THIS PAGE INTENTIONALLY LEFT BLANK
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 1
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
Functional Diagram
Features
• Tri-band RF Bandwidths:
1050 - 1205,
2100 - 2410, 4200 - 4820 MHz
• Ultra Low Phase Noise
-112 dBc/Hz in Band Typ.
• Figure of Merit (FOM) -227 dBc/Hz
• < 180 fs RMS Jitter
• 24-bit Step Size, Resolution 3 Hz typ
• Exact Frequency Resolution Mode
• Built-In Digital Self Test
• 40 Lead 6x6 mm SMT Package: 36 mm2
Typical Applications
• Cellular/4G Infrastructure
• Repeaters and Femtocells
• Communications Test Equipment
• CATV Equipment
• Phased Array Applications
• DDS Replacement
• Very High Data Rate Radios
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 2
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
General Description
The HMC839LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) with an Integrated Voltage Controlled
Oscillator (VCO). The PLL consists of an integrated low noise VCO with a tri-band output, an autocalibration subsystem
for low voltage VCO tuning, a very low noise digital Phase Detector (PD), a precision controlled charge pump, a low
noise reference path divider and a fractional divider.
The fractional PLL features an advanced delta-sigma modulator design that allows both ultra-ne step sizes and
low spurious products. The phase detector (PD) features cycle slip prevention (CSP) technology to allow fas-
ter frequency hopping times. Ultra low in-close phase noise and low spurious also allows wider loop bandwidths for
faster frequency hopping and low micro-phonics.
For theory of operation and register map refer to the “PLLs with Integrated VCOs - RF VCOs Operating Guide”. To
view the Operating Guide, please visit www.hittite.com and choose HMC839LP6CE from the “Search by Part
Number” pull down menu.
Parameter Condition Min. Typ. Max. Units
RF Output Characteristics
VCO Frequency at PLL Input 2100 2200 2410 MHz
RF Output Frequency at fVCO/2 1050 110 0 1205 MHz
RF Output Frequency at fVCO 2100 2200 2410 MHz
RF Output Frequency at 2fVCO 4200 4400 4820 MHz
RF Output Power at fVCO/2 7. 5 10 12.5 dBm
RF Output Power at fVCO 3.5 712 dBm
RF Output Power at 2fVCO -9 -4 1dBm
VCO Tuning Sensitivity Measured at fo, 2V (N= 0/15/31) 10 13 18 MHz/V
VCO Supply Pushing Measured at fo, 2V 1.6 MHz/V
RF Output fo/2 Harmonic Doubler Mode -26 dBc
RF Output 3fo/2 Harmonic Doubler Mode -35 dBc
RF Output 2nd Harmonic fo/2/fo/2fo -23 / -28 / -41 dBc
RF Output 5fo/2 Harmonic Doubler Mode -48 dBc
RF Output 3rd Harmonic fo/2/fo/2fo -30 / -34 / -55 dBc
RF Output 7fo/2 Harmonic Doubler Mode -55 dBc
RF Output 4th Harmonic fo/2/fo/2fo -32 / -52 / -58 dBc
RF Divider Characteristics
19-Bit N-Divider Range (Integer) Max = 219 - 1 16 524,287
19-Bit N-Divider Range (Fractional) Fractional nominal divide ratio
varies (-3 / +3) dynamically max 20 524,283
REF Input Characteristics
Ref Input Frequency
Synthesizer phase noise can
degrade by about 5dB when operat-
ing with a reference frequency near
the low end of this range.
10 50 200 MHz
Ref Input Range AC Coupled 1 2 3.3 Vp-p
Ref Input Capacitance 5pF
14-Bit R-Divider Range 116,383
Electrical Specications, TA = +25° C, VPPCP, VDDCP, VCC1, VCC2 = 5V ±4%;
RVDD, AVDD, DVDD3V, VCCPD, VCCHF, VCCPS = 3.3V ±6% GNDCP = GNDLS = Ground
Paddle = 0V, 100 MHz Reference Unless Otherwise Noted.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 3
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
Parameter Condition Min. Typ. Max. Units
Phase Detector (PD)
PD Frequency Fractional Feedback Mode [1] 0.1 100 MHz
PD Frequency Fractional Feedforward
Mode (and Register 6 [17:16] = 10) 0.1 80 MHz
PD Frequency Integer Mode [1] 0.1 125 MHz
Charge Pump
Output Current 0.02 2.54 mA
Charge Pump Gain Step Size 20 µA
PD/Charge Pump SSB Phase Noise Input Referred, Maximum CP Cur-
rent
100 Hz -132 dBc/Hz
1 kHz -142 dBc/Hz
10 kHz Add 1 dB for Fractional -151 -149 -147 dBc/Hz
100 kHz Add 3 dB for Fractional -155 -153 -151 dBc/Hz
Logic Inputs
VIH Output High Voltage DVDD3V-0.4 DVDD3V V
VIL Output Low Voltage 00.4 V
Logic Outputs
VOH Output High Voltage DVDD3V-0.4 DVDD3V V
VOL Output Low Voltage 00.4 V
Power Supply Voltages
Analog 3.3V Supplies AVDD, VCCHF, VCCPS, VCCPD,
RVDD 3.0 3.3 3.5 V
Digital Supply DVDD3V 3.0 3.3 3.5 V
Analog 5V Supplies VPPCP, VDDCP, VCC1, VCC2 4.8 55.2 V
Power Supply Currents
+5V Analog Charge Pump VPPCP, VDDCP 5.3 mA
+5V VCO, PLL Buffer and RF Buffer VCC1 + VCC2 (fo / 2 / fo / 2fo) 89 / 73 / 72 mA
+3.3V Analog AVDD, VCCHF, VCCPS, VCCPD,
RVDD 45 mA
+3.3V Digital DVDD3V 6.5 mA
Power Down - Crystal Off Reg 01h=0, Crystal Not Clocked 10 µA
Power Down - Crystal On, 100 MHz Reg 01h=0, Crystal Clocked 100
MHz 10 200 µA
Power on Reset
Typical Reset Voltage on DVDD 700 mV
Min DVDD Voltage for No Reset 1.5 V
Power on Reset Delay 250 µs
VCO Open Loop Phase Noise at fo/2
10 kHz Offset -91 dBc/Hz
100 kHz Offset -121 dBc/Hz
1 MHz Offset -146 dBc/Hz
Electrical Specications (Continued)
Note 1: This maximum phase detector frequency can only be achieved if the minimum N value is respected. eg. In the case of fractional feedback
mode, the maximum PFD rate = fvco/20 or 100 MHz, whichever is less.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 4
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
Electrical Specications (Continued)
Parameter Condition Min. Typ. Max. Units
10 MHz Offset -162 dBc/Hz
100 MHz Offset -163 dBc/Hz
VCO Open Loop Phase Noise at fo
10 kHz Offset -85 dBc/Hz
100 kHz Offset -116 dBc/Hz
1 MHz Offset -140 dBc/Hz
10 MHz Offset -161 dBc/Hz
100 MHz Offset -166 dBc/Hz
VCO Open Loop Phase Noise at 2fo
10 kHz Offset -80 dBc/Hz
100 kHz Offset -109 dBc/Hz
1 MHz Offset -135 dBc/Hz
10 MHz Offset -155 dBc/Hz
100 MHz Offset -158 dBc/Hz
Closed Loop Phase Noise PLL + VCO at fvco/2
Integer, 100 MHz PD 1 kHz Offset -117 dBc/Hz
Integer, 100 MHz PD 10 kHz Offset -121 dBc/Hz
Integer, 100 MHz PD 100 kHz Offset -121 dBc/Hz
Fractional, 100 MHz PD 1 kHz Offset -113 dBc/Hz
Fractional, 100 MHz PD 10 kHz Offset -116 dBc/Hz
Fractional, 100 MHz PD 100 kHz Offset -117 dBc/Hz
Closed Loop Phase Noise PLL + VCO at fvco
Integer, 100 MHz PD 1 kHz Offset -109 dBc/Hz
Integer, 100 MHz PD 10 kHz Offset -115 dBc/Hz
Integer, 100 MHz PD 100 kHz Offset -112 dBc/Hz
Fractional, 100 MHz PD 1 kHz Offset -106 dBc/Hz
Fractional, 100 MHz PD 10 kHz Offset -110 dBc/Hz
Fractional, 100 MHz PD 100 kHz Offset -114 dBc/Hz
Closed Loop Phase Noise PLL + VCO at 2fo
Integer, 100 MHz PD 1 kHz Offset -103 dBc/Hz
Integer, 100 MHz PD 10 kHz Offset -108 dBc/Hz
Integer, 100 MHz PD 100 kHz Offset -107 dBc/Hz
Fractional, 100 MHz PD 1 kHz Offset -100 dBc/Hz
Fractional, 100 MHz PD 10 kHz Offset -104 dBc/Hz
Fractional, 100 MHz PD 100 kHz Offset -106 dBc/Hz
Synthesizer Figure of Merit Normalized 1 Hz
Integer Mode Measured w/ 50 MHz PD at
30 kHz Offset -229 dBc/Hz
Fractional Mode Measured w/ 50 MHz PD at
30 kHz Offset -227 dBc/Hz
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 5
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
[1] Fractional Mode, 100 MHz Crystal, R=1
Typical Closed Loop
Fractional Phase Noise [1]
Free Running Phase Noise Typical Tuning Curves vs. Switch Position
Free Running VCO Phase Noise
Over Temperature
Typical VCO Tuning Voltage
After Calibration
Closed Loop Integer Phase Noise
-170
-150
-130
-110
-90
-70
1000 104105106107108
FREQUENCY OFFSET(Hz)
PHASE NOISE (dBc/Hz)
1100MHz
2200MHz
4400MHz
-170
-150
-130
-110
-90
-70
1000 104105106107108
FREQUENCY OFFSET (Hz)
PHASE NOISE (dBc/Hz)
1102MHz
2193MHz
4377MHz
-180
-160
-140
-120
-100
-80
-60
-40
-20
0
103104105106107108
OFFSET FREQUENCY (Hz)
PHASE NOISE (dBc/Hz)
1102MHz
4377MHz
2193MHz
900
950
1000
1050
1100
012345
TUNING VOLTAGE (V)
KVCO (MHz/V)
n2
n4n6
n8
n10
n12
n14n16
n18
n20 n22
n24 n26
fmax
fmin
fmax
n30
n0
n31
-170
-160
-150
-140
-130
-120
-110
+27C
+85C
-40C
2050 2100 2150 2200 2250 2300 2350 2400 2450
PHASE NOISE (dBc/Hz)
FREQUENCY (MHz)
1 MHz Offset
100 kHz Offset
10 MHz Offset
0
1
2
3
4
5
2000 2100 2200 2300 2400 2500
VCO FREQUENCY
TUNE VOLTAGE AFTER CALIBRATION (V)
0
15
31
fmin fmax
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 6
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
Typical VCO Sensitivity vs.
Cap @ Fo Voltage
Figure of Merit
Typical Output Power -
Narrow Band Match
Typical Spurious @ 200 kHz
from Integer Boundary
0
10
20
30
40
50
60
012345
TUNING VOLTAGE (V)
KVCO (MHz/V)
+25C
Typ Operating Range
Tuning Cap 0, 2458MHz at 2V
Tuning Cap 15, 2200MHz at 2V
Tuning Cap 31, 2032MHz at 2V
-160
-140
-120
-100
-80
-60
-40
-20
0
1000 104105106107108
FREQUENCY OFFSET (Hz)
PHASE NOISE (dBc/Hz)
400kHz, -75Bc
200kHz, -76dBc
2200.200MHz
100MHz PFD Fractional Mode
200kHz Offset from Integer Boundary
70kHz Loop Bandwidth
100MHz, -99dBc
-240
-230
-220
-210
-200
100 1000 104105106
NORMALIZED PHASE NOISE (dBc/Hz)
FREQUENCY OFFSET (Hz)
FOM Floor
FOM 1/f Noise
Typ FOM vs Offset
-10
-5
0
5
10
15
20
1000 2000 3000 4000 5000
OUTPUT FREQUENCY(MHz)
OUTPUT POWER (dBm)
Divide by 2
-40C
27C
85C
Fundamental
Doubler
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 7
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
Pin Descriptions
Pin Number Function Description
1AVDD DC Power Supply for analog circuitry.
2, 5, 6, 8, 9,
11 - 14, 18 - 22, 24,
26, 34, 37, 38
N/C The pins are not connected internally; however, all data shown herein
was measured with these pins connected to RF/DC ground externally.
3VPPCP Power Supply for charge pump analog section
4CP Charge Pump Output
7VDDCP Power Supply for the charge pump digital section
10 RVDD Reference Supply
15 XREFP Reference Oscillator Input
16 DVDD3V DC Power Supply for Digital (CMOS) Circuitry
17 CEN Chip Enable. Connect to logic high for normal operation.
23 VTUNE VCO Varactor. Tuning Port Input.
25 VCC2 VCO Analog Supply 2
27 VCC1 VCO Analog Supply 1
28 RF_ N [1] RF Positive Output
29 RF_ P [1] RF Negative Output
30 SEN PLL Serial Port Enable (CMOS) Logic Input
31 SDI PLL Serial Port Data (CMOS) Logic Input
32 SCK PLL Serial Port Clock (CMOS) Logic Input
33 LD_SDO Lock Detect, or Serial Data, or General Purpose (CMOS) Logic Output (GPO)
35 VCCHF DC Power Supply for Analog Circuitry
36 VCCPS DC Power Supply for Analog Prescaler
39 VCCPD DC Power Supply for Phase Detector
40 BIAS
External bypass decoupling for precision bias circuits.
Note: 1.920V ±20mV reference voltage (BIAS) is generated internally and cannot
drive an external load. Must be measured with 10G meter such as Agilent 34410A,
normal 10M DVM will read erroneously.
[1] For doubler mode of operation, pin 28 (RF_N) and pin 29 (RF_P) outputs must be shorted together.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 8
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
Outline Drawing
Part Number Package Body Material Lead Finish MSL Rating Package Marking [1]
HMC839LP6CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 H839
XXXX
[1] 4-Digit lot number XXXX
Package Information
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR
SUGGESTED PCB LAND PATTERN.
Absolute Maximum Ratings
AVDD, RVDD, DVDD3V, VCCPD,
VCCHF, VCCPS -0.3V to +3.6V
VPP CP, V D D CP, VC C1 -0.3V to +5.8V
VCC2 -0.3V to +5.5V
Operating Temperature -40°C to +85°C
Storage Temperature -65°C to 125°C
Maximum Junction Temperature 125 °C
Thermal Resistance (RTH)
(junction to ground paddle) 20 °C/W
Reow Soldering
Peak Temperature 260°C
Time at Peak Temperature 40 sec
ESD Sensitivity (HBM) Class 1B
Stresses above those listed under Absolute Maximum
Ratings may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device at these or any other conditions above those
indicated in the operational section of this specication
is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 9
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
Evaluation PCB, fo & fo/2 Modes
The circuit board used in the application should use RF circuit design techniques. Signal lines should have
50 Ohm impedance while the package ground leads and exposed paddle should be connected directly
to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the
top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
Evaluation PCB Schematic
To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC839LP6CE from the
“Search by Part Number” pull down menu to view the product splash page.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 10
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
Item Description
J1, J2 PCB Mount SMA RF Connector
J3 Dual Row Terminal Strip
J4 - J6 Connector Header
C1, C15 - C17, C25 10 µF Capacitor, 0805 Pkg.
C2, C3, C6, C7, C11, C12,
C14, C18, C27, C43, C45 0.47 µF Capacitor, 0402 Pkg.
C4, C13 22 pF Capacitor, 0402 Pkg.
C5, C33 1000 pF Capacitor, 0402 Pkg.
C8 3.9 pF Capacitor, 0402 Pkg.
C19 - C24, C28, C30, C32, C34 0.1 µF Capacitor, 0402 Pkg.
C26 1 µF Capacitor, 0603 Pkg.
C29 47 pF Capacitor, 0402 Pkg.
C35 3300 pF Capacitor, 0402 Pkg.
C36 270 pF Capacitor, 0402 Pkg.
C37, C38 68 pF Capacitor, 0402 Pkg.
C39 - C42, C44 4.7 µF Tantalum Capacitor, 0805 Pkg
R1, R2, R5, R8, R11, R15,
R18, R19, R21, R24 0 Ohm Resistor, 0402 Pkg.
R3, R4 1 Ohm Resistor, 0402 Pkg.
R6, R7 0 Ohm Resistor, 0805 Pkg.
R12, R20, R29 51 Ohm Resistor, 0402 Pkg.
R22, R25 20 kOhm Resistor, 0402 Pkg.
R26 - R28 1k Ohm Resistor, 0402 Pkg.
L1 3.9 nH Inductor, 0402 Pkg.
TP3, TP4 Test Point PC Compact SMT
U1 HMC839LP6CE PLL with Integrated VCO
U2 HMC860LP3E
Low Noise Quad Linear Regulator
Y1 3.3V, 50 MHz VCXO Crystal Oscillator
PCB [2] 125998 Evaluation Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4
List of Materials for
Evaluation PCB 129513, fo & fo/2 Modes [1]
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 11
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
Evaluation PCB, 2xfo Mode
The circuit board used in the application should use RF circuit design techniques. Signal lines should have
50 Ohm impedance while the package ground leads and exposed paddle should be connected directly
to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the
top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
Evaluation PCB Schematic
To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC839LP6CE from the
“Search by Part Number” pull down menu to view the product splash page.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
PLLS W/ INTEGRATED VCO - SMT
0 - 12
HMC839LP6CE
v0 3.1211
FRACTIONAL-N PLL WITH INTEGRATED VCO
1050 -1205, 2100 - 2410, 4200 - 4820 MHz
List of Materials for
Evaluation PCB 129514, 2xfo Mode [1]
Item Description
J1, J2 PCB Mount SMA RF Connector
J3 Dual Row Terminal Strip
J4 - J6 Connector Header
C1, C15 - C17, C25 10 µF Capacitor, 0805 Pkg.
C2, C3, C6, C7, C11, C12,
C14, C18, C27, C43, C45 0.47 µF Capacitor, 0402 Pkg.
C4, C13 22 pF Capacitor, 0402 Pkg.
C5, C33 1000 pF Capacitor, 0402 Pkg.
C8 8.2 pF Capacitor, 0402 Pkg.
C19 - C24, C28, C30, C32, C34 0.1 µF Capacitor, 0402 Pkg.
C26 1 µF Capacitor, 0603 Pkg.
C29 1 pF Capacitor, 0402 Pkg.
C31 0.7 pF Capacitor, 0402 Pkg.
C35 3300 pF Capacitor, 0402 Pkg.
C36 270 pF Capacitor, 0402 Pkg.
C37, C38 68 pF Capacitor, 0402 Pkg.
C39 - C42, C44 4.7 µF Tantalum Capacitor, 0805 Pkg
C46 27 pF Capacitor, 0402 Pkg.
C47 47 pF Capacitor, 0402 Pkg.
R1, R2, R8, R11, R15, R18, R19, R21, R24 0 Ohm Resistor, 0402 Pkg.
R3, R4 1 Ohm Resistor, 0402 Pkg.
R12, R20, R29 51 Ohm Resistor, 0402 Pkg.
R13, R14, R30 220 kOhm Resistor, 0402 Pkg.
R22, R25 20 kOhm Resistor, 0402 Pkg.
R26 - R28 1 kOhm Resistor, 0402 Pkg.
R31 0 Ohm Resistor, 0201 Pkg.
R32, R33 0 Ohm Resistor, 0805 Pkg.
L1 15 nH Inductor, 0402 Pkg.
L2, L3 47 nH Inductor, 0402 Pkg.
L4 0 Ohm Resistor, 0402 Pkg.
TP3, TP4 Test Point PC Compact SMT
U1 HMC839LP6CE PLL with Integrated VCO
U2 HMC860LP3E
Low Noise Quad Linear Regulator
Y1 3.3V, 50 MHz VCXO Crystal Oscillator
PCB [2] 127729 Evaluation Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4
