E M C C o m p o n e n t s October 2013 3-terminal Filters, SMD Array For differential signal line (cellular band compatible) MEA-LD series MEA1210LD MEA1608LD MEA2010LD 1210[0504 inch]* 1608[0603 inch] 2010[0804 inch] * Dimensions Code JIS[EIA] (2/11) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20131004 / e9621_mea_differential.fm (3/11) E M C C o m p o n e n t s 3-terminal Filters, SMD Array Product compatible with RoHS directive Halogen-free Compatible with lead-free solders For differential signal line (cellular band compatible) Overview of the MEA-LD Series FEATURES LC filter with differential lines (D+ and D-) for high-density mounting. Compact with a low profile design. Can reduce radiation noise generated from differential signal lines (LVDS, MIPI, MDDI). Effective as a desensitization countermeasure in information transmission terminals such as smart phones. APPLICATION Noise removal for differential transmission lines (MIPI, etc.) of various mobile devices. PART NUMBER CONSTRUCTION MEA Series name 1210 LxWxT Dimensions (mm) 1210 1.2x1.0x0.5 1608 1.6x0.8x0.5 2010 2.0x1.0x0.5 LD 120 Product internal code LD Capacitance (pF) 120 12 170 17 T Packaging style Internal code T Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage Type temperature temperature C C MEA1210LD -40 to +85 -40 to +85 MEA1608LD -40 to +85 -40 to +85 MEA2010LD -40 to +85 -40 to +85 The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight pieces/reel 4,000 4,000 4,000 mg 3 3.5 5 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_differential.fm (4/11) E M C C o m p o n e n t s Overview of the MEA-LD Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s max. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_differential.fm (5/11) E M C C o m p o n e n t s MEA-LD series MEA1210LD Type SHAPE & DIMENSIONS GND CH1 CH2 1.00.15 GND 0.1min. 0.250.1 1.20.15 0.1min. 0.50.1 0.650.05 Dimensions in mm 0.15min. 0.350.1 RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 0.65 0.5 0.3 GND GND CH2 0.6 0.25 CH1 0.9 1.8 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_differential.fm (6/11) E M C C o m p o n e n t s MEA-LD series MEA1210LD Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Capacitance (pF) 22 17 12 Cutoff frequency (MHz)typ. 250(Sdd) 310(Sdd) 410(Sdd) Rated voltage (V)max. 6.3 6.3 6.3 Measurement equipment Measurement item Product No. Capacitance 4294A Frequency characteristics N5230C Equivalent measurement equipment may be used. Rated current (mA)max. 100 100 100 Part No. MEA1210LD220T MEA1210LD170T MEA1210LD120T Manufacturer Agilent Technologies Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 10 220 Sdd Insertion loss (dB) 20 170 Scc 30 170 Sdd 40 120 Sdd 50 220 Scc 120 Scc 60 70 10 100 1000 10000 Frequency (MHz) Measurement equipment Product No. Manufacturer N5230C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_differential.fm (7/11) E M C C o m p o n e n t s MEA-LD series MEA1608LD Type 0.20.1 CH1 CH2 CH3 CH4 GND GND 0.40.05 0.40.05 0.50.1 0.40.05 0.80.1 1.60.1 0.05min. SHAPE & DIMENSIONS 0.15min. 0.20.1 Dimensions in mm RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 2.0 CH1 CH2 CH3 CH4 GND GND 0.5 0.35 0.15 0.15 to 0.2 0.025 0.2 to 0.25 0.4 0.04 0.35 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_differential.fm (8/11) E M C C o m p o n e n t s MEA-LD series MEA1608LD Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Capacitance (pF) 22 15 10 Cutoff frequency (MHz)typ. 270(Sdd) 380(Sdd) 500(Sdd) Rated voltage (V)max. 6.3 6.3 6.3 Measurement equipment Measurement item Product No. Capacitance 4294A Frequency characteristics N5230C Equivalent measurement equipment may be used. Rated current (mA)max. 50 50 50 Part No. MEA1608LD220T MEA1608LD150T MEA1608LD100T Manufacturer Agilent Technologies Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 Insertion loss (dB) 10 20 150 Scc 30 100 Sdd 40 220 Scc 100 Scc 150 Sdd 50 60 10 220 Sdd 100 1000 10000 Frequency (MHz) Measurement equipment Product No. Manufacturer N5230C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_differential.fm (9/11) E M C C o m p o n e n t s MEA-LD series MEA2010LD Type 2.00.15 0.250.1 CH1 CH2 CH3 CH4 GND GND 0.50.1 0.50.1 0.50.1 0.50.1 1.00.15 0.10min. SHAPE & DIMENSIONS 0.15min. 0.250.1 Dimensions in mm RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 2.80 1.60 0.25 CH1 0.50 0.25 CH4 GND 1.80 0.60 GND CH2 CH3 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_differential.fm (10/11) E M C C o m p o n e n t s MEA-LD series MEA2010LD Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Capacitance (pF) 22 17 12 Cutoff frequency (MHz)typ. 240(Sdd) 330(Sdd) 430(Sdd) Rated voltage (V)max. 6.3 6.3 6.3 Measurement equipment Measurement item Product No. Capacitance 4294A Frequency characteristics N5230C Equivalent measurement equipment may be used. Rated current (mA)max. 100 100 100 Part No. MEA2010LD220T MEA2010LD170T MEA2010LD120T Manufacturer Agilent Technologies Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 Insertion loss (dB) 10 20 30 220 Scc 150 Sdd 40 220 Sdd 170 Scc 120 Scc 50 60 10 100 1000 100 Sdd 10000 Frequency (MHz) Measurement equipment Product No. Manufacturer N5230C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_differential.fm (11/11) E M C C o m p o n e n t s MEA-LD series Packaging style REEL DIMENSIONS o60min. 2.00.5 1.0 8.4 +2.0 -0.0 o130.2 o210.8 14.4max. o1802.0 Dimensions in mm TAPE DIMENSIONS 1.750.1 t B 3.50.05 4.00.1 4.00.1 A MEA1608LD 8.00.3 2.00.05 1.5 +0.1 0 MEA1210LD, MEA2010LD K K Dimensions in mm Type MEA1210LD MEA1608LD MEA2010LD A 1.200.05 1.000.10 1.150.05 160min. Taping B 1.450.05 1.800.10 2.150.05 K 0.73max. 1.0max. 1.0max. t -- 0.250.05 -- 200min. 300min. Drawing direction MEA1210LD MEA1608LD MEA2010LD Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131004 / e9621_mea_differential.fm