o8mm AP8M Series o10mm AP1M Series LED Illuminated Miniature Pilot Lights Super LED achieves high brightness * New blue and pure white LED lamps * 12V and 24V types can be used on both AC/DC voltages Lens color: S (blue) Lens color: PW (pure white) AP8M series AP1M series o8/o10 AP Series LED Illuminated Miniature Pilot Lights Specifications Input Type Internal Circuits Full voltage Operating Voltage 5V DC Operating Voltage 12V AC/DC 9 mA (yellow: 15 mA) Illumination Color (code) A (amber), G (green), R (red), PW (pure white), S (blue), W (white), Y (yellow) Operating Temperature -20 to +55C (no freezing) Operating Humidity 45 to 85% RH (no condensation) Insulation Resistance Between live and dead parts: 100 M minimum (500V DC megger) Dielectric Strength Between live and dead parts: 1000V, 1 minute Solder Terminal 100V -- (-) (+) 5V DC Rated Current Reverse Withstand Voltage Circuit Diagram 24V AC/DC LED Chip 12V AC/DC 24V AC/DC Protection Diode Zener Diode Resistor -- Standards Soldering 350C maximum (3 seconds) Safety Standards 2 File No. or Organization Applicable Wire o1.0mm or 0.75 mm maximum Weight AP8M: 2.0g, AP1M: 2.5g UL508 UL Recognized, File No. E68961 Degree of Protection AP8M: dustproof (IP40) AP1M: watertight (IP65), oiltight (according to IEC 60529) CSA C22.2, No. 14 CSA Certified File No. LR107101, LR92374 EN60947-5-1 European Commission's Low Voltage Directive RoHS directive compliant (2002/95/IEC) The AP series LED illuminated miniature pilot lights do not contain lead, cadmium, mercury, hexavalent chromium, PBB, or PBDE. Types u AP8M Series (o8mm) Shape Dome Operating Voltage 5V DC 5% 12V AC/DC 10% 24V AC/DC 10% Flat 5V DC 5% 12V AC/DC 10% 24V AC/DC 10% Type No. AP8M255 AP8M255PN10 AP8M211 AP8M211PN10 AP8M222 AP8M222PN10 AP8M155 AP8M155PN10 AP8M111 AP8M111PN10 AP8M122 AP8M122PN10 Package Quantity 1 10 1 10 1 10 1 10 1 10 1 10 Lens Color (code) Specify a lens color code in place of in the Type No. A (amber) G (green) PW (pure white) R (red) S (blue) W (white) Y (yellow) * The lens or LED cannot be removed or replaced. * Degree of protection: IP40 u AP1M Series (o10mm) Shape Dome Operating Voltage 5V DC 5% 12V AC/DC 10% 24V AC/DC 10% Flat 5V DC 5% 12V AC/DC 10% 24V AC/DC 10% Type No. AP1M255 AP1M255PN10 AP1M211 AP1M211PN10 AP1M222 AP1M222PN10 AP1M155 AP1M155PN10 AP1M111 AP1M111PN10 AP1M122 AP1M122PN10 * The LED cannot be removed. The lens can be removed and replaced. * Degree of protection: IP65 2 Package Quantity 1 10 1 10 1 10 1 10 1 10 1 10 Lens Color (code) Specify a lens color code in place of in the Type No. A (amber) G (green) PW (pure white) R (red) S (blue) W (white) Y (yellow) AP Series LED Illuminated Miniature Pilot Lights o8/o10 Accessories Shape Type Material Ordering Type No. Package Quantity Dimensions (mm) o10 * Used to tighten the locking ring when installing the AP unit onto a panel. * Tightening torque: 0.29 N*m M M T-0 T- 0 0 0 3: 4: o1 o9 2 .5 Locking Ring Wrench MT-003 Nickel-plated brass o8 1 MT-004 60 o12 2 Mounting Hole Plug AL-B1PN05 4.4 Nitryl rubber (black) AL-B8PN05 o9 4.2 o8 5 1.8 o10 Replacement Parts for AP1M Shape Type Lens Ordering Type No. Package Quantity Lens Color Code (Specify in place of in the Ordering Type No.) Dome Lens AP1M-L2PN05 A (amber), G (green), R (red), S (blue), W (white), and Y (yellow) (Note 1) Flat Lens AP1M-L1PN05 A (amber), C (clear), G (green), R (red), S (blue), and Y (yellow) (Note 2) Flat Lens AP1M-PN1WPN05 White Dome Lens AP1M-PN2WPN05 White 5 Marking Plate Diffusion Plate Note 1: On the dome lens type, use a white (W) lens for white (W) or pure white (PW) illumination. Note 2: On the flat lens type, use a clear (C) lens for white (W) or pure white (PW) illumination. Dimensions u AP1M Type (o10mm) u AP8M Type (o8mm) 2.2 1.5 2.2 - 21.5 + 8 29.5 Panel Cut-out o12 Flat 5.5 8.5 0. 1 o8 .1 +0 . 0 2 +0 0 .2 o8 5.5 4 10 Panel Cut-out Flat o10 o12 5.5 8 29.5 o1 21.5 o10 5.5 9.5 o9.8 Gasket Dome 3 o8 o9.8 2.8 Gasket 2.8 Panel Thickness 0.8 to 6 Panel Thickness 0.8 to 6 Dome 1.5 9.5 Marking Plate Terminal Arrangement (Bottom View) u AP8M Type (o8mm) u AP1M Type (o10mm) u AP1M Type (o10mm) 7 o7. Projection 6.1 - + Projection Positive Terminal Negative Terminal Positive Terminal Negative Terminal Engraving depth: 0.5 mm maximum Marking plate material: White acrylic 3 o8/o10 AP Series LED Illuminated Miniature Pilot Lights Safety Precautions * Turn off the power to the AP series pilot lights before starting installation, removal, wiring, maintenance, and inspection. Failure to turn power off may cause electrical shocks or fire hazards. * For wiring, use wires of a proper size to meet the voltage and current requirements and solder correctly. Improper soldering may cause overheating and fire. Instructions o Panel mounting When mounting the AP series pilot lights onto a panel, use the optional locking ring wrench (MT-003 or MT-004) to tighten the locking ring. Tightening torque must not exceed 0.29 N*m. Do not use pliers. Excessive tightening will damage the locking ring. o Wiring 1. Note the polarity when wiring the 5V DC versions. 2. A built-in current limiting resistor eliminates the need for external resistors. 3. Solder the terminals using a 60W soldering iron at 350C within 3 seconds. Sn-Ag-Cu type solder is recommended. When soldering, be sure to keep the soldering iron as far away from the housing as possible. Also ensure that no tensile force is applied to the terminal. Do not bend the terminal or apply excessive force to the terminal. Use non-corrosive liquid rosin as soldering flux. o Marking The AP1M flat version contains a white marking plate underneath the lens. The AP1M dome series contains a diffusion plate underneath the lens. The diffusion plate can be removed from the AP1M series, however, this reduces the degree of protection to IP40. Lenses cannot be removed from the AP8M series. Specifications and other descriptions in this brochure are subject to change without notice. 7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan Tel: +81-6-6398-2571, Fax: +81-6-6392-9731 E-mail: products@idec.co.jp IDEC CORPORATION (USA) IDEC ELEKTROTECHNIK GmbH IDEC IZUMI (H.K.) CO., LTD. 1175 Elko Drive, Sunnyvale, CA 94089-2209, USA Tel: +1-408-747-0550 / (800) 262-IDEC (4332) Fax: +1-408-744-9055 / (800) 635-6246 E-mail: opencontact@idec.com Wendenstrasse 331, D-20537 Hamburg, Germany Tel: +49-40-25 30 54 10, Fax: +49-40-25 30 54 24 E-mail: service@idec.de Unit 1505-07, DCH Commercial Centre No. 25, Westlands Road, Quarry Bay, Hong Kong Tel: +852-2803-8989, Fax: +852-2565-0171 E-mail: info@hk.idec.com IDEC CANADA LIMITED Room 608-609, 6F, Gangtai Plaza, No. 700, Yan'an East Road, Shanghai 200001, P.R.C. Tel: +86-21-5353-1000, Fax: +86-21-5353-1263 E-mail: idec@cn.idec.com Unit 22-151, Brunel Road Mississauga, Ontario, L4Z 1X3, Canada Tel: +1-905-890-8561, Toll Free: (888) 317-4332 Fax: +1-905-890-8562 E-mail: sales@ca.idec.com IDEC AUSTRALIA PTY. LTD. 2/3 Macro Court, Rowville, Victoria 3178, Australia Tel: +61-3-9763-3244, Toll Free: 1800-68-4332 Fax: +61-3-9763-3255 E-mail: sales@au.idec.com IDEC ELECTRONICS LIMITED www.idec.com Unit 2, Beechwood, Chineham Business Park, Basingstoke, Hampshire RG24 8WA, UK Tel: +44-1256-321000, Fax: +44-1256-327755 E-mail: sales@uk.idec.com IDEC (SHANGHAI) CORPORATION IDEC (SHANGHAI) CORPORATION IDEC TAIWAN CORPORATION 8F-1, No. 79, Hsin Tai Wu Road, Sec. 1, Hsi-Chih, Taipei County, Taiwan Tel: +886-2-2698-3929, Fax: +866-2-2698-3931 E-mail: service@idectwn.com.tw Beijing Office IDEC IZUMI ASIA PTE. LTD. Unit 1002, No. 10 Kuntai Building, Zhaowai Dajie, Zhao Yang District, Beijing, 100020, P.R.C. Tel: +86-10-6599-5541, Fax: +86-10-6599-5540 No. 31, Tannery Lane #05-01, Dragon Land Building, Singapore 347788 Tel: +65-6746-1155, Fax: +65-6844-5995 E-mail: info@sg.idec.com IDEC (SHENZHEN) CORPORATION Unit AB-3B2, Tian Xiang Building, Tian'an Cyber Park, Fu Tian District, Shenzhen, Guang Dong 518040, P.R.C. Tel: +86-755-8356-2977, Fax: +86-755-8356-2944 Cat. No. EP1117-0 APRIL 2006 15.5DNP PRINTED IN JAPAN