A
B
C
1234
D
A
B
C
D
123
Copyright FCI.
4
Pro/E File - REV C - 2009-06-09
#1$
0$angular
-
#0.0127
0.XXX
linear #0.076
0.XX
-
surface
#0.254
0.X
TOLERANCES UNLESS
OTHERWISE SPECIFIED
ASME Y14.5
ASME Y14.5
tolerance std
spec ref
sheet 1 of 4
Product - Customer Drw
-cat. no.
www.fci.com
C
10107246
dwg no
2.032mm PITCH
title
rev
3P SPIN MOTOR CONNECTOR ASSY.
Releasedrel level
-
product family2011-01-18JOEY NGappr
ELX-S-002566-1ecn no2011-01-18DENNIS GOHchr
5.000
A3
MM
2011-01-18DENNIS GOHeng
scalesizeprojection2010-09-17HK LIMdr
NOTES:
1 . MATERIAL
HOUSING: LCP BLACK, UL94V-0
CONTACT: COPPER ALLOY.
PLATING: SEE PAGE 4
2 . LOGO, CAVITY I.D. TO BE PLACE APPROXIMATELY WHERE SHOWN THEY ARE TO BE
INDENTED TO A DEPTH OF 0.13mm. HIGH SHINE MARKING IS ACCEPTABLE.
3. FLASH MUST REMAIN WITHIN THE SIZE LIMITS ESTABLISHED BY THE TOLERANCE.
NO FLASH IS ALLOWED ON DATUM ON DATUM SURFACES AND LOOSE FLASH MUST BE REMOVED.
EJECTOR PIN MARKS TO BE FLUSH WITH SURROUNDING SURFACE.
DO NOT USE SLICONE MOLD RELEASE.
4. GATE, EJECTOR PIN AND PARTING LINE LOCATIONS MUST BE APPROVED BY
CUSTOMER ENGINEERING PRIOR TO MOLD CONSTRUCTION.
5. PACKAGING: TAPE AND REEL AS PER PACKAGING SPEC GS-14-809.
6 . MECHANICAL REQUIREMENTS:
A. COMPRESSIBLE CONTACT SHALL HAVE A 140±30g FORCE AT 0.152mm HEIGHT
ABOVE DATUM -R- AS RECEIVED AND AFTER 20 CYCLES.
B. THE SPRING RATE OF THE PIN SHALL BE REFERENCE (245 OR 367±75) GRAMS/MM MEASURED AT 0.152mm
ABOVE DATUM -R-.
C. CONTACT SURFACE TO BE ROUNDED WITH CONTINUOUS SURFACE
CONTACT AND NO SHARP EDGES.
D. THE FORCE AND SPRING RATE MEASUREMENT SHALL BE CALCULATED
BY AVERAGING THE COMPRESSION AND DECOMPRESSION CURVES.
E. CONTACT RETENTION: 200gf MIN PER CONTACT.
7. ALL MATERIALS SHOULD BE COMPLIED WITH SPM ENVIRONMENT-RELATED SUBSTANCES
SPECIFICATION: 69707219*** AND SPM HALOGEN-FREE SPECIFICATION: 69820209***.
8. NO PLATING REQUIRED IN CUT OFF SECTIONS.
9. ALL SHARP EDGES MAY HAVE A RADII OF 0.25mm MAX.
10 . GATE VESTAGE OF (0.25mm MAX) ALLOWABLE TO OUT BOARD SIDES OF CONNECTOR.
11 . PIN HEAD SHOULD BE COVERED BY CONNECTOR HOUSING.
12. NO DENTS ARE ALLOWED ON PIN.
13. MEANS CPK STUDY IS REQUIRED.
14. ALL SHARP EDGES MAY HAVE A RADII OF 0.25mm MAX.
Cpk
PRODUCT NO. PACKAGING PLATING
10107246-001TRLF TAPE & REEL REFER TO PAGE 4
10107246-002TRLF
-
2011/01/20
-
2010/03/03
-
Dennis Goh
-
Dennis Goh
ELX-S-002566-1
C
Released
C
PDS: Rev :C STATUS:Released Printed: Feb 17, 2011
A
B
C
1234
D
A
B
C
D
123
Copyright FCI.
4
Pro/E File - REV C - 2009-06-09
A A
#1$
0$angular
-
#0.0127
0.XXX
linear #0.076
0.XX
-
surface
#0.254
0.X
TOLERANCES UNLESS
OTHERWISE SPECIFIED
ASME Y14.5
ASME Y14.5
tolerance std
spec ref
sheet 2 of 4
Product - Customer Drw
-cat. no.
www.fci.com
C
10107246
dwg no
2.032mm PITCH
title
rev
3P SPIN MOTOR CONNECTOR ASSY.
Releasedrel level
-
product family2011-01-18JOEY NGappr
ELX-S-002566-1ecn no2011-01-18DENNIS GOHchr
8.000
A3
MM
2011-01-18DENNIS GOHeng
scalesizeprojection2010-09-17HK LIMdr
R
SEE NOTE 2
SEE NOTE 2
2X C0.635
SECTION A-A
SEE DETAIL B
(FREE HEIGHT)
(COMPRESSED HEIGHT)
NOTE 6
(FREE HEIGHT)
DETAIL B
SCALE 20.000
SEE NOTE 11
Cpk
Cpk
Cpk
Cpk
Cpk
Cpk
10.922
3.810
3X 19.30#0.15
3X THRU7.366
3X THRU1.270
5.588
3X 1.270
3X 0.635
(2X )45$
TYP.0.635
TYP.0.635 TYP.0.318
3X 1.651
3X 0.686
3X 1.270
22.936#0.127
0.533
3 X ( )1.0
0.152
2.032
3X THRU0.813
3X MAX.2.286
60$
#5$
2X R
MAX
0.25
R MAX
0.25
R MAX
0.25
( )2.5
( )0.8
( )6.9
2.032
2X 45$
1.905
2X R
MAX
0.25
( )14.2
0.77
PRODUCT NO.
REFER TO TABLE
-
2011/01/20
-
2010/03/03
-
Dennis Goh
-
Dennis Goh
ELX-S-002566-1
C
Released
C
PDS: Rev :C STATUS:Released Printed: Feb 17, 2011
A
B
C
1234
D
A
B
C
D
123
Copyright FCI.
4
Pro/E File - REV C - 2009-06-09
#1$
0$angular
-
#0.0127
0.XXX
linear #0.076
0.XX
-
surface
#0.254
0.X
TOLERANCES UNLESS
OTHERWISE SPECIFIED
ASME Y14.5
ASME Y14.5
tolerance std
spec ref
sheet 3 of 4
Product - Customer Drw
-cat. no.
www.fci.com
C
10107246
dwg no
2.032mm PITCH
title
rev
3P SPIN MOTOR CONNECTOR ASSY.
Releasedrel level
-
product family2011-01-18JOEY NGappr
ELX-S-002566-1ecn no2011-01-18DENNIS GOHchr
8.000
A3
MM
2011-01-18DENNIS GOHeng
scalesizeprojection2010-09-17HK LIMdr
R
T
S
SEE DETAIL A
0.254 R T S
DETAIL A
SCALE 12.000
1$ DRAFT ALL AROUND
Cpk
Cpk
Cpk
Cpk
Cpk
0.152
2.311
2.159
1.245
R MIN.
2.540
R2.540
R MAX.
1.016
3.480
6X R0.254
R (X4)
1.219
4X 1.778
1.524#0.102
3.048
24.130
0.386
1.524
C MAX0.330
3X CONTACT0.300
(2X )45$
3.480
4.9534.953
4.3184.318
2.897
0.229
60$
8.382
( )1.6
( )1.1
( )2.2
( )0.3
3 X ( )1.5
(X2)2.591
6.655
3X THRU0.762
2X 6.35#0.15
3X 24.00#0.15
27.43#0.15
1.092#0.025
3X ( )1.7
( )0.5
( )1.6
( )20.5
PRODUCT NO.
REFER TO TABLE
-
2011/01/20
-
2010/03/03
-
Dennis Goh
-
Dennis Goh
ELX-S-002566-1
C
Released
C
PDS: Rev :C STATUS:Released Printed: Feb 17, 2011
A
B
C
1234
D
A
B
C
D
123
Copyright FCI.
4
Pro/E File - REV C - 2009-06-09
#1$
0$angular
-
#0.0127
0.XXX
linear #0.076
0.XX
-
surface
#0.254
0.X
TOLERANCES UNLESS
OTHERWISE SPECIFIED
ASME Y14.5
ASME Y14.5
tolerance std
spec ref
sheet 4 of 4
Product - Customer Drw
-cat. no.
www.fci.com
C
10107246
dwg no
2.032mm PITCH
title
rev
3P SPIN MOTOR CONNECTOR ASSY.
Releasedrel level
-
product family2011-01-18JOEY NGappr
ELX-S-002566-1 ecn no2011-01-18DENNIS GOHchr
8.000
A3
MM
2011-01-18DENNIS GOHeng
scalesizeprojection2010-09-17HK LIMdr
C
CONTACT AREA OTHER AREA TEST PAD AREA
SOLDER TAIL AREA
OTHER AREA OR SOLDER TAIL AREA
PLATING
OTHER AREA
OTHER AREA OR SOLDER TAIL AREA
3X (FOR PLATING ONLY)24.841
MIN1.524
( )4.19
0.635#0.254
MAX3.79
MIN2.79
PRODUCT NO. PLATING AREA
SOLDER TAIL AREA OTHER AREA CONTACT AREA TEST PAD AREA
10107246-001TRLF 0.051um MIN GOLD OVER
1.27um MIN NICKEL. 1.27um MIN NICKEL. 0.076um MIN GOLD OVER
1.27um MIN NICKEL. 1.27um MIN NICKEL.
10107246-002TRLF 1.27um MIN MATT TIN OVER
1.27um MIN NICKEL. 1.27um MIN NICKEL. 0.076um MIN GOLD OVER
1.27um MIN NICKEL. 1.27um MIN NICKEL.
PRODUCT NO.
REFER TO TABLE
-
2011/01/20
-
2010/03/03
-
Dennis Goh
-
Dennis Goh
ELX-S-002566-1
C
Released
C
PDS: Rev :C STATUS:Released Printed: Feb 17, 2011
