Optical Fiber Cords An Example of the Constructions of Optical Fiber Cords An optical fiber cords is constructed by covering the optical fiber core with the buffer around the optical fiber being covered with the primary coat as illustrated below. Also, this optical fiber core is provided with Kevler fiber reinforced plastic (a tensile strength material) being covered with the jacket around. Core Cladding Optical fiber Primary coat Buffer Kebler (A tensile strength material) Jacket Optical fiber cord Sort of Optical Fibers An optical fiber consists of a core and a cladding. Light passes through the core while it is being reflected by the cladding as illustrated below. Cladding Core r mete g dia din Clad Co re d iam ete r Cladding Core and cladding of optical fiber The optical fiber modes are shown in the following figures. Item Number Multi Mode (MM) Single Mode (SM) Graded Index (G ) Step Index (S ) Sketch Cladding Core Cladding Core Cladding Wavelengths commonly used as light source for silica optical fiber are 0.85, 1.31, or 1.55 m. Categorized by mode and wavelength, the optical fiber can be shown as follows. Name 1.31m Single mode optical fiber Mode Core Diameter / Cladding Diameter [m] Wavelength [m] 10/125 1.31 Yellow 8/125 1.55 Orange Typical Jacket Color Single mode 1.55m Single mode optical fiber Graded index optical fiber Multi mode Graded index 50/125 1.31 Blue Step index optical fiber Multi mode Step index 100/140 0.85 Uncertain Core Sort of the Constructions of Optical Fiber Cords The secondary sheath diameters are sorted into o2mm and o2.8mm. Certain cores are not covered with the secondary sheath. Sort of the constructions of optical fiber cords Name Outside Diameter [mm] o2 optical fiber cord o2 o2.8 optical fiber cord o2.8 o0.9 buffered fiber o0.9 Ultraviolet hardened buffered fiber o0.4, o0.25 Primary Coat Buffer X Nylon resin etc. ---- Ultraviolet hardened resin Jacket X ---X : Correspond Optical Fiber Connectors Optical fibers can be connected to each other by the permanent connection method or removable connector connection method. The optical fiber connection is subjected to various connection loss factors, such as the axial misalignment of fibers, angular deviations, space deviations, incomplete end faces, etc. Optical fiber connectors are required to have highly precise sizes to coincide the optical fiber cores with each other accurately. Optical fiber connectors are indispensable for connecting between optical fibers and various devices as the components of optical communication systems. Major polishing of optical fiber connectors The standard values of the insertion loss and return loss depend upon the polishing and mode. (Note: Indicates the standard values at one end) Specifications No. Drawing Polishing shape Insertion loss Single mode Multi mode Graded Index Return loss Single mode Multi mode Graded Index ----- ----- Optical fiber 1 Flat polishing 1.0dB or less 0.6dB or less Ferrule Optical fiber 2 PC polishing (R20 convex sphere polishing) 0.5dB or less 0.3dB or less 22dB or more 22dB or more Ferrule Optical fiber 3 AdPC polishing (Advanced PC polishing) 0.5dB or less 0.3dB or less 40dB or more ----- Ferrule Optical fiber 4 Angled polishing ----- ----- ----- ----- 0.5dB or less ----- 57dB or more ----- Ferrule Optical fiber 5 Angled PC polishing Ferrule Major Specifications Test items No. Requirements (See Note #1, #2) Test method (See Note #2) Refer to JIS C 5961 : 2005 Insertion Loss Plug Single mode AdPC, PC polishing: 0.5dB or less Multi mode Graded index PC polishing: 0.3dB or less 7.1 : 0.3dB or less Adaptor 2 Return Loss AdPC polishing : 40dB or more PC polishing : 22dB or more 3 Repetitive Operation (Repetitive mounting and removal) 1 Optical performance 4 Mechanical performance 5 Resistance to Vibration Resistance to Shock 6 Change of Temperature 7 Resistance to damp heat (Cyclic) Environmental performance 7.2 Shall satisfy the requirements about the Insertion Loss and Return Loss after test. 8.3 Operation times : 500times No mechanical damage 8.1 Frequency : 10~55Hz Single amplitude : 0.75mm Cycle times : 24 Shall satisfy the requirements about the Insertion Loss and Return Loss after test. Direction : 3directions No mechanical damage 8.2 Peak acceleration : 981m/s2 Direction : 3directions 5times each 9.2 Temperature : -25~70C Duration : 1.5H/cyc 9.4 Temperature : -10~65C Humidity : 933% Shall satisfy the requirements about Duration : 24H/cyc the Insertion Loss and Return Loss after test. Cycle times: 10 No mechanical damage 8 Resistance to Dry Heat 9.5 Temperature : 85C Duration : 240H 9 Resistance to Cold 9.6 Temperature : -25C Duration : 240H Note 1: The Insertion Loss and Return Loss depend upon the modes and polishing methods. Note 2: Certain products don't always conform to these requirements or testing methods. Note 3: Certain products may also be tested by test items other than specified above. Measurement of Insertion Loss and Return Loss Insertion Loss Insertion Loss [dB] = -10Log P1 P0 Adaptor Test Sample P0 LD Optical Source =1.31m P1 Optical Power Meter Master Connector Plug Optical Fiber Cord with Connector Master Adaptor LED Optical Source =1.31m Mode Scrambler P0 P1 Optical Power Meter Master Connector Plug Test Sample SM, 1.55SM Optical Fiber Cord with Connector Master Adaptor LD Optical Source =1.31m or =1.55m P0 P1 Optical Power Meter Master Connector Plug Test Sample Connector Convertor Master Adaptor LED Optical Source =1.31m P0 Mode Scrambler Optical Power Meter P1 Master Connector Plug Test Sample Master Connector Plug SM Connector Convertor Master Adaptor LD Optical Source =1.31m or =1.55m P0 Optical Power Meter P1 Master Connector Plug Test Sample Master Connector Plug Return Loss Return Loss [dB] = -10Log P1 P0 Optical Fiber Cord with Connector Referance Cord Evaporated Gold LD Optical Source =1.31m or =1.55m P0 Coupler Master Adaptor P1 Optical Power Meter Master Connector Plug Test Sample Optical Fixed Attenuator or Connector Convertor Matching Oil Referance Cord Evaporated Gold LD Optical Source =1.31m or =1.55m P0 Coupler Master Adaptor P1 Optical Power Meter Master Connector Plug Matching Oil Test Sample Attenuation of Optical Fixed Attenuator Attenuation [dB] = -10Log P1 P0 Optical Attenuator Master Adaptor LED Optical Source =1.31m P0 Mode Scrambler Optical Power Meter P1 Master Connector Plug Test Sample Master Connector Plug SM Optical Fixed Attenuator Master Adaptor LD Optical Source =1.31m or =1.55m P0 Optical Power Meter P1 Master Connector Plug Test Sample Master Connector Plug Optical fiber connector FC-type Optical Fiber Connector LGC-100 series FC-type JIS C 5970 F01 type Each FC-type plug consists of a plug and adaptor. It is a connector of the screw lock type. Plug (with ferrule) Adaptor Receptacle Terminator Specifications Items Requirements Single Mode Insertion Loss SMT Press-in 0.2dB 0.1dB Multi Mode Graded Index : 0.3dB or less Return Loss Through hole Actual Value (Average) : 0.5dB or less IDC Single Mode (AdPC polishing) : 40dB or more 50dB Single Mode (PC polishing) : 22dB or more 30dB Multi Mode Graded Index (PC polishing) : 22dB or more 29dB Wire Soldering Crimping wrapping Others Optical fiber connector FC-type Plug LGC-100 series FC-type JIS C 5970 F01 type Plug Each FC-type plug consists of a plug housing and a ferrule. FC-type Plug Housing Applicable to optical cords having on outside diameter of o2 or o2.8mm and o0.9mm. For boot colors, please contact us for those other than specified below. A cap is attached. Applicable to Optical Cords having on Outside Diameter of o2 or o2.8mm Applicable Outside Diameter of Optical fiber cords LGC-PH2+R o2mm LGC-PH+R o2.8mm Note (Boot color : Black) M80.75P Item Number o9.8 2.1 unit(mm) 38 REF. Ferrule is excluded. Applicable to Optical Cords having on Outside Diameter of o0.9mm (Buffered Fiber) Applicable Outside Diameter of Optical fiber cords For PC polishing LGC-PH3B+R LGC-PH3L+R Note o0.9mm (Boot color : Blue) For AdPC polishing (Boot color : Mauve) For AdPC polishing (Boot color : Yellow) LGC-PH3+R M80.75P Item Number o9.8 2.1 unit(mm) 27 REF. Ferrule is excluded. Crimp Assembly type This type is assembled by caulking the kevler and sheath of the optical fiber cord to the plug housing in the same way as in SC-type plug. LGC-PH5L+R o2mm Note For PC polishing (Boot color : Blue) For AdPC polishing (Boot color : Mauve) M80.75P LGC-PH5B+R Applicable Outside Diameter of Optical fiber cords 2.1 unit(mm) 53.6 REF. o9.8 Item Number Ferrule is excluded. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Ferrule FC-type/SC-type/DS-type Ferrule Zirconia Ferrule (for Single Mode/Multi Mode Graded Index) Inside Diameter of the ferrule [mm] LGC-PFS5B4 o0.125 LGC-PFS5.5B4 o0.1255 LGC-PFS6B4 o0.126 LGC-PFS7B4 o0.127 LGC-PFS8B4 o0.128 unit(mm) o2.4990.0005 3.1 16 7.95 1.8 1.5 o4 .6 o0.124 The ferrules are provided with a rotation stop key at 4 positions. o1.1 o2 o0.123 LGC-PFS4B4 Note Inside Diameter of the ferrule LGC-PFS3B4 Outside Diameter of the ferrule [mm] Outside Diameter of the ferrule Item Number Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector FC-type Adaptor LGC-100 series FC-type JIS C 5970 F01 type Adaptor Phosphor-Bronze-Alignment-Sleeve Adaptor Phosphor Bronze 15 9.5 4 M80.75P 2.4 15 FC-AP 9.5 LGC-A101+R unit(mm) Material of Alignment Sleeve HONDA Item Number 2-o2.2 unit(mm) Mounting Hole Size 9.50.1 9.50.1 o9.2 2-o2.2 or 2-M2 Zirconia-Alignment-Sleeve Adaptor This product is an improved adapter for zirconia-alignment. unit(mm) Zirconia 9.5 4 2.4 15 M80.75P 15 FC-AP HONDA LGC-A114+R Material of Alignment Sleeve 9.5 Item Number 2-o2.2 The mounting hole size is equal to that of LGC-A101+R. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector FC-type Receptacle/FC-type Cap for Adaptor LGC-100 series FC-type JIS C 5970 F01 type Receptacle/Cap FC-type Receptacle Material of Alignment Sleeve Item Number unit(mm) oe15 9.5 Stainless steel LGC-R101+R 4-o2.2 9.5 HONDA FC-R M80.75P 0.5 3 9 5.5 2.4 o7 unit(mm) Mounting Hole Size 9.50.1 9.50.1 o7.2 4-o2.2 or 4-M2 FC-type Cap for Adaptor Item Number unit(mm) LGC-C1+R 13 50 REF. o3.5 o12 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector FC-type Terminator LGC-100 series FC-type JIS C 5970 F01 type Terminator The terminator is provided to prevent the reflected light at the end face of the optical connector. FC-type is sub-devided into the plug type and adaptor type. FC-Plug-type Terminator Item Number LGC-PTA101+R Note Return Loss : 40dB or more 22.3 REF. o9.8 2.1 o6.9 M80.75P unit(mm) FC-Adaptor-type Terminator Item Number Note Return Loss : 40dB or more unit(mm) 2.4 17.3 Others Wire wrapping Crimping Soldering o8.8 M80.75P LGC-ATA101+R IDC Press-in SMT Through hole Optical fiber connector SC-type Optical Fiber Connector LGC-300 series SC-type JIS C 5973 F04 type Each SC-type optical connector consists of a plug and an adaptor. High density SC2-type optical fiber connectors are also available. SC-type Plug SC-type Adaptor SC2-type Plug SC2-type Adaptor SC-type Terminator SC-type Receptacle Specifications Items Requirements Insertion Loss Return Loss Through hole SMT Press-in Single Mode Actual Value (Average) 0.2dB : 0.5dB or less Multi Mode Graded Index : 0.3dB or less 0.1dB Single Mode (AdPC polishing) : 40dB or more 50dB Single Mode (PC polishing) : 22dB or more 30dB Multi Mode Graded Index (PC polishing) : 22dB or more 29dB IDC Wire Soldering Crimping wrapping Others Optical fiber connector SC-type Plug LGC-300 series SC-type JIS C 5973 F04 type Plug Each SC-type plug consists of a plug housing and a ferrule. Plug housings are sorted into SC-type simplex plug housing, vertical (H type) duplex plug housing, and horizontal type (F type) duplex plug housing. The ferrule (Refer to page L-10) employed for FC-type connector plug is also applicable to these plug housings. SC-type Simplex Plug Housing (SC-PH type Plug Housing) Applicable to Optical Cords having on Outside Diameter of o2 or o2.8mm (The weight reduction has been achieved by using a resin stopper.) Item Number LGC-PH353MK+R LGC-PH353MKL+R LGC-PH354MK+R LGC-PH354MKL+R Applicable Outside Diameter of Optical fiber cords o2mm o2.8mm Note For PC polishing (Boot color : Blue) For AdPC polishing (Boot color : Mauve) For PC polishing (Boot color : Blue) For AdPC polishing (Boot color : Mauve) 55 REF. unit(mm) 9 1.8 7.4 Ferrule is excluded. Applicable to Optical Cords having on Outside Diameter of o0.9mm (The weight reduction has been achieved by using a resin stopper.) Item Number Applicable Outside Diameter of Optical fiber cords LGC-PH305M LGC-PH305MB o0.9mm Note For PC polishing (Boot color : Yellow) For PC polishing (Boot color : Blue) For AdPC polishing (Boot color : Mauve) LGC-PH305MBL 38 REF. unit(mm) 9 1.8 7.4 Ferrule is excluded. Applicable to Optical Cords having on Outside Diameter of o1.1mm o1.1mm Note For AdPC polishing (Boot color : Mauve) 55 REF. 7.4 1.8 LGC-PH358H+R Applicable Outside Diameter of Optical fiber cords 9 Item Number Ferrule is excluded. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector SC-type Plug LGC-300 series SC-type JIS C 5973 F04 type Plug Vertical (H type) Duplex Plug Housing (SCH-2PH type Plug Housing) Applicable to Optical Cords having on Outside Diameter of o2 or o2.8mm (The weight reduction has been achieved by using a resin stopper.) Applicable Outside Diameter of Optical fiber cords Item Number LGC-H2PH353MK[ ]SHBB+R For PC polishing o2mm LGC-H2PH353MK[ ]SHLL+R LGC-H2PH354MK[ ]SHBB+R (Boot color : Blue) For AdPC polishing (Boot color : Mauve) For PC polishing o2.8mm LGC-H2PH354MK[ ]SHLL+R Note (Boot color : Blue) For AdPC polishing (Boot color : Mauve) [ ] is filled with the type of guide key. (See the following table) unit(mm) A 55 REF. 15.9 8.5 B 1.8 Type of Guide key (indication) 9 Ferrule is excluded. Type of Guide Key for Vertical Duplex Plugs Type of Guide Key (Indication) A (Position of misinsertion Prevention key) B (Width of misinsertion Prevention key) 3.00 2.65 A B 1.30 2.65 P 2.15 0.95 R 2.15 4.35 Type of Guide Key for Connectable Vertical Duplex Adaptors A B P X X X X X X X An Example of Part No. Specifications LGC-H2PH353MKPSHLL+R Through hole SMT Press-in IDC Outside diameter of applicable optical fiber cords o2mm Type of Guide Key P Size A 2.15mm Size B 0.95mm Boot color Mauve Wire Soldering Crimping wrapping Others X X X : Correspond Reference R Optical fiber connector SC-type Plug LGC-300 series SC-type JIS C 5973 F04 type Plug Horizontal (F type) Duplex Plug Housing (SCF-2PH type Plug Housing) Applicable to Optical Cords having on Outside Diameter of o2 or o2.8mm (The weight reduction has been achieved by using a resin stopper.) Applicable Outside Diameter of Optical fiber cords Item Number LGC-F2PH353MK[ ]SHBB+R For PC polishing o2mm LGC-F2PH353MK[ ]SHLL+R LGC-F2PH354MK[ ]SHBB+R (Boot color : Blue) For AdPC polishing (Boot color : Mauve) For PC polishing o2.8mm LGC-F2PH354MK[ ]SHLL+R Note (Boot color : Blue) For AdPC polishing (Boot color : Mauve) [ ] is filled with the type of guide key. (See the following table) unit(mm) Type of Guide key (indication) 7.8 7.4 1.8 R 21.7 12.7 A B 55 REF. Ferrule is excluded. Type of Guide Key for Horizontal Duplex Plugs Type of Guide Key (Indication) A (Position of misinsertion Prevention key) B (Width of misinsertion Prevention key) A 0.95 1.90 B 1.90 0.95 P 1.90 1.90 R 0.95 0.95 Type of Guide Key for Connectable Horizontal Duplex Adaptors A B P R X X X X X X X X X X : Correspond Reference An Example of Part No. LGC-F2PH353MKPSHLL+R Specifications Outside diameter of applicable optical fiber cords o2mm Type of Guide Key P Size A 1.90mm Size B 1.90mm Boot color Mauve Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Conversion Adaptor/SC-type Receptacle LGC-300 series SC-type JIS C 5973 F04 type Conversion adaptor/Receptacle SC-FC type Conversion Adaptor (SC-FC-A type Conversion Adaptor) An SC-type plug and an FC-type plug are connectable to each other. Item Number Material of Alignment Sleeve LGC-A301/A101+R Note Phosphor bronze Zirconia LGC-A302/A104+R unit(mm) 13.4 21.2 3.5 4 2. 9 12.8 2 12.2 M80.75P 9 7.4 oe1 5 2-o2.2 The mounting hole size is equal to that of LGC-A101+R. SC-type Receptacle (SC-R type Receptacle) Use these recptacles by mounting them to measuring instrument, etc. Material of Alignment Sleeve Stainless steel LGC-R301+R Materials of Housing Note Zinc alloys die casting unit(mm) oe1 5 7.4 9 13.4 12.8 9 2-o2.2 2.5 12.2 2 15.2 Item Number o7 unit(mm) Mounting Hole Size 13.430.1 o7.2 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 2-o2.3 or 2-M2 Optical fiber connector Plug-in-type Receptacle LGC-HFC series Plug-in (DS)-type JIS C 5980 F11 type Receptacle Plug-in-type Receptacle Use these receptacles by mounting them to the sensor head of a measuring instrument, etc. They can be used for plug measurement or jack measurement by replacing the attachment. Item Number Applicable Wavelength LGC-HFCR1+R =0.85 or 1.3m LGC-HFCR2+R =1.3 or 1.55m Note Each receptacle consists of a main body, a plug attachment, and a jack attachment as a set. unit(mm) 9.5 15.2 oe14 9.5 o6 Plug attachment o6 o7 12.2 REF. Jack attachment For DS plug measurement 10 0.5 16.7 REF. 10.7 4-o2.3 Main body For DS jack measurement 9.50.1 9.50.1 Mounting Hole Size unit(mm) o7.2 4-o2.4 or 4-M2 Note 1: The main bodies or plug or jack attachments are sold individually. Note 2: Attachments for the MU plug, LGC-RH601+R (Refer to page L-69) are also available. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector SC-type Plug Pull-Out Preventive Tool/Assembly-Tool LGC-300 series SC-type Tool SC-type Plug Pull-Out Preventive Tool (SC-P type Plug Pull-Out Preventive Tool) By mounting this tool to the SC-type plug, the SC-type plug knob is covered with this tool to prevent the plug from being pulled out by mistake. Item Number Note Color : Blue (Red, yellow and green are prepared in addition to blue.) LGC-PRT301 unit(mm) 20 SCPPRT 7.4 9.4 12.8 9 3 Assembly-Tool for the SC-type and SC2-type Plugs (No. 12A Crimping Pliers) This tool is used for caulking the optical fiber cord kevler and jacket to the plug housing when assembling the SC-type and SC2 -type plugs. Item Number Note For o2mm outside diameter of optical fiber cord LGC-KP1A unit(mm) L T Jacket caulking Kevler caulking Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 70 194 Optical fiber connector SC2-type Plug LGC-300 series SC-type JIS C 5973 F04 type The SC2-type plug consists of a plug housing and ferrule. The plug housing is applicable to the simplex only, while the ferrule (Refer to page L-10) is the same as in FC-type Optical fiver connector plug or plugin type (DS) optical fiber connector plug. This plug is inserted or pulled out by using the exclusive removing tool (LGC-KP2). SC2-type Plug Housing (SC2-PH type Plug Housing) Applicable to Optical Cords having on Outside Diameter of o2 or o2.8mm (The weight reduction has been achieved by using a resin stopper.) Item Number LGC-PH373MK+R LGC-PH373MKL+R LGC-PH374MK+R LGC-PH374MKL+R Applicable Outside Diameter Note of Optical fiber cords o2mm o2.8mm For PC polishing (Boot color : Blue) For AdPC polishing (Boot color : Mauve) For PC polishing (Boot color : Blue) For AdPC polishing (Boot color : Mauve) unit(mm) 55 REF. 7.2 3.4 6 Ferrule is Excluded. Applicable to Optical Cords having on Outside Diameter of o0.9mm Item Number LGC-PH329+R LGC-PH329L+R Applicable Outside Diameter Note of Optical fiber cords o0.9mm For PC polishing (Boot color : Blue) For AdPC polishing (Boot color : Mauve) 32 REF. unit(mm) 7.2 3.4 6 Ferrule is Excluded. Applicable to Optical Cords having on Outside Diameter of o1.1mm Note of Optical fiber cords o1.1mm For AdPC polishing (Boot color : Mauve) 6 55 REF. 3.4 LGC-PH378H+R Applicable Outside Diameter 7.2 Item Number Ferrule is Excluded. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector SC2-type Plug Caulking Tool/Plug Assembly Tool LGC-300 series SC-type Tool SC2-type Plug Caulking Tool When assembling economical SC or SC2 type plugs, a Kevlar optical cable and an external shield are swaged together using this tool. The positions of the ferrule and swaging ring can be set with swaging at the same time. unit(mm) Item Number Note 58 LGC-KP370 T L 200 SC2-type Plug Assembly Tool When assembling economical SC-type plugs, a rear-assembly plug is inserted into the plug housing using this tool. unit(mm) Item Number Note LGC-KP371 23.6 55 34 100 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector SC2-type Plug Housing with Pull-Out Tool/ SC2-type Plug Removing Tool LGC-300 series SC-type Tool SC2-type Plug Housing with Pull-Out Tool This SC2-type plug housing being provided with a pull-out tool can pull out plug from SC2-type adaptor without tool. Item Number Applicable Outside Diameter of Optical fiber cords LGC-PH343+R LGC-PH343L+R o2mm Note For PC polishing (Boot color : Blue) For AdPC polishing (Boot color : Mauve) unit(mm) 6.4 12 75 REF. Ferrule is excluded. SC2-type Plug Removing Tool This tool can insert the SC2-type plug into or pull it out from the SC2-type adaptor. Item Number Note unit(mm) LGC-KP2 16 26 37 SC2PRHY HONDA 190 Operation Procedure Removing After Removal Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector SC-type Adaptor LGC-300 series SC-type JIS C 5973 F04 type Adaptor SC-type Adaptor (SC-A type Adaptor) Type of Adaptor Simplex Mounting Clamps Retaining-lock-bracket for vertical board Screw-fixing-bracket for horizontal board Housing Plastic (Color : Blue) Plastic (Color : Blue) Zinc alloys die casting Overview Retaining-lockbracket for vertical board Screw-fixing-bracket for horizontal board 2-o2.2 5.8 18 27.4 3 27.4 27.4 1.8 3 1.8 3 Retaining-lockbracket for vertical board Drawing 2 22 22 9.4 9.4 7.4 2-o2.3 7.4 18 2-o2.3 9.4 7.4 12.8 12.8 22 18 2 2 12.8 9 9 9 unit(mm) unit(mm) unit(mm) unit(mm) unit(mm) unit(mm) 180.1 Item Number 0 9.7+0.3 Mounting Hole Size 2-o2.4 or 2-M2 (for fixing with screw) 180.1 0 13.1+0.3 0 9.7 +0.3 180.1 0 13.1+0.3 2-o2.3 or 2-M2 2-o2.4 or 2-M2 (for fixing with screw) t=1.6 (Additionally t=1.0, t=1.2) t=1.6 (Additionally t=1.0, t=1.2) PhosphorBronzeAlignmentSleeve Adaptor LGC-A301 LGC-A302 LGC-A321 ZirconiaAlignmentSleeve Adaptor LGC-A303 LGC-A304 LGC-A323 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector SC-type Adaptor LGC-300 series SC-type JIS C 5973 F04 type Adaptor SC-type Adaptor (SC-A type Adaptor) Type of Adaptor Mounting Clamps Housing Simplex Retaining-lock-bracket for vertical board Plastic (Color: Blue) Overview unit(mm) 3 27.4 A 14.4 Drawing 2 12.6 9.1 7.4 12.8 9 16 unit(mm) 13.1+0.3 0 9.3+0.3 0 Mounting Hole Size A (mm) Item Number LGC-AM301 1.20.1 LGC-AM301A 1.80.1 LGC-AM303 1.20.1 LGC-AM303A Alignment- Thickness of PCB (mm) Sleeve PhosphorBronze Zirconia 1.80.1 1.0 1.6 1.0 1.6 Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector SC-type Adaptor LGC-300 series SC-type JIS C 5973 F04 type Adaptor SC-type Adaptor (SCH-2A type Adaptor/SCF-2A type Adaptor) Type of Adaptor Vertical (H type) Duplex Horizontal (F type) Duplex Mounting Clamps Retaining-lock-bracket for vertical board Retaining-lock-bracket for vertical board Housing Plastic (Color : Blue)(See Note #2) Plastic (Color : Blue)(See Note #2) Plastic (Color : Blue)(See Note #2) Screw-fixing-bracket for horizontal board Overview unit(mm) 1.8 Retaining-lock-bracket for vertical board B P 9 Type of Guide key (See Note #1) Type of Guide Key B A (Width of (Position of misinsertion misinsertion Prevention key) Prevention key) A 3.00 2.95 B 1.30 2.95 P 2.15 1.25 R 2.15 4.65 A B X unit(mm) 9.6 +0.3 +0 2-o2.4 or 2-M2 (for fixing with screw) X X X B (mm) X 0.85 1.85 X 1.85 0.85 X 1.85 1.85 0.85 0.85 X R X 2-o2.3 or 2-M2 (for fixing with screw) t=1.6 A (mm) P Type of Guide key (See Note #1) 30.70.1 t=1.6 Type of Guide Key for Connectable Vertical Duplex Plugs (See Note #3) P unit(mm) 30.70.1 +0 26.2 +0.3 2-o2.4 or 2-M2 (for fixing with screw) A 9 Type of Guide key (See Note #1) unit(mm) 180.1 +0 13.1 +0.3 Item Number 3 2-o2.3 9.4 7.4 8.5 17.9 P 7.4 25.9 34.7 12.7 A B +0 18.2 +0.3 2 30.7 12.7 9.4 A 2 - o2.3 7.4 18 Mounting Hole Size 27.4 25.9 34.7 22 9 2-o2.2 2 12.8 B Screw-fixing-bracket for horizontal board 27.4 2 Drawing unit(mm) 30.7 27.4 3 1.8 Retaining-lock-bracket for vertical board 3 unit(mm) Type of Guide Key for Connectable Horizontal Duplex Plugs (See Note #3) A B X X X X A (mm) B (mm) X 0.85 1.85 X 1.85 0.85 X 1.85 1.85 0.85 0.85 P X R X Type of Guide Key for Connectable Horizontal Duplex Plugs (See Note #3) A B X X X LGC-H2A301 [A,B,P,R] SH LGC-F2A301 [A,B,P,R] SH LGC-F2A321 [A,B,P,R] SH ZirconiaAlignmentSleeve Adaptor LGC-H2A303 [A,B,P,R] SH LGC-F2A303 [A,B,P,R] SH LGC-F2A323 [A,B,P,R] SH Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others R X X X PhosphorBronzeAlignmentSleeve Adaptor Note 1: (A,B,P and R) show the kind of guide keys, and one of these characters is inserted. Note 2: For plastic housing other than blue ones, please contact us. Note 3: X: Correspond P X X X Optical fiber connector SC-type Adaptor LGC-300 series SC-type JIS C 5973 F04 type Adaptor SC-type Adaptor (SCH-4A type Adaptor) Type of Adaptor Mounting Clamps Housing 4-Ports Retaining-lock-bracket for vertical board Plastic (Color: Blue) Overview unit(mm) 27.4 38.5 1.8 7.5 5.2 9.4 Drawing 9.43=28.2 15.4 14.8 12.8 Retaining-lock-bracket for vertical board unit(mm) Mounting Hole Size 13.1+0.3 0 38.8+0.3 0 Item Number t=1.6 (Additionally t=1.0, t=1.2) PhosphorBronzeAlignmentSleeve Adaptor LGC-H4A311 ZirconiaAlignmentSleeve Adaptor LGC-H4A313 Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector SC-type Adaptor with a Shutter LGC-300 series SC-type JIS C 5973 F04 type Adaptor with a shutter SC-type Adaptor with a Shutter (SC-A type Adaptor/SCF-2A type Adaptor/SCH-4A type Adaptor) Type of Adaptor Mounting Clamps Simplex Horizontal (F type) Duplex 4-Ports Retaining-lock-bracket for vertical board Retaining-lock-bracket for vertical board Retaining-lock-bracket for vertical board Plastic (Color: blue)(See Note #2) Plastic (Color: blue)(See Note #2) Housing Plastic (Color: blue)(See Note #2) Overview Retaining-lock-bracket for vertical board Retaining-lock-bracket for vertical board 25.9 34.7 2 12.8 30.7 12.7 2-o2.3 7.4 B 9 9 180.1 +0.3 13.1 0 Type of Guide key Item Number Type of Guide key t=1.6 (Additionally t=1.0, t=1.2) t=1.6 A (mm) B (mm) A 0.85 1.85 B 1.85 0.85 P 1.85 1.85 R 0.85 0.85 LGC-SA303 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping B X Others P 13.1 R X X X X X X LGC-SF2A303[A,B,P,R]SH Note 1: (A, B, P and R) show the kind of guide key, and one of these characters is inserted. Note 2: For other than blue plastic housing, please contact us. Note 3: X: Correspond t=1.6 (Additionally t=1.0, t=1.2) Type of Guide key for Connectable Horizontal Duplex Plugs (See Note #3) A ZirconiaAlignmentSleeve Adaptor +0.3 0 38.8+0.3 0 2-o2.4 or 2-M2 (for fixing with screw) 0 9.7 +0.3 +0.3 0 Retaining-lock-bracket for vertical board 30.70.1 0 26.2 +0.3 2-o2.4 or 2-M2 (for fixing with screw) 9.7 Mounting Hole Size 2-o2.3 A B 9.4 7.4 18 9.4 22 1.8 38.5 2 Drawing 27.4 7.5 9.43=28.2 5.2 9.4 27.4 1.8 3 1.8 3 27.4 15.4 14.8 12.8 X X LGC-SH4A313 Optical fiber connector SC-type Adaptor with a Shutter LGC-300 series SC-type JIS C 5973 F04 type Adaptor with a shutter Mounting and SC-type Adaptor with a Shutter Type of Adaptor Mounting Clamps Housing Simplex Retaining-lock-bracket for vertical board Plastic (Color: Blue) Overview 20.5 REF. unit(mm) 9.5 2-o2.3 22.5 REF. 11 5.7 REF. 18 12.8 2 Drawing The direction discernment dent of a key 3 9.4 3 REF. 18 13.1 +0.3 0 Mounting Hole Size unit(mm) 2-o2.4 or 2-M2 (for fixing with screw) 0.1 +0.3 0 9.7 1.8 27.4 Item Number t=1.6 (Additionally t=1.0, t=1.2 types) ZirconiaAlignmentSleeve Adaptor LGC-SAE300A/A303 Note: In case of using Optical Fixed Attenuators, the shutter opening side of this product guarantees only combination with SC-type Optical Fixed Attenuator of our company. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Connectors Convertor FC-type/SC-type Connectors convertor FC to SC Connector Convertor An FC adaptor and an SC-type plug are connectable to each other. Applicable Optical Fiber Mode Item Number LGC-P101/A301KC-SM+R LGC-P101/A301K-SM+R LGC-P101/A301K-GI+R Insertion Loss Single Mode 1.0dB or less Multi Mode Graded Index 0.6dB or less Ferrule Polishing Return Loss 40dB or more AdPC polishing 22dB or more PC polishing M80.75P o2.499 unit(mm) 36 REF. 2 7.4 9 o9.8 o19 2.1 9.3 SC to FC Connector Convertor An SC adaptor and an FC-type plug are connectable to each other. Applicable Optical Fiber Mode Item Number LGC-P301/A101C-SM+R LGC-P301/A101-SM+R LGC-P301/A101-GI+R Insertion Loss Single Mode 1.0dB or less Multi Mode Graded Index 0.6dB or less Ferrule Polishing Return Loss 40dB or more AdPC polishing 22dB or more PC polishing 13 9 Note: For the attenuators of connectors converter, please contact us. Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 2.4 29 M80.75P 1.8 9.4 7.4 o2.499 unit(mm) Optical fiber connector Conversion Adaptor SC-type Conversion adaptor SC-SC2 type Conversion Adaptor An SC-type plut and an SC2-type plug are connectable to each other. Type of Adaptor Mounting Clamps Housing Simplex Retaining-lock-bracket for vertical board Plastic (Color: Blue) Overview unit(mm) 27.4 9.4 7.4 3 6 1.8 22 12.8 2 9 18 Drawing 2-o2.3 Mounting Hole Size 2-o2.4 or 2-M2 (for fixing with screw) 13.1+0.3 0 180.1 unit(mm) Item Number 9.7+0.3 0 PhosphorBronzeAlignmentSleeve Adaptor LGC-AP301 ZirconiaAlignmentSleeve Adaptor LGC-AP303 Others Wire wrapping Crimping Soldering t=1.6 (Additionally t=1.0, t=1.2) IDC Press-in SMT Through hole Optical fiber connector SC2-type Adaptor LGC-300 series SC-type JIS C 5973 F04 type Adaptor The SC2-type adaptors are sorted according to the No. of cores and the materials of alignment sleeves. The vertical board retaining lock spring is attached as a mounting clamp. SC2-type 4-Ports Adaptors (SC2-4A type Adaptor) Item Number Material of Alignment Sleeve LGC-4A301 Phosphor bronze LGC-4A302 Zirconia Materials of Housing Plastic unit(mm) 24 6 28.2 6.83=20.4 6.8 15.4 15 12.8 3.9 1.8 vertical board retaining Mounting Hole Size unit(mm) +0.3 0 0 13.1+0.3 28.5 t=1.6 (Additionally t=1.0, t=1.2) SC2-type 5-Ports Adaptors (SC2-5A type Adaptor) Item Number Material of Alignment Sleeve LGC-5A301 Phosphor bronze LGC-5A302 Zirconia Materials of Housing Plastic unit(mm) 24 3.9 6 6.8 35 6.84=27.2 15.4 15 12.8 Mounting Hole Size 1.8 vertical board retaining unit(mm) +0.3 0 13.1+0.3 35.3 0 t=1.6 (Additionally t=1.0, t=1.2) Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector Simplified SC-type Optical Fiber Connector LGC-SR300 series SC-type Simplified connector Ferrule These optical connectors are constructed by simplifying the structures of SC-type and SC2-type plugs and adaptors. They are composed of a plug and a receptacle, respectively. The SC or SC2-type plug is connectable to the receptacle. A single-core or 2-ports plug is connectable to the SC-type receptacle, a 4 or 8-ports plug is connectable to the SC2-type receptacle, and a plug is connectable to the single-core and 8-ports receptacles. The ferrule is made of zirconia. Simplified SC-type Plug Simplified SC-type Simplex Receptacle Simplified SC2-type 8-ports Receptacle Specifications Items Insertion Loss Return Loss Requirements Actual Value (Average) Single Mode : 0.5dB or less 0.2dB Multi Mode Graded Index : 0.3dB or less 0.1dB Single Mode (AdPC polishing) : 40dB or more 50dB Single Mode (PC polishing) : 22dB or more 30dB Multi Mode Graded Index (PC polishing) : 22dB or more 29dB Simplified SC-type Plug Each SC-type plug is provided with a ferrule. The ferrule hole diameter ranges from o0.123mm to o0.128mm every 1m. Select these plugs according to the outside diameters of optical fiber. o0.123 LGC-RFS4 o0.124 LGC-RFS5 o0.125 LGC-RFS5.5 o0.1255 LGC-RFS6 o0.126 LGC-RFS7 o0.127 LGC-RFS8 o0.128 Mode Single mode o2.4990.0005 Multi mode Graded index Others oe5 unit(mm) 24 REF. 5.8 Wire wrapping Crimping Soldering o1.2 LGC-RFS3 Outside Diameter of the ferrule [mm] Inside Diameter of the ferrule Inside Diameter of the ferrule [mm] Outside Diameter of the ferrule Item Number IDC Press-in SMT Through hole Optical fiber connector Simplified SC-type Optical Fiber Connector LGC-SR300 series SC-type Simplified connector Receptacle Simplified SC-type Simplex Receptacle Note unit(mm) 9.4 6 5 REF. 2-o2.3 12.2 11 7.4 12.8 Attached one-zirconia-alignment-sleeve 9 LGC-SR305B 22 Attached one-phosphor-bronze-alignment-sleeve 18 Item Number LGC-SR305 3 26 unit(mm) Mounting Hole Size An External View with the Simplified SC-type Plug 0.1 18 9.7 00.3 13.1+0.3 0 2-o2.4 or 2-M2 Simplified SC-type 2-Ports Receptacle Item Number Note LGC-F2SR309 Attached two-phosphor-bronze-alignment-sleeves LGC-F2SR309B Attached two-zirconia-alignment-sleeves unit(mm) 7.8 34.7 30.7 25.5 12.7 25.5 9 2-o2.3 25.4 REF. 3 13.2 9.4 7.4 unit(mm) Mounting Hole Size 8.1+0.3 0 30.70.1 25.8+0.3 0 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 2-o2.4 or 2-M2 Optical fiber connector Simplified SC-type Optical Fiber Connector LGC-SR300 series SC-type Simplified connector Receptacle Simplified SC2-type 4-Ports Receptacle Note LGC-4SR305B Attached four-zirconia-alignment-sleeves unit(mm) 37.4 33.4 28.2 2-o2.3 SC2- HONDA Attached four-phosphor-bronze-alignment-sleeves SR JAPAN 12.4 Item Number LGC-4SR305 6 6.8 3 10.7 24.30.3 0.2 6.83=20.4 11 6 unit(mm) Mounting Hole Size 12.7 +0.3 0 33.40.1 +0.2 28.5 0 2-o2.4 or 2-M2 Simplified SC2-type 8-Ports Receptacle Note 12.4 6 6.8 2-o2.3 24.3 10.7 6.87=47.6 3 Attached eight-zirconia-alignment-sleeves 6 11 Attached eight-phosphor-bronze-alignment-sleeves LGC-8SR305B Mounting Hole Size unit(mm) 60.60.1 +0.2 55.6 0 +0.3 0 LGC-8SR305 unit(mm) 64.6 60.6 55.4 12.7 Item Number Others 2-o2.4 or 2-M2 Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Extraction Tool LGC-KPSR3 SC-type Simplified connector Tool Extraction Tool This tool is for extracting simplified SC-type plug mating with simplified receptacle. Item Number Note LGC-KPSR3 unit(mm) 30 15 7.2 5.9 5.2 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector SC-type Terminator LGC-300 series SC-type JIS C 5973 F04 type Terminator The terminator is used to prevent the reflected light from the end faces of optical connector. SC-type terminators are sorted into the SC-type and SC2-type, and the SC-type is sub-divided into the plug type and adaptor type. SC-type Terminator SC-type Plug Terminator (SC-P-TA type Terminator) Item Number LGC-PTA301SM+R Note Return loss : 40dB or more for Single Mode unit(mm) 31 REF. 9 1.8 o2.499 7.4 SC-type Adaptor Terminator (SC-A-TA type Terminator) Item Number LGC-ATA301+R Note Return loss : 40dB or more unit(mm) 9 23.7 2 12.7 12 9.3 7.4 SC2-type Adaptor Terminator (SC2-A-TA type Terminator) Item Number Note Return loss : 40dB or more unit(mm) 12 8.7 6 Others 22 9 12.7 LGC-ATA321+R Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector MU-type Optical Fiber Connector LGC-600 series MU-type JIS C 5983 F14 type MU-type Optical Fiber Connector The packaging density of this connector amounts to about 4 times as compared with the SC-type optical fiber connector. It consists of a plug (consisting of a plug housing and a o1.25mm ferrule) and an adaptor. Plug TM Adaptor TM Specifications Items Requirements Insertion Loss Return Loss Through hole SMT Press-in Actual Value (Average) : 0.5dB or less 0.2dB Multi Mode Graded Index : 0.3dB or less 0.1dB Single Mode Single Mode (AdPC polishing) : 40dB or more 50dB Single Mode (PC polishing) : 22dB or more 30dB Multi Mode Graded Index (PC polishing) : 22dB or more 29dB IDC Wire Soldering Crimping wrapping Others Optical fiber connector MU-type Plug LGC-600 series MU-type JIS C 5983 F14 type Plug MU-type Plug The MU-type plug is constructed as a push-pull lock type in the same way as in the SC-type plug, and it can easily be mounted or removed. It consists of an MU-type plug housing and a o1.25mm ferrule. High-density Plug-in-type Optical Fiber Connector Plug The MU-type plug is connected to the back board housing in the same way as in the plug-in (DS)-type plug. It can easily be removed by the high-density plug-in-type removing tool (LGC-KP601C+R) when connectors are connected closely. MU-type Optical Fiber Connector Plug This MU-type plug can be used in the same way as in the SC-type plug. It can easily to be removed by the high-density plugin-type removing tool (LGC-KP601D+R) when connectors are connected closely. MU-type Simplex Plug Housing (MU-PH type Plug Housing) This plug housing is connectable to the high-density plug-in-type back board housing, All of MU-type adaptor, Simplified Receptacle respectively. Item Number LGC-PH604+R LGC-PH604B+R Applicable Outside diameter of optical fiber cords o2mm Note For AdPC polishing (Boot color : Mauve) For PC polishing (Boot color : Blue) unit(mm) 48 REF. 23.6 5.6 6.6 4.4 Ferrule is excluded. LGC-PH603B+R o0.9mm For AdPC polishing (Boot color : Mauve) For PC polishing (Boot color : Blue) unit(mm) 42 REF. 23.6 4.4 5.6 LGC-PH603L+R Note 6.6 Item Number Applicable Outside diameter of optical fiber cords Ferrule is excluded. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector MU-type Plug LGC-600 series MU-type JIS C 5983 F14 type Plug MU-type Vertical (H type) duplex Plug Housing (MU-2PH type Plug Housing) This MU-plug is connectable to the high-density plug-in-type back board housing, MU-type vertical (H type) 2-ports and 8-ports adaptors, Simplified Receptacle 2-ports or more, respectively. Item Number Note Applicable Outside Diameter of Optical fiber cords LGC-2PH604+R For AdPC polishing (Boot color : Mauve) o2mm LGC-2PH604B+R For PC polishing (Boot color : Blue) unit(mm) Ferrule is excluded. 48 REF. 8.9 4.5 6.6 5.6 23.6 Item Number Note Applicable Outside Diameter of Optical fiber cords LGC-2PH603+R For AdPC polishing (Boot color : Mauve) o0.9mm LGC-2PH603B+R For PC polishing (Boot color : Blue) unit(mm) Ferrule is excluded. 42 REF. 8.9 4.5 6.6 5.6 23.6 MU-type Horizontal (F type) duplex Plug Housing This plug housing is connectable to the MU-type horizontal 2-ports adaptor. It is not employable as a high-density plug-in-type optical connector. Item Number Note Applicable Outside Diameter of Optical fiber cords LGC-F2PH604+R For AdPC polishing (Boot color : Mauve) o2mm LGC-F2PH604B+R For PC polishing (Boot color : Blue) unit(mm) Ferrule is excluded. 48 REF. 4.4 5.6 14.1 7.5 Item Number 23.6 Note Applicable Outside Diameter of Optical fiber cords LGC-F2PH603L+R For AdPC polishing (Boot color : Mauve) o0.9mm LGC-F2PH603B+R For PC polishing (Boot color : Blue) unit(mm) Ferrule is excluded. 42 REF. Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 23.6 5.6 14.1 7.5 4.4 Optical fiber connector Cost-effective MU-type Plug LGC-PH638H+R MU-type Cost-effective connector Plug Housing for Cost-effective MU-type Simplex Plug (MU-PHD type Plug Housing) The housing has been achieved at lower cost with the use of a stopper made of resin material. The components are designed with consideration for automatic assembly and man-hour reduction. o1.1mm Note For AdPC polishing (Boot color: Mauve) unit(mm) 5.6 LGC-PH638H+R Applicable Outside Diameter of Optical fiber cords 6.6 Item Number 4.4 23.6 54 REF. Ferrule is excluded. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Minute Diameter Ferrule LGC-600 series MU-type JIS C 5983 F14 type Minute diameter ferrule Minute Diameter Ferrule (MU-PFS type [ ] Ferrule) The inside diameter of the ferrule ranges from 0.123mm to 0.128mm every 1m. Select the ferrule according to the outside diameter of the optical fiber. This ferrule is characterized with its square flange, and it can set the eccentric direction every 90. LGC-PFS603 o0.123 LGC-PFS604 o0.124 LGC-PFS605 o0.125 LGC-PFS6055 o0.1255 LGC-PFS606 o0.126 LGC-PFS607 o0.127 LGC-PFS608 o0.128 Outside Diameter of the Ferrule [mm] unit(mm) Mode Single Mode o1.2490.0005 Multi Mode Graded Index oe2.6 12 4.95 1.5 o1 o1.8 Inside Diameter of the Ferrule [mm] Outside Diameter of the Ferrule Inside Diameter of the Ferrule Item Number Minute Diameter Ferrule for o1.1mm Optical Fiber Cord (MU-PFSD type [ ] Ferrule) The inside diameter of the ferrule ranges from 0.123mm to 0.128mm every 1m. Select the ferrule according to the outside diameter of the optical fiber. This ferrule is characterized with its square flange, and it can set the eccentric direction every 90. o0.123 LGC-PFSD604 o0.124 LGC-PFSD605 o0.125 LGC-PFSD6055 o0.1255 LGC-PFSD606 o0.126 LGC-PFSD607 o0.127 LGC-PFSD608 o0.128 Through hole SMT Press-in IDC unit(mm) Mode Single Mode o1.2490.0005 Wire Soldering Crimping wrapping Others Multi Mode Graded Index oe2.6 12 4.95 1.5 o0.6 o1.5 LGC-PFSD603 Outside Diameter of the Ferrule [mm] Outside Diameter of the Ferrule Inside Diameter of the Ferrule Item Number Inside Diameter of the Ferrule [mm] Optical fiber connector MU-type Plug Caulking Tool LGC-600 series MU-type Tool Caulking Tool When assembling MU-type plugs, a Kevlar optical cable and a plug housing are swaged together using this tool. An attachment is provided, which sets the plug housing and positioning boss in the proper direction. Item Number Note LGC-KP604A unit(mm) L 200 T 58 When assembling cost-effective MU-type plug components, a Kevlar optical cable and a plug housing are swaged together by using this tool, at the specified distance between the flange and swaging ring. Item Number for LGC-PH638H+R unit(mm) L T 200 LGC-KP630 Note 58 Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Cost-effective MU-type Plug assembly tool/ Tool for inserting plug swaging seats LGC-600 series MU-type Tool When assembling economical MU-type plugs, a rear-assembly is inserted into a front-pre-assembly using this tool. Item Number Note LGC-KP631 unit(mm) 23.6 55 34 100 When assembling economical MU-type plugs, an optical cable is inserted into the hole of a plug swaging seat using this tool. This tool is also used when assembling economical SC or SC type plugs. Item Number Note LGC-KP632 unit(mm) 45 38 48.5 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 19.3 Optical fiber connector MU-type Adaptor LGC-600 series MU-type JIS C 5983 F14 type Adaptor MU-type Adaptor Mouting Bracket type (The following overview drawings and mounting views show single port type adaptors.) Mounting Bracket Type Free Insertion-Bracket Retaining-Lock-Bracket for Vertical Board for Horizontal Board Screw-Fixing-Bracket for Horizontal Board Screw-Fixing-Bracket for Vertical Board Overview A unit(mm) unit(mm) unit(mm) unit(mm) C C 2-o2.4 or 2-M2 D D B Mounting Hole Size 4-o2.4 F t=1.6 t=1.6 Alignment sleeve material designator [none]: Zirconia [P]: Phosphor bronze - Item Number LGC-2A640[ ] Size - Item Number 8-ports Size Vertical 2-ports (H-type) LGC-A640[ ] Horizontal 2-ports (F-type) Single Port Item Number of MU-type Adaptor Item Number Size Item Number LGC-8A640[ ] Size LGC-A641[ ] A B - 9.50.1 12.70.1 LGC-A642[ ] A B 12.70.1 12.70.1 16.50.1 12.70.1 40.60.1 12.70.1 0 0.3 0 E LGC-2A643[ ] 0 0.3 0 LGC-A644[ ] E 0 12.50.1 F G 14.00.1 +0.3 14.3 + 10.1 C D LGC-2A644[ ] 5.00.1 15.00.1 F G 17.80.1 LGC-F2A602+R - - +0.3 17.8 + 7.6 C D LGC-8A641[ ] A B 10.7 + 7.6 LGC-2A642[ ] LGC-F2A601+R A B LGC-A643[ ] +0.3 C D LGC-2A641[ ] LGC-F2A600+R - 2-o2.4 or 2-M2 G E 0 0.3 0 LGC-8A642[ ] LGC-8A643[ ] +0.3 42.3 + 10.1 C D 0 0.3 0 E LGC-8A644[ ] F G 45.70.1 25.00.1 15.00.1 Note 1: The horizontal (F type) 2-port adapter uses a metal holder. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector MU-type Adaptor with a Shutter LGC-600 series MU-type JIS C 5983 F14 type Adaptor with a shutter MU-type Adaptor with Shutter This connector is a MU-type adaptor built in light shielding shutters. Mouting Bracket type (The following overview drawings and mounting views show single port type adaptors.) Mounting Bracket Type Retaining-Lock-Bracket Screw-Fixing-Bracket Insertion-Bracket for Vertical Board for Horizontal Board for Horizontal Board (Board thickness: 1.6mm) (Board thickness: 1.6mm) Free Screw-Fixing-Bracket for Vertical Board Overview A unit(mm) unit(mm) unit(mm) unit(mm) C C D D B Mounting Hole Size 2-o2.4 or 2-M2 G E 2-o2.4 or 2-M2 4-o2.4 F t=1.6 t=1.6 Alignment sleeve material designator [none]: Zirconia [P]: Phosphor bronze Vertical 2-ports (H-type) Single Port Item Number of MU-type Adaptor Through hole Item Number LGC-SA640[ ] Item Number LGC-2SA640[ ] Size SMT A B - Size - Press-in IDC LGC-SA641[ ] 9.50.1 12.70.1 LGC-SA642[ ] C D LGC-2SA641[ ] A B 12.70.1 12.70.1 Wire Soldering Crimping wrapping +0.3 0 +0.3 0 E LGC-2SA642[ ] C D Others 10.7 7.6 LGC-SA643[ ] 14.3 10.1 F G LGC-2SA643[ ] +0.3 0 +0.3 0 14.00.1 LGC-SA644[ ] E 17.80.1 0 12.50.1 LGC-2SA644[ ] F G 5.00.1 15.00.1 Optical fiber connector MU-type Adaptor LGC-A622[ ] LGC-2A622[ ] MU-type JIS C 5983 F14 type Adaptor Screw-Fixing-Bracket for Vertical Board type Item Number Material of Alignment Sleeve LGC-A622P Phosphor bronze LGC-A622 Zirconia Housing Material Plastic unit(mm) 6.6 2.5 1.8 9.8 14.5 2-o2.3 19 1.1 REF. 26 +0.2 9.9 0 14.50.1 REF. 0 6.9+0.2 +0.2 (2-o2.3 0 or 2-M2) (for fixing with screw) Mounting Hole Size t= 1.6 Material of Alignment Sleeve Plastic unit(mm) 26 2-o2.3 1 1.1 REF. 1 1.8 12 18 4.5 9.8 2.5 +0.2 10.1 0 +0.2 Zirconia 12.1 0 Phosphor bronze LGC-2A622 22 LGC-2A622P Housing Material 180.1 REF. Item Number +0.2 (2-o2.3 0 or 2-M2) (for fixing with screw) Mounting Hole Size t= 1.6 Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector MU-type Adaptor LGC-4A622[ ] LGC-8A622[ ] MU-type JIS C 5983 F14 type Adaptor Screw-Fixing-Bracket for Vertical Board type Item Number Material of Alignment Sleeve LGC-4A622P Phosphor bronze LGC-4A622 Zirconia Housing Material Plastic 26 1.1 REF. 9.8 3 3 1 1 unit(mm) 2.5 1.8 21.5 27.5 4.5 5 4.5 31.5 2-o2.3 +0.2 +0.2 21.6 0 27.50.1 REF. 10.1 0 Mounting Hole Size t=1.6 +0.2 0 (2-o2.3 or 2-M2) (for fixing with screw) Item Number Material of Alignment Sleeve LGC-8A622P Phosphor bronze LGC-8A622 Zirconia Housing Material Plastic unit(mm) 26 5 3 3 1 1 +0.2 10.1 0 +0.2 5 1.8 40.6 0 7 2.5 46.50.1 REF. 7 40.5 4.5 5 4.5 5 4.5 5 4.5 50.5 46.5 1.1 REF. 9.8 2-o2.3 +0.2 (2-o2.3 0 or 2-M2) (for fixing with screw) Mounting Hole Size t=1.6 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector MU-type Adaptor LGC-16A622[ ] MU-type JIS C 5983 F14 type Adaptor Screw-Fixing-Bracket for Vertical Board type Housing Material Plastic unit(mm) F D D B B 9 9 7 7 5 5 3 3 1 1 8.6 Others 0 -0.1 0 (2-o2.30.2 or 2-M2) (for fixing with screw) Wire wrapping Crimping Soldering 0 6.7+0.2 0 1.6 -0.3 F 0 10.1+0.3 0 1.2-0.3 0 1.2 0.1 0 9.80.2 0 6.6-0.2 860.1 REF. 0 80.1+0.2 0 1.60.1 2-o2.3 4.5 5 4.5 5 4.5 5 4.5 6 .5 4.5 5 4.5 5 4.5 5 4.5 860.1 900.2 260.3 2.50.3 +0.2 1.8-0.1 80-0.2 Material of Alignment Sleeve Phosphor bronze Zirconia 1.1 REF. Item Number LGC-16A622P LGC-16A622 IDC 0 8.7+0.2 11 Mounting Hole Size t= 1.6 Press-in SMT Through hole Optical fiber connector MU-type Adaptor (6.25mm pitch between terminals) LGC-2A632[ ] LGC-8A632[ ] MU-type JIS C 5983 F14 type Adaptor Screw-Fixing-Bracket for Vertical Board type Item Number LGC-2A632P LGC-2A632 Material of Alignment Sleeve Phosphor bronze Zirconia Housing Material Plastic 1.1 REF. 2.5 1.8 15.5 25.5 21.5 6.25 2-o2.3 1 unit(mm) 26 9.8 1 15.6+0.2 0 21.50.1 0 10.1+0.2 0 Mounting Hole Size t= 1.6 2-o2.4 or 2-M2 Housing Material Plastic 2-o2.3 260.3 2.50.3 -0.1 1.80.2 Press-in IDC Wire Soldering Crimping wrapping Others 7 6 6 5 5 4 4 3 3 2 2 1 1 0 8.6-0.1 0 1.6-0.3 7 0 1.2-0.3 8 59.50.1 REF. 0 53.6+0.2 6.25 6.25 6.25 SMT 8 8.5 0 1.2+0.1 6.25 6.25 6.25 59.50.1 63.50.2 0 53.5-0.2 Through hole unit(mm) 0 10.1+0.3 0 6.7+0.2 9.80.2 0 6.6-0.1 0 1.6+0.1 Material of Alignment Sleeve Phosphor bronze Zirconia 1.1 REF. Item Number LGC-8A632P LGC-8A632 0 or 2-M2) (2-o2.3+0.2 0 8.7+0.2 (for fixing with screw) Mounting Hole Size t= 1.6 Optical fiber connector MU-type Adaptor with a Shutter (6.25mm pitch between terminals) LGC-600 series JIS C 5983 F14 type Adaptor with a shutter Housing Material Plastic unit(mm) 26 1.1 REF. 9.8 2-o2.3 1 1 2.5 1.8 15.5 Material of Alignment Sleeve Phosphor bronze Zirconia 25.5 21.5 6.25 Item Number LGC-2SA632P LGC-2SA632 MU-type 1 1 The mounting hole size is equal to that of LGC-2A632. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector MU-type/High-density Plug-in-type Optical Fiber Connector LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type High-density Plug-in-type Optical Fiber Connector This connector has been developed for high-density mounting the plug-in-type (DS) optical connector. Its packaging density amounts to about 4 times as compared with the plug-in-type (DS) connector. It consists of a plug (consisting of a plug housing and a o1.25mm ferrule), a back board housing, a package housing, a sleeve holder include alignment sleeve, and a jack (consisting of a jack housing and a o1.25mm ferrule). Plug Back Board Housing Package Housing Sleeve Holder Jack Specifications Items Requirements Insertion Loss Return Loss Through hole SMT Press-in Actual Value (Average) : 0.5dB or less 0.2dB Multi Mode Graded Index : 0.3dB or less 0.1dB Single Mode Single Mode (AdPC polishing) : 40dB or more 50dB Single Mode (PC polishing) : 22dB or more 30dB Multi Mode Graded Index (PC polishing) : 22dB or more 29dB IDC Wire Soldering Crimping wrapping Others Optical fiber connector High-density Plug-in-type Back Board Housing/ Package Housing LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type Back board/Package housing High-density Plug-in-type Back Board Housing (HA, B Housing) These housings are sorted into those for 2-ports type, 4-ports type, and 8-ports type. Each housing is mounted by inserting it to the back board and then, fixing it with screws. 2-ports High-density Plug-in-type Back Board Housing (C-L2HA, B Housing) This housing is connected to the 2-ports high-density plug-in-type package housing (LGC-L2PA+R). 18.9 4.5 Back Board Thickness 0 0.1 0.1 (4-R1-Recess) 6.2 7.71 11.89 3.2mm +0.2 LGC-L2HB+R unit(mm) 8.39 2.4mm Mounting Hole Size 12.3 LGC-L2HA+R unit(mm) 13.2 Item Number 17.8 15.24 4-R0.8 0.1 1 2 9.8 12.2 0.1 18.59 4-ports High-density Plug-in-type Back Board Housing (C-L4HA, B Housing) This housing is connected to the 4-ports high-density plug-in-type package housing (LGC-L4PA+R). 23.6 4.53=13.5 Back Board Thickness 2.4mm LGC-L4HB+R 3.2mm Mounting Hole Size unit(mm) 19.6+0.2 0 13.510.1 6.2 11.890.1 8.39+0.2 0 12.3 LGC-L4HA+R unit(mm) 13.2 Item Number 19.3 10.16 4-3.35+0.2 0 9.8 8-R0.8 Ref. (4-R1-Recess) 8-ports High-density Plug-in-type Back Board Housing (C-L8HA, B Housing) This housing is connected to the 8-ports high-density plug-in-type package housing (LGC-L8PA+R). Back Board Thickness +0.2 0 0.1 0.1 11.89 + 8.39 0.2 0 31.29 37.3 27.94 8-R0.8 (4-R1-Recess) 4-3.35+0.2 0 1 2 3 4 5 6 7 3.2mm unit(mm) 37.6 8 LGC-L8HB+R Mounting Hole Size 13.2 2.4mm 6.2 12.3 LGC-L8HA+R unit(mm) 41.6 4.57=31.5 9.8 Item Number Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector High-density Plug-in-type Package Housing LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type Package housing High-density Plug-in-type Package Housing (PA Housing) These housings are sorted into those for 2-ports type, 4-ports type, and 8-ports type. This housing is mounted to the package board surface with screws. 2-ports High-density Plug-in-type Package Housing (C-L2PA Housing) This housing is connected to the 2-ports high-density plug-in-type back board housing (LGC-L2HA+R or LGC-L2HB+R). unit(mm) Package Board Thickness Item Number 1.6~2.0mm 10.5 9 20.9 5.08 20.32 (Mounting Pitch) 2-o2.1 2-o3.2 0.1 2 8.61 0.1 5.08 12.7 18.7 4.5 LGC-L2PA+R unit(mm) Mounting Hole Size 1 0.1 12.7 4-ports High-density Plug-in-type Package Housing (C-L4PA Housing) This housing is connected to the 4-ports high-density plug-in-type back board housing (LGC-L4HA+R or LGC-L4HB+R). Package Board Thickness unit(mm) 1.6~2.0mm 10.5 9 20.9 5.08 26.2 (Mounting Pitch) 2-o2.1 3 2 21.59 25.1 4 4.53=13.5 LGC-L4PA+R unit(mm) Mounting Hole Size 1 8.610.1 5.080.1 Item Number 2-o3.2 21.590.1 8-ports High-density Plug-in-type Package Housing (C-L8PA, B Housing) This housing is connected to the 8-ports high-density plug-in-type back board housing (LGC-L8HA+r or LGC-L8HB+R). unit(mm) 10.5 20.9 5.08 1.6~2.0mm 9 8 4.57=31.5 SMT Press-in IDC Wire Soldering Crimping wrapping 43.18 (Mounting Pitch) 7 2-o2.1 2-o3.2 39.37 43 6 5 4 3 2 1 Through hole unit(mm) Mounting Hole Size Others 0.1 LGC-L8PA+R Package Board Thickness 8.61 0.1 5.08 Item Number 0.1 39.37 Optical fiber connector High-density Plug-in-type Package Housing LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type Package housing High-density Plug-in-type Package Housing Cap (PA Housing Cap) These are caps for High-density Plug-in-type Package Housing Item Number LGC-CL2PB No. of contacts 2-ports 17.8 4.5 12.8 11 Item Number LGC-CL4PB No. of contacts 4-ports 22.4 4.53=13.5 12.8 11 No. of contacts 8-ports 40.4 4.57=31.5 11 12.8 Item Number LGC-CL8PB Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Housing for Back Board for Hard Metric LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type Back board housing Housing for Back Board for Hard Metric (HA Housing) It connects it with housing for package for hard metric LGC-LZ8PA+R Item Number Back Board Thickness (L) Back Housing Color LGC-LZ8HA+R 3.7mm Beige LGC-LZ8HB+R 3.1mm Black 48.6 11.6 4.53=13.5 12.4 4.2 L 17.2 4.53=13.5 46 13.8 35 27 unit(mm) 270.05 0.05 5.20.05 6 REF. 8.50.05 350.05 24.60.05 10 REF. 1.45 8.950.05 0.50.05 Mounting Hole Size 1.450.05 3.05 REF. 18.20.05 19.8 REF. 44.4 REF. R are all R0.8 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector Housing for Package for Hard Metric LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type Package housing Housing for Package for Hard Metric (PA Housing) It connects it with housing for backboard for hard metric LGC-LZ8HA or LGC-LZ8HB+R Item Number LGC-LZ8PA+R 4.53=13.5 20.9 4.53=13.5 49.5 9 45.6 11.6 4 unit(mm) 8.50.1 4.5 REF. Mounting Hole Size .1 40.1 o2 2- .2 o3 2- 45.60.1 Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Package Housing Cap for Hard Metric Housing Misinsertion Prevention Key for Hard Metric LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type Package housing Package Housing Cap for Hard Metric (PA Housing Cap) There are caps for Package Housing for Hard Metric LGC-LZ8PA+R. Item Number unit(mm) LGC-CLZ8PB 47.6 11.6 11.6 4.53=13.5 15.9 4.53=13.5 Housing Misinsertion Prevention Key for Hard Metric This is a housing misinsertion prevention key for hard metric. A set is composed of two keys for the backboard and two keys for the package. Item Number unit(mm) LGC-LZ8KY B 10 REF. P H LGC-LZ8KY 32.7 REF. P HONDA JAPAN H A SMT Press-in IDC Wire Soldering Crimping wrapping Others P 9.5 10.2 for Back Board Through hole 5.5 4 REF. 6.4 H 2.5 REF. 2.1 2.1 0.38 REF. 2.1 3.9 3.8 3.9 0.7 REF. A: for Back Board B: for Package for Package Optical fiber connector High-density Plug-in-type Jack LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type Jack High-density Plug-in-type Jack This high-density plug-in-type jack is connected to the high-density plug-in-type package housing. It consists of a high-density plug-in-type jack housing and a o1.25mm ferrule. Inserted ferrule, o1.25mm Ferrule, is the same as in the MU-type plug. (LGC-PFS60[ ]) For removing it, use its exclusive removing tool. (LGC-KP602C) High-density Plug-in-type Jack Housing (MUJ-PH type plug housing) This jack housing is connected to the high-density plug-in-type package housing. Item Number LGC-PH624+R LGC-PH624B+R Applicable Outside diameter of optical fiber cords o2mm Note For AdPC polishing (Boot color : Mauve) For PC polishing (Boot color : Blue) unit(mm) 4.4 4.75 3.75 41 REF. 15 Ferrule is excluded. LGC-PH623B+R o0.9mm Note For AdPC polishing (Boot color : Mauve) For PC polishing (Boot color : Blue) unit(mm) 32.3 REF. 3.75 15 4.4 LGC-PH623L+R Applicable Outside diameter of optical fiber cords 4.75 Item Number Ferrule is excluded. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector High-density Plug-in-type MU-type Sleeve Holder/Dummy plug/Dummy Jack LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type Sleeve Holder/Dummy plug/Dummy Jack MU-type Sleeve Holder (MU-SH type Sleeve Holder) This sleeve holder contains a zirconia alignment sleeve. Use the MU-type Sleeve Holder Mountig / Removing Tool (LGCKP603C) when mounting or removing this sleeve holder. Item Number Note unit(mm) LGC-AL8PA+R o2.56 o3.2 8.15 High-density Plug-in-Type Jack Side (Gold Plated Side) MU-Type Plug Side Dummy plug (MU-DP type Dummy Plug) Item Number Note unit(mm) LGC-DP601-1 23.6 5.6 6.6 4.4 Dummy Jack Item Number Note unit(mm) LGC-DJ601-1 21.2 o6 4 REF. Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector Simplified MU-type Optical Fiber Connector LGC-SR600 series MU-type Simplified connector Ferrule These optical connectors are constructed by simplifying the structures of MU-type plugs and adaptors. MU-type or Simplified MU-type plug is connectable to the receptacle. When pulling out simplified MU-type plugs from simplified receptacles, the extracting tool LGC-KPSR6 (Refer to the page L-67) is required. Simplified MU-type Plug Simplified MU-type Simplex Receptacle Simplified MU-type 8-ports Receptacle Alignment Sleeve Specifications Item Actual Value (Average) Requirements Single Mode Insertion Loss : 0.5dB or less 0.2dB Multi Mode Graded Index : 0.3dB or less Return Loss 0.1dB Single Mode (AdPC polishing) : 40dB or more 50dB Single Mode (PC polishing) : 22dB or more 30dB Multi Mode Graded Index (PC polishing) : 22dB or more 29dB Simplified MU-type Plug Each simplified MU-type plug is provided with a ferrule of zirconia. The inside diameter of the ferrule can be selected to align with the outside diameter of an optical fiber as follows. LGC-PFS634 o0.124 LGC-PFS635 o0.125 LGC-PFS6355 o0.1255 LGC-PFS636 o0.126 LGC-PFS637 o0.127 LGC-PFS638 o0.128 o1.2490.0005 Single mode 3 unit(mm) 17.8 REF. 3.75 REF. o1.2 o0.123 Inside diameter of ferrule LGC-PFS633 Mode Outside diameter of ferrule Inside diameter Outside diameter of ferrule of ferrule [mm] [mm] 3 Item Number Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Simplified MU-type Receptacle LGC-SR631[ ] MU-type Simplified connector Receptacle Screw-Fixing-Bracket for Vertical Board type Item Number Material of Alignment Sleeve Phosphor bronze LGC-SR631B Zirconia LGC-SR631 Housing Material Plastic unit(mm) 6.6 9.9 19 14.5 1.1 REF. 2-o2.3 10 +0.2 0 14.5 0.1 REF. 6.7 +0.2 0 +0.2 (2-o2.3 0 or 2-M2) (for fixing with screw) Mounting Hole Size t=1.6 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 2.5 1.8 8.2 20.5 11.75 Optical fiber connector Simplified MU-type Receptacle LGC-2SR631[ ] LGC-4SR631[ ] LGC-8SR631[ ] MU-type Simplified connector Receptacle Screw-Fixing-Bracket for Vertical Board type Item Number LGC-2SR631B LGC-2SR631 Material of Alignment Sleeve Phosphor bronze Zirconia Housing Material Plastic unit(mm) unit(mm) LGC-2SR631[ ] LGC-4SR631[ ] 22 18 12 4.5 31.5 27.5 21.5 14 REF. 4.5 5 4.5 Note: Dimensions in axial direction are same as the dimensions of LGC-8SR631 [ ], as shown below. 180.1 REF. +0.2 (2-o2.3 0 or 2-M2) (for fixing with screw) +0.2 12.1 0 27.50.1 REF. +0.2 21.6 0 +0.2 Zirconia +0.2 (2-o2.3 0 or 2-M2) (for fixing with screw) 10.1 0 LGC-4SR631 Phosphor bronze 10.1 0 LGC-4SR631B Note: Dimensions in axial direction are same as the dimensions of LGC-8SR631 [ ], as shown below. Material of Alignment Sleeve +0.2 Item Number 2-o2.3 9.8 9.8 2-o2.3 Mounting Hole Size t=1.6 Mounting Hole Size t=1.6 unit(mm) LGC-8SR631[ ] 33 REF. 4.5 5 4.5 5 4.5 5 4.5 3 5 7 1 3 5 7 1.1 REF. 50.5 46.5 40.5 20.5 1.8 Zirconia 2.5 Phosphor bronze 2-o2.3 46.50.1 REF. 0 40.6+0.2 0 or 2-M2) (2-o2.3+0.2 (for fixing with screw) +0.2 LGC-8SR631 10.1 0 LGC-8SR631B Material of Alignment Sleeve 11.75 9.8 1 Item Number Mounting Hole Size t=1.6 Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Simplified MU-type Receptacle LGC-16SR631[ ] MU-type Simplified connector Receptacle Screw-Fixing-Bracket for Vertical Board type Item Number Material of Alignment Sleeve Phosphor bronze LGC-16SR631B Zirconia LGC-16SR631 Housing Material Plastic unit(mm) 72.5 REF. 4.5 5 4.5 5 4.5 5 4.5 6.5 4.5 5 4.5 5 4.5 5 4.5 3 5 7 9 B D F 1 3 5 7 9 B D F 2.5 90 86 80 860.1 REF. 80.1+0.2 0 +0.2 0 0 10.1+0.2 (2-o2.3 or 2-M2) (for fixing with screw) Mounting Hole Size t=1.6 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 20.5 1.1 REF. 1.8 11.75 9.8 1 2-o2.3 Optical fiber connector Simplified MU-type Receptacle LGC-2SR611[ ] LGC-4SR611[ ] LGC-8SR611[ ] MU-type Simplified connector Receptacle Spring-Lock type Item Number LGC-2SR611B LGC-2SR611 Material of Alignment Sleeve Phosphor bronze Zirconia Housing Material Plastic unit(mm) LGC-2SR611[ ] 23.3 22 19.9 14 REF. 4.5 5 4.5 1.6 REF. 1.6 REF. 13.8 12.5 10.4 4.5 9.8 2.5 3 9.8 2.5 3 LGC-4SR611 1 1 Item Number LGC-4SR611B 1 1 Note: Dimensions in axial direction are same as the dimensions of LGC-8SR611 [ ], as shown below. unit(mm) LGC-4SR611[ ] Note: Dimensions in axial direction are same as the dimensions of LGC-8SR611 [ ], as shown below. Material of Alignment Sleeve unit(mm) Phosphor bronze Zirconia 1.6 REF. LGC-8SR611[ ] 4.5 5 7 5 7 9.8 2.5 4.5 3 1 2.2 Phosphor bronze 9 20.5 Zirconia 7 Material of Alignment Sleeve 8.2 LGC-8SR611 5 3 1 Item Number LGC-8SR611B 5 42.3 41 38.9 33 REF. 4.5 5 4.5 Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Simplified MU-type Receptacle LGC-16SR611[ ] MU-type Simplified connector Receptacle Spring-Lock type Item Number Material of Alignment Sleeve Housing Material Phosphor bronze LGC-16SR611B Plastic Zirconia LGC-16SR611 1.6 REF. unit(mm) 5 4.5 5 4.5 5 4.5 5 4.5 5 4.5 B D F 9 B D F 5 9 5 3 7 3 1 8.2 9 20.5 2.2 7 5 7 1 9.8 2.5 4.5 81.8 80.5 78.4 72.5 REF. 4.5 6.5 4.5 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector Removing Tool LGC-KPSR6 MU-type Tool Removing Tool This tool is for extracting simplified MU-type plug mating with simplified receptacle. Item Number Note LGC-KPSR6 unit(mm) 15 5 3.1 3.3 Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector MU-type Terminator MU-type/High-density Plug-in-type Terminator MU-type Terminator Terminators are used for preventing the reflected light at the end faces of optical connectors. They are sorted into the plug type, jack type, and adaptor type. MU Plug type Terminator (MU-P-TA type Terminator) Item Number Note Return loss : 40dB or more for Single Mode LGC-PTA601+R unit(mm) 27 REF. 23.6 5.6 6.6 o1.249 4.4 MU Jack type Terminator (MU-J-TA type Terminator) Item Number Note Return loss : 40dB or more for Single Mode LGC-PTA621+R unit(mm) o1.249 20.5 REF. 15 4.4 4.75 3.75 MU Adaptor type Terminator Item Number Note Return loss : 40dB or more LGC-ATA601+R unit(mm) 7.5 9.3 20 22.5 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector MU-type Receptacle/MU-RA Receptacle Attachments LGC-600 series MU-type/High-density Plug-in-type JIS C 5983 F14 type Receptacle MU-type Receptacle/MU-RA Receptacle Attachments MU-type Receptacle Item Number Note o20 unit(mm) 15 7.5 13.43 LGC-R605 14.5 2-o2.3 0.5 o3.8 Mounting Hole Size 13.430.1 2-o2.3 or 2-M2 o4 MU-RA Receptacle Attachments Use these receptacles by mounting them to measuring instruments, etc. The main body is the same as in the receptacle of plug-in-type optical connector (LGC-HFCR1+R or LGC-HFCR2+R: Refer to page L-19) and it is applicable by replacing the attachment. unit(mm) oe14 9.5 14.1 Attachment only o6 4-o2.3 Plug Attachment o1.252 10 15.6 REF. LGC-RH601+R Note 0.5 Item Number o7 Main body The mounting hole size is equal to that of LGC-HFCR[ ]+R. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector MU-type Tool LGC-600 series MU-type Tool MU-type Plug Mounting/Removing Tool (C-LMU type [ ] Plug Mounting/Removing Tool) Plug removing tools, jack removing tool, cleaning tool, are available. MU-type Plug Mounting/Removing Tool (C-LMU type [ ] Plug Mounting/Removing Tool) This tool is used for mounting the MU-type plug to or removing it from the back board housing. Item Number Size A 12.1mm LGC-KP601D+R 9.1mm Note C-LMU type B plug mounting/removing tool For MU-type adaptor plug C-LMU type A plug mounting/removing tool o21 REF. 13.2 A LGC-KP601C+R Name For high-density plug-in-type back board housing 300 REF. Mounting Removing MU-type Plug Mounting/Removing Tool This tool is a smaller-sized and light-weight MU-type plug mounting/removing tool. Two kinds of tools are provided, one is a tool that integrates mounting and removing tools; the other is a tool that separates the mounting and removing tools and puts them in chains. Another tool is also provided, from which guide hardware is removed from the mounting side of the tool, so that the mounting/removing tool can be used for housing for the backboard. Item Number LGC-KP605B 4.8 4.8 LGC-KP605A D ISC ON N EC T C ON N EC T DIS CONNE CT 150 65 65 5.5 REF. 5 7 7 5 5.5 REF. Removing side Mounting side Removing side Item Number Name Note LGC-KP605A Type A LGC-KP605B Type B LGC-KP605C Type C LGC-KP605D Type D Integrated type, for MU type adaptor Separated type, for MU type adaptor Integrated type, for MU type adaptor and backboard housing Separated type, for MU type adaptor and backboard housing Through hole CONNE CT 150 SMT Press-in IDC Wire Soldering Crimping wrapping Others Mounting side Form of tool mounting side ends of LGC-KP605C and LGC-KP605D Optical fiber connector MU-type Tool LGC-600 series MU-type Tool MU-type Sleeve Holder Mounting/Removing Tool (MU-SH type Sleeve Holder Mounting/Removing Tool) This tool is used for mounting the MU-type sleeve holder to or removing the sleeve holder from the package housing. Item Number Removing After Removal LGC-KP603C High-density Plug-in-type Jack Removing Tool (MUJ-PH type Plug Removing Tool) This tool is used for removing the High-density Plug-in-type Jack from the package housing. Note Item Number LGC-KP602C o10 REF. unit(mm) 100 REF. Removing After Removal High-density Plug-in-type Jack Mounting/Removing Pad The high-density plug-in-type jack can be freely removed from the back board housing and adaptor by mounting this pad to the jack. Item Number Mounted Condition unit(mm) LGC-Z43 23.6 5.6 4.4 Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Plug-in (DS)-type Optical Connector LGC-HFC series Plug-in (DS)-type JIS C 5980 F11 type The plug-in (DS)-type optical connector is applicable to the exchange and transmission systems. It is mountable together with a coaxial connector. It is composed of a plug (consisting of a plug housing and a o2.5mm ferrule), a back board housing, a package housing, and a jack (consisting of a jack housing and a o2.5mm ferrule). Plug Back Board Housing Package Housing Jack Specifications Items Requirements Insertion Loss Return Loss : 0.5dB or less 0.2dB Multi Mode Graded Index : 0.3dB or less 0.1dB Single Mode Single Mode (AdPC polishing) : 40dB or more 50dB Single Mode (PC polishing) : 22dB or more 30dB Multi Mode Graded Index (PC polishing) : 22dB or more 29dB Note 1: Please contact us for details about this series. Through hole SMT Press-in Actual Value (Average) IDC Wire Soldering Crimping wrapping Others Optical fiber connector Optical Fiber Cord with Connectors (Patch Cord) Optical fiber cord with connectors An optical fiber cord with connectors is produced by harnessing various optical connectors in this catalog. Cord type (Stamp item number and "HONDA") Cord length [m] A side B side Note: The cord length shows the length from the rear end of one connector to the rear end of the other connector excluding the boots. Item Number Configuration In case of those other than plug-in Optical fiber connector (In case of the example shown in the above figure) L G C - PA 102 PA 3 5 3 -- A Side Connector Name B Side Connector Name Set the connector having a lower number in the table to the A side. Deleted in case of a cord with a connector at one end only. A Side Polishing Shape SM B Side Polishing Shape 2 +R Cord Length (Unit: m) RoHS Mode Entry characters Polishing shape Entry characters Polishing shape Entry characters Type P PC P PC SM 10/125SM (=1.31m) PA AdPC PA AdPC 15SM PN Angled FLAT PN Angled FLAT GI 8/125SM (=1.55m) 50/125GI (=1.31m) Deleted in case of a cord with a connector at one end only. Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole Optical fiber connector Optical Fiber Cord with Connectors (Patch Cord) Optical fiber cord with connectors Types of A or B side connector name Be careful since the part numbers of the connectors to be harnessed are different from entry characters. No. Entry Characters Part No. of Connector Housing (See Note #1) Connector Type Outside Diameter of Optical Fiber Cord 1 102 FC-type plug LGC-PH2+R o2 2 103 FC-type plug LGC-PH3 [ ]+R o0.9 (Buffered fiber) 3 105 FC-type plug (Crimp Assembly type) LGC-PH5 [ ]+R o2 4 353 SC-type plug LGC-PH353M [ ]+R o2 5 305 SC-type plug LGC-PH305M [ ] o0.9 (Buffered fiber) 6 373 SC2-type plug LGC-PH373M [ ]+R o2 7 329 SC2-type plug LGC-PH329 [ ]+R o0.9 (Buffered fiber) 8 604 MU-type plug LGC-PH604 [ ]+R o2 9 603 MU-type plug LGC-PH603 [ ]+R o0.9 (Buffered fiber) 10 624 High-density plug-in-type jack LGC-PH624 [ ]+R o2 11 623 High-density plug-in-type jack LGC-PH623 [ ]+R o0.9 (Buffered fiber) Note 1: The character to be inserted in [ ] depend on the boot colors. Note 2: For the various master cords, please contact us. Note 3: For the cord of SC and MU-type Vertical and Horizontal 2-ports plug, please contact us. Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others Optical fiber connector Connector Convertor SC-type/MU-type Connector convertor SC to MU Connector Convertor An SC adaptor and an MU-type plug are connectable to each other. Item Number Applicable Optical Fiber Mode Insertion Loss Ferrule Polishing Return Loss LGC-P302/A600SM+R Single Mode 1.0dB or less 40dB or more LGC-P302/A600GI+R Multi Mode Graded Index 0.6dB or less 35dB or more AdPC polishing 9.8 9 12.4 unit(mm) 7.4 33.7 Others Wire wrapping Crimping Soldering 7.2 9.3 IDC Press-in SMT Through hole Optical fiber connector Conversion Adaptor MU-type Conversion adaptor MU-FC type Conversion Adaptor An MU-type plug and an FC-type plug are connectable to each other. Item Number Material of Alignment Sleeve Note Phosphor bronze LGC-A600/A110+R M80.75P unit(mm) 2.2 22 18 HONDA JAPAN 9.8 2-o2.3 1.8 6.6 9.4 3 20.5 180.1 9.9+0.2 0 6.9+0.2 0 2-o2.3 or M2 Hole size (MU side) t=1.6 MU-SC type Conversion Adaptor An MU-type plug and an SC-type plug are connectable to each other. Item Number Note Material of Alignment Sleeve Phosphor bronze LGC-A600/A302+R unit(mm) 180.1 9.9+0.2 0 6.9+0.2 0 9.4 Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 9.8 HONDA JAPAN (2-o2.3 or 2-M2) Hole size (MU side) t=1.6 9.6+0.2 0 1.8 3 1.8 26.7 6.6 180.1 13.3+0.2 0 7.4 18 22 12.8 2 2-o2.3 (2-o2.3 or 2-M2) Hole size (SC side) t=1.6 Optical fiber connector MUJ-type Plug Removing Tool LGC-KP609 Optical fixed attenuator MU-type Tool MUJ-type Plug Removing Tool Item Number Note unit(mm) LGC-KP609 1.1 9.5 16 125 Note 1: This removing tool is a tool to pull out MU-type plugs from a narrow pitch MU-type fixed optical attenuator LGA-S6( )LC+R (Refer to page L-80). Note 2: For high density plug-in type package housing, please use the LGC-KP602C removing tool (Refer to page L-71). Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole