Instruction Sheet PRO- CRIMPER III Hand Crimping Tool Assembly 58448- 2 With Die Assembly 58448- 3 408-- 9357 24 AUG 09 Rev D PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-- use, production operations is available. Locator Assembly Front of Tool (Locator Side) Stationary Jaw Pivot Pin PRO-- CRIMPER III Hand Crimping Tool Frame 354940-- 1 (408-- 9930) Die Assembly Moving Jaw Back of Tool (Wire Side) Ratchet Adjustment Wheel The PRO-- CRIMPER III Hand Crimping Tool is a "Commercial" grade tool and is designed primarily for field installation, repair, maintenance work, or prototyping in industrial, commercial, or institutional applications. Product crimped with this tool will meet the crimp height requirement for hand tools in the appropriate 114 series specification, but may not comply with other feature parameters of the specification. Tyco Electronics offers a variety of tools to satisfy your performance requirements. For additional information, contact the Tooling Assistance Center at 1-- 800-- 722-- 1111. TE Die Assembly 58448 3 58448--3 Stationary Handle Movable Handle Wire Locator Assembly{ Product Family} Size Range (AWG) Insulation Diameter (Max) (mm [in.]) 28--24 1.02 [.040] 1214310 1 1214310--1 AMPLIMITE* HDP--20 Connector Crimp Snap--In Contacts with Insulation Support 24--20 1.52 [.060] Strip Length (mm [in.]) 2 54 [.100] 2.54 [ 100] { Supplied with die assembly. Also available separately. } Contact the Tooling Assistance Center or Product Information at the numbers listed below for specific contact part numbers. Figure 1 1. INTRODUCTION 2. DESCRIPTION PRO--CRIMPER III Hand Crimping Tool Assembly 58448--2 consists of Die Assembly 58448--3 and PRO--CRIMPER III Hand Crimping Tool Frame 354940--1. The die assembly consists of crimping dies and a locator assembly. The tool features a tool frame with a stationary jaw and handle, moving jaw, moving handle, and adjustable ratchet that ensures full contact crimping. The tool frame holds a die assembly with two crimping chambers. See Figure 1. Read these instructions thoroughly before crimping any contacts. The die assembly features a wire anvil, insulation anvil, wire crimper, and insulation crimper. NOTE i Dimensions in this instruction sheet are in metric units [with U.S. customary units in brackets]. Figures are not drawn to scale. Reasons for reissue of this instruction sheet are provided in Section 10, REVISION SUMMARY. Die retaining pins and die retaining screws are used to position and secure the dies in the tool frame. Attached to the outside of the frame is a locator assembly, which contains a locator and contact retainer. A nut is used on the upper die retaining screw to hold the locator assembly in place. TOOLING ASSISTANCE CENTER 1-- 800-- 722-- 1111 E2009 Tyco Electronics Corporation, Harrisburg, PA PRODUCT INFORMATION 1-- 800-- 522-- 6752 All International Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.tycoelectronics.com 1 of 5 LOC B 408- 9357 PRO- CRIMPER III Hand Crimping Tool Assembly 58448- 2 Locator Assembly Nut Tool Frame Locator Chamfered Edge Long Die Retaining Pins (Supplied with Locator Assembly) Insulation Crimper Short Die Retaining Pins Wire Crimper Offset Wire Anvil Insulation Anvil Chamfered Edge Short Die Retaining Screw Long Die Retaining Screw Figure 2 3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY AND LOCATOR ASSEMBLY (Figure 2) 1. Open the tool handles, and remove the two die retaining screws from the tool jaws. 2. Place the wire anvil and insulation anvil so that the chamfered sides and marked surfaces face outward, when mounted in the moving jaw of the tool frame. 3. Insert the two short die retaining pins through the tool frame and into the anvils. 4. Insert the short die retaining screw through the jaw and through both anvil dies, and tighten the screw just enough to hold the dies in place. Do not tighten the screw completely at this time. 5. Place the wire crimper and insulation crimper so that their chamfered sides and their marked surfaces face outward, when mounted in the stationary jaw of the tool frame. 6. Insert the two long die retaining pins (supplied with the locator assembly) through the tool frame and into the crimpers. 7. Insert the long die retaining screw through the jaw and through both crimper dies, and tighten the screw just enough to hold the dies in place. Do not tighten the screw completely at this time. 8. Carefully close the tool handles, making sure that the anvils and crimpers align properly. Continue closing the tool handles until the ratchet in the tool frame has engaged sufficiently to hold 2 of 5 the anvils and crimpers in place, then tighten both die retaining screws. 9. Remove the pin from the center hole in the locator assembly. Place the locator assembly over the end of the long die retaining screw and long die retaining pins. Position the locator assembly against the side of the tool jaw. 10. Place the nut onto the end of the long screw and tighten the nut enough to hold the locator assembly in place, while still allowing the locator to slide up and down. 11. To disassemble, close the tool handles until the ratchet releases, remove the nut, the locator assembly, the two die retaining screws, and the four die retaining pins, and slide the anvils and crimpers out of the tool jaws. 4. CRIMPING PROCEDURE NOTE i This tool is provided with a crimp adjustment feature. Initially, the crimp height should be verified as specified in Section 5, CRIMP HEIGHT INSPECTION, and Section 6, RATCHET (Crimp Height) ADJUSTMENT, before using the tool to crimp desired contacts. Refer to Figure 1, and select wire of the specified size and insulation diameter. Strip the wire to the length indicated, taking care not to nick or cut wire strands. Select an applicable contact and identify the appropriate crimping chamber according to the wire size markings on the tool. Refer to Figure 3, and proceed as follows: Tyco Electronics Corporation Rev D 408- 9357 PRO- CRIMPER III Hand Crimping Tool Assembly 58448- 2 1. Hold the tool so that the front (locator side) is facing you. Squeeze tool handles together and allow them to open fully. NOTE i 2. Insert the contact--mating end first--into the hole in the locator which corresponds with the appropriate crimping chamber. Make sure that the open "U" of the wire barrel and insulation barrel face the stationary jaw. CAUTION ! 7. Check the contact crimp height as described in Section 5, CRIMP HEIGHT INSPECTION. If necessary, adjust the crimp height as described in Section 6, CRIMP HEIGHT ADJUSTMENT. Do NOT attempt to close the tool handles when locator contact retainer is between the dies. Damage to the tool jaws or locator may result. 5. CRIMP HEIGHT INSPECTION Crimp height inspection is performed through the use of a micrometer with a modified anvil, commonly referred to as a crimp--height comparator. Tyco Electronics does not manufacture or market crimp--height comparators. Detailed information on obtaining and using crimp--height comparators can be found in instruction sheet 408--7424. 3. Slide the locator contact retainer out from between the dies (spring tension will pull the locator down). Make sure that the wire stop enters the contact wire stop slot between the wire barrel and contact shoulder. Release contact retainer. CAUTION ! Make sure that both sides of the contact insulation barrel are started evenly into the crimping chamber. Do NOT attempt to crimp an improperly positioned contact. Proceed as follows: 1. Refer to Figure 4 and select the maximum size wire for the crimping chamber. 4. Hold the contact in position, and squeeze the tool handles together until ratchet engages sufficiently to hold the contact in position. Do NOT deform insulation barrel or wire barrel. 2. Refer to Section 3, CRIMPING PROCEDURE, and crimp the contact accordingly. 5. Insert stripped wire into contact insulation and wire barrels until it is butted against the wire stop, as shown in Figure 3. 3. Using a crimp height comparator, measure the wire barrel crimp height as shown in Figure 4. If the crimp height conforms to that shown, the tool is considered dimensionally correct. If not, the tool must be adjusted. Refer to Section 6, CRIMP HEIGHT ADJUSTMENT. 6. Holding the wire in place, squeeze tool handles together until ratchet releases. Allow tool handles to open and remove crimped contact. Locator The crimped contact may stick in the crimping area, but can be removed by pushing downward on the top of the locator (see Figure 3). Back of Tool (Wire Side) Contact Retainer Tool Stationary Jaw Wire Wire Strip Length Tool Wire Size Markings Locator in Contact Wire Stop Slot Wire Inserted to Locator Wire Stop Figure 3 Rev D Tyco Electronics Corporation 3 of 5 408- 9357 PRO- CRIMPER III Hand Crimping Tool Assembly 58448- 2 7. MAINTENANCE Position Point on Center of Wire Barrel Opposite Seam Ensure that the tool and dies are clean by wiping them with a clean, soft cloth. Remove any debris with a clean, soft brush. Do not use objects that could damage the tool. When not in use, keep handles closed to prevent objects from becoming lodged in the crimping dies, and store in a clean, dry area. Spindle Crimp Height Modified Anvil Wire Size (AWG) (Max) Crimp Height Dimension +0.05 mm [+.002 in.] 24 0.724 [.0285] 20 0.749 [.0295] Figure 4 6. RATCHET (Crimp Height) ADJUSTMENT (Figure 5) 1. Remove the lockscrew from the ratchet adjustment wheel. 8. VISUAL INSPECTION The crimping dies should be inspected on a regular basis to ensure that they have not become worn or damaged. Inspect the crimping chambers for flattened, chipped, worn, or broken areas. If damage or abnormal wear is evident, the tool must be replaced. See Section 9, REPLACEMENT. 9. REPLACEMENT Customer--replaceable parts are shown in Figure 1. 2. With a screwdriver, adjust the ratchet wheel from the locator side of the tool. 3. Observe the ratchet adjustment wheel. If a tighter crimp is required, rotate the adjustment wheel counterclockwise to a higher--numbered setting. If a looser crimp is required, rotate the adjustment wheel clockwise to a lower--numbered setting. 4. Re--assemble the lockscrew. 5. Make a sample crimp and measure the crimp height. 6. If the dimension is unacceptable, continue to adjust the ratchet, and again measure a sample crimp. Available separately, PRO--CRIMPER III Hand Crimping Tool Repair Kit 679221--1 includes a replacement nut and a variety of pins, rings, screws, and springs. If the dies are damaged or worn excessively, they must be replaced. Order repair kit and replaceable parts through your Tyco Electronics representative, or call 1--800--526--5142, or send a facsimile of your purchase order to 717--986--7605, or write to: CUSTOMER SERVICE (38--35) TYCO ELECTRONICS PO BOX 3608 HARRISBURG PA 17105--3608 10. REVISION SUMMARY Revisions to this instruction sheet include: Screwdriver S Changed PRO--CRIMPER II Hand Tool to PRO--CRIMPER III Hand Tool; S Modified Crimp Height Inspection information; S Added the TE logo; and S Added alternate tools on back page. Ratchet Adjustment Wheel Lockscrew (Typ) Figure 5 4 of 5 Tyco Electronics Corporation Rev D 408- 9357 PRO- CRIMPER III Hand Crimping Tool Assembly 58448- 2 Die Assembly 58448- 3 Can Be Used In the Following Tools: PRO- CRIMPER III Hand Tool 354940- 1 (Instruction Sheet 408- 9930) SDE PEW- 12 Hand Tool 9- 1478240- 0 (Instruction Sheet 408- 8851) SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) 626 Adapter 679304- 1 (Instruction Sheet 408- 4070) Battery Tool (Shouldered Die) 1725837- 1, - 2 (Customer Manual 409- 10053) Rev D Battery Tool (Pin Die) 1213890- 1, - 2 (Customer Manual 409- 10065) Tyco Electronics Corporation 5 of 5