M39012/60-3001 - DELTA ELECTRONICS

INCH-POUND

MIL-PRF-39012/60D

14 July 2011

SUPERSEDING

MIL-PRF-39012/60C

14 May 2004

PERFORMANCE SPECIFICATION SHEET

CONNECTORS, RECEPTACLES, ELECTRICAL, COAXIAL, RADIO FREQUENCY

SERIES SMA (UNCABLED, SOCKET CONTACT, FLANGE MOUNTED, CLASS 2)

This specification is approved for use by all Departments and Agencies of the Department of Defense.

The requirements for acquiring the product described herein shall

consist of this specification sheet and MIL-PRF-39012.

Inches

.001

.004

.010

.029

.055

.075

0.02

0.10

0.25

0.74

1.40

1.91

.08

.088

.102

.165

.175

.218

2.0

2.24

2.59

4.19

4.45

5.54

.235

.245

.255

.300

.310

.338

5.97

6.22

6.48

7.62

7.78

8.49

.340

.342

.481

.510

.600

.625

8.64

8.69

12.22

19.25

15.24

15.88

FIGURE 1. General configuration.

AMSC N/A FSC 5935

Source: http://assist.dla.mil -- Downloaded: 2021-04-29T16:43ZCheck the source to verify that this is the current version before use.

MIL-PRF-39012/60D

NOTES:

1. Dimens ions are in inches.

2. Metric equivalents are given for information only.

3. Receptacle recommended for component part use and for use on panels with a .090 inch (2.29 mm)

maximum thickness.

4. All un-dimensioned pictorial configurations are for reference purposes only.

5. There shall be a solid barrier in the socket between the pin entry and the solder pocket to prevent

solder wicking.

6. Unless otherwise specified, tolerance is ±.005 (0.13 mm) on three-place decimals .010 inch

(0.25 mm) on two-place decimals and ±2° on angles.

7. Solder pockets shall be gold plated in accordance with ASTM B488, type II, class I.27.

8. Series SMA, socket contact interface shall be in accordance with MIL-STD-348.

FIGURE 1. General configuration - Continued.

Source: http://assist.dla.mil -- Downloaded: 2021-04-29T16:43ZCheck the source to verify that this is the current version before use.

MIL-PRF-39012/60D

ENGINEERING DATA:

Nominal impedance: 50 ohms.

Frequency range: Not rated.

Voltage rating: 335 volts rms maximum at sea level, 85 volts rms maximum at 70,000 feet.

Temperature rating: -65°C to +165°C.

REQUIREMENTS:

Dimensions and configuration: See figure 1 and MIL-STD-348.

Force to engage and disengage:

Longitudinal force: Not applicable.

Torque: 2 inch-pounds, maximum.

Coupling proof torque: Not applicable.

Inspection conditions: For each test of threaded coupling connector where the test is performed on

mated pairs, the pairs shall be torqued to 7 to 10 inch-pounds.

Mating characteristics: See MIL-STD-348 and figure 2 for dimensions.

Contacts with spring members.

Center contact (female):

Oversize test pin: .0375 + .0001/-.0000 inch.

Test pin finish: 16 microinches.

Insertion depth: .030/.045 inch.

Number of insertions: 3

Insertion force test:

Steel test pin diameter: .0370 + .0001/-.0000 inch

Insertion depth: .050/.075 inch.

Test pin finish: 16 microinches.

Insertion force: 2 pounds, maximum.

Source: http://assist.dla.mil -- Downloaded: 2021-04-29T16:43ZCheck the source to verify that this is the current version before use.

MIL-PRF-39012/60D

Withdrawal force test:

Steel test pin diameter: .0355 + .0000/-. 000 01 inc h.

Insertion depth: .050/.075 inch

Test pin finish: 16 microinches

Withdrawal force: 1 ounce, minimum

FIGURE 2. Test pin data.

Hermetic seal: Not applicable.

Leakage (pressurized connectors): Not applicable.

Insulation resistance: In accor danc e with test procedure EIA - 364-21, 5,000 mega oh ms mi nimum.

Center contact retention:

Axial force: 6.0 pounds minimum.

Radial torque: 4 inch-ounces minimum.

Solderability: In accordance with MIL-STD-202 (for quality conformance inspection, the test shall be

performed in group B following the insulation resistance test.)

Resistance to test probe damage: Not applicable.

Corrosion (salt spray): In accordance with test procedure EIA - 364-26.

Voltage standing wave ratio (VSWR): Not applicable.

Connector durability: In accordanc e with t est procedure EIA - 364-09, 500 cycles minimum at 12 cycles

per minute maximum. The connector shall meet mating characteristics and force to engage and

disengage requirements.

Contact resistance: In milliohms, maximum.

Initial After environment

Center contact: 3.0 4.0

Outer contact: 2.0 Not applicable

Source: http://assist.dla.mil -- Downloaded: 2021-04-29T16:43ZCheck the source to verify that this is the current version before use.

MIL-PRF-39012/60D

Dielec tric withs ta ndi ng volt age at sea le ve l: In accordance with test procedure EIA - 364-20, 1,000

Volts rms.

Vibration, high frequency: In accordance with tes t proc edur e EIA - 364-28, test condition IV.

Shock: In accordance with t est procedure EIA - 364-27, condition G.

Thermal shock: In accordance with test proc ed ur e EIA - 364-32, 5 cycles, except test high temperature

shall be +200°C.

Hum id it y: In accordanc e wi th test procedure EIA - 364-31. No measurements at high humidity.

Insulation resistance shall be at least 200 mega ohms within 5 minutes after removal from humidity.

Corona leve l:

Voltage: 250 volts minimum.

Altitude: 70,000 feet.

RF high potential withstanding voltage:

Voltage and frequency: 670 Volts rms at 5 MHz.

Leakage current: Not applicable.

Cable retention force: Not applicable.

Coupling mechanism retention force: Not applicable.

RF leakage: Not applicable.

RF insertion loss: Not applicable.

Group qualification: See table I.

Source: http://assist.dla.mil -- Downloaded: 2021-04-29T16:43ZCheck the source to verify that this is the current version before use.

MIL-PRF-39012/60D

TABLE I. Group qualification and retention testing.

Group

PINs 1/ 2/

I M39012/60-3001

M39012/60-3002

M39012/61-3001

M39012/61-3002

M39012/60-4001

M39012/60-4002

M39012/61-4001

M39012/61-4002

1/ Submission and qualification of any connector in

a group qualifies any and all conne ctors of the

entire group.

2/ For qualifi cat ion retention, data may be supplied

on any part in a group to retain qualification for that

entire group.

Changes from the previous issue. The margins of this specification are marked with vertical lines to

indicate where changes from the previous issue were made. This was done as a convenience only and

the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and

contractors are cautioned to evaluate the requirements of this document based on the entire content

irrespective of the marginal notations and relationship to the last previous issue.

Referenced documents. In addition to MIL-PRF-39012, this document references the following

documents:

MIL-STD-202

MIL-STD-348

ASTM B488

EIA - 364-09

EIA - 364-20

EIA - 364-21

EIA - 364-26

EIA - 364-27

EIA - 364-28

EIA - 364-31

EIA - 364-32

Source: http://assist.dla.mil -- Downloaded: 2021-04-29T16:43ZCheck the source to verify that this is the current version before use.

MIL-PRF-39012/60D

CONCLUDING MATERIAL

Custodians: Preparing activity:

Army - CR DLA - CC

Navy - EC

Air Force - 85 (Project 5935-2009-113)

DLA - CC

Revie w ac tivities :

Army - AM, AT, CR4, MI

Navy - AS, MC, O S, SH

Air Force - 19, 99

NOTE: The activities listed above were interested in this document as of the date of this document.

Since organizations and responsibilities can change, you should verify the currency of the information

above using the ASSIST Online database at https://assist.daps.dla.mil.

Source: http://assist.dla.mil -- Downloaded: 2021-04-29T16:43ZCheck the source to verify that this is the current version before use.