Footprint, Non-leaded, Small Array Package (SAP)
8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP)
Options
2.7 Low-voltage (2.7V to 5.5V)
1.8 Low-voltage (1.8V to 3.6V)
15
AT24C128/256
0670O–SEEPR–2/05
Packaging Information
8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131
TITLE DRAWING NO.
R
REV.
8P3, 8-lead, 0.300" Wide Body, Plastic Dual
In-line Package (PDIP)
01/09/02
8P3 B
D
D1
E
E1
e
L
b2
b
A2 A
1
N
eA
c
b3
4 PLCS
Top View
Side View
End View
COMMON DIMENSIONS
(Unit of Measure = inches)
SYMBOL MIN NOM MAX NOTE
Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information.
2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.
3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.
4. E and eA measured with the leads constrained to be perpendicular to datum.
5. Pointed or rounded lead tips are preferred to ease insertion.
6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).
A 0.210 2
A2 0.115 0.130 0.195
b 0.014 0.018 0.022 5
b2 0.045 0.060 0.070 6
b3 0.030 0.039 0.045 6
c 0.008 0.010 0.014
D 0.355 0.365 0.400 3
D1 0.005 3
E 0.300 0.310 0.325 4
E1 0.240 0.250 0.280 3
e 0.100 BSC
eA 0.300 BSC 4
L 0.115 0.130 0.150 2
16 AT24C128/256
0670O–SEEPR–2/05
8S1 – JEDEC SOIC
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TITLE DRAWING NO.
R
REV.
Note:
10/7/03
8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing
Small Outline (JEDEC SOIC) 8S1 B
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
A1 0.10 0.25
These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc.
A 1.35 1.75
b 0.31 0.51
C 0.17 0.25
D 4.80 5.00
E1 3.81 3.99
E 5.79 6.20
e 1.27 BSC
L 0.40 1.27
Top View
End View
Side View
eB
D
A
A1
N
E
1
C
E1
L
17
AT24C128/256
0670O–SEEPR–2/05
8S2 – EIAJ SOIC
2325 Orchard Parkway
San Jose, CA 95131
TITLE DRAWING NO.
R
REV.
8S2, 8-lead, 0.209" Body, Plastic Small
Outline Package (EIAJ)
10/7/03
8S2 C
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information.
2. Mismatch of the upper and lower dies and resin burrs are not included.
3. It is recommended that upper and lower cavities be equal. If they are different, the larger dimension shall be regarded.
4. Determines the true geometric position.
5. Values b and C apply to pb/Sn solder plated terminal. The standard thickness of the solder layer shall be 0.010 +0.010/0.005 mm.
A 1.70 2.16
A1 0.05 0.25
b 0.35 0.48 5
C 0.15 0.35 5
D 5.13 5.35
E1 5.18 5.40 2, 3
E 7.70 8.26
L 0.51 0.85
e 1.27 BSC 4
End View
Side View
eb
A
A1
D
E
N
1
C
E1
L
Top View
18 AT24C128/256
0670O–SEEPR–2/05
8U2-1 – dBGA2
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TITLE DRAWING NO.
R
REV.
PO8U2-1
A
6/24/03
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch,
Small Die Ball Grid Array Package (dBGA2)
A 0.81 0.91 1.00
A1 0.15 0.20 0.25
A2 0.40 0.45 0.50
b 0.25 0.30 0.35 2
D 2.35 BSC
E 3.73 BSC
e 0.75 BSC
e1 0.74 REF
d 0.75 BSC
d1 0.80 REF
1. This drawing is for general information only.
2. Dimension ‘b’ is measured at the maximum solder ball diameter.
d
A
Side View
Top View
Bottom View
8 Solder Balls
1
A
B
C
D
2
(e1)
e
A1 BALL PAD CORNER
(d1)
1. b
A1
A2
D
A1 BALL PAD CORNER
E
19
AT24C128/256
0670O–SEEPR–2/05
8Y1 – MAP
A 0.90
A1 0.00 0.05
D 4.70 4.90 5.10
E 2.80 3.00 3.20
D1 0.85 1.00 1.15
E1 0.85 1.00 1.15
b 0.25 0.30 0.35
e 0.65 TYP
L 0.50 0.60 0.70
PIN 1 INDEX AREA
D
E
A
A1 b
876
e
5
L
D1
E1
PIN 1 INDEX AREA
1234
A
Top View End View Bottom View
Side View
2325 Orchard Parkway
San Jose, CA 95131
TITLE DRAWING NO.
R
REV.
8Y1, 8-lead (4.90 x 3.00 mm Body) MSOP Array Package
(MAP) Y1 C
8Y1
2/28/03
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN NOM MAX
NOTE
20
AT24C128/256
0670O–SEEPR–2/05
8Y4 – SAP
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80817
TITLE DRAWING NO.
R
REV.
8Y4, 8-lead (6.00 x 4.90 mm Body) SOIC Array Package
(SAP) Y4 A
8Y4
5/24/04
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN NOM MAX NOTE
A 0.90
A1 0.00 0.05
D 5.80 6.00 6.20
E 4.70 4.90 5.10
D1 2.85 3.00 3.15
E1 2.85 3.00 3.15
b 0.35 0.40 0.45
e 1.27 TYP
e1 3.81 REF
L 0.50 0.60 0.70
A
EA1
b
PIN 1 INDEX AREA
D
A
PIN 1 ID
E1
D1
L
e
e1
21
AT24C128/256
0670O–SEEPR–2/05
8A2 – TSSOP
2325 Orchard Parkway
San Jose, CA 95131
TITLE DRAWING NO.
R
REV.
5/30/02
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
D 2.90 3.00 3.10 2, 5
E 6.40 BSC
E1 4.30 4.40 4.50 3, 5
A 1.20
A2 0.80 1.00 1.05
b 0.19 0.30 4
e 0.65 BSC
L 0.45 0.60 0.75
L1 1.00 REF
8A2, 8-lead, 4.4 mm Body, Plastic
Thin Shrink Small Outline Package (TSSOP)
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances,
datums, etc.
2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed
0.15 mm (0.006 in) per side.
3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm
(0.010 in) per side.
4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the
b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between
protrusion and adjacent lead is 0.07 mm.
5. Dimension D and E1 to be determined at Datum Plane H.
8A2 B
Side View
End View
Top View
A2
A
L
L1
D
123
E1
N
b
Pin 1 indicator
this corner
E
e
Printed on recycled paper.
0670O–SEEPR–2/05
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not
intended, authorized, or warranted for use as components in applications intended to support or sustain life.
Atmel Corporation Atmel Operations
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Literature Requests
www.atmel.com/literature
© Atmel Corporation 2005. All rights reserved. Atmel®, logo and combinations thereof, are registered trademarks, and Everywhere You AreSM
are trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.