2008-12-04 High Speed PIN Photodiode Schnelle PIN-Fotodiode Version 1.0 SFH 2701 Features: Besondere Merkmale: * Especially suitable for applications from 400 nm to 1050 nm * Fast switching time within the specified wavelength * Ultra short decay time ("slow tail") * IEC Standard 3216 Chipled package * Speziell geeignet fur Anwendungen von 400 nm bis 1050 nm * Sehr kurze Schaltzeit im spezifizierten Wellenlangenbereich * Sehr kurze Schaltzeit bei geringer Sperrspannung (<5V) * Extrem kurze Abklingzeit ("slow tail") * IEC Standard 3216 Chipled Bauform Applications Anwendungen * Fast switching time at low reverse voltage (<5V) * * * * Optical disc drives (CD, DVD) Photointerrupters Industrial electronics For control and drive circuits * * * * Optische Laufwerke (CD, DVD) Lichtschranken Industrieelektronik Messen / Steuern / Regeln Ordering Information Bestellinformation Type: Photocurrent Typ: Fotostrom Ordering Code Bestellnummer 2 = 650 nm, Ee = 0.5 mW/cm , VR = 5 V IP [A] SFH 2701 2008-12-04 1.2 Q65110A2960 1 Version 1.0 SFH 2701 Maximum Ratings (TA = 25 C) Grenzwerte Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Operating and storage temperature range Betriebs- und Lagertemperatur Top; Tstg -40 ... 85 C Reverse voltage Sperrspannung VR 15 V Reverse voltage Sperrspannung (t < 120 s) VR 20 V Electrostatic discharge Elektrostatische Entladung (Human Body Model acc. to EOS/ESD-5.1-1993) VESD 2000 V Characteristics (TA = 25 C) Kennwerte Parameter Symbol Values Werte Unit Bezeichnung Symbol Spectral sensitivity Spektrale Fotoempfindlichkeit ( = 650 nm) S typ 0.45 A/W Spectral sensitivity Spektrale Fotoempfindlichkeit ( = 780 nm) S typ 0.5 A/W Photocurrent Fotostrom ( = 650nm, Ee = 0.5 mW/cm2 ,VR = 5 V) IP 1.2 A Photocurrent Fotostrom ( = 780 nm, Ee = 0.5 mW/cm2 ,VR = 5 V) IP 1.4 A Wavelength of max. sensitivity Wellenlange der max. Fotoempfindlichkeit S max 820 nm Spectral range of sensitivity Spektraler Bereich der Fotoempfindlichkeit 10% 400 ... 1050 nm Radiant sensitive area Bestrahlungsempfindliche Flache A 2008-12-04 2 0.36 Einheit mm2 Version 1.0 SFH 2701 Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Dimensions of radiant sensitive area Abmessung der bestrahlungsempfindlichen Flache LxW Distance from chip front to case surface Abstand von Chipoberflache zu Gehauseoberflache H 0.3 mm Half angle Halbwinkel 60 Dark current Dunkelstrom (VR = 5 V) IR 0.05 ( 5) nA Rise and fall time Schaltzeit (VR = 5 V, RL = 50 , = 650 nm, Ip = 1 mA) tr, tf 1.8 ns Rise and fall time Schaltzeit (VR = 5 V, RL = 50 , = 780 nm, IP = 1 mA) tr, tf 2 ns Forward voltage Durchlassspannung VF 0.8 V Capacitance Kapazitat (VR = 0 V, f = 1 MHz, E = 0) C0 3 ( 5) pF Temperature coefficient of S_650nm Temperaturkoeffizient von S_650nm TCI -0.03 %/K Temperature coefficient of S_780nm Temperaturkoeffizient von S_780nm TCI -0.01 %/K Noise equivalent power Rauschaquivalente Strahlungsleistung (NEP = 17.9 x 10-15 x (IR)1/2/S) (VR = 5 V, = 650 nm) NEP 0.009 pW / Hz1/2 2008-12-04 3 0.6 x 0.6 mm x mm Version 1.0 SFH 2701 Dark Current Dunkelstrom IR = f(VR), E = 0 Relative Spectral Sensitivity Relative spektrale Empfindlichkeit Srel = f() OHF00815 100 % Srel 90 OHF03904 0.12 nA IR 80 70 0.08 60 0.06 50 40 0.04 30 20 0.02 10 0 0 400 500 600 700 800 900 nm 1100 5 0 10 15 Switching Time Schaltzeit Capacitance Kapazitat C = f(VR), f = 1 MHz, E = 0 C V 20 VR tr, tf = f(VR), RL = 50 , = 650 nm, Ip = 200 A OHF03901 4 pF tr , tf 3 OHF03917 8 ns 7 6 5 2 4 3 1 2 1 0 -3 10 10 -2 10 -1 10 0 0 10 1 V 10 2 VR 2008-12-04 0 2 4 6 8 10 12 V 16 VR 4 Version 1.0 SFH 2701 Dark Current Dunkelstrom IR = f(TA), VR = 5V, E = 0 IR OHF03831 102 nA 101 5 100 5 10-1 5 10-2 25 35 45 55 65 75 C 85 TA Directional Characteristics Winkeldiagramm Srel = f() 40 30 20 10 0 OHF01402 1.0 50 0.8 60 0.6 70 0.4 80 0.2 0 90 100 2008-12-04 1.0 0.8 0.6 0.4 0 5 20 40 60 80 100 120 Version 1.0 SFH 2701 Package Outline Mazeichnung 1.65 (0.065) 1.25 (0.049) Cathode mark o0.9 (0.035) 2.15 (0.085) 0.7 (0.028) 2 0.4 (0.016) o0.7 (0.028) GPLY7034 Dimensions in mm (inch). / Mae in mm (inch). Pinning Anschlussbelegung Pin Description Anschluss Beschreibung 1 Cathode 2 Anode Package Chipled (EIA 1206) Gehause Chipled (IEC 3216) 2008-12-04 1.85 (0.073) 3.35 (0.132) 3.05 (0.120) Center of active area 0.92 (0.036) 0.5 (0.020) 1 0.9 (0.035) 1.35 (0.053) 6 Version 1.0 SFH 2701 Recommended Solder Pad Empfohlenes Lotpaddesign 4.7 1.5 1.5 OHF03896 Dimensions in mm. / Mae in mm. Reflow Soldering Profile Reflow-Lotprofil Preconditioning: JEDEC Level 3 acc. to JEDEC J-STD-020D.01 OHA04525 300 C T 250 Tp 245 C 240 C tP 217 C 200 tL 150 tS 100 50 25 C 0 0 50 100 150 200 250 s 300 t 2008-12-04 7 Version 1.0 SFH 2701 OHA04612 Profile Feature Profil-Charakteristik Symbol Symbol Pb-Free (SnAgCu) Assembly Minimum Ramp-up rate to preheat*) 25 C to 150 C Time tS TSmin to TSmax tS 60 Ramp-up rate to peak*) TSmax to TP Recommendation Maximum 2 3 100 120 2 3 Unit Einheit K/s s K/s Liquidus temperature TL 217 Time above liquidus temperature tL 80 100 s Peak temperature TP 245 260 C Time within 5 C of the specified peak temperature TP - 5 K tP 20 30 s 3 6 K/s 10 Ramp-down rate* TP to 100 C 480 Time 25 C to TP All temperatures refer to the center of the package, measured on the top of the component * slope calculation DT/Dt: Dt max. 5 s; fulfillment for the whole T-range 2008-12-04 C 8 s Version 1.0 SFH 2701 Disclaimer Disclaimer Attention please! The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version in the Internet. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components* may only be used in life-support devices** or systems with the express written approval of OSRAM OS. Bitte beachten! Lieferbedingungen und Anderungen im Design vorbehalten. Aufgrund technischer Anforderungen konnen die Bauteile Gefahrstoffe enthalten. Fur weitere Informationen zu gewunschten Bauteilen, wenden Sie sich bitte an unseren Vertrieb. Falls Sie dieses Datenblatt ausgedruckt oder heruntergeladen haben, finden Sie die aktuellste Version im Internet. Verpackung Benutzen Sie bitte die Ihnen bekannten Recyclingwege. Wenn diese nicht bekannt sein sollten, wenden Sie sich bitte an das nachstgelegene Vertriebsburo. Wir nehmen das Verpackungsmaterial zuruck, falls dies vereinbart wurde und das Material sortiert ist. Sie tragen die Transportkosten. Fur Verpackungsmaterial, das unsortiert an uns zuruckgeschickt wird oder das wir nicht annehmen mussen, stellen wir Ihnen die anfallenden Kosten in Rechnung. Bauteile, die in lebenserhaltenden Apparaten und Systemen eingesetzt werden, mussen fur diese Zwecke ausdrucklich zugelassen sein! Kritische Bauteile* durfen in lebenserhaltenden Apparaten und Systemen** nur dann eingesetzt werden, wenn ein schriftliches Einverstandnis von OSRAM OS vorliegt. *) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system. **) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered. *) Ein kritisches Bauteil ist ein Bauteil, das in lebenserhaltenden Apparaten oder Systemen eingesetzt wird und dessen Defekt voraussichtlich zu einer Fehlfunktion dieses lebenserhaltenden Apparates oder Systems fuhren wird oder die Sicherheit oder Effektivitat dieses Apparates oder Systems beeintrachtigt. **) Lebenserhaltende Apparate oder Systeme sind fur (a) die Implantierung in den menschlichen Korper oder (b) fur die Lebenserhaltung bestimmt. Falls Sie versagen, kann davon ausgegangen werden, dass die Gesundheit und das Leben des Patienten in Gefahr ist. 2008-12-04 9 Version 1.0 SFH 2701 Published by OSRAM Opto Semiconductors GmbH Leibnizstrae 4, D-93055 Regensburg www.osram-os.com (c) All Rights Reserved. 2008-12-04 10