Rev 0; 7/03 3.3V Spread-Spectrum EconOscillator The DS1087L is a clock generator that produces a spread-spectrum (dithered) square-wave output of frequencies from 130kHz to 66.6MHz. The DS1087L is shipped from the factory programmed at a specific frequency and spread-spectrum percentage. The user still has access to an internal frequency divider, selectable 2% or 4% dithered output, and programmable output power-down/disable mode through a 2-wire programming interface. All the device settings are stored in nonvolatile (NV) EEPROM allowing it to operate in stand-alone applications. The DS1087L has powerdown and output-enable control pins for power-sensitive applications. Applications Printers Features Factory Programmed Square-Wave Generator from 130kHz to 66.6MHz No External Timing Components Required EMI Reduction 2.7V to 3.6V Supply User Programmable Down to 130kHz with Divider (Dependent on Master Oscillator Frequency) 2% or 4% Selectable Dithered Output Glitchless Output-Enable Control 2-Wire Serial Interface Nonvolatile Settings Power-Down Mode Programmable Output Power-Down/Disable Mode Copiers PCs Computer Peripherals Ordering Information Cell Phones PART Cable Modems DS1087LU-yxx TEMP RANGE PIN-PACKAGE -40C to +85C 8 SOP (118 mils) Pin Configuration Standard Frequency Options PART FREQUENCY (MHz) SPREAD (%) DS1087LU-202 2.0480 2 DS1087LU-402 2.0480 4 DS1087LU-210 10.0 2 DS1087LU-216 16.6 2 DS1087LU-266 66.6 2 DS1087LU-466 66.6 4 DS1087LU-yxx Fixed up to 66.6 2 or 4 Custom frequencies and over 20 standard frequencies available, contact factory. TOP VIEW OUT 1 8 SCL 7 SDA 3 6 PDN GND 4 5 OE SPRD 2 DS1087L VCC SOP (118 mils) EconOscillator is a trademark of Dallas Semiconductor. Typical Operating Circuits appear at end of data sheet. ______________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 DS1087L General Description DS1087L 3.3V Spread-Spectrum EconOscillator ABSOLUTE MAXIMUM RATINGS Voltage Range on VCC Relative to Ground ..........-0.5V to +6.0V Voltage Range on SPRD, PDN, OE, SDA, SCL Relative to Ground* ................................-0.5V to (VCC + 0.5V) Operating Temperature Range ...........................-40C to +85C *This voltage must not exceed 6.0V. Programming Temperature Range .........................0C to +70C Storage Temperature Range .............................-55C to +125C Soldering Temperature ..................See IPC/JEDEC J-STD-020A Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED DC OPERATING CONDITIONS (VCC = 2.7V to 3.6V, TA = -40C to +85C.) PARAMETER Supply Voltage High-Level Input Voltage (SDA, SCL, SPRD, PDN, OE) Low-Level Input Voltage (SDA, SCL, SPRD, PDN, OE) SYMBOL VCC CONDITION (Note 1) MIN TYP MAX UNITS 2.7 3.6 V VIH 0.7 x VCC VCC + 0.3 V VIL -0.3 0.3 x VCC V MAX UNITS DC ELECTRICAL CHARACTERISTICS (VCC = 2.7V to 3.6V, TA = -40C to +85C.) PARAMETER SYMBOL High-Level Output Voltage (OUT) VOH IOH = -4mA, VCC = min Low-Level Output Voltage (OUT) Low-Level Output Voltage (SDA) CONDITION V VOL IOL = 4mA 3mA sink current 0 0.4 VOL2 6mA sink current 0 0.6 IIH VCC = 3.6V Low-Level Input Current IIL VIL = 0 Supply Current (Active) ICC 2 TYP 2.4 VOL1 High-Level Input Current Standby Current (Power-Down) MIN ICCQ 0.4 V V 1 A CL = 15pF (output at f0) 15 mA Power-down mode 5 A _____________________________________________________________________ -1 A 3.3V Spread-Spectrum EconOscillator (VCC = 2.7V to 3.6V, TA = -40C to +85C.) PARAMETER Master Oscillator Range Available SYMBOL CONDITION f0 MIN TYP MAX UNITS 33.3 66.6 MHz Master Oscillator Frequency Tolerance f0 f0 VCC = 3.3V, TA = +25C (Note 2) -0.5 +0.5 % Voltage Frequency Variation fV f0 Over voltage range, TA = +25C (Note 3) -0.75 +0.75 % Temperature Frequency Variation fT f0 0C to +70C, VCC = 3.3V (Note 4) -0.5 +0.5 % Temperature Frequency Variation fT f0 -40C to +85C, VCC = 3.3V (Note 4) -1.5 +0.5 % Dither Frequency Range Prescaler bit J0 = 1 (Note 5) 2 Prescaler bit J0 = 0 (Note 5) 4 Dither Rate % f0 / 2048 Hz AC ELECTRICAL CHARACTERISTICS (VCC = 2.7V to 3.6V, TA = -40C to +85C.) PARAMETER SYMBOL CONDITION MIN TYP Frequency Stable After PRESCALER Change MAX UNITS 1 period 0.5 ms Power-Up Time tPOR + tSTAB Enable of OUT After Exiting Power-Down Mode tSTAB 500 s OUT Disabled After Entering Power-Down Mode tPDN 1 ms 50 pF 55 % Load Capacitance Output Duty Cycle (OUT) CL (Note 6) 0.1 (Note 7) TA = +25C 15 45 _____________________________________________________________________ 3 DS1087L MASTER OSCILLATOR CHARACTERISTICS DS1087L 3.3V Spread-Spectrum EconOscillator AC ELECTRICAL CHARACTERISTICS--2-WIRE INTERFACE (VCC = 2.7V to 3.6V, TA = 0C to +70C.) PARAMETER SYMBOL SCL Clock Frequency fSCL Bus Free Time Between a STOP and START Condition tBUF Hold Time (repeated) START Condition tHD:STA LOW Period of SCL tLOW HIGH Period of SCL tHIGH Setup Time for a Repeated START tSU:STA Data Hold Time tHD:DAT Data Setup Time tSU:DAT Rise Time of Both SDA and SCL Signals tR Fall Time of Both SDA and SCL Signals tF Setup Time for STOP tSU:STO Capacitive Load for Each Bus CB NV Write Cycle Time tWR Input Capacitance CONDITION MIN TYP MAX Fast mode (Note 8) 400 Standard mode (Note 8) 100 Fast mode (Note 8) 1.3 Standard mode (Note 8) 4.7 Fast mode (Notes 8 and 9) 0.6 Standard mode (Notes 8 and 9) 4.0 Fast mode (Note 8) 1.3 Standard mode (Note 8) 4.7 Fast mode (Note 8) 0.6 Standard mode (Note 8) 4.0 Fast mode 0.6 Standard mode 4.7 s s s s 0 0.9 Standard mode (Notes 8, 10, and 11) 0 0.9 100 Standard mode (Note 8) 250 20 + 0.1CB 300 Standard mode (Note 12) 20 + 0.1CB 1000 Fast mode (Note 12) 20 + 0.1CB 300 Standard mode (Note 12) 20 + 0.1CB 1000 0.6 Standard mode 4.0 ns ns s (Note 12) CI s ns Fast mode (Note 12) Fast mode kHz s Fast mode (Notes 8, 10, and 11) Fast mode (Note 8) UNITS 400 pF 10 ms 5 pF NONVOLATILE MEMORY CHARACTERISTICS (VCC = 2.7V to 3.6V) PARAMETER Writes 4 SYMBOL CONDITION +70C _____________________________________________________________________ MIN 10,000 TYP MAX UNITS 3.3V Spread-Spectrum EconOscillator Note 4: Note 5: Note 6: Note 7: Note 8: Note 9: Note 10: Note 11: Note 12: All voltages are referenced to ground. This is the absolute accuracy of the master oscillator frequency at the default settings. This is the change that is observed in master oscillator frequency with changes in voltage from nominal voltage at TA = +25C. This is the percentage frequency change from the +25C frequency due to temperature at VCC = 3.3V. The dither deviation of the master oscillator frequency is unidirectional and lower than the undithered frequency. This indicates the time elapsed between power-up and the output becoming active. An on-chip delay is intentionally introduced to allow the oscillator to stabilize. tstab is equivalent to approximately 512 master clock cycles and depends on the programmed master oscillator frequency. Output voltage swings may be impaired at high frequencies combined with high output loading. A fast-mode device can be used in a standard-mode system, but the requirement tSU:DAT > 250ns must then be met. This is automatically the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line at least tR MAX + tSU:DAT = 1000ns + 250ns = 1250ns before the SCL line is released. After this period, the first clock pulse is generated. A device must internally provide a hold time of at least 300ns for the SDA signal (referred to as the VIH MIN of the SCL signal) to bridge the undefined region of the falling edge of SCL. The maximum tHD:DAT need only be met if the device does not stretch the LOW period (tLOW) of the SCL signal. CB--total capacitance of one bus line, timing referenced to 0.9 x VCC and 0.1 x VCC. Typical Operating Characteristics (VCC = 3.3V, TA = +25C, unless otherwise noted.) 6.0 15pF LOAD 6.0 5.5 8.2pF LOAD 4.7pF LOAD FREQUENCY = 66.6MHz OUTPUT UNLOADED OE = PDN = VCC 5.0 OUTPUT UNLOADED 6 5 5.0 4.0 3.0 4 3 3.6V 3.3V 2.7V 2 2.0 1 1.0 UNLOADED DS1087L toc03 7.0 SUPPLY CURRENT vs. PRESCALER 7 CURRENT (mA) 6.5 VCC = 3.3V FREQUENCY = 66.6MHz OE = PDN = VCC CURRENT (mA) CURRENT (mA) 7.0 8.0 DS1087L toc01 7.5 ACTIVE SUPPLY CURRENT vs. VOLTAGE DS1087L toc02 ACTIVE SUPPLY CURRENT vs. TEMPERATURE 0 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 TEMPERATURE (C) VOLTAGE (V) 1 10 100 1000 PRESCALER (DECIMAL) _____________________________________________________________________ 5 DS1087L Note 1: Note 2: Note 3: Typical Operating Characteristics (VCC = 3.3V, TA = +25C, unless otherwise noted.) SUPPLY CURRENT vs. TEMPERATURE WITH OE = 0 3.5 2.0 DS1087L toc05 VCC = 3.3V OUPUT UNLOADED VCC = 2.7V OUTPUT UNLOADED 1.6 3 -40C, +25C, +85C 1.4 CURRENT (A) CURRENT (mA) 2.5 FREQUENCY = 66.6MHz 2.0 1.5 2 FREQUENCY = 206.4kHz 10 100 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 PRESCALER (DECIMAL) TEMPERATURE (C) TEMPERATURE (C) FREQUENCY % CHANGE vs. SUPPLY VOLTAGE FREQUENCY % CHANGE vs. TEMPERATURE ACTIVE SUPPLY CURRENT vs. SCL FREQUENCY 0.20 0 -0.20 -0.40 -0.60 7 DS1087L toc08 1.00 VCC = 3.3V FREQUENCY = 66.6MHz OUTPUT LOADED WITH 12pF OSCILLOSCOPE PROBE 0.50 0 -0.50 -1.00 -1.50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 VOLTAGE (V) TEMPERATURE (C) DUTY CYCLE vs. VOLTAGE 57 56 55 54 0 100 58 57 56 55 54 53 52 52 51 51 50 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 VOLTAGE (V) 0 200 300 SCL FREQUENCY (kHz) VCC = 3.3V FREQUENCY = 66.6MHz OUTPUT LOADED WITH 12pF OSCILLOSCOPE PROBE 59 53 50 6 2 DUTY CYCLE vs. TEMPERATURE DUTY CYCLE (%) DUTY CYCLE (%) 58 FREQUENCY = 66.6MHz TA = +25C OUTPUT LOADED WITH 12pF OSCILLOSCOPE PROBE 3 60 DS1087L toc10 59 4 0 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 60 5 1 -0.80 -1.00 VCC = SDA = 3.3V FREQUENCY = 66.6MHz OUTPUT UNLOADED 6 SUPPLY CURRENT (mA) 0.40 1.50 FREQUENCY % CHANGE (FROM 25C) OUTPUT LOADED WITH 12pF OSCILLOSCOPE PROBE FREQUENCY = 66.6MHz DS1087L toc07 0.60 1000 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 1.00 0.80 0.2 0 1 0.8 0.4 0.5 0 1.0 0.6 1.0 1 1.2 DS1087L toc09 CURRENT (mA) 3.0 4 VCC = 3.3V OUTPUT UNLOADED 1.8 DS1087L toc11 5 4.0 DS1087L toc04 6 SHUTDOWN SUPPLY CURRENT vs. TEMPERATURE DS1087L toc06 SUPPLY CURRENT vs. PRESCALER FREQUENCY % CHANGE (FROM 3.3V) DS1087L 3.3V Spread-Spectrum EconOscillator 10 20 30 40 50 TEMPERATURE (C) _____________________________________________________________________ 60 70 400 3.3V Spread-Spectrum EconOscillator PIN NAME FUNCTION 1 OUT Oscillator Output 2 SPRD Dither Enable. When the pin is high, the dither is enabled. When the pin is low, the dither is disabled. 3 VCC 4 GND Power Supply Ground 5 OE Output Enable. When the pin is high, the output buffer is enabled. When the pin is low, the output is disabled but the internal master oscillator is still on. 6 PDN Power-Down. When the pin is high, the master oscillator is enabled. When the pin is low, the master oscillator is disabled (power-down mode). 7 SDA 2-Wire Serial Data. This pin is for serial data transfer to and from the device. 8 SCL 2-Wire Serial Clock. This pin is used to clock data into and out of the device. VCC SDA SCL EEPROM CONTROL REGISTERS 2-WIRE INTERFACE DS1087L ADDR PRESCALER FACTORY-PROGRAMMED OSCILLATOR PDN MASTER OSCILLATOR OUTPUT DITHER CONTROL PRESCALER BY 1, 2, 4...256 OUT OE SPRD GND TRIANGLE WAVE GENERATOR DITHER SIGNAL Figure 1. Functional Diagram _____________________________________________________________________ 7 DS1087L Pin Description DS1087L 3.3V Spread-Spectrum EconOscillator Table 1. Register Summary REGISTER ADDR BINARY PRESCALER 02h X1 X1 LO/ HIZ ADDR 0Dh X1 X1 X1 WRITE EE 3Fh J0 P3 P2 P1 X1 WC A2 A1 FACTORY DEFAULT ACCESS P0 110- - - - - b R/W A0 11110000b R/W -- -- No Data X1 = Don't care; read as one. Detailed Description A block diagram of the DS1087L is shown in Figure 1. Output Frequency The internal master oscillator can generate a square wave with a frequency range of 33.3MHz to 66.6MHz. The master oscillator frequency and output frequency are factory programmed, although the user can use the programmable divider to divide the master oscillator frequency by 2x (where x equals 0 to 8). Output Control and Power-Down Two user control signals control the output. The outputenable pin, OE, gates the clock output buffer and the PDN pin disables the master oscillator and turns off the output for power-sensitive applications (note: the power-down command must persist for at least two output frequency cycles plus 10s for deglitching purposes). On power-up, the output is disabled until power is stable and the master oscillator has generated 512 clock cycles. Both controls feature a synchronous enable, which ensures there are no output glitches when the output is enabled. The synchronous enable also ensures a constant time interval (for a given frequency setting) from an enable signal to the first output transition. Spread Spectrum The DS1087L can reduce radiated emission peaks. The output frequency can be dithered 2% or 4% below the programmed frequency. Although the output frequency changes when the dither is enabled, the duty cycle does not change. The dither is controlled by the J0 bit in the PRESCALER register and enabled with the SPRD pin. The maximum spectral attenuation occurs when the prescaler is set to 1. The spectral attenuation is reduced by 2.7dB for every factor of 2 that is used in the prescaler. This happens because the prescaler's divider function tends to average the dither in creating the lower frequency. However, the most stringent spectral emission limits are imposed on the higher frequencies where the prescaler is set to a low divider ratio. A triangle-wave generator injects an offset element into the master oscillator to dither its output. The dither rate (see Equation 1) is based on the master oscillator frequency. Figure 2 shows a plot of the output frequency versus dither rate. Dither Rate = (1) where f0 = master oscillator frequency Register Summary The DS1087L registers are used to change the dither amount, output frequency, and slave address. A summary of the registers is shown in Table 1. Once programmed into EEPROM, the settings only need to be reprogrammed if it is desired to reconfigure the device. PRESCALER Register OUTPUT FREQUENCY Bit 5: fO/N (fO/N) - 4% 0 fO/2048 DITHER RATE 2fO/2048 Bit 4: WHERE N = (2X) f0 = FACTORY PROGRAMMED MASTER OSCILLATOR FREQUENCY Figure 2. Output Frequency vs. Dither Rate 8 f0 2048 Output Low or High-Z. The LO/HIZ bit controls the output. During power-down, while the output is deactivated, if the LO/HIZ bit is set to 0, the output is high-Z. If the LO/HIZ bit is set to 1, the output is driven low. Dither Control. The J0 bit controls the dither applied to the output. When J0 is high, 2% peak dither is selected. When J0 is low, 4% peak dither is selected. _____________________________________________________________________ 3.3V Spread-Spectrum EconOscillator _______2-Wire Serial Port Operation Prescaler Divider. The prescaler bits (bits P3 to P0) divide the master oscillator frequency by 2x where x can be from 0 to 8. Any prescaler bit value entered that is greater than 8 decodes as 8. 2-Wire Serial Data Bus The DS1087L communicates through a 2-wire serial interface. A device that sends data onto the bus is defined as a transmitter, and a device receiving data as a receiver. The device that controls the message is called a "master." The devices that are controlled by the master are "slaves." A master device that generates the serial clock (SCL), controls the bus access, and generates the START and STOP conditions must control the bus. The DS1087L operates as a slave on the 2-wire bus. Connections to the bus are made through the open-drain I/O lines SDA and SCL. The following bus protocol has been defined (see Figures 3 and 5): ADDR Register Bit 3: Bits 2 to 0: Write Control. The WC bit determines if the EEPROM is to be written to after register contents have been changed. If WC = 0 (default), EEPROM is written automatically after a write. If WC = 1, the EEPROM is only written when the WRITE EE command is issued. See the WRITE EE Command section for more information. Address. The A0, A1, A2 bits determine the lower nibble of the 2-wire slave address. * WRITE EE Command * The WRITE EE command is useful in closed-loop applications where the registers are frequently written. In applications where the register contents are frequently written, the WC bit should be set to 1 to prevent wearing out the EEPROM. Regardless of the value of the WC bit, the value of the ADDR register is always written immediately to EEPROM. When the WRITE EE command has been received, the contents of the registers are copied into the EEPROM, thus locking in the register settings. Data transfer can be initiated only when the bus is not busy. During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in the data line while the clock line is HIGH are interpreted as control signals. Accordingly, the following bus conditions have been defined: Bus not busy: Both data and clock lines remain HIGH. Start data transfer: A change in the state of the data line, from HIGH to LOW, while the clock is HIGH, defines a START condition. Stop data transfer: A change in the state of the data line, from LOW to HIGH, while the clock line is HIGH, defines the STOP condition. SDA MSB SLAVE ADDRESS R/W DIRECTION BIT ACKNOWLEDGEMENT SIGNAL FROM RECEIVER ACKNOWLEDGEMENT SIGNAL FROM RECEIVER SCL 1 2 START CONDITION 6 7 8 9 1 2 3-7 8 ACK 9 ACK REPEATED IF MORE BYTES ARE TRANSFERRED STOP CONDITION OR REPEATED START CONDITION Figure 3. 2-Wire Data Transfer Protocol _____________________________________________________________________ 9 DS1087L Bits 3 to 0: MSB A2 A1 DEVICE ADDRESS A0 R/W IT 1 D/W DEVICE IDENTIFIER 1 EB 0 RIT 1 LSB RE A DS1087L 3.3V Spread-Spectrum EconOscillator Figure 4. Slave Address Data valid: The state of the data line represents valid data when, after a START condition, the data line is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed during the LOW period of the clock signal. There is one clock pulse per bit of data. Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of data bytes transferred between START and STOP conditions is not limited, and is determined by the master device. The information is transferred byte-wise and each receiver acknowledges with a ninth bit. Within the bus specifications a standard mode (100kHz clock rate) and a fast mode (400kHz clock rate) are defined. The DS1087L works in both modes. Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after the byte has been received. The master device must generate an extra clock pulse that is associated with this acknowledge bit. A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a way that the SDA line is stable LOW during the HIGH period of the acknowledge-related clock pulse. Of course, setup and hold times must be taken into account. When the DS1087L EEPROM is being written to, it is not able to perform additional responses. In this case, the slave DS1087L sends a not acknowledge to any data transfer request made by the master. It resumes normal operation when the EEPROM operation is complete. A master must signal an end of data to the slave by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case, the slave must leave the data line HIGH to enable the master to generate the STOP condition. 10 Figures 3, 4, 5, and 6 detail how data transfer is accomplished on the 2-wire bus. Depending upon the state of the R/W bit, two types of data transfer are possible: 1) Data transfer from a master transmitter to a slave receiver. The first byte transmitted by the master is the slave address. Next follows a number of data bytes. The slave returns an acknowledge bit after each received byte. 2) Data transfer from a slave transmitter to a master receiver. The first byte (the slave address) is transmitted by the master. The slave then returns an acknowledge bit. Next follows a number of data bytes transmitted by the slave to the master. The master returns an acknowledge bit after all received bytes other than the last byte. At the end of the last received byte, a not acknowledge is returned. The master device generates all the serial clock pulses and the START and STOP conditions. A transfer is ended with a STOP condition or with a repeated START condition. Since a repeated START condition is also the beginning of the next serial transfer, the bus is not released. The DS1087L can operate in the following two modes: Slave receiver mode: Serial data and clock are received through SDA and SCL. After each byte is received, an acknowledge bit is transmitted. START and STOP conditions are recognized as the beginning and end of a serial transfer. Address recognition is performed by hardware after reception of the slave address and direction bit. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode. However, in this mode, the direction bit indicates that the transfer direction is reversed. Serial data is transmitted on SDA by the DS1087L while the serial clock is input on SCL. START and STOP conditions are recognized as the beginning and end of a serial transfer. Slave Address Figure 4 shows the first byte sent to the device. It includes the device identifier, device address, and the R/W bit. The device address must match the address set in the ADDR register (bits A0, A1, and A2). Registers/Commands See Table 1 for the complete list of registers/commands and Figure 6 for an example of using them. ____________________________________________________________________ 3.3V Spread-Spectrum EconOscillator DS1087L SDA tBUF tSP tHD:STA tLOW tR tF SCL tHD:STA STOP tSU:STA tHIGH tSU:DAT START REPEATED START tSU:STO tHD:DAT Figure 5. 2-Wire AC Characteristics TYPICAL 2-WIRE WRITE TRANSACTION MSB START 1 LSB 0 1 1 DEVICE IDENTIFIER MSB SLAVE ACK A2* A1* A0* R/W DEVICE ADDRESS READ/ WRITE b7 b5 b4 b3 b2 b1 b0 B0h START 1 0 1 1 0 0 0 0 SLAVE ACK b7 COMMAND/REGISTER ADDRESS EXAMPLE 2-WIRE TRANSACTIONS (WHEN A0, A1, AND A2 ARE ZERO) B0h 02h DATA SLAVE SLAVE A) SINGLE BYTE WRITE 10000000 START 1 0 1 1 0 0 0 0 ACK 0 0 0 0 0 0 1 0 ACK -WRITE PRESCALER REGISTER TO 128 B) SINGLE BYTE READ -READ PRESCALER REGISTER MSB LSB b6 02h SLAVE SLAVE 00000010 ACK ACK b5 b4 b3 b2 b1 b0 SLAVE ACK STOP DATA SLAVE ACK STOP B1h REPEATED START LSB b6 10110001 DATA MASTER SLAVE 10000000 NACK ACK STOP *THE ADDRESS DETERMINED BY A0, A1, AND A2 MUST MATCH THE ADDRESS SET IN THE ADDR REGISTER. Figure 6. 2-Wire Transactions Application Information Power-Supply Decoupling To achieve the best results when using the DS1087L, decouple the power supply with 0.01F and 0.1F high-quality, ceramic, surface-mount capacitors. Surface-mount components minimize lead inductance, which improves performance, and ceramic capacitors tend to have adequate high-frequency response for decoupling applications. These capacitors should be placed as close to the VCC and GND pins as possible. Stand-alone Mode SCL and SDA cannot be left floating even in standalone mode. If the DS1087L never needs to be programmed in-circuit, including during production testing, SDA and SCL can be wired high. ____________________________________________________________________ 11 DS1087L 3.3V Spread-Spectrum EconOscillator Typical Operating Circuits Stand-Alone Mode Processor-Controlled Mode VCC MICROPROCESSOR 4.7k DITHERED 130kHz TO 66.6MHz OUTPUT VCC 4.7k XTL1/OSC1 XTL2/OSC2 SCL OUT SPRD SDA DS1087L VCC PDN GND OE VCC 2-WIRE INTERFACE VCC DITHERED 130kHz TO 66.6MHz OUTPUT VCC N.C. SCL* OUT SPRD DS1087L SDA* VCC PDN GND OE DECOUPLING CAPACITORS (0.1F and 0.01F) *SDA AND SCL CAN BE CONNECTED DIRECTLY HIGH IF THE DS1087L NEVER NEEDS TO BE PROGRAMMED IN-CIRCUIT, INCLUDING DURING PRODUCTION TESTING. DECOUPLING CAPACITORS (0.1F and 0.01F) Chip Topology TRANSISTOR COUNT: 10000 SUBSTRATE CONNECTED TO GROUND Package Information For the latest package outline information, go to www.maxim-ic.com/DallasPackInfo Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.