COMPACT AND POWERFUL WIRED AND WIRELESS EMBEDDED MODULES DIGI CONNECT ME 9210 FAMILY Ultra-compact high-performance embedded modules for M2M networking combine on-chip security and integrated 802.11b/g/n Wi-Fi or Ethernet networking DIGI CONNECT(R) WI-ME 9210 RJ-45 w/Integrated Magnetics RP-SMA Antenna Connector PHY 8 MB FLASH 16 MB SDRAM I2C ARM DRPIC165X FIM ARM926EJ-S 75 MHz Mem Ctrlr UART Power Mgmt 802.11bgn Wi-Fi Radio SPI JTAG The Digi Connect ME 9210 family features the development and operational benefits of Digi Remote Manager (R). This secure, highly-scalable platform seamlessly ties enterprise applications and remote devices together. Using Digi Remote Manager, customers can also easily configure, upgrade, monitor and troubleshoot their devices from a centralized location. DIGI CONNECT ME(R) 9210 AES Accelerator These modules can provide future application-specific interface options through the programmable Flexible Interface Module (FIM), while keeping the main serial port or other key peripheral interfaces available. They are well-suited for more advanced core module applications by supporting up to ten shared GPIOs, external IRQs and an extended set of peripheral interface options. BLOCK DIAGRAM 10 /100 Ethernet MAC The Digi Connect ME 9210 family of embedded modules enables secure wired and wireless networking. Built on Digi's powerful NS9210 ARM9 processor, these high-performance modules allow customers to implement next generation network-enabled products. Additionally, their RJ-45 form factor is pin compatible with modules in the Digi Connect ME family. GPIO BENEFITS - Secure 802.11b/g/n Wi-Fi support 20-Pin Connector - Integrated 10/100 Mbit Ethernet interface JTAG Connector - Support for Digi Embedded Linux and Digi NET+OS - Industrial operating temperature System-on-Module - RJ-45 form factor compatible with Digi Connect ME - On-chip hardware encryption engine - Extended set of on-chip interfaces and signals RELATED PRODUCTS - Power management modes - Low-emission design (FCC Class B) Digi Connect(R) ME ConnectCore(R) 9P 9215 ConnectCardTM for i.MX28 Digi XBee(R) Development Kits DIGI JUMPSTART KIT(R) OVERVIEW DIGI JUMPSTART KIT(R) FOR NET+OS DIGI JUMPSTART KIT(R) FOR EMBEDDED LINUX This royalty-free turnkey solution for embedded software development is based on the ThreadX Real-Time Operating System (RTOS), one of the most reliable and field-proven RTOS solutions available. In addition to ThreadX, NET+OS(R) provides the integrated building blocks needed to create product solutions with leading network security using Digi embedded modules and microprocessors. Built around a standard Linux 2.6 kernel distribution, the Digi JumpStart Kit for Embedded Linux is tailored to the specific needs of embedded Linux development and provides an easy-to-use, complete off-the-shelf embedded development platform. It includes all components that are required to build secure network-enabled products based on the Digi Connect ME 9210 family. For professional NET+OS software development, the Eclipse based Digi ESPTM Integrated Development Environment (IDE) with graphical user interface and high-speed USB 2.0 hardware debugger is provided out-of-the-box. The kit includes Digi ESPTM for Embedded Linux, a powerful and fully Linux-hosted Integrated Development Environment based on the open EclipseTM framework. Ideal for new and experienced Linux developers, Digi ESP improves software design productivity by accelerating and greatly simplifying driver and application development through a user-friendly graphical interface. * * * * Royalty-free turnkey solution for embedded software development Built on field-proven and compact ThreadX RTOS Fully integrated support for secure, IPv4/IPv6 networking applications Professional software development using Windows-based Digi ESP IDE * * * * Off-the-shelf development platform for network-enabled embedded systems Royalty-free and with optimized 2.6 kernel and services support Linux Digi ESP IDE for accelerated software development Full Linux and Digi BSP source code included SOFTWARE PLATFORM NET+OS(R) EMBEDDED LINUX MODULE Digi Connect ME 9210 or Digi Connect Wi-ME 9210 w/ 8 MB Flash, 16 MB SDRAM DEVELOPMENT BOARD 1 RS-232 serial port, GPIO configuration switches, screw terminal for GPIO signals, prototyping area, status LEDs (serial, GPIO, power), logic signal header, test points, reset button, user/wake-up buttons, PoE module header, 9-30 VDC power supply, JTAG header and RS-232 console/debug port for JTAG-equipped modules CD/DVD Digi NET+OS CD: NET+OS 7, Digi ESP IDE, BSP source code, sample code, Green Hills MULTI IDE support files, user documentation Digi Embedded Linux 4 DVD: Digi Embedded Linux, Digi ESP IDE, Linux and platform specific source code, Universal boot loader source code (U-Boot), sample code, documentation DOCUMENTATION Quick start guide, Digi ESP tutorial, NET+OS porting guide, NET+OS API documentation, Advanced Web Server, hardware reference manual, development board schematics Quick start guide, Digi Embedded Linux user's guide, hardware reference manual, development board schematics POWER SUPPLIES AND ACCESSORIES External wall power supply (110/240 VAC) with interchangeable outlet adapters (North America, EU, UK, and Australia), crossover serial cable, Ethernet cable OTHER Digi JTAG Link USB 2.0 hardware debugger N/A Please refer to the feature specs on our website for detailed information about the specific software platform capabilities. WWW.DIGI.COM SPECIFICATIONS Digi Connect ME(R) 9210 | Digi Connect Wi-ME(R) 9210 HARDWARE PROCESSOR TYPE 32-bit Digi NS9210 processor ARM CORE ARM926EJ-S PROCESSOR SPEED 75 MHz CACHE 4k I/D Cache MEMORY BASE POPULATION Support up to 8 MB NOR Flash; Support up to 16 MB SDRAM FLEXIBLE INTERFACE MODULES (FIMS) 300 MHz DRPIC165X CPU; 2k program/192 bytes data RAM ON-CHIP 256-BIT AES ACCELERATOR Yes POWER MANAGEMENT MODES On-the-fly clock scaling; Low-power sleep modes; Configurable scaling/wake-up events (EIRQ, UART, Ethernet, etc.) PINS/FORM FACTOR RJ-45 connector style with 20-pin micro pin header (Samtec FTS-110-01-F-DV-TR) HIGH-SPEED TTL SERIAL INTERFACE Full signal support (TXD, RXD, RTS, CTS, DTR, DSR and DCD); Hardware/Software flow control GPIO 10 shared; Up to 3 external IRQ options SPI Master data rate up to 16.7 Mbps; Slave data rate up to 7.5 Mbps IC v1.0 bus interface; 7-bit and 10-bit address modes FLEXIBLE INTERFACE SUPPORT (FIM) UART, 1-Wire, USB device (low-speed), CAN BUS WATCHDOG TIMER (16-BIT) Yes JTAG INTERFACE Available on development modules only ON-BOARD POWER SUPERVISOR Yes WAVE-SOLDERABLE DESIGN No clean flux process DIMENSIONS (L X W X H) 1.445 in (36.7 mm) x 0.75 in (19.05 mm) x 0.735 in (18.67 mm) 2 NETWORK INTERFACE - WIRED PHYSICAL LAYER 10/100Base-T N/A DATA RATE 10/100 Mbps (auto-sensing) N/A MODE Full- or half-duplex (auto-sensing) N/A CONNECTOR RJ-45 w/ magnetics N/A POE POWER PASS-THROUGH 802.3af compliant (Mid- and End-span) N/A STANDARD N/A IEEE 802.11b/g/n FREQUENCY N/A 2.4 GHz DATA RATE N/A Up to 65 Mbps with automatic fallback MODULATION N/A CCK (11/5 Mbps), DQPSK (2 Mbps), DBPSK (1 Mbps), OFDM (6, 9, 12, 18, 24, 48, 54 and 65 Mbps) TYPICAL TRANSMIT POWER N/A +17 dBm RECEIVE SENSITIVITY N/A -69 dBm @ 54 Mbps CONNECTOR N/A 1 x RP-SMA NETWORK INTERFACE - WIRELESS LAN WLAN SECURITY WEP (WIRED EQUIVALENT PRIVACY) WPA/WPA2/802.11I N/A 64/128-bit encryption (RC4) N/A 128-bit TKIP/CCMP (AES) encryption. Enterprise mode (802.1X): LEAP (WEP only), PEAP, TTLS, TLS, EAP-FAST, GTC, MD5, OTP, PAP, CHAP, MSCHAP, MSCHAPv2, TTLS-MSCHAPv2. Pre-shared key mode (PSK/Personal). ENVIRONMENTAL OPERATING TEMPERATURE -40 C to +75 C (-40 F to +167 F) -40 C to +85 C (-40 F to +185 F) with external thermal pad* STORAGE TEMPERATURE -50 C to +125 C (-58 F to +257 F) RELATIVE HUMIDITY 5% to 90% (non-condensing) ALTITUDE 12,000 feet (3,658 meters) POWER REQUIREMENTS (3.3 VDC) MAXIMUM 450 mA (1.485 W) TYPICAL 346 mA (1.14 W) UART and Ethernet activated IDLE 186 mA (613 mW)/16 clock scaling, Ethernet activated - SLEEP 3.3 VDC @ 34 mA (113 mW) 3.3 VDC @ 142 mA (486 mW) WARRANTY PRODUCT WARRANTY 3 years *Please see hardware reference manual for detailed information WWW.DIGI.COM Digi Connect ME(R) 9210 SPECIFICATIONS | Digi Connect Wi-ME(R) 9210 REGULATORY APPROVALS FCC PART 15 CLASS B, EN 55022 CLASS B EN 61000-3-2 AND EN 61000-3-3 ICES-003 CLASS B, VCCI CLASS II, AS 3548 FCC PART 15 SUB C SECTION 15.247 IC RSS-210 ISSUE 5 SECTION 6.2.2(O) EN 300 328, EN 301 489-17 UL 60950-1, EN 60950 (EU) CSA C22.2, NO. 60950 EN 55024 INTENTIONAL RADIATION Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes MODULE PINOUT PIN UART GPIO RECOMMENDED PCB LAYOUT EXT IRQ I2C SPI FIM OTHER 1 VETH+ 2 VETH- 3-6 Positions removed 7 RxD GPIO[3] IN 8 TxD GPIO[7] OUT Timer Out 7 Timer In 8 GPIO[5] CLK Timer Out 6 9 RTS 10 DTR GPIO[6] 11 CTS GPIO[1] 0 1 12 DSR GPIO[2] 13 DCD GPIO[0] 3 PIC[3] Timer In 7 PIC[1] PIC[2] EN PIC[0] 14 /RST 15 3.3V 16 GND 17 GPIO[12] 18 GPIO[9] 19 20 SDA 0 CLK RESET_DONE CLK INIT Timer Out 9 SCL Reserved GPIO[13] PART NUMBERS DESCRIPTION DIGI JUMPSTART KITS DC-WME-9210-LX Digi Connect Wi-ME 9210 Digi JumpStart Kit for Digi Embedded Linux DC-ME-9210-LX Digi Connect ME 9210 Digi JumpStart Kit for Digi Embedded Linux DC-WME-9210-NET Digi Connect Wi-ME 9210 Digi JumpStart Kit for NET+OS 7 DC-ME-9210-NET Digi Connect ME 9210 Digi JumpStart Kit for NET+OS 7 DIGI CONNECT ME MODULES DC-ME-Y402-S Digi Connect ME 9210 w/4 MB Flash, 8 MB RAM (single-unit pack) DC-ME-Y402-LX Digi Connect ME 9210 w/4 MB Flash, 8 MB RAM (single-unit pack) DC-ME-Y413-LX Digi Connect ME 9210 w/16MB SDRAM, 8 MB Flash, for Digi Embedded Linux, Single Pack DC-ME-Y401-C Digi Connect ME 9210 w/2 MB Flash, 8 MB RAM (single-unit pack) DC-ME-Y402-C Digi Connect ME 9210 w/4 MB Flash, 8 MB RAM (single-unit pack) DIGI CONNECT WI-ME MODULES DC-WME-Y413-LX Connect Wi-ME 9210 8/16 Linux DC-WME-Y402-C Connect Wi-ME 9210 4/8 NET+OS DIGI SERVICE AND SUPPORT / You can purchase with confidence knowing that Digi is always available to serve you with expert technical support and our industry leading warranty. For detailed information visit www.digi.com/support. (c) 1996-2019 Digi International Inc. All rights reserved. All trademarks are the property of their respective owners. 91001478 E6/519 DIGI INTERNATIONAL WORLDWIDE HQ 877-912-3444 / 952-912-3444 / www.digi.com DIGI INTERNATIONAL SINGAPORE +65-6213-5380 DIGI INTERNATIONAL GERMANY +49-89-540-428-0 DIGI INTERNATIONAL CHINA +86-21-50492199 / www.digi.com.cn DIGI INTERNATIONAL JAPAN +81-3-5428-0261 / www.digi-intl.co.jp