DATA SHEET GaAs INTEGRATED CIRCUIT PG2009TB L-BAND HIGH POWER SPDT SWITCH DESCRIPTION The PG2009TB is an L-band SPDT (Single Pole Double Throw) GaAs FET switch which was developed for digital cellular or cordless telephone application. The device can operate from 500 MHz to 2.5 GHz, having the low insertion loss and high isolation by 2.8 V control voltage. FEATURES * Low insertion loss * High isolation * High power : LINS = 0.25 dB TYP. @ Vcont1/2 = 2.8 V/0 V, f = 1.0 GHz LINS = 0.30 dB TYP. @ Vcont1/2 = 2.8 V/0 V, f = 2.0 GHz : ISL = 28 dB TYP. @ Vcont1/2 = 2.8 V/0 V, f = 2.0 GHz : Pin (0.1dB) = 34 dBm TYP. @ Vcont1/2 = 2.8 V/0 V, f = 1.0 GHz * 6-pin super minimold package (2.0 x 1.25 x 0.9 mm) APPLICATION * L-band digital cellular or cordless telephone * BuletoothTM, W-LAN and WLL applications ORDERING INFORMATION Part Number PG2009TB-E3 Package 6-pin super minimold Marking G2U Supplying Form * Embossed tape 8 mm wide * Pin 1, 2, 3 face the perforation side of the tape * Qty 3 kpcs/reel Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: PG2009TB-A Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Document No. PG10191EJ02V0DS (2nd edition) Date Published July 2004 CP(K) The mark shows major revised points. PG2009TB PIN CONNECTIONS 3 2 1 G2U (Top View) (Bottom View) 4 4 3 5 5 2 6 6 1 Pin No. Pin Name 1 OUT1 2 GND 3 OUT2 4 Vcont2 5 IN 6 Vcont1 ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified) Parameter Control Voltage 1, 2 Symbol Ratings Vcont1, 2 -6.0 to +6.0 Unit V Note Input Power Pin +36 dBm Total Power Dissipation Ptot 0.15 W Operating Ambient Temperature TA -45 to +85 C Storage Temperature Tstg -55 to +150 C Note Vcont1-Vcont2 6.0 V RECOMMENDED OPERATING RENGE (TA = +25C) Parameter Symbol MIN. TYP. MAX. Unit Control Voltage (High) Vcont(H) +2.7 +2.8 +3.0 V Control Voltage (Low) Vcont(L) -0.2 0 +0.2 V 2 Data Sheet PG10191EJ02V0DS PG2009TB ELECTRICAL CHARACTERISTICS (TA = +25C, Vcont1 = 2.8 V, Vcont2 = 0 V or Vcont1 = 0 V, Vcont2 = 2.8 V, ZO = 50 , Off chip DC blocking capacitors value; 56 pF, unless otherwise specified) Parameter Insertion Loss Symbol LINS Isolation ISL Test Conditions MIN. TYP. MAX. Unit f = 0.5 to 1.0 GHz - 0.25 0.45 dB f = 2.0 GHz - 0.30 0.50 dB f = 2.5 GHz - 0.40 - dB f = 0.5 to 2.0 GHz 24 28 - dB f = 2.5 GHz - 25 - dB Input Return Loss RLin f = 0.5 to 2.5 GHz 15 20 - dB Output Return Loss RLout f = 0.5 to 2.5 GHz 15 20 - dB 32.5 34 - dBm 65 75 - dBc 65 75 - dBc - 150 - ns - 1 50 A Input Power at 0.1 dB Compression Point Pin(0.1 dB) 2nd Harmonics f = 1.0 GHz, Vcont = 2.8 V/0 V Note 2f0 f = 1.0 GHz, Vcont = 2.8 V/0 V, Pin = 30.5 dBm 3rd Harmonics 3f0 f = 1.0 GHz, Vcont = 2.8 V/0 V, Pin = 30.5 dBm Switching Speed tSW Control Current Icont Vcont = 2.8 V/0 V, RF Non Note Pin(0.1 dB) are measured the input power level when the insertion loss increase more 0.1 than that of linear range. All other characteristics are measured in linear range. Caution When the PG2009TB is used it is necessary to use DC blocking capacitors for No.1 (OUT1), No.3 (OUT2) and No.5 (IN). The value of DC blocking capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with actual board of your system. The range of recommended DC blocking capacitor value is less than 100 pF. Data Sheet PG10191EJ02V0DS 3 PG2009TB EVALUATION CIRCUIT Vcont1 = 2.8 V, Vcont2 = 0 V or Vcont2 = 0 V, Vcont1 = 2.8 V, off chip DC blocking capacitors value C1 = 56 pF, C2 = 1 000 pF (Bypass), using the standard evaluation board. C2 5 IN C1 4 Vcont2 G2U 6 Vcont1 1 C1 OUT1 2 3 C1 C2 OUT2 EVALUATION BOARD Vcont1 6pin SMM SPDT SW OUT1 C2 C1 G2U IN C1 C1 C2 OUT2 Vcont2 TRUTH TABLE 4 Vcont1 Vcont2 IN-OUT1 IN-OUT2 Low High OFF ON High Low ON OFF Data Sheet PG10191EJ02V0DS PG2009TB TYPICAL CHARACTERISTICS (TA = +25C, Vcont1/2 = 2.8 V/0 V, Pin = 0 dBm, OUT2 side is 50 termination, unless otherwise specified) ISOLATION vs. FEQUENCY INPUT RETURN LOSS vs. FREQUENCY log MAG 10 dB/ REF 0 dB 0 1: -25.43 dB 1.0 GHz 2: -30.339 dB 1.5 GHz 3: -30.025 dB 2.0 GHz 4: -23.812 dB 2.5 GHz 5: -17.85 dB 3.0 GHz 1 -20 2 -40 START 0.500 000 000 GHz 3 CH1 S21 5 4 Isolation ISL (dB) Input Return Loss RLin (dB) CH1 S11 log MAG 0 -20 2 -40 START 0.500 000 000 GHz STOP 3.000 000 000 GHz -2.0 1 2 3 1: -0.620 dB 1.0 GHz 2: -0.744 dB 1.5 GHz 3: -0.881 dB 2.0 GHz 4: -1.057 dB 2.5 GHz 5: -1.302 dB 3.0 GHz 4 5 -4.0 5 STOP 3.000 000 000 GHz STOP 3.000 000 000 GHz log MAG 10 dB/ REF 0 dB 0 1: -25.992 dB 1.0 GHz 2: -31.882 dB 1.5 GHz 3: -32.46 dB 2.0 GHz 4: -25.087 dB 2.5 GHz 5: -18.145 dB 3.0 GHz 1 -20 2 -40 START 0.500 000 000 GHz 4 OUTPUT RETERN LOSS vs. FREQUENCY CH1 S22 Output Return Loss RLout (dB) Insertion Loss LINS (dB) 0 1 dB/ REF 0 dB 3 Frequency f (GHz) INSERTION LOSS vs. FREQUENCY log MAG 1: -28.787 dB 1.0 GHz 2: -28.871 dB 1.5 GHz 3: -27.75 dB 2.0 GHz 4: -24.902 dB 2.5 GHz 5: -21.582 dB 3.0 GHz 1 Frequency f (GHz) CH1 S21 10 dB/ REF 0 dB START 0.500 000 000 GHz Frequency f (GHz) 3 4 5 STOP 3.000 000 000 GHz Frequency f (GHz) Caution These characteristics values include the losses of the evaluation board. Remark The graphs indicate nominal characteristics. Data Sheet PG10191EJ02V0DS 5 PG2009TB TYPICAL CHARACTERISTICS (f = 2 GHz, OUT2 side is 50 termination, unless otherwise specified) 0 RELATION BETWEEN CONTROL VOLTAGE OF INSERSION LOSS Insersion Loss LINS (dB) 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Vcont = 2.4 V Vcont = 2.8 V Vcont = 3.2 V 0.9 25 26 27 28 29 30 31 32 33 34 35 36 37 0.8 Input Power Pin (dBm) Vcont = 2.4 V Vcont = 2.8 V Vcont = 3.2 V 2nd Harmonics 2f0 (dBc) 10 20 30 40 50 60 70 0 10 3rd Harmonics 3f0 (dBc) 0 RELATION BETWEEN CONTROL VOLTAGE OF 2nd HARMONICS 20 Vcont = 2.4 V Vcont = 2.8 V Vcont = 3.2 V 30 40 50 60 70 80 80 90 25 26 27 28 29 30 31 32 33 34 35 36 37 90 25 26 27 28 29 30 31 32 33 34 35 36 37 Input Power Pin (dBm) Input Power Pin (dBm) Remark The graphs indicate nominal characteristics. 6 RELATION BETWEEN CONTROL VOLTAGE OF 3rd HARMONICS Data Sheet PG10191EJ02V0DS PG2009TB PACKAGE DIMENSIONS 6-PIN SUPER MINIMOLD (UNIT: mm) 2.10.1 0.2+0.1 -0.05 0.65 0.65 1.3 Data Sheet PG10191EJ02V0DS 0.15+0.1 -0.05 0 to 0.1 0.7 0.1 MIN. 0.90.1 2.00.2 1.250.1 7 PG2009TB RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Preheating time at 120 to 180C : 12030 seconds Maximum chlorine content of rosin flux (% mass) : 3 times : 0.2%(Wt.) or below : 215C or below Preheating time at 120 to 150C : 30 to 60 seconds Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below Time at temperature of 200C or higher Peak temperature (molten solder temperature) IR260 : 60 seconds or less Peak temperature (package surface temperature) Maximum number of reflow processes Wave Soldering : 260C or below : 10 seconds or less Maximum number of reflow processes VPS Condition Symbol Time at peak temperature Time at temperature of 220C or higher For soldering : 25 to 40 seconds VP215 : 3 times : 260C or below Time at peak temperature : 10 seconds or less Maximum number of flow processes : 1 time Peak temperature (pin temperature) : 350C or below Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below WS260 Preheating temperature (package surface temperature) : 120C or below Maximum chlorine content of rosin flux (% mass) Partial Heating Soldering time (per side of device) : 0.2%(Wt.) or below : 3 seconds or less Caution Do not use different soldering methods together (except for partial heating). 8 Data Sheet PG10191EJ02V0DS HS350 PG2009TB SAFETY INFORMATION ON THIS PRODUCT Caution GaAs Products The product contains gallium arsenide, GaAs. GaAs vapor and powder are hazardous to human health if inhaled or ingested. * Do not destroy or burn the product. * Do not cut or cleave off any part of the product. * Do not crush or chemically dissolve the product. * Do not put the product in the mouth. Follow related laws and ordinances for disposal. The product should be excluded from general industrial waste or household garbage.