ATR2406-PNQW - ATMEL - Datasheet.Live

4779Q-ISM-09/14

Features

●Fully integrated low IF receiver

●Fully integrated GFSK modulator for 72, 144, 288, 576 and 1152Kbits/s

●High sensitivity of typically –93dBm due to integrated LNA

●High output power of typically +4dBm

●Multi-channel operation

●95 channels

●Support frequency hopping (ETSI) and digital modulation (FCC)

●Supply-voltage range 2.9V to 3.6V (unregulated)

●Auxiliary voltage regulator on chip (3.2V to 4.6V)

●Low current consumption

●Few low-cost external components

●Integrated ramp-signal generator and power control for an additional power amplifier

●Low profile lead-free plastic package QFN32 (5mm × 5mm × 0.9mm)

●RoHs compliant

Applications

●High-tech multi-user toys

●Wireless game controllers

●Telemetry

●Wireless audio/video

●Electronic point of sales

●Wireless head set

●FCC CFR47, part 15, ETSI EN 300 328, EN 300 440 and ARIB STD-T-66

compliant radio links

ATR2406

Low-IF 2.4-GHz ISM Transceiver

DATASHEET

ATR2406 [DATASHEET]

4779Q–ISM–09/14

1. Description

The Atmel® ATR2406 is a single chip RF transceiver intended for applications in the 2.4GHz ISM band.

The QFN32-packaged IC is a complete transceiver including image rejection mixer, low IF filter, FM demodulator, RSSI, TX

preamplifier, power-ramping generator for external power amplifier, integrated synthesizer, and a fully integrated VCO and

TX filter. No mechanical adjustment is necessary in production.

The RF transceiver offers a clock recovery function on-chip.

Figure 1-1. Block Diagram

LNA IR-Mixer

VCO

REG

REG_DEC

RAMP_OUT

TX_OUT

RX_IN

VREG_VCO

REG_CTRL VS_REG

VS_SYN

VREG IREF

CP REF_CLK TX_DATA VTUNE

AUX

REG

AUX

REG

TEST2

PU_REG

PU_TRX

RX_ON

TX_ON

nOLE

CLOCK

DATA

ENABLE

LIMITER

RSSI

DEMOD

RAMP

GEN PLL

GAUSSIAN

FILTER

CTRL

LOGIC

BUS

VCO

VS_IFD

RX_DATA

RSSI

VS_IFA

VS_RX/TX

TEST1

Divider

by 2

ATR2406 [DATASHEET]

4779Q–ISM–09/14

2. Pin Configuration

Figure 2-1. Pinning QFN32 - 5 × 5

Table 2-1. Pin Description

Pin Symbol Function

1PU_REG Power-up input for auxiliary regulator

2REF_CLK Reference frequency input

3RSSI Received signal strength indicator output

4VS_IFD Digital supply voltage

5VS_IFA Analog supply voltage for IF circuits

6RX-CLOCK RX-CLOCK, if RX mode with clock recovery is active

7IC Internally connected. Connect to VS if internal AUX regulator is not used

8IREF External resistor for band-gap reference

9REG_CTRL Auxiliary voltage regulator control output

10 VREG Auxiliary voltage regulator output

11 VS_REG Auxiliary voltage regulator supply voltage

12 REG_DEC Decoupling pin for VCO_REG

13 VREG_VCO VCO voltage regulator

14 VTUNE VCO tuning voltage input

15 CP Charge-pump output

16 VS_SYN Synchronous supply voltage

17 VS_TRX Transmitter receiver supply voltage

18 RX_IN2 Differential receiver input 2

19 RX_IN1 Differential receiver input 1

20 TX_OUT TX driver amplifier output

21 RAMP_OUT Ramp generator output for PA power ramping

22 IC Internally connected, do not connect on PCB

23 IC Internally connected, do not connect on PCB

24 RX_ON RX control input

RX_ON

RAMP_OUT

TX_OUT

RX_IN1

RX_IN2

VS_TRX

RX_ON

RAMP_OUT

TX_OUT

RX_IN1

RX_IN2

VS_TRX

PU_REG

PENABLE

DATA

CLOCK

TX_DATA

RX_DATA

PU_TRX

nOLE

TX_ON

REG_CTRL

VREG

VS_REG

REG_DEC

VREG_VCO

VTUNE

VS_SYN

RSSI

VS_IFD

VS_IFA

RX-CLOCK

IREF

REF_CLK

31 30 29 28 27 26 25

9 10111213141516

ATR2406

ATR2406 [DATASHEET]

4779Q–ISM–09/14

25 TX_ON TX control input

26 NOLE Open loop enable input

27 PU_TRX RX/TX/PLL/VCO power-up input

28 RX_DATA RX data output

29 TX_DATA TX data input

30 CLOCK 3-wire-bus: Clock input

31 DATA 3-wire-bus: Data input

32 ENABLE 3-wire-bus: Enable input

Paddle GND Ground

Table 2-1. Pin Description (Continued)

Pin Symbol Function

ATR2406 [DATASHEET]

4779Q–ISM–09/14

3. Functional Description

3.1 Receiver

The RF signal at RF_IN is differentially fed through the LNA to the image rejection mixer IR_MIXER, driving the integrated

low-IF band-pass filter. The IF frequency is 864kHz. The limiting IF_AMP with an integrated RSSI function feeds the signal to

the digital demodulator DEMOD. No tuning is required. Data slicing is handled internally.

3.2 Clock Recovery

For a 1152Kbit/s data rate, the receiver has a clock recovery function on-chip.

The receiver includes a clock recovery circuit which regenerates the clock out of the received data. The advantage is that

this recovered clock is synchronous to the clock of the transmitting device (and thus to the transmitted data), which

significantly reduces the load of the processing microcontroller.

The falling edge of the clock is the optimal sampling position for the RX_Data signal, so at this event the data must be

sampled by the microcontroller. The recovered clock is available at pin 6.

3.3 Transmitter

The transmit data at TX_DATA is filtered by an integrated Gaussian filter (GF) and fed to the fully integrated VCO operating

at twice the output frequency. After modulation, the signal is frequency divided by 2 and fed to the internal preamplifier PA.

This preamplifier supplies typically +4dBm output power at TX_OUT.

A ramp-signal generator RAMP_GEN, providing a ramp signal at RAMP_OUT for the external power amplifier, is integrated.

The slope of the ramp signal is controlled internally so that spurious requirements are fulfilled.

3.4 Synthesizer

The IR_MIXER, the PA, and the programmable counter (PC) are driven by the fully integrated VCO, using on-chip inductors

and varactors. The output signal is frequency divided to supply the desired frequency to the TX_DRIVER, the 0/90 degree

phase shifter for the IR_MIXER, and to be used by the PC for the phase detector (PD) (fPD = 1.728MHz). Open loop

modulation is supported.

3.5 Power Supply

An integrated band-gap–stabilized voltage regulator for use with an external low-cost PNP transistor is implemented.

Multiple power-down and current saving modes are provided.

ATR2406 [DATASHEET]

4779Q–ISM–09/14

4. Absolute Maximum Ratings

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating

only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this

specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Parameters Symbol Min. Max. Unit

Supply voltage auxiliary regulator VS–0.3 +4.7 V

Supply voltage VS–0.3 +3.6 V

Control voltages Vcontr –0.3 VSV

Storage temperature Tstg –40 +125 °C

Input RF level PRF +10 dBm

ESD protection VESD_ana TBD V

VESD_dig TBD V

5. Thermal Resistance

Parameters Symbol Value Unit

Junction ambient RthJA 35 K/W

6. Operating Range

Parameters Symbol Min. Max. Unit

Supply voltage VS2.9 3.6 V

Auxiliary regulator supply voltage VS_BATT 3.2 4.6 V

Temperature ambient Tamb –10 +60 °C

Input frequency range fRX 2400 2483 MHz

ATR2406 [DATASHEET]

4779Q–ISM–09/14

7. Electrical Characteristics

VS = 3.6V with AUX regulator, Tamb = 25°C, unless otherwise specified

No. Parameters Test Conditions Symbol Min. Typ. Max. Unit

1Supply

1.1 Supply voltage With AUX regulator VS3.2 3.6 4.6 V

1.2 Supply voltage Without AUX regulator VS2.9 3.0 3.6 V

1.3 RX supply current CW mode (peak current) IS57 mA

Burst mode at 10Kbits/s(4) IS625 µA

1.4 TX supply current CW mode (peak current) IS42 mA

Burst mode at 10Kbits/s(4) IS500 µA

1.5

Battery lifetime of a remote

control application using an

AVR®

See Section 11. “Appendix:

Current Calculations for a Remote

Control” on page 21

1.6 Supply current in power-down

mode

With AUX regulator

PU_TRX = 0; PU_REG = 0 IS< 1 µA

1.7 Supply current in power-down

mode

Without AUX regulator

PU_TRX = 0; PU_REG = 0 IS< 1 µA

2Voltage Regulator

2.1 AUX regulator VREG 3.0 V

2.2 VCO regulator VREG_VCO 2.7 V

3Transmitter Part

3.1 TX data rate 72/144/288/576/1152 kBits/s

3.2 Output power PTX 4dBm

3.3 TX data filter clock 9 taps in filter fTXFCLK 10.368/13.824 MHz

3.4 Frequency deviation To be tuned by GFCS bits GFFM_nom ±400 kHz

3.5 Frequency deviation scaling(3) GFFM = GFFM_nom × GFCS

(Refer to bus protocol D9 to D11) GFCS 60 130 %

3.6 Frequency drift

With standard loop filter and slot

length of 1400µs (refer to the

application note “ATR2406 Loop

Filter and Data Rates”)

Dfo (drift) ±40 kHz

3.7 Harmonics BW = 100kHz(1) –41.2 dBm

3.8

Spurious emissions

30 to 1000MHz

1 to 12.75GHz

1.8 to 1.9GHz

5.15 to 5.3GHz

BW = 100kHz(1)

–57

dBm

4Ramp Generator, Pin 21

4.1 Minimum output voltage TX_ON = low Vmin 0.7 V

4.2 Maximum output voltage Refer to bus protocol D12 to D13 Vmax 1.1 1.9 V

4.3 Rise time tr5µs

Notes: 1. Measured and guaranteed only on the Atmel® evaluation board, including microstrip filter, balun, and smart radio fre-

quency (smart RF) firmware. Conducted measured.

2. Timing is determined by external loop filter characteristics. Faster timing can be achieved by modification of the loop fil-

ter. For further information refer to the application notes.

3. The Gaussian filter control setting (GFCS) is used to compensate production tolerances by tuning the modulation devia-

tion in production to the nominal value of 400kHz.

4. Burst mode with 0.9% duty cycle

ATR2406 [DATASHEET]

4779Q–ISM–09/14

4.4 Fall time tf5µs

5Receiver Part

5.1 RX input impedance Differential Zin 170 + j0 Ω

5.2 Sensitivity At input for BER ≤10-3 at

1152Kbits/s(1) –93 dBm

5.3 Third order input intercept point IIP3 –15 dBm

5.4 Intermodulation rejection

BER < 10-3, wanted at –83dBm,

level of interferers in channels

N + 2 and N + 4(1)

IM332 dBc

5.5 Co-channel rejection BER < 10-3, wanted at –76dBm(1) RCO –11 dBc

5.6 Adjacent channel rejection

±1.728MHz

BER < 10-3, wanted at –76dBm,

adjacent level referred to wanted

channel level(1)

Ri (N – 1) 14 dBc

5.7 Bi-adjacent channel rejection

±3.456MHz

BER < 10-3, wanted at –76dBm,

bi-adjacent level referred to

wanted channel level(1)

Ri (N – 2) 30 dBc

5.8

Rejection with ≥ 3 channels

separation

≥±5.128MHz

BER < 10-3, wanted at –76dBm,

n≥3 adjacent level referred to

wanted channel level(1)

Ri (n ≥ 3) 40 dBc

5.9 Out of band rejection > 6MHz BER < 10-3, wanted at –83dBm at

2.45GHz(1) Bldf>6MHz 38 dBc

5.10

Out of band rejection

2300MHz to 2394MHz

2506MHz to 2600GHz

BER < 10-3, wanted at –83dBm at

2.45GHz(1) Blnear 47 dBc

5.11

Out of band rejection

30MHz to 2300MHz

2600MHz to 6GHz

BER < 10-3, wanted at –83dBm at

2.45GHz(1) Blfar 57 dBc

6RSSI Part

6.1 Maximum RSSI output voltage Under high RX input signal level VRSSImax 2.1 V

6.2 RSSI output voltage, monotonic

over range –96dBm to –36dBm

With –33dBm at RF input

With –96dBm at RF input VRSSI

1.9

0.1

7VCO

7.1 Oscillator frequency defined at

TX output Over full temperature range(1) 2400 2483 MHz

7.2 Frequency control voltage

range VVTUNE 0.5 VCC –

0.5 V

7.3 VCO tuning input gain defined

at TX output GVCO 240 MHz/V

7. Electrical Characteristics (Continued)

VS = 3.6V with AUX regulator, Tamb = 25°C, unless otherwise specified

No. Parameters Test Conditions Symbol Min. Typ. Max. Unit

Notes: 1. Measured and guaranteed only on the Atmel® evaluation board, including microstrip filter, balun, and smart radio fre-

quency (smart RF) firmware. Conducted measured.

2. Timing is determined by external loop filter characteristics. Faster timing can be achieved by modification of the loop fil-

ter. For further information refer to the application notes.

3. The Gaussian filter control setting (GFCS) is used to compensate production tolerances by tuning the modulation devia-

tion in production to the nominal value of 400kHz.

4. Burst mode with 0.9% duty cycle

ATR2406 [DATASHEET]

4779Q–ISM–09/14

8Synthesizer

8.1 External reference input

frequency

D7 = 0

D7 = 1 REF_CLK 10.368

13.824

MHz

8.2 Sinusoidal input signal level

(peak-to-peak value) AC-coupled sine wave REF_CLK 500 1000 mVPP

8.3 Scaling factor prescaler SPSC 32/33 -

8.4 Scaling factor main counter SMC 86/87/88/89 -

8.5 Scaling factor swallow counter SSC 031 -

9Phase Detector

9.1 Phase detector comparison

frequency fPD 1728 kHz

10 Charge-pump Output

10.1 Charge-pump output current VCP = 1/2 VCC ICP ±2 mA

10.2 Leakage current VCP = 1/2 VCC IL±100 1000 pA

11 Timing Conditions(1)(2)

11.1 Transmit to receive time Reference clock stable TX → RX time 200 µs

11.2 Receive to transmit time Reference clock stable RX → TX time 200 µs

11.3 Channel switch time Reference clock stable CS time 200 µs

11.4 Power down to transmit Reference clock stable PD → TR time 250 µs

11.5 Power down to receive Reference clock stable PD → RX time 200 µs

11.6 Programming register Reference clock stable PRR time 3µs

11.7 PLL settling time Reference clock stable PLL set time 200 µs

12 Interface Logic Input and Output Signal Levels, Pin DATA, CLOCK, ENABLE

12.1 HIGH-level input voltage Logic 1 VIH 1.4 3.1 V

12.2 LOW-level input voltage Logic 0 VIL –0.3 +0.4 V

12.3 HIGH-level output voltage Logic 1 VOH 3.1 V

12.4 LOW-level output voltage Logic 0 VOL 0 V

12.5 Input bias current Logic 1 or logic 0 Ibias –5 +5 µA

12.6 3-wire bus clock frequency fCLKmax 10 MHz

7. Electrical Characteristics (Continued)

VS = 3.6V with AUX regulator, Tamb = 25°C, unless otherwise specified

No. Parameters Test Conditions Symbol Min. Typ. Max. Unit

Notes: 1. Measured and guaranteed only on the Atmel® evaluation board, including microstrip filter, balun, and smart radio fre-

quency (smart RF) firmware. Conducted measured.

2. Timing is determined by external loop filter characteristics. Faster timing can be achieved by modification of the loop fil-

ter. For further information refer to the application notes.

3. The Gaussian filter control setting (GFCS) is used to compensate production tolerances by tuning the modulation devia-

tion in production to the nominal value of 400kHz.

4. Burst mode with 0.9% duty cycle

ATR2406 [DATASHEET]

4779Q–ISM–09/14

8. PLL Principle

Figure 8-1. PLL Principle

Table 8-1 shows the LO frequencies for RX and TX in the 2.4-GHz ISM band. There are 95 channels available. Since the

ATR2406 supports wideband modulation with 400-kHz deviation, every second channel can be used without overlap in the

spectrum.

Table 8-1. LO Frequencies

Mode fIF/kHz Channel fANT/MHz fVCO/MHz divided by 2 SMC SSC N

C0 2401.056 2401.056 86 27 2779

C1 2401.920 2401.920 86 28 2780

... ... ... ... ... ...

C93 2481.408 2481.408 89 24 2872

C94 2482.272 2482.272 89 25 2873

RX 864

C0 2401.056 2401.920 86 28 2780

C1 2401.920 2402.784 86 29 2781

... ... ... ... ... ...

C93 2481.408 2482.272 89 25 2873

C94 2482.272 2483.136 89 26 2874

"- Main counter MC

"- Swallow counter SC

fCVO = 1728kHz x (SMC x 32 + SSC)

Programmable counter PC

VCO

TXDAT

Baseband controller

Reference counter (RC)

REF_CLK D7

13.824MHz 1

10.368MHz 0

Mixer

PA driver

Gaussian

filter (GF)

Divide

by 2

Charge

pump

External

loop filter

PLL reference frequency

REF_CLK

Phase frequency

detector (PD)

fPD = 1728kHz

ATR2406 [DATASHEET]

4779Q–ISM–09/14

8.1 TX Register Setting

The following 16-bit word has to be programmed for TX.

Note: D12 and D13 are only relevant if ramping generator in conjunction with external PA is used, otherwise it can be

programmed 0 or 1.

The VRAMP voltage is used to control the output power of an external power amplifier. The voltage ramp is started with the

TX_ON signal.

These bits are only relevant in TX mode.

8.2 RX Register Setting

There are two RX settings possible. For a data rate of 1152kBits/s, an internal clock recovery function is implemented.

8.3 Register Setting Without Clock Recovery

Must be used for data rates below 1.152Mbits/s.

Note: X values are not relevant and can be set to 0 or 1.

MSB LSB

Data bits

D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0

01 PA GFCS 1RC MC SC

Table 8-2. Output Power Settings with Bits D12 - D13

PA (Output Power Settings)

D13 D12 RAMP_OUT (Pin 21)

0 0 1.3V

0 1 1.35V

1 0 1.4V

1 1 1.75V

MSB LSB

Data bits

D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0

01XXXXX0RC MC SC

ATR2406 [DATASHEET]

4779Q–ISM–09/14

8.4 RX Register Setting with Internal Clock Recovery

Recommended for 1.152Mbit/s data rate.

The output pin of the recovered clock is pin 6. The falling edge of the recovered clock signal samples the data signal.

Note: X values are not relevant and can be set to 0 or 1.

8.5 PLL Settings

RC, MC and SC bits control the synthesizer frequency as shown in Table 8-3, Table 8-4 on page 12 and Table 8-5 on page

13.

Formula for calculating the frequency:

TX frequency: fANT = 864kHz × (32 × SMC + SSC)

RX frequency: fANT = 864kHz × (32 × SMC + SSC – 1)

MSB

Data bits

D24 D23 D22 D21 D20 D19 D18 D17 D16

10100 0000

LSB

Data bits

D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0

00XXX XX0RC MC SC

Table 8-3. PLL Settings of the Reference Counter Bit D7

RC (Reference Counter)

D7 CLK Reference

010.368MHz

113.824MHz

Table 8-4. PLL Settings of the Main Counter Bits D5 to D6

MC (Main Counter)

D6 D5 SMC

0 0 86

0 1 87

1 0 88

1 1 89

ATR2406 [DATASHEET]

4779Q–ISM–09/14

8.6 GFCS Adjustment

The Gaussian filter control setting (GFCS) is used to compensate for production tolerances by tuning the modulation

deviation in production to the nominal value of 400kHz. These bits are only relevant in TX mode.

8.7 Control Signals

The various transceiver functions are activated by the following control signals. A timing proposal is shown in Figure 8-3 on

page 15.

Table 8-5. PLL Settings of the Swallow Counter Bits D0 to D4

SC (Swallow Counter)

D4 D3 D2 D1 D0 SSC

0 0 0 0 0 0

0 0 0 0 1 1

0 0 0 1 0 2

... ... ... ... ... ...

1 1 1 0 1 29

1 1 1 1 0 30

1 1 1 1 1 31

Table 8-6. GFCS Adjustment of Bits D9 - D11

GFCS

D11 D10 D9 GFCS

0 0 0 60%

0 0 1 70%

0 1 0 80%

0 1 1 90%

1 0 0 100%

1 0 1 110%

1 1 0 120%

1 1 1 130%

Table 8-7. Control Signals and Functions

Signal Functions

PU_REG Activates AUX voltage regulator and the VCO voltage regulator supplying the complete

transceiver

PU_TRX Activates RX/TX blocks

RX_ON Activates RX circuits: DEMOD, IF AMP, IR MIXER

TX_ON Activates TX circuits: PA, RAMP GEN, Starts RAMP SIGNAL at RAMP_OUT

NOLE Disables open loop mode of the PLL

ATR2406 [DATASHEET]

4779Q–ISM–09/14

8.8 Serial Programming Bus

The transceiver is programmed by the SPI (CLOCK, DATA and ENABLE).

After setting the enable signal to low, the data is transferred bit by bit into the shift register on the rising edge of the clock

signal, starting with the MSBit. When the enable signal has returned to high, the programmed information is active.

Additional leading bits are ignored and there is no check made of how many clock pulses arrived during enable low.

The programming of the transceiver is done by a 16-bit or 25-bit data word (for the RX clock recovery mode).

8.9 3-wire Bus Timing

Figure 8-2. 3-wire Bus Protocol Timing Diagram

Table 8-8. 3-wire Bus Protocol Table

Description Symbol Minimum Value Unit

Clock period TPER 100 ns

Set time data to clock TS 20 ns

Hold time data to clock TH 20 ns

Clock pulse width TC 60 ns

Set time enable to clock TL 100 ns

Hold time enable to data TEC 0ns

Time between two protocols TT 250 ns

TTTEC

ENABLE

CLOCK

DATA

TL TCTPER

ATR2406 [DATASHEET]

4779Q–ISM–09/14

Figure 8-3. Example TX and RX Timing Diagram

Power up Programming Programming Active TX slotActive RX slot Power down

optional

Power up

optional

Power down

> 40μs

> 200μs

> 40μs

> 50μs

Data

Pin name

MODE

PU_REG

Pin 1

PU_TRX

Pin 27

TX_DATA

Pin 29

3W_CLK

Pin 30

3W_DATA

Pin 31

3W_ENA

Pin 32

nOLE

Pin 26

REF_CLK

Pin 2

RX_ON

TRX (Output)

Signals fromSignals to TRX (Input)

Pin 24

TX_ON

Pin 25

RX_DATA

Pin 28

RSSI

Pin 3

RAMP_OUT

Pin 21

connected to

RAMP_IN of

optional PA Note: 1. Keep input signals at low level during power-down state of TRX

C3 C4 C1

C1 C2 C5

16/25 bits

> 200μs

Preamble

(1-0-1-0)

16 bits

REF_CLK

Valid signal

ATR2406 [DATASHEET]

4779Q–ISM–09/14

8.10 Received Signal Strength Indication (RSSI)

The RSSI is given as an analog voltage at the RSSI pin. A typical plot of the RSSI value is shown in Figure 8-4.

Figure 8-4. Typical RSSI Value versus Input Power

Table 8-9. Description of the Conditions/States

Condition Description

C1 Power down

ATR2406 is switched off and the supply current is lower than 1µA.

Power up

ATR2406 is powered up by toggling PU_REG and PU_TRX to high.

PU_REG enables the external AUX regulator transistor including VCO regulator. PU_TRX

enables internal blocks like the PLL and the VCO.

Depending on the value of the external capacitors (for example, at the AUX regulator, if one is

used), it is necessary to wait at least 40µs until the different supply voltages have settled.

Programming

The internal register of the ATR2406 is programmed via the three-wire interface. At TX, this is just

the PLL (transmit channel) and the deviation (Gaussian filter).

At RX, this is just the PLL (receive channel) and, if the clock recovery is used, also the bits to

enable this option. At the start of the three-wire programming, the enable signal is toggled from

high to low to enable clocking the data into the internal register. When the enable signal rises

again to high, the programmed data is latched. This is the time point at which the settling of the

PLL starts. It is necessary to wait the settling time of 200µs so that the VCO frequency is stable.

The reference clock needs to be applied to ATR2406 for at least the time when the PLL is in

operation, which is the programming state (C3) and the active slot (C4, C5). Out of the reference

clock, several internal signals are also derived, for example, the Gaussian filter circuitry and

TX_DATA sampling.

C4 This is the receive slot where the transmit burst is received and data as well as recovered clock

are available.

This is the active transmit slot. As soon as TX_DATA is applied to ATR2406, the signal nOLE

toggles to low which enables modulation in open-loop mode.

The preamble (1-0-1-0 pattern) should start being sent at the start of TX_ON.

-130 -110 -90 -70 -50 -30 -10 10

RF Level (dBm)

2.5

2.0

1.5

1.0

0.5

RSSI Level (V)

ATR2406 [DATASHEET]

4779Q–ISM–09/14

9. Application Circuit

The Atmel® ATR2406 requires only a few low-cost external components for operation. A typical application is shown in

Figure 9-3 on page 18.

9.1 Typical Application Circuit

Figure 9-1. Microcontroller Interfacing with General Purpose MCU, Pin Connections between Microcontroller and

ATR2406

Figure 9-2. Example with AVR MCU

Note: 1. XTAL: for example, XRFBCC-NANL; 13.824MHz, 10ppm

Order at: Taitien Electronic, Taitien Specific No.: A009-x-B26-3, SMD

Microcontroller ATR2406

Configuration

and control

RF-DATA

Interface

TX_DATA

RX_DATA

RX-CLOCK

DATA

CLOCK

ENABLE

Ctrl_Lines

XTAL_OUT REF_CLK

XTAL(1)

ATR2406

RF_CTRL

RF_DATA

AVR_MCU

USART

GPIO

13.824MHz XTAL REF_CLK

nOLE

ENABLE

CLOCK

DATA

TX_ON

RX_ON

PU_TRX

PU_REG

GPIO1

GPIO2

TXD

RXD

XCK

GPIO3

GPIO4

GPIO5

TX_DATA

RX_DATA

RX-CLOCK

RSSI

ATR2406 [DATASHEET]

4779Q–ISM–09/14

Figure 9-3. Application Circuit for ATR2406-DEV-BOARD

2.2pF

5.6pF

25 G

TP2TP1

RX_DATA

RSSI

RX_CLOCK

REF_CLK

PU_REG

ENABLE

DATA

CLOCK

nOLE

PU_TRX

RAMP_OUT

RX_ON

VBATT

TX_DATA

CLOCK

TX_DATA

ENABLE

VS_IFA

VS_IFD

RSSI

REF_CLK

IREF

RX_CLOCK

PU_REG

TX_OUT

RAMP_OUT

VS_TRX

RX_IN2

RX_IN1

RX_ON

DATA

RX_DATA

PU_TRX

TX_ON

nOLE

REG_DEC

VREG_VCO

REG_CTRL

VS_REG

VREG

VTUNE

GND

VS_SYN

TX_ON

1.5pF

1.8pF

C24

C13

4.7μF

C12

100nF

C15

100nF

C16

4.7pF

4.7μF

C17

390pF

C29

4.7nF

C11

BC808

18pF

1.8pF

C10

R2 NC

J24

RSSI

RX_ON

CLOCK

PU_TRX

TX_DATA

TX_ON

VBATT

J10

REF_CLK

J4 J11

J12

J13

J14

J20

J19

J18

J17

J16

J15

VBATT

ENABLE

DATA

nOLE

RX_DATA

RX_CLOCK

PU_REG

SMASI

GND

ANT2

ANT

F antenna

Select integrated F antenna or

SMA connector by setting the

0 resistor

ANT GND

Microstrip

balun

Microstrip

ATR2416

Microstrip

Low-passfilter

C14

GND5

GND4

GND9

GND8

GND7

GND2

GND3

GND1

GND6

IC2

RFOUT (Ant)

1kΩ

1.5kΩ

62kΩ

C21

J26

C20, C21, COG

dielectric

C18 2.2nF

68pF

C19

470nF

C20

IC2P

GND

Slug

22nF

RAMP

J21

ATR2406 [DATASHEET]

4779Q–ISM–09/14

10. PCB Layout Design

Figure 10-1. PCB Layout ATR2406-DEV-BOARD

ATR2406 [DATASHEET]

4779Q–ISM–09/14

Table 10-1. Bill of Materials

Part Value Part Number Vendor Package Comment

C1 5.6pF 0402

C3, C10 1.8pF 0402

C4 390pF 0402

C5 4.7pF 0402 NC

C6, C7 2.2pF 0402

C9 1.5pF 0402

C11 18pF 0402

C12, C15 100nF 0402

C13, C16 4.7µF B45196H2475M109 Epcos®3216 Optional(2)

C14 1nF 0402 NC

C17 3.3nF 0402 NC

C18 68pF 0402

C19 470nF 0402/0603

C20 22nF, COG GRM21B5C1H223JA01 Murata 0805 COG, important for good

RF performance

C21 2.2nF, COG GRM1885C1H222JA01 Murata 0603 COG, important for good

RF performance

C23 4.7nF 0402

C24 4.7pF 0402

R3 62kΩ62k, ≤ 5% 0402

R4 1.0kΩ1k0, ≤ 5% 0402

R5 1.5kΩ1k5, ≤ 5% 0402 Ref_Clk level, optional(1)

R6 1.5kΩ1k5, ≤ 5% 0402 Ref_Clk level, optional(1)

IC2 ATR2406 ATR2406 Atmel MLF32

T1 BC808-40 BC808-40, any standard type can be

used, but it is important that be “–40”!

Vishay®,

Philips®, etc. SOT-23 Optional(2)

MSUB FR4 FR4, e_r = 4.4 at 2.45GHz, H = 500µm, T = 35µm, tand = 0.02, surface, that is, chem. tin or chem.

gold

Notes: 1. Not necessary if supplied RefClk level is within specification range

2. If no AUX regulator is used, then T1 and C16 can be removed and a jumper is needed from the collector to the

emitter pad. Additionally, pin 7 of the ATR2406 has to be connected to pin 4 or pin 5 to use the integrated F

antenna, set jumper R2 (0R resistor 0603)

Table 10-2. Parts Count Bill of Materials

Parts Count Required (Minimal BOM) Optional (Depending on Application)

Capacitors 0402 14 14

Capacitors >0402 2 4

Resistors 0402 2 2

Inductors 0402 – –

Semiconductors 1 2

ATR2406 [DATASHEET]

4779Q–ISM–09/14

11. Appendix: Current Calculations for a Remote Control

Assumptions:

Basic Numbers:

Amount of Current Needed to Transmit One Packet:

Protocol

A data packet consists of 24 bytes.

24 bytes = 240bits (USART connection)

Tpacket_length = 210µs at 1.152Mbits/s

Channel The system will use five predefined channels for frequency hopping spread spectrum

(FHSS) which gives improved immunity against interferers

Loop filter Loop filter settling time will be 110µs

Handheld device

If not in use, the handheld device will be in power-down mode with the AVR® watchdog

timer disabled. The AVR power-down current is typically 1.25µA. If an external voltage

regulator is used, additional power-down current has to be taken into account

Base station device

The base station will periodically scan all the channels of the used subset. The base station

will stay on one channel for 2 seconds. If the base station receives a correct packet, an

acknowledge will be returned to the handheld device. The power consumption of the base

station device is not power-sensitive, as this part of the application is normally mains

powered

Peak current ATR2406 in TX at 1.152Kbits/s 42mA

Peak current ATR2406 in RX at 1.152Kbits/s 57mA

Peak current ATR2406 with synthesizer running 26mA

Current ATmega88 active 5mA

Current ATmega88 power down (no WDT) 1.25µA

Current ATmega88 power down (+ WDT) 5µA

Loop settling time of ATR2406 110µs

Configuration of ATR2406 30µs

Time needed for exchanging a packet at 1.152Kbits/s 210µs

Q1 = (0.005A + 0.026A) ×5030µs = 155µAs (charge up time ATR2406 + AVR internal calculations)

Q2 = (0.005A + 0.026A) ×30µs = 0.93µAs (charge for configuring the ATR2406)

Q3 = (0.005A + 0.026A) ×110µs = 3.41µAs (charge for settling the loop filter)

Q4 = (0.005A + 0.042A) ×210µs = 9.87µAs (charge for transmitting the packet)

Q5 = (0.005A) ´ 250 µs = 1.25µAs (charge for turn around (TX to RX, RX to TX, etc.))

Q6 = (0.005A + 0.026A) ×30µs = 0.93µAs (charge for configuring the ATR2406)

Q7 = (0.005A + 0.026A) ×60µs = 1.86µAs (charge for settling the loop filter)

Q8 = (0.005A + 0.057A) ×50µs = 3.10 µAs (charge until valid data can be received)

Q9 = (0.005A + 0.057A) ×210µs = 13.02µAs (charge for receiving the packet)

Q10 = (0.005A + 0.057A) ×50µs = 3.1µAs (charge for latency before receiving)

ATR2406 [DATASHEET]

4779Q–ISM–09/14

A successful packet exchange needs the following charge

Q=Q1+Q2+Q3+Q4+Q5+Q6+Q7+Q8+Q9+Q10=192.47µAs

As the described system is a FHSS system with 5 different channels, the system has to do this up to five times before the

packet is acknowledged by the base station. The average will be 2.5 times. In the case of an interfered environment, some

more retries may be required; therefore, it is assumed the factor will be 3. The power-up time is included only once, as the

cycle will be completed without powering up and down the handheld in order to be as power efficient as possible.

Average current needed for a packet exchange:

155µAs + (37.5µAs ×3) = 267.5µAs

If the device will be used 1000 times a day →3.1µA

Average current in active mode:

→ System power down current:

Current ATmega88: 1.25µA

Current ATR2406: 1.0µA

Current VREG (+ ShutDown): 2.75µA

Assumed average power-down current is 5µA.

→ Overall power consumption is 8.1µA

It is assumed the system uses a small battery with a capacity of 100mAh. This is 100.000µAh.

→ Battery lifetime will be around: 12345 hours = 514 days = 1.4 years.

The most important factor is to get the power-down current as low as possible!

Example:

Assume a system where the handheld is used just 10 times per day.

→ Iactive = 0.031µA

and assuming the power-down current of this device is just 4 µA.

→ I = 0.031µA + 4µA = 4.03µA

→ Battery lifetime will be around 24807 hours = 1033 days = 2.83 years.

→ Power-down current is the main factor influencing the battery lifetime.

ATR2406 [DATASHEET]

4779Q–ISM–09/14

13. Package Information

12. Ordering Information

Extended Type Number Package Remarks MOQ

ATR2406-PNQW QFN32 - 5x5 Taped and reeled, Pb-free 6000

Package Drawing Contact:

packagedrawings@atmel.com

GPC DRAWING NO.

REV. TITLE

6.543-5203.01-4 1

05/20/14

Package: QFN_5x5_32L

Exposed pad 3.6x3.6

COMMON DIMENSIONS

(Unit of Measure = mm)

MIN NOM NOTEMAXSymbol

Dimensions in mm

specifications

according to DIN

technical drawings

0.035 0.050A1

55.14.9E

0.25 0.30.2b

0.5e

0.4 0.450.35L

3.6 3.73.5E2

3.6 3.73.5D2

55.14.9D

0.21 0.260.16A3

0.85 0.90.8A

Z 10:1

PIN 1 ID

Top View

Side View

Bottom View

32 25

ATR2406 [DATASHEET]

4779Q–ISM–09/14

14. Recommended Footprint/Landing Pattern

Figure 14-1. Recommenced Footprint/Landing Pattern

Table 14-1. Recommended Footprint/Landing Pattern Signs

Sign Size

A3.2mm

B1.2mm

C0.3mm

a1.1mm

b0.3mm

c0.2mm

d0.55mm

e0.5mm

ATR2406 [DATASHEET]

4779Q–ISM–09/14

15. Revision History

Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this

document.

Revision No. History

4779Q-ISM-09/14 • Section 11 “Ordering Information” on page 23 updated

• Section 12 “Package Information” on page 23 updated

4779P-ISM-09/14 • Section 11 “Ordering Information” on page 23 updated

4779O-ISM-03/14 • Put datasheet in the latest template

4779N-ISM-12/08 • Put datasheet in the latest template

• Section 12 “Package Information” on page 22 updated

4779M-ISM-02/07 • Put datasheet in the latest template

• Table 9-1 “Bill of Materials” on page 19 updated

4779L-ISM-08/06

• Table “Electrical Characteristics” on pages 6 to 8 updated

• Section 10 “Appendix: Current calculations for a remote control” on pages 20 to 21

updated

• Table “Ordering Information” on page 22 updated

• Minor corrections to grammar and style throughout document

4779K-ISM-06/06

• Put datasheet in a new template

• Table “Electrical Characteristics” on pages 6 to 8 updated

• Section 10 “Appendix: Current calculations for a remote control” on pages 20 to 21

added

• Ordering information on page 22 updated

XXX

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com

Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR®, and others are registered trademarks or trademarks of Atmel Corporation or its

subsidiaries. Other terms and product names may be trademarks of others.

DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right

is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE

ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT

SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES

FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this

document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information

contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,

authorized, or warranted for use as components in applications intended to support or sustain life.

SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where

the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written

consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.

Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are

not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.