D Montage und Verdrahtung Helligkeitssensor UP 255/01 5WG1 255-4AB01 AP 255/02 5WG1 255-4AB02 fur Schalt- / Dimmaktor N 526/02 Stand: Mai 2010 Produkt- und Funktionsbeschreibung Die Helligkeitssensoren UP 255/01 und AP 255/02 dienen zum Messen der Arbeitsplatz-/Raumbeleuchtung. Die Sensoren sind ausschliesslich fur den Anschluss an den Schalt-/ Dimmaktor N 526/02 vorgesehen. Von diesem wird die Elektronik eines Helligkeitssensors mit Spannung versorgt. Es stehen 2 Varianten des Helligkeitssensors zur Verfugung: - UP-Helligkeitssensor UP 255/01 zum Einbau in einer Hohlwanddose oder UP-Dose nach DIN 49073-GB-T-M1E1 (02/90), 58mm (Standard), Tiefe 40mm, - AP-Helligkeitssensor AP 255/02 im Aufputzgehause ( 75 mm, Hohe 26 mm). Ein Helligkeitssensor wird mit jeweils zwei wei lackierten Lichtleitstaben geliefert ( 1 x Lichtleitstab mit gerader Lichteintrittsflache und 1 x Lichtleitstab mit schrager (30) Lichteintrittsflache). Diese sind wahlweise einsteckbar. Normalerweise ist der Lichtleitstab mit gerader Lichteintrittsflache zu verwenden. Durch Einsatz des Lichtleitstabes mit schrager (30) Lichteintrittsflache kann bei Bedarf die Richtung des Lichterfassungskegels verschoben werden (siehe Bilder 5 und 6). Anschlussbeispiel * Das Gerat kann fur feste Installation in trockenen Innenraumen verwendet werden. * Die Anschlussleitung zum Helligkeitssensor muss entsprechend DIN VDE 0100 Teil 520 installiert werden und darf bis zu 100m lang sein. V GEFAHR * Es durfen keine Leitungen mit 230V AC in die Unterputzdose bzw. das AP-Gehause des Helligkeitssensors eingefuhrt werden. * Das Verbinden der Sensor-Steckklemmen mit 230V Netzspannung oder der Busleitung fuhrt zur Zerstorung des Gerates (Brandgefahr). * Das Metallgehause des Helligkeitssensors darf nicht geoffnet werden. * Bei der Planung und Errichtung von elektrischen Anlagen sind die einschlagigen Richtlinien, Vorschriften und Bestimmungen des jeweiligen Landes zu beachten. UP-Helligkeitssensor UP 255/01 - Das Gerat ist zum Einbau in einer Hohlwanddose oder UP-Dose nach DIN 49073-GB-T-M1E1 (02/90), 58mm (Standard), Tiefe 40mm, vorgesehen. - Der UP-Helligkeitssensor UP 255/01 wird in Geratedosen mittels der mitgelieferten Schraubbefestigungen (ohne Krallen) eingebaut (siehe Bild 2). - Der Anschluss der Versorgungsspannung und Ausgangsspannung erfolgt uber eine 3-polige Steckklemme (schraubenlose Steckklemme fur eindrahtige Leiter). Die Steckklemme befindet sich auf der Ruckseite des Gerates. B2 B1 - Empfohlene Leiterfarben: schwarz = 0V (GND), gelb = Ausgangssignal (OUT), wei = +5V (VCC). D2 D2 D2.4 D2.4 D2 D2.1 D2.2 D2.3 Bild 4: Anschliessen / Abklemmen der Anschlussleitung Montagehinweise * Der Helligkeitssensor ist oberhalb der Arbeitsflache (=Mess-flache) z.B. an der Raumdecke zu installieren. Der fur die ortlichen Lichtverhaltnisse erforderliche Lichtleitstab ist ca. 15mm tief in das Gerat bis zum Anschlag einzuschieben. Der Sensor muss mit der Langsachse des Lichtleitstabes senkrecht nach unten zeigend ausgerichtet werden. * Es muss sichergestellt sein, dass der Helligkeitsfuhler nur indirektes, reflektiertes Licht misst. Direkt in den Lichtleitstab einfallende Sonnenstrahlen oder Lichtstrahlen einer Leuchte fuhren zu Fehlmessungen, die die Regelung beeintrachtigen. * Eine Kalibrierung des Sensors ist nicht unbedingt erforderlich. Je nach Reflexionsgrad der Oberflachen der Raumausstattung konnen sich jedoch groere Unterschiede bei der Helligkeitserfassung ergeben. Wird eine moglichst genaue Konstantlichtregelung gefordert, so ist eine Kalibrierung des Sensors durchzufuhren, um so eine moglichst genaue Helligkeitsmessung sicherzustellen (siehe Applikationsprogramm-Beschreibung zum N 526/02). * Bei Verwendung des wei lackierten Lichtleitstabes mit gerader Lichteintrittsflache (Standard-Lichtleitstab) ergibt sich der in Bild 5 gezeigte Erfassungskegel. instabus EIB E2 S ens or 1 GND GND VCC VCC IN OUT B4 H e llig k e its s e n s o r U P 2 5 5 b zw . AP 255 GND S en s or 2 E1 E3 VCC IN GND S en s or 3 B5 B3 Bild 2: Montage des UP-Helligkeitssensors UP 255/01 IN S c h a lt- / D im m a k to r N 5 2 6 /0 2 B1 B2 B3 Technische Daten Messbereich * 0 bis 1500 Lux (bei einem Reflexionsgrad der Arbeitsflache von ca. 30%) Spannungsversorgung * Die Spannungsversorgung (5 Volt) erfolgt uber den Schalt-/ Dimmaktor N 526/02. Anschlusse * 3-polige Steckklemme zum Anschluss der Leiter fur Versorgungs- und Ausgangsspannung ( 0,6 ... 0,8 mm eindrahtig) Mechanische Daten UP-Helligkeitssensor UP 255/01 * Metallgehause mit Deckel (Polystyrol (PS)), wei, flammwidrig) zur Montage in einer Hohlwanddose oder UP-Dose nach DIN 49073-GB-T-M1E1 (02/90), 58mm (Standard), Tiefe 40mm. B4 B5 AP-Helligkeitssensor AP 255/02 - Das Gerat wird mit einem Aufputzgehause 75mm, Hohe 26mm, Deckel mit Bajonettverschluss, geliefert (s. Bild 3). - Das Gehause-Unterteil des AP-Helligkeitssensors AP255/02 ist uber dem Auslass der Sensorleitung an der Zimmerdecke zu befestigen. - Der Anschluss der Versorgungsspannung und Ausgangsspannung erfolgt uber eine 3-polige Steckklemme (schraubenlose Steckklemme fur eindrahtige Leiter) auf der Ruckseite des Gerates. C2 Lage und Funktion der Anzeige- und Bedienelemente A4 A1 N526/02 GND GND (SZ) OUT (GB) IN VCC (WS) VCC Phys. Adr. Sensor No. A2 A3 A6 Bild 1: Lage der Bedienelemente A1 A2 A3 A4 A5 A6 Unterseite der Abdeckung fur die UP-Dose bzw. das AP-Gehause Typenschild Metallgehause Steckklemme GND Steckklemme OUT fur Sensorausgangsspannung Steckklemme VCC fur Sensorversorgungsspannung (+5V) E7 Bild 5: Erfassungskegel bei gerader Lichteintrittsflache E1 E2 E3 E4 E5 E6 E7 Decke Metallgehause des Sensors Lichtleitstab Langsachse des Lichtleitstabes Winkel ca. 15 Winkel ca. 15 Messflache (Arbeitsflache) * Der wei lackierte Lichtleitstab mit schrager Lichteintrittsflache und dem im Bild 6 gezeigten Erfassungskegel sollte nur dann verwendet werden, wenn der Fuhler nicht direkt oberhalb, sondern nur seitlich versetzt uber der Flache montiert werden kann, deren Helligkeit er messen soll. E2 C3 Elektrische Sicherheit * Schutzart(nach EN 60529): IP 20 fur UP 255/01 IP 20 fur AP 255/02 Umweltbedingungen * Umgebungstemperatur im Betrieb: - 5 ... + 45 C * Lagertemperatur: - 25 ... + 70 C * Rel. Feuchte (nicht kondensierend): 5% ... 93% E5 E4 Deckel mit Befestigungslochern Lichtleitstab Metallgehause des Helligkeitssensors UP 255/01 Befestigungsschrauben Steckklemme fur Sensorleitung AP-Helligkeitssensor AP 255/02 * Aufputzgehause (Polystyrol (PS)), wei, flammwidrig, Kabeleinlass durch Ausbruche im Gehauseboden), 75 mm, Hohe 26 mm, Bajonettverschluss. A5 E6 VCC C4 E3 C1 E7 C4 C5 E4 Deckel mit Bajonettverschluss Lichtleitstab Metallgehause des Helligkeitssensors AP 255/02 Steckklemme fur Sensorleitung Unterteil fur AP-Gehause E8 Bild 6: Erfassungskegel bei schrager Lichteintrittsflache E1 E2 E3 E4 E5 Steckklemmen abziehen (Bild 4) - Die Steckklemme (D2) besteht beim UP 255/01 aus drei Teilen (D2.1, D2.2, D2.3) und beim AP 255/02 aus einem Teil mit Klemmkontakten. - Den Schraubendreher vorsichtig in den Drahteinfuhrungsschlitz des mittleren Teils der Steckklemme einfuhren und die Steckklemme aus dem Metallgehause ziehen. Achtung: Beim Entfernen der Steckklemme darauf achten, dass die Lei-ter bzw. die Stifte durch den Schraubendreher nicht kurzgeschlossen werden. Abklemmen der Leitung (Bild 4) - Die Steckklemme (D2) abziehen und die Leiter (D2.4) der Anschlussleitung, bei gleichzeitigem Hin- und Herdrehen, herausziehen. Steckklemmen aufstecken (Bild 4) - Die Steckklemme (D2) auf die Kontaktstifte stecken und bis zum Anschlag in das Metallgehause drucken. - Anschliessen der Leitung (Bild 4) - Die Steckklemme (D2) ist fur eindrahtige Leiter mit 0,6... 0,8 mm geeignet. - Die Leiter (D2.4) ca. 5 mm abisolieren und in Klemme (D2) stecken. E6 E5 C5 Bild 3: Montage des AP-Helligkeitssensors AP 255/02 C1 C2 C3 E1 E6 E7 E8 Decke Sensorgehause Lichtleitstab Langsachse des Lichtleitstabes Messachse (um ca. 18 gegenuber der Langsachse verschoben) Winkel ca. 15 (bezogen auf die Messachse) Winkel ca. 15 (bezogen auf die Messachse) Messflache (Arbeitsflache) * Beim Ausrichten des Lichtleitstabes mit schrager Lichteintrittsflache ist zu beachten, dass durch seinen Einsatz die Messflache, die der Sensor sieht", um 18 zur langeren Seite des Lichtleitstabes hin verschoben wird. Allgemeine Hinweise * * Ein defektes Gerat ist an die zustandige Geschaftsstelle der Siemens AG zu senden. Bei zusatzlichen Fragen zum Produkt wenden Sie sich bitte an unseren Technical Support: +49 (0) 180 50 50-222 +49 (0) 180 50 50-223 www.siemens.de/automation/support-request 251543.41.15 DS07 GB Brightness sensor UP 255/01 5WG1 255-4AB01 AP 255/02 5WG1 255-4AB02 for switch/dim actuator N 526/02 Mounting and wiring * The device may only be used for permanent interior installations in dry rooms. * The connecting cable to the brightness sensor must be installed according to DIN VDE 0100 section 520 with a maximum length of 100 m. D2 V DANGER As at: May 2010 Product and functional description A brightness sensor UP 255/01 or AP 255/02 is used to measure and control the lighting in the workplace or in the room. The sensor is solely intended for connection to the switch/dim actuator N 526/02. The electronics of the brightness sensor is supplied with power via the switch/dim actuator N 526/02. Two versions of the brightness sensor are available: - Brightness sensor UP 255/01 for insertion in a cavity wall box or flush-type box according to DIN 49073-GB-T-M1E1 (02/90), 58 mm (standard), depth 40 mm. - Brightness sensor AP 255/02 in a surface-mounted housing ( 75 mm, depth 26 mm). The brightness sensor is supplied in both variants, each with two white sprayed optical fibres (1 x optical fibre with an even surface for light incidence and 1 x optical fibre with a tilted surface (30)). This can be inserted as required. Normally the optical fibre with an even surface should be used. By use of the optical fibre with a tilted surface (30) the direction of the light detection cone can be adapted to the local needs (see Diagrams 5, 6). D2 * No cables with 230 V AC may be inserted in the flush-type box or surface-mounted box of the brightness sensor. * Connecting the plug-in terminals to the 230 V mains voltage or to the bus cable leads to the device being damaged (risk of fire). * The metal housing of the device may not be opened. * For planning and construction of electric installations, the relevant guidelines, regulations and standards of the respective country are to be considered. Brightness sensor UP 255/01 - The device is intended for insertion in a cavity wall box or flush-type box according to DIN 49073-GB-T-M1E1 (02/90), 58 mm (standard), depth 40 mm. - The brightness sensor UP 255/01 is inserted in switch boxes using the supplied screw fixing (without claws) (see Diagram 2). - The connection of the supply voltage and output voltage is carried out via a 3-pole plug-in terminal (plug-in screw-less terminal for single-core conductors). The plug-in terminal is located on the back of the device. B2 Connection example B1 instabus EIB Connecting the cable (Diagram 4) - The plug-in terminal (D2) is suitable for single-core conductors with 0.6... 0.8 mm. - Strip approx. 5 mm of insulation from the conductor (D2.4) and place in the terminal (D2) (black = 0 V, yellow = output signal, white = +5 V). S ens or 1 GND GND VCC VCC IN S ens or 2 OU T Diagram 4: Connecting/disconnecting the connecting cable Notes for the installation * The brightness sensor should be installed above the measurement plane (work place surface] e.g. at the ceiling. That optical fibre which fits best to the local lighting conditions has to be inserted into the sensor housing until the limit stop (15 mm). The sensor must be aligned vertically with the longitudinal axis of the optical fibre and point downwards. * It must be ensured that the brightness sensor only measures indirect, reflected light. Any direct sunlight falling on the optical fibre or direct light beams from a lamp lead to errors during measurement which impair the controller. * A calibration of the sensor is not always required. Differences in the brightness detection may however occur depending on the degree of reflection on the surface of the equipment in the room. If there is a need for a precise measurement and control, a calibration of the sensor (see application program description of the N 526/02) should be carried out. * When using the white sprayed optical fibre with an even surface, the detection cone indicated in Diagram 5 is given. E2 B4 VCC E1 IN S ens or 3 E3 GND VCC IN B5 S w itch/dim actu ator N 52 6/02 B3 E6 B1 B2 B3 Measuring range * 0 to 1500 lux (at a 30% degree of reflection from the workplace) Power supply * The power supply (5 volts) is carried out via the switch/dim actuator N 526/02 Connections * 3-pole plug-in terminal for connecting the supply and output voltage ( 0.6 ... 0.8 mm single-core) Mechanical data Brightness sensor UP 255/01 * Metal housing with lid (Polystyrol, white) for installation in a cavity wall box or flush-type box according to DIN 49073- GB-T-M1E1 (02/90), 58 mm (standard), depth 40 mm B4 B5 Electrical safety * Type of protection (according to EN 60529): IP 20 for UP 255/01 IP 20 for AP 255/02 Environmental conditions * Ambient operating temperature: -5 ... +45 C * Storage temperature: -25 ... +70 C * Relative humidity (not condensing): 5% ... 93% Location / function of the operating and display elements A4 A1 Lid with fixing holes Optical fibre Metal housing of the brightness UP 255/01 Fixing screws Plug-in terminal for sensor cable E4 sensor Brightness sensor AP 255/02 - The device is supplied in a surface-mounted housing, 75 mm, height 26 mm, bayonet catch (see Diagram 3). - The housing should be mounted on the ceiling above the outlet of the sensor cable. - The connection of the supply voltage and output voltage is carried out via a 3-pole plug-in terminal (plug-in screw-less terminal for single-core conductors). The plug-in terminal is located inside the surface-mounted housing on the back of the device. C2 GND (BK) GND OUT (YE) IN VCC (WH) VCC Phys. Adr. Sensor No. A3 A6 Diagram 1: Location of the operating and display elements A2 A3 A4 A5 A6 Underside of the cover for the flush-type box or the lid for the surface-mounted housing Type label Metal housing Plug-in terminal GND Plug-in terminal OUT for output voltage of sensor Plug-in terminal VCC for power supply of sensor (+5 V) Diagram 5: Detection cone of a fibre with an even surface E1 E2 E3 E4 E5 E6 E7 Ceiling Metal housing of the sensor Optical fibre Longitudinal axis of optical fibre Angle approx. 15 Angle approx. 15 Measurement plane (work surface) * The white sprayed optical fibre with a tilted surface and the detection cone indicated in Diagram 6 should be used if the sensor cannot be installed directly over the workplace where the brightness shall be measured. E2 C4 C3 E7 E6 C7 E5 C5 Diagram 3: Installation of the brightness sensor AP 255/02 C1 C2 C3 C4 C5 C6 C7 Lid with bayonet catch Optical fibre Brightness sensor AP 255/02 Plug-in terminal for sensor cable Lower part of the surface-mounted housing Fixing holes Cable entry holes Removing plug-in terminals (Diagram 4) - The plug-in terminal (D2) of the UP 255/01 consists of three sections (D2.1, D2.2, D2.3) and that of the AP 255/02 of one part with terminal contacts. - Carefully insert the screwdriver in the wire entry slot in the middle section of the plug-in terminal and pull the terminal out of the metal housing. Note: Care should be taken as there is a risk of shorting the wires or the terminal pins with the srewdriver. Disconnecting the cable (Diagram 4) - Remove the plug-in terminal (D2) and the conductor (D2.4) from the connecting cable by rotating it backwards and forwards simultaneously. Connecting plug-in terminals (Diagram 4) - Place the plug-in terminal (D2) on the contact pins and press the terminal into the metal housing until it reaches the stop. E1 E3 C1 N526/02 A2 E7 C6 Brightness sensor AP 255/02 * Surface-mounted housing (Polystyrol, white, cable entry via openings in base of housing), 75 mm, depth 26 mm, bayonet catch A1 E5 Diagram 2: Installation of the brightness sensor UP 255/01 Technical data A5 D2.4 D2 D2.1 D2.2 D2.3 B rig htn ess s ens or U P 2 55 or A P 2 55 GND D2.4 E4 E8 Diagram 6: Detection cone for tilted surface E1 E2 E3 E4 E5 E6 E7 E8 Ceiling Housing of the sensor Optical fibre Longitudinal axis of optical fibre Measuring axis (angle between the the longitudinal and the measuring axis approx. 18) Angle approx. 15 (related to the measuring axis) Angle approx. 15 (related to the measuring axis) Measurement plane [work place surface) * The optical fibre with a tilted surface should be aligned so that the measurement plane "seen" by the sensor is shifted for approx. 18 to the longer side of the sensor. General Notes * Any faulty devices should be returned to the local Siemens office. * If you have further questions concerning the product please contact our technical support: +49 (0) 180 50 50-222 +49 (0) 180 50 50-223 www.siemens.com/automation/support-request 251543.41.15 DS07