LM2677 LM2677 SIMPLE SWITCHER High Efficiency 5A Step-Down Voltage Regulator with Sync Literature Number: SNVS077H LM2677 SIMPLE SWITCHER(R) High Efficiency 5A Step-Down Voltage Regulator with Sync General Description Features The LM2677 series of regulators are monolithic integrated circuits which provide all of the active functions for a stepdown (buck) switching regulator capable of driving up to 5A loads with excellent line and load regulation characteristics. High efficiency (>90%) is obtained through the use of a low ON-resistance DMOS power switch. The series consists of fixed output voltages of 3.3V, 5V and 12V and an adjustable output version. The SIMPLE SWITCHER concept provides for a complete design using a minimum number of external components. The switching clock frequency can be provided by an internal fixed frequency oscillator (260KHz) or from an externally provided clock in the range of 280KHz to 400Khz which allows the use of physically smaller sized components. A family of standard inductors for use with the LM2677 are available from several manufacturers to greatly simplify the design process. The external Sync clock provides direct and precise control of the output ripple frequency for consistent filtering or frequency spectrum positioning. The LM2677 series also has built in thermal shutdown, current limiting and an ON/OFF control input that can power down the regulator to a low 50A quiescent current standby condition. The output voltage is guaranteed to a 2% tolerance. Efficiency up to 92% Simple and easy to design with (using off-the-shelf external components) 100 m DMOS output switch 3.3V, 5V and 12V fixed output and adjustable (1.2V to 37V ) versions 50A standby current when switched OFF 2%maximum output tolerance over full line and load conditions Wide input voltage range: 8V to 40V External Sync clock capability (280KHz to 400KHz) 260 KHz fixed frequency internal oscillator -40 to +125C operating junction temperature range Applications Simple to design, high efficiency (>90%) step-down switching regulators Efficient system pre-regulator for linear voltage regulators Battery chargers Communications and radio equipment regulator with synchronized clock frequency Typical Application 10130103 SIMPLE SWITCHER(R) is a registered trademark of National Semiconductor Corporation (c) 2008 National Semiconductor Corporation 101301 www.national.com LM2677 SIMPLE SWITCHER High Efficiency 5A Step-Down Voltage Regulator with Sync February 21, 2008 LM2677 Connection Diagrams and Ordering Information TO-263 Package Top View TO-220 Package Top View 10130101 10130102 Order Number LM2677S-3.3, LM2677S-5.0, LM2677S-12 or LM2677S-ADJ See NSC Package Number TS7B Order Number LM2677T-3.3, LM2677T-5.0, LM2677T-12 or LM2677T-ADJ See NSC Package Number TA07B Top View 10130141 LLP-14 See NS package Number SRC14A Ordering Information for LLP Package Output Voltage Order Information Package Marking Supplied As 12 LM2677SD-12 S0002XB 250 Units on Tape and Reel 12 LM2677SDX-12 S0002XB 2500 Units on Tape and Reel 3.3 LM2677SD-3.3 S0002YB 250 Units on Tape and Reel 3.3 LM2677SDX-3.3 S0002YB 2500 Units on Tape and Reel 5.0 LM2677SD-5.0 S0002ZB 250 Units on Tape and Reel 5.0 LM2677SDX-5.0 S0002ZB 2500 Units on Tape and Reel ADJ LM2677SD-ADJ S0003AB 250 Units on Tape and Reel ADJ LM2677SDX-ADJ S0003AB 2500 Units on Tape and Reel www.national.com 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Input Supply Voltage ON/OFF Pin Voltage Switch Voltage to Ground (Note 12) Boost Pin Voltage Feedback Pin Voltage Power Dissipation 45V -0.1V to 6V -1V to VIN VSW + 8V -0.3V to 14V Internally Limited 2 kV -65C to 150C 4 sec, 260C 10 sec, 240C 75 sec, 219C Operating Ratings Supply Voltage Junction Temperature Range (TJ) 8V to 40V -40C to 125C Electrical Characteristics Limits appearing in bold type face apply over the entire junction temperature range of operation, -40C to 125C. Specifications appearing in normal type apply for TA = TJ = 25C. Sync pin open circuited. LM2677-3.3 Symbol Parameter Conditions Typical (Note 3) Min (Note 4) Max (Note 4) Units 3.234/3.201 3.366/3.399 V VOUT Output Voltage VIN = 8V to 40V, 100mA IOUT 5A 3.3 Efficiency VIN = 12V, ILOAD = 5A 82 % LM2677-5.0 Symbol Parameter Conditions Typical (Note 3) Min (Note 4) Max (Note 4) Units 4.900/4.850 5.100/5.150 V VOUT Output Voltage VIN = 8V to 40V, 100mA IOUT 5A 5.0 Efficiency VIN = 12V, ILOAD = 5A 84 % LM2677-12 Symbol Parameter Conditions Typical (Note 3) Min (Note 4) Max (Note 4) Units 11.76/11.64 12.24/12.36 V VOUT Output Voltage VIN = 15V to 40V, 100mA IOUT 5A 12 Efficiency VIN = 24V, ILOAD = 5A 92 % LM2677-ADJ Symbol Parameter Conditions VFB Feedback Voltage VIN = 8V to 40V, 100mA IOUT 5A VOUT Programmed for 5V Efficiency VIN = 12V, ILOAD = 5A Typ (Note 3) Min (Note 4) Max (Note 4) Units 1.21 1.186/1.174 1.234/1.246 V 84 3 % www.national.com LM2677 ESD (Note 2) Storage Temperature Range Soldering Temperature Wave Infrared Vapor Phase Absolute Maximum Ratings (Note 1) LM2677 All Output Voltage Versions Electrical Characteristics Limits appearing in bold type face apply over the entire junction temperature range of operation, -40C to 125C. Specifications appearing in normal type apply for TA = TJ = 25C. Unless otherwise specified VIN=12V for the 3.3V, 5V and Adjustable versions and VIN=24V for the 12V version, Sync pin open circuited.. Symbol Parameter Conditions Typ Min Max Units 4.2 6 mA 100/150 A 8.3/8.75 A 200 15 A DEVICE PARAMETERS IQ Quiescent Current VFEEDBACK = 8V For 3.3V, 5.0V, and ADJ Versions VFEEDBACK = 15V For 12V Versions ISTBY Standby Quiescent ON/OFF Pin = 0V Current 50 ICL Current Limit 7 IL Output Leakage Current VIN = 40V, ON/OFF Pin = 0V VSWITCH = 0V 1 VSWITCH = -1V 6 6.1/5.75 mA RDS(ON) Switch OnResistance ISWITCH = 5A fO Oscillator Frequency Measured at Switch Pin D Duty Cycle Maximum Duty Cycle Minimum Duty Cycle 91 0 % % IBIAS Feedback Bias Current VFEEDBACK = 1.3V ADJ Version Only 85 nA VON/OFF ON/OFF Threshold Voltage ION/OFF ON/OFF Input Current ON/OFF Input = 0V FSYNC Synchronization Frequency VSYNC(Pin 5)=3.5V, 50% Duty Cycle VSYNC SYNC Threshold Voltage JA Thermal Resistance 0.12 260 1.4 20 225 0.8 0.14/0.225 280 kHz 2.0 V 45 A 400 KHz 1.4 V T Package, Junction to Ambient 65 JA (Note 5) T Package, Junction to Ambient 45 JC (Note 6) T Package, Junction to Case 2 JA S Package, Junction to Ambient 56 JA (Note 7) S Package, Junction to Ambient 35 JA (Note 8) S Package, Junction to Ambient 26 JC (Note 9) S Package, Junction to Case 2 JA SD Package, Junction to Ambient 55 JA (Note 10) SD Package, Junction to Ambient (Note 11) 29 C/W ++ C/W Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings indicate conditions under which of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test condition, see the electrical Characteristics tables. www.national.com 4 Note 3: Typical values are determined with TA = TJ = 25C and represent the most likely norm. Note 4: All limits are guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100% tested during production with TA = TJ = 25C. All limits at temperature extremes are guaranteed via correlation using standard standard Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Note 5: Junction to ambient thermal resistance (no external heat sink) for the 7 lead TO-220 package mounted vertically, with 1/2 inch leads in a socket, or on a PC board with minimum copper area. Note 6: Junction to ambient thermal resistance (no external heat sink) for the 7 lead TO-220 package mounted vertically, with 1/2 inch leads soldered to a PC board containing approximately 4 square inches of (1 oz.) copper area surrounding the leads. Note 7: Junction to ambient thermal resistance for the 7 lead TO-263 mounted horizontally against a PC board area of 0.136 square inches (the same size as the TO-263 package) of 1 oz. (0.0014 in. thick) copper. Note 8: Junction to ambient thermal resistance for the 7 lead TO-263 mounted horizontally against a PC board area of 0.4896 square inches (3.6 times the area of the TO-263 package) of 1 oz. (0.0014 in. thick) copper. Note 9: Junction to ambient thermal resistance for the 7 lead TO-263 mounted horizontally against a PC board copper area of 1.0064 square inches (7.4 times the area of the TO-263 package) of 1 oz. (0.0014 in. thick) copper. Additional copper area will reduce thermal resistance further. See the thermal model in Switchers Made Simple(R) software. Note 10: Junction to ambient thermal resistance for the 14-lead LLP mounted on a PC board copper area equal to the die attach paddle. Note 11: Junction to ambient thermal resistance for the 14-lead LLP mounted on a PC board copper area using 12 vias to a second layer of copper equal to die attach paddle. Additional copper area will reduce thermal resistance further. For layout recommendations, refer to Application Note AN-1187. Note 12: The absolute maximum specification of the 'Switch Voltage to Ground' applies to DC voltage. An extended negative voltage limit of -10V applies to a pulse of up to 20 ns, -6V of 60 ns and -3V of up to 100 ns. 5 www.national.com LM2677 Note 2: ESD was applied using the human-body model, a 100pF capacitor discharged through a 1.5 k resistor into each pin. LM2677 Typical Performance Characteristics Normalized Output Voltage Line Regulation 10130110 10130109 Efficiency vs Input Voltage Efficiency vs ILOAD 10130111 10130112 Switch Current Limit Operating Quiescent Current 10130105 10130104 www.national.com 6 LM2677 Standby Quiescent Current ON/OFF Threshold Voltage 10130140 10130113 ON/OFF Pin Current (Sourcing) Switching Frequency 10130114 10130115 Feedback Pin Bias Current 10130116 7 www.national.com LM2677 Continuous Mode Switching Waveforms VIN = 20V, VOUT = 5V, ILOAD = 5A L = 10 H, COUT = 400 F, COUTESR = 13 m Discontinuous Mode Switching Waveforms VIN = 20V, VOUT = 5V, ILOAD = 500 mA L = 10 H, COUT = 400 F, COUTESR = 13 m 10130117 A: VSW Pin Voltage, 10 V/div. B: Inductor Current, 2 A/div C: Output Ripple Voltage, 20 mV/div AC-Coupled 10130118 A: VSW Pin Voltage, 10 V/div. B: Inductor Current, 1 A/div C: Output Ripple Voltage, 20 mV/div AC-Coupled Horizontal Time Base: 1 s/div Horizontal Time Base: 1 s//iv Load Transient Response for Continuous Mode VIN = 20V, VOUT = 5V L = 10 H, COUT = 400 F, COUTESR = 13 m Load Transient Response for Discontinuous Mode VIN = 20V, VOUT = 5V, L = 10 H, COUT = 400 F, COUTESR = 13 m 10130119 A: Output Voltage, 100 mV//div, AC-Coupled. B: Load Current: 500 mA to 5A Load Pulse Horizontal Time Base: 100 s/div www.national.com 10130120 A: Output Voltage, 100 mV/div, AC-Coupled. B: Load Current: 200 mA to 5A Load Pulse Horizontal Time Base: 200 s/div 8 LM2677 Block Diagram 10130106 * Active Inductor Patent Number 5,514,947 Active Capacitor Patent Number 5,382,918 9 www.national.com LM2677 SYNC This input allows control of the switching clock frequency. If left open-circuited the regulator will be switched at the internal oscillator frequency, between 225KHz and 280KHz. An external clock can be used to force the switching frequency and thereby control the output ripple frequency of the regulator. This capability provides for consistent filtering of the output ripple from system to system as well as precise frequency spectrum positioning of the ripple frequency which is often desired in communications and radio applications. This external frequency must be greater than the LM2677 internal oscillator frequency, which could be as high as 280KHz, to prevent an erroneous reset of the internal ramp oscillator and PWM control of the power switch. The ramp oscillator is reset on the positive going edge of the sync input signal. It is recommended that the external TTL or CMOS compatible clock (between 0V and a level greater than 3V) be ac coupled to the sync input through a 100pf capacitor and a 1K resistor to ground at pin 5 as shown inFigure 1. Application Hints The LM2677 provides all of the active functions required for a step-down (buck) switching regulator. The internal power switch is a DMOS power MOSFET to provide power supply designs with high current capability, up to 5A, and highly efficient operation. The LM2677 is part of the SIMPLE SWITCHER family of power converters. A complete design uses a minimum number of external components, which have been pre-determined from a variety of manufacturers. Using either this data sheet or a design software program called Switchers Made Simple a complete switching power supply can be designed quickly. The software is provided free of charge and can be downloaded from National Semiconductor's Internet site located at http://www.national.com. SWITCH OUTPUT This is the output of a power MOSFET switch connected directly to the input voltage. The switch provides energy to an inductor, an output capacitor and the load circuitry under control of an internal pulse-width-modulator (PWM). The PWM controller is internally clocked by a fixed 260KHz oscillator. In a standard step-down application the duty cycle (Time ON/ Time OFF) of the power switch is proportional to the ratio of the power supply output voltage to the input voltage. The voltage on pin 1 switches between Vin (switch ON) and below ground by the voltage drop of the external Schottky diode (switch OFF). FEEDBACK This is the input to a two-stage high gain amplifier, which drives the PWM controller. It is necessary to connect pin 6 to the actual output of the power supply to set the dc output voltage. For the fixed output devices (3.3V, 5V and 12V outputs), a direct wire connection to the output is all that is required as internal gain setting resistors are provided inside the LM2677. For the adjustable output version two external resistors are required to set the dc output voltage. For stable operation of the power supply it is important to prevent coupling of any inductor flux to the feedback input. INPUT The input voltage for the power supply is connected to pin 2. In addition to providing energy to the load the input voltage also provides bias for the internal circuitry of the LM2677. For guaranteed performance the input voltage must be in the range of 8V to 40V. For best performance of the power supply the input pin should always be bypassed with an input capacitor located close to pin 2. ON/OFF This input provides an electrical ON/OFF control of the power supply. Connecting this pin to ground or to any voltage less than 0.8V will completely turn OFF the regulator. The current drain from the input supply when OFF is only 50A. Pin 7 has an internal pull-up current source of approximately 20A and a protection clamp zener diode of 7V to ground. When electrically driving the ON/OFF pin the high voltage level for the ON condition should not exceed the 6V absolute maximum limit. When ON/OFF control is not required pin 7 should be left open circuited. C BOOST A capacitor must be connected from pin 3 to the switch output, pin 1. This capacitor boosts the gate drive to the internal MOSFET above Vin to fully turn it ON. This minimizes conduction losses in the power switch to maintain high efficiency. The recommended value for C Boost is 0.01F. DAP (LLP PACKAGE) The Die Attach Pad (DAP) can and should be connected to PCB Ground plane/island. For CAD and assembly guidelines refer to Application Note AN-1187 at http:// power.national.com. GROUND This is the ground reference connection for all components in the power supply. In fast-switching, high-current applications such as those implemented with the LM2677, it is recommended that a broad ground plane be used to minimize signal coupling throughout the circuit www.national.com 10 LM2677 DESIGN CONSIDERATIONS 10130107 FIGURE 1. Basic circuit for fixed output voltage applications. 10130108 FIGURE 2. Basic circuit for adjustable output voltage applications Power supply design using the LM2677 is greatly simplified by using recommended external components. A wide range of inductors, capacitors and Schottky diodes from several manufacturers have been evaluated for use in designs that cover the full range of capabilities (input voltage, output voltage and load current) of the LM2677. A simple design procedure using nomographs and component tables provided in this data sheet leads to a working design with very little effort. Alternatively, the design software, LM267X Made Simple (version 6.0), can also be used to provide instant component selection, circuit performance calculations for evaluation, a bill of materials component list and a circuit schematic. INDUCTOR The inductor is the key component in a switching regulator. For efficiency the inductor stores energy during the switch ON time and then transfers energy to the load while the switch is OFF. Nomographs are used to select the inductance value required for a given set of operating conditions. The nomographs as- The individual components from the various manufacturers called out for use are still just a small sample of the vast array of components available in the industry. While these components are recommended, they are not exclusively the only components for use in a design. After a close comparison of component specifications, equivalent devices from other manufacturers could be substituted for use in an application. Important considerations for each external component and an explanation of how the nomographs and selection tables were developed follows. sume that the circuit is operating in continuous mode (the current flowing through the inductor never falls to zero). The magnitude of inductance is selected to maintain a maximum ripple current of 30% of the maximum load current. If the ripple current exceeds this 30% limit the next larger value is selected. 11 www.national.com LM2677 The inductors offered have been specifically manufactured to provide proper operation under all operating conditions of input and output voltage and load current. Several part types are offered for a given amount of inductance. Both surface mount and through-hole devices are available. The inductors from each of the three manufacturers have unique characteristics. Renco: ferrite stick core inductors; benefits are typically lowest cost and can withstand ripple and transient peak currents above the rated value. These inductors have an external magnetic field, which may generate EMI. Pulse Engineering: powdered iron toroid core inductors; these also can withstand higher than rated currents and, being toroid inductors, will have low EMI. Coilcraft: ferrite drum core inductors; these are the smallest physical size inductors and are available only as surface mount components. These inductors also generate EMI but less than stick inductors. OUTPUT CAPACITOR The output capacitor acts to smooth the dc output voltage and also provides energy storage. Selection of an output capacitor, with an associated equivalent series resistance (ESR), impacts both the amount of output ripple voltage and stability of the control loop. The output ripple voltage of the power supply is the product of the capacitor ESR and the inductor ripple current. The capacitor types recommended in the tables were selected for having low ESR ratings. In addition, both surface mount tantalum capacitors and through-hole aluminum electrolytic capacitors are offered as solutions. Impacting frequency stability of the overall control loop, the output capacitance, in conjunction with the inductor, creates a double pole inside the feedback loop. In addition the capacitance and the ESR value create a zero. These frequency response effects together with the internal frequency compensation circuitry of the LM2677 modify the gain and phase shift of the closed loop system. As a general rule for stable switching regulator circuits it is desired to have the unity gain bandwidth of the circuit to be limited to no more than one-sixth of the controller switching frequency. With the fixed 260KHz switching frequency of the LM2677, the output capacitor is selected to provide a unity gain bandwidth of 40KHz maximum. Each recommended capacitor value has been chosen to achieve this result. In some cases multiple capacitors are required either to reduce the ESR of the output capacitor, to minimize output ripple (a ripple voltage of 1% of Vout or less is the assumed performance condition), or to increase the output capacitance to reduce the closed loop unity gain bandwidth (to less than 40KHz). When parallel combinations of capacitors are required it has been assumed that each capacitor is the exact same part type. The RMS current and working voltage (WV) ratings of the output capacitor are also important considerations. In a typical step-down switching regulator, the inductor ripple current (set to be no more than 30% of the maximum load current by the inductor selection) is the current that flows through the output capacitor. The capacitor RMS current rating must be greater than this ripple current. The voltage rating of the output capacitor should be greater than 1.3 times the maximum output voltage of the power supply. If operation of the system at elevated temperatures is required, the capacitor voltage rating may be de-rated to less than the nominal room temperature rating. Careful inspection of the manufacturer's www.national.com specification for de-rating of working voltage with temperature is important. INPUT CAPACITOR Fast changing currents in high current switching regulators place a significant dynamic load on the unregulated power source. An input capacitor helps to provide additional current to the power supply as well as smooth out input voltage variations. Like the output capacitor, the key specifications for the input capacitor are RMS current rating and working voltage. The RMS current flowing through the input capacitor is equal to one-half of the maximum dc load current so the capacitor should be rated to handle this. Paralleling multiple capacitors proportionally increases the current rating of the total capacitance. The voltage rating should also be selected to be 1.3 times the maximum input voltage. Depending on the unregulated input power source, under light load conditions the maximum input voltage could be significantly higher than normal operation and should be considered when selecting an input capacitor. The input capacitor should be placed very close to the input pin of the LM2677. Due to relative high current operation with fast transient changes, the series inductance of input connecting wires or PCB traces can create ringing signals at the input terminal which could possibly propagate to the output or other parts of the circuitry. It may be necessary in some designs to add a small valued (0.1F to 0.47F) ceramic type capacitor in parallel with the input capacitor to prevent or minimize any ringing. CATCH DIODE When the power switch in the LM2677 turns OFF, the current through the inductor continues to flow. The path for this current is through the diode connected between the switch output and ground. This forward biased diode clamps the switch output to a voltage less than ground. This negative voltage must be greater than -1V so a low voltage drop (particularly at high current levels) Schottky diode is recommended. Total efficiency of the entire power supply is significantly impacted by the power lost in the output catch diode. The average current through the catch diode is dependent on the switch duty cycle (D) and is equal to the load current times (1-D). Use of a diode rated for much higher current than is required by the actual application helps to minimize the voltage drop and power loss in the diode. During the switch ON time the diode will be reversed biased by the input voltage. The reverse voltage rating of the diode should be at least 1.3 times greater than the maximum input voltage. BOOST CAPACITOR The boost capacitor creates a voltage used to overdrive the gate of the internal power MOSFET. This improves efficiency by minimizing the on resistance of the switch and associated power loss. For all applications it is recommended to use a 0.01F/50V ceramic capacitor. SYNC COMPONENTS When synchronizing the LM2677 with an external clock it is recommended to connect the clock to pin 5 through a series 100pf capacitor and connect a 1K resistor to ground from pin 5. This RC network creates a short 100nS pulse on each positive edge of the clock to reset the internal ramp oscillator. The reset time of the oscillator is approximately 300nS. ADDITIONAL APPLICATION INFORMATION When the output voltage is greater than approximately 6V, and the duty cycle at minimum input voltage is greater than 12 Step 5: Determine an input capacitor from Table 4 for fixed output voltage applications. Use Table 2 to find the specific capacitor type. For adjustable output circuits select a capacitor from Table 2 with a sufficient working voltage (WV) rating greater than Vin max, and an rms current rating greater than one-half the maximum load current (2 or more capacitors in parallel may be required). Step 6: Select a diode from Table 5. The current rating of the diode must be greater than I load max and the Reverse Voltage rating must be greater than Vin max. Step 7: Include a 0.01F/50V capacitor for Cboost in the design. FIXED OUTPUT VOLTAGE DESIGN EXAMPLE A system logic power supply bus of 3.3V is to be generated from a wall adapter which provides an unregulated DC voltage of 13V to 16V. The maximum load current is 2.5A. Through-hole components are preferred. Step 1: Operating conditions are: Vout = 3.3V Vin max = 16V Iload max = 2.5A Step 2: Select an LM2677T-3.3. The output voltage will have a tolerance of 2% at room temperature and 3% over the full operating temperature range. Step 3: Use the nomograph for the 3.3V device ,Figure 3. The intersection of the 16V horizontal line (Vin max) and the 2.5A vertical line (Iload max) indicates that L33, a 22H inductor, is required. From Table 1, L33 in a through-hole component is available from Renco with part number RL-1283-22-43 or part number PE-53933 from Pulse Engineering. Step 4: Use Table 3 to determine an output capacitor. With a 3.3V output and a 22H inductor there are four through-hole output capacitor solutions with the number of same type capacitors to be paralleled and an identifying capacitor code given. Table 2 provides the actual capacitor characteristics. Any of the following choices will work in the circuit: 1 x 220F/10V Sanyo OS-CON (code C5) 1 x 1000F/35V Sanyo MV-GX (code C10) 1 x 2200F/10V Nichicon PL (code C5) 1 x 1000F/35V Panasonic HFQ (code C7) Step 5: Use Table 4 to select an input capacitor. With 3.3V output and 22H there are three through-hole solutions. These capacitors provide a sufficient voltage rating and an rms current rating greater than 1.25A (1/2 Iload max). Again using Table 2 for specific component characteristics the following choices are suitable: 1 x 1000F/63V Sanyo MV-GX (code C14) 1 x 820F/63V Nichicon PL (code C24) 1 x 560F/50V Panasonic HFQ (code C13) Step 6: From Table 5 a 3A Schottky diode must be selected. For through-hole components 20V rated diodes are sufficient and 2 part types are suitable: 1N5820 SR302 Step 7: A 0.01F capacitor will be used for Cboost. ADJUSTABLE OUTPUT DESIGN EXAMPLE In this example it is desired to convert the voltage from a two battery automotive power supply (voltage range of 20V to 28V, typical in large truck applications) to the 14.8VDC alter- 13 www.national.com LM2677 approximately 50%, the designer should exercise caution in selection of the output filter components. When an application designed to these specific operating conditions is subjected to a current limit fault condition, it may be possible to observe a large hysteresis in the current limit. This can affect the output voltage of the device until the load current is reduced sufficiently to allow the current limit protection circuit to reset itself. Under current limiting conditions, the LM267x is designed to respond in the following manner: 1. At the moment when the inductor current reaches the current limit threshold, the ON-pulse is immediately terminated. This happens for any application condition. 2. However, the current limit block is also designed to momentarily reduce the duty cycle to below 50% to avoid subharmonic oscillations, which could cause the inductor to saturate. 3. Thereafter, once the inductor current falls below the current limit threshold, there is a small relaxation time during which the duty cycle progressively rises back above 50% to the value required to achieve regulation. If the output capacitance is sufficiently `large', it may be possible that as the output tries to recover, the output capacitor charging current is large enough to repeatedly re-trigger the current limit circuit before the output has fully settled. This condition is exacerbated with higher output voltage settings because the energy requirement of the output capacitor varies as the square of the output voltage (1/2CV2), thus requiring an increased charging current. A simple test to determine if this condition might exist for a suspect application is to apply a short circuit across the output of the converter, and then remove the shorted output condition. In an application with properly selected external components, the output will recover smoothly. Practical values of external components that have been experimentally found to work well under these specific operating conditions are COUT = 47F, L = 22H. It should be noted that even with these components, for a device's current limit of ICLIM, the maximum load current under which the possibility of the large current limit hysteresis can be minimized is ICLIM/2. For example, if the input is 24V and the set output voltage is 18V, then for a desired maximum current of 1.5A, the current limit of the chosen switcher must be confirmed to be at least 3A. SIMPLE DESIGN PROCEDURE Using the nomographs and tables in this data sheet (or use the available design software at http://www.national.com) a complete step-down regulator can be designed in a few simple steps. Step 1: Define the power supply operating conditions: Required output voltage Maximum DC input voltage Maximum output load current Step 2: Set the output voltage by selecting a fixed output LM2677 (3.3V, 5V or 12V applications) or determine the required feedback resistors for use with the adjustable LM2677 -ADJ Step 3: Determine the inductor required by using one of the four nomographs, Figure 3 through Figure 6. Table 1 provides a specific manufacturer and part number for the inductor. Step 4: Using Table 3 (fixed output voltage) or Table 6 (adjustable output voltage), determine the output capacitance required for stable operation. Table 2 provides the specific capacitor type from the manufacturer of choice. LM2677 nator supply typically used to power electronic equipment from single battery 12V vehicle systems. The load current required is 2A maximum. It is also desired to implement the power supply with all surface mount components. Step 1: Operating conditions are: Vout = 14.8V Vin max = 28V Iload max = 2A Step 2: Select an LM2677S-ADJ. To set the output voltage to 14.9V two resistors need to be chosen (R1 and R2 in Figure 2). For the adjustable device the output voltage is set by the following relationship: Using Figure 6, the intersection of 27V*S horizontally and the 2A vertical line (Iload max) indicates that L38 , a 68H inductor, should be used. From Table 1, L38 in a surface mount component is available from Pulse Engineering with part number PE-54038S. Step 4: Use Table 6 to determine an output capacitor. With a 14.8V output the 12.5 to 15V row is used and with a 68H inductor there are three surface mount output capacitor solutions. Table 2 provides the actual capacitor characteristics based on the C Code number. Any of the following choices can be used: 1 x 33F/20V AVX TPS (code C6) 1 x 47F/20V Sprague 594 (code C8) 1 x 47F/20V Kemet T495 (code C8) Important Note: When using the adjustable device in low voltage applications (less than 3V output), if the nomograph, Figure 6, selects an inductance of 22H or less, Table 6 does not provide an output capacitor solution. With these conditions the number of output capacitors required for stable operation becomes impractical. It is recommended to use either a 33H or 47H inductor and the output capacitors from Table 6. Step 5: An input capacitor for this example will require at least a 35V WV rating with an rms current rating of 1A (1/2 Iout max). From Table 2 it can be seen that C12, a 33F/35V capacitor from Sprague, has the required voltage/current rating of the surface mount components. Step 6: From Table 5 a 3A Schottky diode must be selected. For surface mount diodes with a margin of safety on the voltage rating one of five diodes can be used: SK34 30BQ040 30WQ04F MBRS340 MBRD340 Step 7: A 0.01F capacitor will be used for Cboost. Where VFB is the feedback voltage of typically 1.21V. A recommended value to use for R1 is 1K. In this example then R2 is determined to be: R2 = 11.23K The closest standard 1% tolerance value to use is 11.3K This will set the nominal output voltage to 14.88V which is within 0.5% of the target value. Step 3: To use the nomograph for the adjustable device, Figure 6, requires a calculation of the inductor Volt*microsecond constant (E*T expressed in V*S) from the following formula: where VSAT is the voltage drop across the internal power switch which is Rds(ON) times Iload. In this example this would be typically 0.15 x 2A or 0.3V and VD is the voltage drop across the forward bisased Schottky diode, typically 0.5V. The switching frequency of 260KHz is the nominal value to use to estimate the ON time of the switch during which energy is stored in the inductor. For this example E*T is found to be: www.national.com LLP PACKAGE DEVICES The LM2677 is offered in the 14 lead LLP surface mount package to allow for a significantly decreased footprint with equivalent power dissipation compared to the TO-263. For details on mounting and soldering specifications, refer to Application Note AN-1187. 14 LM2677 Inductor Selection Guides For Continuous Mode Operation 10130123 10130121 FIGURE 5. LM2677-12 FIGURE 3. LM2677-3.3 10130122 10130124 FIGURE 4. LM2677-5.0 FIGURE 6. LM2677-ADJ 15 www.national.com LM2677 TABLE 1. Inductor Manufacturer Part Numbers Inductor Inductance Reference (H) Number Renco Current (A) Pulse Engineering Through Hole Surface Mount Through Hole Surface Mount Coilcraft Surface Mount L23 33 1.35 RL-5471-7 RL1500-33 PE-53823 PE-53823S DO3316-333 L24 22 1.65 RL-1283-22-43 RL1500-22 PE-53824 PE-53824S DO3316-223 L25 15 2.00 RL-1283-15-43 RL1500-15 PE-53825 PE-53825S DO3316-153 L29 100 1.41 RL-5471-4 RL-6050-100 PE-53829 PE-53829S DO5022P-104 L30 68 1.71 RL-5471-5 RL6050-68 PE-53830 PE-53830S DO5022P-683 L31 47 2.06 RL-5471-6 RL6050-47 PE-53831 PE-53831S DO5022P-473 L32 33 2.46 RL-5471-7 RL6050-33 PE-53932 PE-53932S DO5022P-333 L33 22 3.02 RL-1283-22-43 RL6050-22 PE-53933 PE-53933S DO5022P-223 L34 15 3.65 RL-1283-15-43 -- PE-53934 PE-53934S DO5022P-153 L38 68 2.97 RL-5472-2 -- PE-54038 PE-54038S -- L39 47 3.57 RL-5472-3 -- PE-54039 PE-54039S -- L40 33 4.26 RL-1283-33-43 -- PE-54040 PE-54040S -- L41 22 5.22 RL-1283-22-43 -- PE-54041 P0841 -- L44 68 3.45 RL-5473-3 -- PE-54044 L45 10 4.47 RL-1283-10-43 -- L46 15 5.60 RL-1283-15-43 -- L47 10 5.66 RL-1283-10-43 L48 47 5.61 L49 33 5.61 -- -- DO5022P-103HC -- P0846 DO5022P-153HC -- -- P0847 DO5022P-103HC RL-1282-47-43 -- -- P0848 -- RL-1282-33-43 -- -- P0849 -- Inductor Manufacturer Contact Numbers Phone (800) 322-2645 FAX (708) 639-1469 Phone +44 1236 730 595 FAX +44 1236 730 627 Phone (619) 674-8100 FAX (619) 674-8262 Pulse Engineering, Phone +353 93 24 107 Europe FAX +353 93 24 459 Renco Electronics Phone (800) 645-5828 FAX (516) 586-5562 Coilcraft Coilcraft, Europe Pulse Engineering www.national.com -- P0845 16 LM2677 Capacitor Selection Guides TABLE 2. Input and Output Capacitor Codes Capacitor Reference Code Surface Mount AVX TPS Series C (F) WV (V) Irms (A) Sprague 594D Series C (F) WV (V) Irms (A) Kemet T495 Series C (F) WV (V) Irms (A) C1 330 6.3 1.15 120 6.3 1.1 100 6.3 0.82 C2 100 10 1.1 220 6.3 1.4 220 6.3 1.1 C3 220 10 1.15 68 10 1.05 330 6.3 1.1 C4 47 16 0.89 150 10 1.35 100 10 1.1 C5 100 16 1.15 47 16 1 150 10 1.1 C6 33 20 0.77 100 16 1.3 220 10 1.1 C7 68 20 0.94 180 16 1.95 33 20 0.78 C8 22 25 0.77 47 20 1.15 47 20 0.94 C9 10 35 0.63 33 25 1.05 68 20 0.94 C10 22 35 0.66 68 25 1.6 10 35 0.63 C11 15 35 0.75 22 35 0.63 C12 33 35 1 4.7 50 0.66 C13 15 50 0.9 Input and Output Capacitor Codes (continued) Through Hole Capacitor Sanyo OS-CON SA Series Sanyo MV-GX Series Nichicon PL Series Reference C (F) WV (V) Irms C (F) WV (V) Irms C (F) WV (V) Irms Code (A) (A) (A) Panasonic HFQ Series C (F) WV (V) Irms (A) C1 47 6.3 1 1000 6.3 0.8 680 10 0.8 82 35 0.4 C2 150 6.3 1.95 270 16 0.6 820 10 0.98 120 35 0.44 C3 330 6.3 2.45 470 16 0.75 1000 10 1.06 220 35 0.76 C4 100 10 1.87 560 16 0.95 1200 10 1.28 330 35 1.01 C5 220 10 2.36 820 16 1.25 2200 10 1.71 560 35 1.4 C6 33 16 0.96 1000 16 1.3 3300 10 2.18 820 35 1.62 C7 100 16 1.92 150 35 0.65 3900 10 2.36 1000 35 1.73 C8 150 16 2.28 470 35 1.3 6800 10 2.68 2200 35 2.8 C9 100 20 2.25 680 35 1.4 180 16 0.41 56 50 0.36 C10 47 25 2.09 1000 35 1.7 270 16 0.55 100 50 0.5 C11 220 63 0.76 470 16 0.77 220 50 0.92 C12 470 63 1.2 680 16 1.02 470 50 1.44 C13 680 63 1.5 820 16 1.22 560 50 1.68 C14 1000 63 1.75 1800 16 1.88 1200 50 2.22 C15 220 25 0.63 330 63 1.42 C16 220 35 0.79 1500 63 2.51 C17 560 35 1.43 C18 2200 35 2.68 C19 150 50 0.82 C20 220 50 1.04 C21 330 50 1.3 C22 100 63 0.75 C23 390 63 1.62 C24 820 63 2.22 C25 1200 63 2.51 17 www.national.com LM2677 Capacitor Manufacturer Contact Numbers Nichicon Panasonic AVX Sprague/Vishay Sanyo Kemet www.national.com Phone (847) 843-7500 FAX (847) 843-2798 Phone (714) 373-7857 FAX (714) 373-7102 Phone (845) 448-9411 FAX (845) 448-1943 Phone (207) 324-4140 FAX (207) 324-7223 Phone (619) 661-6322 FAX (619) 661-1055 Phone (864) 963-6300 FAX (864) 963-6521 18 LM2677 TABLE 3. Output Capacitors for Fixed Output Voltage Application Output Inductance Voltage (V) (H) 3.3 5 12 Surface Mount AVX TPS Series Sprague 594D Series Kemet T495 Series No. C Code No. C Code No. C Code 10 5 C1 5 C1 5 C2 15 4 C1 4 C1 4 C3 22 3 C2 2 C7 3 C4 33 1 C1 2 C7 3 C4 10 4 C2 4 C6 4 C4 15 3 C3 2 C7 3 C5 22 3 C2 2 C7 3 C4 33 2 C2 2 C3 2 C4 47 2 C2 1 C7 2 C4 10 4 C5 3 C6 5 C9 15 3 C5 2 C7 4 C9 22 2 C5 2 C6 3 C8 33 2 C5 1 C7 3 C8 47 2 C4 1 C6 2 C8 68 1 C5 1 C5 2 C7 100 1 C4 1 C5 1 C8 Through Hole Output Inductance Voltage (V) (H) 3.3 5 12 Sanyo OS-CON SA Series Sanyo MV-GX Series Nichicon PL Series Panasonic HFQ Series No. C Code No. C Code No. C Code No. C Code 10 2 C5 2 C6 1 C8 2 C6 15 2 C5 2 C5 1 C7 2 C5 22 1 C5 1 C10 1 C5 1 C7 33 1 C5 1 C10 1 C5 1 C7 10 2 C4 2 C5 1 C6 2 C5 15 1 C5 1 C10 1 C5 1 C7 22 1 C5 1 C9 1 C5 1 C5 33 1 C4 1 C5 1 C4 1 C4 47 1 C4 1 C4 1 C2 2 C4 10 2 C7 1 C10 1 C14 2 C4 15 1 C8 1 C6 1 C17 1 C5 22 1 C7 1 C5 1 C13 1 C5 33 1 C7 1 C4 1 C12 1 C4 47 1 C7 1 C3 1 C11 1 C3 68 1 C6 1 C2 1 C10 1 C3 100 1 C6 1 C2 1 C9 1 C1 No. represents the number of identical capacitor types to be connected in parallel C Code indicates the Capacitor Reference number in Table 2for identifying the specific component from the manufacturer. 19 www.national.com LM2677 TABLE 4. Input Capacitors for Fixed Output Voltage Application (Assumes worst case maximum input voltage and load current for a given inductance value) Output Inductance Voltage (V) (H) 3.3 5 12 Surface Mount AVX TPS Series Sprague 594D Series Kemet T495 Series No. C Code No. C Code No. 10 3 C7 2 C10 3 C Code C9 15 * * 3 C13 4 C12 22 * * 2 C13 3 C12 33 * * 2 C13 3 C12 10 3 C4 2 C6 3 C9 15 4 C9 3 C12 4 C10 22 * * 3 C13 4 C12 33 * * 2 C13 3 C12 47 * * 1 C13 2 C12 10 4 C9 2 C10 4 C10 15 4 C8 2 C10 4 C10 22 4 C9 3 C12 4 C10 33 * * 3 C13 4 C12 47 * * 2 C13 3 C12 68 * * 2 C13 2 C12 100 * * 1 C13 2 C12 Through Hole Output Inductance Voltage (V) (H) 3.3 5 12 Sanyo OS-CON SA Series Sanyo MV-GX Series No. C Code No. 10 2 C9 15 * * 22 * 33 * 10 15 Nichicon PL Series C Code No. C Code No. 2 C8 1 C18 1 C8 2 C13 1 C25 1 C16 * 1 C14 1 C24 1 C16 * 1 C14 1 C24 1 C16 2 C7 2 C8 1 C25 1 C8 * * 2 C8 1 C25 1 C8 22 * * 2 C13 1 C25 1 C16 33 * * 1 C14 1 C23 1 C13 47 * * 1 C12 1 C19 1 C11 10 2 C10 2 C8 1 C18 1 C8 15 2 C10 2 C8 1 C18 1 C8 22 * * 2 C8 1 C18 1 C8 33 * * 2 C12 1 C24 1 C14 47 * * 1 C14 1 C23 1 C13 68 * * 1 C13 1 C21 1 C15 100 * * 1 C11 1 C22 1 C11 * Check voltage rating of capacitors to be greater than application input voltage. No. represents the number of identical capacitor types to be connected in parallel C Code indicates the Capacitor Reference number in Table 2 for identifying the specific component from the manufacturer. www.national.com Panasonic HFQ Series 20 C Code LM2677 TABLE 5. Schottky Diode Selection Table Reverse Voltage (V) 3A 20V SK32 30V SK33 30WQ03F MBRD835L 40V SK34 30BQ040 30WQ04F MBRS340 MBRD340 MBRB1545CT 6TQ045S 50V or More Surface Mount Through Hole 5A or More 3A 5A or More 1N5820 SR302 SK35 30WQ05F 1N5821 31DQ03 1N5822 MBR340 31DQ04 SR403 MBR745 80SQ045 6TQ045 MBR350 31DQ05 SR305 Diode Manufacturer Contact Numbers International Rectifier Motorola General Semiconductor Diodes, Inc. Phone (310) 322-3331 FAX (310) 322-3332 Phone (800) 521-6274 FAX (602) 244-6609 Phone (516) 847-3000 FAX (516) 847-3236 Phone (805) 446-4800 FAX (805) 446-4850 21 www.national.com LM2677 TABLE 6. Output Capacitors for Adjustable Output Voltage Applications Output Voltage (V) 1.21 to 2.50 2.5 to 3.75 3.75 to 5 5 to 6.25 6.25 to 7.5 7.5 to 10 10 to 12.5 12.5 to 15 15 to 20 20 to 30 30 to 37 www.national.com Inductance (H) Surface Mount AVX TPS Series Sprague 594D Series Kemet T495 Series No. C Code No. C Code No. C Code 33* 7 C1 6 C2 7 C3 47* 5 C1 4 C2 5 C3 33* 4 C1 3 C2 4 C3 47* 3 C1 2 C2 3 C3 22 4 C1 3 C2 4 C3 33 3 C1 2 C2 3 C3 47 2 C1 2 C2 2 C3 22 3 C2 1 C3 3 C4 33 2 C2 2 C3 2 C4 47 2 C2 2 C3 2 C4 68 1 C2 1 C3 1 C4 22 3 C2 1 C4 3 C4 33 2 C2 1 C3 2 C4 47 1 C3 1 C4 1 C6 68 1 C2 1 C3 1 C4 33 2 C5 1 C6 2 C8 47 1 C5 1 C6 2 C8 68 1 C5 1 C6 1 C8 100 1 C4 1 C5 1 C8 33 1 C5 1 C6 2 C8 47 1 C5 1 C6 2 C8 68 1 C5 1 C6 1 C8 100 1 C5 1 C6 1 C8 33 1 C6 1 C8 1 C8 47 1 C6 1 C8 1 C8 C8 68 1 C6 1 C8 1 100 1 C6 1 C8 1 C8 33 1 C8 1 C10 2 C10 47 1 C8 1 C9 2 C10 68 1 C8 1 C9 2 C10 100 1 C8 1 C9 1 C10 33 2 C9 2 C11 2 C11 47 1 C10 1 C12 1 C11 68 1 C9 1 C12 1 C11 100 1 C9 1 C12 1 C11 10 4 C13 8 C12 15 3 C13 5 C12 2 C13 4 C12 33 1 C13 3 C12 47 1 C13 2 C12 68 1 C13 2 C12 22 No Values Available 22 LM2677 Output Capacitors for Adjustable Output Voltage Applications (continued) Through Hole Output Voltage (V) 1.21 to 2.50 2.5 to 3.75 3.75 to 5 5 to 6.25 6.25 to 7.5 7.5 to 10 10 to 12.5 12.5 to 15 15 to 20 Inductance (H) Sanyo OS-CON SA Series 30 to 37 Nichicon PL Series Panasonic HFQ Series No. C Code No. C Code No. C Code No. 33* 2 C3 5 C1 5 C3 3 C 47* 2 C2 4 C1 3 C3 2 C5 33* 1 C3 3 C1 3 C1 2 C5 47* 1 C2 2 C1 2 C3 1 C5 22 1 C3 3 C1 3 C1 2 C5 33 1 C2 2 C1 2 C1 1 C5 47 1 C2 2 C1 1 C3 1 C5 22 1 C5 2 C6 2 C3 2 C5 33 1 C4 1 C6 2 C1 1 C5 47 1 C4 1 C6 1 C3 1 C5 68 1 C4 1 C6 1 C1 1 C5 22 1 C5 1 C6 2 C1 1 C5 33 1 C4 1 C6 1 C3 1 C5 47 1 C4 1 C6 1 C1 1 C5 68 1 C4 1 C2 1 C1 1 C5 33 1 C7 1 C6 1 C14 1 C5 47 1 C7 1 C6 1 C14 1 C5 68 1 C7 1 C2 1 C14 1 C2 100 1 C7 1 C2 1 C14 1 C2 33 1 C7 1 C6 1 C14 1 C5 47 1 C7 1 C2 1 C14 1 C5 68 1 C7 1 C2 1 C9 1 C2 100 1 C7 1 C2 1 C9 1 C2 33 1 C9 1 C10 1 C15 1 C2 47 1 C9 1 C10 1 C15 1 C2 68 1 C9 1 C10 1 C15 1 C2 100 1 C9 1 C10 1 C15 1 C2 33 1 C10 1 C7 1 C15 1 C2 47 1 C10 1 C7 1 C15 1 C2 68 1 C10 1 C7 1 C15 1 C2 100 1 C10 1 C7 1 C15 1 C2 1 C7 1 C16 1 C2 33 20 to 30 Sanyo MV-GX Series C Code 47 No Values 1 C7 1 C16 1 C2 68 Available 1 C7 1 C16 1 C2 100 1 C7 1 C16 1 C2 10 1 C12 1 C20 1 C10 15 1 C11 1 C20 1 C11 22 No Values 1 C11 1 C20 1 C10 33 Available 1 C11 1 C20 1 C10 47 1 C11 1 C20 1 C10 68 1 C11 1 C20 1 C10 * Set to a higher value for a practical design solution. See Applications Hints section No. represents the number of identical capacitor types to be connected in parallel C Code indicates the Capacitor Reference number in Table 2 for identifying the specific component from the manufacturer. 23 www.national.com LM2677 Physical Dimensions inches (millimeters) unless otherwise noted TO-263 Surface Mount Power Package Order Number LM2677S-3.3, LM2677S-5.0, LM2677S-12 or LM2677S-ADJ NS Package Number TS7B www.national.com 24 LM2677 TO-220 Power Package Order Number LM2677T-3.3, LM2677T-5.0, LM2677T-12 or LM2677T-ADJ NS Package Number TA07B 14-Lead LLP Package NS Package Number SRC14A 25 www.national.com LM2677 SIMPLE SWITCHER High Efficiency 5A Step-Down Voltage Regulator with Sync Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated