4 - 1PCB Keyswitches
Page
MICON 5 - Short-travel keyswitches 4 - 3
MICON 5 - Short-travel keyswitches 4 - 4
MICON 5 - Plungers round, not illuminable 4 - 8
MICON 5 - Plungers square, illuminable 4 - 12
RACON - Short-travel keyswitches 4 - 17
RACON 8 - Short-travel keyswitch 4 - 18
RACON 12 - Short-travel keyswitch 4 - 22
RACON 12 V - Short-travel keyswitch with vertical adapter 4 - 26
RACON 12 i - Short-travel keyswitch 4 - 28
RACON - Special accessories 4 - 32
RK 90 II - Key cap system for RACON 12 with individual sealing 4 - 36
RF - Short-travel keyswitches 4 - 39
RF 15 - Short-travel keyswitch 4 - 42
RF 15 N - Short-travel keyswitch 4 - 48
RF 15 R - Short-travel keyswitch 4 - 52
RF 15 H - Short-travel keyswitch 4 - 58
RF 15 - Signal indicator 4 - 62
RF 19 - Short-travel keyswitch 4 - 66
RF 19 H - Short-travel keyswitch 4 - 72
RF 19 - Signal indicator 4 - 76
RF 15/19 - Special accessories 4 - 80
KN 19 - Short-travel main switch 4 - 85
KN 19 - Short-travel main switch 4 - 86
RK 90 - Keycaps 4 - 89
RK 90 - Keycaps, plastic, 9 x 9 mm 4 - 92
RK 90 - Keycaps, plastic, 14 mm 4 - 94
RK 90 - Keycaps, aluminum, 14 x 14 mm 4 - 98
RK 90 - Special accessories 4 - 100
RG 85 III - Short-travel system 4 - 103
RG 85 III - Keyswitch 4 - 106
RG 85 III - Keylock switch 4 - 110
RG 85 III - Signal indicator, without lens 4 - 114
RG 85 III - Accessories 4 - 116
RS 76 - Full-travel keyswitches 4 - 125
RS 76 M - Full-travel keyswitch, not illuminable 4 - 132
RS 76 M - Full-travel keyswitch, illuminable 4 - 134
RS 76 C - Full-travel keyswitch, not illuminable 4 - 138
RS 76 C - Full-travel keyswitch, illuminable 4 - 140
RS 76 - Keycaps, not illuminable 4 - 142
RS 76 - Keycaps, illuminable 4 - 144
RS 76 - Keycaps, with legend, two-shot moulded/keycap sets 4 - 148
RS 76 - Accessories 4 - 150
Keylock and rotary switches for PCB 4 - 153
MICROMEC - Keylock switch IP54 4 - 154
EUROLOCKS - Keylock switch IP54 4 - 158
Priority keylock switch IP54 4 - 160
Rotary switch IP40 4 - 162
PCB Keyswitches
4
NEW
NEW
4 - 2 PCB Keyswitches
4
PCB Keyswitches
CE-Conformity
The products of the Chapter "PCB Keyswitches" can –
relating to the CE-conformity according to the Low-Vol-
tage Directive 73/23/EWG – be divided into the following
groups:
All products with an operating voltage UB > 50 V
F. ex. Short-Travel Main Switch KN 19, for this product the
Low-Voltage Directive 73/23/EWG applies.
All products with an operating voltage UB < 50 V
F. ex. MICON, RACON, RF 15, RS 76, for these components
no directive applies.
Single parts, accessories and illumination
No directive applies for these products.
EMC-Law
The components of this catalogue are within the meaning
of the law concerning the electromagnetic conformity
(= EMC-Law) "basic components as, for ex., switches,
signal lamps or like" and, therefore, do not fall within the
scope of the EMC-Law.
Declarations of Conformity
Declarations of conformity for all concerned products are
available and can be delivered upon request. Please
always state the exact order reference of the respective
product.
Marking
The marking will be corresponding to the Low-Voltage
Directive 73/23/EWG resp. the Directive "CE-Marking
93/68/EWG" either on the packing or on the product itself
or on the shipping documents.
UL-approval
for MICON 5, RACON 8/12, Short-Travel Keyswitches
RF 15/19
Data entry systems wich are built with Rafi short-travel
switches according to our design proposals meet the re-
quirements of the UL approvals for the American market.
UL file no. for KN 19: E 116362
UL file no. for data entry systems: E 202520
Examples for Applications Standards
RF 15
MICON 5
RG 85 III System
RF 15 with RK 90 System
4
MICON
4 - 3PCB Keyswitches
MICON 5 - Short-travel keyswitches
General Data
Short-travel switch range MICON 5, with sealed contact system, clear key click and extremely reliable switching.
Use under overlay or under keycaps RK 90. THT and SMT versions which can be mounted automatically.
Content
MICON 5 - Short-travel keyswitches 4 - 4
MICON 5 - Short-travel keyswitch, SMT Standard 4 - 6
MICON 5 - Short-travel keyswitch, SMT low 4 - 7
MICON 5 - Short-travel keyswitch, THT Standard 4 - 7
MICON 5 - Plungers round, not illuminable 4 - 8
MICON 5 - Plunger opaque, round, not illuminable 4 - 9
MICON 5 - Plungers square, illuminable 4 - 12
MICON 5 - Plunger square, illuminable, 11 x 11 mm 4 - 13
MICON 5 - Plunger square, illuminable, 14.5 x 14.5 mm 4 - 14
MICON 5 - Plunger square, illuminable, 18 x 18 mm 4 - 15
NEW
NEW
NEW
4
MICON
4 - 4 PCB Keyswitches
MICON 5 - Short-travel keyswitches
MICON 5 - Short-travel keyswitches
NEW
General Data
MICON 5 short-travel keyswitches offer an extremely high switching reliability while needing very little space.
They can be arranged as single keys, in rows or key blocks.
When arranged under an overlay, MICON keyswitches should be combined with plungers.
The features at a glance:
s3UITABLEFORTHEMOSTCOMMONSOLDERINGMETHODS
- Wave soldering bath for THT versions
2EFLOWSOLDERINGFOR3-4VERSION
6APOURPHASESOLDERINGFOR3-4VERSIONS
- Manual soldering
s3-4VERSIONSUITABLEFORPROCESSINGWITHANAUTOMATIC3-4ASSEMBLYMACHINES
s)-$3LISTED
9OUCANDOWNLOADACTUALPRODUCTINFORMATIONFROMOURINTERNETSITEWWWRAFIDE#ATALOGUESAND$OWNLOADS
Technical Data
Dimensions
Length of housing 6.4 mm
Width of housing 5.1 mm
Overall height see order block
Mechanical design
Mounting soldering
Terminals see order block
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials Au
Illumination no
Mechanical characteristics
Operating force F1 (±20%) see order block
3WITCHINGTRAVEL3 see order block
(±0.15 mm)
Electrical characteristics
Rated voltage min. 0.02 V
Rated voltage max. 35 V
Rated current min. 0.01 mA
Rated current max. 100 mA
Rated power max. 1 W
(ohmic load)
Contact resistance when new 100 mE
Rated voltage restistance AC 250 V
Insulation resistance 109 E
Other specifications
Ambient temp. operating min. -40 °C
Ambient temp. operating max. +90 °C
Resistance to environment IEC 60068-2 -14,
-30,-33, -78
Operating life (test force) see order block
3OLDERHEATRESISTANCE see order block
3OLDERABILITY
Flammability of materials UL 94 V1
Packing see order block
Produkt code see order block
PCB Keyswitches 4 - 5
4
MICON
Operating force F1: see order block
Switching travel S2: see order block
Traceability acc. to (EN ISO 8402) DIN EN ISO 9001,
2000, 7.5.3
A 7-digit code is printed on the housing of the
keyswitch. This code informs about production date,
production shift and type of product.
week
year
day
shift
type
machine
MICON 5 Product Code acc. to DIN EN ISO 9001 (EN ISO 8402)
MICON 5 SMT Version, Tape and Reel Drawing
MICON 5 Circuit Diagram MICON 5 Force-Travel Diagram
MICON 5 - Short-travel keyswitches
4 - 6 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
MICON 5 - Short-travel keyswitches
0.35
0.05 ± 0.05
3.85 ±0.10
2.45
5.10 ±0.10
6.40 ±0.10
MICON 5 - Short-travel keyswitch, SMT Standard
Terminals Solder heat
resistance /
Solderability
Operating force
F1 (±20%)
Switching travel
S2 (±0,15 mm)
Operating life
(test force)
Produkt code Order no.
SMT %$).)%#
600 68-2-58
3.0 N 0.7 mm 1,000,000 (4 N) X1.14.002.101/0000
SMT %$).)%#
600 68-2-58
4.5 N 0.8 mm 250,000 (6 N) Z1.14.002.001/0000
SMT %$).)%#
600 68-2-58
5.5 N 0.9 mm 1,000,000 (8 N) W1.14.002.111/0000
SMT %$).)%#
600 68-2-58
8.0 N 1.1 mm 250,000 (12 N) Y1.14.002.011/0000
Technical data see page 4 - 4
Packing: in tape, reel with 2100 pieces
Keycaps see RK 90
Mounting hints:
Special pipette (Siemens Siplace order no.: 348514-02), mounting with collect and place head
Recommendation for screen printing: 150 μm stencil with 10% reduction of the pad size.
4
MICON
NEW
4
MICON
4 - 7PCB Keyswitches Stock items are marked
by bold printed order numbers.
MICON 5 - Short-travel keyswitches
0.35
3.45 ± 0.10
5.10 ± 0.10
6.40 ± 0.10
0.05 ± 0.05
MICON 5 - Short-travel keyswitch, SMT low
Terminals Solder heat
resistance /
Solderability
Operating force
F1 (±20%)
Switching travel
S2 (±0,15 mm)
Operating life
(test force)
Produkt code Order no.
SMT E DIN IEC
600 68-2-58
3.0 N 0.6 mm 1,000,000 (4 N) S1.14.002.103/0000
SMT E DIN IEC
600 68-2-58
4.5 N 0.7 mm 250,000 (6 N) T1.14.002.003/0000
SMT E DIN IEC
600 68-2-58
5.5 N 0.7 mm 1,000,000 (8 N) R1.14.002.113/0000
Technical data see page 4 - 4
Packing: in tape, reel with 2100 pieces
Keycaps see RK 90
Mounting hints:
Special pipette (Siemens Siplace order no.: 348514-02), mounting with collect and place head
Recommendation for screen printing: 150 μm stencil with 10% reduction of the pad size.
3.80 ± 0.10
5.10 ±0.10
6.40 ±0.10
2.40
6.40 ±0.20
0.35
Hole-Ø
0.70
6.35
2.54
Pad-Ø
1.50
MICON 5 - Short-travel keyswitch, THT Standard
Terminals Solder heat
resistance /
Solderability
Operating force
F1 (±20%)
Switching travel
S2 (±0,15 mm)
Operating life
(test force)
Produkt code Order no.
THT E DIN IEC
600 68-2-20
3.0 N 0.7 mm 1,000,000 (4 N) O1.14.002.106/0000
THT E DIN IEC
600 68-2-20
4.5 N 0.8 mm 250,000 (6 N) Q1.14.002.006/0000
THT E DIN IEC
600 68-2-20
5.5 N 0.9 mm 1,000,000 (8 N) N1.14.002.116/0000
THT E DIN IEC
600 68-2-20
8.0 N 1.1 mm 250,000 (12 N) P1.14.002.016/0000
Technical data see page 4 - 4
Packing: in tubes with 102 pieces
Keycaps see RK 90
NEW
NEW
4 - 8 PCB Keyswitches
MICON 5 - Short-travel keyswitches
MICON 5 - Plungers round, not illuminable
NEW
General Data
A - Height of keyswitch: SMT type: 3.85 mm, THT type: 3.80 mm
D - Length of spacer D = GH - KP - FP
FD - Front panel cut-out FD = ST + 1 mm
FP - Front panel thickness
GH - Overall height: GH = A + L1 + 0.05 (SMT type), GH = A + L 1 (THT type)
KP - Thickness of overlay + embossing
KS - Glue webs for overlay, min. 3 mm
L1 - Length of plunger above keyswitch L1 = GH - A
L - Overall length of plunger L = L1 + 1.3 mm (min. 3 mm)
RM - Key grid RM = FD + KS
ST - Diameter of plunger
The plungers can only be combined with MICON 5 version Standard (red bubble).
Technical Data
General information
Plunger diameter/size see order block
Length of plunger L see order block
4
MICON
4
MICON
4 - 9
Stock items are marked
by bold printed order numbers.
PCB Keyswitches
MICON 5 - Short-travel keyswitches
MICON 5 - Plunger opaque, round, not illuminable
Plunger diameter/size Length of plunger L Order no.
6.0 mm 3.00 mm 5.46.001.103/0200
6.0 mm 3.45 mm 5.46.001.104/0200
6.0 mm 3.95 mm 5.46.001.105/0200
6.0 mm 4.45 mm 5.46.001.106/0200
6.0 mm 7. 1 5 m m 5.46.001.107/0200
6.0 mm 9.95 mm 5.46.001.108/0200
8.0 mm 3.00 mm 5.46.001.123/0200
8.0 mm 3.45 mm 5.46.001.124/0200
8.0 mm 3.95 mm 5.46.001.125/0200
8.0 mm 4.45 mm 5.46.001.126/0200
8.0 mm 5.50 mm 5.46.001.121/0200
8.0 mm 7. 1 5 m m 5.46.001.127/0200
8.0 mm 9.95 mm 5.46.001.128/0200
8.0 mm 10.30 mm 5.46.001.122/0200
11.5 mm 3.00 mm 5.46.001.143/0200
11.5 mm 3.45 mm 5.46.001.144/0200
11.5 mm 3.95 mm 5.46.001.145/0200
11.5 mm 4.45 mm 5.46.001.146/0200
11.5 mm 5.50 mm 5.46.001.141/0200
11.5 mm 7. 1 5 m m 5.46.001.147/0200
11.5 mm 9.95 mm 5.46.001.148/0200
11.5 mm 10.30 mm 5.46.001.142/0200
NEW
4 - 10 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
MICON 5 - Short-travel keyswitches
Plunger diameter/size Length of plunger L Order no.
14.5 mm 3.00 mm 5.46.001.163/0200
14.5 mm 3.45 mm 5.46.001.164/0200
14.5 mm 3.95 mm 5.46.001.165/0200
14.5 mm 4.45 mm 5.46.001.166/0200
14.5 mm 7. 1 5 m m 5.46.001.167/0200
14.5 mm 9.95 mm 5.46.001.168/0200
19.0 mm 3.00 mm 5.46.001.183/0200
19.0 mm 3.45 mm 5.46.001.184/0200
19.0 mm 3.95 mm 5.46.001.185/0200
19.0 mm 4.45 mm 5.46.001.186/0200
19.0 mm 7. 1 5 m m 5.46.001.187/0200
19.0 mm 9.95 mm 5.46.001.188/0200
Technical data see page 4 - 8
Can only be combined with MICON 5 version Standard (red bubble)
4
MICON
MICON 5: Just feel it.
AUTOMOTIVE INSTRUMENTATION-CONTROL-
AUTOMATION
MEDICAL TECHNOLOGY
There is no miniature key-
switch which has a better
tactile and acoustic feedback
than the new RAFI MICON 5
short-travel keyswitch.
The little one shows its excellence
under keycaps, membrane over-
lays or elastic seals. Outstanding
tactile feedback and absolutely
reliable switching behaviour in
demanding applications, including
hostile environments. MICON 5 –
test it!
For samples and information,
please contact: info@rafi.de
RAFI GmbH & Co. KG
D-88276 Berg/Ravensburg
Phone: +49 751 89-0, Fax: +49 751 89-13 00
www.rafi.de, info@rafi.de
MICON 5 - Plungers square, illuminable
General Data
Description
! (EIGHTOFKEYSWITCH3-4MM4(4MM
FP - Thickness of front plate
B - Width of plunger (11 x 11 mm, 14,5 x 14,5 mm or 18 x 18 mm)
&$&RONTPANELCUTOUT"MM
+3'LUESTRIPMINMM
2 'RIDSIZE&$+3
'(/VERALLHEIGHT!MM
The plungers can only be combined with MICON 5 version Standard (red bubble).
Technical Data
General information
/VERALLHEIGHT'( see order block
Colour of lens see order block
4 - 12 PCB Keyswitches
MICON 5 - Short-travel keyswitches
4
MICON
NEW
4
MICON
4 - 13PCB Keyswitches
MICON 5 - Short-travel keyswitches
MICON 5 - Plunger square, illuminable, 11 x 11 mm
Overall height GH Colour of lens Order no.
9.70 mm red 5.05.511.470/2300
9.70 mm green 5.05.511.470/2500
9.70 mm yellow 5.05.511.470/2400
9.70 mm white 5.05.511.470/2200
9.70 mm blue 5.05.511.470/2600
12.50 mm red 5.05.511.471/2300
12.50 mm green 5.05.511.471/2500
12.50 mm yellow 5.05.511.471/2400
12.50 mm white 5.05.511.471/2200
12.50 mm blue 5.05.511.471/2600
12.50 mm opaque blue 5.05.511.476/0600
Technical data see page 4 - 12
Can only be combined with MICON 5 version Standard (red bubble)
NEW
0ICWITH,%$/32!-,/-12
Stock items are marked
by bold printed order numbers.
4 - 14 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
MICON 5 - Short-travel keyswitches
0ICWITH,%$/32!-,/-12
MICON 5 - Plunger square, illuminable, 14.5 x 14.5 mm
Overall height GH Colour of lens Order no.
9.70 mm red 5.05.511.475/2300
9.70 mm green 5.05.511.475/2500
9.70 mm yellow 5.05.511.475/2400
9.70 mm white 5.05.511.475/2200
9.70 mm blue 5.05.511.475/2600
12.50 mm red 5.05.511.476/2300
12.50 mm green 5.05.511.476/2500
12.50 mm yellow 5.05.511.476/2400
12.50 mm white 5.05.511.476/2200
12.50 mm blue 5.05.511.476/2600
Technical data see page 4 - 12
Can only be combined with MICON 5 version Standard (red bubble)
4
MICON
NEW
4
MICON
4 - 15PCB Keyswitches Stock items are marked
by bold printed order numbers.
MICON 5 - Short-travel keyswitches
0ICWITH,%$/32!-,/-12
MICON 5 - Plunger square, illuminable, 18 x 18 mm
Overall height GH Colour of lens Order no.
9.70 mm red 5.05.511.480/2300
9.70 mm green 5.05.511.480/2500
9.70 mm yellow 5.05.511.480/2400
9.70 mm white 5.05.511.480/2200
9.70 mm blue 5.05.511.480/2600
12.50 mm red 5.05.511.481/2300
12.50 mm green 5.05.511.481/2500
12.50 mm yellow 5.05.511.481/2400
12.50 mm white 5.05.511.481/2200
12.50 mm blue 5.05.511.481/2600
Technical data see page 4 - 12
Can only be combined with MICON 5 version Standard (red bubble)
NEW
4
RACON
4 - 17PCB Keyswitches
RACON - Short-travel keyswitches
General Data
RACON short-travel keyswitches with sealed contact system and distinct key click, excellent switching reliability.
For use under an overlay or with RK 90 keycaps. Print and SMD versions available (suitable for automatic assembly).
Content
RACON 8 - Short-travel keyswitch 4 - 18
RACON 8 - Short-travel keyswitch, THT outward 4 - 20
RACON 8 - Short-travel keyswitch, THT inward 4 - 20
RACON 8 - Short-travel keyswitch, SMT gullwing (Z) terminals 4 - 21
RACON 12 - Short-travel keyswitch 4 - 22
RACON 12 - Short-travel keyswitch solder terminals for PCB, outward 4 - 24
RACON 12 - Short-travel keyswitch solder terminals for PCB, inward 4 - 25
RACON 12 - Short-travel keyswitch SMT gullwing (Z) terminals 4 - 25
RACON 12 V - Short-travel keyswitch with vertical adapter 4 - 26
RACON 12 V - Short-travel keyswitch with vertical adapter 4 - 27
RACON 12 i - Short-travel keyswitch 4 - 28
RACON 12 i - Short-travel keyswitch 4 - 30
RACON - Special accessories 4 - 32
Plunger round 4 - 32
Square plunger for membrane data entry system 4 - 34
RK 90 II - Key cap system for RACON 12 with individual sealing 4 - 36
RK 90 II - Sealing frame 4 - 37
NEW
4
RACON
4 - 18 PCB Keyswitches
RACON - Short-travel keyswitches
RACON 8 - Short-travel keyswitch
F 1
2 1
2 1
0 3
product
code (F1)
production
day (21.)
production
shift (1)
production
year (2002)
production
month (03.)
General Data
RACON 8 short-travel keyswitches offer an extremely high switching reliability while needing very little space. They can
be arranged as single keys, in rows or key blocks.
When arranged under an overlay, RACON keyswitches should be combined with plungers.
The features at a glance:
s3UITABLEFORTHEMOSTCOMMONSOLDERINGMETHODS
- Wave soldering bath for THT versions
2EFLOWSOLDERINGFOR3-4VERSION
6APOURPHASESOLDERINGFOR3-4VERSIONS
-ANUALSOLDERING
s3-4VERSIONSUITABLEFORPROCESSINGWITHANAUTOMATIC3-4ASSEMBLYMACHINE
s)-$3LISTED
9OUCANDOWNLOADACTUALPRODUCTINFORMATIONFROMOURINTERNETSITEWWWRAFIDE#ATALOGUESAND$OWNLOADS
Technical Data
Dimensions
Length of housing 8.4 mm
Width of housing 8.4 mm
Height of housing see order block
Mechanical design
-OUNTING soldering
Terminals see order block
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials Au
)LLUMINATION no
Mechanical characteristics
Operating force 3.3±0.6 N
3WITCHINGTRAVEL 0.34±0.1 mm
Electrical characteristics
Rated voltage min. 0.02 V
Rated voltage max. 35 V
Rated current min. 0.01 mA
Rated current max. 100 mA
Rated power max. 1 W
(ohmic load)
Contact resistance when new 100 mE
max.
)NSULATIONRESISTANCE 109 E
Other specifications
Ambient temp. operating min. -40 °C
Ambient temp. operating max. +90 °C
Resistance to environment $).%.
-30,-33 and -78
Operating life 1,000,000
3OLDERABILITY3OLDERHEAT see order block
resistance
Flammability of materials UL 94 HB
Packing see order block
Produkt code see order block
4 - 19
4
RACON - Short-travel keyswitches
THT terminal for PCB, outward
A
L
GH
THT terminal for PCB, inward
A
L
GH
0.10
SMT gullwing (Z) terminal
A
GH
L
Variable
Height of keyswitch
Overall height
Length of plunger
Declaration
A = 4.90 +/- 0.1 mm
GH = A + L
L = GH - A L = GH - A - 0.1 mm
THT terminal
outward
THT terminal
inward
GH = A + L + 0.1 mm
SMT-terminal
THT terminal for PCB, outward THT terminal for PCB, inward SMT gullwing (Z) terminal
view on component sideview on component side view on component side
Switching symbols acc.
to IEC 617 form X
(twice interrupting)
RACON 8, Typical System Assembly with Plunger under Overlay
RACON 8, PCB Hole Pattern, Smallest Grid
RACON 8, SMT Terminal,
Tape and Reel Drawing
Circuit Diagram Typical Force-Travel
RACON 8 Diagram
RACON
PCB Keyswitches
4
RACON
4 - 20 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RACON - Short-travel keyswitches
Description Photo Order no. Additional acces-
sories see page
Typical accessories RACON 8 - Short-travel keyswitch
Spacer, round, length 6.25 mm, red 5.30.759.034/0000 2 - 231, 4 - 82, 5 - 30
Plunger round 5.46.167.311/0209 4 - 32
RK 90 - Keycap body, for lenses 9 x 9 mm 5.55.103.265/1013 4 - 93
For other plungers, refer to the chapter „RACON special accessories“; for keycaps, refer to the chapter „RK 90“.
PCB footprint, view on component side
RACON 8 - Short-travel keyswitch, THT outward
Terminals Operating force Solderability /
Solder heat
resistance
Produkt code Packing Order no.
THT outward 3.3±0.6 N E DIN IEC
600 68-2-20
A1 tubes à 60 piece 1.14.100.501/0000
Technical data see page 4 - 18
For keycaps refer to chapter „RK 90“, plungers see „RACON special accessories“.
PCB footprint, view on component side
RACON 8 - Short-travel keyswitch, THT inward
Terminals Operating force Solderability /
Solder heat
resistance
Produkt code Packing Order no.
THT inward 3.3±0.6 N E DIN IEC
600 68-2-20
B1 tubes à 60 piece 1.14.100.502/0000
Technical data see page 4 - 18
For keycaps refer to chapter „RK 90“, plungers see „RACON special accessories“.
4
RACON
4 - 21
10.60
8.40
11.00 +0.5
0.70
4.50
¯3.50
3.57
4.90 ±0.10(A)
0.10
PCB footprint, view on component side
RACON 8 - Short-travel keyswitch, SMT gullwing (Z) terminals
Terminals Operating force Solderability /
Solder heat
resistance
Produkt code Packing Order no.
SMT Gullwing
(Z) terminals
3.3±0.6 N E DIN IEC
600 68-2-58
C1 tape and reel à
1000 pieces 1.14.100.503/0000
Technical data see page 4 - 18
For keycaps refer to chapter „RK 90“, plungers see „RACON special accessories“.
PCB Keyswitches Stock items are marked
by bold printed order numbers.
RACON - Short-travel keyswitches
4
RACON
4 - 22 PCB Keyswitches
RACON - Short-travel keyswitches
RACON 12 - Short-travel keyswitch
F 1
2 1
2 1
0 3
product
code (F1)
production
day (21.)
production
shift (1)
production
year (2002)
production
month (03.)
General Data
RACON 12 short-travel keyswitches offer an extremely high switching reliability while needing very little space. They
can be arranged as single keys, in rows or key blocks.
When arranged under an overlay, RACON keyswitches should be combined with plungers.
The features at a glance:
s3UITABLEFORTHEMOSTCOMMONSOLDERINGMETHODS
- Wave soldering bath for THT versions
- Reflow soldering for SMTversions
- Vapour phase soldering for SMT versions
- Manual soldering
s3-4VERSIONSUITABLEFORPROCESSINGWITHANAUTOMATIC3-4ASSEMBLYMACHINE
s)-$3LISTED
Technical Data
Dimensions
Length of housing 12 mm
Width of housing 12 mm
Overall height see order block
Mechanical design
Mounting soldering
Terminals see order block
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials Au
Illumination no
Mechanical characteristics
Operating force see order block
Switching travel see order block
Electrical characteristics
Rated voltage min. 0.02 V
Rated voltage max. 35 V
Rated current min. 0.01 mA
Rated current max. 100 mA
Rated power max. 1 W
(ohmic load)
Contact resistance when new 100 mE
max.
Insulation resistance 109 E
Other specifications
Ambient temp. operating min. -40 °C
Ambient temp. operating max. +90 °C
Resistance to environment DIN EN 60068-2 -14,
-30,-33 and -78
Operating life 1,000,000
Solderability / Solder heat see order block
resistance
Flammability of materials UL 94 HB
Packing see order block
Produkt code see order block
4 - 23
4
RACON - Short-travel keyswitches
L
A
GH
THT terminal for PCB, outward
A
L
GH
THT terminal for PCB, inward
L
GH
A
0.10
SMT gullwing (Z) terminal
A
GH
L
Variable
Height of keyswitch
Overall height
Length of plunger
Declaration
A = 4.95 +/- 0.1 mm
GH = A + L
L = GH - A L = GH - A - 0.1 mm
THT terminal
outward
THT terminal
inward
GH = A + L + 0.1 mm
SMT-terminal
5.00
RMmin = 12.50
12.50
±
0.10
RMmin =15.24
Ø
1.20
THT terminal for PCB, outward
RMmin = 12.50
10.00
±
0.10
5.00
RMmin = 12.50
Ø
1.20
THT terminal for PCB, inward
max11.30
RMmin = 16.50
min15.80
1.60
5.00
RMmin = 12.50
SMT gullwing (Z) terminal
view on component sideview on component side view on component side
Switching symbols acc.
to IEC 617 form X
(twice interrupting)
RACON 12, Typical System Assembly with Plunger under Overlay
RACON 12, PCB Hole Pattern, Smallest Grid
RACON 12, SMT Terminal,
Tape and Reel Drawing
Circuit Diagram Typical Force-Travel
RACON 12 Diagram
RACON
PCB Keyswitches
4
RACON
4 - 24 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RACON - Short-travel keyswitches
Description Photo Order no. Additional acces-
sories see page
Typical accessories RACON 12 - Short-travel keyswitch
Spacer, round, length 6.25 mm, red 5.30.759.034/0000 2 - 231, 4 - 82, 5 - 30
Square plunger for membrane data entry system 5.46.001.057/0209 4 - 34
Plunger round 5.46.168.050/0209 4 - 33
RK 90 - Keycap body, for lens 1 -module 5.55.103.030/1013 4 - 95
For other plungers, refer to the chapter „RACON special accessories“; for keycaps, refer to the chapter „RK 90“.
PCB footprint, view on component side
RACON 12 - Short-travel keyswitch solder terminals for PCB, outward
Terminals Operating force Switching travel Solderability /
Solder heat
resistance
Produkt code Packing Order no.
THT outward 3.6±0.7 N 0.61±0.1 mm E DIN IEC
600 68-2-20
A1 tubes à
45 pieces 1.14.001.501/0000
Technical data see page 4 - 22
For keycaps refer to chapter „RK 90“, plungers see „RACON special accessories“.
PCB footprint, view on component side
RACON 12 - Short-travel keyswitch solder terminals for PCB, inward
Terminals Operating force Switching travel Solderability /
Solder heat
resistance
Produkt code Packing Order no.
THT outward 3.6±0.7 N 0.61±0.1 mm E DIN IEC
600 68-2-20
B1 tubes à
45 pieces 1.14.001.502/0000
Technical data see page 4 - 22
For keycaps refer to chapter „RK 90“, plungers see „RACON special accessories“.
5.0 ±0.15
0.86
¯3.50
3.85
4.95 ±0.10 (A)
0.10
15.00 +0.5
12.00
14.80
PCB footprint, view on component side
RACON 12 - Short-travel keyswitch SMT gullwing (Z) terminals
Terminals Operating force Switching travel Solderability /
Solder heat
resistance
Produkt code Packing Order no.
SMT Gullwing
(Z)
3.6±0.7 N 0.61±0.1 mm E DIN IEC
600 68-2-58
C1 tape and reel à
750 pieces 1.14.001.503/0000
SMT Gullwing
(Z)
6.8±1.6 N 0.7±0.1 mm E DIN IEC
600 68-2-58
ZD tape and reel à
750 pieces
1.14.001.916/0000
SMT Gullwing
(Z)
9.7±2.5 N 0.73±0.1 mm E DIN IEC
600 68-2-58
ZE tape and reel à
750 pieces
1.14.001.920/0000
Technical data see page 4 - 22
For keycaps refer to chapter „RK 90“, plungers see „RACON special accessories“.
4
RACON
4 - 25PCB Keyswitches Stock items are marked
by bold printed order numbers.
RACON - Short-travel keyswitches
4
RACON
4 - 26 PCB Keyswitches
RACON - Short-travel keyswitches
RACON 12 V - Short-travel keyswitch with vertical adapter
General Data
The RACON 12 V version can be used, for example, for PC plug-in boards and for measurement and control engineering
applications. The vertical mounting adapter (support element) absorbs the operating force so that the pressure on the
soldered terminals is reduced. For this mounting arrangement, the keyswitch is provided with two horizontal terminals
on one side.
Technical Data
Dimensions
Length 14.5 mm
Width 13.6 mm
Overall height 4.95 mm
Mechanical design
Mounting soldering
Terminals THT
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials Au
Illumination no
Mechanical characteristics
Operating force 3.6±0.7 N
Switching travel 0.61±0.1 mm
Electrical characteristics
Rated voltage min. 0.02 V
Rated voltage max. 35 V
Rated current min. 0.01 mA
Rated current max. 100 mA
Rated power max. 1 W
(ohmic load)
Contact resistance when new 100 mE
max.
Insulation resistance 109 E
Other specifications
Ambient temp. operating min. -40 °C
Ambient temp. operating max. +80 °C
Storage temperature min. -50 °C
Storage temperature max. +85 °C
(product)
Storage temperature max. +85 °C
(in tube)
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life 1,000,000
Solderability / solder heat E DIN IEC 600 68-2-20
resistance
Flammability of materials UL 94 HB
Packing in boxes à
100 pieces
Produkt code F 1
4
RACON
4 - 27PCB Keyswitches Stock items are marked
by bold printed order numbers.
RACON - Short-travel keyswitches
RACON 12 V - Short-travel keyswitch with vertical adapter
Terminals Contact arrangement Produkt code Packing Order no.
THT 1 NO F 1 in boxes à 100 pieces 1.14.001.505/0000
Technical data see page 4 - 26
Plungers for overall height of 6.5 mm may not be used.
15.00
8.20
2.10
5.00
10.00
±
0.10
6.00 ± 0.10
6.20
2.20
±
0.20
14.60
Ø
(3x)1.50
Ø
(2x)1.20
Switching symbols acc. to IEC 617 form X
(twice interrupting)
Drilling hole diagramm
view on component side
Hatched areas:
In this area no
components and
no conductor tracks
view on component side
PCB footprint RACON 12V Circuit Diagram RACON 12V
4
RACON
4 - 28 PCB Keyswitches
RACON - Short-travel keyswitches
RACON 12 i - Short-travel keyswitch
General Data
Application note
Low-profile keyboards with RACON 12 i components should be designed with a grid spacing of 15.24 mm. With this
grid, frame webs remain free between the individual keys. The overlay can be glued onto these frame webs; we recom-
mend area embossing over the keys for the overlays. If our RK 90 system design is used, we recommend the 9 x 9 mm
keycaps.
Technical Data
General information
Colour of lens see order block
Recommended key grid 15.24 x 15.24 mm
Key grid min. 12.5 x 12.5 mm
Dimensions
Length 11.35 mm
Width 11.35 mm
Overall height 9.7 mm
Mechanical design
Mounting soldering
Terminals THT
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials Au
Illumination fully illuminated
2 LED
LED colour see order block
LED type standard 2 mm
Mechanical characteristics
Operating force 3.3±0.6 N
Switching travel 0.34±0.1 mm
Electrical characteristics
Rated voltage min. 0.02 V
Rated voltage max. 35 V
Rated current min. 0.01 mA
Rated current max. 100 mA
Rated power max. 1 W
(ohmic load)
Contact resistance when new 100 mE
max.
Dielectric strength AC min. 750 V
Insulation resistance 109 E
Electrical characteristics of LED
LED rated current max. IF at red/green: 30,
25 °C yellow: 50 mA
LED current reduction red: 0.5 mA/degree C,
beginning with 50 degree C yellow 0.8 mA/
degree C
LED wavelength typ. red 639, green
510-535, yellow 590
LED forward voltage UF at 20 mA red: 1.8 V/20 mA,
yellow: 1.9 V/20 mA
LED breakdown voltage UR at min. 5 V/0.1 mA
25 °C
Other specifications
Ambient temp. operating min. -40 °C
Ambient temp. operating max. +80 °C
Storage temperature min. see order block
Storage temperature max. see order block
(product)
Storage temperature max. see order block
(intube)
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life 1,000,000
Solderability / solder heat E DIN IEC 600 68-2-20
resistance
Flammability of materials UL 94 HB
Packing tubes à 45 pieces
4 - 29
4
RACON
RACON - Short-travel keyswitches
8.50
8.90
4.50
1.00 (8x)
+
7.60
+
-
-
LED
Switching symbols acc. to IEC 60 617 form X
(twice interrupting)
Explanation
Recommended area embossing 0.35 mm at glue spacer
thickness of 0.15 mm
view on component side
view on component sideview on component side
15.24
9.2 ± 0.1
12.00
7.60 8.50
12.50
8.90
1.00
4.50
12.50
RACON 12i
typical system assembly
LED hole patterns
RACON 12i smallest grid
Circuit Diagram RACON 12i
PCB Keyswitches
4
RACON
4 - 30
illuminated area
lens red
RACON 12 i - Short-travel keyswitch
Terminals Contact arrangement Illumination Colour of lens LED colour Order no.
THT 1 NO fully illuminated
2 LED
red red 1.14.001.551/0000
THT 1 NO fully illuminated
2 LED
green green 1.14.001.552/0000
THT 1 NO fully illuminated
2 LED
yellow yellow 1.14.001.553/0000
THT 1 NO fully illuminated
2 LED
orange yellow 1.14.001.554/0000
Technical data see page 4 - 28
If keycaps are used we recommend RK 90 keycaps 9 x 9 mm.
RACON - Short-travel keyswitches
Stock items are marked
by bold printed order numbers.
PCB Keyswitches
4
RACON
4 - 32 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RACON - Short-travel keyswitches
RACON - Special accessories
Pict.: 8 mm
General Data
GH = „L“ lenth oh plunger + „A“ height of keyswitch (+ 0.1 mm for SMT versions)
Front panel cut-out = size of plunger + 1 mm
Plunger round
L
A
GH
Pict.: 8 mm
Plunger diameter/size RACON version Length of plunger L Order no.
8 mm RACON 8 1,4 mm 5.46.167.301/0209
8 mm RACON 8 1.5 mm 5.46.167.102/0209
8 mm RACON 8 1.6 mm 5.46.167.101/0209
8 mm RACON 8/12 1,9 mm 5.46.167.090/0209
8 mm RACON 8/12 2 mm 5.46.167.106/0209
8 mm RACON 8/12 2.1 mm 5.46.167.107/0209
8 mm RACON 8/12 4,6 mm 5.46.167.091/0209
8 mm RACON 8/12 4.7 mm 5.46.167.311/0209
8 mm RACON 8/12 7,4 mm 5.46.167.092/0209
8 mm RACON 8/12 4.8 mm 5.46.167.094/0209
8 mm RACON 8/12 7.5 mm 5.46.167.099/0209
8 mm RACON 8/12 7.6 mm 5.46.167.096/0209
4
RACON
4 - 33PCB Keyswitches Stock items are marked
by bold printed order numbers.
RACON - Short-travel keyswitches
Plunger diameter/size RACON version Length of plunger L Order no.
11.5 mm RACON 8 1,4 mm 5.46.167.227/0209
11.5 mm RACON 8 1.5 mm 5.46.167.061/0209
11.5 mm RACON 8 1.6 mm 5.46.167.060/0209
11.5 mm RACON 8/12 2 mm 5.46.167.067/0209
11.5 mm RACON 8/12 2.1 mm 5.46.167.064/0209
11.5 mm RACON 8/12 4,6 mm 5.46.167.043/0209
11.5 mm RACON 8/12 4.7 mm 5.46.167.050/0209
11.5 mm RACON 8/12 4.8 mm 5.46.167.047/0209
11.5 mm RACON 8/12 7.5 mm 5.46.167.059/0209
11.5 mm RACON 8/12 7.6 mm 5.46.167.058/0209
14.5 mm RACON 8 1,4 mm 5.46.168.227/0209
14.5 mm RACON 8 1.5 mm 5.46.168.061/0209
14.5 mm RACON 8 1.6 mm 5.46.168.060/0209
14.5 mm RACON 8/12 2 mm 5.46.168.067/0209
14.5 mm RACON 8/12 2.1 mm 5.46.168.064/0209
14.5 mm RACON 8/12 4,6 mm 5.46.168.043/0209
14.5 mm RACON 8/12 4.7 mm 5.46.168.050/0209
14.5 mm RACON 8/12 4.8 mm 5.46.168.047/0209
14.5 mm RACON 8/12 7,4 mm 5.46.168.044/0209
14.5 mm RACON 8/12 7.5 mm 5.46.168.059/0209
14.5 mm RACON 8/12 7.6 mm 5.46.168.058/0209
19 mm RACON 8 1.5 mm 5.46.169.061/0209
19 mm RACON 8 1.6 mm 5.46.169.060/0209
19 mm RACON 8/12 2 mm 5.46.169.067/0209
19 mm RACON 8/12 2.1 mm 5.46.169.064/0209
19 mm RACON 8/12 4.7 mm 5.46.169.050/0209
19 mm RACON 8/12 4.8 mm 5.46.169.047/0209
19 mm RACON 8/12 7.5 mm 5.46.169.059/0209
4
RACON
4 - 34 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RACON - Short-travel keyswitches
Plunger diameter/size RACON version Length of plunger L Order no.
19 mm RACON 8/12 7.6 mm 5.46.169.058/0209
Front panel cut-out = Plunger diameter + 1 mm.
Square plunger for membrane data entry system
A
L
GH
Plunger diameter/size RACON version Length of plunger L Order no.
14 x 14 mm RACON 12 THT 2.1 mm 5.46.001.064/0209
14 x 14 mm RACON 12 THT 4.8 mm 5.46.001.060/0209
14 x 14 mm RACON 12 THT 7.6 mm 5.46.001.063/0209
14 x 14 mm RACON 12 SMT 2 mm 5.46.001.057/0209
14 x 14 mm RACON 12 SMT 4.7 mm 5.46.001.058/0209
14 x 14 mm RACON 12 SMT 7.5 mm 5.46.001.059/0209
Front panel cut-out = 15 x 15 mm.
4
RACON
4 - 36 PCB Keyswitches
RACON - Short-travel keyswitches
RK 90 II, Key cap system for RACON 12 with individual sealing
NEW
Technical Data
General information
Thickness of front panel 3.00 mm
Light conductor see order block
Key grid min. 16.8 x 17.5 mm
Degree of protection IP 65
The key cap system RK 90 II has been developed especially fort he short-travel keyswitch RACON 12. The lenses are
snapped onto the sealing frame and then set onto the RACON 12 keyswitches. The PCB presses this units against the
front panel, so they are sealed.
Two versions of the sealing frames are provided with light conductors, either in square ore triangle form.
The lenses can be legended directly with laser. For bright letters (see picture) first white lenses are painted in dark, then
the letters are cut out of the dark colour with laser.
4
RACON
4 - 37PCB Keyswitches Stock items are marked
by bold printed order numbers.
RACON - Short-travel keyswitches
RK 90 II - Sealing frame
with snapped-on lens
Thickness of front panel Light conductor Order no.
without lens
Note
3.00 mm square 5.05.004.901/0000 Please order lens separately.
3.00 mm triangular 5.05.004.902/0000 Please order lens separately.
3.00 mm -5.05.004.903/0000 Please order lens separately.
Technical data see page 4 - 36
Lenses:
Lens RK 90 II, white: 5.46.654.192/0200
Lens RK 90 II, red: 5.46.654.192/0300
Lens RK 90 II, green: 5.46.654.192/0500
Lens RK 90 II, blue: 5.46.654.192/0600
Lens RK 90 II, yellow: 5.46.654.192/0400
Lens RK 90 II, grey: 5.46.654.192/0700
Lens RK 90 II, iron grey (varnished): 5.46.654.192/6033
Lens RK 90 II, grey (varnished): 5.46.654.192/6032
Legended lenses on request.
Sealing frame with square light conductor
4
RF
4 - 39PCB Keyswitches
RF - Short-travel keyswitches
General Data
RF 15 (15 x 15 mm) and RF 19 (19 x 19 mm) with distinct key click, for use under an overlay or with RK 90 keycaps.
Can be fully illuminated.
Content
RF 15 - Short-travel keyswitch 4 - 42
RF 15 - Short-travel keyswitch, non-illuminated 4 - 44
RF 15 - Short-travel keyswitch, fully illuminated with 2 LED 4 - 45
RF 15 - Short-travel keyswitch, 1 LED spot-illumination 4 - 46
RF 15 N - Short-travel keyswitch 4 - 48
RF 15 N - Short-travel keyswitch, non-illuminated 4 - 51
RF 15 R - Short-travel keyswitch 4 - 52
RF 15 R - Low short-travel keyswitch, non-illuminated 4 - 55
RF 15 R - High short-travel keyswitch, non-illuminated 4 - 55
RF 15 R - Low short-travel keyswitch, 1 LED spot-illumination 4 - 56
RF 15 R - High short-travel keyswitch, 1 LED spot-illumination 4 - 57
RF 15 H - Short-travel keyswitch 4 - 58
RF 15 H - Short-travel keyswitch, non-illuminated 4 - 60
RF 15 H - Short-travel keyswitch, fully illuminated 4 - 61
RF 15 - Signal indicator 4 - 62
RF 15 - Signal indicator, fully illuminated, 1 LED 4 - 64
RF 19 - Short-travel keyswitch 4 - 66
RF 19 - Short-travel keyswitch, non-illuminated 4 - 69
RF 19 - Short-travel keyswitch, fully illuminated with 2 LED 4 - 70
RF 19 - Short-travel keyswitch, 1 LED spot-illumination 4 - 71
RF 19 H - Short-travel keyswitch 4 - 72
RF 19 H - Keyswitch, non-illuminated 4 - 74
RF 19 H - Short-travel keyswitch, fully illuminated 4 - 75
RF 19 - Signal indicator 4 - 76
RF 19 - Signal indicator, ½ x 1-module 4 - 78
RF 19 - Signal indicator, ½ x 2-module 4 - 78
RF 19 - Signal indicator, 1 x 1-module 4 - 79
RF 19 - Signal indicator, 1 x 2-module 4 - 79
4
RF
4 - 40
RF 15/19 - Special accessories 4 - 80
RF 15 N - Extension plunger, round head 4 - 80
RF 15 N - Extension plunger, round head, with recess for LED 4 - 81
RF 15 - Keycap, snap-on, for overall height 12.5 mm 4 - 81
Spacers, round 4 - 82
Spacers, triangular 4 - 83
RF 15 N - LED spacer 4 - 84
PCB Keyswitches
RF - Short-travel keyswitches
4 - 41
4
RF
RF - Short-travel keyswitches
Specifications LED
3 mm LED
2 mm LED (full illumination of RF 15/19)
Max. forward current lF:
Current reduction from: T0 = 50 °C:
Wavelength typ:
Forward voltage UF/lF typ:
Reverse voltage UR/lF typ:
Ambient temperature, operating:
(valid for 25 °C)
30 mA
approx 0.5 mA/°C
635 nm
2 V/10 mA
5 V/100 μA min.
- 20 °C . . . + 80 °C
Red LED
30 mA
approx 0.5 mA/°C
565 nm
2 V/10 mA
5 V/100 μA min.
- 20 °C . . . + 80 °C
Green LED
20 mA
approx 0.2 mA/°C
586 nm
2 V/10 mA
5 V/100 μA min.
- 20 °C . . . + 80 °C
Yellow LED
Max. forward current lF:
Current reduction from: T0 = 50 °C:
Wavelength typ:
Forward voltage UF/lF typ:
Reverse voltage UR/lF typ:
Ambient temperature, operating:
20 mA
approx 0.6 mA/°C
470 nm
2.7 V/10 mA
5V/100 μA min.
- 20 °C . . . + 80 °C
Blue LED
25 mA
-
-
3.6 V/20 mA
-
- 20 °C . . . + 80 °C
White LED
30 mA
-
510-545 nm
3.5 V/20 mA
-
-30 °C . . . + 100 °C
Green LED superbright
Max. forward current lF:
Current reduction from: T0 = 50 °C:
Light current fV/lF typ:
Wavelength typ:
Forward voltage UF/lF typ:
Reverse voltage UR/lF typ:
Ambient temperature, operating:
(valid for 25 °C)
30 mA
0.5 mA/°C
-
637 nm
1.8 V/20 mA
5 V/100 μA min.
- 55 °C . . . + 100 °C
Red LED
30 mA
0.5 mA/°C
-
569 nm
2.1 V/10 mA
5 V/100 μA min.
- 40 °C . . . + 100 °C
Green LED
50 mA
0.8 mA/°C
250 mIm/20 mA
590 nm
1.9 V/20 mA
5 V/100 μA min.
-40 °C . . . + 100 °C
Yellow LED
Max. forward current lF:
Current reduction from: T0 = 50 °C:
Light current fV/lF typ:
Wavelength typ:
Forward voltage UF/lF typ:
Reverse voltage UR/lF typ:
Ambient temperature, operating:
30 mA
-
-
464-485 nm
3.6 V/20 mA
- 20 °C . . . + 80 °C
Blue LED
30 mA
approx 0.6 mA/°C
-
635/565 nm
2 V/10 mA
-
- 20 °C . . . + 80 °C
Multi-colour LED
Rated power
of series:
PV = IF2 x RV
Calculating the
series resistor:
RV =
Example for 5 Volt:
RV = = 150 Ω (= standard value)
UB - UF
IF
5V - 2,0 V
0,02 A
PCB Keyswitches
4
RF
4 - 42 PCB Keyswitches
RF - Short-travel keyswitches
RF 15 - Short-travel keyswitch
General Data
Low-profile keyboards with RF 15 components should be designed with a 19.05 mm grid. With this grid, frame webs
remain free between the individual keys. The overlay can be glued onto these frame webs; we recommend area
embossing over the keys for the overlays.
Technical Data
General information
Colour of lens see order block
Recommended key grid 19.05 mm
Dimensions
Length 15 mm
Width 15 mm
Overall height 9.7 mm
Mechanical design
Mounting soldering in PCB
Terminals THT
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials see order block
Illumination see order block
LED colour see order block
LED type see order block
Mechanical characteristics
Operating force max. 2.9±0.6 N
Switching travel 0.5+0.2 mm
Robustness min. with through-plated
PCB 100 N
Electrical characteristics
Rated voltage min. Au: 0.02 V, Ag: 3 V
Rated voltage max. Au: 35 V, Ag: 50 V
Rated current min. Au: 0.01 mA,
Ag: 0.1 mA
Rated current max. Au: 100 mA,
Ag: 250 mA
Rated power max. Au: 2 W, Ag: 12.5 W
(ohmic load)
Contact resistance when new 100 mE
max.
Insulation resistance 109 E
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. 1,000,000
(operations)
Solderability / solder heat according to E DIN
resistance IEC 600 28-2-20
Wave soldering 260 °C max.
Manual soldering 350 °C / 5 sec. max.
4 - 43
4
RF
RF - Short-travel keyswitches
View on component side, all hole diameters 1,1 +/- 0,1 mm
Operation characteristic limits RF
Keyswitch,
non-illuminated
Keyswitch,
fully illuminated
Keyswitch,
spot-illuminated
Force/Travel Diagram – Keyswitch RF 15
Hole Pattern RF 15
Circuit Diagram – Keyswitch RF 15
Hole Pattern – Front Panel
Dimensional Drawing RF 15
PCB Keyswitches
4
RF
4 - 44 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
RF 15 - Short-travel keyswitch, non-illuminated
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au not illuminated transparent - - 3.14.100.001/0000
Ag not illuminated transparent - - 3.14.100.006/0000
Technical data see page 4 - 42
For keycaps, refer to chapter accessories and system RK 90.
If exchangeable legends are required, or if an overall height of 12.5 mm is required, a keycap can be mounted on the
non-illuminated keys. The keycap legend is visible through a window in the overlay. You can change the legend by
replacing the keycap.
4
RF
4 - 45PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Illuminated area
10.8 x 10.8 mm
Overall height
Housing
Actuator
Lens
Pict.: red
RF 15 - Short-travel keyswitch, fully illuminated with 2 LED
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au fully illuminated
2 LED
red red 2 mm 3.14.200.011/0000
Au fully illuminated
2 LED
green green 2 mm 3.14.200.012/0000
Au fully illuminated
2 LED
yellow yellow 2 mm 3.14.200.013/0000
Au fully illuminated
2 LED
orange yellow 2 mm 3.14.200.014/0000
Au fully illuminated
2 LED
blue blue 2 mm 3.14.200.015/0000
Ag fully illuminated
2 LED
red red 2 mm 3.14.200.021/0000
Ag fully illuminated
2 LED
green green 2 mm 3.14.200.022/0000
Ag fully illuminated
2 LED
yellow yellow 2 mm 3.14.200.023/0000
Ag fully illuminated
2 LED
orange yellow 2 mm 3.14.200.024/0000
Ag fully illuminated
2 LED
blue blue 2 mm 3.14.200.025/0000
Technical data see page 4 - 42
For keycaps, refer to RK 90 system design.
Technical data of LED see seperate page at the beginning of this chapter.
4
RF
4 - 46
RF 15 - Short-travel keyswitch, 1 LED spot-illumination
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au spot illumination
1 LED
opaque white blue 3 mm 3.14.100.030/0000
Au spot illumination
1 LED
opaque white red 3 mm 3.14.100.031/0000
Au spot illumination
1 LED
opaque white green 3 mm 3.14.100.032/0000
Au spot illumination
1 LED
opaque white yellow 3 mm 3.14.100.033/0000
Ag spot illumination
1 LED
opaque white blue 3 mm 3.14.100.040/0000
Ag spot illumination
1 LED
opaque white red 3 mm 3.14.100.041/0000
Ag spot illumination
1 LED
opaque white green 3 mm 3.14.100.042/0000
Ag spot illumination
1 LED
opaque white yellow 3 mm 3.14.100.043/0000
Technical data see page 4 - 42
Double-spot LED illumination available on request
Technical data of LED see seperate page at the beginning of this chapter.
Stock items are marked
by bold printed order numbers.
PCB Keyswitches
RF - Short-travel keyswitches
4
RF
4 - 48 PCB Keyswitches
RF - Short-travel keyswitches
RF 15 N - Short-travel keyswitch
General Data
The RF 15N keyswitch provides a minimum overall height of 6.2 mm. The overall height can be varied by extension
plungers which are inserted into the cross-like notches on the actuator tops.
LEDs can only be arranged separately next to the keyswitches up to an overall height of 10 mm (i.e. without plunger or
with small plunger).
Keyswitches with overall heights of 12 mm or more can be provided with a maximum of 2 LEDs which are inserted into
the recesses of the keyswitch housing. LEDs of keyswitches with overall heights of 12.5 mm or more should be placed
onto LED spacers in order to obtain satisfactory illumination.
Technical Data
General information
Colour of lens see order block
Recommended key grid 19.05 mm
Dimensions
Length 15 mm
Width 15 mm
Overall height 6.2 mm
Mechanical design
Mounting soldering in PCB
Terminals THT
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials see order block
Illumination external 3 mm LED
possible if height
more than 12 mm
Mechanical characteristics
Operating force max. 2.9±0.6 N
Switching travel 0.5+0.2 mm
Robustness min. 100 with through-
plated PCB N
Electrical characteristics
Rated voltage min. Au: 0.02 V, Ag: 3 V
Rated voltage max. Au: 35 V, Ag: 50 V
Rated current min. Au: 0.01 mA,
Ag: 0.1 mA
Rated current max. Au: 100 mA,
Ag: 250 mA
Rated power max. Au: 2 W, Ag: 12.5 W
(ohmic load)
Contact resistance when new 100 mE
max.
Insulation resistance 109 E
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Storage temperature max. +50 °C
(in tube)
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. 1,000,000
(operations)
Solderability / solder heat according to E DIN
resistance IEC 600 28-2-20
Wave soldering 260 °C max.
Manual soldering 350 °C / 5 sec. max.
4 - 49
4
RF
RF - Short-travel keyswitches
Operation characteristic limits RF
Keyswitch,
non illuminated
Keyswitch,
spot-illuminated
Force/Travel Diagram – Keyswitch RF 15 N Circuit Diagram – Keyswitch RF 15 N
Dimensional Drawings RF 15 N
PCB Keyswitches
RF - Short-travel keyswitches
4 - 50
4
RF
RF 15 N without plunger RF 15 N with plunger ø 10 mm, non-illuminated
RF 15 N with plunger ø 10 mm, illuminated RF 15 N with plunger ø 15 mm, illuminated
View on component side
All hole diameters 1.1 +/- 0.1 mm
PCB layout keyswitch 1/400” grid
Hole Pattern RF 15 N
Hole Patterns – Front Panel RF 15 N
PCB Keyswitches
4
RF
4 - 51PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Description Photo Order no. Additional acces-
sories see page
Typical accessories RF 15 N - Short-travel keyswitch
RF 15 N - LED spacer Ø 5 mm, spacing length 2.2 mm,
light grey, for use with overall height of 12.5 mm
5.30.109.010/0756 4 - 84
RF 15 N - Extension plunger, Ø 10 mm, overall height
22.5 mm 5.46.011.028/0710 4 - 80
RF 15 N - Extension plunger, Ø 15 mm, overall height
22.5 mm
5.46.017.028/0710 4 - 81
RF 15 N - Short-travel keyswitch, non-illuminated
Contact materials Illumination Recommended key grid Overall height Order no.
Au external 3 mm LED possible if
height more than 12 mm
19.05 mm 6.2 mm 3.14.100.601/0000
Ag external 3 mm LED possible if
height more than 12 mm
19.05 mm 6.2 mm 3.14.100.606/0000
Technical data see page 4 - 48
For keycaps, refer to RK 90 system design.
Double-spot LED illumination available on request.
4
RF
4 - 52 PCB Keyswitches
RF - Short-travel keyswitches
RF 15 R - Short-travel keyswitch
Pict.: with 2 mm LED, red
with 3 mm LED, green
General Data
The round actuator of the RF 15 R keyswitch requires round front panel cut-outs. These make it possible to use a narrow
keyboard grid of only 15.24 mm with sufficiently large frame webs between the individual keys. We recommend area
embossing over the actuators for the overlay.
Technical Data
General information
Recommended key grid 15.24 mm
Dimensions
Length 15 mm
Width 15 mm
Overall height see order block
Mechanical design
Mounting soldering in PCB
Terminals THT
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials see order block
Illumination see order block
LED colour see order block
LED type see order block
Mechanical characteristics
Operating force max. 2.9±0.6 N
Switching travel 0.5+0.2 mm
Robustness min. with through-plated
PCB 100 N
Electrical characteristics
Rated voltage min. Au: 0.02 V, Ag: 3 V
Rated voltage max. Au: 35 V, Ag: 50 V
Rated current min. Au: 0.01 mA,
Ag: 0.1 mA
Rated current max. Au: 100 mA,
Ag: 250 mA
Rated power max. Au: 2 W, Ag: 12.5 W
(ohmic load)
Contact resistance when new 100 mE
max.
Insulation resistance 109 E
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. 1,000,000
(operations)
Solderability / solder heat according to E DIN
resistance IEC 600 28-2-20
Wave soldering 260 °C max.
Manual soldering 350 °C / 5 sec. max.
4 - 53
4
RF
RF - Short-travel keyswitches
View on component side
All hole diameters 1.1 +/- 0.1 mm
PCB layout keyswitch 1/400” grid
Operation characteristic limits RF
Keyswitch,
non-illuminated
Keyswitch,
spot-illuminated
Hole Pattern RF 15 R
Circuit Diagram – Keyswitch RF 15 RForce/Travel Diagram – Keyswitch RF 15 R
Dimensional Drawing RF 15 R
PCB Keyswitches
4 - 54
4
RF
RF - Short-travel keyswitches
RF 15 R, non-illuminated RF 15 R, illuminated
Hole Pattern – Front Panel RF 15 R
PCB Keyswitches
4
RF
4 - 55PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
RF 15 R - Low short-travel keyswitch, non-illuminated
Contact materials Overall height Illumination LED type LED colour Order no.
Au 9.7 mm not illuminated - - 3.14.100.501/0000
Ag 9.7 mm not illuminated - - 3.14.100.506/0000
Technical data see page 4 - 52
RF 15 R - High short-travel keyswitch, non-illuminated
Contact materials Overall height Illumination LED type LED colour Order no.
Au 12.5 mm not illuminated - - 3.14.100.801/0000
Ag 12.5 mm not illuminated - - 3.14.100.806/0000
Technical data see page 4 - 52
Overall height
4
RF
4 - 56 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Pict.: with 2 mm LED, red
RF 15 R - Low short-travel keyswitch, 1 LED spot-illumination
Contact materials Overall height Illumination LED type LED colour Order no.
Au 9.7 mm spot illumination
1 LED
2 mm red 3.14.100.531/0000
Au 9.7 mm spot illumination
1 LED
2 mm green 3.14.100.532/0000
Au 9.7 mm spot illumination
1 LED
2 mm yellow 3.14.100.533/0000
Ag 9.7 mm spot illumination
1 LED
2 mm red 3.14.100.541/0000
Ag 9.7 mm spot illumination
1 LED
2 mm green 3.14.100.542/0000
Ag 9.7 mm spot illumination
1 LED
2 mm yellow 3.14.100.543/0000
Technical data see page 4 - 52
Versions with 2 LEDs available on request.
Technical data of LED see seperate page at the beginning of this chapter.
4
RF
4 - 57PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Pict.: with 3 mm LED, green
RF 15 R - High short-travel keyswitch, 1 LED spot-illumination
Contact materials Overall height Illumination LED type LED colour Order no.
Au 12.5 mm spot illumination
1 LED
3 mm blue 3.14.100.830/0000
Au 12.5 mm spot illumination
1 LED
3 mm red 3.14.100.831/0000
Au 12.5 mm spot illumination
1 LED
3 mm green 3.14.100.832/0000
Au 12.5 mm spot illumination
1 LED
3 mm yellow 3.14.100.833/0000
Technical data see page 4 - 52
Versions with 2 LEDs available on request.
Technical data of LED see seperate page at the beginning of the chapter.
4
RF
4 - 58 PCB Keyswitches
RF - Short-travel keyswitches
RF 15 H - Short-travel keyswitch
General Data
Application notes:
The RF 15 H key has an overall height of 12.5 mm and can be fully illuminated. When designing membrane keyboards,
we recommend using a key grid of at least 20 mm and a 0.13 mm overlay with area embossing over the keys.
You can use the O-ring (accessory) to block the key and use it as an indicator field or blank spaceholder.
Technical Data
General information
Colour of lens see order block
Recommended key grid 20 mm
Dimensions
Length 15 mm
Width 15 mm
Overall height 12.5 mm
Mechanical design
Mounting soldering in PCB
Terminals THT
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials see order block
Illumination see order block
LED colour see order block
LED type see order block
Mechanical characteristics
Operating force max. 2.9±0.6 N
Switching travel 0.5+0.2 mm
Robustness min. with through-plated
PCB 100 N
Electrical characteristics
Rated voltage min. Au: 0.02 V, Ag: 3 V
Rated voltage max. Au: 35 V, Ag: 50 V
Rated current min. Au: 0.01 mA,
Ag: 0.1 mA
Rated current max. Au: 100 mA,
Ag: 250 mA
Rated power max. (ohmic Au: 2 W, Ag: 12.5 W
load)
Contact resistance when new 100 mE
max.
Insulation resistance 109 E
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. 1,000,000
(operations)
Solderability / solder heat according to E DIN
resistance IEC 600 28-2-20
Wave soldering 260 °C max.
Manual soldering 350 °C / 5 sec. max.
4 - 59
4
RF
RF - Short-travel keyswitches
Operation characteristic limits RF
Keyswitch,
non-illuminated
Keyswitch,
fully illuminated
View on component side. All hole diameters 1,1 +/- 0,1 mm.
PCB layout keyswitch 1/400 grid.
Hole Pattern
Force/Travel Diagram – Keyswitch RF 15 H
Hole Pattern – Front Panel
Circuit Diagram – Keyswitch RF 15 H
Dimensional Drawing
PCB Keyswitches
4
RF
4 - 60 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Description Photo Order no. Additional acces-
sories see page
Typical accessories RF 15 H - Short-travel keyswitch
O-ring, black, for blocking the operating stroke 5.30.120.009/0100 5 - 25
overall height
housing
actuator
lens
illuminated area
RF 15 H - Short-travel keyswitch, non-illuminated
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au not illuminated white - - 3.14.100.702/0000
Ag not illuminated white - - 3.14.100.707/0000
Technical data see page 4 - 58
overall height
housing
actuator
lens
illuminated area
Pict.: yellow
RF 15 H - Short-travel keyswitch, fully illuminated
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au fully illuminated
2 LED
red red 2 mm 3.14.200.731/0000
Au fully illuminated
2 LED
green green 2 mm 3.14.200.732/0000
Au fully illuminated
1 LED
green green super bright 3 mm 3.14.200.736/0000
Au fully illuminated
2 LED
yellow yellow 2 mm 3.14.200.733/0000
Au fully illuminated
1 LED
white white 3 mm 3.14.200.735/0000
Au fully illuminated
2 LED
orange yellow 2 mm 3.14.200.738/0000
Au fully illuminated
1 LED
blue blue 3 mm 3.14.200.739/0000
Au/Ag fully illuminated
2 LED
yellow multi colour 3 mm 3.14.101.903/0000
Ag fully illuminated
2 LED
red red 2 mm 3.14.200.741/0000
Ag fully illuminated
2 LED
green green 2 mm 3.14.200.742/0000
Ag fully illuminated
1 LED
green green super bright 3 mm 3.14.200.746/0000
Ag fully illuminated
2 LED
yellow yellow 2 mm 3.14.200.743/0000
Ag fully illuminated
1 LED
white white 3 mm 3.14.200.745/0000
Ag fully illuminated
2 LED
orange yellow 2 mm 3.14.200.748/0000
Ag fully illuminated
1 LED
blue blue 3 mm 3.14.200.749/0000
Ag fully illuminated
2 LED
white multi colour 3 mm 3.14.100.744/0000
Technical data see page 4 - 58
When using the keyswitches with multicolour LEDs the illumination colour can be varied from red to green by change
of polarity. Due to the frequency of the polarity-changes the colours red, green, yellow as well as all secondary colours
from these are possible.
Technical data of LED see separate page at the beginning of this chapter.
4
RF
4 - 61PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
4
RF
4 - 62 PCB Keyswitches
RF - Short-travel keyswitches
RF 15 - Signal indicator
Technical Data
General information
Colour of lens see order block
Recommended key grid 19.05 mm
Dimensions
Length 15 mm
Width 15 mm
Overall height 9.7 mm
Mechanical design
Mounting THT soldering in PCB
Illumination fully illuminated
1 LED
LED colour see order block
LED type 2 mm
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Solderability / solder heat according to E DIN
resistance IEC 600 28-2-20
Wave soldering 260 °C max.
Manual soldering 350 °C / 5 sec. max.
4 - 63
4
RF
RF - Short-travel keyswitches
View on component side, all hole diameters 1,1 +/- 0,1 mm
Hole Pattern Hole Pattern – Front Panel
Dimensional Drawing Signal Indicator RF 15
PCB Keyswitches
4
RF
4 - 64
Illuminated area
10.8 x 10.8 mm
Housing
Lens
Pict.: green
RF 15 - Signal indicator, fully illuminated, 1 LED
Overall height Illumination Colour of lens LED colour LED type Order no.
9.7 mm fully illuminated
1 LED
red red 2 mm 3.14.200.051/0000
9.7 mm fully illuminated
1 LED
green green 2 mm 3.14.200.052/0000
9.7 mm fully illuminated
1 LED
yellow yellow 2 mm 3.14.200.053/0000
9.7 mm fully illuminated
1 LED
orange yellow 2 mm 3.14.200.054/0000
9.7 mm fully illuminated
1 LED
blue blue 2 mm 3.14.200.055/0000
Technical data see page 4 - 62
Technical data of LED see separate page at the beginning of chapter 4 PCB Keyswitches.
Stock items are marked
by bold printed order numbers.
PCB Keyswitches
RF - Short-travel keyswitches
4
RF
4 - 66 PCB Keyswitches
RF - Short-travel keyswitches
RF 19 - Short-travel keyswitch
General Data
Application notes:
RF 19 keys offer a large actuation area. When designing low-profile keyboards with a grid of >= 23 mm, frame webs
remain free between the individual keys.
The overlay can be glued onto these frame webs; we recommend area embossing over the keys for the overlay.
Technical Data
General information
Colour of lens see order block
Recommended key grid 23 mm
Dimensions
Length 19.05 mm
Width 19.05 mm
Overall height 9.7 mm
Mechanical design
Mounting soldering in PCB
Terminals THT
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials see order block
Illumination see order block
LED colour see order block
LED type see order block
Mechanical characteristics
Operating force max. 2.9±0.6 N
Switching travel 0.5+0.2 mm
Robustness min. with through-plated
PCB 100 N
Electrical characteristics
Rated voltage min. Au: 0.02 V, Ag: 3 V
Rated voltage max. Au: 35 V, Ag: 50 V
Rated current min. Au: 0.01 mA,
Ag: 0.1 mA
Rated current max. Au: 100 mA,
Ag: 250 mA
Rated power max. Au: 2 W, Ag: 12.5 W
(ohmic load)
Contact resistance when new 100 mE
max.
Insulation resistance 109 E
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. 1,000,000
(operations)
Solderability / solder heat according to E DIN
resistance IEC 600 28-2-20
Wave soldering 260 °C max.
Manual soldering 350 °C / 5 sec. max.
4 - 67
4
RF
RF - Short-travel keyswitches
Operation characteristic limits RF
Keyswitch,
non-illuminated
Keyswitch,
fully illuminated
Keyswitch,
spot-illuminated
Force/Travel Diagram – Keyswitch RF 19 Circuit Diagram – Keyswitch RF 19
Dimensional Drawing
PCB Keyswitches
4 - 68
4
RF
RF - Short-travel keyswitches
* The LED may be positioned either on the left-hand or right-hand side.
Standard version: LED on left-hand side
View on component side, all hole diameters 1.1 +/- 0.1 mm
Hole Patterns – Front Panel RF 19
Hole Patterns RF 19
PCB Keyswitches
4
RF
4 - 69PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Housing
Actuator
Overall hight
RF 19 - Short-travel keyswitch, non-illuminated
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au not illuminated transparent - - 3.14.001.001/0000
Ag not illuminated transparent - - 3.14.001.006/0000
Technical data see page 4 - 66
4
RF
4 - 70 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
RF 19 - Short-travel keyswitch, fully illuminated with 2 LED
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au fully illuminated
2 LED
red red 2 mm 3.14.002.011/0000
Au fully illuminated
2 LED
green green 2 mm 3.14.002.012/0000
Au fully illuminated
2 LED
opaque white green 2 mm 3.14.002.901/0000
Au fully illuminated
2 LED
yellow yellow 2 mm 3.14.002.013/0000
Au fully illuminated
2 LED
orange yellow 2 mm 3.14.002.014/0000
Au fully illuminated
2 LED
blue blue 2 mm 3.14.002.015/0000
Ag fully illuminated
2 LED
red red 2 mm 3.14.002.021/0000
Ag fully illuminated
2 LED
green green 2 mm 3.14.002.022/0000
Ag fully illuminated
2 LED
yellow yellow 2 mm 3.14.002.023/0000
Ag fully illuminated
2 LED
orange yellow 2 mm 3.14.002.024/0000
Ag fully illuminated
2 LED
blue blue 2 mm 3.14.002.025/0000
Ag fully illuminated
2 LED
opaque white green 2 mm 3.14.002.944/0000
Ag fully illuminated
2 LED
white green 2 mm 3.14.002.026/0000
Ag fully illuminated
2 LED
white yellow 2 mm 3.14.002.027/0000
Technical data see page 4 - 66
Technical data of LED see separate page at the beginning of this chapter.
4
RF
4 - 71PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Pict.: red
RF 19 - Short-travel keyswitch, 1 LED spot-illumination
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au spot illumination
1 LED
opaque white blue 3 mm 3.14.001.030/0000
Au spot illumination
1 LED
opaque white red 3 mm 3.14.001.031/0000
Au spot illumination
1 LED
opaque white green 3 mm 3.14.001.032/0000
Au spot illumination
1 LED
opaque white yellow 3 mm 3.14.001.033/0000
Ag spot illumination
1 LED
opaque white blue 3 mm 3.14.001.040/0000
Ag spot illumination
1 LED
opaque white red 3 mm 3.14.001.041/0000
Ag spot illumination
1 LED
opaque white green 3 mm 3.14.001.042/0000
Ag spot illumination
1 LED
opaque white yellow 3 mm 3.14.001.043/0000
Technical data see page 4 - 66
Versions with 2 LEDs available on request.
Technical data of LED see separate page at the beginning of this chapter.
4
RF
4 - 72 PCB Keyswitches
RF - Short-travel keyswitches
RF 19 H - Short-travel keyswitch
General Data
Application notes:
The RF 19H key has an overall height of 12.5 mm and can be fully illuminated. When designing membrane keyboards,
we recommend using a key grid of at least 24 mm and a 0.13 mm overlay with area embossing over the keys.
You can use the O-ring (accessory) to block the key and use it as an indicator field or blank spaceholder.
Technical Data
General information
Colour of lens see order block
Recommended key grid 24 mm
Dimensions
Length 19.05 mm
Width 19.05 mm
Overall height 12.5 mm
Mechanical design
Mounting soldering in PCB
Terminals THT
Contact system snap-action contact
Contact arrangement 1 NO
Contact materials see order block
Illumination see order block
LED colour see order block
LED type see order block
Mechanical characteristics
Operating force max. 2.9±0.6 N
Switching travel 0.5+0.2 mm
Robustness min. with through-plated
PCB 100 N
Electrical characteristics
Rated voltage min. Au: 0.02 V, Ag: 3 V
Rated voltage max. Au: 35 V, Ag: 50 V
Rated current min. Au: 0.01 mA,
Ag: 0.1 mA
Rated current max. Au: 100 mA,
Ag: 250 mA
Rated power max. (ohmic Au: 2 W, Ag: 12.5 W
load)
Contact resistance when new 100 mE
max.
Insulation resistance 109 E
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. 1,000,000
(operations)
Solderability / solder heat according to E DIN
resistance IEC 600 28-2-20
Wave soldering 260 °C max.
Manual soldering 350 °C / 5 sec. max.
4 - 73
4
RF
RF - Short-travel keyswitches
Operation characteristic limits RF
Keyswitch,
non illuminated
Keyswitch,
fully illuminated
Force/Travel Diagram – Keyswitch RF 19 H Circuit Diagram – Keyswitch RF 19 H
Dimensional Drawing
PCB Keyswitches
Description Photo Order no. Additional acces-
sories see page
Typical accessories RF 19 H - Short-travel keyswitch
O-ring, black, 16.0 x 1, for blocking RF 19H keys 5.30.125.007/0100 5 - 25
RF 19 H - Keyswitch, non-illuminated
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au not illuminated white - - 3.14.001.501/0000
Ag not illuminated white - - 3.14.001.506/0000
Technical data see page 4 - 72
4
RF
4 - 74 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
* The LED may be positioned either on the left-hand or
right-hand side.
Standard version: LED on left-hand side
View on component side, all hole diameters
1.1 +/- 0.1 mm
Keyswitch not illuminated
Hole Pattern RF 19 H Hole Pattern – Front Panel RF 19 H
RF 19 H - Short-travel keyswitch, fully illuminated
Contact materials Illumination Colour of lens LED colour LED type Order no.
Au fully illuminated
2 LED
red red 2 mm 3.14.002.613/0000
Au fully illuminated
2 LED
green green 2 mm 3.14.002.632/0000
Au fully illuminated
1 LED
green green super bright 3 mm 3.14.002.633/0000
Au fully illuminated
2 LED
yellow yellow 2 mm 3.14.002.653/0000
Au fully illuminated
1 LED
white white 3 mm 3.14.002.684/0000
Au fully illuminated
2 LED
orange yellow 2 mm 3.14.002.673/0000
Au fully illuminated
2 LED
white multi colour 3 mm 3.14.001.672/0000
Au fully illuminated
1 LED
blue blue 3 mm 3.14.002.683/0000
Ag fully illuminated
2 LED
red red 2 mm 3.14.002.623/0000
Ag fully illuminated
2 LED
green green 2 mm 3.14.002.642/0000
Ag fully illuminated
1 LED
green green super bright 3 mm 3.14.002.643/0000
Ag fully illuminated
1 LED
blue blue 3 mm 3.14.002.688/0000
Ag fully illuminated
2 LED
yellow yellow 2 mm 3.14.002.663/0000
Ag fully illuminated
1 LED
white white 3 mm 3.14.002.689/0000
Ag fully illuminated
2 LED
orange yellow 2 mm 3.14.002.678/0000
Ag fully illuminated
2 LED
white multi colour 3 mm 3.14.001.682/0000
Technical data see page 4 - 72
When using the keyswitches with multicolour LEDs the illumination colour can be varied from red to green by change
of polarity. Due to the frequency of the polarity-changes the colours red, green, yellow as well as all secondary colours
from these are possible.
Technical data of LED see separate page at the beginning of this chapter.
4
RF
4 - 75PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
4
RF
4 - 76 PCB Keyswitches
RF - Short-travel keyswitches
RF 19 - Signal indicator
Pict.: 0.5 x 1-module 0,5 x 2-module
1 x 1-module 1 x 2-module
Technical Data
General information
Colour of lens see order block
Recommended key grid 23/x mm
Dimensions
Length see order block
Width see order block
Overall height 9.15 mm
Mechanical design
Mounting THT soldering in PCB
Illumination see order block
LED colour see order block
LED type see order block
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Solderability / solder heat according to E DIN
resistance IEC 600 28-2-20
Wave soldering 260 °C max.
Manual soldering 350 °C / 5 sec. max.
4 - 77
4
RF
RF - Short-travel keyswitches
* The LED may be positioned either on the left-hand or right-hand side.
Standard version: LED on left-hand side
View on component side, all hole diameters 1.1 +/- 0.1 mm
Front panel cut-out = outer keyswitch size + 1 mm
Dimensional Drawing Signal Indicator RF 19
Hole Pattern RF 19
PCB Keyswitches
4
RF
4 - 78 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Housing
Lens
Illuminated area
16.4 x 7.8 mm
Pict.: 0.5 x 1-module
RF 19 - Signal indicator, ½ x 1-module
Illumination Colour of lens LED colour LED type Order no.
fully illuminated
1 LED
red red 2 mm 3.14.002.061/0000
fully illuminated
1 LED
green green 2 mm 3.14.002.062/0000
fully illuminated
1 LED
yellow yellow 2 mm 3.14.002.063/0000
fully illuminated
1 LED
orange yellow 2 mm 3.14.002.064/0000
Technical data see page 4 - 76
Technical data of LED see separate page at the beginning of chapter 4 PCB Keyswitches.
Pict.: 0,5 x 2-module
RF 19 - Signal indicator, ½ x 2-module
Illumination Colour of lens LED colour LED type Order no.
fully illuminated
3 LED
red red 2 mm 3.14.002.908/0000
fully illuminated
3 LED
green green 2 mm 3.14.002.909/0000
fully illuminated
3 LED
yellow yellow 2 mm 3.14.002.910/0000
fully illuminated
3 LED
orange yellow 2 mm 3.14.002.911/0000
Technical data see page 4 - 76
Technical data of LED see separate page at the beginning of chapter 4 PCB Keyswitches.
Pict.: 1 x 1-module
RF 19 - Signal indicator, 1 x 1-module
Illumination Colour of lens LED colour LED type Order no.
fully illuminated
2 LED
red red 2 mm 3.14.002.051/0000
fully illuminated
2 LED
green green 2 mm 3.14.002.052/0000
fully illuminated
2 LED
yellow yellow 2 mm 3.14.002.053/0000
fully illuminated
2 LED
orange yellow 2 mm 3.14.002.054/0000
fully illuminated
2 LED
blue blue 2 mm 3.14.001.659/0000
Technical data see page 4 - 76
For technical data of the LED see separate page at the beginning of chapter „RF short-travel keyswitches“
Suitable for RK 90 system design, illuminated for 2-module keycap.
Pict.: 1 x 2-module
RF 19 - Signal indicator, 1 x 2-module
Illumination Colour of lens LED colour LED type Order no.
fully illuminated
5 LED
red red 2 mm 3.14.002.071/0000
fully illuminated
5 LED
green green 2 mm 3.14.002.072/0000
fully illuminated
5 LED
yellow yellow 2 mm 3.14.002.073/0000
fully illuminated
5 LED
orange yellow 2 mm 3.14.002.074/0000
Technical data see page 4 - 76
For technical data of the LED see separate page at the beginning of chapter „RF short-travel keyswitches“
4
RF
4 - 79PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
4
RF
4 - 80 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
RF 15/19 - Special accessories
round and triangular versionsPict.: opaque light grey
Technical Data
Dimensions
Length see order block
Width see order block
Overall height see order block
Diameter see order block
Colour see order block
RF 15 N - Extension plunger, round head
Pict.: opaque light grey
Length Overall height Order no.Width Diameter Colour
- - 10 mm -9 mm 5.46.011.036/0710
- - 10 mm -9.7 mm 5.46.011.030/0710
- - 10 mm -12.5 mm 5.46.011.037/0710
- - 10 mm -13 mm 5.46.011.038/0710
- - 10 mm -22.5 mm 5.46.011.028/0710
Length of plunger = Overall height - 4.25 mm.
4
RF
4 - 81PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
RF 15 N - Extension plunger, round head, with recess for LED
Length Overall height Order no.Width Diameter Colour
- - 15 mm -9 mm 5.46.017.036/0710
- - 15 mm -9.7 mm 5.46.017.030/0710
- - 15 mm -12.5 mm 5.46.017.037/0710
- - 15 mm -22.5 mm 5.46.017.028/0710
- - 15 mm -13 mm 5.46.017.038/0710
Technical data see page 4 - 80
Length of plunger = Overall height - 4.25 mm.
RF 15 - Keycap, snap-on, for overall height 12.5 mm
Length Overall height Order no.Width Diameter Colour
14.2 mm 14.2 mm - beige12.5 mm 5.46.654.059/0227
Technical data see page 4 - 80
4
RF
4 - 82 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Spacers, round
Overlay
Front panel
Spacer
PCB
Length Overall height Order no.Width Diameter Colour
3.50 mm - - blue transparent-5.30.759.023/0000
4 mm - - green- 5.30.759.025/0000
4.25 mm - - blue- 5.30.759.026/0000
4.50 mm - - red- 5.30.759.027/0000
4.75 mm - - blue transparent-5.30.759.028/0000
5 mm - - black- 5.30.759.029/0000
5.25 mm - - yellow orange
transparent
-5.30.759.030/0000
5.50 mm - - yellow- 5.30.759.031/0000
5.75 mm - - green- 5.30.759.032/0000
6 mm - - blue- 5.30.759.033/0000
6.2 mm - - blue- 5.30.759.251/0000
6.25 mm - - red- 5.30.759.034/0000
6.50 mm - - blue transparent-5.30.759.035/0000
6.75 mm - - black- 5.30.759.036/0000
7 mm - - yellow orange
transparent
-5.30.759.037/0000
7.25 mm - - yellow- 5.30.759.038/0000
7.50 mm - - green- 5.30.759.039/0000
7.75 mm - - blue- 5.30.759.040/0000
8 mm - - red- 5.30.759.041/0000
8.25 mm - - blue transparent-5.30.759.042/0000
10.00 mm - - black- 5.30.759.043/0104
Technical data see page 4 - 80
Required spacer length = Overall height of key - front panel thickness - 0.5 mm (area embossing).
4
RF
4 - 83PCB Keyswitches Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Spacers, triangular
Countersink
from height > 4 mm
Overlay
Front panel
Spacer
PCB
Length Overall height Order no.Width Diameter Colour
2.50 mm - - blue- 5.30.759.094/0000
2.75 mm - - red- 5.30.759.095/0000
3 mm - - blue transparent-5.30.759.096/0000
3.25 mm - - black- 5.30.759.097/0000
3.50 mm - - yellow orange
transparent
-5.30.759.098/0000
3.75 mm - - yellow- 5.30.759.099/0000
4 mm - - green- 5.30.759.100/0000
4.25 mm - - blue- 5.30.759.101/0000
4.50 mm - - red- 5.30.759.102/0000
4.75 mm - - blue transparent-5.30.759.103/0000
5 mm - - black- 5.30.759.104/0000
5.25 mm - - yellow orange
transparent
-5.30.759.105/0000
5.50 mm - - yellow- 5.30.759.106/0000
5.75 mm - - green- 5.30.759.107/0000
6 mm - - blue- 5.30.759.108/0000
6.2 mm - - blue- 5.30.759.253/0000
6.25 mm - - red- 5.30.759.109/0000
6.50 mm - - blue transparent-5.30.759.110/0000
6.75 mm - - black- 5.30.759.111/0000
7 mm - - yellow orange
transparent
-5.30.759.112/0000
7.25 mm - - yellow- 5.30.759.113/0000
7.50 mm - - green- 5.30.759.114/0000
7.75 mm - - blue- 5.30.759.115/0000
4
RF
4 - 84 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RF - Short-travel keyswitches
Length Overall height Order no.Width Diameter Colour
8 mm - - red- 5.30.759.116/0000
8.25 mm - - blue transparent-5.30.759.117/0000
9 mm - - blue- 5.30.759.254/0000
10.00 mm - - black- 5.30.759.124/0000
10.25 mm - - yellow orange
transparent
-5.30.759.125/0000
Technical data see page 4 - 80
Required spacer length = Overall height of key - front panel thickness - 0.5 mm (area embossing).
RF 15 N - LED spacer
Pict.: opaque light grey
Length Overall height Order no.
Width Diameter Colour
2.2 mm -5 mm light grey12.5 mm 5.30.109.010/0756
12 mm -5 mm black22.5 mm 5.30.109.019/0105
Technical data see page 4 - 80
4
KN
19
4 - 85PCB Keyswitches
KN 19 - Short-travel main switch
General Data
Short-travel main switch for use in membrane keyboards under the overlay or with RK 90 keycaps, 250V, 4A max.
A cut-out in the overlay is not required!
Content
KN 19 - Short-travel main switch 4 - 86
KN 19 - Short-travel main switch 4 - 88
4
KN
19
4 - 86 PCB Keyswitches
KN 19 - Short-travel main switch
KN 19 - Short-travel main switch
Pict.: 1Ö + 1S 2Ö / 2S
General Data
The KN 19 makes it possible to implement a power switch directly in a low-profile data entry system. This eliminates the
need for extra switches on the device and additional openings in the overlay. In this way, you can achieve an optimum
of safety and a consistent design.
The contact opening widths comply with the VDE standards. The KN 19 can also be employed underneath RK 90
keycaps. Other actuation functions (momentary, latching/momentary) available on request.
Technical Data
General information
Recommended key grid 19.05 x 38.1 mm
Dimensions
Length 37.8 mm
Width 18.8 mm
Overall height 9.7 mm
Mechanical design
Mounting on PCB
Terminals THT solder terminals
Contact system snap-action bridge
contact
Contact arrangement see order block
Contact materials Ag
Illumination 1 LED (max. 3 mm)
possible
Degree of protection IP40
Hot wire ignition acc. to 850 °C
IEC 60695-2-1
Mechanical characteristics
Operating force max. 9±3 N
Operating travel 0.55±0.15 mm
Robustness max. 100 N
Electrical characteristics
Rated voltage AC min. 12 V
Rated voltage DC min. 12 V
Rated voltage AC max. 250 V
Rated voltage DC max. 50 V
Ohmic load AC 6 A
Ohmic load DC min. 0.1 A
Ohmic load DC max. 10 A
Contact resistance when new 50 mE
max.
Capacity input current AC max. 100 A
Rated motor current AC 4 A
Rated filament lamp current AC 2.4 A
Bouncing time max. 10 ms
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life AC AC 250 V: 200.000/
2A; 100.000 /6A
Operating life DC 50,000(10 A / 50 V=)
Soldering time max. 3 s
Soldering temperature max. 350 °C
Flame class acc. to UL 94 UL 94 VO
Definition "ON" "OFF" only
valid for 2-pole version.
4 - 87
4
KN
19
KN 19 - Short-travel main switch
1 Ö + 1 S 2 Ö/2 S
Locating hole only version 2 NO/2 NC
View on component side.
Circuit Diagram
Dimensional Drawing Hole Pattern
Approvals
IEC 61058 UL 508,C22.2 No.
14-M91
PCB Keyswitches
4
KN
19
4 - 88 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
KN 19 - Short-travel main switch
Approvals
IEC 61058 UL 508,C22.2 No.
14-M91
Description Photo Order no. Additional acces-
sories see page
Typical accessories KN 19 - Short-travel main switch
KN19 - Absorption rubber 5.30.729.009/0000
Pict.: 1 NC + 1 NO
KN 19 - Short-travel main switch
Contact arrangement Rated voltage AC max. Order no.
1 NC + 1 NO 250 V 1.12.000.001/0000
2 NC / 2 NO 250 V 1.12.000.501/0000
Technical data see page 4 - 86
Accessoires:
KN19 - Absorption rubber: 5.30.729.009/0000
For keycaps, refer to RK 90 system design.
Positive opening NC contacts to IEC 60 947-5-1.
1-LED spot-illumination (max. 3 mm) possible.
4
RK
90
4 - 89PCB Keyswitches
RK 90 - Keycaps
General Data
Keycaps for RACON, RF 15 / RF 19 and KN 19 short-travel keyswitches
s9OUCANINSERTALEGENDINSERTBETWEENLENSANDPRESSUREPAOLOFTHETRANSPARENTKEYCAPS
Content
RK 90 - Keycaps, plastic, 9 x 9 mm 4 - 92
2++EYCAPBODYPLASTICFORLENSESXMM 
RK 90 - Keycaps, plastic, 14 mm 4 - 94
2++EYCAPBODYPLASTICFORLENSESMMMODULE 
2++EYCAPBODYPLASTICFORLENSESMODULE 
2++EYCAPBODYPLASTICFORLENSESMMMODULE 
2++EYCAPBODYPLASTICFORLENSESMODULE 
RK 90 - Keycaps, aluminum, 14 x 14 mm 4 - 98
2++EYCAPSALUMINUMMMMODULE 
2++EYCAPSALUMINUMMMMODULE 
2++EYCAPSALUMINUMMMMODULE 
RK 90 - Special accessories 4 - 100
2+&INTOAVOIDINADVERTENTOPERATION 
2+3PACER- 
2+3ILICONEFOILXXMM 
4
4 - 90 PCB Keyswitches
RK
90
Example with RF 15 keyswitches. Instead of RF 15
following keyswitches can be used:
- MICON 5
- RACON 8/12
- RF 15 keyswitches and signal indicators
- RF 19 keyswitches and signal indicators
- Short-travel main switch KN 19
The RK 90 system was granted the prize of the Design
Forum of the Hannover Fair.
Degree of protection: IP65 according to DIN in front of the
panel, with silicone sealing.
Mounting from front
Sealing foil between RK 90 keyboard and customer’s front
panel.
Mounting from rear
Sealing foil is screwed to RK 90 panel with fixing rails;
sealing between keyboard and customer’s front panel has
to be provided.
As the legending is protected by the lens, it is friction-
proof.
L Engraving: With this method the keycaps are engraved
with the required symbol and then inlaid with ink.
L Laser printing: This labelling method is possible for
opaque keycaps. The symbols are engraved in the
keycaps with laser.
L When using transparent lenses, the pressure pad can
be legended by printing.
Keycap system RK 90
Installation methods
Legending
RK 90 - Keycaps
4
PCB Keyswitches 4 - 91
RK
90
L Silicone sealing:
Material: Silicone transparent
Type: A-SY 40-79
Hardness: 30° shore +/- 5°
Thickness: 0.45 +/- 0.05 mm
L Installation: Ensure that the keyboard slopes slightly so
that any liquid can drain away between front panel and
silicone sealing; if necessary, provide additional drain
holes in the front panel.
L Front panel thickness:
- Aluminum: 2 mm (1.5 mm min, 3 mm max.)
(Fixing with M 3 pressed-in studs)
- Steel: 2 mm (3 mm max.): V2A: 1.25 mm
(Fixing with M 3 welded-on studs)
The keytop surface is flush with the keyboard at a
panel thickness of 3.5 mm.
Recommendations
For the cleaning of the plastic keycaps please do not use
cleaning liquids based on alcohol or acid.
Cleaning liquids
RK 90 - Keycaps
4
RK
90
 PCB Keyswitches
RK 90 - Keycaps
RK 90 - Keycaps, plastic, 9 x 9 mm
Steel stud welded-on with steel version
pressed-in with aluminum version Keycap
Front panel
Sealing
Housing
0ICTWITHCOLOURLESSLENS
General Data
9OUCANDESIGNESPECIALLYSMALLINPUTFIELDSWITHTHESMALLKEYCAPXMM&OREXAMPLECONTROLSFORMEASUREMENT
ANDLABORATORYEQUIPMENTWHICHDONOTOFFERMUCHSPACEFORINPUTFIELDSBECAUSEOFTHEIRSMALLSIZE2+KEYCAPS
XMMAND2!#/.SHORTTRAVELKEYSWITCHESCANBEUSEDTOIMPLEMENTKEYGRIDSOFONLYMM4HEKEYCAPSCAN
BELEGENDEDBYLASERPRINTINGENGRAVINGORSTANDARDPRINTING
4HISKEYCAPISOURFIRSTCHOICEINACOMBINATIONWITHTHEILLUMINATED2!#/.ISHORTTRAVELKEYSWITCH
Please note: &ORTHECLEANINGOFTHEPLASTICKEYCAPSPLEASEDONOTUSECLEANINGLIQUIDSBASEDONALCOHOLORACID
Technical Data
General information
#OLOUROFLENS SEEORDERBLOCK
3IZE MODULE
$EGREEOFPROTECTION )0
WITHSILICONSEAL
)LLUMINABILITY SEEORDERBLOCK
Dimensions
$IMENSIONKEYCAPINFRONTOF XMM
FRONTPANEL
$IMENSIONKEYCAPBEHIND XMM
FRONTPANEL
$IMENSIONCHOLEPATTERNS XMM
FINALSIZE
$IMENSIONHOLEPATTERNS XMM
PUNCHEDSIZE
0LEASEORDERLENSSEPARATELY
4
RK
90

RK 90 - Keycap body plastic, for lenses 9 x 9 mm
Final size
Punched size
0ICTWITHLENSLIGHTGREY
Size Illuminability Dimension
keycap behind
front panel
Order no.
without lens
NoteDimension (c)
hole patterns
final size
Dimension
keycap in front
of front panel
MODULE yes XMM X
MM
X
MM
 0LEASEORDERLENSES
SEPARATELY
4ECHNICALDATASEEPAGE
Stock itemsAREMARKED
BYbold printed order numbers.
PCB Keyswitches
Lenses:
2+,ENSXMMOPAQUERED
2+,ENSXMMOPAQUEYELLOW
2+,ENSXMMOPAQUEGREEN
2+,ENSXMMOPAQUEBLUE
2+,ENSXMMOPAQUELIGHTGREY
2+,ENSXMMTRANSPARENTCOLOURLESS
2+,ENSXMMTRANSPARENTRED
2+,ENSXMMTRANSPARENTYELLOW
2+,ENSXMMTRANSPARENTGREEN
RK 90 - Keycaps
4
RK
90
4 - 94 PCB Keyswitches
RK 90 - Keycaps
RK 90 - Keycaps, plastic, 14 mm
0ICTWITHLENSOPAQUEGREEN
General Data
+EYCAPSYSTEMFORMMGRID4HEKEYCAPSCANBELEGENDEDBYLASERPRINTINGENGRAVINGORSTANDARDPRINTING
+EYCAPSSETSWITHLEGENDSANDOTHERKEYCAPSHAPESCOLOURSAVAILABLEONREQUEST
Please note: &ORTHECLEANINGOFTHEPLASTICKEYCAPSPLEASEDONOTUSECLEANINGLIQUIDSBASEDONALCOHOLORACID
Technical Data
General information
#OLOUROFLENS SEEORDERBLOCK
3IZE SEEORDERBLOCK
$EGREEOFPROTECTION )0
WITHSILICONSEAL
)LLUMINABILITY yes
Dimensions
$IMENSIONBINFRONTOF SEEORDERBLOCK
FRONTPANEL
$IMENSIONABEHINDFRONT SEEORDERBLOCK
PANEL
$IMENSIONCHOLEPATTERNS SEEORDERBLOCK
FINALSIZE
$IMENSIONHOLEPATTERNS SEEORDERBLOCK
PUNCHEDSIZE
4
RK
90
4 - 95PCB Keyswitches Stock items are marked
by bold printed order numbers.
RK 90 - Keycaps
RK 90 - Keycap body plastic, for lenses 14 mm, 1-module
Final size
Punched size
Pict.: with lens, opaque green
Size Illuminability Dimension (a)
behind front
panel
Order no.
without lens
NoteDimension (c)
hole patterns
final size
Dimension (b)
in front of front
panel
1-module yes 17.20 x 17.20
mm
14.00 x 14.00
mm
13.85 x 13.85
mm
5.55.103.030/1013 Please order lenses
separately.
Technical data see page 4 - 94
RK 90 - Keycap body plastic, for lenses 1¼-module
Final size
Punched size
Size Illuminability Dimension (a)
behind front
panel
Order no.
without lens
NoteDimension (c)
hole patterns
final size
Dimension (b)
in front of front
panel
1 1¼-module yes 17.20 x 20.7
mm
14,00 x 17,5
mm
13.85 x 17.35
mm
5.55.103.031/1013 Please order lenses
separately.
Technical data see page 4 - 94
Lenses:
RK 90 - Lens, 14 mm, 1-module, opaque red: 5.46.681.001/0309
RK 90 - Lens, 14 mm, 1-module, opaque yellow: 5.46.681.001/0409
RK 90 - Lens, 14 mm, 1-module, opaque green: 5.46.681.001/0514
RK 90 - Lens, 14 mm, 1-module, opaque blue: 5.46.681.001/0611
RK 90 - Lens, 14 mm, 1-module, opaque light grey: 5.46.681.001/0700
RK 90 - Lens, 14 mm, 1-module, transparent colourless: 5.46.681.021/1002
RK 90 - Lens, 14 mm, 1-module, transparent red: 5.46.681.021/1307
RK 90 - Lens, 14 mm, 1-module, transparent yellow: 5.46.681.021/1403
RK 90 - Lens, 14 mm, 1-module, transparent green: 5.46.681.021/1510
Lenses:
RK 90 - Lens, 14 mm, 1.25-module, opaque red: 5.46.681.002/0309
RK 90 - Lens, 14 mm, 1.25-module, opaque light grey: 5.46.681.002/0700
RK 90 - Lens, 14 mm, 1.25-module, transparent colourless: 5.46.681.022/1002
RK 90 - Lens, 14 mm, 1.25-module, transparent red: 5.46.681.022/1307
RK 90 - Lens, 14 mm, 1.25-module, transparent yellow: 5.46.681.022/1403
RK 90 - Lens, 14 mm, 1.25-module, transparent green: 5.46.681.022/1510
4
RK
90
4 - 96 Stock items are marked
by bold printed order numbers.
PCB Keyswitches
RK 90 - Keycap body plastic, for lenses 2-module
Final size
Punched size
Pict.: with lens, transparent yellow
Size Illuminability Dimension (a)
behind front
panel
Order no.
without lens
NoteDimension (c)
hole patterns
final size
Dimension (b)
in front of front
panel
2-module yes 17.20 x 31.20
mm
14.00 x 28.00
mm
13.85 x 27.85
mm
5.55.103.077/1013 Please order lenses
separately.
Technical data see page 4 - 94
Lenses:
RK 90 - Lens, 14 mm, 2-module, opaque red: 5.46.681.004/0309
RK 90 - Lens, 14 mm, 2-module, opaque yellow: 5.46.681.004/0409
RK 90 - Lens, 14 mm, 2-module, opaque green: 5.46.681.004/0514
RK 90 - Lens, 14 mm, 2-module, opaque blue: 5.46.681.004/0611
RK 90 - Lens, 14 mm, 2-module, opaque light grey: 5.46.681.004/0700
RK 90 - Lens, 14 mm, 2-module, transparent colourless: 5.46.681.024/1002
RK 90 - Lens, 14 mm, 2-module, transparent red: 5.46.681.024/1307
RK 90 - Lens, 14 mm, 2-module, transparent yellow: 5.46.681.024/1403
RK 90 - Lens, 14 mm, 2-module, transparent green: 5.46.681.024/1510
RK 90 - Keycap body plastic, for lenses 14 mm, 1½-module
Final size
Punched size
Pict.: with lens, opaque light grey
Size Illuminability Dimension (a)
behind front
panel
Order no.
without lens
NoteDimension (c)
hole patterns
final size
Dimension (b)
in front of front
panel
1½-module yes 17.20 x 24.20
mm
14.00 x 21.00
mm
13.85 x 20.85
mm
5.55.103.032/1013 Please order lenses
separately.
Technical data see page 4 - 94
Lenses:
RK 90 - Lens, 14 mm, 1.5-module, opaque red: 5.46.681.003/0309
RK 90 - Lens, 14 mm, 1.5-module, opaque yellow: 5.46.681.003/0409
RK 90 - Lens, 14 mm, 1.5-module, opaque green: 5.46.681.003/0514
RK 90 - Lens, 14 mm, 1.5-module, opaque blue: 5.46.681.003/0611
RK 90 - Lens, 14 mm, 1.5-module, opaque light grey: 5.46.681.003/0700
RK 90 - Lens, 14 mm, 1.5-module, transparent colourless: 5.46.681.023/1002
RK 90 - Lens, 14 mm, 1.5-module, transparent red: 5.46.681.023/1307
RK 90 - Lens, 14 mm, 1.5-module, transparent yellow: 5.46.681.023/1403
RK 90 - Lens, 14 mm, 1.5-module, transparent green: 5.46.681.023/1510
RK 90 - Keycaps
4
RK
90
4 - 98 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RK 90 - Keycaps
RK 90 - Keycaps, aluminum, 14 x 14 mm
0ICTNATURALANODIZED
General Data
4HE2+SYSTEMDESIGNWITHMETALKEYCAPSISFAIRLYSAFEAGAINSTMECHANICALTHERMALORCHEMICALEFFECTS#OMBINED
WITHAMETALFRONTPANELTHISDATAENTRYSYSTEMOFFERSMAXIMUMPROTECTIONAGAINSTVANDALISM4RIEDANDTESTED-)#/.
2!#/.OR2&0#"KEYSWITCHESAREUSEDUNDERNEATHTHEMETALKEYCAPS
4HEKEYCAPSCANBEPROVIDEDWITHENGRAVEDCOLOUREDANODIZEDORLASERPRINTEDLEGENDS4HISMEANSTHATTHELEGENDIS
DURABLEANDCANNOTBEREMOVEDBYMECHANICALORCHEMICALMEANS
Technical Data
General information
#OLOUROFLENS ALUMINUMCOLOURLESS
ANODIZED
3IZE SEEORDERBLOCK
$EGREEOFPROTECTIONWITH )0
SILICONSEAL
Dimensions
$IMENSIONBINFRONTOF SEEORDERBLOCK
FRONTPANEL
$IMENSIONABEHINDFRONT SEEORDERBLOCK
PANEL
$IMENSIONCHOLEPATTERNS SEEORDERBLOCK
FINALSIZE
$IMENSIONHOLEPATTERNS SEEORDERBLOCK
PUNCHEDSIZE
RK 90 - Keycaps, aluminum, 14 mm, 1-module
13.85
18.35
2.80
b
a
c
1.80
0ICTNATURALANODIZED
Size Colour of lens Dimension (a) behind
front panel
Dimension (b) in
front of front panel
Dimension (c) hole
patterns final size
Order no.
MODULE ALUMINUMCO-
LOURLESSANODIZED
XMM XMM XMM 
4
RK
90
4 - 99PCB Keyswitches Stock itemsAREMARKED
BYbold printed order numbers.
RK 90 - Keycaps
RK 90 - Keycaps, aluminum, 14 mm, 1½-module
13.85
18.35
2.80
b
a
c
1.80
Size Colour of lens Dimension (a) behind
front panel
Dimension (b) in
front of front panel
Dimension (c) hole
patterns final size
Order no.
MODULE ALUMINUMCO-
LOURLESSANODIZED
XMM XMM XMM 
4ECHNICALDATASEEPAGE
RK 90 - Keycaps, aluminum, 14 mm, 2-module
13.85
18.35
2.80
b
a
c
1.80
Size Colour of lens Dimension (a) behind
front panel
Dimension (b) in
front of front panel
Dimension (c) hole
patterns final size
Order no.
MODULE ALUMINUMCO-
LOURLESSANODIZED
XMM XMM XMM 
4ECHNICALDATASEEPAGE
4
RK
90
 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RK 90 - Keycaps
RK 90 - Special accessories
0ICTCHARCOALGREY
Technical Data
General information
#OLOUR SEEORDERBLOCK
Dimensions
$IMENSIONS SEEORDERBLOCK
RK 90 - Fin, to avoid inadvertent operation
Mounting holes
0ICTCHARCOALGREY
Order no.Short text Feature 1 Feature 2
2+&INTOAVOIDINADVERTENTOPERATIONLIGHTGREY - - 
2+&INTOAVOIDINADVERTENTOPERATIONCHARCOALGREY - - 5.55.103.079/0152
4
RK
90
PCB Keyswitches Stock itemsAREMARKED
BYbold printed order numbers.
RK 90 - Keycaps
RK 90 - Spacer M 4
Order no.Short text Feature 1 Feature 2
2+3PACER-WITH2&KEYSHEIGHTMM
MOUNTINGFROMFRONTPCPERSTUD
-MMOVERALLHEIGHT
FOR2&

2+3PACER-WITH2&KEYSHEIGHTMM
MOUNTINGFROMREARPCPERSTUD
-MMOVERALLHEIGHT
FOR2&

2+3PACER-WITH2&.KEYSHEIGHTMM
MOUNTINGFROMREARPCPERSTUD
-MMOVERALLHEIGHT
FOR2&.

2+3PACER-WITH2!#/.KEYSHEIGHTMM
MOUNTINGFROMFRONTPCPERSTUD
-MMOVERALLHEIGHTFOR
2!#/.

2+3PACER-WITH2!#/.KEYSHEIGHTMM
MOUNTINGFROMREARPCPERSTUD
-MMOVERALLHEIGHT
FOR2!#/.

4ECHNICALDATASEEPAGE
RK 90 - Silicone foil 600 x 590 x 0.45 mm
Order no.Short text Feature 1 Feature 2
2+3ILICONEFOILXXMM TRANSPARENT XX
MM

4ECHNICALDATASEEPAGE
4
RG
85 III
4 - 103PCB Keyswitches
RG 85 III - Short-travel system
General Data
Vandal-proof input system, ideally suited for elevator controls, info terminals, vending machines, etc.
s%DGEILLUMINATIONANDSYMBOLILLUMINATIONPOSSIBLE
s#ONNECTION%ACHMODULEINDIVIDUALLYWITHANPIN-ICRO-ATCHSOCKETCONNECTOR
s-ODULARFIXINGSYSTEMWITHQUICKFASTENERSORSINGLEFIXING
s#ONTACTARRANGEMENT./CONTACTOR.#./CONTACT
s6M!MAX
s$EGREEOFPROTECTION)0KEYLOCKSWITCH)0
Content
RG 85 III - Keyswitch 4 - 106
2')))+EYSWITCHROUNDDESIGNWITHOUTLENS 
2')))+EYSWITCHSQUAREDESIGNWITHOUTLENS 
RG 85 III - Keylock switch 4 - 110
2')))+EYLOCKSWITCHROUNDDESIGNWITHOUTLENS 
2')))+EYLOCKSWITCHSQUAREDESIGNWITHOUTLENS 
RG 85 III - Signal indicator, without lens 4 - 114
2')))3IGNALINDICATORWITHOUTLENS 
RG 85 III - Accessories 4 - 116
2'))),ENSESFORKEYSWITCHESROUND 
2'))),ENSESFORKEYSWITCHESSQUARE 
2'))),ENSESFORKEYLOCKSWITCHESROUND 
2'))),ENSESFORKEYLOCKSWITCHESSQUARE 
2'))),ENSROUNDFORSIGNALINDICATORS 
2'))),ENSSQUAREFORSIGNALINDICATORS 
2'))),ENSTRIANGULARFORSIGNALINDICATORS 
#ABLEWIRESWITHSOCKETCONNECTORSONBOTHENDS 
&IXINGRAILLENGTHMM 
3PACER 
&IXINGPIECEFORMOUNTINGTHEELEMENTSWITHTHERAILFIXINGMETHOD 
4 - 104 PCB Keyswitches
4
RG
85 III
RG 85 III - Short-travel system
System Features
Perfectly suited for: elevator controls, info terminals,
vending machines, etc.
L Vandal proof construction
L Modular fixing system with quick fasteners or single
fixing method using thread studs
L Connection with keyed 8-pin micro-match connector
L Degree of protection: IP40/65
Keylock Switch Features
L Round or square design and lens shape
L Edge illumination in one or two colours with 4 LED for
each colour
L Lens material: Aluminum or stainless steel with plastic
inlays
L Contact arrangement: 1 NO
L Cylinder lock with pin tumblers
L Two switching positions: 0 and 90 degrees, key can be
removed in any position
L Lock type 5201 – other lock types on request
L Included: 2 keys
Signal Indicator Features
L Lens shape round, square or triangular (arrow shape)
L Lens material: Translucent plastic material
L Fully illuminated with 5 LED
Micro-Match Connector Pin Assignment
1/3 NO contact
2 O V – LED
4 Edge illuminat./signal indicator
1st colour + 24 V DC +/- 20%
5 Symbol illumination
+ 24 V DC +/- 20%
6 Edge illuminat./signal indicator
2nd colour + 24 V DC +/- 20%
7/8 NC contact
Pushbutton Features
L Round or square design and lens shape
L Edge illumination in one or two colours with 4 LED for
each colour
L Pushbutton with 1 NO contact: Additional illumination
of the symbol with 2 LED possible
L Lens material: Aluminum or stainless steel with plastic
inlays
L Switching element: short-travel keyswitch RF 19
- 1 NO contact, non-illuminated
- 1 NO contact, fully illuminated
- 1 NC contact and 1 NO contact, non-illuminated
PCB Keyswitches 4 - 105
4
RG
85 III
RG 85 III - Short-travel system
Rail fixing method Single fixing method
Fixing rail
5.41 032.173
Threaded studs
M4 (min.) 14 mm
Fixing element
5.41 032.173
Grid 35.00
Grid 55.00(27.50) (27.50)
15.24 ± 0.10
27.38 ± 0.10
12.08 2.00
Distance
threaded studs
55.00 ± 0.10
Distance
threaded studs
55.00 ± 0.10
7.25 ± 0.05
Grid 35.00
15.24 ± 0.10
Grid 55.00
Distance
threaded studs
55.00 ± 0.10
Distance
threaded studs
55.00 ± 0.10
Threaded studs
M4 x (min.) 20 mm
Spacer
5.30 163.024
Installation plan
Front panel
4
RG
85 III
 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Keyswitch
Technical Data
Dimensions
-OUNTINGGRIDMIN XMM
,ENGTH MM
7IDTH MM
Mechanical design
6ERSION SEEORDERBLOCK
-OUNTING ON5RAILSORSINGLE
MOUNTING
4ERMINALS PIN-ICRO
-ATCHFEMALE
CONNECTOR
#ONTACTSYSTEM SNAPACTION./
ORBRIDGECONTACT
.#./
#ONTACTARRANGEMENT SEEORDERBLOCK
#ONTACTMATERIALS !G
3YMBOLILLUMINATION SEEORDERBLOCK
%DGEILLUMINATION SEEORDERBLOCK
Mechanical characteristics
/PERATINGFORCE .
/PERATINGTRAVEL MM
3WITCHINGTRAVEL./ MM
3WITCHINGTRAVEL.# MM
Electrical characteristics
2ATEDVOLTAGEMIN 6
2ATEDVOLTAGEMAX 6
2ATEDCURRENTMIN M!
2ATEDCURRENTMAX M!
2ATEDPOWERMAX 7
#ONTACTRESISTANCEWHENNEW ME
MAX
#ONTACTRESISTANCEACCTO 3 E
LIFEMAX
"OUNCINGTIMEMAX MS
/PERATINGVOLTAGEFOR,%$ ¢6
)NPUTCURRENT,%$ PERCOLOUR,%$ROW
M!
Other specifications
!MBIENTTEMPOPERATINGMIN ª#
!MBIENTTEMPOPERATINGMAX ª#
3TORAGETEMPERATUREMIN ª#
3TORAGETEMPERATUREMAX ª#
%NVIRONMENTALRESTISTANCE ACCTO)%#
AND
/PERATINGLIFEMIN 
OPERATIONS
$EGREEOFPROTECTIONRAIL )0
MOUNTING
$EGREEOFPROTECTIONSINGLE )0
MOUNTING
&LAMMABILITYOFMATERIALS ACCORDINGTO5,("
Description Photo Order no. Additional acces-
sories see page
Typical accessories RG 85 III - Keyswitch
#ABLEWIRESWITHSOCKETCONNECTORSONBOTHENDS
LENGTHM
 
2'))),ENSESFORKEYSWITCHESROUNDSTAINLESSSTEEL  
2'))),ENSESFORKEYSWITCHESSQUAREALUMINUM  
4
RG
85 III
PCB Keyswitches Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Keyswitch, round design, without lens
Contact arrangement Symbol illumination Order no.Edge illumination Version
./ ,%$WHITE ROUND-
./ ,%$RED ROUND-
./ ,%$YELLOW ROUND-
./ ,%$GREEN ROUND-
./ ,%$BLUE ROUND-
./ ,%$WHITE,%$BLUE ROUND-
./ ,%$GREEN,%$RED ROUND-
./ ,%$WHITE ROUND,%$YELLOW 
./ ,%$RED ROUND,%$RED 
./ ,%$YELLOW ROUND,%$GREEN 
./ ,%$GREEN ROUND,%$GREEN 
./ ,%$BLUE ROUND,%$BLUE 
./ ,%$WHITE,%$BLUE ROUND,%$BLUE 
./ ,%$GREEN,%$RED ROUND,%$RED 
.#./ ,%$WHITE ROUND-
.#./ ,%$RED ROUND-
.#./ ,%$YELLOW ROUND-
.#./ ,%$GREEN ROUND-
.#./ ,%$BLUE ROUND-
.#./ ,%$WHITE,%$BLUE ROUND-
.#./ ,%$GREEN,%$RED ROUND-
4ECHNICALDATASEEPAGE
0LEASEORDERLENSESROUNDSHAPESEPARATELY
4
RG
85 III
 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Keyswitch, square design, without lens
Contact arrangement Symbol illumination Order no.Edge illumination Version
./ ,%$WHITE SQUARE-
./ ,%$RED SQUARE-
./ ,%$YELLOW SQUARE-
./ ,%$GREEN SQUARE-
./ ,%$BLUE SQUARE-
./ ,%$WHITE,%$BLUE SQUARE-
./ ,%$GREEN,%$RED SQUARE-
./ ,%$WHITE SQUARE,%$YELLOW 
./ ,%$RED SQUARE,%$RED 
./ ,%$YELLOW SQUARE,%$GREEN 
./ ,%$GREEN SQUARE,%$GREEN 
./ ,%$BLUE SQUARE,%$BLUE 
./ ,%$WHITE,%$BLUE SQUARE,%$BLUE 
./ ,%$GREEN,%$RED SQUARE,%$RED 
.#./ ,%$WHITE SQUARE-
.#./ ,%$RED SQUARE-
.#./ ,%$YELLOW SQUARE-
.#./ ,%$GREEN SQUARE-
.#./ ,%$BLUE SQUARE-
.#./ ,%$WHITE,%$BLUE SQUARE-
.#./ ,%$GREEN,%$RED SQUARE-
4ECHNICALDATASEEPAGE
0LEASEORDERLENSESSQUARESHAPESEPARATELY
4
RG
85 III
4 - 110 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Keylock switch
Technical Data
Dimensions
-OUNTINGGRIDMIN XMM
,ENGTH MM
7IDTH MMMMWITH
SEALING
-OUNTINGDEPTH SEEORDERBLOCK
Mechanical design
6ERSION SEEORDERBLOCK
-OUNTING ON5RAILSORSINGLE
MOUNTING
4ERMINALS PIN-ICRO-ATCH
FEMALE
CONNECTOR
#ONTACTSYSTEM CROSSCONTACT
#ONTACTARRANGEMENT ./
#ONTACTMATERIALS !UALLOY
3YMBOLILLUMINATION NONE
%DGEILLUMINATION SEEORDERBLOCK
,OCK CYLINDERLOCKLOCK
TYPE
+EYREMOVALPOSITION 0OS
Mechanical characteristics
2OTATINGANGLE Xª
3WITCHINGTRAVEL./ MM
3WITCHINGTRAVEL.# SEEORDERBLOCK
Electrical characteristics
2ATEDVOLTAGEMIN 6
2ATEDVOLTAGEMAX 6
2ATEDCURRENTMIN M!
2ATEDCURRENTMAX M!
2ATEDPOWERMAX 1 W
#ONTACTRESISTANCEWHENNEW ME
MAX
#ONTACTRESISTANCEACCTO 3 E
LIFEMAX
"OUNCINGTIMEMAX MS
/PERATINGVOLTAGEFOR,%$ ¢6
)NPUTCURRENT,%$ PERCOLOUR,%$ROW
M!
Other specifications
!MBIENTTEMPOPERATINGMIN ª#
!MBIENTTEMPOPERATINGMAX ª#
3TORAGETEMPERATUREMIN ª#
3TORAGETEMPERATUREMAX ª#
%NVIRONMENTALRESTISTANCE ACCTO)%#
AND
/PERATINGLIFEMIN 
OPERATIONS
$EGREEOFPROTECTIONRAIL )0
MOUNTING
$EGREEOFPROTECTIONSINGLE )0
MOUNTING
&LAMMABILITYOFMATERIALS ACCORDINGTO5,("
Description Photo Order no. Additional acces-
sories see page
Typical accessories RG 85 III - Keylock switch
2'))),ENSESFORKEYLOCKSWITCHESROUND
STAINLESSSTEEL
 
2'))),ENSESFORKEYLOCKSWITCHESSQUAREALUMINUM  
4
RG
85 III
4 - 111PCB Keyswitches Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Keylock switch, round design, without lens
Contact arrangement Rotating angle Order no.Edge illumination Version
./ ,%$WHITE ROUNDXª 3.99.400.141/2000
./ ,%$RED ROUNDXª 3.99.400.141/3000
./ ,%$YELLOW ROUNDXª 
./ ,%$GREEN ROUNDXª 
./ ,%$BLUE ROUNDXª 3.99.400.141/6000
./ ,%$WHITE,%$BLUE ROUNDXª 
./ ,%$GREEN,%$RED ROUNDXª 
4ECHNICALDATASEEPAGE
Accessoires:
2'))),ENSESFORKEYLOCKSWITCHESROUNDSTAINLESSSTEEL
0LEASEORDERLENSESROUNDSHAPESEPARATELY
4
RG
85 III
 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Keylock switch, square design, without lens
Contact arrangement Rotating angle Order no.Edge illumination Version
./ ,%$WHITE SQUAREXª 
./ ,%$RED SQUAREXª 
./ ,%$YELLOW SQUAREXª 
./ ,%$GREEN SQUAREXª 
./ ,%$BLUE SQUAREXª 
./ ,%$WHITE,%$BLUE SQUAREXª 
./ ,%$GREEN,%$RED SQUAREXª 
4ECHNICALDATASEEPAGE
Accessoires:
2'))),ENSESFORKEYLOCKSWITCHESSQUARESTAINLESSSTEEL
0LEASEORDERLENSESSQUARESHAPESEPARATELY
4
RG
85 III
4 - 114 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Signal indicator, without lens
Technical Data
Dimensions
-OUNTINGGRIDMIN XMM
,ENGTH MM
7IDTH MM
Mechanical design
6ERSION ACCORDINGTOLENS
-OUNTING ON5RAILSORSINGLE
MOUNTING
4ERMINALS PIN-ICRO-ATCH
FEMALE
CONNECTOR
)LLUMINATION SEEORDERBLOCK
Electrical characteristics
/PERATINGVOLTAGEFOR,%$ ¢6
)NPUTCURRENT,%$ DEPENDINGON,%$
COLOURM!
Other specifications
!MBIENTTEMPOPERATINGMIN ª#
!MBIENTTEMPOPERATINGMAX ª#
3TORAGETEMPERATUREMIN ª#
3TORAGETEMPERATUREMAX ª#
%NVIRONMENTALRESTISTANCE ACCTO)%#
AND
$EGREEOFPROTECTIONRAIL )0
MOUNTING
$EGREEOFPROTECTIONSINGLE )0
MOUNTING
&LAMMABILITYOFMATERIALS ACCORDINGTO5,("
Description Photo Order no. Additional acces-
sories see page
Typical accessories RG 85 III - Signal indicator, without lens
#ABLEWIRESWITHSOCKETCONNECTORSONBOTHENDS
LENGTHM
 
2'))),ENSSQUAREFORSIGNALINDICATORS  
2'))),ENSROUNDFORSIGNALINDICATORS  
2'))),ENSTRIANGULARFORSIGNALINDICATORS 5.04.903.011/0000 
4
RG
85 III
PCB Keyswitches Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Signal indicator, without lens
Illumination Order no.
,%$WHITE 
,%$RED 
,%$YELLOW 
,%$GREEN 
,%$BLUE 
,%$WHITE,%$BLUE 
,%$GREEN,%$RED 
4ECHNICALDATASEEPAGE
0LEASEORDERROUNDSQUAREORTRIANGULARLENSESSEPARATELY
4
RG
85 III
 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Accessories
RG 85 III - Lenses for keyswitches, round
Version Legending colour Order no.Form of lens Legending
ALUMINUM ROUND -- 
ALUMINUM ROUND 1OPAQUEBLACK 
ALUMINUM ROUND 1TRANSLUCENTWHITE 
ALUMINUM ROUND OPAQUEBLACK 
ALUMINUM ROUND TRANSLUCENTWHITE 
ALUMINUM ROUND 3OPAQUEBLACK 
ALUMINUM ROUND 3TRANSLUCENTWHITE 
ALUMINUM ROUND 4OPAQUEBLACK 
ALUMINUM ROUND 4TRANSLUCENTWHITE 
ALUMINUM ROUND OPAQUEBLACK 
ALUMINUM ROUND TRANSLUCENTWHITE 
ALUMINUM ROUND OPAQUEBLACK 
ALUMINUM ROUND TRANSLUCENTWHITE 
ALUMINUM ROUND 5OPAQUEBLACK 
ALUMINUM ROUND 5TRANSLUCENTWHITE 
4
RG
85 III
PCB Keyswitches Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
Version Legending colour Order no.Form of lens Legending
ALUMINUM ROUND KOPAQUEBLACK 
ALUMINUM ROUND KTRANSLUCENTWHITE 
ALUMINUM ROUND %OPAQUEBLACK 
ALUMINUM ROUND %TRANSLUCENTWHITE 
ALUMINUM ROUND SYMBOLuBELLhOPAQUEYELLOW 
ALUMINUM ROUND SYMBOLuOPENDOORhOPAQUEBLACK 
ALUMINUM ROUND SYMBOLuOPENDOORhTRANSLUCENTWHITE 
ALUMINUM ROUND SYMBOLuCLOSEDOORhOPAQUEBLACK 
ALUMINUM ROUND SYMBOLuCLOSEDOORhTRANSLUCENTWHITE 
ALUMINUM ROUND SYMBOLuVENTILATORhOPAQUEBLACK 
ALUMINUM ROUND SYMBOLuVENTILATORhTRANSLUCENTWHITE 
ALUMINUM ROUND SYMBOLuARROWhOPAQUEBLACK 
ALUMINUM ROUND SYMBOLuARROWhTRANSLUCENTWHITE 
STAINLESSSTEEL ROUND -- 
STAINLESSSTEEL ROUND 1OPAQUEBLACK 
STAINLESSSTEEL ROUND 1TRANSLUCENTWHITE 
STAINLESSSTEEL ROUND OPAQUEBLACK 
STAINLESSSTEEL ROUND TRANSLUCENTWHITE 
STAINLESSSTEEL ROUND 3OPAQUEBLACK 
STAINLESSSTEEL ROUND 3TRANSLUCENTWHITE 
STAINLESSSTEEL ROUND 4OPAQUEBLACK 
STAINLESSSTEEL ROUND 4TRANSLUCENTWHITE 
STAINLESSSTEEL ROUND OPAQUEBLACK 
STAINLESSSTEEL ROUND TRANSLUCENTWHITE 
STAINLESSSTEEL ROUND OPAQUEBLACK 
STAINLESSSTEEL ROUND TRANSLUCENTWHITE 
STAINLESSSTEEL ROUND 5OPAQUEBLACK 
STAINLESSSTEEL ROUND 5TRANSLUCENTWHITE 
4
RG
85 III
4 - 118 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RG 85 III - Short-travel system
Version Legending colour Order no.Form of lens Legending
stainless steel round Kopaque black 5.04.914.022/0100
stainless steel round Ktranslucent white 5.04.914.022/2000
stainless steel round Eopaque black 5.04.914.023/0100
stainless steel round Etranslucent white 5.04.914.023/2000
stainless steel round symbol „bell“opaque yellow 5.04.914.024/0400
stainless steel round symbol „open door“opaque black 5.04.914.025/0100
stainless steel round symbol „open door“translucent white 5.04.914.025/2000
stainless steel round symbol „close door“opaque black 5.04.914.026/0100
stainless steel round symbol „close door“translucent white 5.04.914.026/2000
stainless steel round symbol „ventilator“opaque black 5.04.914.027/0100
stainless steel round symbol „ventilator“translucent white 5.04.914.027/2000
stainless steel round symbol „arrow“opaque black 5.04.914.028/0100
stainless steel round symbol „arrow“translucent white 5.04.914.028/2000
The lenses without legending can not be engraved - other than the mentioned legends on request.
RG 85 III - Lenses for keyswitches, square
Version Legending colour Order no.Form of lens Legending
aluminum square -- 5.04.915.100/2000
aluminum square 1opaque black 5.04.915.101/0100
aluminum square 1translucent white 5.04.915.101/2000
aluminum square 2opaque black 5.04.915.102/0100
aluminum square 2translucent white 5.04.915.102/2000
aluminum square 3opaque black 5.04.915.103/0100
Technical data see page 4 - 114
4
RG
85 III
PCB Keyswitches Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
Version Legending colour Order no.Form of lens Legending
ALUMINUM SQUARE 3TRANSLUCENTWHITE 
ALUMINUM SQUARE 4OPAQUEBLACK 
ALUMINUM SQUARE 4TRANSLUCENTWHITE 
ALUMINUM SQUARE OPAQUEBLACK 
ALUMINUM SQUARE TRANSLUCENTWHITE 
ALUMINUM SQUARE OPAQUEBLACK 
ALUMINUM SQUARE TRANSLUCENTWHITE 
ALUMINUM SQUARE 5OPAQUEBLACK 
ALUMINUM SQUARE 5TRANSLUCENTWHITE 
ALUMINUM SQUARE KOPAQUEBLACK 
ALUMINUM SQUARE KTRANSLUCENTWHITE 
ALUMINUM SQUARE %OPAQUEBLACK 
ALUMINUM SQUARE %TRANSLUCENTWHITE 
ALUMINUM SQUARE SYMBOLuBELLhOPAQUEYELLOW 
ALUMINUM SQUARE SYMBOLuOPENDOORhOPAQUEBLACK 
ALUMINUM SQUARE SYMBOLuOPENDOORhTRANSLUCENTWHITE 
ALUMINUM SQUARE SYMBOLuCLOSEDOORhOPAQUEBLACK 
ALUMINUM SQUARE SYMBOLuCLOSEDOORhTRANSLUCENTWHITE 
ALUMINUM SQUARE SYMBOLuVENTILATORhOPAQUEBLACK 
ALUMINUM SQUARE SYMBOLuVENTILATORhTRANSLUCENTWHITE 
ALUMINUM SQUARE SYMBOLuARROWhOPAQUEBLACK 
ALUMINUM SQUARE SYMBOLuARROWhTRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE -- 
STAINLESSSTEEL SQUARE 1OPAQUEBLACK 
STAINLESSSTEEL SQUARE 1TRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE OPAQUEBLACK 
STAINLESSSTEEL SQUARE TRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE 3OPAQUEBLACK 
4
RG
85 III
 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
Version Legending colour Order no.Form of lens Legending
STAINLESSSTEEL SQUARE 3TRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE 4OPAQUEBLACK 
STAINLESSSTEEL SQUARE 4TRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE OPAQUEBLACK 
STAINLESSSTEEL SQUARE TRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE OPAQUEBLACK 
STAINLESSSTEEL SQUARE TRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE 5OPAQUEBLACK 
STAINLESSSTEEL SQUARE 5TRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE KOPAQUEBLACK 
STAINLESSSTEEL SQUARE KTRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE %OPAQUEBLACK 
STAINLESSSTEEL SQUARE %TRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE SYMBOLuBELLhOPAQUEYELLOW 
STAINLESSSTEEL SQUARE SYMBOLuOPENDOORhOPAQUEBLACK 
STAINLESSSTEEL SQUARE SYMBOLuOPENDOORhTRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE SYMBOLuCLOSEDOORhOPAQUEBLACK 
STAINLESSSTEEL SQUARE SYMBOLuCLOSEDOORhTRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE SYMBOLuVENTILATORhOPAQUEBLACK 
STAINLESSSTEEL SQUARE SYMBOLuVENTILATORhTRANSLUCENTWHITE 
STAINLESSSTEEL SQUARE SYMBOLuARROWhOPAQUEBLACK 
STAINLESSSTEEL SQUARE SYMBOLuARROWhTRANSLUCENTWHITE 
4HELENSESWITHOUTLEGENDINGCANNOTBEENGRAVEDOTHERTHANTHEMENTIONEDLEGENDSONREQUEST
4
RG
85 III
PCB Keyswitches Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Lenses for keylock switches, round
Version Legending colour Order no.Form of lens Legending
ALUMINUM ROUND -- 5.04.915.200/2000
STAINLESSSTEEL ROUND -- 
RG 85 III - Lenses for keylock switches, square
Version Legending colour Order no.Form of lens Legending
ALUMINUM SQUARE -- 
STAINLESSSTEEL SQUARE -- 
RG 85 III - Lens, round, for signal indicators
Version Legending colour Order no.Form of lens Legending
PLASTICTRANSLUCENT ROUND -- 
4
RG
85 III
 PCB Keyswitches
Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
RG 85 III - Lens, square, for signal indicators
Version Legending colour Order no.Form of lens Legending
PLASTICTRANSLUCENT SQUARE -- 
RG 85 III - Lens, triangular, for signal indicators
Version Legending colour Order no.Form of lens Legending
PLASTICTRANSLUCENT TRIANGULAR -- 5.04.903.011/0000
Cable, 8 wires, with socket connectors on both ends
Version Legending colour Order no.Form of lens Legending
LENGTHM - -- 
LENGTHM - -- 
4
RG
85 III
PCB Keyswitches Stock itemsAREMARKED
BYbold printed order numbers.
RG 85 III - Short-travel system
Fixing rail, length 490 mm
Version Legending colour Order no.Form of lens Legending
LENGTHMM - -- 
Spacer
Version Legending colour Order no.Form of lens Legending
MOUNTINGONRAILS - -- 
SINGLEMOUNTING - -- 
Fixing piece for mounting the elements with the rail fixing method
Version Legending colour Order no.Form of lens Legending
- - -- 
4
RS
76
4 - 125PCB Keyswitches
RS 76 - Full-travel keyswitches
General Data
The RS 76 full-travel keyswitches are designed for configuring keyboards. They offer very comfortable operation with an
overall height of 15.5 / 15.9 mm and a key travel of 4 mm. The modular system with a grid of 3/4“ = 19.05 mm enables
you to design any key block you may want.
Mechanical contact system RS 76 M
A gold alloy is used as the contact material and provides high contact reliability, low contact resistance and short boun-
cing time.
Solid-state contact system RS 76 C
The solid-state switch in Hall-IC technology ensures bounce-free and wear-free switching and a long operating life.
Function: When pressing the keys, a permanent magnet changes its position relative to the Hall-IC and thereby genera-
tes an output signal. Their use is especially recommended in hostile environments and for heavy duty applications.
Content
RS 76 M - Full-travel keyswitch, not illuminable 4 - 132
RS 76 M - Full-travel keyswitch, not illuminable 4 - 133
RS 76 M - Full-travel keyswitch, with diode, not illuminable 4 - 133
RS 76 M - Full-travel keyswitch, illuminable 4 - 134
RS 76 M - Full-travel keyswitch, illuminable, momentary 4 - 135
RS 76 M - Full-travel keyswitch, illuminable, latching 4 - 135
RS 76 MX - Full-travel keyswitch, fully illuminable 4 - 136
RS 76 C - Full-travel keyswitch, not illuminable 4 - 138
RS 76 C - Full-travel keyswitch, not illuminable 4 - 139
RS 76 C - Full-travel keyswitch, illuminable 4 - 140
RS 76 C - Full-travel keyswitch, illuminable, momentary 4 - 141
RS 76 C - Full-travel keyswitch, illuminable, latching 4 - 141
RS 76 - Keycaps, not illuminable 4 - 142
RS 76 - Keycap, opaque 4 - 142
RS 76 - Keycap, opaque, with nail protection 4 - 142
RS 76 - Keycap with legend insert 4 - 143
RS 76 - Keycaps, illuminable 4 - 144
RS 76 - Keycap with light bar 4 - 144
RS 76 - Keycap, illuminable, with legend insert 4 - 144
RS 76 - Keycap, illuminable, with nail protection and legend insert 4 - 145
RS 76 - Keycap, illuminable, with legend insert 4 - 145
RS 76 MX - Keycap, fully illuminable 4 - 146
RS 76 - Keycaps, with legend, two-shot moulded/keycap sets 4 - 148
RS 76 - Keycap set, symbols A-Z 4 - 148
RS 76 - Keycap set, symbols 0-9 4 - 149
RS 76 - Accessories 4 - 150
RS 76 - Cover IP40 4 - 151
4 - 126 PCB Keyswitches
4
RS
76
RS 76 - Full-travel keyswitches
The RAFI full-travel keyswitches RS 76 are modular
systems for designing individual key blocks and
keyboards in the 3/4 inch (= 19.05 mm) grid.
Definitions
Momentary keyswitches
Momentary keyswitches return to their initial position
after being pressed (momentary action).
Latching keyswitches
Latching keyswitches lock when actuated and are
returned to their initial position when pressed again
(push-push action).
Keycap materials
Keycap without legend insert: ABS
Keycap with legend insert:
– Keycap body: ABS
– Lens: PC
Keycap, n-module
A 2-module keycap f. ex. has the twofold length of a
1-module keycap.
Contact principle
There are two contact principles:
– Mechanical (M): Cross contact (RS 76 M)
Bridge contact
(RS 76 M, illuminated)
– Contactless (C): Based on Hall-IC (RS 76 C)
Manual Soldering
The soldering temperature should not exceed 300 °C
and the soldering time should be less than 5 seconds.
Keycaps can be legended by different methods:
Two-shot moulding
Using this method the symbol is separately manufactured
from a plastic and then the appropriate keycap form is
moulded round it. Advantage: The character becomes a
integrated part of the keycap, thus eliminating abrasion.
All RAFI keycap sets with standard legending are manu-
fatured by this method.
Customer specific two-shot moulded keycaps on request.
Printing
Keycaps can be printed with a two-component ink on
request. The abrasin of this kind of legending is high.
This method of legending is suitable for average
volumes.
Engraving
In this labour intensive process the keycaps are engraved
with the required symbol, then inlaid with ink. Only used
for small volumes.
Laser-printing
This method of legending can be recommended when
complete keyboards are required in different keyboard
layouts for which RAFI will develop the respective soft-
ware. The keyboards can then be legended within a short
time. This method of legending ist particularly recom-
mended for average to large volumes.
Legend inserts
In the case of keycaps with replaceable legend inserts it is
possible to print or engrave the legend inserts. As these
insets are protected by the lens, there can be no abrasion
here either.
Legending of keycaps
PCB Keyswitches 4 - 127
4
RS
76
RS 76 - Full-travel keyswitches
No. Description
1.1 Keyswitch RS 76 C
1.2 Keyswitch RS 76 C with LED
1.3 Keyswitch RS 76 M
1.4 Keyswitch R 76 M with LED
2 Keycap, 1- resp. multi-module
3 Keycap with nail protection, 1- resp. multi-module
5 Keycap, illuminated
6 Keycap, illuminated
7 Keycap, illuminated
9.1 LED
9.2 Spacer for LED (for RS 76 C only)
10.1 Plunger for mult-moduel keycaps*
10.2 Sleeve for multi-moduel keycaps*
10.3 Metal lever for multi-module keycaps*
10.4 Bearing bracket for multi-module keycaps*
11 Covers
* These parts are included as a complete packet in the delivery of keycaps
2-module.
Design
4 - 128 PCB Keyswitches
4
RS 76 - Full-travel keyswitches
For 1 – 13
/4-module keycaps (view on component side)
For 2-, 3- and 8-module keycaps (view on component side)
The hole patterns apply to the horizontal position of
the keycaps only. Should they be in a vertical position,
the momentary keyswitch must be mounted accordingly,
i. e. rotated by 90°.
RS 76 M
Momentary keyswitch, non-illuminated Momentary keyswitch, illuminated
RS 76 C
RS 76 M/C
Keycap
2-module
L 1
mm
25,40
3-module 30,48
5-module 68,58
L 2
mm
22,86
24,13
68,58
Important note: In the case of 2-, 3- and 8-module key-
caps, additional holes must be provided for the accesso-
ries.
In the case of keycaps < 2-module, neither accessories nor
holes are required.
Metal bow touches the surface of PCB,
in this area no conductor tracks on component side
sHOLESFORBEARINGBRACKETDIAM
No through-plating
Hole diam. 2
Nor through-plating
Hole Pattern PCB RS 76 M/RS 76 C
RS
76
PCB Keyswitches 4 - 129
4
RS 76 - Full-travel keyswitches
Turn-on delay time tPHL 3 μs
Tw = 25 °C
7 μs 10 μs
Turn-off delay time tPHL 4 μs 5 μs 6 μs
Fall/rise time tPHL 2 μs 2,5 μs 3 μs
tPHL 1 μs 1,5 μs 2,5 μs
Tw = 50 °C Tw = 70 °COutput pulse diagram
Dynamic characteristics (max.)
Static with Enable Input
Block diagram
Hall IC
Specific Technical Data RS 76 C
RS
76
4 - 130 PCB Keyswitches
4
RS 76 - Full-travel keyswitches
Driving of logic components
Driving of a PNP transistor
Use in keyboards
Use as static key with open collector output.
Output transistor (NPN) is conductive when actuated.
Indication of logical states
Examples for Application RS 76 C
RS
76
4
RS
76
4 - 132 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 M - Full-travel keyswitch, not illuminable
Technical Data
General information
Recommended key grid 19.05 mm
Mechanical design
Contact function momentary
Mounting soldering
Terminals solder terminals,
tin-plated
Contact system cross contact
Contact arrangement 1 NO
Contact materials Au alloy
Illumination no
Mechanical characteristics
Operating force max. see order block
Operating travel 4 mm
Switching travel 1.5 - 2.8 mm
Robustness min. 100 N
Electrical characteristics
Rated voltage min. 2 V (with Diode 3 V)
Rated voltage max. 35 V
Rated current min. 0.01 mA
Rated current max. 100 mA
Rated power max. 1 W
Contact resistance when new 100 mE
max. (without diode)
Contact resistance acc. to 3 E
life max. (without diode)
Insulation resistance 109 E
ESD strength max. 8 kV
Bouncing time max. 5 ms
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Storage temperature min. -40 °C
Storage temperature max. +80 °C
(product)
Storage temperature max. +50 °C
(rail)
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. 107
(operations)
Degree of protection IP40
Flammability of materials UL 94 HB
Description Photo Order no. Additional acces-
sories see page
Typical accessories RS 76 M - Full-travel keyswitch, not illuminable
RS 76 C - Keycap with legend insert 5.04.665.221/5520 4 - 143
RS 76 C - Keycap, opaque, with nail protection 5.80.000.000/0152 4 - 142
RS 76 C - Keycap, opaque 5.82.000.000/0152 4 - 142
4
RS
76
4 - 133PCB Keyswitches Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 M - Full-travel keyswitch, not illuminable
Contact function Bestell-Nr.Illumination Contact
arrangement
Contact materials Operating travel Operating force
max.
momentary no 1 NO Au alloy 4 mm 0.9 N 3.13.002.502/0000
momentary no 1 NO Au alloy 4 mm 1.4 N 3.13.002.512/0000
Technical data see page 4 - 132
For accessories, refer to RS 76 special accessories.
For keycaps, see keycaps for RS 76.
RS 76 M - Full-travel keyswitch, with diode, not illuminable
Contact function Bestell-Nr.Illumination Contact
arrangement
Contact materials Operating travel Operating force
max.
momentary no 1 NO Au alloy 4 mm 0.9 N 3.13.005.001/0000
momentary no 1 NO Au alloy 4 mm 1.4 N 3.13.005.011/0000
Technical data see page 4 - 132
For accessories, refer to RS 76 special accessories.
For keycaps, see keycaps for RS 76.
4
RS
76
4 - 134 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 M - Full-travel keyswitch, illuminable
RS 76MX, keyboard fully illuminatedRS 76MX, for full illuminationPict.: RS 76M, for spot illumination
Technical Data
General information
Recommended key grid 19.05 mm
Mechanical design
Contact function see order block
Mounting soldering
Terminals solder terminals,
tin-plated
Contact system bridge contact
Contact arrangement 1 NO
Contact materials Au alloy
Illumination see order block
Mechanical characteristics
Operating force max. 1 N
Operating travel 4 mm
Switching travel 1.5 - 2.8 mm
Robustness min. 100 N
Electrical characteristics
Rated voltage min. 2 V
Rated voltage max. 35 V
Rated current min. 0.01 mA
Rated current max. 100 mA
Rated power max. 1 W
Contact resistance when new 200 mE
max.
Contact resistance acc. to 3 E
life max.
Insulation resistance 109 E
ESD strength max. 8 kV
Bouncing time max. 10 ms
Other specifications
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Storage temperature min. -40 °C
Storage temperature max. +80 °C
(product)
Storage temperature max. +50 °C
(rail)
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. 107 momentary, 105
(operations) latching
Degree of protection IP40
Flammability of materials UL 94 HB
Description Photo Order no. Additional acces-
sories see page
Typical accessories RS 76 M - Full-travel keyswitch, illuminable
RS 76 - Cover IP40, 1-module, charcoal grey 5.04.520.174/0152 4 - 151
RS 76 C - Keycap, illuminated, with legend insert 5.04.665.521/5520 4 - 144
RS 76 C - Keycap, illuminated, with nail protection and
legend insert 5.04.665.911/5520 4 - 145
RS 76 C - Keycap with light bar 5.82.110.000/0242 4 - 144
4
RS
76
4 - 135PCB Keyswitches Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 M - Full-travel keyswitch, illuminable, momentary
Pict.: RS 76M, for spot illumination
Contact function Order no.Contact system Illumination Recommended key grid
momentary bridge contact spot illumination
possible with 3 LED
19.05 mm 3.13.002.102/0000
Technical data see page 4 - 134
For accessories, refer to RS 76 special accessories.
For keycaps, see keycaps for RS 76.
RS 76 M - Full-travel keyswitch, illuminable, latching
Contact function Order no.Contact system Illumination Recommended key grid
latching bridge contact spot illumination
possible with 3 LED
19.05 mm 3.13.002.022/0000
Technical data see page 4 - 134
For accessories, refer to RS 76 special accessories.
For keycaps, see keycaps for RS 76.
4
RS
76
4 - 136 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 MX - Full-travel keyswitch, fully illuminable
Pict.: RS 76MX, for full illumination
Contact function Order no.Contact system Illumination Recommended key grid
momentary bridge contact 2 SMT LED needed 19.05 mm 3.13.002.922/0000
Technical data see page 4 - 134
Accessoires:
RS 76 MX - Keycap, fully illuminated: 5.05.511.168/0209
RS 76 MX - Keycap, fully illuminated: 5.05.511.168/0754
For accessories, refer to RS 76 special accessories.
For keycaps, see keycaps for RS 76.
The SMT LEDs are soldered on the back of the printed circuit board and shine through openings in the board and keyswitch housing.
4
RS
76
4 - 138 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 C - Full-travel keyswitch, not illuminable
Technical Data
General information
Recommended key grid 19.05 mm
Mechanical design
Contact function momentary
Mounting soldering
Terminals solder terminals,
tin-plated
Contact system contactless with
Hall-IC
Illumination no
Mechanical characteristics
Switching travel off 0.8 ... 2.4 mm
Operating force max. see order block
Operating travel 4 mm
Switching travel on 1.5 - 2.8 mm
Robustness min. 100 N
Electrical characteristics
Operating voltage DC 4.75 ... 5.25 V
Supply current max. at UIL = 0 V 0.5 mA
Supply current max. at UIH = 5 V 5 mA
Input voltage (F) at UIL = 0 V 0.4 V
Input voltage (F) at UIH = 2.4V 5.25 V
Output load current (Q) max. 16 mA
Output residual current (Q) max. 10 μA
Output saturation voltage 0.4 V
(Q) max. bei 16 mA
ESD strength max. 8 kV
Output switching times (Q) 3 μs
at 25 °C, tPHL
Output switching times (Q) 4 μs
at 25 °C, tPLH
Output switching times (Q) 1 μs
at 25 °C, tTHL
Output switching times (Q) 2 μs
at 25 °C, tTLH
Other specifications
Reliability of Hall-IC at 25 °C λ = 2.5 x 10-7 h-1
Ambient temp. operating min. 0 °C
Ambient temp. operating max. +70 °C
Storage temperature min. -40 °C
Storage temperature max. +80 °C
(product)
Storage temperature max. (rail) +50 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. see order block
(operations)
Degree of protection IP40
Flammability of materials UL 94 HB
Description Photo Order no. Additional acces-
sories see page
Typical accessories RS 76 C - Full-travel keyswitch, not illuminable
RS 76 C - Keycap with legend insert 5.04.665.221/5520 4 - 143
RS 76 C - Keycap, opaque, with nail protection 5.80.000.000/0152 4 - 142
RS 76 C - Keycap, opaque 5.82.000.000/0152 4 - 142
4
RS
76
4 - 139PCB Keyswitches Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 C - Full-travel keyswitch, not illuminable
Contact function Operating life min.
(operations)
Illumination Operating force max. Operating travel Order no.
momentary 108 no 0.7 N 4 mm 3.13.001.010/0000
momentary 108 no 1 N 4 mm 3.13.001.210/0000
Technical data see page 4 - 138
For accessories and keycaps, refer to RS 76. For applications, refer to the general description of RS 76.
4
RS
76
4 - 140 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 C - Full-travel keyswitch, illuminable
Technical Data
General information
Recommended key grid 19.05 mm
Mechanical design
Contact function see order block
Mounting soldering
Terminals solder terminals,
tin-plated
Contact system contactless with
Hall-IC
Illumination with LED
LED colour see order block
Mechanical characteristics
Switching travel on 1.5 - 2.8 mm
Switching travel off 0.8 ... 2.4 mm
Operating force max. 0.7 N
Operating travel 4 mm
Robustness min. 100 N
Electrical characteristics
Number of LED see order block
Operating voltage DC 4.75 ... 5.25 V
Supply current max. at UIL = 0 V 0.5 mA
Supply current max. at UIH = 5 V 5 mA
Input voltage (F) at UIL = 0 V 0.4 V
Input voltage (F) at UIH = 2.4V 5.25 V
Output load current (Q) max. 16 mA
Output residual current (Q) max. 10 μA
Output saturation voltage 0.4 V
(Q) max. bei 16 mA
ESD strength max. 8 kV
Output switching times (Q) 3 μs
at 25 °C, tPHL
Output switching times (Q) 4 μs
at 25 °C, tPLH
Output switching times (Q) 1 μs
at 25 °C, tTHL
Output switching times (Q) 2 μs
at 25 °C, tTLH
Other specifications
Reliability of Hall-IC at 25 °C λ = 2.5 x 10 -7 h-1
Ambient temp. operating min. 0 °C
Ambient temp. operating max. +70 °C
Storage temperature min. -40 °C
Storage temperature max. +80 °C
(product)
Storage temperature max. +50 °C
(rail)
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Operating life min. see order block
(operations)
Degree of protection IP40
Flammability of materials UL 94 HB
Description Photo Order no. Additional acces-
sories see page
Typical accessories RS 76 C - Full-travel keyswitch, illuminable
RS 76 - Cover IP40, 1-module, light grey 5.04.520.174/0242 4 - 151
RS 76 C - Keycap, illuminated, with legend insert 5.04.665.521/5520 4 - 144
RS 76 C - Keycap, illuminated, with nail protection
and legend insert
5.04.665.911/5520 4 - 145
4
RS
76
4 - 141PCB Keyswitches Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
Description Photo Order no. Additional acces-
sories see page
Typical accessories RS 76 C - Full-travel keyswitch, illuminable
RS 76 C - Keycap with light bar 5.82.110.000/0242 4 - 144
RS 76 C - Full-travel keyswitch, illuminable, momentary
Contact function Operating life min.
(operations)
Illumination Operating force max. Operating travel Order no.
momentary 108 with LED 0.7 N 4 mm 3.13.001.110/0000
Technical data see page 4 - 140
RS 76 C - Full-travel keyswitch, illuminable, latching
Contact function Operating life min.
(operations)
Illumination Operating force max. Operating travel Order no.
latching 105 with LED 0.7 N 4 mm 3.13.001.130/0000
Technical data see page 4 - 140
4
RS
76
4 - 142 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 - Keycaps, not illuminable
transparent colourlessopaque with nail protection charcoal grey / whitePict.: light beige
RS 76 - Keycap, opaque
Pict.: dark grey light beige
Size of keycap Order no.Illumination Colour of keycap /
legending
Colour of lens /
legend insert
1-module no charcoal grey/- -5.82.000.000/0152
1-module no light grey/- -5.82.000.000/0242
Keycap sets available in two-shot moulded design.
Other keycap sizes, e.g. 1.25-, 1.5-, 1.75-, 2-, 3-, 5- and 8-module versions available on request.
RS 76 - Keycap, opaque, with nail protection
Pict.: light beige opaque with nail protection charcoal grey / white
Size of keycap Order no.Illumination Colour of keycap /
legending
Colour of lens /
legend insert
1-module no charcoal grey/- -5.80.000.000/0152
1-module no light grey/- -5.80.000.000/0242
Keycap sets available in two-shot moulded design.
Other keycap sizes, e.g. 1.25-, 1.5-, 1.75-, 2-, 3- and 8-module versions available on request.
4
RS
76
4 - 143PCB Keyswitches Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 - Keycap with legend insert
Pict.: transparent colourless
Size of keycap Order no.Illumination Colour of keycap /
legending
Colour of lens /
legend insert
1-module no charcoal grey/- colourless/white 5.04.665.221/5520
1-module no light grey/- colourless/white 5.04.665.230/5520
Supplied as single parts: Mat lens, legend insert, keycap body.
Other colours on request.
4
RS
76
4 - 144 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 - Keycaps, illuminable
light beige
RS 76 - Keycap with light bar
Pict.: light beige
Size of keycap Order no.Illumination Colour of keycap /
legending
Colour of lens /
legend insert
1-module yes light grey/- -5.82.110.000/0242
1-module yes charcoal grey/- -5.82.110.000/0152
Other colours on request.
RS 76 - Keycap, illuminable, with legend insert
Size of keycap Order no.Illumination Colour of keycap /
legending
Colour of lens /
legend insert
1-module yes charcoal grey/- colourless/white 5.04.665.521/5520
1-module yes light grey/- colourless/white 5.04.665.530/5520
Supplied as single parts: Mat lens, legend insert, diffuser foil, keycap body.
Other colours on request.
4
RS
76
4 - 145PCB Keyswitches Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 - Keycap, illuminable, with nail protection and legend insert
Pict.: light grey, yellow lens
Size of keycap Order no.Illumination Colour of keycap /
legending
Colour of lens /
legend insert
1-module yes charcoal grey/- colourless/white 5.04.665.911/5520
1-module yes light grey/- colourless/white 5.04.665.920/5520
Supplied as single parts: Mat lens, legend insert, keycap body.
Other colours on request.
RS 76 - Keycap, illuminable, with legend insert
Pict.: red
Size of keycap Order no.Illumination Colour of keycap /
legending
Colour of lens /
legend insert
1-module yes charcoal grey/- colourless/white 5.04.665.161/5520
1-module yes light grey/- colourless/white 5.04.665.170/5520
Supplied as single parts: Mat lens, legend insert, diffuser foil, keycap body.
Other colours on request.
4
RS
76
4 - 146 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 MX - Keycap, fully illuminable
RS 76MX, keyboard fully illuminated
Size of keycap Order no.Illumination Colour of keycap /
legending
Colour of lens /
legend insert
1-module yes white/- white translucent/- 5.05.511.168/0209
1-module yes light grey/- white translucent/- 5.05.511.168/0754
1¼-module yes white/- white translucent/- 5.05.511.169/0209
1½-module yes white/- white translucent/- 5.05.511.170/0209
1¾-module yes white/- white translucent/- 5.05.511.171/0209
1¼-module with light
conductor
yes white/- white translucent/- 5.05.511.173/0209
Laser-printed versions available on request.
4
RS
76
4 - 148 PCB Keyswitches
Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 - Keycaps, with legend, two-shot moulded/keycap sets
opaque light beige / brownPict.: opaque light beige / brown
RS 76 - Keycap set, symbols A-Z
Pict.: opaque light beige / brown light beige
Size of keycap Order no.Form of lens Colour of keycap /
legending
Symbol
1-module keycap opaque
with nail protection
charcoal grey/white A-Z 5.00.999.500/0000
1-module keycap opaque
with nail protection
light grey/black A-Z 5.00.999.824/0000
1-module keycap opaque charcoal grey/white A-Z 5.00.999.525/0000
1-module keycap opaque light grey/black A-Z 5.00.999.825/0000
Other symbols and colours on request.
4
RS
76
4 - 149PCB Keyswitches Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 - Keycap set, symbols 0-9
Pict.: opaque light beige / brown opaque with nail protection charcoal grey / white
Size of keycap Order no.Form of lens Colour of keycap /
legending
Symbol
1-module keycap opaque
with nail protection
charcoal grey/white 0-9 5.00.999.504/0000
1-module keycap opaque
with nail protection
light grey/black 0-9 5.00.999.826/0000
1-module keycap opaque charcoal grey/white 0-9 5.00.999.529/0000
1-module keycap opaque light grey/black 0-9 5.00.999.827/0000
Other symbols and colours on request.
4
RS
76
4 - 150 PCB Keyswitches
RS 76 - Full-travel keyswitches
RS 76 - Accessories
dark greyPict.: light beige
4
RS
76
4 - 151PCB Keyswitches Stock items are marked
by bold printed order numbers.
RS 76 - Full-travel keyswitches
RS 76 - Cover IP40
Pict.: light beige
Order no.Short text Feature 1 Feature 2
RS 76 - Cover IP40, 1/4-module, charcoal grey charcoal grey ¼-module 5.04.520.171/0152
RS 76 - Cover IP40, 1/4-module, light grey light grey ¼-module 5.04.520.171/0242
RS 76 - Cover IP40, 1/4-module, light beige light beige ¼-module 5.04.520.171/0710
RS 76 - Cover IP40, 1/4-module, dark grey dark grey ¼-module 5.04.520.171/0801
RS 76 - Cover IP40, 1/2-module, charcoal grey charcoal grey ½-module 5.04.520.172/0152
RS 76 - Cover IP40, 1/2-module, light grey light grey ½-module 5.04.520.172/0242
RS 76 - Cover IP40, 1/2-module, light beige light beige ½-module 5.04.520.172/0710
RS 76 - Cover IP40, 1/2-module, dark grey dark grey ½-module 5.04.520.172/0801
RS 76 - Cover IP40, 3/4-module, charcoal grey charcoal grey ¾-module 5.04.520.173/0152
RS 76 - Cover IP40, 3/4-module, light grey light grey ¾-module 5.04.520.173/0242
RS 76 - Cover IP40, 3/4-module, light beige light beige ¾-module 5.04.520.173/0710
RS 76 - Cover IP40, 3/4-module, dark grey dark grey ¾-module 5.04.520.173/0801
RS 76 - Cover IP40, 1-module, charcoal grey charcoal grey 1-module 5.04.520.174/0152
RS 76 - Cover IP40, 1-module, light grey light grey 1-module 5.04.520.174/0242
RS 76 - Cover IP40, 1-module, light beige light beige 1-module 5.04.520.174/0710
RS 76 - Cover IP40, 1-module, dark grey dark grey 1-module 5.04.520.174/0801
Other colours on request.
4
4 - 153PCB Keyswitches Key
Swit-
ches
Keylock and rotary switches for PCB
General Data
Keylock switches for PCB mounting. Matching with the RS 76 full-travel keyswitches and the RF 15 and RF 19
short-travel keyswitches.
Content
MICROMEC - Keylock switch IP54 4 - 154
MICROMEC - Keylock switch IP54 4 - 156
EUROLOCKS - Keylock switch IP54 4 - 158
EUROLOCKS - Keylock switch IP54 4 - 159
Priority keylock switch IP54 4 - 160
Priority keylock switch IP54 4 - 161
Rotary switch IP40 4 - 162
Rotary switch IP40 4 - 163
4
4 - 154 PCB Keyswitches
Key
Swit-
ches
Stock items are marked
by bold printed order numbers.
Keylock and rotary switches for PCB
MICROMEC - Keylock switch IP54
PCB hole pattern, component sidePict.: light grey
Technical Data
General information
Colour see order block
Form of collar square
Dimensions
Length of collar 19 mm
Width of collar 19 mm
Overall height 19.5 mm
Mechanical design
Mounting soldering
Terminals tin-plated
Contact system cross contact self
cleaning
Contact function see order block
Contact materials Au alloy
Illuminability no
Lock Micromec
Wafers 5
Lock type 001
Number of locking positions 500
Main key on request
Symmetric key no
Group key on request
Key removal position see order block
General key on request
Mechanical characteristics
Switching torque 0.04 ... 0.10 Nm
Robustness max. 2 Nm
Dielectric strength AC min. 500 V
Rated power max. 1 W
Electrical characteristics
Rated voltage 2 ... 35 V
Rated current max. 100 mA
Contact resistance when new 100 mE
max.
Contact resistance acc. to 200 mE
life max.
Insulation resistance 109 E
ESD strength max. 8 kV
Other specifications
Rotating angle see order block
Operating life 10,000
Degree of protection from IP54
front side
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Storage temperature min. -40 °C
Storage temperature max. +80 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Flammability of materials UL 94 HB
Description Photo Order no. Additional acces-
sories see page
Typical accessories MICROMEC - Keylock switch IP54
O-ring for keylock switch 5.30.120.015/0100 5 - 25
Spare key, for single action, e.g. 1 x 90°
(delivery content 1 key)
5.58.007.001/0000
Spare key, for double action, e.g. 2 x 90°
(delivery content 1 key)
5.58.008.001/0000
Spare key for 3 angles, f.ex. 3 x 90° degree (content 1 key) 5.58.009.001/0100
4
4 - 155PCB Keyswitches Key
Swit-
ches
Stock items are marked
by bold printed order numbers.
Keylock and rotary switches for PCB
Description Photo Order no. Additional acces-
sories see page
Typical accessories MICROMEC - Keylock switch IP54
Spare key for 4 angles, f.ex. 4 x 90 degrees,
(content 1 key)
5.58.010.001/0100
Switching
position
0
Contact function
1
2
3
Hole patterns PCB
View on component side
Configuration Diagram/Dimensional Drawing
4
4 - 156 PCB Keyswitches
Key
Swit-
ches
Stock items are marked
by bold printed order numbers.
Keylock and rotary switches for PCB
MICROMEC - Keylock switch IP54
Pict.: charcoal grey PCB hole pattern, component side
Contact function Order no.Colour Rotating angle Key removal
position
momentary charcoal grey 01 x 40° 3.13.026.041/0000
momentary light grey 01 x 40° 3.13.026.541/0000
latching charcoal grey 01 x 90° 3.13.026.001/0000
latching light grey 01 x 90° 3.13.026.501/0000
latching charcoal grey 0+11 x 90° 3.13.026.006/0000
latching light grey 0+11 x 90° 3.13.026.506/0000
latching charcoal grey 02 x 90° 3.13.026.011/0000
latching light grey 02 x 90° 3.13.026.511/0000
latching charcoal grey 0+1+22 x 90° 3.13.026.016/0000
latching light grey 0+1+22 x 90° 3.13.026.516/0000
latching charcoal grey 02 x 90° 3.13.026.601/0000
latching light grey 02 x 90° 3.13.026.851/0000
latching charcoal grey 0+1+32 x 90° 3.13.026.606/0000
latching light grey 0+1+32 x 90° 3.13.026.856/0000
latching charcoal grey 03 x 90° 3.13.026.021/0000
latching light grey 03 x 90° 3.13.026.521/0000
latching charcoal grey 0+1+2+33 x 90° 3.13.026.026/0000
latching light grey 0+1+2+33 x 90° 3.13.026.526/0000
latching charcoal grey 04 x 90° without stop 3.13.026.031/0000
latching light grey 04 x 90° without stop 3.13.026.531/0000
latching charcoal grey 0+1+2+34 x 90° without stop 3.13.026.036/0000
latching light grey 0+1+2+34 x 90° without stop 3.13.026.536/0000
Technical data see page 4 - 154
2 keys included.
Other lock variants available on request.
4
4 - 158 PCB Keyswitches
Key
Swit-
ches
Stock items are marked
by bold printed order numbers.
Keylock and rotary switches for PCB
EUROLOCKS - Keylock switch IP54
PCB hole pattern, component sidePict.: light grey
Technical Data
General information
Colour see order block
Form of collar square
Dimensions
Length of collar 19 mm
Width of collar 19 mm
Overall height 19.5 mm
Mechanical design
Mounting soldering
Terminals tin-plated
Contact system cross contact self
cleaning
Contact function latching
Contact materials Au alloy
Illuminability no
Lock Eurolocks
Wafers 5
Lock type 801
Number of locking positions 50
Main key no
Symmetric key yes
Group key no
Key removal position see order block
General key no
Mechanical characteristics
Switching torque 0.04 ... 0.10 Nm
Robustness max. 2 Nm
Dielectric strength AC min. 500 V
Rated power max. 1 W
Electrical characteristics
Rated voltage 2 ... 35 V
Rated current max. 100 mA
Contact resistance when new 100 mE
max.
Contact resistance acc. to 200 mE
life max.
Insulation resistance 109 E
ESD strength max. 8 kV
Other specifications
Rotating angle see order block
Operating life 10,000
Degree of protection from IP54
front side
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Storage temperature min. -40 °C
Storage temperature max. +80 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Flammability of materials UL 94 HB
Description Photo Order no. Additional acces-
sories see page
Typical accessories EUROLOCKS - Keylock switch IP54
O-ring for keylock switch 5.30.120.015/0100 5 - 25
Spare key (delivery content 1 key) 5.58.006.801/0000
4
4 - 159PCB Keyswitches Key
Swit-
ches
Stock items are marked
by bold printed order numbers.
Keylock and rotary switches for PCB
EUROLOCKS - Keylock switch IP54
Pict.: light grey PCB hole pattern, component side
Contact function Order no.Colour Rotating angle Key removal
position
latching charcoal grey 01 x 90° 3.13.009.001/0000
latching light grey 01 x 90° 3.13.009.006/0000
latching charcoal grey 0+11 x 90° 3.13.009.031/0000
latching light grey 0+11 x 90° 3.13.009.036/0000
Technical data see page 4 - 158
2 keys included.
Other lock variants available on request.
For the switching arrangement, refer to Micromec keylock switch IP54.
4
4 - 160 PCB Keyswitches
Key
Swit-
ches
Keylock and rotary switches for PCB
Priority keylock switch IP54
PCB hole pattern, component sidePict.: light grey
General Data
Either 2 or 3 different keys are required, depending on the angle between positions. Key 1 can switch to position 1, key
2 can switch to position 1 and 2, etc.
Technical Data
General information
Colour see order block
Form of collar square
Dimensions
Length of collar 19 mm
Width of collar 19 mm
Overall height 19.5 mm
Mechanical design
Mounting soldering
Terminals tin-plated
Contact system cross contact self
cleaning
Contact function see order block
Contact materials Au alloy
Illuminability no
Lock Micromec
Wafers 5
Lock type 001
Number of locking positions 500
Main key yes
Symmetric key no
Group key yes
Key removal position see order block
General key yes
Mechanical characteristics
Switching torque 0.04 ... 0.10 Nm
Robustness max. 2 Nm
Dielectric strength AC min. 500 V
Rated power max. 1 W
Electrical characteristics
Rated voltage 2 ... 35 V
Rated current max. 100 mA
Contact resistance when new 100 mE
max.
Contact resistance acc. to 200 mE
life max.
Insulation resistance 109 E
ESD strength max. 8 kV
Other specifications
Rotating angle see order block
Operating life 10,000
Degree of protection from IP54
front side
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Storage temperature min. -40 °C
Storage temperature max. +80 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Flammability of materials UL 94 HB
O-ring for keylock switch 5.30.120.015/0100 5 - 25
Description Photo Order no. Additional acces-
sories see page
Typical accessories Priority keylock switch IP54
Stock items are marked
by bold printed order numbers.
4
4 - 161PCB Keyswitches Key
Swit-
ches
Stock items are marked
by bold printed order numbers.
Description Photo Order no. Additional acces-
sories see page
Typical accessories Priority keylock switch IP54
Set of keys for 2 x 90° type (2 keys) 5.58.099.012/0000
Set of keys for 3 x 90° type (3 keys) 5.58.099.013/0000
Priority keylock switch IP54
Pict.: charcoal grey PCB hole pattern, component side
Contact function Order no.Colour Rotating angle Key removal
position
latching charcoal grey 02 x 90° 3.13.027.001/0000
latching light grey 02 x 90° 3.13.027.501/0000
latching charcoal grey 0+1+22 x 90° 3.13.027.006/0000
latching light grey 0+1+22 x 90° 3.13.027.506/0000
latching charcoal grey 03 x 90° 3.13.027.011/0000
latching light grey 03 x 90° 3.13.027.511/0000
latching charcoal grey 0+1+2+33 x 90° 3.13.027.016/0000
latching light grey 0+1+2+33 x 90° 3.13.027.516/0000
Technical data see page 4 - 160
2 sets of keys included.
Other lock variants available on request.
For the switching arrangement, see IP54 Micromec keylock switch.
Either 2 or 3 different keys are required, depending on the angle between positions. Key 1 can switch to position 1, key 2 can switch to
position 1 and 2, etc.
Keylock and rotary switches for PCB
4
4 - 162 PCB Keyswitches
Key
Swit-
ches
Keylock and rotary switches for PCB
Rotary switch IP40
PCB hole pattern, component sidePict.: charcoal grey
Technical Data
General information
Colour see order block
Form of collar square
Dimensions
Length of collar 19 mm
Width of collar 19 mm
Overall height 24 mm
Mechanical design
Mounting soldering
Terminals tin-plated
Contact system cross contact self
cleaning
Contact function see order block
Contact materials Au alloy
Illuminability no
Mechanical characteristics
Torque against stop min. 0.45 Nm
Dielectric strength AC min. see order block
Rated power max. 1 W
Electrical characteristics
Rated voltage max. 35 V
Rated current max. 100 mA
Contact resistance when new 100 mE
max.
Contact resistance acc. to 200 mE
life max.
Insulation resistance 109 E
ESD strength max. 8 kV
Other specifications
Rotating angle see order block
Operating life 50,000
Degree of protection from IP40
front side
Ambient temp. operating min. -25 °C
Ambient temp. operating max. +70 °C
Storage temperature min. -40 °C
Storage temperature max. +80 °C
Environmental restistance acc. to IEC 60068-2
-14, -30, -33 and -78
Flammability of materials UL 94 HB
4
4 - 163PCB Keyswitches Key
Swit-
ches
Stock items are marked
by bold printed order numbers.
Keylock and rotary switches for PCB
Rotary switch IP40
Pict.: charcoal grey PCB hole pattern, component side
Contact function Colour Rotating angle Order no.
latching charcoal grey 1 x 90° 3.13.007.001/0152
latching charcoal grey 2 x 90° 3.13.007.011/0152
latching charcoal grey 3 x 90° 3.13.007.021/0152
latching charcoal grey 4 x 90° 3.13.007.031/0152
Technical data see page 4 - 162
Other colour variants available on request