EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 1206 Package Chip LED with Inner lens 11-21SYGC/S530-XX/TR8 Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mono-color type. Pb-free. The product itself will remain within RoHS complaint version Descriptions The 11-21 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications. etc. Applications Automotive: backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Device Selection Guide Part No. 11-21SYGC/S530-XX/TR8 Chip Material Emitted Color AlGaInP Brilliant Yellow Green Lens Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 1 of 9 Device No:SZDSE-111-006 Prepared date: 11-Jul-2005 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 11-21SYGC/S530-XX/TR8 Package Outline Dimensions - + Notes: The tolerances unless mentioned are 0.1, unit=mm. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 2 of 9 Device No:SZDSE-111-006 Prepared date: 11-Jul-2005 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 11-21SYGC/S530-XX/TR8 Absolute Maximum Ratings (Ta=25) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40 ~ +90 Electrostatic Discharge ESD 2000 V Power Dissipation Pd 60 mW IFP 60 mA Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 for 10 sec. Soldering Temperature Tsol Hand Soldering : 350 for 3 sec. Electro-Optical Characteristics (Ta=25) Parameter Symbol Luminous Intensity Iv *Chip Rank Min. Typ. Max. E1 19 29 ----- E2 29 39 ----- E3 39 52 ----- E4 52 62 ----- E5 63 100 ----- Unit Conditio n mcd Viewing Angle 21/2 ----- ----- 60 ----- deg Peak Wavelength Dominant Wavelength Spectrum Radiation Bandwidth p ----- ----- 575 ----- nm d ----- ----- 573 ----- nm ----- ----- 20 ----- nm Forward Voltage VF ----- 1.7 2.0 2.4 V Reverse Current IR ----- ----- ----- 10 A IF=20mA VR=5V *11-21SYGC/S530-XX/TR8 Chip Rank Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 3 of 9 Device No:SZDSE-111-006 Prepared date: 11-Jul-2005 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 11-21SYGC/S530-XX/TR8 Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 4 of 9 Device No:SZDSE-111-006 Prepared date: 11-Jul-2005 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 11-21SYGC/S530-XX/TR8 Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank xxxxxx xxxxxx REF: Forward Voltage Rank RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned are 0.1, Unit = mm. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 5 of 9 Device No:SZDSE-111-006 Prepared date: 11-Jul-2005 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 11-21SYGC/S530-XX/TR8 Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned are 0.1, Unit = mm. Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 6 of 9 Device No:SZDSE-111-006 Prepared date: 11-Jul-2005 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 11-21SYGC/S530-XX/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level : 90 % LTPD : 10 % Test Sample No. Items Test Condition Hours/Cycles Size Temp. : 2605 1 Reflow Soldering 22 PCS. 6 Min. Min. 5sec. 2 3 4 5 Ac/Re 0/1 Temperature Cycle H : +100 15min 5 min L : -40 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100 5min 10 sec L : -10 5min 300 Cycles 22 PCS. 0/1 Temp. : 100 1000 Hrs. 22 PCS. 0/1 Temp. : -40 1000 Hrs. 22 PCS. 0/1 High Temperature Storage Low Temperature Storage 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 7 of 9 Device No:SZDSE-111-006 Prepared date: 11-Jul-2005 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 11-21SYGC/S530-XX/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year.(To fit the MSL-2 .) 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 8 of 9 Device No:SZDSE-111-006 Prepared date: 11-Jul-2005 Prepared by: Wu xiaowei EVERLIGHT ELECTRONICS CO.,LTD. 11-21SYGC/S530-XX/TR8 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 9 of 9 Device No:SZDSE-111-006 Prepared date: 11-Jul-2005 Prepared by: Wu xiaowei