5962-0623601, 5962-0623602 Data Sheet November 3, 2011 670MHz Low Noise Amplifiers Features The 5962-0623601QPC and 5962-0623602QPC are fully DLA SMD compliant parts and the SMD data sheets are available on the DLA website (http://www.landandmaritime.dla.mil/Programs/MilSpec/Doc Search.aspx). The 5962-0623601QPC is electrically equivalent to the EL5132 and the 5962-0623602QPC is electrically equivalent to the EL5133, reference these data sheets for additional information. These amplifiers are ultra-low voltage noise, high speed, low power consumption voltage feedback amplifiers. * 670MHz -3dB bandwidth Both amplifiers are stable at gains as low as 10. Not only do these devices find perfect application in high gain applications, they maintain their performance down to lower gain settings. Applications These amplifiers are available in SBDIP packages. All parts are specified for operation over the -55C to +125C temperature range. * Filter Ordering Information * DAC buffers PART NUMBER PART MARKING TEMP (C) PACKAGE PKG. DWG. # 5962-0623601QPC 5962-0623 601QPC -55 to +125 8 Ld SBDIP D8.3 5962-0623602QPC 5962-0623 602QPC -55 to +125 8 Ld SBDIP D8.3 FN6473.1 * Ultra low noise 0.9nV/Hz * 1000V/s slew rate * Low supply current = 16mA * Single supplies from 5V to 12V * Dual supplies from 2.5V to 6V * Fast disable on the 5962-0623601QPC * Pre-amplifier * Receiver * IF and baseband amplifier * ADC drivers * Instrumentation * Communications devices. Pinouts 5962-0623601QPC (8 LD SBDIP) TOP VIEW NC 1 IN- 2 IN+ 3 8 CE + VS- 4 7 VS+ 6 OUT 5 NC 5962-0623602QPC (8 LD SBDIP) TOP VIEW NC 1 IN- 2 IN+ 3 VS- 4 1 8 NC + 7 VS+ 6 OUT 5 NC CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2007, 2011. All Rights Reserved All other trademarks mentioned are the property of their respective owners. 5962-0623601, 5962-0623602 Absolute Maximum Ratings (TA = +25C) Supply Voltage from VS+ to VS- . . . . . . . . . . . . . . . . . . . . . . . Slewrate between VS+ and VS- . . . . . . . . . . . . . . . . . . . . . . . . IIN-, IIN+, CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Information Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C Ambient Operating Temperature . . . . . . . . . . . . . . .-55C to +125C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192mW 13.2V 1V/s 5mA 20mA CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER VS+ = +5V, VS- = -5V, RL = 500, RF = 10k, RG = 100, TA = +25C, unless otherwise specified. DESCRIPTION CONDITIONS RIN Input Resistance CIN Input Capacitance BW -3dB Bandwidth BW 0.1dB Bandwidth GBWP Gain Bandwidth Product PM Phase Margin RL = 1k, CL = 6pF SR Slew Rate RL = 100, VOUT = 2.5V tR, tF Rise Time, Fall Time OS Overshoot tS 0.01% Settling Time dG Differential Gain dP MIN Common mode TYP MAX UNIT 5 M 2 pF RF = 225, AV = +10, RL = 1k 670 MHz RF = 225, AV = +10, RL = 1k 90 MHz 3000 MHz 55 1000 V/s 0.1VSTEP 2.0 ns 0.1VSTEP 10 % 6.6 ns RF = 1k, RLOAD = 150 0.01 % Differential Phase RF = 1k, RLOAD = 150 0.01 eN Input Noise Voltage f = 10kHz 0.9 nV/Hz iN Input Noise Current f = 10kHz 3.5 pA/Hz ENABLE (5962-0623601QPC Only) tEN Enable Time 220 nS tDIS Disable Time 175 nS Pin Descriptions PART 5962-0623601QPC 5962-0623602QPC PIN NAME 1, 5 1, 5, 8 NC Not connected 2 2 IN- Inverting input 3 3 IN+ Non-inverting input 4 4 VS- Negative power supply 6 6 OUT Amplifier output 7 7 VS+ Positive power supply CE Enable and disable input 8 2 FUNCTION FN6473.1 November 3, 2011 5962-0623601, 5962-0623602 Ceramic Dual-In-Line Metal Seal Packages (SBDIP) c1 -A- D8.3 MIL-STD-1835 CDIP2-T8 (D-4, CONFIGURATION C) LEAD FINISH 8 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE -DBASE METAL E b1 M (b) M -Bbbb S C A - B S (c) SECTION A-A D S D BASE PLANE Q S2 -C- SEATING PLANE A L S1 eA A A b2 b e eA/2 c aaa M C A - B S D S ccc M C A - B S D S NOTES: INCHES SYMBOL MIN MILLIMETERS MAX MIN MAX NOTES A - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 0.405 - 10.29 - E 0.220 0.310 5.59 7.87 - e 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC - eA/2 0.150 BSC 3.81 BSC - L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 5 S1 0.005 - 0.13 - 6 S2 0.005 - 0.13 - 7 90o 105o 90o 105o - aaa - 0.015 - 0.38 - 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. bbb - 0.030 - 0.76 - 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. ccc - 0.010 - 0.25 - M - 0.0015 - 0.038 2 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer's identification shall not be used as a pin one identification mark. 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. N 8 8 5. Dimension Q shall be measured from the seating plane to the base plane. 8 Rev. 0 4/94 6. Measure dimension S1 at all four corners. 7. Measure dimension S2 from the top of the ceramic body to the nearest metallization or lead. 8. N is the maximum number of terminal positions. 9. Braze fillets shall be concave. 10. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 11. Controlling dimension: INCH. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 3 FN6473.1 November 3, 2011