Characteristic / Test Conditions
Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA)
On State Drain Current 2 (VDS > ID(on) x RDS(on) Max, VGS = 10V)
Drain-Source On-State Resistance 2 (VGS = 10V, 0.5 ID[Cont.])
Zero Gate Voltage Drain Current (VDS = VDSS, VGS = 0V)
Zero Gate Voltage Drain Current (VDS = 0.8 VDSS, VGS = 0V, TC = 125°C)
Gate-Source Leakage Current (VGS = ±30V, VDS = 0V)
Gate Threshold Voltage (VDS = VGS, ID = 1.0mA)
050-5568 Rev B
MAXIMUM RATINGS All Ratings: TC = 25°C unless otherwise specified.
Symbol
VDSS
ID
IDM
VGS
VGSM
PD
TJ,TSTG
TL
IAR
EAR
EAS
Parameter
Drain-Source Voltage
Continuous Drain Current @ TC = 25°C
Pulsed Drain Current 1
Gate-Source Voltage Continuous
Gate-Source Voltage Transient
Total Power Dissipation @ TC = 25°C
Linear Derating Factor
Operating and Storage Junction Temperature Range
Lead Temperature: 0.063" from Case for 10 Sec.
Avalanche Current 1 (Repetitive and Non-Repetitive)
Repetitive Avalanche Energy 1
Single Pulse Avalanche Energy 4
UNIT
Volts
Amps
Volts
Watts
W/°C
°C
Amps
mJ
STATIC ELECTRICAL CHARACTERISTICS
Symbol
BVDSS
ID(on)
RDS(on)
IDSS
IGSS
VGS(th)
UNIT
Volts
Amps
Ohms
µA
nA
Volts
MIN TYP MAX
200
56 0.045
250
1000
±100
24
APT20M45SVFR
200
56
224
±30
±40
300
2.4
-55 to 150
300
56
30
1300
APT20M45SVFR
200V 56A 0.045Ω
FREDFET
G
D
S
Power MOS V® is a new generation of high voltage N-Channel enhancement
mode power MOSFETs. This new technology minimizes the JFET effect,
increases packing density and reduces the on-resistance. Power MOS V®
also achieves faster switching speeds through optimized gate layout.
• Fast Recovery Body Diode • 100% Avalanche Tested
• Lower Leakage • Surface Mount D3PAK Package
• Faster Switching
FREDFET
POWER MOS V®
CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed.
USA
405 S.W. Columbia Street Bend, Oregon 97702-1035 Phone: (541) 382-8028 FAX: (541) 388-0364
EUROPE
Avenue J.F. Kennedy Bât B4 Parc Cadéra Nord F-33700 Merignac - France Phone: (33) 55792 1515 FAX: (33) 5 56 47 97 61
APT Website - http://www.advancedpower.com
D
3
PAK
DYNAMIC CHARACTERISTICS APT20M45SVFR
050-5568 Rev B
ZθJC, THERMAL IMPEDANCE (°C/W)
10-5 10-4 10-3 10-2 10-1 1.0 10
RECTANGULAR PULSE DURATION (SECONDS)
FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION
0.5
0.1
0.05
0.01
0.005
0.001
Note:
Duty Factor D = t1/t2
Peak TJ = PDM x ZθJC + TC
t1
t2
PDM
0.1
SINGLE PULSE
0.02
0.05
0.2
D=0.5
0.01
SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS
Characteristic / Test Conditions
Continuous Source Current (Body Diode)
Pulsed Source Current 1 (Body Diode)
Diode Forward Voltage 2 (VGS = 0V, IS = -ID [Cont.])
Peak Diode Recovery dv/dt 5
Reverse Recovery Time
(IS = -ID [Cont.], di/dt = 100A/µs)
Reverse Recovery Charge
(IS = -ID [Cont.], di/dt = 100A/µs)
Peak Recovery Current
(IS = -ID [Cont.], di/dt = 100A/µs)
Symbol
IS
ISM
VSD
dv/dt
trr
Qrr
IRRM
UNIT
Amps
Volts
V/ns
ns
µC
Amps
Symbol
Ciss
Coss
Crss
Qg
Qgs
Qgd
td(on)
tr
td(off)
tf
Characteristic
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Total Gate Charge 3
Gate-Source Charge
Gate-Drain ("Miller") Charge
Turn-on Delay Time
Rise Time
Turn-off Delay Time
Fall Time
Test Conditions
VGS = 0V
VDS = 25V
f = 1 MHz
VGS = 10V
VDD = 0.5 VDSS
ID = ID [Cont.] @ 25°C
VGS = 15V
VDD = 0.5 VDSS
ID = ID [Cont.] @ 25°C
RG = 1.6Ω
MIN TYP MAX
4050 4860
980 1375
300 450
130 195
30 45
55 80
12 24
14 28
43 70
714
UNIT
pF
nC
ns
MIN TYP MAX
56
224
1.3
5
Tj = 25°C200
Tj = 125°C300
Tj = 25°C0.7
Tj = 125°C2.4
Tj = 25°C10
Tj = 125°C18
1Repetitive Rating: Pulse width limited by maximum junction 3See MIL-STD-750 Method 3471
temperature. 4Starting Tj = +25°C, L = 0.83mH, RG = 25Ω, Peak IL = 56A
2Pulse Test: Pulse width < 380 µS, Duty Cycle < 2% 5IS ≤ -ID [Cont.], di/dt = 100A/µs, VDD ≤ VDSS, Tj ≤ 150°C, RG = 2.0Ω,
VR = 200V.
APT Reserves the right to change, without notice, the specifications and information contained herein.
THERMAL CHARACTERISTICS
Symbol
RθJC
RθJA
MIN TYP MAX
0.42
40
UNIT
°C/W
Characteristic
Junction to Case
Junction to Ambient
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
FIGURE 2, TYPICAL OUTPUT CHARACTERISTICS FIGURE 3, TYPICAL OUTPUT CHARACTERISTICS
VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) ID, DRAIN CURRENT (AMPERES)
FIGURE 4, TYPICAL TRANSFER CHARACTERISTICS FIGURE 5, RDS(ON) vs DRAIN CURRENT
TC, CASE TEMPERATURE (°C) TJ, JUNCTION TEMPERATURE (°C)
FIGURE 6, MAXIMUM DRAIN CURRENT vs CASE TEMPERATURE FIGURE 7, BREAKDOWN VOLTAGE vs TEMPERATURE
TJ, JUNCTION TEMPERATURE (°C) TC, CASE TEMPERATURE (°C)
FIGURE 8, ON-RESISTANCE vs. TEMPERATURE FIGURE 9, THRESHOLD VOLTAGE vs TEMPERATURE
RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE ID, DRAIN CURRENT (AMPERES) ID, DRAIN CURRENT (AMPERES) ID, DRAIN CURRENT (AMPERES)
(NORMALIZED)
VGS(TH), THRESHOLD VOLTAGE BVDSS, DRAIN-TO-SOURCE BREAKDOWN RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE ID, DRAIN CURRENT (AMPERES)
(NORMALIZED) VOLTAGE (NORMALIZED)
020406080100 0 2 4 6 8 10
02468 04080120160200
25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150
-50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150
APT20M45SVFR
ID = 0.5 ID [Cont.]
VGS = 10V
100
80
60
40
20
0
1.6
1.4
1.2
1.0
0.8
1.15
1.10
1.05
1.00
0.95
0.90
1.2
1.1
1.0
0.9
0.8
0.7
0.6
100
80
60
40
20
0
100
80
60
40
20
0
60
50
40
30
20
10
0
2.5
2.0
1.5
1.0
0.5
0.0
050-5568 Rev B
VDS> ID (ON) x RDS (ON)MAX.
250µSEC. PULSE TEST
@ <0.5 % DUTY CYCLE
4.5V
4V
VGS=10V
VGS=20V
TJ = +25°C
TJ = -55°C
TJ = +25°C
TJ = -55°C
5.5V
5V
6V
7V
VGS=15V VGS=8V, 9V & 10V
6.5V
4.5V
4V
5.5V
5V
6V
6.5V
VGS=8V, 9V, 10V & 15V
TJ = +125°C
TJ = +125°C
NORMALIZED TO
VGS = 10V @ 0.5 ID [Cont.]
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
FIGURE 10, MAXIMUM SAFE OPERATING AREA FIGURE 11, TYPICAL CAPACITANCE vs DRAIN-TO-SOURCE VOLTAGE
Qg, TOTAL GATE CHARGE (nC) VSD, SOURCE-TO-DRAIN VOLTAGE (VOLTS)
FIGURE 12, GATE CHARGES vs GATE-TO-SOURCE VOLTAGE FIGURE 13, TYPICAL SOURCE-DRAIN DIODE FORWARD VOLTAGE
VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) ID, DRAIN CURRENT (AMPERES)
IDR, REVERSE DRAIN CURRENT (AMPERES) C, CAPACITANCE (pF)
1 5 10 50 100 200 .01 .1 1 10 50
0 50 100 150 200 250 0 0.4 0.8 1.2 1.6 2.0
APT20M45SVFR
TC =+25°C
TJ =+150°C
SINGLE PULSE
300
100
50
10
5
1
20
16
12
8
4
0
ID = ID [Cont.]
10,000
5,000
1,000
500
100
300
100
50
10
5
1
050-5568 Rev B
OPERATION HERE
LIMITED BY RDS (ON)
TJ =+150°C T
J
=+25°C
Crss
Coss
Ciss
VDS=160V
VDS=40V
10µS
100µS
1mS
10mS
100mS
DC
VDS=100V
APT's devices are covered by one or more of the following U.S.patents: 4,895,810 5,045,903 5,089,434 5,182,234 5,019,522 5,262,336
5,256,583 4,748,103 5,283,202 5,231,474 5,434,095 5,528,058
15.95 (.628)
16.05 (.632)
1.22 (.048)
1.32 (.052) 5.45 (.215) BSC
{2 Plcs.}
4.98 (.196)
5.08 (.200)
1.47 (.058)
1.57 (.062)
2.67 (.105)
2.84 (.112)
0.46 (.018)
{3 Plcs}
0.56 (.022)
Dimensions in Millimeters (Inches)
Heat Sink (Drain)
and Leads
are Plated
3.81 (.150)
4.06 (.160)
(Base of Lead)
Drain
(Heat Sink)
1.98 (.078)
2.08 (.082)
Gate
Drain
Source
0.020 (.001)
0.178 (.007)
1.27 (.050)
1.40 (.055)
11.51 (.453)
11.61 (.457)
13.41 (.528)
13.51 (.532)
Revised
8/29/97
1.04 (.041)
1.15 (.045)
13.79 (.543)
13.99 (.551)
Revised
4/18/95
D3PAK Package Outline
