M38510/23806BVA - INTEL - Datasheet.Live

REVISIONS

LTR DESCRIPTION DATE (YR-MO-DA) APPROVED

Change ac limits in table I. Add vendor CAGE 18714 to device type 01CX.

Editorial changes throughout.

87-11-18 M. A. Frye

Add device type 02, add case outline E and CAGE code 01295. Made editorial

changes throughout document.

89-10-02 M. A. Frye

Add vendor CAGE F8859. Add device Class V criteria. Add delta limits, table III.

Add case outline X. Update boilerplate. Editorial changes throughout. – lgt

00-11-01 Raymond Monnin

Add section 1.5, radiation features. Add test circuit in figure 4. Update the

boilerplate to include radiation hardness assured requirements. Editorial changes

throughout. - jak

03-12-09 Thomas M. Hess

Add appendix A, microcircuit die. Update the boilerplate to MIL-PRF-38535

requirements and to include radiation hardness assurance requirements. - jak

07-03-08 Thomas M. Hess

CURRENT CAGE CODE 67268

REV

SHEET

REV E E E E E E E

SHEET 15 16 17 18 19 20 21

REV STATUS REV E E E E E E E E E E E E E E

OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14

PMIC N/A

PREPARED BY

Larry T. Gauder

STANDARD

MICROCIRCUIT

DRAWING

CHECKED BY

Monica L. Poelking

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

http://www.dscc.dla.mil

APPROVED BY

Michael A. Frye

THIS DRAWING IS AVAILABLE

FOR USE BY ALL DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

DRAWING APPROVAL DATE

87-05-27

MICROCIRCUIT, DIGITAL, ADVANCED

CMOS, QUAD TWO-INPUT AND GATE,

MONOLITHIC SILICON

AMSC N/A

REVISION LEVEL

SIZE

CAGE CODE

14933

5962-87615

SHEET

1 OF

DSCC FORM 2233

APR 97 5962-E237-07

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

1. SCOPE

1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M)

and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or

Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.

1.2 PIN. The PIN is as shown in the following example:

For device classes M and Q:

5962 - 87615 01 C A

Federal RHA Device Case Lead

stock class designator type outline finish

designator (see 1.2.1) (see 1.2.2) (see 1.2.4) (see 1.2.5)

\ /

Drawing number

For device class V:

5962 F 87615 01 V X A

Federal RHA Device Device Case Lead

stock class designator type class outline finish

designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5)

\ / (see 1.2.3)

Drawing number

1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are

marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A

specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.

1.2.2 Device type(s). The device type(s) identify the circuit function as follows:

Device type Generic number Circuit function

01 54AC08 Quad two-input AND gate

02 54AC11008 Quad two-input AND gate

1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed

below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q

designators will not be included in the PIN and will not be marked on the device.

Device class Device requirements documentation

M Vendor self-certification to the requirements for MIL-STD-883 compliant,

non-JAN class level B microcircuits in accordance with MIL-PRF-38535,

appendix A

Q or V Certification and qualification to MIL-PRF-38535

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:

Outline letter Descriptive designator Terminals Package style

C GDIP1-T14 or CDIP2-T14 14 Dual-in-line

D GDFP1-F14 or CDFP2-F14 14 Flat pack

E GDIP1-T16 or CDIP2-T16 16 Dual-in-line

2 CQCC1-N20 20 Square leadless chip carrier

X CDFP3-F14 14 Flat pack

1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,

appendix A for device class M.

1.3 Absolute maximum ratings. 1/ 2/ 3/

Supply voltage range (VCC) .................................................................................. -0.5 V dc to +7.0 V dc

DC input voltage range (VIN) ................................................................................ -0.5 V dc to VCC + 0.5 V dc

DC output voltage range (VOUT) ........................................................................... -0.5 V dc to VCC + 0.5 V dc

Clamp diode current (IIK, IOK)................................................................................ ±20 mA

DC output current................................................................................................. ±50 mA

DC VCC or GND current (per pin) ......................................................................... ±50 mA

Storage temperature range (TSTG) ....................................................................... -65°C to +150°C

Maximum power dissipation (PD) ........................................................................ 500 mW

Lead temperature (soldering, 10 seconds)........................................................... +260°C

Thermal resistance, junction-to-case (θJC) ........................................................... See MIL-STD-1835

Junction temperature (TJ) ................................................................................... +175°C 4/

1.4 Recommended operating conditions. 2/ 3/ 5/

Supply voltage range (VCC) .................................................................................. +2.0 V dc to +6.0 V dc

Input voltage range (VIN) ...................................................................................... +0.0 V dc to VCC

Output voltage range (VOUT)................................................................................. +0.0 V dc to VCC

Case operating temperature range (TC) ............................................................... -55°C to +125°C

Minimum input rise or fall rate (tr, tf):

CC = 3.6 V ...................................................................................................... 0 to 8 ns

CC = 5.5 V ...................................................................................................... 0 to 8 ns

1.5 Radiation features.

Device type 01:

Total dose (dose rate = 50 – 300 rads (Si)/s) .................................................. 300 krads (Si)

Single Event Latchup (SEL) or Single Event Upset (SEU)............................... ≥ 93 MeV-cm2/mg 6/

1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the

maximum levels may degrade performance and affect reliability.

2/ Unless otherwise noted, all voltages are referenced to GND.

3/ The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of

-55°C to +125°C.

4/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in

accordance with method 5004 of MIL-STD-883.

5/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery back-up systems. Data

retention implies no input transition and no stored data loss with the following conditions: VIH ≥ 70% VCC, VIL ≤ 30% VCC,

OH ≥ 70% VCC at –20 μA, VOL ≤ 30% VCC at 20 μA.

6/ Limits are guaranteed by design or process but not production tested unless specified by the customer through the purchase

order or contract.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part

of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883 - Test Method Standard Microcircuits.

MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 - List of Standard Microcircuit Drawings.

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from

the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein.

Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

ELECTRONIC INDUSTRIES ALLIANCE (EIA)

JEDEC Standard No. 20 - Standard for Description of 54/74ACXXXX and 54/74ACTXXXX Advanced High-Speed

CMOS Devices.

(Copies of this document is available online at www.eia.org/ or from the Electronics Industries Alliance, 2500 Wilson

Boulevard, Arlington, VA 22201-3834).

AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)

ASTM F1192 - Standard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion

Irradiation of semiconductor Devices.

(Copies of these documents are available online at http://www.astm.org or from ASTM International, 100 Barr Harbor Drive,

P.O. Box C700, West Conshohocken, PA 19428-2959).

2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of

this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with

MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The

modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for

device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified

herein.

3.1.1 Microcircuit die. For the requirements of microcircuit die, see appendix A to this document.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in

MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.

3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.

3.2.3 Truth table. The truth table shall be as specified on figure 2.

3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3.

3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4.

3.2.6 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document

revision level control and shall be made available to the preparing or acquiring activity upon request.

3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the

electrical performance characteristics and postirradiation parameter limits are as specified in table IA and shall apply over the full

case operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical

tests for each subgroup are defined in table IA.

3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be

marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer

has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be

marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be

in accordance with MIL-PRF-38535, appendix A.

3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in

MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.

3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535

listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of

compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see

6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this

drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and

herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.

3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for

device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.

3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2

herein) involving devices acquired to this drawing is required for any change that affects this drawing.

3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the

option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made

available onshore at the option of the reviewer.

3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in

microcircuit group number 36 (see MIL-PRF-38535, appendix A).

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

TABLE IA. Electrical performance characteristics.

Limits 4/ Test and

MIL-STD-883

test method 1/

Symbol Test conditions 2/ 3/

-55°C ≤ TC ≤ +125°C

+3.0 V ≤ VCC ≤ +5.5 V

Unless otherwise specified

Device

type

and

Device

class

VCC Group A

subgroups

Min Max

Unit

Positive input

clamp voltage

3022

VIC+ For input under test, IIN = 1.0 mA All

Q, V

0.0 V 1 0.4 1.5 V

Negative input

clamp voltage

3022

VIC- For input under test, IIN = -1.0 mA All

Q, V

Open 1 -0.4 -1.5 V

3.0 V 2.9

4.5 V 4.4

VIN = VIH minimum or VIL maximum

IOH = -50 μA

All

5.5 V

1, 2, 3

5.4

2, 3 2.4 VIN = VIH minimum or VIL maximum

IOH = -12 mA

All

3.0 V

1 2.56

2, 3 3.7 4.5 V

1 3.86

2, 3 4.7

VIN = VIH minimum or VIL maximum

IOH = -24 mA

All

5.5 V

1 4.86

High level output

voltage

3006

VOH

VIN = VIH minimum or VIL maximum

IOH = -50 mA

All

5.5 V 1, 2, 3 3.85

3.0 V 0.1

4.5 V 0.1

VIN = VIH minimum or VIL maximum

IOL = 50 μA

All

5.5 V

1, 2, 3

0.1

2, 3 0.5 VIN = VIH minimum or VIL maximum

IOL = 12 mA

All

3.0 V

1 0.36

2, 3 0.5 4.5 V

1 0.36

2, 3 0.5

VIN = VIH minimum or VIL maximum

IOL = 24 mA

All

5.5 V

1 0.36

Low level output

voltage

3007

VOL

VIN = VIH minimum or VIL maximum

IOL = 50 mA

All

5.5 V 1, 2, 3 1.65

3.0 V 2.1

4.5 V 3.15

High level input

voltage

VIH

All

5.5 V

1, 2, 3

3.85

3.0 V 0.9

4.5 V 1.35

Low level input

voltage

VIL

All

5.5 V

1, 2, 3

1.65

See footnotes at end of table.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

TABLE IA. Electrical performance characteristics – Continued.

Limits 4/ Test and

MIL-STD-883

test method 1/

Symbol Test conditions 2/ 3/

-55°C ≤ TC ≤ +125°C

+3.0 V ≤ VCC ≤ +5.5 V

Unless otherwise specified

Device

type

and

Device

class

VCC Group A

subgroups

Min Max

Unit

1 -0.1 Input leakage

current low

3009

IIL V

IN = 0.0 V All

All

5.5 V

2, 3 -1.0

μA

1 0.1 Input leakage

current high

3010

IIH V

IN = 5.5 V All

All

5.5 V

2, 3 1.0

μA

1 2.0 VIN = VCC or GND

IOUT = 0 A

All

All 2, 3 40

Quiescent supply

current, output

high

3005

ICCH

M, D, P, L, R, F

Q, V

5.5 V

1 50

μA

1 2.0 VIN = VCC or GND

IOUT = 0 A

All

All 2, 3 40

Quiescent supply

current, output

low

3005

ICCL

M, D, P, L, R, F

Q, V

5.5 V

1 50

μA

Input capacitance

3012

CIN See 4.4.1c

TC = +25°C

All

5.0 V 4 10.0 pF

Power dissipation

capacitance

CPD

See 4.4.1c

TC = +25°C, f = 1 MHz

All

5.0 V 4 88.0 pF

3.0 V 7, 8 L H Functional tests

3014

VIN = VIH or VIL

Verify output VOUT

See 4.4.1b

All

5.5 V 7, 8 L H

Propagation delay

time, high to low

low to high,

mA or mB to mY

tPHL

10/

TC = +25°C

CL = 50 pF minimum

RL = 500Ω

See figure 4

All

3.0 V 9 1.0

9.0

3003 All

All

4.5 V 1.5

7.0

PLH All

All

3.0 V 1.0

10.0

10/ All

All

4.5 V 1.5

7.5

PHL

10/

TC = -55°C and +125°C

CL = 50 pF minimum

RL = 500Ω

See figure 4

All

3.0 V 10, 11 1.0

11.5

All

4.5 V 1.0

8.5

PLH All

All

3.0 V 1.0

12.5

10/ All

All

4.5 V 1.0

9.0

See footnotes on next sheet.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

TABLE IA. Electrical performance characteristics – Continued.

1/ For tests not listed in the referenced MIL-STD-883, [e.g. VIH, VIL], utilize the general test procedure under the conditions

listed herein.

2/ Each input/output, as applicable, shall be tested at the specified temperature, for the specified limits, to the tests in table IA

herein. Output terminals not designated shall be high level logic, low level logic, or open, except as follows:

a. VIC (pos) tests, the GND terminal can be open. TC = +25°C.

b. VIC (neg) tests, the VCC terminal shall be open. TC = +25°C.

c. All ICC tests, the output terminal shall be open. When performing these tests, the current meter shall be placed in the

circuit such that all current flows through the meter.

3/ RHA parts supplied to this drawing have been characterized through all levels M, D, P, L, R, and F of irradiation. However,

this device is only tested at the 'F' level. Pre and Post irradiation values are identical unless otherwise specified in table IA.

When performing post irradiation electrical measurements for any RHA level, TA = +25°C.

4/ For negative and positive voltage and current values, the sign designates the potential difference in reference to GND and

the direction of current flow, respectively; and the absolute value of the magnitude, not the sign, is relative to the minimum

and maximum limits, as applicable, listed herein. All devices shall meet or exceed the limits specified in table IA, as

applicable, at 3.0 V ≤ VCC ≤ 3.6 V and 4.5 V ≤ VCC ≤ 5.5 V.

5/ The VOH and VOL tests shall be tested at VCC = 3.0 V and 4.5 V. The VOH and VOL tests are guaranteed, if not tested, for

other values of VCC. Limits shown apply to operation at VCC = 3.3 V ±0.3 V and VCC = 5.0 V ±0.5 V. Tests with input current

at +50 mA or -50 mA are performed on only one input at a time with duration not to exceed 2 ms. Transmission driving tests

may be performed using VIN = VCC or GND. When VIN = VCC or GND is used, the test is guaranteed for

IN = VIH minimum and VIL maximum.

6/ The VIH and VIL tests are not required if applied as forcing functions for VOH and VOL tests.

7/ The maximum limit for this parameter at 100 krads (Si) is 2 μA.

8/ Power dissipation capacitance (CPD) determines both the power consumption (PD) and dynamic current consumption (IS).

Where:

D = (CPD + CL) (VCC x VCC)f + (ICC x VCC)

S = (CPD + CL) VCCf + ICC

f is the frequency of the input signal and CL is the external output load capacitance.

9/ Tests shall be performed in sequence, attributes data only. Functional tests shall include the truth table and other logic

patterns used for fault detection. The test vectors used to verify the truth table shall, at a minimum, test all functions of

each input and output. All possible input to output logic patterns per function shall be guaranteed, if not tested, to the truth

table in figure 2 herein. Functional tests shall be performed in sequence as approved by the qualifying activity on qualified

devices. Allowable tolerances in accordance with MIL-STD-883 for the input voltage levels may be incorporated. For VOUT

measurements, L ≤ 0.3VCC and H ≥ 0.7VCC.

10/ For propagation delay tests, all paths must be tested. AC limits at VCC = 5.5 V are equal to the limits at VCC = 4.5 V and

guaranteed by testing at VCC = 4.5 V. AC limits at VCC = 3.6 V are equal to limits at VCC = 3.0 V and guaranteed by testing at

VCC = 3.0 V. Minimum ac limits for VCC = 5.5 V are 1.0 ns and guaranteed by guardbanding the VCC = 4.5 V minimum limits

to 1.5 ns.

TABLE IB. SEP test limits. 1/ 2/

Device

type

SEP TC =

temperature

±10°C

VCC

Effective LET

01 SEL and SEU +25°C 3.6 V and 5.5 V ≥ 93 MeV-cm2/mg

1/ For SEP test conditions, see 4.4.4.2 herein.

2/ Technology characterization and model verification supplemented by in-line data may be used in lieu of end-of-

line testing. Test plan must be approved by TRB and qualifying activity.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

Device types 01 02

Case outlines

C, D, and X 2 E 2

Terminal

number

Terminal symbol

1 1A NC 1A NC

2 1B 1A 1Y VCC

3 1Y 1B 2Y 2B

4 2A 1Y GND 2A

5 2B NC GND 1B

6 2Y 2A 3Y NC

7 GND NC 4Y 1A

8 3Y 2B 4B 1Y

9 3A 2Y 4A 2Y

10 3B GND 3B GND

11 4Y NC 3A NC

12 4A 3Y VCC GND

13 4B 3A VCC 3Y

14 VCC 3B 2B 4Y

15 --- NC 2A 4B

16 --- 4Y 1B NC

17 --- NC --- 4A

18 --- 4A --- 3B

19 --- 4B --- 3A

20 --- VCC --- VCC

NC = no connection

FIGURE 1. Terminal connections.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

(Each gate)

Input

Output

L L L

H L L

L H L

H H H

L = Low voltage level

H = High voltage level

FIGURE 2. Truth table.

FIGURE 3. Logic diagram.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

FROM OUTPUT UNDER TEST

NOTES:

1. VTEST = open for tPLH and tPHL.

2. CL = 50 pF or equivalent (includes probe and jig capacitance).

3. RL = 500Ω or equivalent.

4. Input signal from pulse generator: VIN = 0.0 V to VCC; PRR ≤ 1 MHz; ZO = 50Ω; tr ≤ 3.0 ns; tf ≤ 3.0 ns;

tr and tf shall be measured from 10% of VCC to 90% of VCC and from 90% of VCC to 10% of VCC, respectively;

duty cycle = 50 percent.

5. Timing parameters shall be tested at a minimum input frequency of 1MHz.

6. The outputs are measured one at a time with one transition per measurement.

FIGURE 4. Switching waveforms and test circuit.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

4. VERIFICATION

4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with

MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan

shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in

accordance with MIL-PRF-38535, appendix A.

4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted

on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in

accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection.

4.2.1 Additional criteria for device class M.

a. Burn-in test, method 1015 of MIL-STD-883.

(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision

level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall

specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in

test method 1015 of MIL-STD-883.

(2) TA = +125°C, minimum.

b. Interim and final electrical test parameters shall be as specified in table IIA herein.

4.2.2 Additional criteria for device classes Q and V.

a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the

device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained

under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance

with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit

shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified

in test method 1015 of MIL-STD-883.

b. Interim and final electrical test parameters shall be as specified in table IIA herein.

c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in

MIL-PRF-38535, appendix B.

4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in

accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups

A, B, C, D, and E inspections (see 4.4.1 through 4.4.4).

4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with

MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified herein. Quality conformance inspection for

device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed

for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections

(see 4.4.1 through 4.4.4).

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

TABLE IIA. Electrical test requirements.

Test requirements Subgroups

(in accordance with

MIL-STD-883, method

5005, table I)

Subgroups

(in accordance with

MIL-PRF-38535, table III)

Device

class M

Device

class Q

Device

class V

Interim electrical

parameters (see 4.2)

- - - - - - 1

Final electrical

parameters (see 4.2)

1/ 1, 2, 3, 7,

8, 9

1/ 1, 2, 3, 7,

8, 9

2/ 3/ 1, 2, 3, 7,

8, 9

Group A test

requirements (see 4.4)

1, 2, 3, 4, 7,

8, 9, 10, 11

1, 2, 3, 4, 7,

8, 9, 10, 11

1, 2, 3, 4, 7,

8, 9, 10, 11

Group C end-point electrical

parameters (see 4.4)

1, 2, 3 1, 2, 3 3/ 1, 2, 3, 7,8,

9, 10, 11

Group D end-point electrical

parameters (see 4.4)

1, 2, 3 1, 2, 3 1, 2, 3

Group E end-point electrical

parameters (see 4.4)

1, 7, 9 1, 7, 9 1, 7, 9

1/ PDA applies to subgroup 1.

2/ PDA applies to subgroups 1, 7, and deltas.

3/ Delta limits, as specified in table IIB, shall be required where specified, and the delta limits shall be

completed with reference to the zero hour electrical parameters.

TABLE IIB. Burn-in and operating life test delta parameters (+25°C). 1/

Parameter 2/ Symbol Delta Limits

Quiescent supply current ICCH, ICCL ±150 nA

Input current low level IIL ±20 nA

Input current high level IIH ±20 nA

Output voltage low level

(VCC = 5.5 V, IOL = 24 mA)

VOL ±0.04 V

Output voltage high level

(VCC = 5.5 V, IOH = -24 mA)

VOH ±0.2 V

1/ This table is representation of what vendor CAGE F8859 has

experienced and is guaranteed and not meant to be construed

as a quality assurance requirement for any other vendor.

2/ These parameters shall be recorded before and after the required

burn-in and life tests to determine the delta limits.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

4.4.1 Group A inspection.

a. Tests shall be as specified in table IIA herein.

b. For device class M, subgroups 7 and 8 tests shall be sufficient to verify the truth table in figure 2 herein. The test

vectors used to verify the truth table shall, at a minimum, test all functions of each input and output. All possible input

to output logic patterns per function shall be guaranteed, if not tested, to the truth table in figure 2, herein. For device

classes Q and V, subgroups 7 and 8 shall include verifying the functionality of the device.

c. CIN and CPD shall be measured only for initial qualification and after process or design changes which may affect

capacitance. CIN shall be measured between the designated terminal and GND at a frequency of 1 MHz. CPD shall be

tested in accordance with the latest revision of JEDEC Standard No. 20 and table IA herein. For CIN and CPD, test all

applicable pins on five devices with zero failures.

4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein.

4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:

a. Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level

control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify

the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method

1005 of MIL-STD-883.

b. TA = +125°C, minimum.

c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.

4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature,

or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The

test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with

MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the

inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of

MIL-STD-883.

4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein.

4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured

(see 3.5 herein).

a. End-point electrical parameters shall be as specified in table IIA herein.

b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as

specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to

radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device

classes must meet the post irradiation end-point electrical parameter limits as defined in table IA at

A = +25°C +5°C, after exposure, to the subgroups specified in table IIA herein.

4.4.4.1 Total dose irradiation testing. Total dose irradiation testing shall be performed in accordance with MIL-STD-883

method 1019, condition A, and as specified herein.

4.4.4.1.1 Accelerated annealing test. Accelerated annealing tests shall be performed on all devices requiring a RHA level

greater than 5k rads (Si). The post-anneal end-point electrical parameter limits shall be as specified in table IA herein and shall

be the pre-irradiation end-point electrical parameter limit at 25°C ±5°C. Testing shall be performed at initial qualification and

after any design or process changes which may affect the RHA response of the device.

4.4.4.2 Single event phenomena (SEP). When specified in the purchase order or contract, SEP testing shall be required on

class V devices. SEP testing shall be performed on the Standard Evaluation Circuit (SEC) or alternate SEP test vehicle as

approved by the qualifying activity at initial qualification and after any design or process changes which may affect the upset or

latchup characteristics. Test four devices with zero failures. ASTM F1192 may be used as a guideline when performing SEP

testing. The test conditions for SEP are as follows:

a. The ion beam angle of incidence shall be between normal to the die surface and 60° to the normal, inclusive

(i.e. 0° ≤ angle ≤ 60°). No shadowing of the ion beam due to fixturing or package related effects is allowed.

b. The fluence shall be ≥ 100 errors or ≥ 107 ions/cm2.

c. The flux shall be between 102 and 105 ions/cm2/s. The cross-section shall be verified to be flux independent by

measuring the cross-section at two flux rates which differ by at least an order of magnitude.

d. The particle range shall be ≥ 20 microns in silicon.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

e. The upset test temperature shall be +25°C and the latchup test temperature is maximum rated operating temperature

±10°C.

f. Bias conditions shall be defined by the manufacturer for latchup measurements.

g. For SEP test limits, see table IB herein.

4.5 Methods of inspection. Methods of inspection shall be specified as follows:

4.5.1 Voltage and current. Unless otherwise specified, all voltages given are referenced to the microcircuit GND terminal.

Currents given are conventional current and positive when flowing into the referenced terminal.

5. PACKAGING

5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes

Q and V or MIL-PRF-38535, appendix A for device class M.

6. NOTES

6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications

(original equipment), design applications, and logistics purposes.

6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-

prepared specification or drawing.

6.1.2 Substitutability. Device class Q devices will replace device class M devices.

6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for

the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.

6.3 Record of users. Military and industrial users should inform Defense Supply Center Columbus (DSCC) when a system

application requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users

and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic

devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544.

6.4 Comments. Comments on this drawing should be directed to DSCC-VA , Columbus, Ohio 43218-3990, or telephone

(614) 692-0547.

6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in

MIL-PRF-38535 and MIL-HDBK-1331.

6.6 Sources of supply.

6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535.

The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have agreed to

this drawing.

6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103.

The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been

submitted to and accepted by DSCC-VA.

6.7 Additional information. When specified in the purchase order or contract, a copy of the following additional data shall be

supplied.

a. RHA upset levels.

b. Test conditions (SEP).

c. Number of upsets (SEP).

d. Number of transients (SEP).

e. Occurrence of latch-up (SEP).

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

APPENDIX A

APPENDIX A FORMS A PART OF SMD 5962-87615

A.1 SCOPE

A.1.1 Scope. This appendix establishes minimum requirements for microcircuit die to be supplied under the Qualified

Manufacturers List (QML) Program. QML microcircuit die meeting the requirements of MIL-PRF-38535 and the manufacturers

approved QM plan for use in monolithic microcircuits, multi-chip modules (MCMs), hybrids, electronic modules, or devices using

chip and wire designs in accordance with MIL-PRF-38534 are specified herein. Two product assurance classes consisting of

military high reliability (device class Q) and space application (device class V) are reflected in the Part or Identification Number

(PIN). When available, a choice of Radiation Hardiness Assurance (RHA) levels are reflected in the PIN.

A.1.2 PIN. The PIN is as shown in the following example:

5962 F 87615 01 V 9 A

Federal RHA Device Device Die Die

stock class designator type class code details

designator (see A.1.2.1) (see A.1.2.2) designator (see A.1.2.4)

\ / (see A.1.2.3)

Drawing number

A.1.2.1 RHA designator. Device classes Q and V RHA identified die meet the MIL-PRF-38535 specified RHA levels. A dash

(-) indicates a non-RHA die.

A.1.2.2 Device type(s). The device type(s) identify the circuit function as follows:

Device type Generic number Circuit function

01 54AC08 Quad 2-input AND gate

A.1.2.3 Device class designator. Device class Q designator will not be included in the PIN and will not be marked on the

device since the device class designator has been added after the original issuance of this drawing.

Device class Device requirements documentation

Q or V Certification and qualification to the die requirements of MIL-PRF-38535

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

APPENDIX A

APPENDIX A FORMS A PART OF SMD 5962-87615

A.1.2.4 Die details. The die details designation is a unique letter which designates the die's physical dimensions, bonding pad

location(s) and related electrical function(s), interface materials, and other assembly related information, for each product and

variant supplied to this appendix.

A.1.2.4.1 Die physical dimensions.

Die type Figure number

01 A-1

A.1.2.4.2 Die bonding pad locations and electrical functions.

Die type Figure number

01 A-1

A.1.2.4.3 Interface materials.

Die type Figure number

01 A-1

A.1.2.4.4 Assembly related information.

Die type Figure number

01 A-1

A.1.3 Absolute maximum ratings. See paragraph 1.3 herein for details.

A.1.4 Recommended operating conditions. See paragraph 1.4 herein for details.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

APPENDIX A

APPENDIX A FORMS A PART OF SMD 5962-87615

A.2. APPLICABLE DOCUMENTS

A.2.1 Government specification, standards, and handbooks. The following specification, standard, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in

the solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE STANDARD

MIL-STD-883 - Test Method Standard Microcircuits.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 - List of Standard Microcircuit Drawings.

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from

the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

A.2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

A.3 REQUIREMENTS

A.3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with

MIL-PRF-38535 and as specified herein or as modified in the device manufacturer’s Quality Management (QM) plan. The

modification in the QM plan shall not affect the form, fit, or function as described herein.

A.3.2 Design, construction and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38535 and herein and the manufacturer’s QM plan for device classes Q and V.

A.3.2.1 Die physical dimensions. The die physical dimensions shall be as specified in A.1.2.4.1 and on figure A-1.

A.3.2.2 Die bonding pad locations and electrical functions. The die bonding pad locations and electrical functions shall be as

specified in A.1.2.4.2 and on figure A-1.

A.3.2.3 Interface materials. The interface materials for the die shall be as specified in A.1.2.4.3 and on figure A-1.

A.3.2.4 Assembly related information. The assembly related information shall be as specified in A.1.2.4.4 and on figure A-1.

A.3.2.5 Truth table. The truth table shall be as defined in paragraph 3.2.3 herein.

A.3.2.6 Radiation exposure circuit. The radiation exposure circuit shall be as defined in paragraph 3.2.6 herein.

A.3.3 Electrical performance characteristics and post-irradiation parameter limits. Unless otherwise specified herein, the

electrical performance characteristics and post-irradiation parameter limits are as specified in table IA of the body of this

document.

A.3.4 Electrical test requirements. The wafer probe test requirements shall include functional and parametric testing sufficient

to make the packaged die capable of meeting the electrical performance requirements in table IA.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

APPENDIX A

APPENDIX A FORMS A PART OF SMD 5962-87615

A.3.5 Marking. As a minimum, each unique lot of die, loaded in single or multiple stack of carriers, for shipment to a

customer, shall be identified with the wafer lot number, the certification mark, the manufacturer’s identification and the PIN listed

in A.1.2 herein. The certification mark shall be a “QML” or “Q” as required by MIL-PRF-38535.

A.3.6 Certification of compliance. For device classes Q and V, a certificate of compliance shall be required from a

QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see A.6.4 herein). The certificate of

compliance submitted to DSCC-VA prior to listing as an approved source of supply for this appendix shall affirm that the

manufacturer’s product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and the requirements herein.

A.3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535

shall be provided with each lot of microcircuit die delivered to this drawing.

A.4 VERIFICATION

A.4.1 Sampling and inspection. For device classes Q and V, die sampling and inspection procedures shall be in accordance

with MIL-PRF-38535 or as modified in the device manufacturer’s Quality Management (QM) plan. The modifications in the QM

plan shall not affect the form, fit, or function as described herein.

A.4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and as defined in the

manufacturer’s QM plan. As a minimum, it shall consist of:

a. Wafer lot acceptance for class V product using the criteria defined in MIL-STD-883, method 5007.

b. 100% wafer probe (see paragraph A.3.4 herein).

c. 100% internal visual inspection to the applicable class Q or V criteria defined in MIL-STD-883, method 2010 or the

alternate procedures allowed in MIL-STD-883, method 5004.

A.4.3 Conformance inspection.

A.4.3.1 Group E inspection. Group E inspection is required only for parts intended to be identified as radiation assured (see

A.3.5 herein). RHA levels for device classes Q and V shall be as specified in MIL-PRF-38535. End point electrical testing of

packaged die shall be as specified in table II herein. Group E tests and conditions are as specified in paragraphs 4.4.4 herein.

A.5 DIE CARRIER

A.5.1 Die carrier requirements. The requirements for the die carrier shall be accordance with the manufacturer’s QM plan or

as specified in the purchase order by the acquiring activity. The die carrier shall provide adequate physical, mechanical and

electrostatic protection.

A.6 NOTES

A.6.1 Intended use. Microcircuit die conforming to this drawing are intended for use in microcircuits built in accordance with

MIL-PRF-38535 or MIL-PRF-38534 for government microcircuit applications (original equipment), design applications, and

logistics purposes.

A.6.2 Comments. Comments on this appendix should be directed to DSCC-VA, P.O. Box 3990, Columbus, Ohio,

43218-3990 or telephone (614) 692-0547.

A.6.3 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in

MIL-PRF-38535 and MIL-HDBK-1331.

A.6.4 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535.

The vendors listed within QML-38535 have submitted a certificate of compliance (see A.3.6 herein) to DSCC-VA and have

agreed to this drawing.

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

APPENDIX A

APPENDIX A FORMS A PART OF SMD 5962-87615

Die physical dimensions.

Die size: 1991 x 1281 μm

Die thickness: 285 ±25 μm

Die bonding pad locations and electrical functions.

Optional manufacturer's logo

Pad size: Pad numbers 1 to 6 and 8 to 13: 100 x 100 μm

Pad numbers 7 (GND) and 14 (VCC): 100 x 280 μm

NOTE: Pad numbers reflect terminal numbers when placed in case outline X (see figure 1).

FIGURE A-1

SIZE

5962-87615

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

APPENDIX A

APPENDIX A FORMS A PART OF SMD 5962-87615

Interface materials.

Top metallization: Al Si Cu 0.85 μm

Backside metallization: None

Glassivation.

Type: P. Vapox + Nitride

Thickness: 5000Å – 7000Å

Substrate: Silicon

Assembly related information.

Substrate potential: Floating or tied to GND

Special assembly instructions: Bond pad #14 (VCC) first

FIGURE A-1 – Continued.

STANDARD MICROCIRCUIT DRAWING BULLETIN

DATE: 07-03-07

Approved sources of supply for SMD 5962-87615 are listed below for immediate acquisition information only and shall be added to

MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or

deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to

and accepted by DSCC-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535.

DSCC maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.

Standard

microcircuit drawing

PIN 1/

Vendor

CAGE

number

Vendor

Similar

PIN 2/

5962-8761501CA

27014

01295

0C7V7

54AC08DMQB

SNJ54AC08J

54AC08DMQB

5962-8761501DA

27014

01295

0C7V7

54AC08FMQB

SNJ54AC08W

54AC08FMQB

5962-87615012A

27014

01295

0C7V7

54AC08LMQB

SNJ54AC08FK

54AC08LMQB

5962-8761502EA 3V146 54AC11008J

5962-87615022A 3V146 54AC11008FK

5962-8761501XA 3/ 54AC08K02Q

5962-8761501VXA 3/ 54AC08K02V

5962-8761501XC 3/ 54AC08K01Q

5962-8761501VXC 3/ 54AC08K01V

5962F8761501XA F8859 RHFAC08K02Q

5962F8761501VXA F8859 RHFAC08K02V

5962F8761501XC F8859 RHFAC08K01Q

5962F8761501VXC F8859 RHFAC08K01V

5962F8761501CA F8859 RHFAC08D04Q

5962F8761501CC F8859 RHFAC08D03Q

5962F8761501VCA F8859 RHFAC08D04V

5962F8761501VCC F8859 RHFAC08D03V

5962F8761501V9A F8859 AC08DIE2V

/ The lead finish shown for each PIN representing a hermetic

package is the most readily available from the manufacturer

listed for that part. If the desired lead finish is not listed,

contact the vendor to determine its availability.

/ Caution. Do not use this number for item acquisition. Items

acquired to this number may not satisfy the performance

requirements of this drawing.

/ Not available from an approved source of supply.

Sheet 1 of 2

STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued

Vendor CAGE Vendor name

number and address

27014 National Semiconductor

2900 Semiconductor Drive

P.O. Box 58090

Santa Clara, CA 95052-8090

F8859 ST Microelectronics

3 rue de Suisse

CS 60816

35208 RENNES cedex2-FRANCE

01295 Texas Instruments Incorporated

Semiconductor Group

8505 Forest Lane

P.O. Box 660199

Dallas, TX 75243

Point of contact: U.S. Highway 75 South

P.O. Box 84, M/S 853

Sherman, TX 75090-9493

3V146 Rochester Electronics

16 Malcolm Hoyt Drive

Newburyport, MA 01950

0C7V7 QP Semiconductor

2945 Oakmead Village Court

Santa Clara, CA 95051

The information contained herein is disseminated for convenience only and the

Government assumes no liability whatsoever for any inaccuracies in the

information bulletin.

Sheet 2 of 2