Series MB2000 Toggles Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): Logic/Power Level: (gold over silver) C Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Materials & Finishes Plunger: Frame: Movable Contactor: Movable Contacts: Stationary Contacts: Slides Rotaries Keylocks Contact Timing: Plunger Travel: Pretravel: Overtravel: Total Travel Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Tilt Tactiles 6A @ 125V AC & 3A @ 250V AC or 3A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Combines silver & gold ratings Note: Find additional explanation dual rating & operating range in Supplement section. Programmable Illuminated PB Pushbuttons General Specifications Rockers Miniature Pushbuttons Shock: Sealing: Touch Mounting Torque: Cap Installation Force: Soldering Time & Temp: Indicators Installation Process Seal: 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 50,000 operations minimum for splashproof models; 100,000 for all other models 25,000 operations minimum for silver; 50,000 operations minimum for gold 50,000 operations minimum for silver at 3A @ 125V AC Momentary Action: 1-pole 9.32N; 2-pole 16.18N; 4-pole 25.54N; Alternate Action: 1-pole 4.41N; 2-pole 7.06N; 4-pole 11.77N Slow make, slow break Screw-on Cap (Mom.) Screw-on Cap (Alt.) Snap-on Cap (Mom. & Alt.) .028" (0.71mm) .110" (2.80mm) .125" (3.19mm) .043" (1.09mm) .043" (1.10mm) .050" (1.26mm) .071" (1.80mm) .153" (3.90mm) .175" (4.45mm) Brass w/nickel plating; polyacetal w/B1 bushing Bushing: Brass with nickel plating Stainless steel Case: Diallyl phthalate resin (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Silver with silver plating (code W); copper or brass with gold plating (code G); or silver with gold plating (code A) Copper or brass with silver plating; copper or brass with gold plating -30C through +85C (-22F through +185F) 90 ~ 95% humidity for 96 hours @ 40C (104F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) B3 & D3 bushing options equivalent to IP67 1.5Nm (13.0 lb * in) for double nut; .7Nm (6.0 lb * in) for single nut 80.0N (18.0 lbf) maximum downward force on actuator Wave Soldering (PC version): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL: Supplement Accessories UL94V-0 case File No. E44145 - Recognized only when ordered with marking on switch. Add "/U" or "/CUL" before dash in part number to order UL recognized switch. All models recognized at 6A @ 125V AC or 3A @ 250V AC or 0.4VA max. @ 28V DC max. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add "/C" before dash in part number to order CSA certified switch. All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA max. @ 28V max. C72 www.nkkswitches.com 4/10/17 Series MB2000 Rockers Toggles Distinctive Characteristics Guide interlocked with actuator block prevents window locking and maintains correct plunger alignment to assure contact stability. Employs an over-center actuator mechanism, which diminishes sparking and increases operating life in AC circuits. C Programmable Illuminated PB High torque bushing construction prevents rotation or separation from frame during installation. Pushbuttons Miniature Pushbuttons Splashproof option (D3 and B3 bushing codes) features an o-ring within the bushing and one under the face nut to protect from splashed, sprayed, or spilled liquids. Keylocks High insulating barriers, formed in the molded diallyl phthalate case, increase isolation of circuits in multipole devices. Rotaries Prominent external insulating barriers increase insulation resistance and dielectric strength. Slides Epoxy sealed terminals prevent entry of solder flux and other contaminants. Bracket PC Mount Page C80 Large Bushing Page C87 Indicators Page C74 Accessories Bushing Mount www.nkkswitches.com Supplement Actual Size Touch Tilt Tactiles Clinching of the frame to the case well above the base and terminals provides 1,500V dielectric strength. C73 Toggles Series MB2000 TYPICAL SWITCH ORDERING EXAMPLE C S 2011 S1 Poles & Circuits Programmable Illuminated PB Pushbuttons Rockers MB 2011 SPDT ON (ON) 2065 SPDT ON ON 2061 DPDT ON (ON) 2085 DPDT ON ON 2181 4PDT ON (ON) 2185 4PDT ON ON 01 C Silver Rated 6A @ 125V AC & 3A @ 250V AC G Gold Rated 0.4VA max @ 28V AC/DC max A Gold over Silver Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max B .315" (8.0mm) Diameter C .394" (10.0mm) Diameter Cap Colors Plunger Types S Plunger for Screw-on Caps L Plunger for Snap-on Caps Bushings Tactiles IMPORTANT: Touch Tilt Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. A Black B White C Red E Yellow F Green G Blue H Gray S1 .335" (8.5mm) Threaded with Keyway S2 .335" (8.5mm) Smooth with Keyway S4 .335" (8.5mm) Metric Threaded with Keyway 01 Solder Lug .335" (8.5mm) Threaded with D-Flat 02 Quick Connect D1 03 .250" (6.35mm) Straight PC .335" (8.5mm) Threaded Splashproof without Keyway 05 .425" (10.8mm) Wirewrap D3 06 .750" (19.05mm) Wirewrap 07 .964" (24.5mm) Wirewrap 08 1.062" (27.0mm) Wirewrap Terminals DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators Black .394" (10.0mm) Diameter Cap Accessories MB2011SS1W01-CA SPDT ON-(ON) Circuit Plunger for Screw-on Caps .335" (8.5mm) Threaded Bushing with Keyway Supplement Silver Contacts with 6-Amp Rating Solder Lug Terminals C74 A Caps W ( ) = Momentary Keylocks W Contact Materials & Ratings Slides Rotaries Bushing Mount Miniature Pushbuttons www.nkkswitches.com Series MB2000 Toggles Bushing Mount Miniature Pushbuttons POLES & CIRCUITS Normal Keyway Down Note: Terminal numbers are not actually on the switch. Keyway MB2011 ON (ON) MB2065 ON ON MB2061 ON (ON) DP ON ON MB2181 ON (ON) MB2185 ON ON C 2 (COM) SP MB2085 Rockers Down 2-3 2-1 SPDT 2-3 5-6 2-1 5-4 DPDT 3 1 2 3 (COM) 1 Programmable Illuminated PB Model Throw & Switch Schematics 5 6 4 4PDT 2-3 5-6 8-9 11-12 4P 2-1 5-4 8-7 11-10 5 2 3 1 6 (COM) 4 11 8 9 7 12 Keylocks Normal Pole Connected Terminals 10 Rotaries PLUNGER TYPES Slides On alternate action models, after transferring circuit, the plunger returns to its original position and does not latch down. Plunger for Screw-on Caps (2.9) .114 (2.9) .114 (4.7) .185 (2.3) .091 (4.0) .157 Tilt (3.0) .118 Tactiles S Pushbuttons Plunger Position ( ) = Momentary Alternate Plunger Length Alternate Cap Location Indicators Plunger for Snap-on Caps (2.85) Dia .112 Accessories (10.4) .410 (3.6) .142 Momentary & Alternate Plunger Length Momentary & Alternate Cap Location www.nkkswitches.com Supplement L Momentary Cap Location Touch Momentary Plunger Length C75 Series MB2000 Toggles Bushing Mount Miniature Pushbuttons BUSHINGS Rockers S1 .335" (8.5mm) Threaded with Keyway C (0.8) .031 1/4-40 Thd (9.0) Dia .354 S4 (8.5) .335 (3.5) .138 (8.5) .335 (3.5) .138 D3 .335" (8.5mm) Threaded Splashproof without Keyway 1/4-40 Thd Keylocks 1/4-40 Thd (10.0) Dia .394 (2.5) .098 Rotaries (8.5) .335 (8.5) .335 (3.5) .138 (3.5) .138 Maximum Panel Thickness with Standard Hardware: .240" (6.1mm) Maximum Panel Thickness with Standard Hardware: .154" (3.9mm) Panel Cutouts For S1, S2, or S4 Bushing with Keyway Tactiles Slides (2.5) .098 For S1 or S4 Bushing with Optional Locking Ring (5.6) or .228 (6.5) Dia .256 (2.2) Dia .087 (6.5) Dia .256 (5.8) .228 For D3 Bushing without Keyway (6.5) Dia .256 Standard hardware for bushings S1, S4, & D1 includes 2 hex nuts & 1 lockwasher; D3 bushing has 1 hex nut & 1 o-ring. Standard & optional hardware are illustrated following the Typical Switch Dimension drawings. CONTACT MATERIALS & RATINGS W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Note: Complete explanation of operating range in Supplement section. Accessories Indicators Tilt (0.6) .024 (6.5) or .240 For D1 Bushing with D Flat Touch (6.5) Dia .256 A Gold over Silver Power Level or Logic Level 6A @ 125V AC & 3A @ 250V AC or 0.4VA maximum @ 28V AC/DC maximum Supplement Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section for complete explanation of dual rating and operating range. C76 (3.5) .138 Maximum Panel Thickness with Standard Hardware: .154" (3.9mm) .335" (8.5mm) Threaded with D Flat (9.0) Dia .354 M6P0.75 (9.0) Dia .354 (2.5) .098 Maximum Panel Thickness with Standard Hardware: .154" (3.9mm) D1 .335" (8.5mm) Metric Threaded with Keyway (0.8) .031 (6.2) Dia .244 (9.0) Dia .354 (2.5) .098 (8.5) .335 Programmable Illuminated PB Pushbuttons (0.8) .031 .335" (8.5mm) Smooth with Keyway S2 www.nkkswitches.com Series MB2000 Toggles Bushing Mount Miniature Pushbuttons TERMINALS (6.35) .250 Epoxy Seal (2.0) .079 (2.0) (1.1) .079 .043 Thk = (0.8) .031 (1.57) .062 Thk = (0.8) .031 (4.8) .189 3 2 (4.7) Typ .185 1 6 2 5 1 4 (1.8) Dia Typ .073 07 .964" (24.5mm) Wirewrap or Extended PC 08 1.062" (27.0mm) Wirewrap or Extended PC 5 8 11 1 4 7 10 (4.7) Typ .185 (1.8) Dia Typ .073 Double Pole Four Pole Keylocks .750" (19.05mm) Wirewrap or Extended PC 2 (4.8) Typ .189 If using as extended PC terminal, refer to the above footprints. Epoxy Seal A Dimension A = terminal lengths as shown beside the terminal codes at the left. (1.27) .050 Thk = (0.8) .031 CAPS & CAP COLORS AT443 .315" (8.0mm) Diameter Snap-on Cap C AT407 .394" (10.0mm) Diameter Screw-on Cap For use with Plunger Code S For use with Plunger Code L Cap Material: PBT Finish: Glossy Cap Material: Polycarbonate Cap Material: PBT Finish: Glossy Finish: Glossy Cap Colors Available: A (10.0) Dia .394 (8.0) Dia .315 M2.3 P0.4 Black B White C For use with Plunger Code L Cap Material: Polycarbonate Finish: Glossy (8.0) .315 (8.0) .315 (7.6) .299 (6.5) .256 (8.0) Dia .315 For use with Plunger Code S AT442 .394" (10.0mm) Diameter Snap-on Cap Red E Yellow www.nkkswitches.com (10.0) Dia .394 M2.3 P0.4 F Green Accessories AT413 .315" (8.0mm) Diameter Screw-on Cap G Blue H Supplement B Rotaries 06 12 Slides .425" (10.8mm) Wirewrap or Extended PC 9 (1.8) Dia Typ .073 Single Pole 05 6 Tactiles (1.17) .046 Thk = (0.8) .031 (4.7) Typ .185 3 Tilt (6.35) (4.8) .250 .189 Epoxy Seal 3 Programmable Illuminated PB .250" (6.35mm) Straight PC C Touch 03 Rockers (4.0) .157 Epoxy Seal .062" (1.57mm) Wide Quick Connect Pushbuttons 02 Solder Lug Indicators 01 Gray C77 Toggles Series MB2000 Bushing Mount Miniature Pushbuttons TYPICAL SWITCH DIMENSIONS Single Pole Rockers Solder Lug (1.1) x (2.0) Typ .043 x .079 Keylocks Programmable Illuminated PB Pushbuttons 1/4-40 Thd (0.8) Typ .031 Keyway C 3 (4.7) Typ .185 (10.0) Dia .394 (13.0) .512 2 COM 1 (2.3) .091 (7.9) .311 (8.0) .315 (0.5) .020 (3.5) .138 (8.5) .335 (4.5) .177 (21.0) .827 (2.0) .079 MB2011SS1W01-CA Solder Lug Double Pole Rotaries 1/4-40 Thd (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 Keyway (4.7) Typ .185 (10.0) Dia .394 Slides (12.7) .500 (8.5) .335 5 2 4 1 (13.0) .512 (2.0) Typ .079 (4.5) .177 (4.8) .189 (21.0) .827 Tactiles (8.0) .315 3 (0.5) .020 (3.5) .138 (2.3) .091 COM 6 Solder Lug Four Pole Touch Tilt MB2061SS1W01-CA 1/4-40 Thd (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 Keyway Indicators Accessories Supplement (4.7) Typ .185 (10.0) Dia .394 (22.3) .878 (2.3) .091 (3.5) .138 (8.0) .315 (8.5) .335 MB2181SS1W01-CA C78 www.nkkswitches.com (4.5) .177 (21.0) .827 (0.5) .020 COM 12 9 6 3 11 8 5 2 10 7 4 1 (13.0) .512 (2.0) Typ .079 (4.8) Typ .189 Series MB2000 Toggles Bushing Mount Miniature Pushbuttons HARDWARE AT513H for Inch AT513M for Metric Hexagon Nut AT509 Lockwasher AT516 O-ring for Splashproof Bushing AT507H for Inch AT507M for Metric Locking Ring 2 included with each switch (1 with splashproof models) 1 included with each switch (not with splashproof models) 1 included with each splashproof model Material: Steel with Zinc/Chromate Material: Brass with Nickel plating Material: Steel with Zinc/Chromate Material: Nitrile butadiene rubber (6.0) Dia or .250 1/4-40 Thd or M6 P0.75 (6.07) Dia (9.63) Dia .239 .379 (6.4) Dia (10.2) Dia .252 .402 (12.0) Dia .472 (2.0) .079 (5.5) or .229 (0.5) .020 (1.7) .067 (1.78) .070 Optional Mounting Collars/Conical Nuts (0.8) .031 Keylocks (1.5) .059 Optional Splashproof Boots for S Plunger AT512CH for Inch AT512CM for Metric Conical nut AT4041H for Inch AT4041M for Metric Boot for Momentary AT4042H for Inch AT4042M for Metric Boot for Alternate Used with .315" (8.0mm) Diameter Cap (cap code B) Material: Brass with chrome plating Used with .394" (10.0mm) Diameter Cap (cap code C) Material: Brass with chrome plating Material: Silicone rubber Material: Silicone rubber Tactiles Slides AT512H for Inch AT512M for Metric Conical Nut Rotaries (9.0) .354 M6 P0.75 or 1/4-40 Thd (10.0) .394 (4.0) Max .157 (10.0) .394 (10.0) .394 (4.0) Max .157 (3.5) Min .138 Dimension A = Cap Height Operating Life 100,000 .091" (2.3mm) for Momentary with Plunger Code S .157" (4.0mm) for Alternate with Plunger Code S .142" (3.6mm) for Momentary & Alternate with Plunger Code L Boots for momentary devices are accompanied by a threaded adaptor which extends the length of the plunger. Optional Conical Nuts fit with all 8.5mm bushing options except the D3 & S2 bushings. www.nkkswitches.com Tilt (8.5) .335 (8.5) .335 (4.0) Max .157 Touch (4.9) Dia .193 (6.0) Dia .236 (4.9) Dia .193 (6.0) Dia .236 (10.0) .394 (8.5) .335 (10.8) .425 (10.8) .425 (10.0) .394 (4.0) Max .157 (3.5) Min .138 Operating Life 30,000 Accessories A M2.3 P0.4 (14.0) Dia .551 (12.2) Dia .480 Supplement A (13.0) Dia .512 (10.5) Dia .413 Indicators (8.0) .315 C Pushbuttons Rockers Optional Hardware Programmable Illuminated PB Standard Hardware C79 Toggles Series MB2000 TYPICAL SWITCH ORDERING EXAMPLE C S 2011 S2 Poles & Circuits 2011 Programmable Illuminated PB Pushbuttons Rockers MB SPDT ON (ON) 2065 SPDT ON ON 2061 DPDT ON (ON) 2085 DPDT ON ON 2181 4PDT ON (ON) 2185 4PDT ON ON ( ) = Momentary Keylocks G Gold Rated 0.4VA max @ 28V AC/DC max Tactiles C .394" (10.0mm) Diameter Gold over Silver Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max S2 S1 .335" (8.5mm) Threaded with Keyway A2 .200" (5.08mm) Smooth with Keyway Only Available in Part Numbers MB2011SA2G31 & MB2011SA2W31 Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. Tilt .315" (8.0mm) Diameter Cap Colors .335" (8.5mm) Smooth with Keyway IMPORTANT: A Black B White C Red E Yellow F Green G Blue H Gray Terminals 13 .250" (6.35mm) Straight PC with Bracket 40 .150" (3.81mm) Vertical PC 45 .100" (2.54mm) Vertical PC 30 Right Angle PC with .646" (16.4mm) Support to Terminals Available in 1- & 2-pole only 31 Right Angle PC with .500" (12.7mm) Support to Terminals Available in 1-pole only DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators MB2011SS2G13-CA Black .394" (10.0mm) Diameter Cap Accessories .335" (8.5mm) Smooth Bushing with Keyway Supplement Gold Contacts with 0.4VA Rating Plunger for Screw-on Caps SPDT ON-(ON) Circuit .250" (6.35mm) Straight PC Terminals with Bracket C80 www.nkkswitches.com A B Bushings Plunger for Screw-on Caps C Caps W Plunger Type Touch 13 Silver Rated 6A @ 125V AC & 3A @ 250V AC A 4-pole not for use with right angle terminals S G Contact Materials & Ratings Slides Rotaries Bracket PC Mount Miniature Pushbuttons Series MB2000 Toggles Bracket PC Mount Miniature Pushbuttons POLES & CIRCUITS 4P MB2011 ON (ON) MB2065 ON ON MB2061 ON (ON) MB2085 ON ON MB2181 ON (ON) MB2185 ON ON 2-3 2-1 3 2-3 5-6 2-1 5-4 2-3 5-6 8-9 11-12 2-1 5-4 8-7 11-10 Rockers C 2 (COM) SPDT 1 2 DPDT (COM) 3 1 5 6 4 4PDT 5 2 3 1 6 (COM) 9 4 11 8 7 12 10 PLUNGER TYPE Plunger for Screw-on Caps (3.0) .118 (4.7) .185 (2.3) .091 Momentary Plunger Length Momentary Cap Location Slides (2.9) .114 (2.9) .114 (4.0) .157 Alternate Plunger Length Alternate Cap Location Tactiles S Rotaries On alternate action models, after transferring circuit, the plunger returns to its original position and does not latch down. BUSHINGS (0.8) .031 (9.0) Dia .354 (6.2) Dia .244 .335" (8.5mm) Threaded with Keyway (0.8) .031 (9.0) Dia .354 (2.5) .098 (8.5) .335 A2 (9.0) Dia .354 (2.5) .098 (8.5) .335 (6.2) Dia .244 (0.8) .031 1/4-40 Thd (3.5) .138 .200" (5.08mm) Smooth with Keyway (3.5) .138 Standard hardware: 2 hex nuts (AT513H) & 1 lockwasher (AT509) Optional hardware: Locking ring (AT507) Tilt S1 (2.5) .098 Touch .335" (8.5mm) Smooth with Keyway S2 (5.08) .200 (3.0) .118 Only available in part numbers MB2011SA2W31 & MB2011SA2G31 Panel Cutouts For S2, S1, or A2 Bushing with Keyway (6.5) Dia .256 (5.8) .228 (0.6) .024 With Optional Locking Ring (6.5) Dia .256 (2.2) Dia .087 www.nkkswitches.com (6.1) .240 Maximum Panel Thickness with Standard Hardware: .154" (3.9mm) C81 Indicators DP Note: Terminal numbers are not actually on the switch. Keyway Accessories SP Keyway Down Keylocks Model Normal Supplement Pole Down Throw & Switch Schematics Pushbuttons Normal Connected Terminals Programmable Illuminated PB Plunger Position ( ) = Momentary Toggles Series MB2000 Rockers CONTACT MATERIALS & RATINGS W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Note: Complete explanation of operating range in Supplement section. C A Programmable Illuminated PB Pushbuttons Bracket PC Mount Miniature Pushbuttons Power Level or Logic Level Gold over Silver 6A @ 125V AC & 3A @ 250V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section for complete explanation of dual rating and operating range. TERMINALS .250" (6.35mm) Straight PC with Bracket Keylocks 13 40 45 .150" (3.81mm) Vertical PC .100" (2.54mm) Vertical PC (6.35) .250 (2.54) .100 Rotaries (3.81) .150 Right Angle PC with .646" (16.4mm) Support to Terminal Right Angle PC with .500" (12.7mm) Support to Terminal 31 Tactiles Slides 30 (12.7) .500 Tilt (16.4) .646 Only Available in 1 & 2 Pole Touch Note: Full dimensioned drawings appear on the following pages. Supplement Accessories Indicators CAPS & CAP COLORS B AT413 .315" (8.0mm) Diameter Screw-on Cap C (6.5) .256 Cap Material: PBT Finish: Glossy Cap Colors Available: C82 A (8.0) Dia .315 Black B White Cap Material: PBT Finish: Glossy M2.3 P0.4 C AT407 .394" (10.0mm) Diameter Screw-on Cap Red E www.nkkswitches.com Yellow F (8.0) .315 (10.0) Dia .394 Green G Blue M2.3 P0.4 H Gray Series MB2000 Toggles Bracket PC Mount Miniature Pushbuttons TYPICAL SWITCH DIMENSIONS (13.0) .512 2 COM (1.8) Dia Typ .073 (1.5) Dia Typ .059 (1.17) Typ .046 (3.2) .126 (7.9) .311 (22.9) .902 (8.5) .335 C (4.7) Typ .185 1 (6.35) .250 (2.3) .091 (7.9) Typ .311 2 1 (0.5) Typ .020 (3.0) .118 (8.0) .315 (15.8) .622 MB2011SS2G13-CA (0.8) Typ .031 (4.7) Typ .185 (2.3) .091 (8.0) .315 6 (15.8) .622 COM 3 5 2 4 1 (13.0) .512 (0.5) Typ .020 (3.0) .118 3 6 2 5 1 4 (1.17) Typ .046 (4.8) .189 (6.35) .250 CL (7.9) Typ .311 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 (12.7) .500 (22.9) .902 (8.5) .335 (1.6) Typ .063 (2.4) Typ .095 (1.17) Typ .046 Rotaries (6.2) Dia .244 (10.0) Dia .394 (9.0) .354 (3.2) .126 (4.5) .177 Slides Keyway Straight PC with Bracket Keylocks Double Pole MB2061SS2G13-CA Four Pole Pushbuttons (4.7) Typ .185 (1.6) Typ .063 3 3 Programmable Illuminated PB (0.8) Typ .031 (10.0) Dia .394 (9.0) .354 (1.17) Typ .046 (4.5) .177 (6.2) Dia .244 Tactiles Keyway Straight PC with Bracket Rockers Single Pole Straight PC with Bracket Tilt (3.2) .126 (1.17) Typ .046 (4.7) Typ .185 (2.3) .091 (8.0) .315 (8.5) .335 10 8 5 2 7 4 1 (13.0) .512 Touch 11 (1.17) Typ .046 (4.8) Typ .189 (15.8) .622 (22.3) .878 (0.5) Typ .020 (3.0) .118 3 (1.6) Typ .063 (6.35) .250 (22.9) .902 3 6 9 12 2 5 8 11 1 4 7 10 CL www.nkkswitches.com Indicators (0.8) Typ .031 (10.0) Dia .394 (9.0) .354 COM 6 (4.8) Typ .189 Accessories (4.5) .177 (6.2) Dia .244 9 (7.9) Typ .311 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 Supplement Keyway 12 MB2181SS2G13-CA C83 Toggles Series MB2000 Bracket PC Mount Miniature Pushbuttons TYPICAL SWITCH DIMENSIONS Single Pole Rockers .150" (3.81mm) Vertical PC Keyway (6.2) Dia .244 3 (10.0) Dia .394 C 2 (2.3) .091 (10.3) .406 (11.75) .463 (0.5) (0.8) Typ .020 .031 (3.25) .128 (16.4) .646 (3.81) Typ .150 1 (1.27) .050 (3.81) Typ .150 (1.8) Dia Typ .073 (2.54) Typ .100 (7.9) .311 MB2011SS2G40-CA .150" (3.81mm) Vertical PC Double Pole COM Rotaries (2.3) .091 (10.3) .406 3 5 2 4 1 (11.75) .463 (0.5) (0.8) Typ .020 .031 (3.25) .128 (16.4) .646 3 6 2 5 1 4 (16.4) .646 Four Pole Touch 12 9 6 3 11 8 5 2 10 7 4 1 (22.3) .878 (10.0) Dia .394 (2.3) .091 (2.7) .106 (1.4) Typ .055 (5.08) .200 (13.0) .512 (1.27) Typ .050 (4.8) Typ .189 (6.2) Dia .244 Keyway Indicators (3.81) Typ .150 (1.8) Dia Typ .073 (2.54) Typ .100 .150" (3.81mm) Vertical PC Accessories (4.8) .189 (3.81) Typ .150 MB2061SS2G40-CA (8.0) .315 (11.75) .463 (0.5) (0.8) Typ .020 .031 (3.25) .128 (16.4) .646 (3.81) Typ .150 3 6 9 2 5 8 11 1 4 7 10 12 (4.8) Typ .189 (3.81) Typ .150 (16.4) .646 (1.8) Dia Typ .073 (2.54) Typ .100 MB2181SS2G40-CA C84 (13.0) .512 (4.8) .189 (12.7) .500 (10.0) Dia .394 (2.7) .106 (1.4) Typ .055 (5.08) .200 6 (1.27) Typ .050 (6.2) Dia .244 Keyway COM Supplement 2 (13.0) .512 (16.4) .646 (2.7) .106 (1.4) Typ .055 (5.08) .200 Slides Tactiles Tilt COM 1 Keylocks Programmable Illuminated PB Pushbuttons 3 www.nkkswitches.com Series MB2000 Toggles Bracket PC Mount Miniature Pushbuttons TYPICAL SWITCH DIMENSIONS .100" (2.54mm) Vertical PC Rockers Single Pole (6.2) Dia .244 (10.0) Dia .394 (13.0) .512 2 COM 1 C 1 (16.4) .646 (2.3) .091 (2.7) .106 (1.4) Typ .055 (5.08) .200 (10.3) .406 (11.75) .463 (0.5) (0.8) Typ .020 .031 (3.25) .128 (16.4) .646 (1.27) .050 (2.54) Typ .100 (1.8) Dia Typ .073 (2.54) Typ .100 (7.9) .311 MB2011SS2G45-CA .100" (2.54mm) Vertical PC (4.8) .189 (10.0) Dia .394 COM 6 3 5 2 4 1 (13.0) .512 3 6 2 5 1 4 (2.54) Typ .100 Rotaries (6.2) Dia .244 Keyway Keylocks Double Pole (16.4) .646 (10.3) .406 (11.75) .463 (0.5) (0.8) Typ .020 .031 (3.25) .128 (16.4) .646 (1.27) Typ .050 (2.54) Typ .100 (4.8) .189 (12.7) .500 (1.8) Dia Typ .073 (2.54) Typ .100 Slides (2.3) .091 (2.7) .106 (1.4) Typ .055 (5.08) .200 MB2061SS2G45-CA COM .100" (2.54mm) Vertical PC 12 9 6 3 11 8 5 2 10 7 4 1 (6.2) Dia .244 (2.54) Typ .100 6 9 2 5 8 (4.8) Typ .189 (2.54) Typ .100 11 1 4 7 10 Touch 12 Accessories (11.75) .463 3 (16.4) .646 (1.8) Dia Typ .073 (2.54) Typ .100 www.nkkswitches.com Supplement (10.3) .406 (0.5) (0.8) Typ .020 .031 (3.25) .128 (16.4) .646 Indicators (22.3) .878 (2.3) .091 (1.4) Typ .055 (5.08) .200 (13.0) .512 (1.27) Typ .050 (4.8) Typ .189 (10.0) Dia .394 (2.7) .106 Tilt Four Pole Keyway Programmable Illuminated PB 2 Pushbuttons (2.54) .100 3 3 Tactiles Keyway MB2181SS2G45-CA C85 Toggles Series MB2000 Bracket PC Mount Miniature Pushbuttons TYPICAL SWITCH DIMENSIONS Single Pole Keylocks (10.0) Dia .394 Keyway (6.2) Dia .244 (4.7) Typ .185 COM 1 2 3 (4.0) .157 C 2 3 (7.9) .311 1 (4.3) .169 (2.9) .114 (1.4) Typ .055 (5.08) .200 Programmable Illuminated PB Pushbuttons Rockers Right Angle PC (2.3) .091 (8.0) .315 (11.75) .463 (0.5) .020 (3.25) (1.27) .050 .128 (16.4) .646 (16.4) .646 (0.8) Typ .031 (4.7) Typ .185 (2.95) .116 (1.8) Dia Typ .073 (2.54) Typ .100 (13.0) .512 MB2011SS2G30-CA Right Angle PC Double Pole (10.0) Dia (6.2) Dia .394 .244 (4.7) Typ .185 COM Rotaries Keyway 4 5 6 1 2 3 Slides (6.4) .252 (12.7) .500 6 5 4 3 2 1 (4.3) .169 (2.3) .091 (8.0) .315 (11.75) .463 (0.5) (1.27) Typ .020 .050 (3.25) (3.81) .150 .128 (16.4) .646 (2.95) .116 (16.4) .646 (0.8) Typ .031 (4.7) Typ .185 (1.8) Dia Typ .073 (2.54) Typ .100 (13.0) .512 Tactiles (2.9) .114 (1.4) Typ .055 (5.08) .200 (3.81) .150 Right Angle PC with .500" (12.7mm) Support to Terminal Touch Tilt MB2061SS2G30-CA Keyway Single Pole (10.0) Dia .394 (6.2) Dia .244 COM 1 2 Indicators (4.5) .177 Supplement Accessories (2.9) .114 (1.4) Typ .055 (5.08) .200 (7.9) .311 (4.3) .169 (2.3) .091 (8.0) .315 (6.9) .272 (12.0) .472 MB2011SA2G31-CA C86 3 www.nkkswitches.com (0.5) .020 (1.27) .050 (12.7) .500 (0.8) Typ .031 (4.7) Typ .185 (3.4) .134 (13.0) .512 3 2 (4.7) Typ .185 1 (12.7) .500 (1.8) Dia Typ .073 (2.54) Typ .100 Toggles Series MB2000 TYPICAL SWITCH ORDERING EXAMPLE B1 Poles & Circuits (ON) 2065 SPDT ON ON 2061 DPDT ON (ON) 2085 DPDT ON ON 2181 4PDT ON (ON) 2185 4PDT ON ON C Caps W Silver Rated 6A @ 125V AC & 3A @ 250V AC G Gold Rated 0.4VA max @ 28V AC/DC max B .315" (8.0mm) Diameter C .394" (10.0mm) Diameter D .520" (13.2mm) Diameter E .748" (19.0mm) Diameter ( ) = Momentary B1 .472" (12.0mm) Threaded with Keyway B3 .472" (12.0mm) Threaded w/Splashproof 02 Quick Connect 03 .250" (6.35mm) Straight PC 05 .425" (10.8mm) Wirewrap 06 .750" (19.05mm) Wirewrap 07 .964" (24.5mm) Wirewrap 08 1.062" (27.0mm) Wirewrap B White C Red *D Amber *E Yellow F Green *G Blue *H Gray Rotaries Bushings Solder Lug Black * Not available with cap code E Tactiles Plunger Type Plunger for Screw-on Caps 01 A Keylocks Cap Colors Terminals IMPORTANT: Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. Touch DESCRIPTION FOR TYPICAL ORDERING EXAMPLE MB2011SB1W01-DA Black .520" (13.2mm) Diameter Cap Plunger for Screw-on Caps .472" (12.0mm) Diameter Threaded Bushing with Keyway Silver Contacts with 6-Amp Rating SPDT ON-(ON) Circuit Supplement S A Slides ON Contact Materials & Ratings D Tilt SPDT 01 Indicators 2011 W Rockers S Programmable Illuminated PB 2011 Accessories MB Pushbuttons Large Bushing Miniature Pushbuttons Solder Lug Terminals www.nkkswitches.com C87 Series MB2000 Toggles Large Bushing Miniature Pushbuttons POLES & CIRCUITS Normal Pole C SP DP 4P Model Connected Terminals Down Normal Keyway Throw & Switch Schematics Down Note: Terminal numbers are not actually on the switch. Keyway MB2011 ON (ON) MB2065 ON ON MB2061 ON (ON) MB2085 ON ON MB2181 ON (ON) MB2185 ON ON 2 (COM) 2-3 2-1 SPDT 2-3 5-6 2-1 5-4 DPDT 2-3 5-6 8-9 11-12 2-1 5-4 8-7 11-10 3 2 1 (COM) 3 4PDT 1 5 2 3 1 6 5 6 (COM) 4 4 11 8 9 7 12 10 PLUNGER TYPE Keylocks Programmable Illuminated PB Pushbuttons Rockers Plunger Position ( ) = Momentary Rotaries S (6.7) Dia .264 (6.4) Dia .252 Plunger for Screw-on Caps Plunger is plastic for B1 bushing. (5.3) .208 On alternate action models, after transferring circuit, the plunger returns to its original position, and does not latch down. (5.3) .208 Plunger is metal for B3 bushing. Slides BUSHINGS B1 .472" (12.0mm) Diameter Threaded with Keyway .472" (12.0mm) Diameter Threaded Splashproof B3 Maximum Panel Thickness with Standard Hardware: .217" (5.5mm) (1.85) .073 Maximum Panel Thickness with Standard Hardware: .217" (5.5mm) M12P1 (1.1) .043 (5.0) .197 (12.0) .472 Tilt Tactiles M12P1 (2.0) .079 (4.9) .193 (18.0) Dia .709 (12.0) .472 Panel Cutouts For B1 Bushing with Keyway Accessories Supplement For B1 Bushing with Locking Ring (11.5) .453 (1.5) .060 Indicators Touch (12.5) Dia .492 (12.5) Dia .492 For B3 Bushing without Keyway (9.0) .354 (12.5) Dia .492 (3.0) Dia .118 CONTACT MATERIALS & RATINGS W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Note: Complete explanation of operating range in Supplement section. C88 www.nkkswitches.com Series MB2000 Toggles Large Bushing Miniature Pushbuttons TERMINALS (2.0) (1.1) .079 .043 Thk = (0.8) .031 (1.57) .062 Thk = (0.8) .031 (4.8) .189 3 1 (1.8) Dia Typ .073 (1.17) .046 Thk = (0.8) .031 .425" (10.8mm) Wirewrap or Extended PC 06 .750" (19.05mm) Wirewrap or Extended PC 07 .964" (24.5mm) Wirewrap or Extended PC 08 1.062" (27.0mm) Wirewrap or Extended PC 5 1 4 (4.7) Typ .185 3 6 9 12 2 5 8 11 1 4 7 10 Double Pole Epoxy Seal (4.7) Typ .185 (1.8) Dia Typ .073 (1.8) Dia Typ .073 Single Pole 05 6 2 Four Pole If using as extended PC terminal, refer to the above footprints. A Rotaries (6.35) (4.8) .250 .189 Epoxy Seal 3 Dimension A = terminal lengths as shown beside the terminal codes at the left. (1.27) .050 Thk = (0.8) .031 Slides 2 (4.7) Typ .185 C (4.8) Typ .189 Programmable Illuminated PB .250" (6.35mm) Straight PC 03 CAPS & CAP COLORS D AT414 .520" (13.2mm) Diameter Screw-on Cap AT412 .748" (19.0mm) Diameter Screw-on Cap E Tilt AT079 .394" (10.0mm) Diameter Screw-on Cap C Material: Polystyrene Finish: Glossy Material: Polystyrene Finish: Glossy Material: PBT Finish: Glossy Material: Polystyrene Finish: Glossy Colors Available: ABCEFGH Colors Available: ABCEFGH Colors Available: ABCDEFGH Colors Available: ABCF Cap Color Codes: A Black (8.0) .315 (13.28) .523 B White C Red (11.0) .433 (15.0) .590 D Amber E (19.0) Dia .748 Yellow www.nkkswitches.com F (8.0) .315 (12.0) .472 Green G Accessories (6.5) .256 (11.79) .464 (13.2) Dia .520 (10.0) Dia .394 (8.0) Dia .315 Touch AT078 .315" (8.0mm) Diameter Screw-on Cap Indicators B Pushbuttons (2.0) .079 Rockers (6.35) .250 Epoxy Seal Keylocks .062" (1.57mm) Wide Quick Connect 02 (4.0) .157 Epoxy Seal Tactiles Solder Lug Blue H Gray C89 Supplement 01 Toggles Series MB2000 Large Bushing Miniature Pushbuttons TYPICAL SWITCH DIMENSIONS Single Pole Rockers Solder Lug Keylocks Programmable Illuminated PB Pushbuttons Keyway M12P1 (1.1) x (2.0) Dia Typ .043 x .079 (0.8) Typ .031 3 C (13.2) Dia .520 (4.7) Typ .185 (4.0) .157 (15.0) .590 (12.0) .472 1 (0.5) .020 (13.0) .512 (7.9) .311 (13.0) .512 2 COM (4.5) .177 (17.5) .689 (2.0) .079 MB2011SB1W01-DA Solder Lug Double Pole Rotaries Keyway M12P1 (1.1) x (2.0) Dia Typ .043 x .079 (13.2) Dia .520 COM (4.7) Typ .185 Slides (4.0) .157 (15.0) .590 3 5 2 4 1 (13.0) .512 (2.0) Typ .079 (4.5) .177 (4.8) .189 (17.5) .689 Tactiles (12.0) .472 6 (0.5) .020 (13.0) .512 (12.7) .500 (0.8) Typ .031 Solder Lug Four Pole Touch Tilt MB2061SB1W01-DA Keyway (1.1) x (2.0) Dia Typ .043 x .079 Indicators (13.2) Dia .520 COM (15.0) .590 MB2181SB1W01-DA C90 www.nkkswitches.com (12.0) .472 12 9 6 3 11 8 5 2 10 7 4 1 (13.0) .512 (0.5) .020 (13.0) .512 (22.3) .878 (0.8) Typ .031 (4.7) Typ .185 (4.0) .157 Accessories Supplement M12P1 (17.5) .689 (2.0) Typ .079 (4.5) .177 (4.8) Typ .189 Series MB2000 Toggles Large Bushing Miniature Pushbuttons HARDWARE AT503M Hex Face Nut AT508 Lockwasher AT527M Hex Nut AT506M Locking Ring Material: Brass with Chrome plating Material: Steel with Zinc/Chromate Material: Steel with Nickel plating Material: Steel with Zinc/Chromate (15.8) Dia .622 (14.0) .551 (18.2) Dia .717 (2.8) .110 (13.8) Dia .543 (16.0) .630 (2.4) .094 (11.5) .453 (0.5) .020 (1.0) .039 (16.0) .630 (2.0) .079 (2.8) .110 (9.5) .374 (1.0) .039 Keylocks (14.3) .563 (12.1) Dia .476 M12 P1 Programmable Illuminated PB (12.1) .476 M12 P1 C Pushbuttons Rockers Standard Hardware for B1 Bushing AT401P O-ring Material: Nitrile butadiene rubber (14.3) .563 (16.0) .630 (2.4) .094 (12.1) Dia .476 (17.5) Dia .689 Slides Material: Brass with Chrome plating Tactiles M12 P1 (1.5) .059 Tilt AT503M Hex Face Nut Rotaries Standard Hardware for B3 Bushing AT4043 Splashproof Boot (4.0) Max .157 (3.5) Min .138 Supplement (9.0) .354 M12 P1 Accessories (10.7) .421 Indicators (18.0) Dia .709 (12.6) Dia .496 (9.6) Dia .378 Material: Silicone Rubber Operating Life: 10,000 for momentary 30,000 for alternate action When using a splashproof boot, no cap is required. Touch Optional Splashproof Boot for B1 Bushing www.nkkswitches.com C91 Toggles Series MB2000 CUSTOM ASSEMBLY ORDERING EXAMPLE Rockers The MB2000 pushbutton series offers flexibility to accommodate a variety of applications. Using a basic large bushing model, different accessories can be assembled onto the switch to achieve the mounting variations shown on the following two pages. These switches have: C * * * * 12mm diameter threaded bushing with keyway Silver contacts 6-Amp rating Solder lug terminals Other 12mm bushing options can be used; see details in preceding Large Bushing Ordering tables. Programmable Illuminated PB Pushbuttons Large Bushing Miniature Pushbuttons SB1W01 MB2011 Mounter Shapes For Shroud C A Cap Colors For Shroud Mounter Colors For Shroud 2011 SPDT ON (ON) 2065 SPDT ON ON 4 Round A Black A Black 2061 DPDT ON (ON) 5 Rectangular B White B White 2085 DPDT ON ON C Red H Gray 4-pole available F Green ( ) = Momentary G Blue H Gray Slides Rotaries Keylocks Poles & Circuits 4 A Black B White C Red F Green Indicators Touch Tilt Tactiles Cap Colors For Snap-In Round Shroud See custom assemblies on following pages. Accessories MB2011SB1W01-4C-A Supplement Rectangular Shroud MB2011SB1W01-5C-A C92 www.nkkswitches.com Toggles Series MB2000 MOUNTER SHAPES FOR SHROUDS Rockers AT453 Rectangular Material: Polycarbonate Material: Polycarbonate Colors: A B H Colors: A B H C Programmable Illuminated PB 5 AT455 Round AT452 Rectangular Insert Cap Material: Polycarbonate Material: Polycarbonate Colors: A B C F G H Colors: A B C F G H Rotaries AT454 Round Insert Cap Keylocks CAPS & CAP COLORS FOR SHROUDS Slides AT080 Screw Adaptor for Insert Caps Tactiles Material: Brass Tilt Color Codes: White C Red F Green G Blue H Gray Touch B Indicators Black Accessories A Supplement 4 Pushbuttons Large Bushing Miniature Pushbuttons www.nkkswitches.com C93 Toggles Series MB2000 Large Bushing Miniature Pushbuttons CUSTOM ASSEMBLY WITH ROUND SHROUD (1.1) x (2.0) Typ .043 x .079 Keyway Rockers M12P1 (0.8) Typ .031 Programmable Illuminated PB Pushbuttons (17.7) Dia .697 (4.7) Typ .185 C (18.4) Dia .724 (22.0) Dia .866 (24.0) Dia .945 (0.5) .020 (4.5) .177 (13.0) .512 (27.5) 1.083 (2.0) .079 (14.0) .551 MB2011SB1W01-4C-A Single Pole Double Pole (12.5) Dia .492 3 Keylocks COM 2 (13.0) .512 COM 1 6 3 5 2 4 1 (11.5) .453 (13.0) .512 (1.5) .060 Rotaries (2.0) Typ .079 Effective Panel Thickness: .217" (5.5mm) maximum (4.8) .189 (2.0) .079 (7.9) .311 (12.7) .500 Slides CUSTOM ASSEMBLY WITH RECTANGULAR SHROUD (1.1) x (2.0) Typ .043 x .079 Keyway Tactiles M12P1 (20.1) .791 (26.2) 1.031 (19.4) .764 (4.7) Typ .185 Tilt (24.6) .969 (0.8) Typ .031 Touch (16.1) .634 (20.6) .811 (2.0) .079 Indicators Single Pole Double Pole 3 Accessories COM (14.0) .551 (21.0) .827 MB2011SB1W01-5C-A 2 (13.0) .512 1 (0.5) .020 (4.5) .177 (13.0) .512 (27.5) 1.083 COM 6 3 5 2 4 1 (12.5) Dia .492 (11.5) .453 (13.0) .512 Supplement (1.5) .060 (2.0) Typ .079 (4.8) .189 (2.0) .079 (7.9) .311 C94 (12.7) .500 www.nkkswitches.com Effective Panel Thickness: .217" (5.5mm) maximum Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: NKK Switches: MB2065SS2W13-CA MB2011SS1W02-CC MB2065SB1G01-BA MB2065SS2W03-BA MB2065SS2W30-CA MB2085SS2W30-BA MB2011SB3W02 MB2011SB3G01-CA MB2011SA2G31-CA MB2011SS2G13-CA MB2185SD3W01 MB2016SD1W01-BC MB2011LS1W01-CG-RO MB2011SA2W31-CC MB2011SB1W02-EA-RO MB2011SS1G40 MB2011SS1G40-CC MB2011SS1W13-CC MB2065SS2W13-CB MB2085LD1G03 MB2011SB1W01-4F-A-RO MB2085LS1W01-CA-RO MB2011SA2G31-CF MB2011SS2G30-CF MB2065SS1W31-BH MB2065SS2W30-BC MB2085SS2W30-BC MB2085SS1W01-CE MB2085SS2W30-BB MB2011LD1W01-BA-RO MB2011LS4W01-CH/AT507M-RO MB2065LS1G01-BA MB2085SS1W01-CA-RO MB2065LS1W01-BB MB2085LS1W01-BB MB2085LS1G01-BB MB2011SD3G01-CG MB2061SS1G01-CH MB2011SB3W03-DA MB2011SB1W01-4C-A-RO MB2011SS1W30/UC-BH-RO MB2011SS2W13-CE MB2061LS1W01-BA-RO MB2085SS2W30-CC MB2185SS1W01-CA-RO MB2011SS2G30-RO MB2011SS1G30-CA MB2065SS1G-30-CA MB2065SS1G40-BA MB2065SS1W30/CUL MB2065SS2A30-CC MB2011SS1G30-BH MB2011SA2G31-CB MB2065SS1W45/CUL MB2011SS1W13-BG MB2085SS1W40-BA MB2085SS1W13-BA MB2065SA2W31 MB2085SS1W40-CC MB2061SS1G30 MB2061SS2W13-CA MB2181SS2W13 MB2065SS2W13-CC MB2011SS1G45-BA MB2011SS2G40-BA MB2011SA2G31-BE MB2011SA2W31-CA MB2011SS2W31-BC MB2011SS2G30-CG MB2011LS2G13/328 MB2185SS2W40-CB MB2065SS2W40-BC MB2011SS2G45-CG MB2181SS2G45-CA MB2085SS1W13 MB2011SS1W40-BC MB2065SS1W30-BA MB2011SS2G40-BC MB2065SS2G31 MB2061SS2W13 MB2061SS1G30-CA MB2061SS2W30-CA MB2011SA2W31-BA MB2011SS2A13/328-BA MB2011SS2A13/328 MB2011SS2W30-CA MB2011SS2W13/328 MB2061SS2W13-BA MB2011SS2G13-BC MB2011SS1G13 MB2011SS2G45-BA MB2061SS2G13-BC MB2065SS2W13-BA MB2065SS2W31-CA MB2065SS2G30-BG MB2011SS2A13-CA MB2011SS1W30-BC MB2181SS1G45 MB2061SS2W45-CA MB2011SS1W40