Enpirion(R) Power Datasheet EP5388QI 800mA PowerSoC Synchronous Buck Regulator With Integrated Inductor Product Overview Features The EP5388QI is a synchronous buck converter with integrated Inductor, PWM controller, MOSFETS, and Compensation providing the smallest possible solution size. The EP5388QI requires only two small MLCC capacitors to make a complete solution. Integration of the inductor greatly simplifies design, contains noise, reduces part count, and reduces solution footprint. Low output ripple ensures compatibility with RF systems. The EP5388QI operates at a switching frequency of 4 MHz, enabling this unprecedented level of integration and small external components. Type III voltage mode control is used to provide high noise immunity and wide control loop bandwidth. The small footprint makes this part ideal for space constrained portable applications. Shutdown current of <1uA extends battery life Output voltage level is programmed via a 3-pin VID selector providing seven pre-programmed output voltages along with an option for external resistor divider. * 3mm x 3mm x 1.1mm QFN package * Only two low cost MLCC caps required * 4 MHz switching frequency * High efficiency, up to 94% * Up to 800mA continuous output current * Wide 2.4V to 5.5V input range * VOUT Range: 0.6V to VIN - 0.5V * 3-Pin VID output voltage programming * 100% duty cycle capable * Less than 1 A standby current * Low VOUT ripple for RF compatibility * Short circuit and over current protection * UVLO and thermal protection * RoHS compliant; MSL 3 260C reflow Applications * * * * * * Noise sensitive RF applications Area constrained applications Wireless data applications Portable gaming devices Personal Media Players Advanced Mobile Processors, DSP, IO, Memory, Video, Multimedia Engines VSense ENABLE VIN Vin 4.7F 0603 VOUT Vout 47F 1206 EP5388QI VFB Voltage Select Figure 1. Integrated Inductor Technology VS2 GND Figure 2. Typical application circuit 1 02377 VS0 VS1 Decemeber 11, 2017 www.altera.com/enpirion Rev G EP5388QI Ordering Information Part Number TAMBIENT Rating (C) Package Description EP5388QI -40 to +85 16 pin (3mm x 3mm x 1.1mm) QFN T&R EP5388QI-E QFN Evaluation Board Packing and Marking Information: www.altera.com/support/reliability/packing/rel-packing-and-marking.html NC(SW) NC(SW) 16 15 Pin Assignments (Top View) VIN 2 13 ENABLE PGND 3 12 VS0 VFB 4 11 VS1 VSENSE 5 10 VS2 AGND 6 9 NC 8 VOUT PGND VOUT 1 7 14 NC(SW) Figure 3. EP5388QI Package Pin-out NOTE A: NC pins are not to be electrically connected to each other or to any external signal, ground, or voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage. NOTE B: White `dot' on top left is pin 1 indicator on top of the device package. Pin Description PIN NAME 1, 15, 16 NC(SW) 2,3 PGND 4 VFB 5 VSENSE 6 AGND 7,8 VOUT 9 NC FUNCTION NO CONNECT - These pins are internally connected to the common drain output of the internal MOSFETs. NC(SW) pins are not to be electrically connected to any external signal, ground, or voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage. Power Ground Feedback pin for external divider option. When using the external divider option (VS0=VS1=VS2= high) connect this pin to the center of the external divider. Set the divider such that VFB = 0.6V. The "ground" side of the external divider should be connected to AGND. This pin may be left unconnected when using Voltage Select pins (VS0-VS2) to set the output voltage. Sense pin for output voltage regulation. Refer to application section for proper configuration. Analog ground. This is the quiet ground for the internal control circuitry Regulated Output Voltage. Refer to application section for proper layout and decoupling. NO CONNECT - This pin should not be electrically connected to any external signal, voltage, or ground. This pin may be connected internally. However, this pin must be soldered to the PCB. 2 02377 Decemeber 11, 2017 www.altera.com/enpirion Rev G EP5388QI PIN NAME 10, 11, 12 VS0,VS1,VS2 13 14 ENABLE VIN FUNCTION Output voltage select. VS2=pin10 VS1=pin11, VS0=pin12. Selects one of seven preset output voltages or choose external divider by connecting pins to logic high or low. Refer to section on output voltage select for more detail. Output enable. Enable = logic high, disable = logic low. Input voltage pin. Refer to application section for proper layout and decoupling. Functional Block Diagram VIN UVLO Thermal Limit Current Limit ENABLE NC(SW) Soft Start P-Drive (-) Logic VOUT PWM Comp (+) N-Drive GND VSENSE Sawtooth Generator Compensation Network (-) Switch Error Amp VFB (+) DAC VREF Voltage Select Package Boundry VS0 VS1 VS2 Figure 4. Functional block diagram www.altera.com/enpirion Page 3 02377 Decemeber 11, 2017 Rev G EP5388QI Absolute Maximum Ratings CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond recommended operating conditions is not implied. Stress beyond absolute maximum ratings may cause permanent damage to the device. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. PARAMETER SYMBOL MIN MAX UNITS VIN -0.3 -0.3 -0.3 -65 7.0 VIN + 0.3 2.7 150 260 2000 V V V C C V Input Supply Voltage Voltages on: ENABLE, VSENSE, VS0-VS2 Voltage on: VFB Storage Temperature Range Reflow Temp, 10 Sec, MSL3 JEDEC J-STD-020C ESD Rating (based on Human Body Model) TSTG Recommended Operating Conditions PARAMETER Input Voltage Range Output Voltage Range Output Current Operating Ambient Temperature Operating Junction Temperature SYMBOL MIN MAX UNITS VIN VOUT IOUT TA TJ 2.4 0.603 0 -40 -40 5.5 VIN - 0.5 800 +85 +125 V V mA C C Thermal Characteristics PARAMETER SYMBOL Thermal Resistance: Junction to Ambient (0 LFM) Thermal Overload Trip Point Thermal Overload Trip Point Hysteresis JA TJ-TP TYP UNITS 100 +150 15 C/W C C Electrical Characteristics NOTE: TA = -40C to +85C unless otherwise noted. Typical values are at TA = 25C, VIN = 3.6V. CIN =4.7F 0603 MLCC, COUT = 47F 1206 MLCC. PARAMETER VOUT Initial Accuracy Line Regulation Load Regulation Temperature Variation Overall VOUT Accuracy (Line, Load, and Temperature combined) Dropout Resistance Dynamic Voltage Slew Rate Continuous Output Current Shut-Down Current PFET OCP Threshold Feedback Pin Voltage Feedback Pin Input Current VS0-VS1, Enable Voltage Threshold VS0-VS2 Pin Input Current SYMBOL VOUT_Initl VOUT_linel VOUT_load VOUT_templ VOUT_All TEST CONDITIONS TA = 25C, 2.4V VIN 5.5V 2.4V VIN 5.5V 0A ILOAD 800mA -40C TA +85C 2.4V VIN 5.5V -40C TA +85C 0A ILOAD 800mA MIN -2% IOUT -3% ISD ILIM VFB 0.975 -20C TA +85C -40C TA +85C Enable = Low %/V %/mA %/C 400 500 m 1.5 2.025 V/ms 800 750 mA A mA V 0.75 1000 0.603 100 Pin = Low Pin = High IVSX UNITS +3% IFB VTH MAX +2% 0.0566 0.0003 0.0078 RDROPOUT Vslew TYP 0.0 1.4 nA 0.4 VIN 1 nA www.altera.com/enpirion Page 4 02377 Decemeber 11, 2017 Rev G EP5388QI PARAMETER Operating Frequency PFET On Resistance NFET On Resistance Soft-Start Operation Soft-Start Slew Rate VOUT Rise Time SYMBOL TEST CONDITIONS MIN TYP 4 340 270 MAX UNITS MHz m m FOSC RDS(ON) RDS(ON) VSS VID programming mode 0.975 1.5 2.025 V/ms TSS VFB programming mode 0.784 1.2 1.628 ms 95 95 90 90 85 85 80 80 Efficiency (%) Efficiency (%) Typical Performance Characteristics 75 70 75 70 65 65 60 60 55 55 50 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 50 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 Load Current (A) Load Current (A) Efficiency, VIN = 3.3V, VOUT = 1.2V, 1.5V,1.8V, 2.5V. Efficiency, VIN = 3.7V, VOUT = 1.2V, 1.5V,1.8V, 2.5V. 95 90 85 Efficiency (%) 80 75 70 65 60 55 50 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 Load Current (A) Efficiency, VIN = 5V, VOUT = 1.2V, 1.5V,1.8V, 2.5V, 3.3V. Output Ripple, VIN = 5V, VOUT = 1.2V; Load = 500mA. www.altera.com/enpirion Page 5 02377 Decemeber 11, 2017 Rev G EP5388QI Output Ripple, VIN = 5V, VOUT = 1.8V; Load = 500mA. Output Ripple, VIN = 5V, VOUT = 2.5V; Load = 500mA. Output Ripple, VIN = 5V, VOUT = 3.3V; Load = 500mA. Output Ripple, VIN = 3.3V, VOUT = 1.2V; Load = 500mA. Output Ripple, VIN = 3.3V, VOUT = 1.8V; Load = 500mA. Output Ripple, VIN = 3.3V, VOUT = 2.5V; Load = 500mA. www.altera.com/enpirion Page 6 02377 Decemeber 11, 2017 Rev G EP5388QI Transient, VIN = 5.0V, VOUT = 1.2V, Load = 0-800mA. Transient, VIN = 5.0V, VOUT = 3.3V, Load = 0-800mA. Transient, VIN =3.3V, VOUT = 1.2V, Load = 0-800mA. Transient, VIN = 3.3V, VOUT = 1.8V, Load = 0-800mA. Startup, VIN = 3.6V, VOUT = 1.5V, Load = 500mA. Enable in light blue; Vout in Dark blue. Shutdown, VIN = 3.6V, VOUT = 1.5V, Load = 500mA. Enable in light blue; Vout in Dark blue. www.altera.com/enpirion Page 7 02377 Decemeber 11, 2017 Rev G EP5388QI Detailed Description significantly reduces parasitic effects that can harm loop stability, and makes layout very simple. Functional Overview The EP5388QI is a complete DCDC converter solution requiring only two low cost MLCC capacitors. MOSFET switches, PWM controller, Gate-drive, compensation, and inductor are integrated into the tiny 3mm x 3mm x 1.1mm package to provide the smallest footprint possible while maintaining high efficiency, low ripple, and high performance. The converter uses voltage mode control to provide the simplest implementation and high noise immunity. The device operates at a 4MHz switching frequency. The high switching frequency allows for a wide control loop bandwidth providing excellent transient performance. The high switching frequency further enables the use of very small components making possible this unprecedented level of integration. Altera's proprietary power MOSFET technology provides very low switching loss at frequencies of 4 MHz and higher, allowing for the use of very small internal components, and high performance. Integration of the magnetics virtually eliminates the design/layout issues normally associated with switch-mode DCDC converters. All of this enables much easier and faster incorporation into various applications to meet demanding EMI requirements. Output voltage is chosen from seven preset values via a three pin VID voltage select scheme. An external divider option enables the selection of any voltage in VIN to 0.6V range. This reduces the number of components that must be qualified and reduces inventory burden. The VID pins can be toggled on the fly to implement glitch free dynamic voltage scaling. Protection features include under-voltage lock-out (UVLO), over-current protection (OCP), short circuit protection, and thermal overload protection. Integrated Inductor Altera has introduced the world's first product family featuring integrated inductors. The EP5388QI utilizes a proprietary low loss integrated inductor. The use of an internal inductor localizes the noises associated with the output loop currents. The inherent shielding and compact construction of the integrated inductor reduces the radiated noise that couples into the traces of the circuit board. Further, the package layout is optimized to reduce the electrical path length for the AC ripple currents that are a major source of radiated emissions from DCDC converters. The integrated inductor Stable Over Wide Range of Operating Conditions The EP5388QI utilizes an internal type III compensation network and is designed to provide a high degree of stability over a wide range of operating conditions. The device operates over the entire input and output voltage range with no external modifications required. The very high switching frequency allows for a very wide control loop bandwidth. Soft Start Internal soft start circuits limit in-rush current when the device starts up from a power down condition or when the "ENABLE" pin is asserted "high". Digital control circuitry limits the VOUT ramp rate to levels that are safe for the Power MOSFETS and the integrated inductor. The EP5388QI has two soft start operating modes. When VOUT is programmed using a preset voltage in VID mode, the device has a constant slew rate. When the EP5388QI is configured in external resistor divider mode, the device has a constant VOUT ramp time. Output voltage slew rate and ramp time is given in the Electrical Characteristics Table. Excess bulk capacitance on the output of the device can cause an over-current condition at startup. Maximum allowable output capacitance depends on the device's minimum current limit, the output current at startup, the minimum soft-start time and the output voltage (all are listed in the Electrical Characteristics Table). The total maximum capacitance on the output rail is estimated by the equation below: COUT_MAX = 0.7 * (ILIMIT - IOUT) * tSS / VOUT COUT_MAX = maximum allowable output capacitance ILIMIT = minimum current limit = 0.8A IOUT = output current at startup VOUT = output voltage 0.7 = margin factor tSS(VFB) = min soft-start time = 0.784ms External feedback setting tSS(VID) = VOUT [V] / 2.025 [V/ms] VID setting www.altera.com/enpirion Page 8 02377 Decemeber 11, 2017 Rev G EP5388QI The soft-start time in VID setting is different than External Feedback (VFB) setting, so be sure to use the correct value when calculating the maximum allowable output capacitance. NOTE: Do not use excessive output capacitance since it may affect device stability. The EP5388QI has high loop bandwidth and 80F is all that is needed for transient response optimization. Over Current/Short Circuit Protection controller may not be properly powered if ENABLE is tied directly to AVIN during startup. It is recommended to use an external RC circuit to delay the ENABLE voltage rise so that the internal controller has time to startup into regulation (see circuit below). The RC circuit may be adjusted so that AVIN and PVIN are above UVLO before ENABLE is high. The startup time will be delayed by the extra time it takes for the capacitor voltage to reach the ENABLE threshold. NOTE: This pin must not be left floating. The current limit function is achieved by sensing the current flowing through a sense P-MOSFET which is compared to a reference current. When this level is exceeded the P-FET is turned off and the N-FET is turned on, pulling VOUT low. This condition is maintained for a period of 1ms and then a normal soft start is initiated. If the over current condition still persists, this cycle will repeat in a "hiccup" mode. Under Voltage Lockout During initial power up an under voltage lockout circuit will hold-off the switching circuitry until the input voltage reaches a sufficient level to insure proper operation. If the voltage drops below the UVLO threshold the lockout circuitry will again disable the switching. Hysteresis is included to prevent chattering between states. Enable The ENABLE pin provides a means to shut down the converter or enable normal operation. A logic low will disable the converter and cause it to shut down. A logic high will enable the converter into normal operation. In shutdown mode, the device quiescent current will be less than 1 uA. At extremely cold conditions below -30C, the Figure 5. ENABLE Delay Circuit Thermal Shutdown When excessive power is dissipated in the chip, the junction temperature rises. Once the junction temperature exceeds the thermal shutdown temperature the thermal shutdown circuit turns off the converter output voltage thus allowing the device to cool. When the junction temperature decreases to a safe operating level, the device will go through the normal startup process. The specific thermal shutdown junction temperature and hysteresis values can be found in the thermal characteristics table. Application Information Output Voltage Select To provide the highest degree of flexibility in choosing output voltage, the EP5388QI uses a 3 pin VID, or Voltage ID, output voltage select arrangement. This allows the designer to choose one of seven preset voltages, or to use an external voltage divider. Internally, the output of the VID multiplexer sets the value for the voltage reference DAC, which in turn is connected to the noninverting input of the error amplifier. This allows the use of a single feedback divider with constant loop gain and optimum compensation, independent of the output voltage selected. Table 1 shows the various VS0-VS2 pin logic states and the associated output voltage levels. A logic "1" indicates a connection to VIN or to a "high" logic voltage level. A logic "0" indicates a connection to ground or to a "low" logic voltage level. These pins can be either hardwired to VIN or GND or alternatively can be driven by standard logic levels. Logic low is defined as VLOW 0.4V. Logic high is defined as VHIGH 1.4V. Any level between these www.altera.com/enpirion Page 9 02377 Decemeber 11, 2017 Rev G EP5388QI two values is indeterminate. These pins must not be left floating. VS2 0 0 0 0 1 1 1 1 VS1 0 0 1 1 0 0 1 VS0 0 1 0 1 0 1 0 VOUT 3.3V 2.5V 1.8V 1.5V 1.25V 1.2V 0.8V User 1 1 Selectable Table 1. VID voltage select settings External Voltage Divider As described above, the external voltage divider option is chosen by connecting the VS0, VS1, and VS2 pins to VIN or logic "high". The EP5388QI uses a separate feedback pin, VFB, when using the external divider. VSENSE must be connected to VOUT as indicated in Figure 6. VSense ENABLE VIN Vin 4.7F 0603 47F 1206 Ra EP5388QI VFB VS0 VS1 VS2 VOUT Vout Rb GND Figure 6. External Divider application circuit The output voltage is selected by the following formula: VOUT = 0.603V (1 + Ra Rb ) Ra must be chosen as 200K to maintain loop gain. Then Rb is given as: 1.206 x10 5 = Rb VOUT - 0.603 VOUT can be programmed over the range of 0.6V to VIN-0.5V. Dynamically Adjustable Output The EP5388QI is designed to allow for dynamic switching between the predefined VID voltage levels. The inter-voltage slew rate is optimized to prevent excess undershoot or overshoot as the output voltage levels transition. The slew rate is identical to the soft-start slew rate of 1.5V/mS. Dynamic transitioning between internal VID settings and the external divider is not allowed. Power-Up/Down Sequencing During power-up, ENABLE should not be asserted before VIN. During power down, the VIN should not be powered down before the ENABLE. Tying PVIN and ENABLE together during power-up or powerdown meets this requirement. Pre-Bias Start-up The EP5388QI does not support startup into a prebiased condition. Be sure the output capacitors are not charged or the output of the EP5388QI is not pre-biased when the EP5388QI is first enabled. Input and Output Capacitors The input capacitance requirement is 4.7uF 0603 MLCC. Altera recommends that a low ESR MLCC capacitor be used. The input capacitor must use a X5R or X7R or equivalent dielectric formulation. Y5V or equivalent dielectric formulations lose capacitance with frequency, bias, and with temperature, and are not suitable for switch-mode DC-DC converter input filter applications. A variety of output capacitor configurations are possible depending on footprint and ripple requirements. For applications where VIN range is up to 5.5V, it is recommended to use a single 47uF 1206 MLCC capacitor. Ripple performance can be improved by using 2 x 22uF 0805 MLCC capacitors. A single 10uF 0805 MLCC can be used if VOUT programming is accomplished using an external divider, with the addition of a 10pF phase lead capacitor as shown in Figure 7. Note that in this configuration, VSENSE should NOT be connected to VOUT. This modification is necessary to ensure proper operation of the compensation network over the range of operating conditions. As described in the Soft Start section, there is a limitation on the maximum bulk capacitance that can be placed on the output of this device. Please refer to the section on Soft Start for more details. The output capacitor must use a X5R or X7R or equivalent dielectric formulation. Y5V or equivalent dielectric formulations lose capacitance with frequency, bias, and temperature and are not suitable for switch-mode DC-DC converter output filter applications. www.altera.com/enpirion Page 10 02377 Decemeber 11, 2017 Rev G EP5388QI VSense ENABLE VIN Vin 4.7F 0603 VOUT 10F 0805 Ra EP5388QI VFB VS0 VS1 VS2 X Vout Rb 10pF GND Figure 7. Applications circuit for COUT = 1 x 10uF 0805 Layout Considerations* *Optimized PCB layout file is downloadable from the Altera website to assure first pass design success. Refer to Figure 8 for the following layout recommendations. Recommendation 1: The input and output filter capacitors should be placed as close to the EP5388QI as possible to reduce EMI from input and output loop AC currents. This reduces the physical area of these AC current loops. Recommendation 2: The system ground plane should be the first layer immediately below the surface layer (PCB layer 2). If it is not possible to make PCB layer 2 the system ground plane, a local ground island should be created on PCB layer 2 under the Altera Enpirion device and including the area under the input and output filter capacitors. This ground plane, or ground island, should be continuous and uninterrupted underneath the Altera Enpirion device and the input and output filter capacitors. Recommendation 3: The surface layer ground pour should include a "slit" as shown in Figure 8 to separate the input and output AC loop currents. This will help reduce noise coupling from the input current loop to the output current loop. Recommendation 4: Multiple small vias (approximately 0.25mm finished diameter) should be used to connect the ground terminals of the input and output capacitors, and the surface ground pour under the device, to the system ground plane. If a local ground island is used on PCB layer 2, the vias should connect to the ground island and continue down to the PCB system ground plane. Recommendation 5: The AGND pin should be connected to the system ground plane using a via as described in recommendation 4. AGND must NOT be connected to the surface layer ground pour. Recommendation 6: As with any switch-mode DCDC converter, do not run any sensitive signal or control lines under the converter package. Figure 8. PCB layout recommendation www.altera.com/enpirion Page 11 02377 Decemeber 11, 2017 Rev G EP5388QI Recommended PCB Footprint Figure 9. Recommended PCB Footprint www.altera.com/enpirion Page 12 02377 Decemeber 11, 2017 Rev G EP5388QI Package Dimensions Figure 10. EP5388QI Package Dimensions www.altera.com/enpirion Page 13 02377 Decemeber 11, 2017 Rev G EP5388QI Revision History Rev Date Change(s) F June, 2017 Max Bulk Cap (COUT_MAX) equation updated to reflect loading and startup time (with margin added) G Dec, 2017 Revision History added Contact Information Altera Corporation 101 Innovation Drive San Jose, CA 95134 Phone: 408-544-7000 www.altera.com (c) 2013 Altera Corporation--Confidential. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. www.altera.com/enpirion Page 14 02377 Decemeber 11, 2017 Rev G