GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Features RoHS Compliant EZ-SEQUENCE TM Compliant to RoHS EU Directive 2011/65/EU (-Z versions) Compliant to RoHS EU Directive 2011/65/EU under exemption 7b (Lead solder exemption). Exemption 7b will expire after June 1, 2016 at which time this product will no longer be RoHS compliant (non-Z versions) Flexible output voltage sequencing EZ-SEQUENCETM Delivers up to 16A output current High efficiency - 92% at 3.3V full load (VIN = 12.0V) Small size and low profile: 50.8 mm x 12.7 mm x 8.1 mm Applications (2.00 in x 0.5 in x 0.32 in) Distributed power architectures Low output ripple and noise Intermediate bus voltage applications Constant switching frequency (300KHz) Telecommunications equipment High Reliability: Servers and storage applications Networking equipment Programmable Output voltage Enterprise Networks Line Regulation: 0.3% (typical) Latest generation IC's (DSP, FPGA, ASIC) and Microprocessor powered applications Load Regulation: 0.4% (typical) Temperature Regulation: 0.4 % (typical) Remote On/Off Remote Sense Output overcurrent protection (non-latching) Wide operating temperature range (-40C to 85C) UL* 60950-1Recognized, CSA C22.2 No. 60950-1-03 Certified, and VDE 0805:2001-12 (EN60950-1) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Calculated MTBF = 9.2M hours at 25oC Full-load Description Austin SuperLynxTM II 12V SIP (single in-line package) power modules are non-isolated dc-dc converters that can deliver up to 16A of output current with full load efficiency of 92% at 3.3V output. These modules provide a precisely regulated output voltage programmable via an external resistor from 0.75Vdc to 5.0Vdc over a wide range of input voltage (VIN = 8.3 - 14Vdc). Austin SuperLynxTM II has a sequencing feature, EZ-SEQUENCETM that enable designers to implement various types of output voltage sequencing when powering multiple modules on board. Their open-frame construction and small footprint enable designers to develop cost- and space-efficient solutions. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards August 19, 2016 (c)2016 General Electric Company. All rights reserved. GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit All VIN -0.3 15 Vdc Sequencing voltage All Vseq -0.3 VIN,max Vdc Operating Ambient Temperature All TA -40 85 C All Tstg -55 125 C Input Voltage Continuous (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Vo,set 3.63 VIN 8.3 12.0 14.0 Vdc Vo,set > 3.63 VIN 8.3 12.0 13.2 Vdc All IIN,max 10 Adc Input No Load Current Vo = 0.75Vdc IIN,No load 40 mA (VIN = VIN, nom, Io = 0, module enabled) Vo = 5.0Vdc IIN,No load 100 mA All IIN,stand-by 2 mA Inrush Transient All I2t Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1H source impedance; VIN=10V to 14V, IO= IOmax ; See Test configuration section) All 30 mAp-p Input Ripple Rejection (120Hz) All 30 dB Operating Input Voltage Maximum Input Current (VIN= VIN, min to VIN, max, IO=IO, max ) Input Stand-by Current (VIN = VIN, nom, module disabled) 0.4 A2s CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 15 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer's data sheet for further information. August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 2 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Electrical Specifications (continued) Parameter Output Voltage Set-point Device Symbol Min Typ Max Unit All VO, set -2.0 VO, set +2.0 % VO, set All VO, set -2.5% +3.5% % VO, set All VO 0.7525 5.5 Vdc (VIN=IN, min, IO=IO, max, TA=25C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All 0.3 % VO, set Load (IO=IO, min to IO, max) All 0.4 % VO, set Temperature (Tref=TA, min to TA, max) All 0.4 % VO, set 12 30 mVrms 75 mVpk-pk Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Cout = 1F ceramic//10Ftantalum capacitors) Vo 3.63 RMS (5Hz to 20MHz bandwidth) Peak-to-Peak (5Hz to 20MHz bandwidth) Vo 3.63 30 RMS (5Hz to 20MHz bandwidth) Vo = 5.0V 25 40 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) Vo = 5.0V 70 100 mVpk-pk F External Capacitance ESR 1 m All CO, max 1000 5000 F 16 Adc ESR 10 m All CO, max Output Current All Io 0 Output Current Limit Inception (Hiccup Mode ) All IO, lim 180 % Io All IO, s/c 3 Adc 79.0 % VIN= VIN, nom, TA=25C VO, set = 0.75Vdc VO, set = 1.2Vdc 85.0 % IO=IO, max , VO= VO,set VO,set = 1.5Vdc 87.0 % VO,set = 1.8Vdc 88.0 % VO,set = 2.5Vdc 90.5 % VO,set = 3.3Vdc 92.0 % VO,set = 5.0Vdc 94.0 % All fsw 300 kHz All Vpk 200 mV (VO= 90% of VO, set) Output Short-Circuit Current (VO250mV) ( Hiccup Mode ) Efficiency Switching Frequency Dynamic Load Response (dIo/dt=2.5A/s; VIN = VIN, nom; TA=25C) Load Change from Io= 50% to 100% of Io,max; 1F ceramic// 10 F tantalum Peak Deviation Settling Time (Vo<10% peak deviation) All ts 25 s (dIo/dt=2.5A/s; VIN = VIN, nom; TA=25C) Load Change from Io= 100% to 50%of Io,max: 1F ceramic// 10 F tantalum All Vpk 200 mV All ts 25 s Peak Deviation Settling Time (Vo<10% peak deviation) August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 3 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit (dIo/dt=2.5A/s; V VIN = VIN, nom; TA=25C) Load Change from Io= 50% to 100% of Io,max; Co = 2x150 F polymer capacitors Peak Deviation All Vpk 100 mV Settling Time (Vo<10% peak deviation) All ts 50 s (dIo/dt=2.5A/s; VIN = VIN, nom; TA=25C) Load Change from Io= 100% to 50%of Io,max: Co = 2x150 F polymer capacitors Peak Deviation All Vpk 100 mV Settling Time (Vo<10% peak deviation) All ts 50 s Dynamic Load Response General Specifications Parameter Min Calculated MTBF (IO=IO, max, TA=25C) Typ Max 9,230,550 Unit Hours Telecordia SR-332 Issue 1: Method 1 Case 3 Weight August 19, 2016 5.6 (0.2) (c)2012 General Electric Company. All rights reserved. g (oz.) Page 4 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit Input High Voltage (Module ON) All VIH VIN, max V Input High Current All IIH 10 A Input Low Voltage (Module OFF) All VIL -0.2 0.3 V Input Low Current All IIL 0.2 1 mA Input High Voltage (Module OFF) All VIH 2.5 Input High Current All IIH Input Low Voltage (Module ON) All VIL Input low Current All IIL Case 1: On/Off input is set to Logic Low (Module ON) and then input power is applied (delay from instant at which VIN =VIN, min until Vo=10% of Vo,set) Case 2: Input power is applied for at least one second and then the On/Off input is set to logic Low (delay from instant at which Von/Off=0.3V until Vo=10% of Vo, set) All Tdelay All Output voltage Rise time (time for Vo to rise from 10% of Vo,set to 90% of Vo, set) All On/Off Signal interface Device code with Suffix "4" - Positive logic (On/Off is open collector/drain logic input; Signal referenced to GND - See feature description section) Device Code with no suffix - Negative Logic (On/OFF pin is open collector/drain logic input with external pull-up resistor; signal referenced to GND) VIN,max Vdc 0.2 1 mA 0.3 Vdc 10 A 3 msec Tdelay 3 msec Trise 4 6 msec 1 % VO, set -0.2 Turn-On Delay and Rise Times (IO=IO, max , VIN = VIN, nom, TA = 25 oC, ) Output voltage overshoot - Startup IO= IO, max; VIN = 8.3 to 14Vdc, TA = 25 oC Sequencing Delay time Delay from VIN, min to application of voltage on SEQ pin Tracking Accuracy (Power-Up: 2V/ms) (Power-Down: 1V/ms) All All All TsEQdelay 10 |VSEQ -Vo | |VSEQ -Vo | msec 100 200 mV 300 500 mV 125 C (VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo) Overtemperature Protection All Tref (See Thermal Consideration section) Input Undervoltage Lockout Turn-on Threshold All 7.9 V Turn-off Threshold All 7.8 V August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 5 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Characteristic Curves 90 94 88 92 86 90 84 88 82 86 EFFICIENCY, () EFFICIENCY, () The following figures provide typical characteristics for the Austin SuperLynxTM II 12V SIP modules at 25C. 80 78 76 Vin=14V 74 84 82 80 Vin=14V 78 Vin=12V 76 Vin=10V 74 Vin=12V 72 70 Vin=10V 0 0 4 8 12 4 OUTPUT CURRENT, IO (A) 92 86 90 84 88 82 86 EFFICIENCY, () EFFICIENCY, () 94 88 80 78 76 Vin=14V 74 70 84 82 80 Vin=14V 78 Vin=12V 76 Vin=10V 74 72 Vin=12V Vin=10V 0 8 16 Figure 4. Converter Efficiency versus Output Current (Vout = 2.5Vdc). 90 4 12 OUTPUT CURRENT, IO (A) Figure 1. Converter Efficiency versus Output Current (Vout = 1.2Vdc). 0 8 16 12 4 8 12 16 16 OUTPUT CURRENT, IO (A) Figure 2. Converter Efficiency versus Output Current (Vout = 1.5Vdc). OUTPUT CURRENT, IO (A) Figure 5. Converter Efficiency versus Output Current (Vout = 3.3Vdc). 92 96 90 94 92 88 90 86 EFFICIENCY, () EFFICIENCY, () 88 84 82 80 78 Vin=14V 76 74 72 86 84 82 80 Vin=14V 78 Vin=12V 76 Vin=10V 74 Vin=12V Vin=10V 0 0 4 8 12 8 12 16 16 OUTPUT CURRENT, IO (A) Figure 3. Converter Efficiency versus Output Current (Vout = 1.8Vdc). August 19, 2016 4 OUTPUT CURRENT, IO (A) Figure 6. Converter Efficiency versus Output Current (Vout =5.0Vdc). (c)2012 General Electric Company. All rights reserved. Page 6 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Characteristic Curves (continued) The following figures provide typical characteristics for the SuperLynxTM II 12V SIP modules at 25C. 9 Io = 16A 8 2 1 0 8 9 10 11 12 INPUT VOLTAGE, VIN (V) Figure 7. Input Voltage vs. Input Current 14 TIME, t (5s/div) Figure 10. Transient Response to Dynamic Load Change from 50% to 100% of full load (Vo = 3.3Vdc). VO (V) (20mV/div) OUTPUT CURRENT, OUTPUT VOLTAGE (Vo = 3.3 Vdc). OUTPUT VOLTAGE 13 Figure 9. Typical Output Ripple and Noise (Vin = 12V dc, Vo = 3.3Vdc, Io=16A). August 19, 2016 IO (A) (2A/div) TIME, t (2s/div) VO (V) (200mV/div) Figure 11. Transient Response to Dynamic Load Change from 100% to 50% of full load (Vo = 3.3Vdc). VO (V) (20mV/div) Figure 8. Typical Output Ripple and Noise (Vin = 12V dc, Vo = 2.5 Vdc, Io=16A). OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (5s/div) OUTPUT VOLTAGE TIME, t (2s/div) VO (V) (200mV/div) 7 IO (A) (2A/div) 3 OUTPUT CURRENT, OUTPUT VOLTAGE 5 4 IO (A) (2A/div) INPUT CURRENT, IIN (A) Io=0A 6 VO (V) (200mV/div) Io=8A 7 TIME, t (10s/div) Figure 12. Transient Response to Dynamic Load Change from 50% to 100% of full load (Vo =3.3Vdc, Cext = 2x150 F Polymer Capacitors). (c)2012 General Electric Company. All rights reserved. Page 7 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Characteristic Curves (continued) V o (V) OUTPUT VOLTAGE, INPUT VOLTAGE VIN (V) (5V/div) (2V/div) VO (V) (200mV/div) TIME, t (10s/div) TIME, t 2ms/div) TIME, t (2ms/div) VOV) (2V/div) OUTPUT CURRENT, VOn/off (V) (5V/div) (Vin = 12Vdc, Vo = 5.0Vdc, Io =16A). Figure 17. Typical Start-Up with Prebias (Vin = 12Vdc, Vo = 2.5Vdc, Io = 1A, Vbias =1.2 Vdc). IO (A) (10A/div) Figure 14. Typical Start-Up Using Remote On/Off OUTPUT VOLTAGE On/Off VOLTAGE TIME, t (2 ms/div) Figure 16. Typical Start-Up with application of Vin with low-ESR polymer capacitors at the output (7x150 F) (Vin = 12Vdc, Vo = 5.0Vdc, Io = 16A, Co = 1050 F). OUTPUT VOLTAGE VOn/off (V) (5V/div) VOV) (2V/div) OUTPUT VOLTAGE On/Off VOLTAGE Figure 13. Transient Response to Dynamic Load Change from 100% of 50% full load (Vo = 3.3Vdc, Cext = 2x150 F Polymer Capacitors) VOV) (1V/div) IO (A) (2A/div) OUTPUT CURRENT, OUTPUT VOLTAGE The following figures provide typical characteristics for the Austin SuperLynxTM II 12V SIP modules at 25C. TIME, t (2ms/div) TIME, t (10ms/div) Figure 15. Typical Start-Up Using Remote On/Off with Low- Figure 18. Output short circuit Current ESR external capacitors (7x150uF Polymer) (Vin = 12Vdc, Vo = 0.75Vdc). (Vin = 12Vdc, Vo = 5.0Vdc, Io = 16A, Co = 1050F). August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 8 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Characteristic Curves (continued) 18 18 16 16 14 14 OUTPUT CURRENT, Io (A) OUTPUT CURRENT, Io (A) The following figures provide thermal derating curves for the Austin SuperLynx TM II 12V SIP modules. 12 10 NC 8 100 LFM 6 200 LFM 4 300 LFM 2 400 LFM 0 20 30 12 10 NC 8 6 4 2 0 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA OC Figure 19. Derating Output Current versus Local Ambient Temperature and Airflow (Vin = 12Vdc, Vo=0.75Vdc). 100 LFM 200 LFM 300 LFM 400 LFM 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA OC Figure 22. Derating Output Current versus Local Ambient Temperature and Airflow (Vin = 12dc, Vo=5.0 Vdc). 18 OUTPUT CURRENT, Io (A) 16 14 12 10 NC 8 6 4 2 0 100 LFM 200 LFM 300 LFM 400 LFM 20 30 40 50 60 70 AMBIENT TEMPERATURE, 80 90 T A OC Figure 20. Derating Output Current versus Local Ambient Temperature and Airflow (Vin = 12Vdc, Vo=1.8 Vdc). 18 OUTPUT CURRENT, Io (A) 16 14 12 10 NC 8 6 4 2 0 100 LFM 200 LFM 300 LFM 400 LFM 20 30 40 50 60 70 AMBIENT TEMPERATURE, 80 90 T A OC Figure 21. Derating Output Current versus Local Ambient Temperature and Airflow (Vin = 12Vdc, Vo=3.3 Vdc). August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 9 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Test Configurations Design Considerations Input Filtering CURRENT PROBE TO OSCILLOSCOPE The Austin SuperLynxTM II 12V SIP module should be connected to a low-impedance source. A highly inductive source can affect the stability of the module. An input capacitance must be placed directly adjacent to the input pin of the module, to minimize input ripple voltage and ensure module stability. LTEST VIN(+) BATTERY 1H CIN CS 1000F Electrolytic 2x100F Tantalum E.S.R.<0.1 @ 20C 100kHz COM NOTE: Measure input reflected ripple current with a simulated source inductance (LTEST) of 1H. Capacitor CS offsets possible battery impedance. Measure current as shown above. Figure 23. Input Reflected Ripple Current Test Setup. COPPER STRIP VO (+) RESISTIVE LOAD 1uF . 10uF In a typical application, 6x47 F low-ESR tantalum capacitors (AVX part #: TPSE476M025R0100, 47F 25V 100 m ESR tantalum capacitor) will be sufficient to provide adequate ripple voltage at the input of the module. To further minimize ripple voltage at the input, very low ESR ceramic capacitors are recommended at the input of the module. Figure 26 shows input ripple voltage (mVpp) for various outputs with 6x47 F tantalum capacitors and with 6x22 F ceramic capacitor (TDK part #: C4532X5R1C226M) at full load. SCOPE 350 GROUND PLANE NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 24. Output Ripple and Noise Test Setup. Rdistribution Rcontact Rcontact VIN(+) Rdistribution VO Input Ripple Voltage (mVp-p) COM 300 250 200 150 100 Tantalum 50 Ceramic 0 0 Rdistribution RLOAD VO VIN Rcontact Rcontact COM Rdistribution COM 1 2 3 4 5 Output Voltage (Vdc) Figure 26. Input ripple voltage for various output with 6x47 F tantalum capacitors and with 6x22 F ceramic capacitors at the input (full load). NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 25. Output Voltage and Efficiency Test Setup. VO. IO Efficiency August 19, 2016 = VIN. IIN x 100 % (c)2012 General Electric Company. All rights reserved. Page 10 6 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Design Considerations (continued) Output Filtering The Austin SuperLynxTM II 12V SIPmodule is designed for low output ripple voltage and will meet the maximum output ripple specification with 1 F ceramic and 10 F tantalum capacitors at the output of the module. However, additional output filtering may be required by the system designer for a number of reasons. First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. To reduce the output ripple and improve the dynamic response to a step load change, additional capacitance at the output can be used. Low ESR polymer and ceramic capacitors are recommended to improve the dynamic response of the module. For stable operation of the module, limit the capacitance to less than the maximum output capacitance as specified in the electrical specification table. August 19, 2016 Safety Considerations For safety agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., UL 60950-1, CSA C22.2 No. 60950-1-03, and VDE 0850:2001-12 (EN60950-1) Licensed. For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. The input to these units is to be provided with a fastacting fuse with a maximum rating of 6A in the positive input lead. (c)2012 General Electric Company. All rights reserved. Page 11 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Feature Descriptions VIN+ Remote On/Off Austin SuperLynxTM II 12V SIP power modules feature an On/Off pin for remote On/Off operation. Two On/Off logic options are available in the Austin SuperLynxTM II series modules. Positive Logic On/Off signal, device code suffix "4", turns the module ON during a logic High on the On/Off pin and turns the module OFF during a logic Low. Negative logic On/Off signal, no device code suffix, turns the module OFF during logic High and turns the module ON during logic Low. For positive logic modules, the circuit configuration for using the On/Off pin is shown in Figure 27. The On/Off pin is an open collector/drain logic input signal (Von/Off) that is referenced to ground. During a logic-high (On/Off pin is pulled high internal to the module) when the transistor Q1 is in the Off state, the power module is ON. Maximum allowable leakage current of the transistor when Von/off = VIN,max is 10A. Applying a logic-low when the transistor Q1 is turned-On, the power module is OFF. During this state VOn/Off must be less than 0.3V. When not using positive logic On/off pin, leave the pin unconnected or tie to VIN. VIN+ MODULE R2 ON/OFF + I ON/OFF I ON/OFF ON/OFF + VON/OFF PWM Enable R1 Q2 CSS Q1 R2 GND _ Figure 28. Circuit configuration for using negative logic On/OFF. Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. The typical average output current during hiccup is 3A. Input Undervoltage Lockout Q2 R1 VON/OFF PWM Enable R3 Q1 Q3 CSS R4 GND MODULE Rpull-up _ Figure 27. Circuit configuration for using positive logic On/OFF. At input voltages below the input undervoltage lockout limit, module operation is disabled. The module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. Overtemperature Protection To provide protection in a fault condition, the unit is equipped with a thermal shutdown circuit. The unit will shutdown if the thermal reference point Tref, exceeds 125oC (typical), but the thermal shutdown is not intended as a guarantee that the unit will survive temperatures beyond its rating. The module will automatically restarts after it cools down. For negative logic On/Off devices, the circuit configuration is shown is Figure 28. The On/Off pin is pulled high with an external pull-up resistor (typical Rpull-up = 68k, +/- 5%). When transistor Q1 is in the Off state, logic High is applied to the On/Off pin and the power module is Off. The minimum On/off voltage for logic High on the On/Off pin is 2.5 Vdc. To turn the module ON, logic Low is applied to the On/Off pin by turning ON Q1. When not using the negative logic On/Off, leave the pin unconnected or tie to GND. August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 12 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Feature Descriptions (continued) Output Voltage Programming The output voltage of the Austin SuperLynxTM II 12V can be programmed to any voltage from 0.75Vdc to 5.5Vdc by connecting a resistor (shown as Rtrim in Figure 29) between the Trim and GND pins of the module. Without an external resistor between the Trim and GND pins, the output of the module will be 0.7525Vdc. To calculate the value of the trim resistor, Rtrim for a desired output voltage, use the following equation: 10500 Rtrim 1000 Vo 0 . 7525 Rtrim is the external resistor in Vo is the desired output voltage For example, to program the output voltage of the Austin SuperLynxTM II module to 1.8V, Rtrim is calculated as follows: 10500 1000 1 . 8 0 . 75 Rtrim Rtrim 9.024k The amount of power delivered by the module is defined as the voltage at the output terminals multiplied by the output current. When using the trim feature, the output voltage of the module can be increased, which at the same output current would increase the power output of the module. Care should be taken to ensure that the maximum output power of the module remains at or below the maximum rated power (Pmax = Vo,set x Io,max). Voltage Margining Output voltage margining can be implemented in the Austin SuperLynxTM II modules by connecting a resistor, Rmargin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to the Output pin for margining-down. Figure 30 shows the circuit configuration for output voltage margining. The POL Programming Tool, available at www.gecriticalpower.com under the Design Tools section, also calculates the values of Rmargin-up and Rmargin-down for a specific output voltage and % margin. Please consult your local GE technical representative for additional details. Vo V IN(+) V O(+) Rmarg in-down Austin Lynx or Lynx II Series ON/OFF LOAD TRIM Q2 R trim Trim GND Rmarg in-up Rtri m Figure 29. Circuit configuration to program output voltage using an external resistor Q1 Table 1 provides Rtrim values for most common output voltages. Table 1 VO, set (V) Rtrim (K) 0.7525 Open 1.2 22.46 1.5 13.05 1.8 9.024 2.5 5.009 3.3 3.122 5.0 1.472 GND Figure 30. Circuit Configuration for margining Output voltage. By using 1% tolerance trim resistor, set point tolerance of 2% is achieved as specified in the electrical specification. The POL Programming Tool, available at www.gecriticalpower.com under the Design Tools section, helps determine the required external trim resistor needed for a specific output voltage. August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 13 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Feature Descriptions (continued) Voltage Sequencing Austin SuperLynxTM II 12V series of modules include a sequencing feature, EZ-SEQUENCETM that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When not using the sequencing feature, either tie the SEQ pin to VIN or leave it unconnected. SEQ pin not provided in -73Z codes. When an analog voltage is applied to the SEQ pin, the output voltage tracks this voltage until the output reaches the set-point voltage. The SEQ voltage must be set higher than the set-point voltage of the module. The output voltage follows the voltage on the SEQ pin on a one-to-one volt basis. By connecting multiple modules together, customers can get multiple modules to track their output voltages to the voltage applied on the SEQ pin. For proper voltage sequencing, first, input voltage is applied to the module. The On/Off pin of the module is left unconnected (or tied to GND for negative logic modules or tied to VIN for positive logic modules) so that the module is ON by default. After applying input voltage to the module, a minimum of 10msec delay is required before applying voltage on the SEQ pin. During this time, potential of 50mV ( 10 mV) is maintained on the SEQ pin. After 10msec delay, an analog voltage is applied to the SEQ pin and the output voltage of the module will track this voltage on a one-to-one volt bases until output reaches the setpoint voltage. To initiate simultaneous shutdown of the modules, the SEQ pin voltage is lowered in a controlled manner. Output voltage of the modules tracks the voltages below their set-point voltages on a one-to-one basis. A valid input voltage must be maintained until the tracking and output voltages reach ground potential to ensure a controlled shutdown of the modules. The amount of power delivered by the module is defined as the output voltage multiplied by the output current (Vo x Io). When using Remote Sense, the output voltage of the module can increase, which if the same output is maintained, increases the power output by the module. Make sure that the maximum output power of the module remains at or below the maximum rated power. When the Remote Sense feature is not being used, connect the Remote Sense pin to output pin of the module. Rdistribution Rcontact Rcontact Rdistribution VIN(+) VO Sense RLOAD Rdistribution Rcontact Rcontact Rdistribution COM COM Figure 31. Remote sense circuit configuration. When using the EZ-SEQUENCETM feature to control start-up of the module, pre-bias immunity feature during start-up is disabled. The pre-bias immunity feature of the module relies on the module being in the diode-mode during start-up. When using the EZ-SEQUENCETM feature, modules goes through an internal set-up time of 10msec, and will be in synchronous rectification mode when voltage at the SEQ pin is applied. This will result in sinking current in the module if pre-bias voltage is present at the output of the module. When pre-bias immunity during start-up is required, the EZ-SEQUENCETM feature must be disabled. For additional guidelines on using EZ-SEQUENCETM feature of Austin SuperLynxTM II 12V, contact GE technical representative for preliminary application note on output voltage sequencing using Austin Lynx II series. Remote Sense The Austin SuperLynxTM II 12V SIP power modules have a Remote Sense feature to minimize the effects of distribution losses by regulating the voltage at the Remote Sense pin (See Figure 31). The voltage between the Sense pin and Vo pin must not exceed 0.5V. August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 14 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 33. Note that the airflow is parallel to the long axis of the module as shown in figure 32. The derating data applies to airflow in either direction of the module's long axis. 25.4_ (1.0) Wind Tunnel PWBs Power Module 76.2_ (3.0) x Tref Air Flow 7.24_ (0.285) Probe Location for measuring airflow and ambient temperature Air flow Figure 33. Thermal Test Set-up. Heat Transfer via Convection Top View Figure 32. Tref Temperature measurement location. The thermal reference point, Tref 1 used in the specifications of thermal derating curves is shown in Figure 32. For reliable operation this temperature should not exceed 125oC. The output power of the module should not exceed the rated power of the module (Vo,set x Io,max). Increased airflow over the module enhances the heat transfer via convection. Thermal derating curves showing the maximum output current that can be delivered by various module versus local ambient temperature (TA) for natural convection and up to 1m/s (200 ft./min) are shown in the Characteristics Curves section. Please refer to the Application Note "Thermal Characterization Process For Open-Frame Board-Mounted Power Modules" for a detailed discussion of thermal aspects including maximum device temperatures. August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 15 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Post solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Board Mounted Power Modules: Soldering and Cleaning Application Note. Through-Hole Lead-Free Soldering Information The RoHS-compliant through-hole products use the SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant components. They are designed to be processed through single or dual wave soldering machines. The pins have an RoHS-compliant finish that is compatible with both Pb and Pb-free wave soldering processes. A maximum preheat rate of 3C/s is suggested. The wave preheat process should be such that the temperature of the power module board is kept below 210C. For Pb solder, the recommended pot temperature is 260C, while the Pb-free solder pot is 270C max. Not all RoHS-compliant through-hole products can be processed with paste-through-hole Pb or Pbfree reflow process. If additional information is needed, please consult with your GE technical representative for more details. August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 16 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Mechanical Outline Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) Top View Side View Bottom View PIN FUNCTION 1 Vo 2 Vo 3 Sense+ 4 Vo 5 GND 6 GND 7 VIN 8 VIN B SEQ** 9 Trim 10 On/Off ** SEQ removed for -73Z codes August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 17 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) PIN FUNCTION 1 Vo 2 Vo 3 Sense+ 4 Vo 5 GND 6 GND 7 VIN 8 VIN B SEQ** 9 Trim 10 On/Off ** SEQ removed for -73Z codes Through- Hole Pad Layout - Back view August 19, 2016 (c)2012 General Electric Company. All rights reserved. Page 18 GE Data Sheet 12V Austin SuperLynxTMII: SIP Non-Isolated DC-DC Power Modules 8.3Vdc -14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current Ordering Information Please contact your GE Sales Representative for pricing, availability and optional features. Table 2. Device Codes Device Code Input Voltage Output Voltage Output Current Efficiency 3.3V@ 16A Connector Type ATA016A0X3 8.3 - 14Vdc 0.75 - 5.5Vdc 16 A 92.0% SIP 108989091 CC109104691 Comcodes ATA016A0X3Z 8.3 - 14Vdc 0.75 - 5.5Vdc 16 A 92.0% SIP ATA016A0X43 8.3 - 14Vdc 0.75 - 5.5Vdc 16 A 92.0% SIP 108989100 ATA016A0X43Z 8.3 - 14Vdc 0.75 - 5.5Vdc 16 A 92.0% SIP CC109104700 ATA016A0X3-73Z* 8.3 - 14Vdc 0.75 - 5.5Vdc 16 A 92.0% SIP 150052629 -Z refers to RoHS-compliant versions. *Special Codes, consult factory before ordering Table 3. Device Option Option* Long Pins 5.08 mm 0.25mm (0.200 in. 0.010 in.) Suffix** 5 * Contact GE Sales Representative for availability of these options, samples, minimum order quantity and lead times ** When adding multiple options to the product code, add suffix numbers in the descending order Contact Us For more information, call us at USA/Canada: +1 877 546 3243, or +1 972 244 9288 Asia-Pacific: +86.021.54279977*808 Europe, Middle-East and Africa: +49.89.878067-280 www.gecriticalpower.com GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. August 19, 2016 (c)2016 General Electric Company. All International rights reserved. Version 1.26