SF2030A - RF Monolithics - Datasheet.Live

®

Preliminary

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 1

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

Notes:

1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to

50 Ω and measured with 50 Ω network analyzer.

2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.

3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance

matching design. See Application Note No. 42 for details.

4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."

5. The design, manufacturing process, and specifications of this filter are subject to change.

6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that

the filter must always be installed in one direction per the circuit design.

7. US and international patents may apply.

8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.

10. Electrostatic Sensitive Device. Observe precautions for handling.

Electrical Characteristics

Characteristic Sym Notes Min Typ Max Units

Nominal Frequency fN243.95 MHz

Nominal Insertion Attenuation 5dB

Pass band width at 3 dB (Relative to Fn) B3dB kHz

Point of left side -150

Point of right side +150

Amplitude Ripple (peak-valley)

FN - 110 kHz ---- Fn + 110kHz 0.6 1.0 dB

Group Delay Ripple FN - 110 kHz ---- Fn + 110kHz 0.5 µsec

Relative Attenuation (Relative to Fn)

Fn - 21.6 MHz 60 dB

Fn - 21.4 MHz 60 dB

Fn - 10.8 MHz 55 dB

Fn - 1.2 MHz 30 dB

Fn - 0.7 MHz 30 dB

Fn - 0.6 MHz 30 dB

Fn - 0.5 MHz 15 dB

Fn + 0.5 MHz 15 dB

Fn + 0.6 MHz 30 dB

Fn + 0.7 MHz 30 dB

Fn + 1.2 MHz 30 dB

Fn + 10.8 MHz 55 dB

Lid Symbolization (YY=year, WW=week, S=shift) See note 4 RFM SF2030A YYWWS

SM1154-14

•Designed for PHS BTS IF Applications

•Excellent Size-to Performance Ratio

•Hermetic 11.5 X 4.0 mm Surface-Mount Case

•Complies with Directive 2002/95/EC (RoHS)

Maximum Ratings Rating Value Units

Operating Temperature Range -15 to +80 °C

Storage Temperature Range -40 to +85 °C

Maximum DC Voltage 30 V

Maximum Source Power +15 dBm

Maximum Soldering Profile 260°C for 30sec

243.95 MHz

SAW Filter

SF2030A

Pb

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 2

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

CH1 S11 1 U FS

CENTR 243 .950 MHz SPAN 10 .000 MHz

Cor

CH2 S21 LOG 10 dB/ REF -10 dB

CENTER 243 .950 000 MHz SPAN 10 .000 000 MHz

Cor

CH3 S22 1 U FS

CENTR 243 .950 MHz SPAN 10 .000 MHz

Cor

23 Oct 2007 10:46:35

1

1:62 .482 9.6777 6.3138 nH

243 .950 000 MHz

1

2

3 4

1:0.0000 dB 0.000 000 MHz

Max REF=1

CH2 Markers

BW: . 483040 MHz

cent :243 .955294 MHz

Q:505 .04

1_ loss :-3 .7998 dB

1

1:47 .762 1.4551 949 .30 pH

243 .950 000 MHz

SF2030A

Full

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 3

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

CH1 S21 LOG 5 dB/ REF -10 dB

Cor

PRm

CH2 S21 DEL 50 ns/ REF 1.8 us

START 242 .950 000 MHz STOP 244 .950 000 MHz

Cor

Smo

PRm

15 Dec 2004 10:01:44

1

1:-7 .7068 dB 243 .950 000 MHz

1

2

3

1:0.0000 s0.000 000 MHz

REF=1

CH2 Markers

2:10 .872 ns

-144 .000 kHz

3:45 .700 ns

144 .000 kHz

3

P1

P2

SF2030A

C1

3.1pF

C2

2.7pF

R2 240

R1 240

L1

43nH

L2 51nH

0

SF2030A Demo schematic

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 4

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

CH1 S21 LOG 10 dB/ REF 0 dB

CENTER 243 .950 000 MHz SPAN 20 .000 000 MHz

Cor

PRm

15 Dec 2004 10:04:38

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 5

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

14-Terminal Ceramic Surface-Mount Case

11.5 x 4.0 mm Nominal Footprint

Recommended PCB Footprint

Case Dimensions

Dimension mm Inches

Min Nom Max Min Nom Max

A11.4 11.5 11.6 .442 0.450 0.458

B3.8 4.0 4.2 .150 0.157 .166

C1.4 1.6 1.8 .057 0.063 .069

D1.3 1.5 1.7 .053 0.059 .065

E0.76 0.030

F1.27 0.050

G1.27 0.050

H0.1 0.004

Materials

Solder Pad

Termination Au plating 30 - 60 µinches (76.2-152 µm) over 80-

200 µinches (203-508 µm) Ni.

Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11%

Phosphorus) 100-200 µinches Thick

Body Al2O3 Ceramic

Pb Free

Electrical Connections

Connection Terminals

Input 2

Output 9

Ground All Others

1

2

3

4

5

6

7

14

13

12

11

10

9

8

B

A

C

D

14

13

12

11

10

9

8

H

E

F

G

1

2

3

4

5

6

7

0.034 TYP.

(0.86)

0.050

(1.27) TYP.

0.067 TYP.

(1.70)

0.190

(4.84)

0.334 REF.

(8.48)

SM1154-14 Case

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 6

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

COMPONENTORIENTATIONandDIMENSIONS

Carrier Tape Dimensions

Ao 4.55 mm ±0.1

Bo 12.04 mm ±0.1

Ko 2.13 mm ±0.1

Pitch 8.00 mm ±0.1

W24.00 mm ±0.3

W

(CARRIER TAPE SIZE)

AO

BO

P

(PITCH)

COVER TAPE SIZE

KO

COVER TAPE

1.5 mm +0.1

-0.0

4.0 mm ±0.1

2.0 mm ±0.1

1.75 mm ±0.1

1.5 mm +0.3

-0.0

PIN #1

USER DIRECTION OF FEED

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 7

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

Leader and Trailer specifications (Based upon EIA-481)

7 Inch Reel Quantity 500

Symbol AN C D BW1W2

Dimension 178 +0

-4 60 ±1 13 +0.5

-0.2 20.2 +1.5

-0 2±0.5 24.4 +2

-0 30.4 MAX

13 Inch Reel Quantity 2000

Symbol AN C D BW1W2

Dimension 330 +0

-4 100 ±2 13 +0.5

-0.2 20.2 +1.5

-0 2±0.5 24.4 +2

-0 30.4 MAX

Dimensions of the leader and trailer

Dimensional drawing of the reel

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 8

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

Additional items

(1) Cover tape peeling strength

The cover tape shall be adhered evenly to the carrier tape along both sides in the pulling direction.

The cover tape peeling strength shall be as follows for an angle between the cover tape and the pulling

direction of 165° to 180° (see the figure) and a peeling speed of 300mm/min. ±10mm/min.

[EIA-481] 0.1N to 1.3N for a tape width of 12 to 56mm

Tape material

(1) Carrier tape [anti-charging treatment: carbon used] Surface resistivity: 1 x 108 or less

Material: Polystyrene or Polycarbonate

(2) Cover tape material: Polyester (anti-charging treated) Surface resistivity: 1 x 1012 or less

t = 50 to 100µm

Warranty periods

Cover tape peeling strength and mounting performance of stored components.

2-1. Cover tape peeling strength: One year after delivery (Peeling strength: 0.1N to 1.3N)

Number of missing components

There shall not be two or more consecutive missing components. Also, the maximum number of missing

components shall be the larger of one piece or 0.1%.

Storage environment

Keep the product on which taping has been performed to a temperature below 40°C and a humidity within

80% RH. Do not subject in the direct sun.

Fixing method

1. Insert the tip of the carrier tape into the groove.

2. Fix the tip of the cover tape with adhesive tape.

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 9

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 10

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

7 Inch

Reel

Quanity

Per Reel Number Reels

Per Carton External Caton

Dimensions Reel

Weight Shipping Carton

Weight Total

Weight

500 4 254 x 254 x 127 mm

10 x 10 x 5 inches 896 g 448 g 1344 g

500 10 254 x 254 x 203 mm

10 x 10 x 8 inches 2240 g 448 g 2688 g

13 Inch

Reel

Quanity

Per Reel Number Reels

Per Carton External Caton

Dimensions Reel

Weight Shipping Carton

Weight Total

Weight

2000 2 356 x 356 x 102 mm

14 x 14 x 4 inches 1288 g 448 g 1736 g

2000 4 356 x 356 x 178 mm

14 x 14 x 7 inches 2576 g 448 g 3024 g

2000 8 356 x 356 x 356 mm

14 x 14 x 14 inches 5152 g 448 g 5600 g

Package for Shipment

243.95 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 11

RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

RFM Qualification and Reliability Test

Test Standard Test Parameters Pass / FailCriteria

1Life at

Elevated

Temperature

MIL-STD-202

Method 108

Condition C

1,000 Hours

125°C

Unbiased

Within

Electrical &

Hermetic Spec.

(Note 1)

2Temperature

Cycling

JESD22

Method JA-104

Air-to-Air

-55 ×Cto +125 ×C

20 min. Dwell

1,000 cycles

3Vibration,

Variable

Frequency

MIL-STD-883

Method 2007

Condition B

50g Max.

4 Cycles, 3 Axis

20 Hz to 2 kHz to

20 Hz

4Mechanical

Shock

MIL-STD-883

Method 2002

Condition B

1,500g Max.

5 Shocks

±3 Axis

5Destructive

Bond

Strength

MIL-STD-883

Method 2011

Condition C

Wire Bond Pull

Strength 2.0 grams

(After Seal)

6Die Shear

Strength MIL-STD-883

Method 2019 Shear Strength

0.6 kg

(Strength/area

limit in

development)

7Solderability

(Note 2) J-STD-002

Method B

8 hr. steam age

245 × C solder

temperature

5 second dwell

>95% wetted

surface

8Physical

Dimensions JESD22

Method JB-100 Critical

Dimensions Within

specifications

9Temperature

Characteristics RFM Procedure Frequency over

Temperature Within

specifications

10 Terminal

Strength

(Note 2)

MIL-STD-833

Method 2004

Condition A & D

Cond. A-Lead

Tension

Cond. B -Pad

Adhesionr 24

8 oz. - 30 sec.

Visual Requirements

& meets

Hermetic Spec.

11 Resistance to

Solvents MIL-STD-883

Method 2015 Solvents a, b, d Visual

Requirements

12 Steady State

Life MIL-STD-883

Method 1005

1,000 Hours

Max. Operating

Temperature

Rated Voltage

Within

Electrical &

Hermetic Spec.

(Note 1)

13 Internal Water-

Vapor Content MIL-STD-883

Method 1018 < 5,001 PPM

14 Constant

Acceleration

MIL-STD-883

Method 2001

Y1 Direction 30,000g

Within

Electrical &

Hermetic Spec.

(Note 1)

15 Substrate

Attach Strength MIL-STD-883

Method 2027 Tensile Strength of

Die Attachment Custom per Device