I/O Modules Datasheet PB-8H MOUNTING BOARD * * * * * * Plug-compatible logic connections Screw terminal barrier block for load connections Resident pull-up resistors 5 amp field-replaceable fuses (LITTELFUSE #251005 or equivalent) LEDs indicate logic status All even-numbered logic connections are logic ground Input and output modules accepted interchangeably Operate with 5, 15 or 24 volt logic supplies Captive-screw retaining system for standard-size modules * * * MECHANICAL SPECIFICATIONS SCREW TERMINAL LOGIC SUPPLY BARRIER STRIP REPLACEABLE 1 AMP LOGIC SUPPLY FUSE (see note 4) 8.25 (209,55) DIMENSIONS: INCHES (MILLIMETERS) TOLERANCE:+-0.020 ( +- 0,50) 7.5 (190,5) 0.375 (9,5) 1 AMP FUSE 1 PWR ON +5V GND 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 POWER BARRIER STRIP (see notes 2,3) PIN 49 4.0 (101,6) JUMPERS CONNECTING LOGIC SUPPLY THRU HEADER CONNECTOR 3.5 (88,9) SPARE SWAGED STANDOFF THRU HOLE 0.15 (3,8) DIA. (4) 5A FUSE REPLACEABLE 5 AMP LINE FUSES (8) (see note 5) NEGATIVE (-) LOGIC SUPPLY BUS TERMINATION PIN 1 SPARE 5 AMP LINE FUSE 5V JUMPERS POSITIVE (+) LOGIC SUPPLY BUS TERMINATION 0 1 2 3 4 5 6 7 PULL UP RESISTOR 3.3K OHM (8) 0.65 (16,5) 0.25 (6,4) SIGNAL INPUT/OUTPUT 50 CONDUCTOR MALE PIN CONNECTOR (see note 1) 2.1 (53,3) CRYDOM DIGITAL I/O MODULES SOLD SEPARATELY LED STATUS INDICATORS NOTES: 1) CONNECTOR IS CIRCUIT ASSEMBLY CA-50H-2B-SR OR EQUIVALENT. 2) 6-32 SCREW TERMINAL BARRIER STRIPS ACCEPT WIRE SIZES FROM 24 TO 12 AWG. 3) OPTIONAL JUMPERS ARE AVAILABLE TO INTERCONNECT BARRIER STRIP COMMONS. ORDER 1 EACH "JS8". 4) LITTELFUSE 251001 OR EQUIVALENT. 5) LITTELFUSE 251005 OR EQUIVALENT. LOGIC SUPPLY BARRIER STRIP +5V GND 1 2 3 4 8 9 10 11 12 13 14 15 16 5 6 7 POWER BARRIER STRIP D1 1 AMP LOGIC SUPPLY FUSE 1 49 SIGNAL INPUT/OUTPUT 50 CONDUCTOR MALE PIN CONNECTOR TO G1 BOARD OR RIBBON CABLE APPROVALS UL E79183 5 AMP LINE FUSES (8) PWR ON J1 EVEN 2-50 PINS LOGIC SUPPLY BUS TERMINATION 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 1 1 1 1 1 1 1 2 2 2 2 2 2 2 1 2 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 I/O MODULE PIN SOCKETS NC NC + - Do not forget to visit us at: www.crydom.com Copyright (c) 2016 Crydom Inc. Specifications subject to change without notice. PULL UP RESISTOR 3.3K OHM (8) LED STATUS INDICATORS (8) Rev. 083116 I/O Modules Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. * Disconnect all power before installing or working with this equipment. * Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. * Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. * Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION * Eteindre toutes les sources d'energie de cet appareil avant de travailler dessus de cet appareil * Verifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lesions serieuses serieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. * Stellen Sie jeglichen Strom ab, der dieses Gerat versorgt, bevor Sie an dem Gerat Arbeiten durchfuhren * Vor dem Drehen auf Energie alle Anschlusse uberprufen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen konnen zum Tode oder zu schweren Verletzungen fuhren. RISCHIO DI SCOSSA ELETTRICA O DELL'ESPLOSIONE. * Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa apparecchiatura * * Verificare tutti i collegamenti e sostituire tutte le coperture prima dell'accensione L'omissione di queste istruzioni provochera la morte o lesioni serie WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER GEFAHR VON MATERIALSCHADEN UND GEHAUSEERHITZUNG * The product's side panels may be hot, allow the product to cool before touching. * Follow proper mounting instructions including torque values. * Do not allow liquids or foreign objects to enter this product. * Les panneaux lateraux du produit peuvent etre chauds. Laisser le produit refroidir avant de le toucher. * Respecter les consignes de montage, et notamment les couples de serrage. * Ne pas laisser penetrer de liquide ni de corps etrangers a l'interieur du produit. * Die Seitenwande konnen hei sein. Lassen Sie das Produkt abkuhlen, bevor Sie es beruhren. * Beachten Sie die Montageanweisungen, * Fuhren Sie keine Flussigkeiten oder Fremdkorper in das Produkt ein. Le non-respect de cette directive peut entrainer, Failure to follow these instructions can result in des lesions corporelles graves ou des serious injury, or equipment damage. dommages materiels. Die Nichtbeachtung dieser Anweisung kann Korperverletzung oder Materialschaden zur Folge haben. RIESGO DE DANOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO * Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfrie antes de tocarlo. * Respetar las instrucciones de montaje, y en particular los pares de apretado. * No dejar que penetren liquidos o cuerpos extranos en el producto. * I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. * Seguire le istruzioni di montaggio corrette. * Non far entrare liquidi o oggetti estranei in questo apparecchio. Si no se respetan estas precauciones pueden producirse graves lesiones, danos materiales. La mancata osservanza di questa precauzione puo causare gravi rischi per l'incolumita personale o danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright (c) 2016 Crydom Inc. Specifications subject to change without notice. * * * I/O Modules Datasheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People's Republic of China Electronic Industry Standard SJ/T11364 - 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) Semiconductor die Solder - SJ/T11364 - 2006, (Pb) (Hg) (Cd) (Cr (VI)) 50 Do not forget to visit us at: www.crydom.com Copyright (c) 2016 Crydom Inc. Specifications subject to change without notice. (PBB) (PBDE)