Si9113 Vishay Siliconix High-Voltage Current Mode PWM Controller for ISDN Power Supplies FEATURES D D D D D BiC/DMOS Technology Current Mode Control Max 50% Duty Cycle Operation 1.3-MHz Error Amp Up to 500-kHz Internal Oscillator D D D D D Soft-Start 0.6-V Fast Over-Current Protection <5-mA Supply Current for +VIN <18 V 23.5-V to 200-V Input Voltage Range Programmable Start/Stop Capability D Internal Start-Up Circuit D Power_Good Output DESCRIPTION Si9113 is a current mode PWM controller for ISDN power supplies. In a 14-pin SOIC package, it provides all necessary functions to implement a single-switch PWM with a minimum of external parts. To maximize the circuit integration, the Si9113 is designed with a 200-V depletion mode MOSFET capable of powering directly off the high input bus without an external start-up circuit. The Start and Stop input voltage thresholds can be programmed within the operating input voltage range by means of a resistor divider, provided +VIN (Start) > +VIN (Stop). The internal clock frequency is set with a single external resistor and is capable of capacitor-coupled external synchronization. In order to satisfy the stringent ambient temperature requirements, the Si9113 is rated to handle the industrial range of -40_C to 85_C. The Si9113 is available in both standard and lead (Pb)-free packages. FUNCTIONAL BLOCK DIAGRAM VIN (23.5 V to 200 V) VOUT Start-Up Drive Current Stop/Start Power_Good VREF = 1.3 V Comparator Fast Current Limit Comparator . See Detailed Block Diagram, page 7 Applications information see AN728. A Demonstration Borad data sheet is available for this product. Document Number: 71093 S-40746--Rev. B. 19-Apr-04 www.vishay.com 1 Si9113 Vishay Siliconix ABSOLUTE MAXIMUM RATINGS VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 V Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150_C VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Power Dissipation (Package)a 14-Pin SOIC (Y Suffix)b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900 mW Logic Inputs (OSC IN, OSC OUT, PWR_GOOD) . . . -0.3 V to VCC + 0.3 V or "10 mA Linear Inputs (FB, VREF, SENSE, SS) . . . . . . . . . . . . -0.3 V to VCC + 0.3 V Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 to 150_C Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40 to 85_C Thermal Impedance (QJA) 14-Pin SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140_C/W Notes a. Device mounted with all leads soldered or welded to PC board. b. Derate 7.2 mW/_C above 25_C. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING RANGE VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.5 V to 200 V VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V to 14 V Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to VCC Linear Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to VCC - 3 V FOSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 kHz to 500 kHz SPECIFICATIONSa Limits Test Conditions Unless Otherwise Specified p -40 to 85_C Symbol VCC = 10 V, +VIN = 48 V, ROSC = 390 kW Tempb Minc Typd Maxc Unit Output Voltage VREF OSCIN = - VIN (OSC Disabled) RL = 10 MW Room Full 1.275 1.26 1.3 1.3 1.325 1.34 V Short Circuit Current ISREF VREF = -VIN Room -25 -10 mA IREF = 0 to -0.5 mA Full "10 40 VCC = 10 to 14 V Full "2 5 VUVSTART Turn-On Full 8.10 8.8 9.50 VUVSTOP Turn-Off Full 8.10 8.8 9.50 Parameter Reference Load Regulation Line Regulation DVREF mV UVLO Under Voltage Lockout Input Bias Current ISTART ISTOP VSTOP = 8 V, V VSTART = 8 V Room 0.05 Room 0.05 Pre-Regulated VCC VREG Room 8.5 9.0 9.5 UVLO for VCC VCCUV Room 7.9 8.4 8.9 VREG - VCCUV VD Room 0.3 0.6 V mA V PWR_Good Comparator Rise Time trpg Fall Time tfpg Output Logic Low CPWR_Good PWR G d = 100 nF ISINK = 2.5 mA Room 35 Room 25 Room 0.4 mS mS 0.8 V Soft-Start SS Current ISS Room 11 mA Output Inhibit Voltage VSS Room 3.3 V Oscillator Maximum Frequencye fMAX Initial Accuracy fOSC Voltage Stability Df/f Temperature Coefficiente Maximum Duty Cycle www.vishay.com 2 ROSC = 0 Room ROSC = 390 k (Note f) Room 80 100 120 ROSC = 180 k (Note f) Room 160 200 240 Df/f = (f [14 V] - f [10 V]) / f [10 V] Room 10 15 % Full 450 650 ppm/_C fOSC = 100 kHz Room 50 TOSC DMAX 500 kHz % Document Number: 71093 S-40746--Rev. B. 19-Apr-04 Si9113 Vishay Siliconix SPECIFICATIONSa Limits Test Conditions Unless Otherwise Specified -40 to 85_C Symbol VCC = 10 V, +VIN = 48 V, ROSC = 390 kW Tempb Minc Typd Open Loop Voltage Gaine AVOL OSC IN = - VIN Room 50 60 Input BIAS Current IBIAS VFB = 1.3 V Room -1 VFB FB Tied to COMP, OSC IN = - VIN Full 1.28 Parameter Maxc Unit Error Amplifier Feedback Input Voltage Dynamic Output Impedancee ZOUT Room Unity Gain Bandwidthe BW Room Output Current IOUT Power Supply Rejectione 1 1 1.3 Source VFB = 0.8 V Room Sink VFB = 1.8 V Room 0.12 0.15 Room 50 70 0.5 PSRR dB 1 -5 mA 1.32 V 2 kW MHz -1 mA dB Current Limit Comparator Threshold Voltage VSOURCE VFB = 0 V Full td VSENSE = 0.85 V, See Figure 1 Full Output High Voltage VOH IOUT = -10 mA Room Full Output Low Voltage VOL IOUT = 10 mA Room Full Delay to Outpute 0.6 0.7 V 100 150 ns Output Drive Rise Time tr Fall Time tf CL = 500 pF (10% to 90%) 9.7 9.5 0.3 0.5 Room 40 75 Room 40 75 V ns Supply ICC VCC = 10 V, ROSC = 390 kW VUVUP vVIN v 200 V Full 1 1.4 IVIN Excluding I From Resistive Divider of Stop and Start Pins Room 75 100 IVIN +VIN v 18 V, VSTART (Pin 14) < 8.8 V Room 2 5 Supply Current Supply Current UVLO Mode mA mA Notes a. Refer to PROCESS OPTION FLOWCHART for additional information. b. Room = 25_C, Full = -40 to 85_C. c. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum. d. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. e. Guaranteed by design, not subject to production test. f. CSTRAY Pin 8 = v 5 pF. TIMING WAVEFORMS SENSE 0 VCC 0.85 V - 50% tr v 10 ns td 90% OUTPUT 0 - FIGURE 1. Delay Time for Current Sense Document Number: 71093 S-40746--Rev. B. 19-Apr-04 www.vishay.com 3 Si9113 Vishay Siliconix TYPICAL CHARACTERISTICS (25_C UNLESS NOTED) VREF vs. Temperature (VIN = 48 V) 1.306 1.302 VUVSTART /VUVSTOP (v) VREF - (V) 9.0 VCC = 14 V 1.304 VCC = 12 V VCC = 10 V 1.300 VUVSTART/VUVSTOP vs. Temperature 9.1 8.9 8.8 8.7 8.6 8.5 1.298 -50 -25 0 25 50 75 8.4 -50 100 -25 0 50 75 100 Temperature (_C) Temperature (_C) Output Frequency vs. Oscillator Resistance Supply Current vs. Output Frequency 2.0 300 1.6 VCC = 10 V VCC = 14 V I CC (mA) FOUT (kHz) 25 100 1.2 VCC = 10 V VCC = 12 V 0.8 0.4 0.0 10 10 100 1000 0 2000 50 100 FOSC (kW) Output Frequency vs. Supply Voltage 200 250 300 Soft-Start Current vs. Temperature 24 13 ROSC = 1 MW 12 22 85_C VCC = 10 V 11 25_C 20 -40_C I SS ( m A) FOUT (kHz) 150 FOUT (kHz) 18 10 9 16 8 14 9 10 11 12 VCC (V) www.vishay.com 4 13 14 15 7 -40 -20 0 20 40 60 80 100 Temperature (_C) Document Number: 71093 S-40746--Rev. B. 19-Apr-04 Si9113 Vishay Siliconix TYPICAL CHARACTERISTICS (25_C UNLESS NOTED) UVLO Supply Current vs. VIN 10 Output Rise Time vs. Load 80 VCC = 10 V 60 Rise/Fall Time (nS) I IN ( (mA) 85_C 1 25_C 40 20 -40_C 0 0.1 11 13 15 17 19 0 21 200 VIN (V) 400 600 800 COUT (pF) Efficiency vs. Output Power 90 VIN = 28 V 80 Efficiency (%) 70 VIN = 48 V 60 VIN = 99 V 50 40 30 20 10 0 200 400 600 800 1000 WO (mW) Document Number: 71093 S-40746--Rev. B. 19-Apr-04 www.vishay.com 5 Si9113 Vishay Siliconix PIN CONFIGURATION SOIC-14 STOP 1 14 START VIN 2 13 COMP SENSE 3 PWR_GOOD 4 -VIN 12 FB ORDERING INFORMATION Part Number 11 VREF Si9113DY 5 10 SS Si9113DY-T1 DRIVER 6 9 OSCOUT VCC 7 8 OSCIN Si9113 Temperature Range Bulk -40 to 85_C Tape and Reel Si9113DY-T1--E3 Top View Package Eval Kit Temperature Range Board Type -10 10 to 70_C Surface Mount and Thru-Hole Si9113D1 Si9113D2 PIN DESCRIPTION Pin Number Name 1 STOP 2 +VIN 3 SENSE 4 PWR_GOOD 5 -VIN 6 DRIVER 7 VCC 8 OSCIN 9 OSCOUT 10 SS 11 VREF 12 FB Set up the stop threshold of +VIN for VCC via resistive dividers Input voltage to UVLO and Start-Up circuitry Current sense amplifier input for current mode control and OCP. Logic high PWR_Good signal indicates FB voltage is within regulation. Ground pin MOSFET gate drive signal. Supply voltage to internal circuitry and MOSFET gate drive. ROSC terminal ROSC terminal, square waveform output Soft-Start, time programmed by capacitor value. 1.3-V reference. Decoupled with 0.1-mF capacitor. Inverting input of an error amplifier. 13 COMP Error amplifier output for external compensation network. 14 START Set up the start threshold of +VIN for VCC via resistive dividers www.vishay.com 6 Function Document Number: 71093 S-40746--Rev. B. 19-Apr-04 Si9113 Vishay Siliconix DETAILED BLOCK DIAGRAM 8 COMP 13 9 VCC OSCIN OSCOUT OSC PWR_GOOD FB VREF 4 Error Amplifier 12 - 11 Clock (1/2 fOSC) 3.6 V + - + - PWM Comparator R + Q MOS Driver S SS 6 + Ref Gen - 10 C/L Comparator 5 VIN STOP START -VIN 0.6 V 3 VCC DRIVER SENSE 7 2 1 14 Programmable Start/Stop Circuit Enable Start-Up Pre-Regulator DETAILED DESCRIPTION Start-Up The Si9113 start-up circuit prevents the internal circuits from turning on until the voltage on the +VIN pin, via the resistor divider R3, R4, R5, is sufficiently positive such that the voltage across R3 (VSTART) is >8.8 V (typical value for the internal reference VUVSTART [see Figure 2]). When this occurs, the internal 1.3-V reference, soft-start and oscillator circuits are enabled. A constant current source provides the current to the external soft-start capacitor, which allows the output voltage to rise gradually without overshoot. The output drive circuit is disabled until the soft-start voltage reaches 3.3 V. The controller is continuously powered in the state until the VIN voltage falls and VSTOP drops below 8.8 V (the typical value for Document Number: 71093 S-40746--Rev. B. 19-Apr-04 the internal reference VUVSTOP). The user can program the +VIN START and +VIN STOP voltage with the external resistor divider R3-R5 (see Figure 2) as follows: VIN(START) + VIN(STOP) + R3 ) R4 ) R5 R5 R3 ) R5 R5 VUVSTART VUVSTOP (1) (2) Since VUVSTART = VUVSTOP = 8.8 V (typical) the hysteresis voltage can be expressed as: www.vishay.com 7 Si9113 Vishay Siliconix DVIN + R4 R5 VUVSTART (3) VCC Circuit The depletion MOSFET process allows the Si9113 controller to power directly from the high input bus voltage. Once VUVSTART is met, the pre-regulator start-up circuit generates the 9.0-V VCC voltage. The VCC voltage is used internally to power the IC as well as providing the drive current for the external MOSFET. An internal VCC circuit is disabled once a higher external voltage (X10 V) is applied to this pin. If VCC is below VCCUV, the Si9113 will inhibit the driver output switching. period eliminating any chance of undesirable noise frequency. When the output load current decreases to 0 A, the controller is forced to enter the pulse skipping mode. This is a natural phenomenal for all controllers since the duty cycle cannot decrease linearly to 0%. Error Amplifier The reference voltage of Si9113 is set at 1.3 V. The reference voltage is internally connected to the non-inverting input of error amplifier. The reference is decoupled with 0.1-mF capacitor. The error amplifier gain-bandwidth product and slew rate are critical parameters which determine the transient response of converter. The transient response is the function of both small and large signal responses. The small signal response is determined by the converter closed loop bandwidth and phase margin while the large signal is determined by the error amplifier dv/dt and the inductor di/dt slew rate. Besides the inductance value, the error amplifier determines the converter response time. In order to minimize the response time, the Si9113 is designed with 1.3-MHz error amplifier gain-bandwidth product to generate the widest converter bandwidth. Soft-Start Current Limit The soft-start circuit provides a constant 10-mA current to external capacitor attached to SS pin. A constant soft-start current forces a gradual increase in duty cycle which in turn ensures gradual output voltage rise without overshooting. The soft-start time is programmed by the capacitance value. Over current protection circuit is provided by monitoring the voltage on the Sense pin. Once the current sense voltage reaches 0.6V peak, the output drive stage is disabled for the remainder of the clock cycle. REF Power_Good Comparator Oscillator The oscillator consists of a ring of CMOS inverters, capacitors, and a capacitor discharge switch. An external resistor, ROSC, between the OSCIN and OSCOUT pins sets the frequency. The maximum frequency is obtained when ROSC = 0 W. A frequency divider in the logic section limits the switch duty cycle to 50% by locking the switching frequency to one-half of the oscillator frequency. The PWR_Good signal indicates the status of output voltage. If the output voltage and VCC are within regulation, the PWR_Good signal generates a logic high output by monitoring the voltage on COMP and VCC pins. If either one is out of regulation, a logic low PWR_Good signal is generated. The capacitor at the PWR_Good pin determines the rise time of the power good signal, once all the conditions are met for power good. The PWR_Good signal is an open collector output capable of sinking 2.5 mA. PWM Mode As the load and line voltage vary, the switching frequency remains constant. The switching frequency is programmed by the ROSC value as shown by the oscillator curve. In the PWM mode, a duty cycle pulse is generated for each switching www.vishay.com 8 MOSFET Gate Drive The DRIVER pin is designed to drive the low-side n-channel MOSFET. Typically, the driver stage is sized to sink and source 200-mA of peak current when VCC = 12 V. Document Number: 71093 S-40746--Rev. B. 19-Apr-04 Si9113 Vishay Siliconix TYPICAL APPLICATION CIRCUITS 28 - 99 V +VIN 4 3 -VIN T1 XFMR_EPC17 BR1 AC + AC - + C1 22 mF 160 V 2 DF02S ESIG C4 1 mF R13 D1 2.7 W ESIG 3.3 V C10 220 mF 10 V C10 NS2 2.2 mF 50 V 3 6 7 D3 C12 0.1 mF C5 0.1 mF R9 20 kW NS3 9 3 + D4* BZX84C43 1 COM2 NP 5 B130LB 8 COM1 R1 R10 13 kW 40 V D2 1 1 1 MW C7 8 7 OSCIN 9 10 OSCOUT DR 11 0.1 mF 12 13 14 R2 C8 300 kW 0.01 mF R5 3.96 MW 3 VREF PWR_G FB ICS COMP VIN START STOP Q01 Si3420DV 4 GND Si9113 C3 100 pF 6 5 SS 0.001 mF C6 1, 2, 5, 6 VCC 4 3 R11 2 1 kW C9 220 pF 1 R7 2W 1/ W 2 R3 5.1 MW R4 1 MW *Optional FIGURE 2. Dual Output Flyback Converter with 2% Regulation for 3.3 V ( As used on Demo Board--DB1) Document Number: 71093 S-40746--Rev. B. 19-Apr-04 www.vishay.com 9 Si9113 Vishay Siliconix TYPICAL APPLICATION CIRCUITS 28 - 99 V +VIN 4 3 -VIN T1 XFMR_EPC17 BR1 AC + AC - + C1 22 mF 160 V 2 DF02S 40 V D2 4 1 ESIG R13 2.7 W R9 89 kW R10 C4 1 mF D1 5 ESIG 8 NP 1 MW C7 8 7 OSCIN 9 10 VCC OSCOUT DR B130LB NS1 1 6 C11 220 mF 10 V 11 0.1 mF 12 13 14 R2 C8 300 kW 0.01 mF PWR_G FB ICS COMP VIN START STOP Si9113 C3 100 pF R5 3.96 MW C5 0.1 mF C12 0.1 mF 1, 2, 5, 6 3 Q01 Si3420DV 4 GND VREF + COM1 5 SS 0.001 mF C6 6 D4* BZX84C43 COM2 1 3.3 V 12.7 kW R1 + D3 2 9 NS3 3 C10 NS2 2.2 mF 50 V 3 4 3 R11 2 1 kW C9 470 pF 1 R7 2W 1/ W 2 R3 5.1 MW R4 1 MW *Optional FIGURE 3. Dual Output Flyback Converter with Moderately Regulated Outputs (As used on Demo Board DB-2) www.vishay.com 10 Document Number: 71093 S-40746--Rev. B. 19-Apr-04 Legal Disclaimer Notice Vishay Notice Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Document Number: 91000 Revision: 08-Apr-05 www.vishay.com 1 Package Information Vishay Siliconix SOIC (NARROW): 14-LEAD (POWER IC ONLY) MILLIMETERS 14 13 12 11 10 9 Dim A A1 B C D E e H L O 8 E 2 3 4 5 6 7 D A e B Document Number: 72809 28-Jan-04 A1 0.25 (GAGE PLANE) 1 H INCHES Min Max Min Max 1.35 1.75 0.053 0.069 0.10 0.20 0.004 0.008 0.38 0.51 0.015 0.020 0.18 0.23 0.007 0.009 8.55 8.75 0.336 0.344 3.8 4.00 0.149 0.157 1.27 BSC 0.050 BSC 5.80 6.20 0.228 0.244 0.50 0.93 0.020 0.037 0_ 8_ 0_ 8_ ECN: S-40080--Rev. A, 02-Feb-04 DWG: 5914 C ALL LEADS L O 0.101 mm 0.004 www.vishay.com 1 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000