LMH6715 LMH6715 Dual Wideband Video Op Amp Literature Number: SNOSA10B LMH6715 Dual Wideband Video Op Amp General Description Features The LMH6715 combines National's VIP10TM high speed complementary bipolar process with National's current feedback topology to produce a very high speed dual op amp. The LMH6715 provides 400MHz small signal bandwidth at a gain of +2V/V and 1300V/s slew rate while consuming only 5.8mA per amplifier from 5V supplies. TA = 25C, RL = 100, typical values unless specified. n Very low diff. gain, phase: 0.02%, 0.02 n Wide bandwidth: 480MHz (AV = +1V/V); 400MHz (AV = +2V/V) n 0.1dB gain flatness to 100MHz n Low power: 5.8mA/channel n -70dB channel-to-channel crosstalk (10MHz) n Fast slew rate: 1300V/s n Unity gain stable n Improved replacement for CLC412 The LMH6715 offers exceptional video performance with its 0.02% and 0.02 differential gain and phase errors for NTSC and PAL video signals while driving up to four back terminated 75 loads. The LMH6715 also offers a flat gain response of 0.1dB to 100MHz and very low channel-tochannel crosstalk of -70dB at 10MHz. Additionally, each amplifier can deliver 70mA of output current. This level of performance makes the LMH6715 an ideal dual op amp for high density, broadcast quality video systems. The LMH6715's two very well matched amplifiers support a number of applications such as differential line drivers and receivers. In addition, the LMH6715 is well suited for Sallen Key active filters in applications such as anti-aliasing filters for high speed A/D converters. Its small 8-pin SOIC package, low power requirement, low noise and distortion allow the LMH6715 to serve portable RF applications such as IQ channels. Differential Gain & Phase with Multiple Video Loads Applications n n n n n n HDTV, NTSC & PAL video systems Video switching and distribution IQ amplifiers Wideband active filters Cable drivers DC coupled single-to-differential conversions Frequency Response vs. VOUT 20042916 20042908 (c) 2003 National Semiconductor Corporation DS200429 www.national.com LMH6715 Dual Wideband Video Op Amp January 2003 LMH6715 Absolute Maximum Ratings Storage Temperature Range (Note 1) -65C to +150C Lead Temperature (Soldering 10 sec) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 4) +300C Operating Ratings Human Body Model 2000V Machine Model Thermal Resistance 150V VCC 6.75V IOUT (Note 3) Package SOIC Differential Input Voltage 145C/W -40C to +85C 5V to 6V Nominal Operating Voltage 2.2V Maximum Junction Temperature (JA) 65C/W Operating Temperature Range VCC Common-Mode Input Voltage (JC) +150C Electrical Characteristics AV = +2, RF = 500, VCC = 5 V, RL = 100; unless otherwise specified. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Response SSBW -3dB Bandwidth VOUT < 0.5VPP, RF = 300 LSBW -3dB Bandwidth VOUT < 4.0VPP, RF = 300 Gain Flatness VOUT < 0.5VPP GFP Peaking GFR Rolloff 280 DC to 100MHz, RF = 300 400 MHz 170 MHz 0.1 dB DC to 100MHz, RF = 300 0.1 dB LPD Linear Phase Deviation DC to 100MHz, RF = 300 0.25 deg DG Differential Gain RL = 150, 4.43MHz 0.02 % DP Differential Phase RL = 150, 4.43MHz 0.02 deg 1.4 ns Time Domain Response Tr Rise and Fall Time 0.5V Step 4V Step 3 ns Ts Settling Time to 0.05% 2V Step 12 ns OS Overshoot 0.5V Step 1 % SR Slew Rate 2V Step 1300 V/s Distortion And Noise Response HD2 2nd Harmonic Distortion 2VPP, 20MHz -60 dBc HD3 3rd Harmonic Distortion 2VPP, 20MHz -75 dBc Equivalent Input Noise VN Non-Inverting Voltage IN Inverting Current INN Non-Inverting Current SNF XTLKA Noise Floor Crosstalk > 1MHz > 1MHz > 1MHz > 1MHz -153 dB1Hz Input Referred 10MHz -70 dB 3.4 nV/ 10.0 pA/ 1.4 pA/ Static, DC Performance VIO DVIO IBN 30 5 Inverting 30 6 Average Drift Input Bias Current DIBI PSRR Non-Inverting Average Drift Input Bias Current DIBN IBI 2 Input Offset Voltage Average Drift Power Supply Rejection Ratio www.national.com DC 46 44 2 6 8 mV V/C 12 20 A nA/C 21 35 A 20 nA/C 60 dB (Continued) AV = +2, RF = 500, VCC = 5 V, RL = 100; unless otherwise specified. Boldface limits apply at the temperature extremes. Min Typ CMRR Symbol Common Mode Rejection Ratio Parameter DC Conditions 50 47 56 ICC Supply Current per Amplifier RL = 4.7 4.1 5.8 Max Units dB 7.6 8.1 mA Miscellaneous Performance RIN Input Resistance Non-Inverting 1000 k CIN Input Capacitance Non-Inverting 1.0 pF ROUT Output Resistance Closed Loop .06 VO Output Voltage Range RL = 4.0 3.9 V VOL 3.5 3.4 RL = 100 CMIR Input Voltage Range IO Output Current Common Mode V 2.2 V 70 mA Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications, see the Electrical Characteristics tables. Note 2: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where TJ > TA. See Applications Section for information on temperature de-rating of this device." Min/Max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Note 3: The maximum output current (IOUT) is determined by device power dissipation limitations. See the Power Dissipation section of the Application Division for more details. Note 4: Human body model, 1.5k in series with 100pF. Machine model, 0 In series with 200pF. Connection Diagram 8-Pin SOIC 20042904 Top View Ordering Information Package 8-pin SOIC Part Number LMH6715MA LMH6715MAX Package Marking Transport Media Rails LMH6715MA 2.5k Units Tape and Reel 3 NSC Drawing M08A www.national.com LMH6715 Electrical Characteristics LMH6715 Typical Performance Characteristics (TA = 25C, VCC = 5V, AV = 2V/V, RF = 500, RL = 100, unless otherwise specified). Non-Inverting Frequency Response Inverting Frequency Response 20042913 20042912 Non-Inverting Frequency Response vs. VOUT Small Signal Channel Matching 20042916 20042901 Frequency Response vs. Load Resistance Non-Inverting Frequency Response vs. RF 20042915 www.national.com 20042914 4 Small Signal Pulse Response Large Signal Pulse Response 20042918 20042919 Input-Referred Crosstalk Settling Time vs. Accuracy 20042907 20042924 -3dB Bandwidth vs. VOUT DC Errors vs. Temperature 20042926 20042925 5 www.national.com LMH6715 Typical Performance Characteristics (TA = 25C, VCC = 5V, AV = 2V/V, RF = 500, RL = 100, unless otherwise specified). (Continued) LMH6715 Typical Performance Characteristics (TA = 25C, VCC = 5V, AV = 2V/V, RF = 500, RL = 100, unless otherwise specified). (Continued) Open Loop Transimpedance, Z(s) Equivalent Input Noise vs. Frequency 20042920 20042923 Differential Gain & Phase vs. Load Differential Gain vs. Frequency 20042909 20042908 Differential Phase vs. Frequency Gain Flatness & Linear Phase Deviation 20042910 www.national.com 20042911 6 2nd Harmonic Distortion vs. Output Voltage 3rd Harmonic Distortion vs. Output Voltage 20042902 20042905 Closed Loop Output Resistance PSRR & CMRR 20042906 20042917 Suggested RS vs. CL 20042927 7 www.national.com LMH6715 Typical Performance Characteristics (TA = 25C, VCC = 5V, AV = 2V/V, RF = 500, RL = 100, unless otherwise specified). (Continued) LMH6715 FEEDBACK RESISTOR SELECTION One of the key benefits of a current feedback operational amplifier is the ability to maintain optimum frequency response independent of gain by using appropriate values for the feedback resistor (RF). The Electrical Characteristics and Typical Performance plots specify an RF of 500, a gain of +2V/V and 5V power supplies (unless otherwise specified). Generally, lowering RF from it's recommended value will peak the frequency response and extend the bandwidth while increasing the value of RF will cause the frequency response to roll off faster. Reducing the value of RF too far below it's recommended value will cause overshoot, ringing and, eventually, oscillation. Application Section Frequency Response vs. RF 20042935 FIGURE 1. Non-Inverting Configuration with Power Supply Bypassing 20042914 The plot labeled "Frequency Response vs. RF" shows the LMH6715's frequency response as RF is varied (RL = 100, AV = +2). This plot shows that an RF of 200 results in peaking and marginal stability. An RF of 300 gives near maximal bandwidth and gain flatness with good stability, but with very light loads (RL > 300) the device may show some peaking. An RF of 500 gives excellent stability with good bandwidth and is the recommended value for most applications. Since all applications are slightly different it is worth some experimentation to find the optimal RF for a given circuit. For more information see Application Note OA-13 which describes the relationship between RF and closedloop frequency response for current feedback operational amplifiers. When configuring the LMH6715 for gains other than +2V/V, it is usually necessary to adjust the value of the feedback resistor. The two plots labeled "RF vs. Non-inverting Gain" and "RF vs. Inverting Gain" provide recommended feedback resistor values for a number of gain selections. 20042937 FIGURE 2. Inverting Configuration with Power Supply Bypassing Application Introduction Offered in an 8-pin package for reduced space and cost, the wideband LMH6715 dual current-feedback op amp provides closely matched DC and AC electrical performance characteristics making the part an ideal choice for wideband signal processing. Applications such as broadcast quality video systems, IQ amplifiers, filter blocks, high speed peak detectors, integrators and transimedance amplifiers will all find superior performance in the LMH6715 dual op amp. www.national.com 8 tances (to AC ground) arising from traces or pads placed too closely ( < 0.1") to power or ground planes. In some cases, due to the frequency response peaking caused by these parasitics, a small adjustment of the feedback resistor value will serve to compensate the frequency response. Also, it is very important to keep the parasitic capacitance across the feedback resistor to an absolute minimum. (Continued) RF vs. Non-Inverting Gain The performance plots in the data sheet can be reproduced using the evaluation boards available from National. The CLC730036 board uses all SMT parts for the evaluation of the LMH6715. The board can serve as an example layout for the final production printed circuit board. Care must also be taken with the LMH6715's layout in order to achieve the best circuit performance, particularly channelto-channel isolation. The decoupling capacitors (both tantalum and ceramic) must be chosen with good high frequency characteristics to decouple the power supplies and the physical placement of the LMH6715's external components is critical. Grouping each amplifier's external components with their own ground connection and separating them from the external components of the opposing channel with the maximum possible distance is recommended. The input (RIN) and gain setting resistors (RF) are the most critical. It is also recommended that the ceramic decoupling capacitor (0.1F chip or radial-leaded with low ESR) should be placed as closely to the power pins as possible. 20042921 Both plots show the value of RF approaching a minimum value (dashed line) at high gains. Reducing the feedback resistor below this value will result in instability and possibly oscillation. The recommended value of RF is depicted by the solid line, which begins to increase at higher gains. The reason that a higher RF is required at higher gains is the need to keep RG from decreasing too far below the output impedance of the input buffer. For the LMH6715 the output resistance of the input buffer is approximately 160 and 50 is a practical lower limit for RG. Due to the limitations on RG the LMH6715 begins to operate in a gain bandwidth limited fashion for gains of 5V/V or greater. POWER DISSIPATION Follow these steps to determine the Maximum power dissipation for the LMH6715: 1. Calculate the quiescent (no-load) power: PAMP = ICC (VCC - VEE) 2. Calculate the RMS power at the output stage: PO = (VCC -VLOAD)(ILOAD), where VLOAD and ILOAD are the voltage and current across the external load. 3. Calculate the total RMS power: Pt = PAMP + PO RF vs. Inverting Gain The maximum power that the LMH6715, package can dissipate at a given temperature can be derived with the following equation: Pmax = (150o - Tamb)/ JA, where Tamb = Ambient temperature (C) and JA = Thermal resistance, from junction to ambient, for a given package (C/W). For the SOIC package JA is 145C/W. MATCHING PERFORMANCE With proper board layout, the AC performance match between the two LMH6715's amplifiers can be tightly controlled as shown in Typical Performance plot labeled "Small-Signal Channel Matching". The measurements were performed with SMT components using a feedback resistor of 300 at a gain of +2V/V. The LMH6715's amplifiers, built on the same die, provide the advantage of having tightly matched DC characteristics. 20042922 When using the LMH6715 as a replacement for the CLC412, identical bandwidth can be obtained by using an appropriate value of RF . The chart "Frequency Response vs. RF" shows that an RF of approximately 700 will provide bandwidth very close to that of the CLC412. At other gains a similar increase in RF can be used to match the new and old parts. SLEW RATE AND SETTLING TIME One of the advantages of current-feedback topology is an inherently high slew rate which produces a wider full power bandwidth. The LMH6715 has a typical slew rate of 1300V/ s. The required slew rate for a design can be calculated by the following equation: SR = 2fVpk. Careful attention to parasitic capacitances is critical to achieving the best settling time performance. The LMH6715 CIRCUIT LAYOUT With all high frequency devices, board layouts with stray capacitances have a strong influence over AC performance. The LMH6715 is no exception and its input and output pins are particularly sensitive to the coupling of parasitic capaci9 www.national.com LMH6715 Application Introduction LMH6715 Application Introduction Applications Circuits (Continued) has a typical short term settling time to 0.05% of 12ns for a 2V step. Also, the amplifier is virtually free of any long term thermal tail effects at low gains. When measuring settling time, a solid ground plane should be used in order to reduce ground inductance which can cause common-ground-impedance coupling. Power supply and ground trace parasitic capacitances and the load capacitance will also affect settling time. Placing a series resistor (Rs) at the output pin is recommended for optimal settling time performance when driving a capacitive load. The Typical Performance plot labeled "RS and Settling Time vs. Capacitive Load" provides a means for selecting a value of Rs for a given capacitive load. SINGLE-TO-DIFFERENTIAL LINE DRIVER The LMH6715's well matched AC channel-response allows a single-ended input to be transformed to highly matched push-pull driver. From a 1V single-ended input the circuit of Figure 3 produces 1V differential signal between the two outputs. For larger signals the input voltage divider (R1 = 2R2) is necessary to limit the input voltage on channel 2. DC & NOISE PERFORMANCE A current-feedback amplifier's input stage does not have equal nor correlated bias currents, therefore they cannot be canceled and each contributes to the total DC offset voltage at the output by the following equation: The input resistance is the resistance looking from the noninverting input back toward the source. For inverting DCoffset calculations, the source resistance seen by the input resistor Rg must be included in the output offset calculation as a part of the non-inverting gain equation. Application note OA-7 gives several circuits for DC offset correction. The noise currents for the inverting and non-inverting inputs are graphed in the Typical Performance plot labeled "Equivalent Input Noise". A more complete discussion of amplifier inputreferred noise and external resistor noise contribution can be found in OA-12. 20042945 FIGURE 3. Single-to-Differential Line Driver DIFFERENTIAL LINE RECEIVER Figure 4 and Figure 5 show two different implementations of an instrumentation amplifier which convert differential signals to single-ended. Figure 5 allows CMRR adjustment through R2. DIFFERENTIAL GAIN & PHASE The LMH6715 can drive multiple video loads with very low differential gain and phase errors. The Typical Performance plots labeled "Differential Gain vs. Frequency" and "Differential Phase vs. Frequency" show performance for loads from 1 to 4. The Electrical Characteristics table also specifies performance for one 150 load at 4.43MHz. For NTSC video, the performance specifications also apply. Application note OA-24 "Measuring and Improving Differential Gain & Differential Phase for Video", describes in detail the techniques used to measure differential gain and phase. I/O VOLTAGE & OUTPUT CURRENT The usable common-mode input voltage range (CMIR) of the LMH6715 specified in the Electrical Characteristics table of the data sheet shows a range of 2.2 volts. Exceeding this range will cause the input stage to saturate and clip the output signal. The output voltage range is determined by the load resistor and the choice of power supplies. With 5 volts the class A/B output driver will typically drive 3.9V into a load resistance of 100. Increasing the supply voltages will change the common-mode input and output voltage swings while at the same time increase the internal junction temperature. www.national.com 20042946 FIGURE 4. Differential Line Receiver 10 (Continued) LOW NOISE WIDE-BANDWIDTH TRANSIMPEDANCE AMPLIFIER Figure 7 implements a low noise transimpedance amplifier using both channels of the LMH6715. This circuit takes advantage of the lower input bias current noise of the noninverting input and achieves negative feedback through the second LMH6715 channel. The output voltage is set by the value of RF while frequency compensation is achieved through the adjustment of RT. 20042947 FIGURE 5. Differential Line Receiver with CMRR Adjustment NON-INVERTING CURRENT-FEEDBACK INTEGRATOR The circuit of Figure 6 achieves its high speed integration by placing one of the LMH6715's amplifiers in the feedback loop of the second amplifier configured as shown. 20042950 FIGURE 7. Low-Noise, Wide Bandwidth, Transimpedance Amp. 20042949 FIGURE 6. Current Feedback Integrator 11 www.national.com LMH6715 Applications Circuits LMH6715 Dual Wideband Video Op Amp Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin SOIC NS Package Number M08A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Support Center Fax: 65-6250 4466 Email: ap.support@nsc.com Tel: 65-6254 4466 National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: nsj.crc@jksmtp.nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated