SPEC NO: DSAK2209 REV NO: V.5A DATE: APR/25/2015 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201005725
2.2x1.4mm SURFACE MOUNT LED LAMP
Part Number: AA2214SURSK Hyper Red
Features
z2.2mm x 1.4mm, 1.3mm high.
zLow power consumption.
zAvailable on tape and reel.
zPackage : 2000pcs / reel.
zMoisture sensitivity level : level 3.
zRoHS compliant.
Description
The Hyper Red source color devices are made with Al-
GaInP on GaAs substrate Light Emitting Diode.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.2(0.008") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAK2209 REV NO: V.5A DATE: APR/25/2015 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201005725
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
SPEC NO: DSAK2209 REV NO: V.5A DATE: APR/25/2015 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201005725
Selection Guide
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Note:
1. 1 / 10 Duty Cycle, 0.1ms Pulse Width.
Part No. Dice Lens Type
Iv (mcd) [2]
@ 20mA
V
iewing
Angle [1]
Min. Typ. 2θ1/2
Hyper Red (AlGaInP) Water Clear
180 350
120°
*55 *100
AA2214SURSK
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Hyper Red 645 nm IF=20mA
λD [1] Dominant Wavelength Hyper Red 630 nm IF=20mA
Δλ1/2 Spectral Line Half-width Hyper Red 28 nm IF=20mA
C Capacitance Hyper Red 35 pF VF=0V;f=1MHz
VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA
IR Reverse Current Hyper Red 10 uA VR=5V
Parameter Hyper Red Units
Power dissipation 75 mW
DC Forward Current 30 mA
Peak Forward Current [1] 185 mA
Reverse Voltage 5 V
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
Notes:
1. θ1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value.
2. Luminous intensity / luminous Flux: + / -15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Notes:
1. Wavelength: + / -1nm.
2. Forward Voltage: + / -0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
SPEC NO: DSAK2209 REV NO: V.5A DATE: APR/25/2015 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201005725
Hyper Red AA2214SURSK
SPEC NO: DSAK2209 REV NO: V.5A DATE: APR/25/2015 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201005725
AA2214SURSK
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAK2209 REV NO: V.5A DATE: APR/25/2015 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201005725
PACKING & LABEL SPECIFICATIONS AA2214SURSK
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
