Amplifier Mezzanine Card User Guide
UG-1224
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 •
www.analog.com
Amplifier Mezzanine Card for ADC Drivers
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 14
FEATURES
Enables quick breadboarding and prototyping
User defined circuit configuration
Easy connection to other ADC evaluation boards
COMPATIBLE PULSAR EVALUATION BOARDS
10-lead PulSAR® evaluation board
GENERAL DESCRIPTION
The Analog Devices, Inc., amplifier mezzanine card (AMC)
analog-to-digital converter (ADC) driver evaluates the
performance of amplifiers in 8-lead, single and dual SOIC, 6-
lead single SOT23, 8-lead dual MSOP, and 16-lead LFCSP
packages. This add on board can be inserted on ADC
evaluation boards using its 7-pin header. Figure 1 shows the
AMC mounted on an Analog Devices, Inc., ADC evaluation
board.
The AMC can support any of Analog Devices operational
amplifiers and ADC drivers in different packages. The user can
configure the ADC driver as a Sallen-Key low-pass, high-pass, or
band-pass filter, as a multiple feedback low-pass, high-pass, or
band-pass filter, or as an inverting and noninverting operational
amplifier. The user can also configure the AMC to drive a single-
ended, fully differential, or a single-ended signal to a differential
ADC.
Optimized power and ground planes ensure low noise and high
speed operation. Component placement and power supply
bypassing are optimized for maximum circuit flexibility and
performance. The AMC evaluation board accepts 0402 or 0603
surface mount technology (SMT) components, 1206 bypass
capacitors, and 2.54 mm headers.
All components are placed on the primary side. No components
are placed on the secondary side.
EVALUATION BOARD PHOTOGRAPH
Figure 1.
16423-001
UG-1224 Amplifier Mezzanine Card User Guide
Rev. 0 | Page 2 of 14
TABLE OF CONTENTS
Features .............................................................................................. 1
Compatible PulSAR Evaluation Boards ........................................ 1
General Description ......................................................................... 1
Evaluation Board Photograph ......................................................... 1
Revision History ............................................................................... 2
Board Assembly ................................................................................ 3
Introduction .................................................................................. 3
Single Amplifier ............................................................................ 3
Dual Amplifier .............................................................................. 7
Fully Differential Amplifier .........................................................9
Differential Input Configuration ................................................9
Multiple Feedback LPF Configuration .......................................9
Schematic, Assembly Drawings, and Board Layout .................. 10
8-Lead SOIC Single AMC Schematic ...................................... 10
6-Lead SOT23 Single AMC Schematic ................................... 11
8-Lead MSOP and SOIC Dual AMC Schematic .................... 12
16-Lead LFCSP Fully Differential AMC Schematic .............. 13
REVISION HISTORY
1/2019—Revision 0: Initial Version
Amplifier Mezzanine Card User Guide UG-1224
Rev. 0 | Page 3 of 14
BOARD ASSEMBLY
INTRODUCTION
The AMC allows the user to set the ADC driver to different types
of active filter configurations and op amp layouts such as inverting
and noninverting. The user can also configure the AMC to drive a
single-ended, fully differential, and a single-ended signal to
differential ADC.
SINGLE AMPLIFIER
The AMC for single amplifiers can support ADC drivers that come
in 8-lead SOIC and 6-lead SOT23 packages (see Figure 2 and
Figure 3).
Figure 2. Example of a Single Amplifier in SOIC Package
Figure 3. Example of a Single Amplifier on SOT23 Package
Low-Pass Filter
The user can configure a Sallen-Key, low-pass filter on the AMC.
Figure 4. Sallen-Key, Low-Pass Filter
Place user defined capacitors on the R7 and R8 resistors, user
defined capacitors on the C3 and C4 board positions, and resistors
on the R1, R2, R3, R4, R9, R10, R17, and R18 resistors. Place a
0 Ω resistor on C5 and C6 for the feedback to achieve the
Sallen-Key low-pass filter configuration.
Figure 5. Sallen-Key, Low-Pass Filter for 8-Lead SOIC, Single Board
Connections
Figure 6. Sallen-Key, Low-Pass Filter for 6-Lead SOT23, Single Board
Connections
NC
1
–IN
2
+IN
3
–
V
S4
POWER DOW N
8
+V
S
7
V
OUT
6
NC
5
(Not to Scale)
TOP VIEW
16423-019
V
OUT 1
–V
S2
+IN
3
+V
S
6
POWER DOWN
5
–IN
4
16423-020
R1
IN C1 OUT
R3
R4
C2
R2
16423-021
16423-02216423-023
UG-1224 Amplifier Mezzanine Card User Guide
Rev. 0 | Page 4 of 14
Multiple Feedback, Low-Pass Filter
The user can configure a multiple feedback, low-pass filter on
the AMC.
Place a 0 Ω resistor on R7 and R8 to connect the noninverting
input to ground, and place the user defined capacitors on the
C1, C2, C5, and C6 capacitors and the resistors on the R15, R16,
R17, R18, R19, and R20 resistors.
Figure 7. Multiple Feedback, Low-Pass Filter
Figure 8. Multiple Feedback, Low-Pass Filter for 8-Lead SOIC, Single Board
Connections
Figure 9. Multiple Feedback, Low-Pass for 6-Lead SOT23, Single Board
Connections
High-Pass Filter
Place capacitors on the R1, R2, R3, and R4 resistors, resistors on
the R7, R8, R9, R10, R17, and R18 resistors, and resistors on the C3
and C4 capacitors. Place a 0 Ω resistor on C5 and C6 to configure
the AMC board into a Sallen-Key high-pass filter. This
configuration is similar to the low-pass filter except replace the
resistors on the noninverting input to capacitors and vice versa.
Figure 10. Sallen-Key, High-Pass Filter
Figure 11. Sallen-Key, High-Pass Filter for 8-Lead SOIC, Single Board
Connections
Figure 12. Sallen-Key, High-Pass Filter for 6-Lead SOT23, Single Board
Connection
For the multiple feedback, high-pass filter configuration, place
the user defined capacitors on the R15, R16, R17, R18, R19, and
R20 resistors, resistors on the R9 and R10 resistors, and resistors
on the C5 and C6 capacitors. Place a 0 Ω resistor on R7 and R8.
Figure 13. Multiple Feedback, High-Pass Filter
R1
IN
C5
OUT
R3
C2
R4
16423-024
16423-02516423-026
C1
IN R1 OUT
R3
R4
R2
C2
16423-027
16423-02816423-029
C1
R5
C3
C4
OUT
IN
R2
16423-030
Amplifier Mezzanine Card User Guide UG-1224
Rev. 0 | Page 5 of 14
Figure 14. Multiple Feedback, High-Pass Filter for 8-Lead SOIC, Single Board
Connections
Figure 15. Multiple Feedback, High-Pass Filter for 6-Lead SOT23, Single Board
Connections
Band-Pass Filter
In a Sallen-Key, band-pass filter, place capacitors on the R3, R4,
R5, and R6 resistors, resistors on the R1, R2, R7, R8, R9, R10,
R13, and R14 resistors, and resistors on the C3 and C4
capacitors. Place a 0 Ω resistor on C5 and C6 and put a jumper
on P3 to short VCM to ground.
Figure 16. Sallen-Key, Band-Pass Filter
Figure 17. Sallen-Key, Band-Pass Filter for 8-Lead SOIC, Single Board
Configuration
Figure 18. Multiple Feedback, Band-Pass Filter
Figure 19. Multiple Feedback, Band-Pass Filter for 8-Lead SOIC, Single Board
Connections
To achieve a multiple feedback, band-pass filter, place capacitors on
the R17, R18, R19, and R20 resistors, resistors on the R9, R10,
R15, and R16 resistors, and resistors on the C5 and C6 capacitors.
Place a 0 Ω resistor on R7 and R8.
16423-03116423-032
R1
IN
OUT
R3
R4
R5
C2
R2 C1
16423-033
16423-034
R1
R5
C3
C4
OUT
IN
R2
16423-035
16423-036
UG-1224 Amplifier Mezzanine Card User Guide
Rev. 0 | Page 6 of 14
Inverting Configuration
For the inverting configuration, place 0 Ω resistors on R7, R8,
R15, and R16. Place the user defined resistor values to set the
gain of the amplifier on R9 and R10 for RF and R17 and R18 for
RG.
Figure 20. Inverting Amplifier
Figure 21. Inverting Amplifier for 8-Lead SOIC, Single Board Configuration
Figure 22. Inverting Amplifier for 6-Lead SOT23, Single Board Configuration
Noninverting Configuration
To configure the AMC board into a noninverting amplifier,
place 0 Ω resistors at R1, R2, R3, and R4 to connect the input to
the noninverting input of the amplifier. To set the gain of the
amplifier, place the user defined resistor values on R9 and R10
for RF and R17 and R18 for RG and place a 0 Ω resistor on C5 and
C6 to connect RG to ground.
Figure 23. Noninverting Amplifier Configuration
Figure 24. Noninverting Amplifier for 8-Lead SOIC, Single Board
Configuration
Figure 25. Noninverting Amplifier Configuration for 6-Lead SOT23, Single
Board Configuration
R
IN
V
IN
V
OUT
R
F
16423-037
16423-03816423-039
OP AMP R
F
R
G
V
IN
V
OUT
G = V
OUT
/V
IN
= 1 + (R
F
/R
G
)
16423-040
16423-04116423-042
Amplifier Mezzanine Card User Guide UG-1224
Rev. 0 | Page 7 of 14
DUAL AMPLIFIER
The AMC also supports dual amplifiers that can aid op amps
and ADC drivers that come in 8-lead MSOP and 8-lead SOIC
packages. Dual amplifier have two amplifiers inside one
package.
Figure 26. Dual Amplifier, 8-Lead MSOP (RM) and 8-Lead SOIC (R) Package
Low-Pass Filter
Similar to single amplifiers, the user can configure the dual
amplifier to different types of filter topologies except instead of
two ICs, the user only uses one IC.
Figure 27. Sallen-Key, Low-Pass Filter 8-Lead SOIC, Dual Board Configuration
Figure 28. Sallen-Key, Low-Pass Filter 8-Lead MSOP, Dual Board
Configuration
A Sallen-Key, low-pass filter can also be configured on the dual
AMC. To set the cutoff frequency of the filter, place the user
defined resistor values for the filter on R1 and R3 on one
amplifier and R2 and R4 for the other one. Place the user defined
capacitor values on R7 and C3 for the first amplifier and R8 and C4
for the second amplifier. To set the gain of the amplifier, place
the necessary feedback resistors on R9 and R10 for the first and
second amplifiers, as well as RG on R17 and R18. Then, place a 0 Ω
resistor on C5 and C6 to connect RG straight to ground.
Figure 29. Multiple Feedback Low-Pass Filter 8-Lead SOIC, Dual AMC
Configuration
Figure 30. Multiple Feedback, Low-Pass Filter 8-Lead MSOP, Dual AMC
Configuration
For a multiple feedback configuration, place the user defined
resistor values on R15, R17, and R19 for the first amplifier and R16,
R18, and R20 for the second amplifier. Place the capacitors on
C1 and C5 for the first amplifier and C2 and C6 for the second
amplifier.
High-Pass Filter
To achieve a Sallen-Key, high-pass filter configuration, place a
0 Ω resistor at C5 and C6, then place the user defined resistor
values for the gain setting on R9 and R10 (RF) and R17 and R18
(RG). Place resistors on R7, R8, C3, and C4 as well as capacitors
on R1, R2, R3, and R4 to dictate the cutoff frequency. The
configuration is almost the same as in Sallen-Key, low-pass filter,
but the resistors and capacitors interchange in the noninverting
input of the amplifier.
In the case of a multiple feedback, high-pass filter, place the 0 Ω
resistor on R7 for the first amplifier and R8 for the second. Then,
place the user defined resistor values on C5 and R9 for the first
amplifier and C6 and R10 for the second amplifier. Then, place
capacitors on R15, R17, and R19 for the first amplifier and on
R16, R18, and R20 for the second amplifier.
1
2
3
4
–IN1
+IN1
–V
S
OUT1
8
7
6
5
OUT2
–IN2
+IN2
+V
S
(Not to Scale)
TOP VIEW
16423-043
16423-04416423-045
16423-04616423-047
UG-1224 Amplifier Mezzanine Card User Guide
Rev. 0 | Page 8 of 14
Band-Pass Filter
For a band-pass filter in a Sallen-Key configuration, connect
VCM to ground and place the user defined resistor values to design
the filter on R1, R2, R7, R8, C3, C4, R4, R3, R5, and R6. To set
the gain of the amplifier, place RF on R9 and RG on R13. Do the
same for the second amplifier with RG on R14 and RF on R10.
Figure 31. Sallen-Key, Band-Pass Filter for 8-Lead MSOP, Dual Board
Configuration
Figure 32. Sallen-Key, Band-Pass Filter for 8-Lead SOIC, Dual Board Configuration
In the case for multiple feedback, band-pass filters, mount a 0 Ω
resistor on R7 and R8. Place the user defined resistor values on R9,
R10, R15, R17, C5, and C6. As well as the user defined capacitors
values on R17, R18, R19, and R20 (see Figure 44).
Figure 33. Multiple Feedback, Band-Pass Filter for 8-Lead MSOP,
Dual Board Configuration
Figure 34. Multiple Feedback, Band-Pass Filter for 8-Lead SOIC, Dual Board
Configuration
Inverting Configuration
Place 0 Ω resistors on R7, R8, R15, and R16. Set the gain of the
amplifier with R9 and R10 for RF and R17 and R18 for RG.
Figure 35. Inverting Amplifier for 8-Lead MSOP, Dual Board Configuration
Noninverting Configuration
Place 0 Ω resistors on R1, R2, R3, and R4 to connect the input
to the noninverting input of the amplifier. Set the gain with R9 and
R10 for RF and R17 and R18 for RG and place a 0 Ω resistor on C5
and C6 to connect RG to ground.
Figure 36. Noninverting Amplifier for 8-Lead SOIC, Dual Board Configuration
16423-04816423-04916423-050
16423-05116423-05216423-053
Amplifier Mezzanine Card User Guide UG-1224
Rev. 0 | Page 9 of 14
FULLY DIFFERENTIAL AMPLIFIER
The AMC for fully differential amplifiers supports 16-lead LFCSP
packages. Two basic configurations are shown in Figure 37 and
Figure 38. For additional configurations, refer to the schematic in
Figure 49.
DIFFERENTIAL INPUT CONFIGURATION
Figure 37. Standard Differential Input Configuration
Figure 38. Multiple Feedback, Low Pass Filter Configuration
Install 0 Ω resistors on R1, R2, R5, R6, R11, R12, L1, and L2.
Install 0 Ω resistors on R27, R28, R30, and R23. Install a 0.1 μF
capacitor on C7. Install supply bypass capacitors on C8 and C9.
C3 and C4 are the feedback resistors. R7 and R8 are the gain
resistors. Install jumpers on the second and third positions on
the MODE jumper and CLAMPH jumper (see Figure 37).
MULTIPLE FEEDBACK LPF CONFIGURATION
Fully differential amplifier based, multiple feedback, low-pass
filters (LPFs) can be designed using an op-amp based, multiple
feedback filter configuration, as shown in Figure 39.
Figure 39. Multiple Feedback, Low Pass Filter
Install 0 Ω resistors on R1, R4, R11, R12, L1, L2, R27, R28, R30,
and R23. Install a 0.1 μF capacitor on C7. Install jumpers on the
second and third positions on the MODE jumper and
CLAMPH jumper (see Figure 38).
16423-054
16423-056
R7, R8
C3, C4
2xC1
R5, R6
R9, R10
IN
OUT
16423-055
UG-1224 Amplifier Mezzanine Card User Guide
Rev. 0 | Page 10 of 14
SCHEMATIC, ASSEMBLY DRAWINGS, AND BOARD LAYOUT
8-LEAD SOIC SINGLE AMC SCHEMATIC
Figure 40. 8-Lead SOIC, Single AMC Schematic
Figure 41. 8-Lead SOIC, Single AMC Assembly Drawing, Primary Side
Figure 42. 8-Lead SOIC, Single AMC Layout Pattern, Primary Side
7
4
8
3
6
2
7
4
8
3
6
2
C5
C6
R15 R17
VCM
VCM
R13
R22
R14
R18
R4
R19 VCC
C13 C14
VEE
C1
R9
R20
C2
R10
R1
R16
VINN
R2
R3 R21
VN
VP VS–
PD VO
VS+
VN
VP VS–
PD VO
VS+
R11 VOUTP PD1
P5
VEE VCC
C17 R26
R28
R29
VOUTN
VOUTP
PD-IN
P2
C7
R12 VOUTN
C8
R5
R7
C3
C3
VCM
R6
R8
VCM
VINP
P1 VINN
VINP
R25
R23 R24 VCM
P3
C11 C12
V
CC
V
EE
VCC
C15 C16
VEE
VEE C18 R27
VEE
VCC
P6
PD2
VEE
VEE
C10
P3
C9
VCC
16423-010
16423-011
16423-012
Amplifier Mezzanine Card User Guide UG-1224
Rev. 0 | Page 11 of 14
6-LEAD SOT23 SINGLE AMC SCHEMATIC
Figure 43. 6-Lead SOT23, Single AMC Schematic
Figure 44. 6-Lead SOT23, Single AMC Assembly Drawing, Primary Side
Figure 45. 6-Lead SOT23, Single AMC Layout Pattern, Primary Side
6
2
5
3
1
4
6
2
5
3
1
4
C5
C6
R15 R17
VCM
VCM
R13
R22
R14
R18
R4
R19 VCC
C13 C14
VEE
C1
R9
R20
C2
R10
R1
R16
VINN
R2
R3 R21
VN
VP VS–
PD
IC1
IC2
VO
VS+
VN
VP VS–
PD VO
VS+
R11 VOUTP PD1
P5
VEE VCC
C17 R26
R28
R29
VOUTN
VOUTP
PD-IN
P2
C7
R12 VOUTN
C8
R5
R7
C3
C4
VCM
R6
R8
VCM
VINP
P1 VINN
VINP
R25
R23 R24 VCM
P3
C11 C12
V
CC
V
EE
VCC
C15 C16
VEE
VEE C18 R27
VEE
VCC
P6
PD2
VEE
VEE
C10
P3
C9
VCC
16423-013
16423-014
16423-015
UG-1224 Amplifier Mezzanine Card User Guide
Rev. 0 | Page 12 of 14
8-LEAD MSOP AND SOIC DUAL AMC SCHEMATIC
Figure 46. 8-Lead MSOP and SOIC, Dual AMC Schematic
Figure 47. 8-Lead MSOP, Dual AMC Assembly Drawing, Primary Side
Figure 48. 8-Lead MSOP, Dual AMC Layout Pattern, Primary Side
8
4
5
7
6
8
4
3
1
2
C5
C6
R15 R17
VCM
VCM
R13
R22
R14
R18
R4
R19 VCC
C13 C14
VEE
C1
R9
R20
C2
R10
R1
R16
VINN
R2
R3 R21
VN
VP VS–
IC1:A
IC1:B
VO
VS+
VN
VP VS–
VO
VS+
R11 VOUTP PD1
P5
VEE VCC
C17 R26
R28
R29
VOUTN
VOUTP
PD-IN
P2
C7
R12 VOUTN
C8
R5
R7
C3
C4
VCM
R6
R8
VCM
VINP
P1 VINN
VINP
R25
R23 R24 VCM
P3
C11 C12
V
CC
V
EE
VCC
C15 C16
VEE
VEE C18 R27
VEE
VCC
P6
PD2
VEE
VEE
C10
P3
C9
VCC
16423-016
16423-017
16423-018
Amplifier Mezzanine Card User Guide UG-1224
Rev. 0 | Page 13 of 14
16-LEAD LFCSP FULLY DIFFERENTIAL AMC SCHEMATIC
Figure 49. 16-Lead LFCSP, Single AMC Schematic
Figure 50. 16-Lead LFCSP, Single AMC Assembly Drawing, Primary Side
Figure 51. 16-Lead LFCSP, Single AMC Layout Pattern, Primary Side
VCM
SUPPLIES
GND
NC
PD
NC
GND
VOUTN
VEE
VINP
GND
VINN
VCC GND
VOUTP
POWER DOW N
VOCM
TBD0402
DNI
R21
TBD0402
S
MA-J-P-H-ST-EM1
MTSW-107-07-T-S-240
69157-102HLF
DNI
69157-102HLF
DNI
DNI
DNI
TBD0402
TBD0402
DNIDNI
TBD0402
TBD0402
TBD0402
DNI
69157-102HLF
DNI
69157-102HLF
TSW-103-08-G-S
TBD0402
DNI
TBD0402
DNI
SMA-J-P-H-ST-EM1
DNI
SMA-J-P-H-ST-EM1
0.1UF
TBD0402
TBD0402
0.1UF
TBD0402
SMA-J-P-H-ST-EM1
MTSW-107-07-T-S-240
DNI
10UF
10UF
0.1UF
DNI
TBD0402
TBD0402
DNI DNI
DNI
DNI
DNI
R16
TBD0402
DNI
DNI
DNI
R17
TBD0402
DNI
DNI
TBD0402
DNI
DNI
TBD0402
DNI
TBD0402
DNI
TBD0402
DNI
TBD0402
DNI
TBD0402
DNI
DNI
TBD0402
TBD0805
TBD0402
DNI
TBD0402
TBD0402
DNI
TBD0402
69157-102HLF DNI
DNI
TBD0402
TBD0402
DNI 0.1UF
DNI
TBD0402
69157-102HLF
DNI
TBD0402
DNI
R15
TBD0402
TBD0805
DNI
DNI
DNI
TBD0402
DNI
TBD0402
ADA4945-1
DNI
DNI
TBD0402
TSW-103-08-G-S
DNI
69157-102HLF
DNI
DNI
69157-102HLF
P1
U1
R30
VCM
VOUTN
VOUTP
VINN
VINP C12
TBD0402
DNI
AGND
VEE
EXT_L
LOGIC
C13
EXT_H
VCC
MODE
P3
R25
R29
C6
C5
R14
R13
L2
C2
R4R3
J1
R1
R2
R27
R28
R6
R5
C1
C10
L1
R9
R10
R8
C4
C3
R24
R7 J2
C7
R23
C11C9
C8
PD
R26
TBD0402
DNI
R12
R11
R20 R19
R22
R18
PD
LOGIC
VEE
VEE
LOGIC
AGND
VCC
PD
LOGIC
VCC
AGND
VCC VOUTP
AGND
VEE
VOCM
VINN
VINP
VEE VEE
VCC VCC
AGND
VOUTN
VREF
VEE
VREF
VOCM
PD
VCCVCC
VCC
LOGIC
VEE
2
1
9
PAD
516
12
15
14
13
11
3
1
7
6
8
10
2
4
2
1
1
2345
2345
1
1
2345
2345
1
2
1
2
1
2
1
2
1
2
1
3
2
1
3
2
1
7
6
5
4
3
2
1
7
6
5
4
3
2
1
2
1
AGNDAGND
AGND AGND
AGND AGND
AGND
AGND
AGND
AGND
DISABLE_N
+FB
–FB
PAD
VOCM
–VCLAMP
LOGIC
–VS
–VS
+VCLAMP
+VS
+VS
MODE
–IN
+IN +OUT
–OUT
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
16423-111
16423-112
16423-113
UG-1224 Amplifier Mezzanine Card User Guide
Rev. 0 | Page 14 of 14
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly
return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred
damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications
to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer.
Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR
REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE
EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY
RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE
EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2019 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG16423-0-1/19(0)
